Text preview for : SyncMaster 753s Manual SERVICE.pdf part of samsung SyncMaster 753s printed circuit diagram
Back to : SyncMaster 753s Manual SE | Home
CONFIDENTIAL
COLOR MONITOR
Chassis AN17K* AN17L* Model 753DFX, 76DF 753v, 753s 76V, 76E
SERVICE
COLOR MONITOR
Manual
CONTENTS
1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignment & Adjustments 5. Troubleshooting 6. Exploded View & Parts List
AN17KS/AN17LS
7. Electrical Parts List 8. Block Diagram 9. Wiring Diagram 10. Schematic Diagrams
AN17KT/AN17LT
CONFIDENTIAL
1 Precautions
1-1 Safety Precautions
WARNINGS 1. For continued safety, do not attempt to modify the circuit board. 2. 3. Disconnect the AC power before servicing. When the chassis is operating, semiconductor heatsinks are potential shock hazards. 3. 2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.
(READING SHOULD NOT BE ABOVE 0.5mA)
1-1-1
Servicing the High Voltage and CRT :
WARNING: A high voltage VR replaced in the wrong direction may cause excessive X-ray emissions. 1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. When troubleshooting a monitor with excess HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage. High voltage should always be kept at the rated value (not higher). Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode. Do not lift the CRT by the neck.
4.
2.
3.
4.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES
LEAKAGE CURRENT TESTER
5.
2-WIRE CORD
6.
ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
EARTH GROUND
7.
Figure 1-1. Leakage Current Test Circuit
1-1-2
Fire and Shock Hazard
1-1-3 Product Safety Notices
Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment.
Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor.
AN17K*/AN17L*
1-1
1 Precautions
CONFIDENTIAL
1-2 Servicing Precautions
WARNING 1:First read the "Safety Precautions" section of this manual. If unforeseen circumstances create conflict between the servicing precautions and safety precautions, always follow the safety precautions. WARNING 2:A high voltage Micom control replaced in the wrong direction may cause excessive Xray emissions. WARNING 3:An electrolytic capacitor installed with the wrong polarity might explode.
1. 2. Servicing precautions are printed on the cabinet, and should be followed closely. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
6.
3.
4.
8.
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESDs. 8. 6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD. Indicates ESDs on the Schematic Diagram in this manual.
7.
2.
3.
4. 5.
9.
1-2
AN17K*/AN17L*
CONFIDENTIAL
2 Product Specifications
2-1 Specifications
Item Picture Tube Description 17-Inch (43 cm): 16-inch (40.6 cm) viewable, Flat-face, 90° Deflection, 0.20 mm (Horizontal) Dot pitch, Silica coated with anti-electrostatic properties (TCO: Multilayer coating), Medium-short persistence phosphor Horizontal : 30 kHz ~ 70 kHz Vertical : 50 Hz ~ 160 Hz Unlimited colors Horizontal : 1280 Dots Vertical : 1024 Lines Analog, 0.7 Vp-p positive at 75 , internally terminated Separate Sync: TTL level, positive/negative 110 MHz Horizontal : 312 mm ± 4 mm, Vertical : 234 mm ± 4 mm AC 90 ~ 264 Volts, 60 Hz or 50 Hz ± 3 Hz 90 Watt (max)
Scanning Frequency Display Colors Maximum Resolution Input Video Signal Input Sync Signal Maximum Pixel Clock rate Active Display Input Voltage Power Consumption Dimensions (W x D x H) (Net/Gross) AN17KS/AN17KT AN17LS AN17LT Weight (Net/Gross) AN17KS AN17KT AN17LS AN17LT Environmental Considerations
15.7 x 16.2 x 15.7 Inches (398 x 412 x 400 mm) / 20.4 x 22.8 x 18.4 Inches (517 x 580 x 468 mm) 15.7 x 16.2 x 15.7 Inches (398 x 412 x 400 mm) / 18.3 x 20.2x 18.0 Inches (464 x 512 x 458 mm) 15.7 x 16.2 x 15.7 Inches (398 x 412 x 400 mm) / 18.3 x 20.4x 18.4 Inches (464 x 517 x 467 mm) 15.9 kg (35.1 lbs) / 18.68 kg (41.2 lbs) 16.2 kg (35.7 lbs) / 18.7 kg (41.2 lbs) 15.0 kg (33.1 lbs) / 17.5 kg (38.6 lbs) 15.0 kg (33.1 lbs) / 17.5 kg (38.6 lbs) Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C) Humidity : 10 % ~ 80 % Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %
· Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. · Designs and specifications are subject to change without prior notice.
AN17K*/AN17L*
2-1
2 Product Specifications
CONFIDENTIAL
Sync Type
2-2 Pin Assignments
Separate Red Green Blue N-C DDC Return GND-R GND-G GND-B N-C GND-Sync/Self-raster N-C DDC Data H-Sync V-Sync DDC Clock
Macintosh GND-R Red H/V Sync Sense 0 Green GND-G Sense 1 Reserved Blue Sense 2 GND V-Sync GND-B GND H-Sync
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
5
15
Figure 2-1. Male Type
Figure 2-2. Male Type
2-2
AN17K*/AN17L*
2 Product Specifications
CONFIDENTIAL
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1 Timing Chart Mode VGA2/70 Hz 720 x 400 31.469 31.777 3.813 1.907 25.422 0.636 70.087 16.683 0.064 1.080 12.711 0.413 28.322 IBM VGA3/60 Hz 640 x 480 31.469 31.778 3.813 1.907 25.422 0.636 59.940 14.268 0.064 1.048 15.253 0.318 25.175 640/75 Hz 640 x 480 37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500 VESA 640/85 Hz 640 x 480 43.269 23.111 1.556 2.222 17.778 1.556 85.008 11.764 0.671 0.578 11.093 0.023 36.000 800/85 Hz 800 x 600 53.674 18.631 1.138 2.702 14.222 0.569 85.061 11.756 0.056 0.503 11.179 0.019 56.250 1024/85 Hz 1024 x 768 68.677 14.561 1.016 2.201 10.836 0.508 84.997 11.765 0.044 0.524 11.183 0.015 94.500
Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark
Negative Negative Separate
Negative Positive Separate
Negative Negative Separate
Negative Negative Separate
Positive Positive Separate
Positive Positive Separate
Separate Sync
Horizontal
Video Video
CC
Vertical
Video Video DD E
E Q
Q
RR
S S
Sync Sync B B AA
Sync Sync
PP
O O
A : Line time total C : Back porch E : Front porch AN17K*/AN17L*
B : Horizontal sync width D : Active time
O : Frame time total Q : Back porch S : Front porch
P : Vertical sync width R : Active time
2-3
2 Product Specifications
CONFIDENTIAL
Memo
2-4
AN17K*/AN17L*
CONFIDENTIAL
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the AN17K*/AN17L* monitor. WARNING: This monitor contains electrostatically sensitive devices. Use with caution when handling these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly. 2. To remove the Rear Cover, you must use the special opening jig tool.
3-1-1 Before Disassembly
1. Disconnect power cord from the monitor. 2. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base close to you.
4. Push the Opening jig in to each groove along the top of the monitor until makes a "tak" sound. (2 grooves : Left and Right, Make sure each snap is disengaged.)
3-1-2 Cabinet Disassembly
1. Remove the Stand from the monitor. (Refer to Stand manual) 2. Remove 2 screws on the Rear cover.
Figure 3 5. Pull the Rear Cover up and away from the monitor.
