Text preview for : sharp - GA20 - 28JF-73.pdf part of SHARP 28JF73E SHARP GA20 SERVICE MANUAL
Back to : sharp - GA20 - 28JF-73.pa | Home
28JF-73E
SERVICE MANUAL
SE0028JF73E00
Issued: 24th Sept. 2002
GA-20 CHASSIS
PAL B/G, I / SECAM L/L', B/G, D/K SYSTEM COLOUR TELEVISION
MODEL 28JF-73EES
In the interests of user safety (required by safety regulations in some countries) the set should restored to its original condition and only parts identical to those specified should be used.
CONTENTS
ELECTRICAL SPECIFICATIONS ................... 3 IMPORTANT SERVICING NOTES ................. 4 CONTROLS & TERMINALS ........................... 5 ADJUSTMENT PROCEDURES ...................... 6 LED FLASHING CODES ............................... 12 PRINTED WIRING BOARDS ........................ 13 CHASSIS LAYOUT ......................................... 20 ICs ADDITIONAL INFORMATION .................. 22 SCHEMATIC DIAGRAMS ............................... 32 TROUBLESHOOTING TABLES ..................... 46 PARTS LISTING ............................................. 49 PACKING OF THE SET & ACCESSORIES ... 58 SOURCE OF DOCUMENTATION .................. 59
SHARP CORPORATION
1
This document has been published to be used for after sales service only.
28JF-73E
SERVICE MANUAL UPDATE LOG SHEET
Technical Report No. Technical Bulletin No. Cause / Solution Part No. Page No. Application Data /Serial No.
Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section. If you need more information, please refer to the Technical Report (Bulletin).
2
28JF-73E
ELECTRICAL SPECIFICATIONS
·Power Input .................... 220V-240 Volts AC 50Hz ·Power Consumption Normal Operation (Method IEC60107) ............ 77W Stand-by Operation ............................................ 3W ·Picture Intermediate frequency L' ................................................ 33.9MHz L, B/G, D/K,I .............................. 38.9MHz ·Sound Carrier Trap L' ................................................ 40.4MHz L, D/K ......................................... 32.4MHz B/G ............................................ 33.4MHz I .................................................. 32.9MHz ·Adjacent Sound Carrier Trap L' ................................................ 32.4MHz L, D/K, B/G ................................ 40.4MHz I .................................................. 40.9MHz ·Adjacent Picture Carrier Trap L' ................................................ 41.9MHz L, D/K, ........................................ 30.9MHz B/G ............................................ 31.9MHz ·Aerial Input Impedance VHF/UHF ................. 75 ohm Unbalanced ·Tuning Ranges ..... 45.75MHz thru 855.25 MHz VHF: IR A - J / S1 - S41 CH (Hiperband) UHF: I21 - I69 CH CATV Special Channels
·Audio Power Output Rating (MPO) / Impedance Internal Left Speaker ................................. 10W, 7 Internal Right Speaker .............................. 10W, 7 ·Speakers Left / Right ................................................. 13 x 6cm ·Convergence (Maximum Misconvergence) Static (Centre) between any two colours ... 0.08 cm Dynamic after static equals zero Within 10cm (4") circle ....................... 0.12cm 10-25cm (4-10" ) circle ...................... 0.20 cm Everywhere else ................................ 0.28 cm ·Focus ................................. High Bi-Potential Electrostatic ·Sweep Deflection ................................................ Magnetic
·White Level Set brightness control to get total picture tube cathode current of 600 µA under no signal condition. Maximum necessary correction of each picture tube cathode current to get 8550 degrees K+1 MPCD screen temperature should not exceed 15% of its original value. X=0.290 ± 0.015 Y=0.300 ± 0.015
Specifications are subject to change without prior notice.
MODEL DESTINATION (Operation Manual languages). 28JF-73E: Deutsch, Franēais, Nederlands. 28JF-73EES: Espańol, Portuguźs.
WARNING The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service personnel.
3
28JF-73E
IMPORTANT SERVICING NOTES
Only qualified service personnel are allowed to carry out maintenance and repair of this receiver.
Servicing of High Voltage System and CRT
It is important that the static charge is removed from the high voltage system when carrying out work on the receiver. This can be achieved by connecting a 10K resistor (with a suitably insulated lead) from the CRT cavity connector to the CRT ground tag. This must be carried out with the AC supply disconnected from the receiver. Note the following: · The CRT in this receiver employs Integral Implosion Protection. · If the CRT has to be changed it MUST be replaced with the correct type for continued safe working. · DO NOT lift the CRT by its neck. · When handing the CRT, ensure that shatterproof goggles are worn. · Ensure that the CRT is discharge before handling.
X-Ray
This receiver is designed to keep any x-ray emission to an absolute minimum. Some fault conditions and servicing procedures may produce potentially hazardous x-ray radiation levels. This is a problem when in close proximity to the receiver for long periods of time. To reduce any risks associated with this, please observe the following precautions: 1. When undertaking any servicing on this chassis, DO NOT increase the EHT to more than 32.5 KV, (at a instantaneous beam current of 1500µA ). 2. Ensure that during normal operation the EHT does not exceed 30.0 KV±1.5KV (at a beam current of 1700µA). This level has been preset in the factory. Always check that this level has not been exceeded after carrying out any repair on the receiver. 3. DO NOT replace the CRT with any other type than that specified in the parts listing as this may cause excessive x-ray radiation.
Before returning the receiver to the customer
In addition to the above checks, the following should also be carried out before returning the receiver to the customer. 1. Inspect all the leads to ensure that they are dressed correctly and that they are not obstructed or pinched by any other parts. 2. Ensure that all protective devices are in good condition. These will include nonmetallic control knobs, insulating fish papers, cabinets backs, compartment covers or shields, mechanical insulators, etc.
4
28JF-73E
CONTROLS & TERMINALS
HOW TO OPEN THE DOOR
Lift the projection at the lower right of the door with your finger in the direction of the arrow.
8
)URQW 79
0DLQ SRZHU EXWWRQ 3RZHU LQGLFDWRU 5HPRWH &RQWURO VHQVRU
1
2
3
%HKLQG WKH GRRU
9ROXPH 'RZQ EXWWRQ 9ROXPH 83 EXWWRQ &KDQQHO 'RZQ EXWWRQ &KDQQHO 8S EXWWRQ 69LGHR LQSXW WHUPLQDO 9,'(2 LQSXW WHUPLQDO 3$/6(&$0176& $8',2 LQSXW WHUPLQDO OHIW $8',2 LQSXW WHUPLQDO ULJKW +HDGSKRQH MDFN PP a RKPV
5HDU 79
SLQ ,Q2XW SLQ $XGLR9LGHR $9 :LWK 3$/6(&$0176& 9LGHR ,QSXW SLQ $XGLR9LGHR $9 :LWK 3$/6(&$0176& 9LGHR ,QSXW SLQ (XUR 6&$57 5*% :LWK 3$/6(&$0176& 9LGHR ,QSXW 5) ,QSXW $HULDO WHUPLQDO
1 2 3 4
5
28JF-73E
REMOTE CONTROL
TV Video TV 1. Stand-by button (TV) 2. Power button (VCR) 3. 0 ~ 9 digit buttons 4. Flash back button 5. GREEN button 6. RED button 7. Volume DOWN button 8. MENU button 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. REVEAL button LIST button STORE button CANCEL button HALF PAGE button RESET button Rewind/picture search reverse Play button Pause/Still button Stop button
1. 2.
19. 20.
Teletext TV
3.
Teletext
4. 5. 6.
21. 22. 23. 24.
TV Video
7.
25.
TV
26. 8. 27.
Teletext TV
19. TV/VIDEO button 20. Channel Call button 21. Single/Double entry button 22. YELLOW button 23. BLUE button 24. 25. 26. 27. Channel UP button Volume UP button Channel DOWN button Wide mode button
9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
28. 29. 30. 31.
TV /Teletext
28. CLOCK button 29. Sound mode button 30. HOLD button 31. Sound Mute button 32. TEXT/MIX/PICTURE button 33. INDEX button 34. 35. 36. 37. Channel UP button (VCR) Fast forward/picture search forward Channel DOWN button (VCR) Record button
32. 33. 34. 35. 36. 37.
TV Teletext TV Teletext Video
ADJUSTMENT PROCEDURES
All adjustments to this chassis, except for focus, are carried out in the Service Mode.
Service Mode
The Service Mode is provided to enable the engineer to correctly set up the receiver to the CRT fitted in the set. Note that these adjustments may vary from one receiver to another. To enter the Service Mode, carry out the following procedure. 1. Connect a test pattern to the antenna terminal. 2. Tune the receiver to this signal. 3. Turn the receiver off using the mains switch. 4. Press volume down and channel up buttons on the front of the receiver at the same time. 5. Keeping these buttons pressed, turn the mains on. 6. When the set starts up it will be in Service Mode. 7. Release the two buttons.
