Text preview for : Bush_1433.pdf part of bush 1433 bush ctv1433
Back to : Bush_1433.pdf | Home
BUSH 1433
General Information Also Covers Bush 1434, 1435, 1473 T, 1474 T, 1435 GTV Alba CTV 3409, CTV 3459 Goodmans GTV 3409, GTV 3459 11 AK08 & 11AK20 Chassis Safety Notes
DO NOT CHANGE ANY MODULE UNLESS THE SET IS SWITCH OFF. The mains supply side of the switch mode power supply transformer is live. Use an isolating transformer. The receivers fulfill completely the sfety requirements. Safety precautions Servicing of this TV should only be carried out by a qualified person. · Components marked with the warning symbol on the circuit diagram are critical for safety and must only be replaced with an identical component. · Power resistor and fusable resistors must be mounted in an identical manner to the original component. · When servicing this TV, check that the EHT does not exceed 26 KV. TV set switched off: Make short-circuit between HV-CRT clip and CRT ground layer. Short 0808 (150µF) before changing IC801 or other components in primary side of SMPS. Measurements Voltage readings and oscilloscope traces are measured under following conditions. Antenna Signal 60 dBuV from colorbar generator. (100% white, 75% color saturation) Brightness, contrast, color set for a normal picture. Mains supply, 220V AC, 50 Hz. The adjustments should be carried out in the following order for convenience. SMPS SYSTEM VOLTAGE 1) Set the BCS (Brightness, Contrast, Saturation) and VOL (Volume) to minimum. 2) Check the voltage at the shorted pins of socket PL602 (TP1) 3) If necessary, adjust VR801 112 ± 0.5VDC (14" and 15 models) 4) Set the BCS and VOL to normal picture and sound VISION DEMODULATOR AND AFC 1) Set the pattern generator for 10mV, 38.9 MHz (B/G models) or 39.5 MHz (for I models) or 38.0 MHz (for 0/K models) RF output 2) Connect the RF output of the pattern generator to any one input of SAW filter and connect the other input of SAW filter to ground through 10 nF capacitor (No antenna input applied) 3) Check the voltage at the base of 0201 (TP2) 4) Adjust VL401 for 3.5 ± 0.1 Voc 2) PICTURE GEOMETRY AND FOCUS 1) Set the pattern generator for centre-cross, circle and cross-hatch composite pattern. 2) Adjust VR702 for vertical size, VR701 for vertical linearity, VR401 for horizontal centering and focus potentiometer (on EHT transformer) for optimum focusing. TUNER AGC 1) Check the voltage at pin lof TUNER (TP4) 2) Adjust VR402 for 1V less than maximum. SCREEN VOLTAGE 1) Set the pattern generator for grey scale. 2) Set the BCS (Brightness, Contrast, Saturation) to minumum. 3) Measure cathode voltages on the CRT base board by using a 1/1000 probe. 4) Adjust screen pot of FBT for 175 ± 2V reading on maximum cathode voltage. CRT BASEBOARD:CUT-OFF VOLTAGES AND WHITE BALANCE 1) Set the pattern generator for grey scale. 2) Set the BCS (Brightness, Contrast, Saturation) to minumum. SECAM L MODULE (L/L' AND B/G) OR (L/L' AND K1) (11SL02) 1) Set the pattern generator for the colour bar pattern at system PAL B/G and at frequency of 63.75MHz. 2) Tune the receiver for the best picture. 3) Switch pattern generator to system SECAM L and the receiver to SYS2 mode. 4) Connect the frequency counter to pin 13 of IC101. 5) Adjust VL101 for 72.3MHz reading and VR101 for no interference on the screen.
MAIN PCB FAULT FINDING GUIDE
Item
AT FIRST CHECK ALL THE SUPPLY VOLTAGES, THEN CHECK FOLLOWING RELEVANT POINTS FOR TROUBLE SHOOT!NG. TROUBLES SHOULD BE THE SAME AT ALL CHANNELS.