Figure 1 3. Tilt the monitor by lifting at the rear.
Figure 4 Figure 2
AN17K*/AN17L*
3-1
3 Disassembly and Reassembly 6. Remove the Shield.(TCO 99)
CONFIDENTIAL
3-1-4 Removing the Main PCB
1. Complete all previous steps. 2. Disconnect the Degaussing Coil at CN603 on the Main PCB. 3. Disconnect all easily accessible ground wires on the PCB and Bottom Chassis. 4. Disconnect the DY connector at the CN404 connector on the Main PCB. 5. Using the jig, release the snaps (2) connecting the Front Cover and the PCB then lift up the bottom to separate the two shields.
Figure 5 7. Using pinch-nose pliers or ling-nose pliers, carefully disconnect the Anode Cap from the CRT. Warning: Do not touch the Anode contact on the CRT (High Voltage may remain).
3-1-3 Removing the CRT Socket PCB
1. Complete all previous steps. 2. Loosen the screw on the CRT Neck and remove the CRT Socket PCB from the CRT.
Figure 7 6. Disconnect the tilt connector at the CN304 connector on the Main PCB. 7. Disconnect the Sub PCB connector at the CN604 connector on the Main PCB. 8. Remove the screws on the back and along each side of the bottom chassis. 9. Carefully lift the Main PCB Assy and remove the remaining ground wires. 10. Place the Main PCB Assy on a flat, level surface that is protected from static electricity.
Figure 6 3. Disconnect all connectors on the CRT Socket PCB. 4. Using a soldering iron, disconnect the Ground (GND) on the back of the Video Shield and remove the Shield Cap. 5. Remove the screw on the front of the Shield Socket. 6. Desolder the 4 tabs on the CRT Socket PCB and remove Shield. 7. Place the Video PCB on a flat, level surface that is protected from static electricity.
3-1-5 CRT Assy Disassembly
1. Complete all previous steps. 2. Straighten the Degaussing Coil Assembly coated metal ties and lift the Coil Assy from the CRT. 3. Remove the four corner screws and lift the CRT up and away from the Front Cover Assembly and place it on a padded surface. Caution: Do not lift the CRT by the neck. If you will be returning this CRT to the monitor, be sure to place the CRT face downward on a protective pad.
3-2 Reassembly
Reassembly procedures are in the reverse order of disassembly procedures. 3-2 AN17K*/AN17L*
CONFIDENTIAL
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).
4-1 Adjustment Conditions
Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the settings are not permanently stored and may be inadvertently deleted by the user.
4-1-1 Before Making Adjustments
4-1-1 (a) ORIENTATION When servicing, always face the monitor to the east. 4-1-1 (b) WARM-UP TIME The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments. 4-1-1 (c) SIGNAL Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: Separate (TTL level negative/positive) 4-1-1 (d) SCANNING FREQUENCY Horizontal : 30 kHz to 70 kHz (Automatic) Vertical : 50 Hz to 160 Hz (Automatic) Unless otherwise specified, adjust at the 1024 x 768 mode (68 kHz/85 Hz), Refer to Table 2-1 on page 2-3.
4-1-2 Required Equipment
The following equipment may be necessary for adjustment procedures: 4-1-2 (a) DISPLAY CONTROL ADJUSTMENT 1. Non-metallic () screwdriver: 1.5, 2.5, 3 mm 2. Non-metallic (+) screwdriver: 1.5, 2.5, 3 mm 3. Digital Multimeter (DMM), or Digital Voltmeter 4. Signal generator, or DM200 software 5. Personal computer 4-1-2 (b) COLOR ADJUSTMENTS 1. All equipment listed in 4-1-2 (a), above 2. Color analyzer, or any luminance measurement equipment.
AN17K*/AN17L*
4-1
4 Alignment and Adjustments
CONFIDENTIAL
Run the All Mode save in the Right Menu. Caution : Do not Run the All mode Save at the other scannig times except for 1024x768 (68kHz/85Hz). 4-2-3 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum
4-2 Display Control Adjustments
4-2-1 HIGH VOLTAGE
Signal: 1024 x 768 (68 kHz/85 Hz) Display image: Don't care Contrast: Minimum Brightness: Minimum Limit: 26.0 kV ± 0.3 kV Measure the high voltage level at the anode cap. High voltage should be within the limit as above.
4-2-2 CENTER RASTER
Adjust SW401 so that the back raster comes to the center when you apply basic mode for 17".
4-2-3 Centering
Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display. Adjust the horizontal size and vertical size to their optimal settings: 312 mm (H) x 234 mm (V). Adjust the horizontal position and vertical position to 5.0 mm of the center point of the screen. |A-B| 5.0 mm.
C
Use control bar after selecting "V-SIZE" in left menu to adjust the vertical size of the display pattern to 234 mm.(Tolerance: ± 4 mm.) 4-2-3 (c) HORIZONTAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image:
68 kHz/85 Hz Crosshatch pattern
Use control bar after selecting "H-POSITION" in left menu to center the horizontal image on the raster. 4-2-3 (d) VERTICAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern
|C-D| 5.0 mm.
DISPLAY AREA
A
B EDGE OF BEZEL D
Use control bar after selecting "V-POSITION" in left menu to center the vertical image on the raster.
Figure 4-3. Centering * In Softjig window, "Geometry" has to be selected for GD adjustment. 4-2-3 (a) HORIZONTAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum
4-2-4 Linearity
Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Tables 4-2 and 4-3, an image appears distorted, elongated or squashed. Table 4-1. Standard Modes Linearity: 1024x768/85Hz
Standard Modes Linearity
Click Standard Dump on the right Menu in the general field. Use control bar after selecting size B+ in the left Menu to adjust the horizontal size of the display, Pattern to 312mm(Tolerance : ±4mm.)
4:3
Difference between adjacent blocks (4 %) Horizontal: 20.9~23.1 Horizontal: Less than 0.88 mm Vertical : 20.9~23.1 Vertical : Less than 0.88 mm Each block (8 %)
4-2
AN17K*/AN17L*
4 Alignment and Adjustments Table 4-2. Other Modes Linearity: above 40 KHz(Hf)
Supported Timing Mode Each block (14 %) 4:3 Horizontal: 20.5~23.5 Vertical : 20.5~23.5 Difference between adjacent blocks (5 %) Horizontal: Less than 1.10 mm Vertical : Less than 1.10 mm
CONFIDENTIAL
Use control bar after selecting "PINBALANCE" in left menu to optimize the image.
4-2-7 Parallelogram Adjustment
CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum
Off Spec : Under 40 KHz (Hf) 4-2-4 (a) VERTICAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Vertical Linearity, refer to Tables 4-2 and 4-3 for the tolerance range. Use control bar after selecting "V-LINEARITY BAL" in left menu to optimize the image.
Use control bar after selecting "PARALLEL" in left menu to make the image area rectangular.
4 mm
Figure 4-6. Parallelogram
4-2-8 Side Pincushion Adjustment
CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz Crosshatch pattern
4-2-5 Trapezoid Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum
Use control bar after selecting "PINCUSHION" in left menu to straighten the sides of the image area.
| C1 |, | C2 | 2.0 mm, | D1 |, | D2 | 2.0 mm. C2
Use control bar after selecting "TRAPEZOID" in left menu to make the image area rectangular.
| A - B | < 4 mm A A D1
D2
B
B
C1
Figure 4-4. Trapezoid
Figure 4-7. Pincushion
4-2-9 Degauss
No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once every 30 minutes.