5
4
Figure 1
6
28JF-73E
· Use the channel up and down buttons to move between the options. · Use the volume control buttons to change the data. · To store the data, use the stand-by button on the remote control. · To exit the Service Mode, turn the receiver off using the mains switch. When the Service Mode is entered the following On Screen Display appears SERVICE SOFTWARE -x SW on: XXXX SW off: XXXX Hours ON: XXXX The figures displayed in the "XXXX" locations are hexadecimal representations of the number of times that particular function has been executed. For example if the hexadecimal number displayed after "SW on" was 0E4A, this would correspond to the receiver being turned on 3658 times. The figure displayed in the " -x " location is the EPROM version. X
Adjustment menu:
The following adjustments can be carried out in the Service Mode. 01. Horizontal Shift 02. East West Width 03. Pin Phase 04. Pin Amp (Amplitude) 05. Corner Amplitude 06. Corner Symmetry 07. Vertical Linearity 08. Vertical Angle 09. Vertical Bow 10. Vertical Amplitude 11. S Correction 12. Vertical Shift 13. Red Gain 14. Green Gain 15. Blue Gain 16. Red Cut Off 17. Green Cut Off 18. Blue Cut Off 19. Alter NVM Pag (Page) 20. Alter NVM Pos (Position) 21. Alter NVM Val (Value) 22. Teletext Mix Mode Contrast 23. Teletext Contrast 24. OSD Contrast 25. DVCO Adjustment (Only PAL) 26. DVCO Adjustment (Only NTSC) 27. AGC Adjustment 28. Rotation Inspection 29. Auto Installation On/Off
When in the Service Mode it is possible to access certain functions by using the teletext keys as below. · By pressing the Blue button each adjustment can be directly accessed via the remote control. Referring to the list above, press the Blue button followed by the adjustment number, this will directly access the selected adjustment. If any number above 29 is selected, the set will revert to the Service Mode entry page. To access a number less than 10, use the 0 key first, i.e. 02. · Press the Yellow button to go straight to the AGC adjustment. · Press the Green button once to enter "FACTORY VOLUME" level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. · Press the Green button twice to enter "FACTORY BALANCE" level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. · Press the Green button three times to enter "FACTORY BASS" level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. · Press the Green button four times to enter "FACTORY TREBLE" level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. · Press the Red button once to enter "FACTORY CONTRAST" level. Use volume control keys to change the setting. The adjustment is stored automatically. · Press the Red button twice to enter "FACTORY BRIGHTNESS" level. Use volume control keys to change the setting. The adjustment is stored automatically. · Press the Red button three times to enter "FACTORY COLOUR" level. Use volume control keys to change the setting. The adjustment is stored automatically. · If buttons 0 through 9 are pressed, the set will automatically go to that program number. · By pressing the Menu button, the unit will normalise Picture and Audio settings. The Auto Installation is then turned "on".
7
28JF-73E
Note that the receiver should be set to FULL MODE before carrying out any geometry adjustments. This can be achieved by pressing the widescreen mode button on the remote control until FULL MODE appears on the OSD. This can only be done out of the Service Mode. The following geometry adjustments can be carried out. Detailed instructions on how to execute these are given on the following pages. Horizontal · Horizontal Shift · E-W Width · Pin Phase · Pin Amp · Corner Amplitude · Corner Symmetry
Vertical · Vertical Amplitude · Vertical Shift · Vertical Bow · Vertical Angle · S Correction · Vertical Linearity
Just in case the TV set requires a full geometry adjustment, please proceed first with Vertical according to the above order, and after that, adjust Horizontal according to the above order. Horizontal Shift Adjust the Horizontal Shift so that the picture is centred. The effect of this adjustment is shown in figure 2. · When the volume up button is pressed, the picture moves to the right. · When the volume down button is pressed, the picture moves to the left. · Press the stand-by button on the remote control to store. E-W Width Adjust the E-W Width so that 8% over-scan is achieved. The effect of this adjustment is shown in figure 3. · When the volume up button is pressed, horizontal scanning decreases. · When the volume down button is pressed, horizontal scanning increases. · Press the stand-by button on the remote control to store. Figure 3 Pin Phase Adjust the Pin Phase so that the picture is symmetrical top and bottom. The effect of this adjustment is shown in figure 4. · When the volume up button is pressed, side pincushion changes. · When the volume down button is pressed, side pincushion changes. · Press the stand-by button on the remote control to store. Pin Amp Adjust the Pin Amp so that the picture is centred. The effect of this adjustment is shown in figure 5. · When the volume up button is pressed, side pincushion changes from pincushion to barrel shape. · When the volume down button is pressed, side pincushion changes from barrel shape to pincushion. · Press the stand-by button on the remote control to store. Figure 5
Figure 2
Figure 4
8
28JF-73E
Corner Amplitude Adjust the Corner Amplitude so that the picture is centred. The effect of this adjustment is shown in figure 6. Note: This adjustment affects to upper and lower sides. · When the volume up button is pressed, side pincushion changes from pincushion to barrel shape. · When the volume down button is pressed, side pincushion changes from barrel shape to pincushion. · Press the stand-by button on the remote control to store. Corner Symmetry Adjust the Corner Symmetry so that the picture is centred. The effect of this adjustment is shown in figure 7. Note: This adjustment affects to upper and lower sides. · When the volume up button is pressed, side pincushion changes from barrel shape to pincushion. · When the volume down button is pressed, side pincushion changes from pincushion to barrel shape. · Press the stand-by button on the remote control to store. Vertical Linearity Adjust the Vertical Linearity so that the upper and lower parts of the picture are symmetrical. The effect of this adjustment is shown in figure 8. · When the volume up button is pressed, the upper picture scanning decreases and the lower picture scanning increases. · When the volume down button is pressed, the upper picture scanning increases and the lower picture scanning decreases. · Press the stand-by button on the remote control to store. Vertical Angle Adjust the Vertical Angle so that the picture is centred. The effect of this adjustment is shown in figure 9. · When the volume up button is pressed, the vertical angle changes to right. · When the volume down button is pressed, the vertical angle changes to left. · Press the stand-by button on the remote control to store. Vertical Bow Adjust the Vertical Bow so that the picture is centred. The effect of this adjustment is shown in figure 10. · When the volume up button is pressed, the vertical bow changes to right. · When the volume down button is pressed, the vertical bow changes to left. · Press the stand-by button on the remote control to store. Vertical Amplitude Adjust the Vertical Amplitude so that 8% over-scan is achieved. The effect of this adjustment is shown in figure 11. · When the volume up button is pressed, the vertical size of the picture increases. · When the volume down button is pressed, the vertical size of the picture decreases. · Press the stand-by button on the remote control to store.
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
9
28JF-73E
S Correction Adjust the S Correction so that the picture symmetrical between the top, centre and bottom. The effect of this adjustment is shown in figure 12. · When the volume up button is pressed, the top and bottom scanning increases and the centre scanning decreases. · When the volume down button is pressed the top and bottom scanning decreases and the centre scanning increases. · Press the stand-by button on the remote control to store. Vertical Shift Adjust the Vertical Shift so that the picture is centred. The effect of this adjustment is shown in figure 13. · When the volume up button is pressed, the picture moves down. · When the volume down button is pressed, the picture moves up. · Press the stand-by button on the remote control to store. Colour Adjustments The following adjustments should only be carried out when the CRT or IC850 are replaced. G2 (screen), R-G-B Cut Off and Gain Adjustments 1. Follow the procedure below to set the G2 1.1 Tune the set to the output of a signal generator (monoscope pattern). 1.2 In the user menu, set contrast to 80/100 and brightness to 40/100 (TV normalized). 1.3 Select FULL MODE. 1.4 Enter the Service Mode. 1.5 Select RED GAIN in Service Mode. 1.6 Adjust SCREEN VR so that the OSD value (indicated on Figure 14) reaches 50h ± 8h.
XX XX XX XX XX 50 XX XX
Figure 12
Figure 13
Adjust value to 50h ± 8h
RED GAIN XX
Figure 14 2. Follow the procedure below to set the Cut Off. 2.1 Adjust G2. 2.2 Tune a white pattern. 2.3 Adjust colour to minimum. 2.4 Position colorimeter in the centre of screen. 2.5 Adjust brightness and contrast to obtain a luminance of 3 NITS. 2.6 Operate in Service Mode and select location RED CUT OFF, GREEN CUT OFF and BLUE CUT OFF, to obtain colour coordinates: X=0.290 ± 0.015 Y=0.300 ± 0.015 To increase press volume-up button and to decrease press volume down button. RED CUT OFF GREEN CUT OFF BLUE CUT OFF alter «X» coordinate. alter «Y» coordinate. alter «X» and «Y» coordinate.
3. Follow the procedure below to set the GAIN. 3.1 Using brightness and contrast buttons, select a luminance of 100 NITS.