TROUBLE CHECK POINTS
CRT Differences
Part No. Description
11TP09D-2 CRT MODULE COMPONENT USED FOR 14-15" CRT MODELS PL902 3862021300 SOCKET CRT (MINI NECK)
COMPONENT DIFFERENCES DEPENDING ON CRT TYPES NO PICTURE, N0 SOUND .............................................. TUNER VOLTAGES, INPUT/OUTPUT SIGNALS OK Q401, 1C401 NO PICTURE, SOUND OK ............................................. INT CVBS IN, IC401, SCREEN VOLTAGE NO COLOUR ................................................................... IC401, IC402, IC403, X401 NO VERTICAL DEFLECTION ......................................... 26V, R711., PL701, IC701 VERTICAL LINEARITY .................................................... C705, VR701 VERTICAL SIZE .............................................................. R704, VR702 VERTICAL SHIFT ............................................................ VR703 VERTICAL FOLD ............................................................. 26V, R711 HORIZONTAL LINEARITY .............................................. L601, C606 HORIZONTAL SIZE ......................................................... C603, SYSTEM VOLTAGE (112V) HORIZONTAL FOLD ....................................................... SYSTEM VOLTAGE (112V) FLUE PICTURE ............................................................... TR602, G3 (FOCUS), EHT, FLAMENT VOLTAGE DARK PICTURE .............................................................. TR602 G2 (FOCUS), BRIGNES, CONTRAST VOLTAGE NOISY PICTURE ............................................................. AGC VOLTAGE, RF SIGNAL VERTICAL/HORIZONTAL SYNC. ................................... IC401 INTERFERENCE ............................................................. TUNER (TU201) NO SOUND ...................................................................... R303, IC401. (PIN5), IC301 LOW SOUND ................................................................... IC401 (PIN5, SOUND CONTROL VOLTAGE), R303, IC301 SOUND DISTORTION ..................................................... R303, IC301., 26V POP NOISE ..................................................................... Q301, C307 CONTRAST ..................................................................... IC401 (PIN25) BRIGHTNESS .................................................................. IC401 (PIN17) COLOUR .......................................................................... IC401 (PIN26) AUTO TUNING ................................................................ Q501 MEMORY ......................................................................... IC502 BAND SELECT ................................................................ IC503 NO VIDEO AT SCART ..................................................... SET AV MODE, CHECK IC401 (PIN5), (PIN6) NO SOUND AT SCART ................................................... IC401 (PIN6) MISSING CHARACTER AT TELETEXT ......................... SIGNAL AT PIN8 OF IC101 REMOTE CONTROL ....................................................... BATTERY, IR DIODE, CURRENT PATH OF IR DIODE PL902 3862021010 SOCKET CRT (NARROW NECK) C603 C606 C615 R456 R717 L601 3036227038 3033344038 3051010832 3311620437 3315610437 4091611100 CAP MKP 6.2NF 1.6KV 3.5% CAP EL 330NF 400V J CAP SER 100PF 50V J RES CF 1.6K 0W25 J RES CF 560R 0W25 J LINEARITE COIL 15" LIN COMPONENT USED WITH 14" ORION A34JLL90X23 (W) CRTS C603 C606 C615 R456 R717 L601 3032827078 3033344038 3054700836 3311220437 3311020437 4091411110 CAP MKP 7.8NF 1.6KV 3.5% CAP MKP 430NF 400V J CAP SER 47PF 50V J RES CF 1K2 0W25 J RES CF 1K 0W25 J LINEARiTE COIL 224/50uH COMPONENTS USED WITH 14" PHILIPS A34EAC01X06 CRTS C603 C606 C615 R456 R717 L601 3036227078 3033344038 3051010832 3311620437 3311020437 4091411110 4013150017 CAP MKP 6.2NF 1.6KV 3.5% CAP MKP 330NF 400V J SER 100PF 50V J RES CF 1.6K 0W25 J RES CF 1K 0W25 J LINEARTY COIL 224L/150uH LOSS COIL 150uH
COMPONENT USED WITH 14" GOLDSTAR A34KPU02XX46 CRTS C603 C606 C615 R456 R717 L601 3037527038 3034341538 3051010832 3311220437 3311020437 4090109000 CAP MKP 7.5NF 1.6KV 3.5% CAP MKP 430NF 250V J CAP SER 100PF 50V J RES CF 1K2 0W25 J RES CF 1K 0W25 J LINEARTY COIL 50uH