4-2-6 Pinbalance Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Crosshatch pattern Maximum Maximum
4-2-10 To Delete the User Mode Data
To delete the adjustment data from the user modes, click "@4: USER DELETE" in right menu.
D1
D1
D2
4-2-11 Save the Data
To save the adjustment data for a mode, press "@3: ALL MODE SAVE" in right menu.
Figure 4-5. Pinbalance AN17K*/AN17L* 4-3
4 Alignment and Adjustments
CONFIDENTIAL
4-3-2 (b) WHITE BALANCE ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: White box pattern Brightness: 0.06ft-L at Back Raster Pattern Display Contrast: Maximum
4-3 Color Adjustments
CAUTION:Check below condition before color adjustment Video signal : Analog 0.7 Vp-p (at 75 ) Sync : TTL level (H, V seperate signal) * Select "Color" in Softjig menu for color adjustment.
4-3-1 Color Coordinates (Temperature)
Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum. CONDITIONS Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz Display image: White flat field at center of display area Luminance: Maximum PROCEDURE Use the directions in sections 4-3-2 through 4-3-3 to adjust the color coordinates for: 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02 6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02
1/3H-1/2H FRONT BEZEL OPENING 1/3V-1/2V BACK RASTER WHITE WINDOW
Figure 4-8. White Box Pattern 1. Use control bar after selecting "RED GAIN", "GREEN GAIN" and "BLUE GAIN" to adjust the luminance to AN17K*, (40 ± 1 ft-L), AN17L*(42 ± 1 ft-L) with the color coordinates ranged for 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02. 4-3-2 (c) ABL ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz Full white pattern Maximum Maximum
FRONT BEZEL OPENING BACK RASTER
4-3-2 Color Adjustments for 9300K
4-3-2 (a) BACK RASTER COLOR ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast:
68 kHz/85 Hz Back raster pattern Maximum Maximum
WHITE WINDOW
Figure 4-9. Full White Pattern 1. Check the ABL. If it is not within specifications, use the ABL controls to adjust. (30 ± 1 ft-L ) AN17K* (31 ± 1 ft-L ) AN17L* 2. Select "@4: COLOR SAVE" to save the data. 3. Select "@6: ALL COLOR SAVE" to save CH2.
1. Select "@1: CHANNEL 1" in right menu to control the color for 9300K. 2. Adjust the luminance of the back raster to between 0.5 to 0.7 ft-L using control bar after selecting "GREEN CUTOFF" in the menu. 3. Use control bar after selecting "BLUE CUTOFF" in left menu to set the "y" coordinate to 0.298 ± 0.02. 4. Use control bar after selecting "RED CUTOFF" in left menu to 0.283 ± 0.02. * If color values can not be matched to desirable values, repeat sequences 3 and 4 after readjusting "GREEN CUTOFF" control.
4-4
AN17K*/AN17L*
4 Alignment and Adjustments 4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION CONDITIONS Scanning frequency: Display image: X-Y Coordinates: ABL Luminance Brightness: Contrast:
CONFIDENTIAL
PROCEDURE Measure luminance at nine points on the display screen (see figure below). 68 kHz/85 Hz Back raster pattern Full White Pattern x = 0.283 ± 0.02, y = 0.298 ± 0.02 Refer to 4-3-2(c) Maximum 5 ft-L, 24 ft-L Figure 4-10. Luminance Uniformity Check Locations
1. Check whether the color coordinates of the back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. 2. Display a full white pattern. 3. Select "Geometry" in softjig menu. 4. Select "@7: 5-ft " in right menu. 5. Check whether the white coordinates of the video meet the above coordinates spec. 6. Select "@8: 24-ft " in right menu. 7. Check whether the white coordinates of the video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. Select "Color" and click "@2: CHANNEL 2" for color ajdustment for 6500K Repeat the sequence for 9300K adjustment. luminance values are the same as 9300K, but the color coordinats of back raster and white box are : x = 0.313 ± 0.02 y = 0.329 ± 0.02
4-3-4 Focus Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (1024 x 768) "H" character pattern Cut off point Maximum
PROCEDURE 1. Adjust the Focus VR on the FBT to display the sharpest image possible. 2. Use Locktite to seal the Focus VR in position.
4-3-5 Color Purity Adjustment
Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface. CONDITIONS Orientation: Scanning frequency: Display image: Luminance:
4-3-3 Luminance Uniformity Check
Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10. CONDITIONS Scanning frequency: Display image: Brightness: Contrast:
Monitor facing east 68 kHz/85 Hz White flat field Cut off point at the center of the display area
Note: Color purity adjustments should only be attempted by qualified personnel. 68 kHz/85 Hz (1024 x 768) White flat field Cut off point at 24 ft-L Maximum
AN17K*/AN17L*
4-5
4 Alignment and Adjustments PROCEDURE For trained and experienced service technicians only. Use the following procedure to correct minor color purity problems: 1. Make sure the display is not affected by external magnetic fields. 2. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm. 3. Display a green pattern over the entire display area. 4. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. AN17K*(Optimum setting: x = 0.276 ± 0.015, y = 0.596 ± 0.015) AN17L*(Optimum setting: x = 0.285 ± 0.015, y = 0.600 ± 0.015) 5. Repeat steps 4 and 5 using a red pattern and then again, using a blue pattern. Table 4-4. Color Purity Tolerances
Red: Green: Blue: x = 0.645 ± 0.015 x = 0.276 ± 0.015 x = 0.145 ± 0.015 y = 0.318 ± 0.015 y = 0.596 ± 0.015 y = 0.060 ± 0.015
CONFIDENTIAL
(AN17KS Model)
(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02) Red: Green: Blue: x = 0.645 ± 0.015 x = 0.285 ± 0.015 x = 0.142 ± 0.015 y = 0.321 ± 0.015 y = 0.600 ± 0.015 y = 0.057 ± 0.015
(AN17LS Model)
(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)
6. When you have the PCMs properly adjusted, carefully glue them together to prevent movement during shipping.
4-6
AN17K*/AN17L*
CONFIDENTIAL
5 Troubleshooting
5-1 Parts Level Troubleshooting
Notes: Check the following circuits. · No raster appears: Power circuit, Horizontal output circuit. · High voltage develops but no raster appears: Video output circuits. · High voltage does not develop: Horizontal output circuits.
5-1-1 No Power Supply
Check and replace D601 and FH1
WAVEFORMS
1 100 V (IC601, #1)
Chirping noise exists?
Yes
Check and replace IC601.
No Repeating start? Yes Check and replace D606.
CH1 P-P = 100 V CH1 RMS = 350.2 V
No
1
IC601 Pin 1 waveform is right?
No
Check and replace Q602, IC601, IC605 and IC602.
Yes C622 Voltage is 13 V ± 0.5V? No Check and replace IC201, IC301, IC605, IC401, Q402, Q404, and 12V Regulafor circuit.
Yes Normal operation? Yes Verify voltages. No Replace Main board.
Done.
AN17K*/AN17L*
5-1
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
2 100V (IC601, #1)
5-1-2 DPMS Failure
Check signal source H/V Sync. video level.
Make No H/V Sync. (power off mode)
LED blinks?
No
Check IC201 Pin 40.