10
28JF-73E
3.2 Operate in Service Mode and select location RED GAIN, GREEN GAIN and BLUE GAIN, to obtain colour coordinates: X=0.290 ± 0.015 Y=0.300 ± 0.015 To increase press volume-up button and to decrease press volume down button. RED GAIN alter «X» coordinate. GREEN GAIN alter «Y» coordinate. BLUE GAIN alter «X» and «Y» coordinate. 3.3 Exit Service Mode and check colour coordinates «X» and «Y» at 3 and 100 NITS. It may be necessary to repeat procedure 2 and 3 of Colour Adjustments. R-G-B Cut Off and Gain Adjustments (alternative method). In the event off a Colorimeter not being available, please follow the following procedures to obtain correct and Grey scale settings (R-G-B Cut Off and Gain). 1. In the user menu, set the picture levels to the FACTORY settings (normalised). 2. Enter the Service Mode. 3. Adjust the G2 as in the previous page procedure. 4. Set the 50, 51, 52, 53, 54 and 55 NVM positions on page 00 from the original value to 80. Store each location by pressing the stand-by button on the remote control. XX XX XX XX 5. Adjust grey scale as follows. XX XX XX XX 5.1 Select a grey scale signal, then set the Red Cut-off level to 32 and the Red-Gain to 50. 5.2 Leave the Red Cut-off and Gain as above and adjust Green and Blue Cut-off and Gain to achieve correct grey scale tracking. As with all grey scale adjustments it will be necesBLUE GAIN XX sary to readjust the settings to achieve good tracking. Note: The data to be adjusted is contained at the bottom right corner of the picture. See Figure 15. Changing NVM Data To change the data contained within the Non Volatile Memory, it is necessary to first select the page the data is stored in, then the position and finally to change the data itself. The procedure below outlines this process. 1. Press the channel up/down buttons and ALTER NVM PAG appears, use the volume up/down buttons to change this data (it is shown in hexadecimal format). 2. Press the channel up button and ALTER NVM POS appears, use the volume up/down buttons to change this data (it is shown in hexadecimal format). 3. Press the channel up button and ALTER NVM VAL appears, use the volume up/down buttons to change this data (it is shown in hexadecimal format). 4. Once this data has been set, press the stand-by button to store. 5. If another NVM value has to be changed, use the channel down button to select the page or position and repeat as necessary. Note: DO NOT change any NVM data, unless you have been advised to do so by a Sharp representative. If data is incorrectly changed, serious damage may occur to the receiver. Contrast Adjustments Three types of contrast levels can be varied as listed below: · TELETEXT MIX MODE CONTRAST · TELETEXT CONTRAST · OSD CONTRAST Use the volume up/down buttons to adjust to a suitable level, then. It is not necessary to press the stand-by button to store, data are memorized by exiting the Service Mode. Figure 15
11
28JF-73E
DVCO Adjustment (PAL) Carry out the DVCO Adjustment (PAL) as shown below: 1. Receive a Philips pattern signal. 2. While in the DVCO ADJUSTMENT (PAL) menu, press the stand-by button. 3. The adjustment will be carried out automatically and stored. DVCO Adjustment (NTSC) No adjustment required. AGC Adjustment To correctly align the Automatic Gain Control, follow the procedure outlined below: 1. Tune the set into a pattern generator on CH12. 2. Adjust the signal strength of the pattern generator to 59dB/µV (75). 3. Enter the Service Mode. 4. Enter the AGC Adjustment menu. 5. Press the stand-by button on the remote control. 6. The adjustment will be carried out and stored automatically. Rotation Inspection No adjustment required. Just to check the proper working of this user feature. It cannot be memorized and after reset the TV, the picture will appear normalized as other features. Auto Installation On/Off To return the receiver to the original Auto Installation mode, using the volume up or down button, set the Auto Installation On/Off to On. This setting is automatically stored and when the receiver is turned on the next time it will start up in Auto Installation mode.
LED FLASHING CODES
If the TV set does not work and the power indicator is flashing, follow the sequence according to the information below, as a guide to fault finding. 1. Unable to read or write into NVM: 66% ON, 33% OFF twice and OFF for a second.
On Off
2. MSP failure: 66% ON, 33% OFF for three times and OFF for a second.
On Off
3. VCT failure: 66% ON, 33% OFF for four times and OFF for a second.
On Off
12
28JF-73E
FB218WJN2 CRT UNIT PWB. Component side.
11
10
9
8
7
6
5
4
3
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10 11 12 13
FB218WJN2 CRT UNIT PWB. Copper side.
11
10
9
8
7
6
5
4
3
2
1 Y 13 12 11 10 9 8 7 6 5 4 3 2 1 0 X
13
28JF-73E
25
FB217WJN4 MOTHER UNIT PWB. Component side.
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 15
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
14
28JF-73E
FB217WJN4 MOTHER UNIT PWB. Component side.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 14
2
1 Y 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 X
15
28JF-73E
25
FB217WJN4 MOTHER UNIT PWB. Copper side.
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 17
2
1 Y 33 X 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
16
28JF-73E
FB217WJN4 MOTHER UNIT PWB. Copper side.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 16
2
1 Y 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 X
17
28JF-73E
FB270WJZZ CONTROL UNIT PWB Component side Copper side 25 25
24 24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1 X 9 8 7 6 5 4 3 2 1 0 Y X
1
0 Y
1
2
3
4
5
6
7
8
9
18
28JF-73E
FB220WJZZ DOUBLE FOCUS UNIT PWB
7
Component side
6
5
4
3
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Copper side
7 6
5
4
3
2
1 Y 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 X
19
28JF-73E
CHASSIS LAYOUT
PWB A (Mother Unit, FB217N4).
20
28JF-73E
PWB B CHASSIS LAYOUT (CRT SOCKET UNIT, FB218N2).
PWB C CHASSIS LAYOUT (FRONTAL POWER-CONTROL UNIT, FB270ZZ).
PWB D CHASSIS LAYOUT (DOUBLE FOCUS UNIT, FB220ZZ).
21
28JF-73E
6
handbook, full pagewidth
TDA9886 (IC201)
BLOCK DIAGRAM
CVAGC(pos) VIF-PLL filter VAGC (1) VPLL 19 (21) CBL RC VCO DIGITAL VCO CONTROL AFC DETECTOR 15 (16) 21 (23) REF AFC 16
external reference signal or 4 MHz crystal
TOP
TAGC
9 (8)
14 (15)
CAGC(neg)
TUNER AGC
VIF-AGC
VIF2 (18) 17 VIF-PLL SOUND TRAPS 4.5 to 6.5 MHz
2 (31) CVBS video output: 2 V (p-p) [1.1 V (p-p) without trap]
VIF1
1 (30)
TDA9885 TDA9886
(7) 8 SINGLE REFERENCE QSS MIXER INTERCARRIER MIXER AND AM DEMODULATOR MAD (4) 6 SIF AGC CAGC OUTPUT PORTS I 2C-BUS TRANSCEIVER NARROW-BAND FM-PLL DEMODULATOR AUDIO PROCESSING AND SWITCHES (3) 5
AUD DEEM
ICs ADDITIONAL INFORMATION
22
3 (1) OP1 OP2 SCL SDA 22 (24) 11 (10) 7 (5) DGND 10 (9) 12 (11) SIOMAD 4 (2) FMPLL sound intercarrier output and MAD select
SIF2
audio output
24 (27)
SIF1
23 (26)
de-emphasis network AFD CAF
SUPPLY
20 (22)
18 (20)
(6, 12, 13, 14, 17, 19, 25, 28, 29, 32) 13
VP
AGND
n.c.
MHC108
FM-PLL filter
(1) Not connected for TDA9885. Pin numbers for TDA9885HN in parenthesis.
Fig.1 Block diagram.
28JF-73E
TDA9886 (IC201)
7 PINNING PIN SYMBOL VIF1 VIF2 n.c. OP1 FMPLL DEEM AFD DGND n.c. AUD TOP SDA SCL SIOMAD n.c. n.c. n.c. TAGC REF VAGC n.c. CVBS n.c. AGND VPLL VP AFC OP2 n.c. SIF1 SIF2 n.c. n.c. TDA9886T TDA9886TS 1 2 - 3 4 5 6 7 - 8 9 10 11 12 - 13 - 14 15 16 - 17 - 18 19 20 21 22 - 23 24 - - TDA9885T TDA9885TS 1 2 - 3 4 5 6 7 - 8 9 10 11 12 - 13 - 14 15 - 16 17 - 18 19 20 21 22 - 23 24 - - DESCRIPTION TDA9885HN 30 31 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - 17 18 19 20 21 22 23 24 25 26 27 28 29 VIF differential input 1 VIF differential input 2 not connected output port 1; open-collector FM-PLL for loop filter de-emphasis output for capacitor AF decoupling input for capacitor digital ground not connected audio output tuner AGC TakeOver Point (TOP) for resistor adjustment I2C-bus data input and output I2C-bus clock input sound intercarrier output and MAD select with resistor not connected not connected not connected tuner AGC output 4 MHz crystal or reference signal input VIF-AGC for capacitor not connected composite video output not connected analog ground VIF-PLL for loop filter supply voltage AFC output output port 2; open-collector not connected SIF differential input 1 and MAD select with resistor SIF differential input 2 and MAD select with resistor not connected not connected
handbook, halfpage
VIF1 1 VIF2 2 OP1 3 FMPLL 4 DEEM 5 AFD 6 DGND 7 AUD 8 TOP 9 SDA 10 SCL 11 SIOMAD 12
MHC110
24 SIF2 23 SIF1 22 OP2 21 AFC 20 VP 19 VPLL TDA9885TS TDA9886TS 18 AGND 17 CVBS 16 VAGC (1) 15 REF 14 TAGC 13 n.c.
(1) Not connected for TDA9885TS.
Fig.3 Pin configuration for SSOP24.