COMPONENT USED WITH 15" ORION A36JSW90X01 CRTS
11TP09G CRT MODULE COMPONENT USED FOR 14" CRT MODEL
Service Adjustments
The following preset adjustment procedures are not required during installation and should be made, if necessary, after servicing. WARNING EHT SHOCK HAZARD The EHT must be safely discharged before attemping to disconnect the EHT lead from the tube anode. Clip one end of a convenient lead, such as a meter lead, to the tube earthing strap on the tube body, fold back the suction cap and discharge the EHT through the lead. Press in one side of the spring clip which protects into the tube cavity to ease removal of the EHT connector. IMPORTANT Do not disturb the tube neck adjustments as these have been set for optimum performance during the tube manufacture. Before attemping the following adjustments, the receiver should be tuned with the brightness, contrast and colour controls adjusted for the best picture and all measurements are to be made after a warm-up period of approximately 5 minutes, unless stated otherwise. - 60 dBmV signal at any channel frequency - Color bar pattern and 1 KHz sound signal - Mains 220-240V AC, 50Hz
COMPONENT USED WITH 14" CAIHONG 37SX11OY22-DC05 CRTS C603 C606 C615 C901 C903 C905 C910 C911 C912 C913 C914 C915 C916 C917 C918 R456 R717 R902 R909 R916 R907 R914 R915 R921 R922 R923 R926 R931 R932 R933 L601 3038227038 3033344038 3054700836 3056810030 3055610030 3051020030 3051020030 3051020030 3051020030 CAP MKP 8.2NF 1.6KV 3.5% CAP EL 330NF 400V J CAP SER 47PF 50V J CAP SMD 680PF 50V J CAP SMD 560PF 50V J CAP SMD 1NF 50V J CAP SMD 1NF 50V J CAP SMD 1NF 50V J CAP SMD 1NF 50V J NOT CONNECTED NOT CONNECTED NOT CONNECTED CAP SMD 220PF 50V J CAP SMD 220PF 50V J CAP SMD 220PF 50V J RES CF 1.2K 0W25 J RES CF 1K 0W25 J RES SMD 150R 1/8W J RES SMD 150R 1/8W J RES SMD 150R 1/8W J RES MO 10K 2W J RES MO 10K 2W J RES MO 3.9R 3W J RES MO 10K 2W J RES SMD 150R 1/8W J RES SMD 3K3 1/8W J RES SMD 33R 1/8W J NOT CONNECTED NOT CONNECTED NOT CONNECTED LINEARITE COIL 224/50UH LOW FOCUS FBT
CPU & Adjustments
uC (MICROCONTROLLER): The microcontroller hardware that is member of the ST6 family has a TV receiver control software with menu control. It controls the chassis through IIC bus, PWM outputs and I/O ports. Dominant features of controller are control of optional teletext, outputs for OSD, IR control signal receiving, and internal EEPROM. The controller has IIC communication port at #40 , #41 and OSD driver (R,G,B,FBI) at # 22, # 23, # 24, # 25. PWM control outputs are tuning # 34; vertical linearity adjustment # 1; AGC adjustment # 2. Other control outputs are Muting - video ident # 3; led driver # 4; system switches # 5, # 6, # 8, # 19, # 20, # 36; tuner switches # 18, # 19 and inputs are AFC information from IF #9; keyboard # 10, # 11, # 13, # 14; scart mode ident (4/3-16-9) #38, #39; horizontal sync # 26; vertical # 27; infrared #35 and reset # 33.
The uC starts system according to option diodes configuration (D501, D503, D505, D506, D508). The controller has also a software which is able to control some service adjustments: R, G, B gain; R, G cut off; vertical position; vertical linearity; horizontal position; vertical amplitude; AGC; language selection for teletext. For enter to service mode followed procedure must be act within four seconds: 1 - Press volume down button on the keyboard; 2 - Press `prog' button on the R/C hand set; 3 - Press `- -` button on the R/C hand set; 4 - Press "TV" button on the R/C hand set; Parameters can be sellected by program up and down, parameter adjustments can be done by volume up and down buttons. Memorizing the adjusted parameters can be done by pressing red button. For exit from service mode Press "TV " button.
3052210030 3052210030 3052210030 3311220437 3311510830 3311510830 3311510830 3351032137 3351032137 3353993137 3351032137 3311510830 3313320830 3313300830
4090109000 4031001905
BUSH 1433
CRT Module Diagrams
Text Module Diagram
CRT Differences Tables