CH1 P-P = 100V CH1 RMS = 325.8 V
Yes +12 V line off? No Check IC201 Pin 5/Pin 6 and Q610/Q602 operation.
Yes Q602 Base voltage exists? Yes
2
No
Check IC201 Pin 5. Check and replace Q602 and IC201.
IC601 Pin 1 output voltage exists? Yes Done
No
Refer to 5-1-1 No Power Supply.
5-2
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
No Does DC 12V appear at Pin 29 of IC401? Yes No Check 12 V line.
5-1-3 H_Deflection Failure
Does PWM output signal appear at Pin 28 (B_DRV) of IC401? Yes
3
WAVEFORMS
Check IC401. 3 2.00 V (IC401, #28) Does Horizontal pluse signal appear at Pin 26 of IC401? Yes
5
4
No
Check IC401.
Does 110 Vp-p signal appear at Collector of Q403? Yes Check Q402, Q404 and T401.
No
Check Q403.
CH1 P-P = 2.00V CH1 RMS = 5.868V
4 2.00V (IC401, #26)
CH1 P-P = 2.00V CH1 RMS = 5.868V
5 20.0 V (Q403, Collector)
5-1-4 S Correction Failure
Check S1 ~ S3 signal.
S1~S3 signals are correct at each frequency block? Yes Check and replace Q409, Q410, Q411, Q414, Q415, Q416, D402, D403, QD404.
No
Check and replace IC201.
CH1 P-P = 20.0 V CH1 RMS = 46.80V
AN17K*/AN17L*
5-3
5 Troubleshooting
CONFIDENTIAL
Check and Replace T402
5-1-5 H_Lin. Failure 5-1-6 Invariable H_Size
IC401 Pin 28 voltage varies with different B_DRV DAC values? Yes Q402 Gate output duty varies with different B_DRV DAC values?
No
Check and replace IC401.
No
Check some parts around Q402, IC401 Pin 14 ~ 16.
5-1-7 Abnormal H_Size
IC401 Pin 24 output duty varies with different B+ offset DAC values? Yes
6
No
WAVEFORMS
Check and replace IC201. 6 200 V (Q404, Collector)
Q404 Collector waveform is right? Yes Check Components around D409 and L401.
No
Check and replace Q405, Q406, Q407, and Q408.
CH1 P-P = 200V CH1 RMS = 387.2V
5-4
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
No
5-1-8 Side Pin or Trap Failure WAVEFORMS
Check and replace IC401. 7 1.00 V (IC401, #24) Yes Refer to 5-1-7 Abnormal H_Size.
7
IC401 Pin 24 output exists?
CH1 P-P = 1.00V CH1 RMS = 3.008 V
5-1-9 Para. or Pin Balance Failure
IC401 Pin 24 output varies with different DAC values? No Replace IC401. Yes
Refer to 5-1-7 Abnormal H_Size.
5-1-10 Tilt Failure
Check tilt connector connection
IC201 Pin 20 output duty varies with different DAC values? Yes Q611 Base output varies with different DAC values? Yes Check and replace Q301 and Q302.
No
Check and replace IC201.
No
Check and replace Q611.
AN17K*/AN17L*
5-5
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
No Refer to 5-1-1 No Power Supply 8 500 V (IC401, #23)
5-1-11 V Deflection Failure
13V and 13V lines are on?
Yes
8
IC401 Pin 23 output exists?
No
Check and replace IC401.
Yes
9
CH1 P-P = 500 V CH1 RMS = 1.425 V
IC301 Pin 6 output exists?
No
Check and replace components around IC301.
9 10.0 V (IC301, #6)
Yes Check DY connector connection.
CH1 P-P = 10.0 V CH1 RMS = 5.06 V
5-1-12 V Size or Position Variation Failure
IC401 Pin 23 output varies with different DAC values? Yes Check and replace IC301. No
Check and replace IC201 and IC401.
5-6
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
No Check and replace IC401 and +12 V line. 3 2.00 V (IC401, #28)
5-1-13 High Voltage Failure
3
IC401 Pin 28 OSC pulse exists?
Yes
10
Q402 Gate driving pulse exists?
No
Check and replace Q401 and Q420.
Yes
11
CH1 P-P = 2.00 V CH1 RMS = 5.868 V
Q402 Drain pulse exists?
No
Check and replace Q402, L402 and D401. Check 50V Line.
10 2.00 V (Q402, Gate)
Yes Done
CH1 P-P = 2.00 V CH1 RMS = 7.692V
5-1-14 ABL Failure
11 50.0 V (Q402, Drain)
Input full white pattern to monitor.
IC101 Pin 8 input exists and varies with different patterns? Yes Check CN102.
No
Check and replace IC101.
CH1 P-P = 50.0 V CH1 RMS = 73.7V
T501 Pin 8 output exists?
No
Check and replace T501.
Yes IC201 Pin 26 output exists and varies with different patterns? Yes Done No Check and replace IC201.
AN17K*/AN17L*
5-7
5 Troubleshooting
CONFIDENTIAL
No
5-1-15 Dynamic Focus Failure WAVEFORMS
Replace the IC401. 12 2.00 V (IC401, #32) IC401 Pin 32 output is right?
12
Yes Some parts around Q551 are right? No Replace failed part.
Yes
13
CH1 P-P = 2.00V CH1 RMS = 6.124V
T502 Pin 6 input is right?
No
Check and replace C432.
13 50.0 V (T502, #6)
Yes
14
T502 Pin 1 output is right?
No
Replace the T502.
CH1 P-P = 50.0V CH1 RMS = 75.6V
Yes Check the connection between FBT Focus pin and CRT Socket PCB.
14 100 V (T502, #1)
CH1 P-P = 100V CH1 RMS = 124.0V
5-8
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
15 1.00V (IC101 #12,14,16)
5-1-16 No Video
Check signal cable and connection.
15
IC101 Pin 12, 14 and 16 inputs are right? Yes
No
Check the signal cable connection.
16
IC101 Pin 18, 21 and 24 outputs are right? Yes
No
Check I2C bus and +12V line.
CH1 P-P = 1.00V CH1 RMS = 2.452V
16 1.00V (IC101 #18,21,24) No Check +12V, +80V line. Check and replace IC102.
17
IC102 Pin 9, 10 and 11 outputs are right? Yes Cathode DC levels are right?
No
Check +80V line. Check and replace IC104.
CH1 P-P = 1.00V CH1 RMS = 2.792V
17 20.0V (IC102, #9, 10, 11) Yes G2 voltage is right? No Check G2 wire, CRT Socket board and FBT.
Yes Change CRT.
CH1 P-P = 20.0V CH1 RMS = 40.52V
Done.
AN17K*/AN17L*
5-9
5 Troubleshooting
CONFIDENTIAL
No
5-1-17 Micom Failure WAVEFORMS
Check IC604. 18 1.00 V (IC201, #13, 14) Yes
18
IC201 Pin 11 input voltage is 5V?
IC201 Pin 13 and 14 inputs are right? Yes
No
Check C202, C203 and X201.
CH1 P-P = 1.00 V CH1 RMS = 2.108V
IC201 Pin 18 input is right?
No
Check and replace IC201 and R206.
Yes All in/output values are right? No Replace IC201.
Yes Done
5-10
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
19 1.00 V (IC101, #32) No Check and replace R117, C117 and IC101.