23
28JF-73E
TDA7480 (IC1301,IC1302)
PIN CONNECTION (Top view)
-VCC -VCC -VCC OUT BOOTDIODE BOOT N.C. FEEDCAP FREQ SGN-GND
1 2 3 4 5 6 7 8 9 10
D96AU537B
20 19 18 17 16 15 14 13 12 11
-VCC -VCC -VCC -VCC +VCC POW VREG +VCC SIGN N.C. STBY/MUTE IN
PIN FUNCTIONS
N. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Name -VCC -VCC -VCC OUT BOOTDIODE BOOT NC FEEDCAP FREQUENCY SGN-GND IN ST-BY-MUTE NC +VCC SIGN VREG +VCC POW -VCC -VCC -VCC -VCC Function NEGATIVE SUPPLY. NEGATIVE SUPPLY. NEGATIVE SUPPLY. PWM OUTPUT BOOTSTRAP DIODE ANODE BOOTSTRAP CAPACITOR NOT CONNECTED FEEDBACK INTEGRATING CAPACITANCE SETTING FREQUENCY RESISTOR SIGNAL GROUND INPUT ST-BY/ MUTE CONTROL PIN NOT CONNECTED POSITIVE SIGNAL SUPPLY 10V INTERNAL REGULATOR POSITIVE POWER SUPPLY NEGATIVE SUPPLY (TO BE CONNECTED TO PIN 16 VIA C5) NEGATIVE SUPPLY NEGATIVE SUPPLY NEGATIVE SUPPLY
24
MSP3410G (IC301)
Sound IF1 Demodulator Preprocessing DAC
ADC
Loudspeaker Subwoofer
Sound IF2
Loudspeaker Sound Processing
I2S1 Prescale
Headphone Sound Processing DAC
Headphone
SCART1 DAC SCART1 ADC Prescale DAC
SCART2
SCART3
SCART DSP Input Select
SCART4
Source Select
I2S2
I2S
25
SCART Output Select SCART2
MONO
Fig. 11: Simplified functional block diagram of the MSP 34x0G
28JF-73E
28JF-73E
MSP3410G (IC301)
SC2_IN_L SC2_IN_R ASG SC1_IN_L SC1_IN_R VREFTOP NC MONO_IN AVSS AVSS NC NC ASG SC3_IN_R SC3_IN_L ASG SC4_IN_R SC4_IN_L NC AGNDC AHVSS AHVSS NC NC
AVSUP AVSUP ANA_IN1+ ANA_IN- ANA_IN2+ TESTEN XTAL_IN XTAL_OUT TP AUD_CL_OUT NC NC D_CTR_I/O_1 D_CTR_I/O_0 ADR_SEL STANDBYQ
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 1 2 3 4 5 6 7 8 9 39 38 37 36 35 34
CAPL_M AHVSUP CAPL_A SC1_OUT_L SC1_OUT_R VREF1 SC2_OUT_L SC2_OUT_R NC NC DACM_SUB NC DACM_L DACM_R VREF2 DACA_L
MSP 34x0G
33 32 31 30 29 28 27 26
25 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
NC I2C_CL I2C_DA I2S_CL I2S_WS I2S_DA_OUT I2S_DA_IN1 ADR_DA ADR_WS ADR_CL DVSUP DVSUP NC I2S_DA_IN2 DVSS DVSS DVSS DVSUP NC NC NC RESETQ NC
DACA_R
Fig. 49: PQFP80 package
26
28JF-73E
VCT3834 (IC1001)
VSUPAF
GNDAF
VSUPD
SENSE
GNDD
VCT 38xxA/B
2
2
2
VIN CIN VOUT
4 3
Video Front-end
Comb Filter
Color Decoder
Panorama Scaler
Display Processor Pict.Improv
RSW GNDM VRD XREF
SGND
VERT EW PROT HOUT
HFLB
VRT
3
Video Back-end
RGBOUT SVM
4
RGBIN VSUPAB GNDAB
Video
8
I2C MSync Color, Prio VSync
2
Audio
AOUT AIN
3
BE
I2C Master CPU 8-bit PWM 14-bit PWM 15:1 Mux 10-bit ADC 2 Timer 2 CapCom
2
I2C
TPU 24 kB ROM 24 kB
DMA
RDY
3 kB 3 kB OSD RAM OSD
1 kB CPU RAM
Reset Logic
RESQ TEST
16 kB Text RAM
96 kB CPU ROM
31 ADB, DB, CB
VSUPS GNDS
Watchdog 24 IO Ports
12
VSUPP1 GNDP1 Pxy
Clock Oscillator
XTAL1 XTAL2
CLK20
Fig. 12: Block diagram of the VCT 38xxA/B (shaded blocks are optional)
The block diagram does not show the additional features of VCT 38xxB.
27
28JF-73E
VCT3834 (IC1001)
P35 P34 VSUPP3 GNDP3 P33 P32 P31 P30 TEST FBLIN RIN GIN BIN VPROT SAFETY HFLB P36 P37 GNDD VSUPD HOUT CLK20 VB0 VB1 VB2 VB3 VB4 VB5 VB6 VB7 VBCLK P20
VERTQ VERT EW SENSE GNDM RSW1 RSW2 SVMOUT ROUT GOUT BOUT VSUPAB GNDAB VRD XREF AIN3 AIN2 AIN1 AOUT2 AOUT1 RESQ SCL SDA XTAL1 XTAL2 VSUPS GNDS WE1Q WE2Q OE1Q OE2Q ADB18
96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 97 64 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 1 2 3 4 5 6 7 8 9 63 62 61 60 59 58 57 56 55 54 53 52 51 50
P21 P22 P23 GNDP2 VSUPP2 P24 P25 P26 P27 DISINTROM VIN4 VIN3 VIN2 VIN1 CIN2/CRIN CIN1 CBIN VSUPAF GNDAF SGND VRT VOUT P10/VIN5 P11 P12 P13 GNDP1 VSUPP1 P14 P15 P16 P17
VCT 38xxA/B
49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34
33 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
ADB17 VSUPADB GNDADB ADB16 ADB15 ADB14 ADB13 ADB12 ADB11 ADB10 ADB9 ADB8 ADB7 ADB6 ADB5 VSUPADB
DB7 DB6 DB5 DB4 GNDDB VSUPDB DB3 DB2 DB1 DB0 ADB0 ADB1 ADB2 ADB3 ADB4 GNDADB
Fig. 64: PMQFP128 package
28
28JF-73E
STV9380 (IC502)
PIN CONNECTION
-VCC -VCC -VCC OUT CFLY + CFLY BOOT VREG FEEDCAP FREQ
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
-VCC -VCC -VCC -VCCPOW + VCC POW +VCC EAout IN+ INSGND
1
PIN FUNCTIONS
Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Name -VCC -VCC -VCC OUT CFLY+ CFLYBOOT VREG FEEDCAP FREQ SGND ININ+ EA out +VCC +VCCPOW -VccPOW -VCC -VCC -VCC Negative supply Negative supply Negative supply PWM Output Flyback capacitor Flyback capacitor Bootstrap capacitor Internal voltage regulator Feed-back integrating capacitor Frequency setting resistor Signal Ground Error amplifier inverting input Error amplifier non-inverting input Error amplifier output Positive supply Positive Power supply Negative Power supply Negative supply Negative supply Negative supply Function
29
28JF-73E
STV9380 (IC502)
+VCC
100nF 100nF +VCC 16 +VCC power STV9380 TDA9380 -VCC 1000µF
15
VREG 8
Vref
-VCC Flyback generator 5 6 CFLYBOOT 7 13 _ 12 150 14 Pins 1,2,3,18,19,20 11 SGND 470pF 4.7nF 10k FREQ 100nF -VCC FEEDCAP 9 10 17 -VCC power 1000µF 560pF 4 Modulator Output drive OUT 1mH 470nF 150 + Cboot 220nF CFLYBACK 100µF
Figure 1. Test and Application Circuit
100nF
Flyback detection
CFLY+
IN+
30
-VCC
1k
IN -
Input signal
EA out
Deflect. Yoke*
200
10k
1k
Sense resistor
0.5
* Deflection yoke characteristics: R = 5.5, L = 7mH
fvert = 50Hz
28JF-73E
TEA1507 (IC701)
Block Diagram
h
VCC
1
SUPPLY MANAGEMENT internal UVLO start supply
START-UP CURRENT SOURCE clamp VALLEY
8
DRAIN HVS n.c.
7
GND
2
S1
M-level VOLTAGE CONTROLLED OSCILLATOR 4 LOGIC 100 mV OVERVOLTAGE PROTECTION DEM
FREQUENCY CONTROL
OVERTEMPERATURE PROTECTION 3 -1
LOGIC
DRIVER Iss
6
DRIVER
CTRL
POWER-ON RESET
LEB S Q blank soft start S2
0.5 V
2.5 V burst detect
UVLO
R
Q 5 OCP Isense
TEA1507
MAXIMUM ON-TIME PROTECTION
short winding
0.75 V OVERPOWER PROTECTION
MGU230
PINNING SYMBOL PIN VCC GND CTRL DEM Isense DRIVER HVS DRAIN 1 2 3 4 5 6 7 8 ground control input input from auxiliary winding for demagnetization timing, OVP and OPP programmable current sense input gate driver output high voltage safety spacer, not connected drain of external MOS switch, input for start-up current and valley sensing Fig.3 Pin configuration. DESCRIPTION supply voltage
handbook, halfpage
VCC 1 GND 2
8 DRAIN 7 HVS
TEA1507
CTRL 3 DEM 4
MGU231
6 DRIVER 5 Isense
31
28JF-73E
DESCRIPTION OF SCHEMATIC DIAGRAMS
SAFETY NOTE: 1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING.
NOTE: 1. The unit of resistance « ohm »is omitted (K=1000 ohms. M= Megaohm). 2. All resistors are 1/8 watt. unless otherwise noted. 3. All capacitors are µF, unless otherwise noted (P= µµF).
IMPORTANT SAFETY NOTE: PARTS MARKED WITH « ! » ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.
SERVICE PRECAUTION: THE AREA ENCLOSED BY THIS LINE ( ) IS DIRECTLY CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK.
CAUTION This circuit diagram is original one, therefore there may be slight difference from yours.