5-1-18 OSD Failure
Check CN102 and connector Ass'y. Yes
19
IC101 Pin 32 input is right?
Yes
20
IC101 Pin 1 input is right?
No
Check CN102 Pin 8.
CH1 P-P = 1.00V CH1 RMS = 4.516V
20 1.00 V (IC101, #1) Yes IC101 Pin 29 and 30 inputs are right? Yes IC101 Pin 18, 21 and 24 outputs are right? Yes Check and replace IC102. No
CH1 P-P = 1.00V CH1 RMS = 5.024V
No
Check IC201 Pin 41 and 42.
21
Check and replace IC101. 21 1.00 V (IC101, #18,21,24)
Done
CH1 P-P = 1.00V CH1 RMS = 2.580V
AN17K*/AN17L*
5-11
5 Troubleshooting
CONFIDENTIAL
No Check the button. (SW201 ~ SW204)
5-1-19 User Control Failure
Does the DC level change at Pin 38 of IC201 when you push the S/W button? Yes Check IC201.
5-1-20 Degaussing Failure
Check degaussing connector.
RL601 operation is right?
Yes
Check D-coil and TH601.
No Q601 base input is right? Yes Check and replace Q601.
No IC201 Pin 4 output is right? No Check and replace IC201.
Yes Done
5-12
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
5-2 General Troubleshooting
5-2-1 No Picture
Yes
LED blinks?
Refer to 5-2-2 Shut down.
No LED is green color? Yes Check Micom.
No Check G2 voltage, high voltage and R, G, B cathode voltage.
5-2-2 Shut Down
Blinking LED's?
No
Check power supply.
Yes Scan failure? Yes Check horizontal, vertical deflection system and check power supply secondary voltages.
No Video failure? Yes Check Video board.
No Check and replace IC201.
Done
AN17K*/AN17L*
5-13
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
No Check signal generator.
5-2-3 Missing Color
Proper Video levels are on CN101 (D-Sub) Pin 1, 3 and 5? Yes
22
22 10.0 V (R,G,B, Video)
Proper Video signal to all cathodes? Yes
No
Refer to 5-1-16 No Video.
CH1 P-P = 10.0V CH1 RMS = 17.02V
Proper DC voltage to all cathodes?
No
Check IC101 Pin 17, 20 and 23. Check IC104.
Yes G2 voltage is right? Yes Heater voltage is right? No Check D608, Q604 and T601. No Check T501 and D502, D512.
Yes G1 voltage is right? Yes Replace CRT. No Check D504, Q502 and T501.
Done
5-14
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
23 5.00V (Q303, Collector)
5-2-4 Visible Retrace
Check white balance adjustment.
G2 voltage is right?
No
Check D502, D512.
Yes Blank pulse at Pin 3 of IC401? No Check IC401.
CH1 P-P = 5.00V CH1 RMS = 28.33V
Yes
23
24 20.00V (CRT Socket, G1) No
V_FLB pulse at Collector of Q303? Yes
Check Q303.
24
Valid the Vertical pulse on CRT Socket G1? Yes Done
No
Check CN102 and CN201.
CH1 P-P = 20.0V CH1 RMS = 66.68V
AN17K*/AN17L*
5-15
5 Troubleshooting
CONFIDENTIAL
5-2-5 Unsynchronized Image
Check input signals Pin 2 and 3 of CN202.
Signals are right?
No
Check Video Cable
Yes Signals at Pin 28 and 29 of IC201 are right? Yes Signals at Pin 1 and 2 of IC401 are right? Yes Check circuits on Main board. No Check IC401 No Check IC201.
Done
5-16
AN17K*/AN17L*
5 Troubleshooting
CONFIDENTIAL
5-2-6 Misconvergence
Adjust convergence.
Convergence is now within spec.? No Readjust convergence.
Yes
Done
Convergence is now within spec.? No Change CRT and readjust convergence.
Yes
Done
Done
AN17K*/AN17L*
5-17
5 Troubleshooting
CONFIDENTIAL
5-2-7 Poor Focus
Adjust focus VR of FBT.
Improved focus?
Yes
Align monitor and check for focus change.
No Check focus leads from FBT to CRT Socket.
Check CRT Socket.
Dynamic focus circuit is right?
No
Refer to 5-1-15 Dynamic Focus Failure.
Yes Replace the CRT and verify focus.
5-2-8 Purity Failure
Degause
Purity is correct?
Yes
Done
No Degaussing circuit is correct? No Refer to 5-1-20 Degaussing Failure.
Yes Replace CRT and verify purity.
5-18
AN17K*/AN17L*
CONFIDENTIAL
6 Exploded View and Parts List 6-1-1 AN17KS
AN17K*/AN17L*
6-1
6 Exploded View & Parts List
CONFIDENTIAL
6-1-2 AN17KS Front
7
8
6 4 5 9
3 2
1
6-2
AN17K*/AN17L*
6 Exploded View & Parts List
CONFIDENTIAL
6-2-1 AN17KT
AN17K*/AN17L*
6-3
6 Exploded View & Parts List
CONFIDENTIAL
6-2-2 AN17KT Front
5
9 8 10
6 4 1 3 2
6-4
AN17K*/AN17L*
6 Exploded View & Parts List
CONFIDENTIAL
6-3-1 AN17LS
AN17K*/AN17L*
6-5
6 Exploded View & Parts List
CONFIDENTIAL
6-3-2 AN17LS Front
5
9 10 7 8
4 1 3 2
6-6
AN17K*/AN17L*
6 Exploded View & Parts List
CONFIDENTIAL
6-4-1 AN17LT
AN17K*/AN17L*
6-7
6 Exploded View & Parts List
CONFIDENTIAL
6-4-2 AN17LT Front
5
9 10 8
6 4 1 3 2
6-8
AN17K*/AN17L*
CONFIDENTIAL
7 Electrical Parts List
7-1-1 AN17K* Main PCB Parts