Waveform Measurement Condition:
1. Test Equipment: DIGITAL SYNCHROSCOPE (LECROY). 2. Test Conditions: CH-12; COLOUR BARS; 70dB FROM RF INPUT 3. TV Condition: PICTURE AND AUDIO : SETTINGS ! FACTORY PRESETS
Waveform:
1
Pin1 Vp-p= 2.9V
2
Pin2 Vp-p= 2.9V
3
Pin3 Vp-p= 3.0V
32
28JF-73E
4
Pin4 Vp-p= 105V
5
Pin5 Vp-p= 100V
6
Pin6 Vp-p= 110V
7
Pin7 Vp-p= 0.8V
8
Pin8 Vp-p= 225V
9
Pin9 Vp-p=1200V
10
Pin10 Vp-p= 0.4V
11
Pin11 Vp-p= 2.0V
12
Pin12 Vp-p= 0.5V
13
Pin13 Vp-p=5.6V
14
Pin14 Vp-p= 62V
15
Pin15 Vp-p= 1.3V
33
28JF-73E
16
Pin16 Vp-p= 9.2V
17
Pin17 Vp-p= 0.24V
18
Pin18 Vp-p= 9.6V
19
Pin19 Vp-p= 0.2V
20
Pin20 Vp-p= 9.2V
21
Pin21 Vp-p= 1.4V
22
Pin22 Vp-p= 1.4V
23
Pin23 Vp-p= 0.7V
24
Pin24 Vp-p= 500V
34
28JF-73E
SCHEMATIC DIAGRAM OF CRT UNIT (FB218N2)
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
35
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 1 (FB217N4)
I
H
G
F
E
D
C
B
Page 37
A
1
2
3
4
5
6
7
36
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 1 (FB217N4)
I
H
G
F
E
D
C
B
Page 36
A
8
9
10
11
12
13
14
37
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 2 (FB217N4)
I
H
G
F
E
D
C
B
Page 39
A
1
2
3
4
5
6
7
38
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 2 (FB217N4)
I
H
G
F
E
D
C
B
Page 38
A
8
9
10
11
12
13
14
39
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 3 (FB217N4)
I
H
G
F
E
D
C
B
Page 41
A
1
2
3
4
5
6
7
40
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 3 (FB217N4)
I
H
G
F
E
D
C
B
Page 40
A
8
9
10
11
12
13
14
41
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 4 (FB217N4)
I
H
G
F
E
D
C
B
Page 43
A
1
2
3
4
5
6
7
42
28JF-73E
SCHEMATIC DIAGRAM OF MAIN 4 (FB217N4)
I
H
G
F
E
D
C
B
Page 42
A
8
9
10
11
12
13
14
43
28JF-73E
SCHEMATIC DIAGRAM OF CONTROL UNIT (FB270ZZ)
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
44
28JF-73E
SCHEMATIC DIAGRAM OF DOUBLE FOCUS UNIT (FB220ZZ)
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
45
28JF-73E
TROUBLESHOOTING TABLES
12 3,&785(
6QRZ QRLVH LQFUHDVH
<(6
'RHV WKH VQRZ QRLVH DSSHDU RQ WKH &57 DW PD[ FRQWUDVW DQG EULJKWQHVV FRQWURO"
12
1R 6QRZ QRLVH
'RHV 9 DSSHDU DW SLQ RI 78WXQHU
12
&KHFN /' DQG 5
&KHFN SLQ DQG RI ,&
$EQRUPDO
<(6
&KHFN 78 DQG WKHLU SHULSKHUDO SDUWV
1RUPDO 1RLVH RU VLJQDO DSSHDU
&KHFN 78WXQHU 6) DQG 3HULSKHUDO SDUWV
&KHFN SLQ RI ,& 'RHV QRLVH RU VLJQDO DSSHDU" <(6 6LJQDO
12 1RLVH
&KHFN ,&4 DQG WKHLU 3HULSKHUDO FLUFXLWV
&KHFN ,& 5*% RXWSXW 1RUPDO"
12
&KHFN ,&DQG WKHLU 3HULSKHUDO FLUFXLWV
<(6
&KHFN 5+HDWHU * FRQQHFWLRQ DQG SHULSKHUDO FLUFXLWV RI 7)%7 DQG &57
<(6
&KHFN SLQ DQG RI ,& 6LJQDO RU 1RLVH"
12
&KHFN &- FRQQHFWLRQ ,& DQG WKHLU 3HULSKHUDO FLUFXLWV
46
NO FUNCTION(NO SOUND AND NO PICTURE)
GREEN
Is D1011 (LED) on a light? RED
No Light Is LED FLASHING? NO
No Input Pulse
Check IC1001 94pin INPUT
Check Vertical Circuit YES
Check C755 voltage Completely 0V
Normal
Check Q1012, D1016 and SP wire"SS"connection
47
Check C752 Voltage Check C715 Voltage
Refer to"No Picture", trouble shooting
Immediately appear approx.145V, and turn to 0V soon
Check IC1001, IC1003,IC301,IC201 TU201(Refer to LED FLASHING CODES) LED FLASHING CODES If the TV set does not work and the stereo led is flashing,follow the sequence according to the information below,as a guide to fault finding. 1.Unable to read or write into NMV(IC1003):66%ON,33%OFF twice and OFF for a second.
0V
0 V
Check D754 and IC751 Immediately appear approx.8V,and turn to 0V soon Approx. 320 V
Check R718, F2001 and "AA"connection
2.MSP (IC301) failure:66%ON,33%OFF for three times and Off for a second.
Check IC701, Q702 and T703 Check D752, D753 C756,C757 and IC752
3.VCT ( IC1001) failure:66%ON,33%OFF for four times and OFF for a second.
28JF-73E
28JF-73E
12 6281'
&KHFN VRXQG VHWWLQJ E\ 5& 6LJQDO VKRXOG EH UHFHLYHG
9
&KHFN && 9ROWDJH
&KHFN // ' DQG '
$SSUR[ 99
&KHFN ,&,& $QG VSHDNHU
NO VERTICAL SCAN
Abnormal
Check the voltage at pin(15)(1) of IC502
Check D601,D605, R608 and R614
Normal approx.±14V
Abnormal
Check vertical trigger pulse at pin(12)(13) of IC502
Check IC1001 and peripheral parts Normal
Check IC502 and related circuits
48
28JF-73E
PARTS LISTING
REPLACEMENT PARTS
Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified by in the Replacement Parts Listing. ! The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended is not permitted. Replacement parts not shown in this service manual may create shock fire, or other hazards.
HOW TO ORDER REPLACEMENT PARTS
To have your order completed promptly and correctly please supply the following information. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION 5. CODE 6. QUANTITY
MARK *: REF No.
SPARE PARTS PARTS
VB66ERF022W2E RCILG0417BMZZ RCILG0443CEZZ LHLDC3009CEFN LHLDW1514BM00 QEARC0022BMZZ
DELIVERY SECTION DESCRIPTION
28"FLAT50Hz MK2 W66ERF022X013nonDAF PHIL DEGUSS.COIL ATN01121951 28"16:9 NUCTOR ROTATION COIL TOTOKU MQB1020505 ADG COIL HOLDER HOLDER UNEX 2233 C.ERATH DA-50W
* SN CODE EX CODE
S S S S S S CD AQ AD AA AA AP CX AX AM AB AA AZ
PICTURE TUBE
! !
Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q
REF No.
0604 0701 0702 0703 0704 0751 0752 0753 0754 0755 0756 0759 0762 1006 1007 1008 1009 1010 1011 1012 1013 1301 1302 1303 1304 1305
VS2SA1246//1E VS2SC2412KQ-1 VSSPA07N60C-1 VSSTP4NC80Z1E VS2SC3198-G-1 VS2SC2412KQ-1 VS2SA1037KQ-1 VS2SA1037KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SA1037KQ-1 VS2SC3198-G-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SA1037KQ-1 VSDTC314TK/-1 VS2SA1037KQ-1 VS2SA1037KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1
PARTS
TRT A1246 SANYO TRT 2SC2412 ROHM FET SPA07N60C2.A INFINEON MOS FET STP4NC80ZFP TOMEN TRT 2SC3198(AT) KOREA TRT 2SC2412 ROHM TRT BC807 SMD TRT BC807 SMD TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT BC807 SMD TRT 2SC3198(AT) KOREA TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT BC807 SMD TRT DTC314TKT146 ROHM TRT BC807 SMD TRT BC807 SMD TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM
DESCRIPTION
S S S S S S S S S S S S S S S S S S S S S S S S S S
* SN CODE EX CODE
AA AA AD AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AM AH AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA
PWB-A PWB-B PWB-C PWB-D
DUNTKB217CJW0 DUNTKB218BMV3 DUNTKB220BMV2 DUNTKB270BMV1
PRINTED WIRING BOARDS (Not replacement item)
ADJUST CHASSIS 28JF73E CRT UNIT INS HAND 28JF74H DF INS HAND 28JF73/74H CONTROL INS HAND 28JF73/74H
S S S S
BR AU AG AU
CH BF AT BF
PWB-A
TU 0201 VTUCTF5511+++
MOTHER UNIT
TUNER THOMSON
TUNER
S AN
AZ
! !