Loc. No. AN_LABEL C409 C430 C601 C602 C608 CIS1 CIS11 CIS12 CIS13 CIS14 CIS15 CIS16 CIS2 CIS3 CIS4 CIS8 CLAMP1 CLAMP2 CN201 CN202 CN404 CN501_G2 CN601 CN604 D406 D409 D601 D608 D609 D611 FUSE IC201_SOCK IC401 IC605 L401 L402 L403 L601 OP201 Q409 Q410 RL601 S_CABLE SW401 SW601 T401 T402 T501 T502 T601 T602 Code No. BH94-00823A BH68-00446D 2306-000248 2301-001125 2301-001195 2301-001195 2401-002128 0202-001044 BH68-00001A BH71-00110A BH72-00025A BH72-00026A BH72-00261A BH73-60304C 0202-001046 0202-001222 0204-001095 3301-000233 6502-000001 6502-000001 3711-003895 3711-003873 3711-003989 BH39-00242A 3721-001053 BH39-00288A 0402-001025 0402-001295 0402-000103 0402-001456 0402-000005 0402-001456 3601-001302 3704-001071 1204-002013 0604-001018 BH27-00131A BH27-00135A BH27-20342U BH29-00001A 0601-001147 0505-001675 0505-001675 3501-001111 BH39-00405A 3406-000002 3403-001132 BH26-00027A BH27-00139A BH26-00143A BH26-00114A BH26-00142A BH26-00141A Description ASSY PCB MAIN LABEL C-FILM,MPPF C-FILM,MPPF C-FILM,MPPF C-FILM,MPPF C-AL SOLDER-WIRE. LABEL-MARK CDT SHIELD BOTTOM GUIDE-POWER SHAFT-POWER SHEET ABS-LMF RUBBER-SUPPORT SOLDER-WIRE FLUX SOLDER-WIRE FLUX THINNER CORE-FERRITE CABLE CLAMP CABLE CLAMP CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CBF HARNESS PLUG-AC POWER CBF HARNESS DIODE-RECTIFIER DIODE-RECTIFIER DIODE-BRIDGE DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER FUSE-AXIAL LEAD SOCKET-IC IC-DEF. PROCESSOR PHOTO-COUPLER COIL CHOKE COIL CHOKE COIL-CHOKE FILTER LINE NOISE LED FET-SILICON FET-SILICON RELAY-POWER CBF SIGNAL SWITCH-ROTARY SWITCH-PUSH TRANS-HOR.DRIVE COIL LINEARITY TRANS FBT TRANS-FOUCS TRANS SWITCHING TRANS-SYNC Specification AN17KS AN-STICKER,ART-PAPER 100G,15,15,BLACK,YELLOW 680nF,5%,250V,BK,26.5x16.5mm,2 600nF,5%,250V,TP,26x20x11.5,20 150nF,10%,275VAC,BK,26x16.5x7, 150nF,10%,275VAC,BK,26x16.5x7, 220uF,20%,400V,GP,BK,25x40mm,10 S63S-W3.0,S63S,D3,63Sn/37Pb,ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT PN15VT,SECC ,T1.0 CDA4507,ABS,V0,IV16 CDA4507,ABS,V0,IV16 IB10LO,AL+PET,-,-,-,-,-,DP15LT,CR V0,GRAY,-,14*7*10,-,CF-110VH-2A,-,-,-,RS-107,RS60-1.2AA,D1.2,SN60/PB40,#4520,-,-,ZZ,18x9.5x28mm,-,DAWH-5NB,D15,L35,NYLON66,NTR DAWH-5NB,D15,L35,NYLON66,NTR BOX,13P,1R,2mm,STRAIGHT,SN BOX,7P,1R,2mm,STRAIGHT,SN NOWALL,4P,1R,8mm,STRAIGHT,SN DB5907,UL1032,UL/CSA,1P,290MM,RED,AWG22,YFH800,YPT-018,-,-,-,-,-,-,CBF-GND ASS'Y 3P,-,-,NI PN17LO,UL1007,UL/CSA,2P/2P,130MM,BLU/WHT,AWG26,YBNH200,SMP250,-,-,-,-,-,-,CBF-CO ERD07-15,1.5KV,1.5A,-,TP GUR460L-5700,600V,4A,DO-201AD,BK D2SBA60,600V,1.5A,SIP-4,ST UG2D,200V,2A,DO-204AC,BK 31DF4,400V,3A,DO-201AD,BK UG2D,200V,2A,DO-204AC,BK 250V,3.15A,SLOW-BLOW,CERAMIC,5X20MM 42P,DIP,SN,1.778mm STV6888,DIP,32P,400MIL,PLASTIC,13.2V,-,0TO+70C,ST,100KHZ DAR-TR,63-125%,200mW,DIP-4,ST 150UH,AN17K,150UH,10%,0.35OHM,2.5A,AR8X25,72.5TS,18X39MM,11MM,BK 120UH,CDTMO,120UH,10%,0.23OHM,5A,AR8X25,65.5TS,18X40MM,11MM,USTC0.12X20,TR,-10CT -,8.2MH(250KHz),10%,DR8*11,-,-,-,-,10.5OHM,-,-,-,BULK CDTMO,30MH,0.39OHM,30MH,26X21X36MM,300KHZ 35KOHM,220V,BK,30MH MIN,100MOHM,-10CTO ROUND,GRN,4.75mm,565nm IRF630B,N,200V,9A,0.4OHM,72W,TO-220 IRF630B,N,200V,9A,0.4OHM,72W,TO-220 12Vdc,250mW,5A,1FormA,15mS,5mS AN15/17**,15P/06P,07P,20276-N,1500MM,UL20276,IVORY,D-SUB/MALE,ATT. TYPE 36Vdc,200mA,SP3T,30VDC,0.3A,DPST,SELF LOCK,-,-,-,-,-,-,-,-,-,-,-,PL-3,EI 1916,310uH,-,-,6.4UH,6.4UH,DR1215 C:4.5,7.0MM,13.8X14.5X46MM,12X8T,25TS,BK,12%,0.04OHM,USTC0.12 FQM17B015,AN17L,1.21MH,SM19C,FUR3757SU,0.510OHM,153.7V,13P,-10 ~60,BK,27.0KV EE-1916,PN17L,5P,1.7mH,-,-,70mH,-,-,0.85ohm/8.5ohm,-,PL3,DMR30,EE-1916,20uH MAX, EER3435,AN17L,90 ~264,EER3435,350UH,89.0UH AR0615(L-81),AN17L,5P,200UH,200UH,1.30 OHM,L-81,AR0630, BAR,18*13*18.5,BK Remarks SNA
SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
SNA
SNA
SNA
!
!
AN17K*/AN17L*
7-1
7 Electrical Parts List
CONFIDENTIAL
Description THERMISTOR-PTC THERMISTOR-NTC ASSY MICOM IC-MICROCONTROLLER S/W MICOM ASSY AUTO-MAIN CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-AL C-FILM,MPEF C-FILM,MPEF C-AL C-FILM,PEF C-AL C-AL C-FILM,MPEF C-FILM,PEF C-CERAMIC,MLC-AXIAL C-AL C-CERAMIC,MLC-AXIAL C-AL C-FILM,MPEF C-CERAMIC,MLC-RADIAL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-AL C-FILM,PEF C-FILM,PEF Specification 4.5OHM,+30/-20%,220V,290VAC,21A,-,TR 8ohm,15%,-,17mW/C,BK AN17KS 3P863,8Bit,SDIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,1040BYTE,48KBYTE AN17KS AN17KS AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),220uF,20%,16V,GP,-,6.3x11mm,2. 0.022nF,5%,50V,NP0,TP,5x3,5 0.022nF,5%,50V,NP0,TP,5x3,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 1uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 1nF,10%,50V,Y5P,TP,5x3.5,5 100nF,5%,100V,TP,11.5x12.5mm,5 100uF,20%,16V,GP,TP,6.3x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 4.7uF,20%,50V,GP,TP,5x11,5 150nF,5%,100V,TP,10.5x5x14.5,5 470nF,5%,63V,TP,-,5mm 47uF,20%,16V,GP,TP,5x11,5 3.3nF,5%,100V,TP,5.8x3x12.5,5m 470uF,20%,16V,GP,TP,8x11.5,5 220uF,20%,35V,WT,TP,10x20,5 1uF,5%,63V,TP,7.5x15.5mm,5mm 10nF,5%,100V,TP,7x3.2x7mm,5mm 100nF,+80-20%,50V,Y5V,TP,2.3X3 10uF,20%,16V,GP,TP,5x11,2.5 10nF,+80-20%,50V,Y5V,TP,2.3X3. 47uF,20%,16V,GP,TP,5x11,5 100nF,5%,63V,TP,7.5x4.0x5.0mm, 820pF,5%,50V,NPO,TP,5.1x3.2x5. 10nF,5%,100V,TP,7x3.2x7mm,5mm 0.33nF,10%,50V,Y5P,TP,4x3.5,5 2.7nF,5%,100V,TP,7x3.0x6.5mm,5 220UF,20%,63V,LR,TP,10X25MM,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 100uF,20%,16V,GP,TP,6.3x11,5 33nF,5%,100V,TP,5.8x12.5x3,5 22nF,5%,100V,TP,7.2x4.5x9.0mm, Remarks
Loc. No. TH601 TH602 CIS7 IC201 CIS BD301 BD302 BD401 BD402 BD403 BD404 BD410 BD601 BD602 BD603 BD605 C201 C202 C203 C204 C205 C207 C209 C210 C211 C212 C213 C214 C215 C216 C301 C302 C303 C304 C305 C306 C307 C308 C309 C312 C340 C401 C402 C403 C404 C405 C406 C407 C408 C410 C411 C412
Code No. 1404-001264 1404-001020 BH97-00330E 0903-001194 BH46-00005T BH97-00346A 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 2401-000010 2201-000389 2201-000389 2301-000148 2401-000603 2401-000603 2401-002075 2401-000603 2201-000146 2201-000017 2301-000010 2401-000025 2201-000146 2401-002075 2301-001049 2305-000412 2401-000031 2301-000519 2401-000037 2401-000856 2305-000237 2301-000148 2202-002009 2401-000050 2202-002008 2401-000031 2305-000665 2202-000573 2301-000148 2201-000471 2301-000203 2401-003826 2201-000291 2401-000025 2301-000005 2301-000016
SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
7-2
AN17K*/AN17L*
7 Electrical Parts List
CONFIDENTIAL
Description C-AL C-AL C-AL C-FILM,PEF C-FILM,MPE-PPF C-FILM,PPF C-FILM,PPF C-AL C-FILM,MPPF C-AL C-FILM,MPPF C-AL C-FILM,MPPF C-FILM,MPEF C-FILM,MPEF C-CERAMIC,DISC C-AL C-AL C-FILM,PEF C-AL C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-CERAMIC,MLC-AXIAL C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-AL Specification 3.3UF,20%,50V,BP,TP,16X25,7.5 470nF,20%,50V,GP,TP,5x11,2.5 4.7UF,20%,160V,WT,TP,8X11.5MM,5 100nF,5%,100V,TP,11.5x12.5mm,5 2.2nF,5%,1.6KV,TP,23x16x9,7.5m 2.5nF,5%,1.6kV,TP,21x6.8x12.6mm,7.5 5.2nF,5%,630V,TP,19x7x13,7.5 1uF,20%,50V,GP,TP,5x11,5 120nF,5%,250V,TP,19x15x7,7.5mm 1uF,20%,50V,GP,TP,5x11,5 150nF,5%,250V,TP,19x16x7.5,7.5 1uF,20%,50V,GP,TP,5x11,5 200nF,5%,250V,TP,17.5x7x13mm,7.5 15nF,10%,250V,TP,13X9.0X4.5mm, 10nF,5%,250V,TP,13x4.5x9mm,7.5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 1uF,20%,50V,BP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 1uF,20%,50V,GP,TP,4x7mm,1.5mm 22nF,5%,100V,TP,7.2x4.5x9.0mm, 10uF,20%,16V,GP,TP,5x11,2.5 100nF,+80-20%,50V,Y5V,TP,8x3,5 0.33nF,10%,50V,Y5P,TP,4x3.5,5 220nF,20%,50V,GP,-,5x11,5 2.2uF,20%,250V,GP,TP,8x11.5,5 2.2uF,20%,160V,GP,TP,6.3x11,5 56nF,5%,100V,TP,9.5x12.5mm,5mm 10NF,+80-20%,1KV,Y5V,TP,20*4,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 2.2nF,5%,100V,TP,5.5X10X2.9,5m 10uF,20%,16V,GP,TP,5x11,2.5 0.1nF,10%,500V,Y5P,TP,6.5x3,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 4.7nF,20%,250VAC,Y5U,TP,16x7,7 4.7nF,20%,250VAC,Y5U,TP,16x7,7 33nF,5%,100V,TP,5.8x12.5x3,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 33uF,20%,50V,WT,-,6.3x11mm,2.5 100uF,20%,16V,GP,TP,6.3x11,5 1uF,20%,50V,WT,TP,5x11,5 1uF,20%,50V,WT,TP,5x11,5 0.22nF,10%,1kV,Y5P,TP,6.3x5,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 2.2nF,20%,125V,Y5U,TP,11x7,5 2.2nF,20%,125V,Y5U,TP,11x7,5 1000uF,20%,16V,GP,TP,10x16,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 220UF,20%,63V,LR,TP,10X25MM,5 Remarks
Loc. No. C413 C414 C415 C416 C419 C420 C421 C423 C425 C426 C427 C429 C431 C432 C433 C436 C440 C461 C462 C463 C501 C502 C503 C504 C505 C508 C509 C510 C512 C513 C514 C515 C516 C517 C518 C541 C551 C552 C553 C603 C604 C606 C607 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620
Code No. 2401-001012 2401-001334 2401-001222 2301-000010 2309-000106 2303-000165 2303-001029 2401-000603 2306-000125 2401-000603 2306-000131 2401-000603 2301-001324 2305-001033 2305-001003 2201-000291 2401-001914 2401-002075 2301-000148 2401-000597 2301-000016 2401-000050 2201-000119 2201-000471 2401-000059 2401-002267 2401-000625 2301-000294 2201-000152 2201-000291 2201-000469 2201-000469 2201-000469 2201-000469 2201-000019 2301-000004 2401-000050 2201-000132 2201-000291 2201-000024 2201-000024 2301-000005 2202-002009 2401-000015 2401-000025 2401-000613 2401-000613 2201-000012 2201-000019 2201-000291 2201-000023 2201-000023 2401-000039 2201-000469 2401-003826
! !