IC 0201 IC 0301 IC 0302 IC 0501 IC 0502 IC 0701 IC 0702 IC 0703 IC 0751 IC 0752 IC 0753 IC 1001 IC 1002 IC 1003 IC 1004 IC 1006 IC 1007 IC 1301 IC 1302
RH-IX1808BMZZ RH-IX1853BMZZ VHIM5218L//-1 VHIUPC358C/-1 VHISTV9380+-1 VHITEA1507/-1 RH-FX0008GEZZ RH-FX0008GEZZ VHIPQ05RD08-1 VHIKA78S05P-1 VHIKA7808AP-1 RH-IXA186WJZZ CH-IX1841CJE9 VHIBR24C64F-1 VHIMM1503XN-1 VHIBA033LBS-1 VHIBA033LBS-1 VHITDA7480/-1 VHITDA7480/-1
IC TDA9886ST PHILIPS IC MSP3410G-QA-B8 MICRONAS IC M5218L IC UPC358C NEC IC STV9380 V OUT ST IC TEA1507P/N1 PHILIPS P/COUPLER RANK-S SHARP P/COUPLER RANK-S SHARP IC PQ05RD08 SHARP IC KA78S05P KOREA IC KIA7808API KOREA ELECTRONICS IC VCT3834A MICRONAS EPROM SET 4M 3V FLASH 28JF73E NVM ROHM 64KBIT BR24C64 IC MM1503XNRE MITSUMI IC BA033LBSG 3,3V REG ROHM IC BA033LBSG 3,3V REG ROHM IC TDA7480 THOMSON IC TDA7480 THOMSON
INTEGRATED CIRCUITS
S S S S S S S S S S S S S S S S S S S
AG AR AA AE AE AC AA AA AC AA AA AW AM AC AA AB AB AF AF
AS BC AD AE AP AH AD AD AH AD AE BH AY AH AE AF AF AK AK
Q Q Q Q Q Q Q Q Q Q Q Q Q
0201 0202 0203 0206 0301 0302 0303 0304 0305 0306 0601 0602 0603
VS2SA1037KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SA1037KQ-1 VSDTC314TK/-1 VSDTC314TK/-1 VSDTC314TK/-1 VSDTC314TK/-1 VS2SC2482//-1 VS2SC5450//1E VS2SD1830//1E
TRT BC807 SMD TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT BC807 SMD TRT DTC314TKT146 ROHM TRT DTC314TKT146 ROHM TRT DTC314TKT146 ROHM TRT DTC314TKT146 ROHM TRT 2SC2482 TOSHIBA TRT 2SC5450-SH4-RG SANYO TRT S2D1830-CB11 SANYO
TRANSISTORS
S S S S S S S S S S S S S
AA AA AA AA AA AA AA AA AA AA AA AF AB
AA AA AA AA AA AA AB AB AB AB AC AQ AF
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D
0201 0202 0203 0204 0205 0206 0301 0302 0303 0304 0305 0306 0307 0308 0309 0310 0311 0312 0313 0314 0315 0401 0402 0403 0404 0405 0406 0407 0408 0409 0410 0411 0412 0413 0414 0503 0601 0602 0603 0604 0605 0606 0607 0608 0701 0703
RH-DX0551BMZZ RH-EX0546BMZZ RH-EX0546BMZZ RH-DX0623BMZZ RH-DX0623BMZZ RH-DX0623BMZZ RH-EX0549BMZZ RH-EX0549BMZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX0546BMZZ RH-EX0546BMZZ RH-EX1398CEZZ RH-EX1398CEZZ RH-EX0546BMZZ RH-EX0546BMZZ RH-EX0544BMZZ RH-EX0549BMZZ RH-EX1394CEZZ RH-EX0549BMZZ RH-EX0549BMZZ RH-EX0549BMZZ RH-EX0549BMZZ RH-EX0549BMZZ RH-EX1394CEZZ RH-EX0556BMZZ RH-EX0549BMZZ RH-EX1394CEZZ RH-DX0487CEZZ RH-DX0295CEZZ RH-DX0514CEZZ RH-DX0229CEZZ RH-DX0302CEZZ RH-DX0295CEZZ RH-EX0673GEZZ RH-DX0487CEZZ RH-EX0630GEZZ RH-DX0551BMZZ RH-DX0555BMZZ
DIODE LL4148 TFK SMD ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC5V6 TFK SMD DIODE BA591 SMD PHILIPS DIODE BA591 SMD PHILIPS DIODE BA591 SMD PHILIPS ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE UDZSTE-178.2B WAKO ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC4V7 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODO TZMC15 TFK SMD ZENER DIODE TZMC7V5 TFK SMD ZENER DIODE UDZSTE-175.6B WAKO DIODE 1SR153-400T-31-A ROHM DIODE RU3AM LF-A5 600V/1.5A/0.4 SANKEN DIODE RS3FS PREFOR SANKEN DIODE RU4AM SANKEN DIODE UZA DIODE RU3AM LF-A5 600V/1.5A/0.4 SANKEN ZENER DIODE MTZJ30DT ROHM DIODE 1SR153-400T-31-A ROHM ZENER DIODE DIODE LL4148 TFK SMD DIODE RF2005 FAGOR
DIODES
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA
AA AA AA AB AB AB AA AA AB AB AB AB AB AB AB AB AB AA AA AB AB AA AA AA AA AB AA AA AA AA AA AB AA AA AB AB AC AF AA AB AC AA AB AA AA AB
49
28JF-73E
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D
REF No.
0704 0705 0706 0707 0708 0709 0710 0711 0712 0751 0752 0753 0754 0755 0756 0757 0758 0759 0760 0761 0762 0763 0764 0765 0766 0767 0770 0773 0774 0775 0776 0780 0783 0784 0785 0786 1002 1003 1004 1005 1006 1007 1009 1010 1011 1012 1013 1014 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1301 1302 1303 1304 1305 1306
RH-DX0555BMZZ RH-DX0321CEZZ VHSSF0R5G43-1 RH-DX0321CEZZ VHD1SS244//-1 RH-DX0555BMZZ RH-EX0645GEZZ RH-DX0555BMZZ RH-DX0551BMZZ RH-EX0655GEZZ RH-DX0460CEZZ RH-DX0460CEZZ RH-DX0406CEZZ RH-DX0461CEZZ RH-IX1674BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-EX0713GEZZ RH-DX0551BMZZ RH-EX0555BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-EX0641GEZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0045BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-EX0619GEZZ RH-DX0551BMZZ RH-EX1394CEZZ RH-DX0551BMZZ RH-EX0546BMZZ RH-EX0544BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-EX0544BMZZ RH-EX1394CEZZ RH-EX0545BMZZ RH-EX0546BMZZ RH-EX0546BMZZ RH-EX0546BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0045BMZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-EX1394CEZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-DX0551BMZZ RH-EX1394CEZZ RH-DX0551BMZZ RH-DX0551BMZZ
PARTS
DIODE RF2005 FAGOR DIODE EG01CV1 SANKEN THYRISTOR SF0R5G43(N) TOSHIBA DIODE EG01CV1 SANKEN SW DIODE 1SS244T-72 DIODE RF2005 FAGOR ZENER DIODE DIODE RF2005 FAGOR DIODE LL4148 TFK SMD ZENER DIODE MTZJ20BT ROHM DIODE RU30ZLF0140-302 SANKEN DIODE RU30ZLF0140-302 SANKEN DIODE RK16V SANKEN DIODE RU4AMLF-M1 SANKEN IC KA431AZ SAMSUNG DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD ZENER DIODE MTZJ2.0A ROHM DIODE LL4148 TFK SMD ZENER DIODE TZMC13 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD ZENER DIODE MTZJ12CT ROHM DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE 1N4148 DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD ZENER DIODE 6.2V B3 DIODE LL4148 TFK SMD ZENER DIODE UDZSTE-175.6B WAKO DIODE LL4148 TFK SMD ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC4V7 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD ZENER DIODE TZMC4V7 TFK SMD ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE TZMC5V1 TFK SMD ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC5V6 TFK SMD ZENER DIODE TZMC5V6 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE 1N4148 ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO ZENER DIODE UDZSTE-175.6B WAKO DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD ZENER DIODE UDZSTE-175.6B WAKO DIODE LL4148 TFK SMD DIODE LL4148 TFK SMD
DESCRIPTION
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S
* SN CODE EX CODE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AD AD AD AA AB AA AB AA AA AD AD AD AD AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AB AB AB AB AB AB AB AB AA AA AA AB AA AA
REF No.
L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L 0201 0202 0203 0204 0301 0302 0303 0304 0305 0306 0307 0308 0309 0310 0311 0313 0315 0501 0504 0602 0603 0751 0752 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1301 1302 1303 1304 1305 1306
PARTS
VP-DF6R8K0000 VP-DF120K0000 VP-DF100K0000 VP-DF3R3K0000 VP-XF100K0000 VP-DF120K0000 VP-XF100K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-XF3R3K0000 VP-XF3R3K0000 VP-XF8R2K0000 RCILP0271BMZZ RCILZ1034CEZZ RCILZ1053CEZZ RCILP0218CEZZ VP-CF3R3K0000 VP-NM1R0MR10N VP-NM1R0MR10N VP-NM1R0MR10N VP-DF1R0K0000 VP-NM1R0MR10N VP-DF1R0K0000 VP-DF3R3K0000 VP-NM1R0MR10N VP-DF1R0K0000 VP-DF1R0K0000 VP-NM1R0MR10N RCILP0312BMZZ VP-CF3R3K0000 VP-CF3R3K0000 VP-CF3R3K0000 VP-CF3R3K0000 RCILP0312BMZZ
DESCRIPTION
PEAK COIL 6,8UH 10% PEAK COIL 12UH 10% PEAK COIL 10UH 10% PEAK COIL 3,3UH 10% PEAK COIL 10UH 10% 1/8W PEAK COIL 12UH 10% PEAK COIL 10UH 10% 1/8W PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3.3UH 10% 1/8W PEAK COIL 3.3UH 10% 1/8W PEAKING COIL 8.2M-H COIL BC-400/K DIEMEN COIL 38uH LH-16PA-34FR-T4 TAIYO YUDEN COIL 1mH 10% 0155013400-A BOB 33uH 10% FLR88-A PEAK COIL 3.3UH 10% COIL 1UH SMD COIL 1UH SMD COIL 1UH SMD PEAKING COIL 1.0 U-H COIL 1UH SMD PEAKING COIL 1.0 U-H PEAK COIL 3,3UH 10% COIL 1UH SMD PEAKING COIL 1.0 U-H PEAKING COIL 1.0 U-H COIL 1UH SMD COIL A823MY-680K=R TOKO PEAK COIL 3.3UH 10% PEAK COIL 3.3UH 10% PEAK COIL 3.3UH 10% PEAK COIL 3.3UH 10% COIL A823MY-680K=R TOKO
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AB AA AA AA AB AB AB AB AB AB AB AB AA AA AA AD AD AB AA AB AB AB AB AA AB AA AB AB AA AA AB AA AB AB AB AB AA AA AA AA AB AA AA AA AB AB AB AB AB AB AB AB AB AB AA AG AL AG AD AB AB AB AB AA AB AA AB AB AA AA AB AD AB AB AB AB AD
COILS
SF 0201 SF 0202
RFILC0294BMZZ RFILC0278BMZZ
CERAMIC FILTERS
SAW FILTER K9456 EPCOS SAW FILTER K3953M SIEMENS
S AA S AK
AA AM
! ! !
T T T T T
0601 0602 0603 0702 0703
RTRNZ0731CEZZ RTRNFA014WJZZ RCILPA033WJZZ RTRNCA003WJZZ RTRNWA022WJZZ
H-DRIVE TRANS FBT BW02862 HITACHI COIL TRANS. TRANS WA022WJ SANKEN
TRANSFORMERS
S S S S S
AB AQ AC AE AE
AG BB AH AN AP
X 0201 X 0301 X 1001 PR 0701
RCRSB0201BMZZ RCRSB0203BMZZ RCRSB0219BMZZ RMPTP0001BMZZ
CRYSTAL 4 MHZ CRYSTAL 18,432 MHZ CRYSTAL 20.25 HMZ PTC B59250-C1080-B70
PACKAGED CIRCUITS
S S S S
AK AD AG AA
AM AG AH AD
C C C C C C C C C C C C C C C C C C C C
0201 0202 0203 0204 0205 0206 0207 0209 0210 0211 0212 0213 0214 0215 0216 0217 0218 0219 0220 0223
VCEA0A1CW107M VCCCCY1HH221J VCCCCY1HH270J VCEA0A0JW477M VCKYCY1CF334Z VCEA0A0JW107M VCCCCY1HH100D VCKYCY1HB103K VCCCCY1HH391J VCKYCY1HB103K VCFYFA1HA474J VCFYFA1HA684J VCEA0A0JW227M VCFYFA1HA224J VCKYCY1HB152K VCEA0A0JW107M VCKYCY1HF223Z VCKYCY1EF104Z VCCCCY1HH100D VCKYCY1HF103Z
ELEC C 100UF 20% 16V S. CHIP CAP 220PF/50V TAPED S. CHIP CAP 27PF/50V (TAPED) E CAPACITOR 470UF/6.3V 6.3X11 S. CHIP CAP. 0.33UF/16V TAPED ELEC C 100UF 20% 6,3V S. CAPACITOR 10PF/50V GRM39B 103K 50 (1608)SMD CAPACITOR GRM39CK 391J 50 (1608)SMD CAPACITOR GRM39B 103K 50 (1608)SMD CAPACITOR FILM CAPACITOR 474 MAT POL FILM C 680NF 5% 50V E CAPACITOR 220UF/6.3V-5X11 PP FILM C 220NF 5% 50V GRM39B 152K 50 (1608)SMD CAPACITOR ELEC C 100UF 20% 6,3V SC CAPACITOR 0.022UF 50V TAPED S CHIP TAPE CAP 0.1UF/25V S. CAPACITOR 10PF/50V CHIP CAP 0.01UF/50V
CAPACITORS
S S S S S S S S S S S S S S S S S S S S
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA
50
28JF-73E
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
REF No.
0225 0226 0227 0228 0229 0230 0232 0233 0234 0301 0302 0303 0304 0305 0306 0307 0308 0309 0310 0311 0312 0313 0314 0315 0317 0318 0319 0320 0321 0322 0323 0324 0325 0326 0327 0328 0329 0330 0331 0332 0337 0338 0343 0344 0345 0346 0347 0348 0349 0350 0351 0352 0353 0354 0355 0356 0357 0358 0360 0362 0363 0364 0365 0366 0367 0368 0369 0370 0371 0372 0373 0374 0375 0376
VCEA0A1CW106M VCKYCY1HB103K VCCCCY1HH220J VCCCCY1HH220J VCEA0A1HW106M VCKYCY1HB102K VCKYPA1HF103Z VCKYPA1HF103Z VCCCCY1HH270J VCKYCY1EF104Z VCKYCY1EF473Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCEA0A1CW106M VCEA0A1CW106M VCEA0A1CW106M VCEA0A1CW106M VCKYCY1EF104Z VCEA0A1CW337M VCEA0A1CW106M VCEA0A1CW106M VCEA0A1HW335M VCKYCY1EF104Z VCFYFA1HA334J VCFYFA1HA334J VCFYFA1HA334J VCFYFA1HA334J VCEA0A1CW106M VCKYCY1EF104Z VCKYCY1EF104Z VCCCCY1HH470J VCCCCY1HH470J VCCCCY1HH5R0C VCCCCY1HH470J VCCCCY1HH5R0C VCKYCY1EF104Z VCEA0A0JW227M VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH681J VCCCCY1HH681J VCFYFA1HA334J VCFYFA1HA334J VCEA0A1EW107M VCEA0A1EW107M VCKYCY1CF224Z VCKYCY1CF224Z VCKYCY1HB102K VCKYCY1HB102K VCFYFA1HA334J VCFYFA1HA334J VCKYCY1HB102K VCKYCY1HB102K VCEA0A0JW227M VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCKYCY1HB102K VCKYCY1HB102K VCEA0A1CW106M VCEA0A1CW106M VCEA0A1CW106M VCEA0A1CW106M VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K
PARTS
ELEC C 10UF 20% 16V GRM39B 103K 50 (1608)SMD CAPACITOR S. CHIP CAP 22PF/50V TAPED S. CHIP CAP 22PF/50V TAPED ELEC C 10UF 20% 50V S. CHIP CAP 0.001UF/50V C.CAPACITOR 0.01U-F 50V C.CAPACITOR 0.01U-F 50V S. CHIP CAP 27PF/50V (TAPED) S CHIP TAPE CAP 0.1UF/25V C CAPACITOR 0.047UF/25V TAPED S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V S CHIP TAPE CAP 0.1UF/25V ELEC C 330UF 20% 16V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V ELEC C 3,3UF 20% 50V S CHIP TAPE CAP 0.1UF/25V POL FILM C 330NF 5% 50V POL FILM C 330NF 5% 50V POL FILM C 330NF 5% 50V POL FILM C 330NF 5% 50V ELEC C 10UF 20% 16V S CHIP TAPE CAP 0.1UF/25V S CHIP TAPE CAP 0.1UF/25V S. CHIP CAP 47PF/50V (TAPED) S. CHIP CAP 47PF/50V (TAPED) S. CAPACITOR TAPED S. CHIP CAP 47PF/50V (TAPED) S. CAPACITOR TAPED S CHIP TAPE CAP 0.1UF/25V E CAPACITOR 220UF/6.3V-5X11 S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED GRM39CK 681J 50 (1608)SMD CAPACITOR GRM39CK 681J 50 (1608)SMD CAPACITOR POL FILM C 330NF 5% 50V POL FILM C 330NF 5% 50V E. CAPACITOR 100UF 25V 6.3x11 E. CAPACITOR 100UF 25V 6.3x11 S.C.CAP 0.22UF 16V TAPED S.C.CAP 0.22UF 16V TAPED S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V POL FILM C 330NF 5% 50V POL FILM C 330NF 5% 50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V E CAPACITOR 220UF/6.3V-5X11 S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V
DESCRIPTION
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S
* SN CODE EX CODE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
!
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
REF No.