AN17K*/AN17L*
7-3
7 Electrical Parts List
CONFIDENTIAL
Description C-AL C-AL C-AL C-FILM,PEF C-FILM,PEF C-AL C-AL C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-AL C-AL C-AL C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL TAPE-KRAFT TAPE-PAPER CONNECTOR-HEADER EYELET CONNECTOR-HEADER DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER Specification 47uF,20%,50V,GP,TP,8x11.5,5 1000uF,20%,16V,GP,TP,10x16,5 1000uF,20%,16V,GP,TP,10x16,5 2.2nF,5%,100V,TP,5.5X10X2.9,5m 15nF,5%,100V,TP,7.2x4.0x7.5mm, 100uF,20%,16V,GP,TP,6.3x11,5 100uF,20%,16V,WT,TP,8x11.5mm,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 470uF,20%,16V,GP,TP,8x11.5,5 100uF,20%,16V,WT,TP,8x11.5mm,5 1uF,20%,50V,GP,TP,5x11,5 10uF,20%,50V,GP,TP,5x11,5 47uF,20%,50V,GP,TP,8x11.5,5 4.7nF,5%,100V,TP,10.5x12.5x6.5 1nF,10%,50V,Y5P,TP,5x3.5,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 #53110,T0.1,W6,L2000M,BRN #53128,T0.15,W5.5,L2000M,BEIGE 1WALL,3P,1R,2.5mm,STRAIGHT,SN ID2.2,OD2.7,L3.1,SN,BSS3-E/EH 1WALL,3P,1R,3.96mm,STRAIGHT,SN 1N4148,100V,200mA,DO-35,TP UF4004,400V,1A,DO-41,TP 1N4148,100V,200mA,DO-35,TP TVR10G,400V,1.0A,DO-41,TP UF4004,400V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP EK-04,40V,1.5A,DO-41 UF4004,400V,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP UF4004,400V,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP UF4004,400V,1A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP RGP02-12,1200V,0.5A,DO-204AL,T TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP RGP02-12,1200V,0.5A,DO-204AL,T 1N4148,100V,200mA,DO-35,TP RGP02-16E,1.6KV,0.5A,DO-41,TP Remarks
Loc. No. C621 C622 C623 C624 C625 C626 C627 C628 C629 C630 C631 C633 C634 C635 C636 C643 C649 CIS5 CIS6 CN304 CN501 CN603 D201 D301 D302 D303 D401 D402 D403 D404 D405 D407 D410 D411 D412 D413 D414 D415 D416 D419 D420 D421 D501 D502 D503 D504 D505 D506 D508 D509 D510 D511 D512 D513 D514
Code No. 2401-001576 2401-000039 2401-000039 2301-000004 2301-000174 2401-000025 2401-000292 2201-000019 2202-002009 2401-000037 2401-000292 2401-000603 2401-000480 2401-001576 2301-000013 2201-000017 2202-002009 0203-001199 0203-001200 3711-000197 6042-000001 3711-000217 0401-000005 0402-000274 0401-000005 0402-000546 0402-000274 0402-000006 0402-000006 0402-000006 0402-000208 0402-000274 0402-000546 0402-000546 0402-000274 0402-000546 0401-000005 0401-000005 0401-000005 0402-000274 0401-000005 0401-000004 0401-000005 0402-000017 0402-000546 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000017 0401-000005 0402-000252
SNA SNA SNA SNA SNA
7-4
AN17K*/AN17L*
7 Electrical Parts List
CONFIDENTIAL
Description DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-ZENER DIODE-ZENER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET PIN HINGE PIN HINGE IC-EEPROM IC-POSI.ADJUST REG. IC-POSI.FIXED REG. CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS Specification 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UF4007,1KV,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UF4004,400V,1A,DO-41,TP 1N4148,100V,200mA,DO-35,TP UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH BRASS,D2.36!,HEAT/SINK,SN BRASS,D2.36!,HEAT/SINK,SN 524C80D41,4KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,ST 431,TO-92,3P,-,PLASTIC,2.44/2. 78DL05,TO-92,3P,4.5X4.5MM,PLASTIC,4.8/5.2V,625MW,-40TO+85C,150MA,-,TP 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. Remarks
Loc. No. D602 D604 D605 D606 D607 D610 D612 D613 D615 D616 D625 D626 D628 D629 D630 EY301 EY302 EY401 EY444 EY445 EY501 EY502 EY503 EY504 EY505 EY506 EY507 EY508 EY509 EY510 EY601 EY602 EY603 EY604 EY605 EY606 EY607 EY608 EY609 EY610 GT603 GT604 IC202 IC602 IC604 JP_DHHS JP1 JP10 JP11 JP12 JP14 JP15 JP16 JP17 JP18
Code No. 0401-000005 0402-000012 0402-000012 0402-000546 0401-000005 0402-000012 0402-000274 0401-000005 0403-000361 0403-000361 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 BH71-40300A BH71-40300A 1103-001149 1203-000002 1203-002653 BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U
SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
AN17K*/AN17L*
7-5
7 Electrical Parts List
CONFIDENTIAL
Description CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS Specification 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. Remarks
Loc. No. JP19 JP2 JP20 JP21 JP22 JP225 JP23 JP233 JP239 JP24 JP240 JP248 JP251 JP252 JP258 JP262 JP264 JP265 JP266 JP269 JP27 JP270 JP29 JP3 JP30 JP31 JP32 JP33 JP35 JP36 JP37 JP38 JP39 JP4 JP40 JP41 JP42 JP43 JP44 JP45 JP46 JP47 JP48 JP49 JP5 JP50 JP51 JP52 JP53 JP54 JP55 JP56 JP57 JP59 JP6
Code No. BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U
7-6
AN17K*/AN17L*
7 Electrical Parts List
CONFIDENTIAL
Description CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS PCB TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON Specification 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. AN17K*,FR1,1,1.6T,247*247,MAIN 2N3904,NPN,625mW,TO-92,TP,100-300 2N3906,PNP,625mW,TO-92,TP,100-300 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSC2383-Y,NPN,900000mW,TO-92L,TP,160-320 KSA733,PNP,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 2N5551,NPN,625mW,TO-92,TP,80-250 KSP42,NPN,625mW,TO-92,-,40 KSP42,NPN,625mW,TO-92,-,40 KSP42,NPN,625mW,TO-92,-,40 KSA733,PNP,250mW,TO-92,TP,120-240 2N6520,PNP,625mW,TO-92,TP,30-200 KSP44,NPN,625mW,TO-92,TP,50-200 KSC1008,NPN,800mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSD1616-Y,NPN,750mW,TO-92,TP,135-270 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM Remarks
Loc. No. JP60 JP61 JP62 JP63 JP64 JP65 JP66 JP67 JP68 JP69 JP7 JP70 JP71 JP73 JP74 JP75 JP76 JP78 JP79 JP8 JP80 JP81 JP84 JP85 JP86 JP87 JP9 MP1.0_MAIN Q301 Q302 Q303 Q401 Q403 Q405 Q406 Q407 Q414 Q415 Q416 Q420 Q502 Q551 Q601 Q602 Q604 Q609 Q610 Q611 Q613 Q614 R200 R201 R202 R203 R204
Code No. BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH41-00215A 0501-000122 0501-000581 0501-000586 0501-000586 0501-000372 0501-000303 0501-000303 0501-000140 0501-000412 0501-000412 0501-000412 0501-000303 0501-000143 0501-000413 0501-000010 0501-000586 0501-000404 0501-002228 0501-000586 0501-000586 0501-002228 0501-000586 2001-000869 2001-000290 2001-000290 2001-000008 2001-000008
AN17K*/AN17L*
7-7
7 Electrical Parts List
CONFIDENTIAL
Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-CARBON(S) R-CARBON(S) R-METAL R-METAL R-METAL R-METAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-CARBON R-CARBON R-CARBON(S) R-METAL OXIDE R-CARBON R-CARBON R-METAL OXIDE(S) R-METAL OXIDE(S) R-CARBON(S) Specification 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 270OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 15Kohm,1%,1/4W,AA,TP,2.4x6.4mm 4.7Kohm,1%,1/4W,AA,TP,2.4x6.4m 1OHM,5%,1/2W,AA,TP,2.4X6.4MM 470OHM,5%,1/2W,AA,TP,2.4X6.4MM 1.2ohm,2%,1/2W,AA,TP,3.3x9.0mm 5.1Kohm,1%,1/4W,AA,TP,2.4x6.4m 43Kohm,1%,1/4W,AA,TP,2.4x6.4mm 1.2ohm,2%,1/2W,AA,TP,3.3x9.0mm 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10OHM,5%,1/8W,AA,TP,1.8X3.2MM 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15OHM,5%,1/2W,AA,TP,2.4X6.4MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150Kohm,1%,1/4W,AA,TP,2.4x6.4m 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 2.2KOHM,5%,1/