0401 0402 0406 0410 0428 0429 0430 0501 0502 0505 0506 0507 0508 0509 0510 0511 0512 0513 0514 0515 0516 0517 0518 0519 0520 0521 0526 0527 0601 0602 0603 0604 0605 0606 0607 0608 0609 0609 0610 0610 0612 0615 0616 0617 0618 0619 0620 0621 0622 0623 0701 0702 0704 0705 0706 0707 0708 0709 0710 0712 0713 0714 0715 0716 0717 0718 0751 0752 0753 0754 0755 0756 0757 0758
VCKYPA1HB103K VCFYFA1HA684J VCFYFA1HA684J VCFYFA1HA684J VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYPA1HB391K VCEA0A1VW227M VCKYPA1HB391K VCKYPA2HB102K VCEA0A1VW106M VCKYPA2HB102K VCEA0A1EW477M VCQYTA1HM104K VCQYTA1HM104K VCEA0A1EW477M VCEA0A1VW107M VCKYPA1HB471K VCKYPA1HB472K VCQYTA1HM104K VCFYFA1HA224J VCQYTA1HM104K VCKYPA1HB561K VCFYAH2AA474K VCKYCY1HB102K VCQYTA1HM683J VCQYTA1HM683J VCKYPA1HB102K VCKYPA2HB561K VCKYPA2HB102K VCEA0A1EW108M VCKYPA1HB472K RC-KZ0033CEZZ VCFYAA2EA104J VCFPGU2EC394J VCFPVC3CA752H VCFPVC3ZA752H VCFPVC3CA722H VCFPVC3ZA722H VCFPGU2EC624J VCKYPA2HB102K VCEA0A2EW106M RC-FZ0377CEZZ VCKYPA2HB102K VCEA0A1HW106M VCEA0A1EW108M VCEA0A1VW107M VCFPVC2DB224J VCQPPD2JB563J RC-KZ0029CEZZ RC-KZ0029CEZZ VCKYPA1HB102K VCEA0A1EW226M VCQYTA1HM473J RC-KZ0029CEZZ VCKYPA1HF103Z RC-KZ0296CEZZ VCFPVC3CA822H RC-KZ0038CEZZ VCQPPC2JB333K VCEA0A1HW226M RC-EZ0119BMZZ RC-KZ0106GEZZ RC-KZ0038CEZZ RC-KZ0038CEZZ VCEA0A2AW105M VCEA0A1CW108M VCQYTA1HM273J RC-EZA035WJZZ RC-EZA035WJZZ VCEA0A1EW108M VCEA0A1EW108M VCQYTA1HM104K
PARTS
CERAMIC CAPACITOR 10NF10% 50V POL FILM C 680NF 5% 50V POL FILM C 680NF 5% 50V POL FILM C 680NF 5% 50V S CHIP TAPE CAP 0.1UF/25V S CHIP TAPE CAP 0.1UF/25V S CHIP TAPE CAP 0.1UF/25V CERAM C 390PF 10% 50V ELEC C 220UF 20% 35V CERAM C 390PF 10% 50V CERAM C 1NF 10% 500V ELEC C 10UF 20% 35V CERAM C 1NF 10% 500V ELEC C 470UF 20% 25V POL FILM C 100NF 10% 50V POL FILM C 100NF 10% 50V ELEC C 470UF 20% 25V ELEC C 100UF 35V CERAM C 470PF 10% 50V CERAM C 4,7NF 10% 50V POL FILM C 100NF 10% 50V PP FILM C 220NF 5% 50V POL FILM C 100NF 10% 50V CERAM C 560PF 10% 50V PP FILM C 470NF 10% 100V S. CHIP CAP 0.001UF/50V POL FILM C 68NF 5% 50V POL FILM C 68NF 5% 50V C.CAPACITOR 1000PF/50V C CERAM 560PF 10% 500V CERAM C 1NF 10% 500V ELEC C 1000UF 20% 25V CERAM C 4,7NF 10% 50V CERAM C 150PF 2KV MURATA POL FILM C 100NF 5% 250V PP FILM C 390NF 5% 250V PP FILM C 7,5NF 3% 1.6KV (DKRG) PP FILM C 7,5NF 3% 1.8KV (DKRG) PP FILM C 7,2NF 3% 1.6KV (DKRG) PP FILM C 7,2NF 3% 1.8KV PP FILM C 620NF 5% 250V (FGSM) CERAM C 1NF 10% 500V ELEC C 10UF 20% 250V PP FILM C 4,7uF 63V CERAM C 1NF 10% 500V ELEC C 10UF 20% 50V ELEC C 1000UF 20% 25V ELEC C 100UF 35V PP FILM C 220NF 5% 200V POL FILM C CERAM C 10NF 80,20% 250V CERAM C 10NF 80,20% 250V C.CAPACITOR 1000PF/50V ELEC C 22UF 20% 25V FILM POL C 47NF 5% 50V CERAM C 10NF 80,20% 250V C.CAPACITOR 0.01U-F 50V CERAM C 470PF 2KV MURATA PP FILM C 8,2NF 3% 1.6KV CERAM C 470PF 2KV POL FILM C 33NF 10% 630V ELEC C 22UF 20% 50V C ELEC 220uF 385V B43303-H227-M SIEMENS CERAM C DE1410 E332M-KX CERAM C 470PF 2KV CERAM C 470PF 2KV ELEC C 1UF 20% 100V ELEC C 1000MF 16V 10X16MM F. CAPACITOR 0.027 U-F ELEC C 100UF 200V LOW INPEDANCE ELEC C 100UF 200V LOW INPEDANCE ELEC C 1000UF 20% 25V ELEC C 1000UF 20% 25V POL FILM C 100NF 10% 50V
DESCRIPTION
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S
* SN CODE EX CODE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AB AA AA AB AA AA AA AA AA AA AC AC AA AA AA AC AA AA AA AA AA AA AF AB AA AA AA AA AA AB AB AA AA AA AA AB AB AB AA AA AA AA AA AA AA AA AA AB AA AA AB AA AA AA AA AA AA AA AD AA AA AA AA AA AA AC AA AB AC AE AC AC AC AC AE AA AB AE AA AA AC AA AB AC AC AC AA AA AA AC AA AB AD AB AC AA AR AC AB AB AA AB AA AF AF AC AC AA
51
28JF-73E
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
REF No.
0760 0764 0766 0767 0768 0769 0771 0772 0773 0774 0775 0780 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1029 1030 1031 1032 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1047 1048 1049 1050 1057 1058 1059 1060 1061 1065 1067 1068 1301 1302 1303 1304 1305 1306 1307
VCEA0A1CW106M VCEA0A1CW476M VCEA0A1EW476M VCKYCY1HB103K VCEA0A1CW476M VCEA0A1HW106M VCEA0A1EW476M VCEA0A1CW476M VCEA0A1HW105M VCE9EA1HW105M VCEA0A1HW106M VCKYCY1HF103Z VCKYCY1EF104Z VCKYCY1HB103K VCEA0A1CW106M VCEA0A1CW227M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1HB222K VCKYCY1EF104Z VCKYCY1EF473Z VCEA0A1HW106M VCKYCY1HB271K VCKYCY1HB222K VCKYCY1CF474Z VCEA0A1CW476M VCCCCY1HH101J VCCCCY1HH101J VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1HB222K VCEA0A0JW477M VCKYCY1HB222K VCKYCY1EF104Z VCEA0A1CW476M VCEA0A0JW477M VCKYCY1HB222K VCKYCY1EF104Z VCKYCY1EF104Z VCCCCY1HH101J VCCCCY1HH101J VCKYCY1HB103K VCKYCY1HB102K VCKYCY1HB103K VCEA0A1CW477M VCKYCY1EF104Z VCEA0A1HW335M VCKYCY1CF474Z VCCCCY1HH3R0C VCCCCY1HH5R0C VCKYCY1CF474Z VCKYCY1EF104Z VCFYFA1HA684J VCKYCY1EF104Z VCE9EA1CW106M VCKYCY1HB103K VCKYCY1HB103K VCCCCY1HH101J VCKYCY1HB103K VCEA0A1CW476M VCKYCY1HB103K VCEA0A1AW477M VCKYCY1HB103K VCKYCY1CF224Z VCKYCY1HF103Z VCKYPA1HF103Z VCKYTV1HF103Z VCCCCY1HH101J VCEA0A1EW227M VCKYCY1EF104Z VCKYTV1HF104Z VCKYCY1HB561K VCKYCY1HB472K VCFYFA1HA474J
PARTS
ELEC C 10UF 20% 16V ELEC C 47UF 20% 16V ELEC C 47UF 20% 25V GRM39B 103K 50 (1608)SMD CAPACITOR ELEC C 47UF 20% 16V ELEC C 10UF 20% 50V ELEC C 47UF 20% 25V ELEC C 47UF 20% 16V ELEC C 1UF 20% 50V E CAPACITOR 1UF 50V NP ELEC C 10UF 20% 50V CHIP CAP 0.01UF/50V S CHIP TAPE CAP 0.1UF/25V GRM39B 103K 50 (1608)SMD CAPACITOR ELEC C 10UF 20% 16V E CAPACITOR 220UF 16V 6.3x11 S CHIP TAPE CAP 0.1UF/25V S CHIP TAPE CAP 0.1UF/25V S CHIP CAPACITOR 0.0022UF/50V TAPED S CHIP TAPE CAP 0.1UF/25V C CAPACITOR 0.047UF/25V TAPED ELEC C 10UF 20% 50V GRM39B 271K 50 (1608)SMD CAPACITOR S CHIP CAPACITOR 0.0022UF/50V TAPED GRM39F 474Z 16 (1608)SMD CAPACITOR ELEC C 47UF 20% 16V S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED S CHIP TAPE CAP 0.1UF/25V S CHIP TAPE CAP 0.1UF/25V S CHIP CAPACITOR 0.0022UF/50V TAPED E CAPACITOR 470UF/6.3V 6.3X11 S CHIP CAPACITOR 0.0022UF/50V TAPED S CHIP TAPE CAP 0.1UF/25V ELEC C 47UF 20% 16V ELEC C 470UF 20% 6,3V S CHIP CAPACITOR 0.0022UF/50V TAPED S CHIP TAPE CAP 0.1UF/25V S CHIP TAPE CAP 0.1UF/25V S. CHIP CAP 100PF/50V TAPED S. CHIP CAP 100PF/50V TAPED GRM39B 103K 50 (1608)SMD CAPACITOR S. CHIP CAP 0.001UF/50V GRM39B 103K 50 (1608)SMD CAPACITOR ELEC C 470UF 20% 16V S CHIP TAPE CAP 0.1UF/25V ELEC C 3,3UF 20% 50V GRM39F 474Z 16 (1608)SMD CAPACITOR S C CAPACITOR (TAPED) S. CAPACITOR TAPED GRM39F 474Z 16 (1608)SMD CAPACITOR S CHIP TAPE CAP 0.1UF/25V POL FILM C 680NF 5% 50V S CHIP TAPE CAP 0.1UF/25V E CAPACITOR 10UF 16V NP GRM39B 103K 50 (1608)SMD CAPACITOR GRM39B 103K 50 (1608)SMD CAPACITOR S. CHIP CAP 100PF/50V TAPED GRM39B 103K 50 (1608)SMD CAPACITOR ELEC C 47UF 20% 16V GRM39B 103K 50 (1608)SMD CAPACITOR E.CAPACITOR 470UF 10V 6.3x11 GRM39B 103K