Text preview for : HCD-DZ100.pdf part of Sony HCD-DZ100 Service manual for HCD-DZ100
Back to : HCD-DZ100.part1.rar | Home
HCD-DZ100
SERVICE MANUAL
Ver. 1.3 2005.11
US Model Canadian Model AEP Model UK Model E Model Australian Model
HCD-DZ100 is the amplifier, DVD/CD and tuner section in DAV-DZ100.
This system incorporates with Dolby*1 Digital and Dolby Pro Logic (II) adaptive matrix surround decoder and the DTS*2 Digital Surround System. *1 Manufactured under license from Dolby Laboratories. "Dolby," "Pro Logic," and the double-D symbol are trademarks of Dolby Laboratories. *2 Manufactured under license from Digital Theater Systems, Inc. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc.
AUDIO POWER SPECIFICATIONS for the US model
Model Name Using Similar Mechanism Mechanism Type Optical Pick-up Name
HCD-DZ300 CDM85-DVBU102 KHM-310CAA/C2NP
SPECIFICATIONS
Surround mode (reference) music power output Other models: NTSC/PAL Front: 120 W + 120 W Frequency response (at 2 CH STEREO mode) (with SS-TS31) DVD (PCM): 2 Hz to 22 POWER OUTPUT AND kHz (±1.0 dB) Center*: 120 W TOTAL HARMONIC CD: 2 Hz to 20 kHz (±1.0 (with SS-CT31) DISTORTION: With 3 ohm loads, both dB) Surround*: 120 W + 120 channels driven, from W 200 20,000 Hz; rated Tuner section (with SS-TS31B) 55 watts per channel System PLL quartz-locked digital Subwoofer*: 120 W minimum RMS power, synthesizer system (with SS-WS31) with no more than 0.7 % FM tuner section total harmonic distortion * Depending on the sound field settings and the source, Tuning range from 250 milli watts to there may be no sound output. North American model: 87.5 108.0 MHz rated output. Inputs (100 kHz step) VIDEO/SAT (AUDIO IN) Sensitivity: 250/450 mV Other models: Amplifier section 87.5 108.0 MHz Impedance: 50 kilohms (50 kHz step) North American model: (EXCEPT AEP, UK, RU) Antenna (aerial) FM wire antenna (aerial) Surround mode (reference) music power output Sensitivity: 450 mV Antenna (aerial) terminals 75 ohms, unbalanced TV Front: 120 W + 120 W 10.7 MHz Impedance: 50 kilohms Intermediate frequency (with SS-TS31) AM tuner section (AEP, UK, RU) Center*: 120 W Tuning range DVD system (with SS-CT31) North American, Latin, and Mexican models: Surround*: 120 W + 120 Laser Semiconductor laser 530 1,710 kHz (with the W (DVD: = 650 nm) interval set at 10 kHz) (with SS-TS31B) (CD: = 790 nm) 531 1,710 kHz (with the Subwoofer*: 120 W Emission duration: interval set at 9 kHz) (with SS-WS31) continuous Other models: Signal format system Stereo mode (rated) 55 W + 55 W (3 ohms at 1 North American, Latin, and Mexican models: kHz, DIN) NTSC -- Continued on next page --
SUPER AUDIO CD/DVD RECEIVER
9-879-674-04
2005K16-1 © 2005.11
Sony Corporation
Home Audio Division Published by Sony Engineering Corporation
HCD-DZ100
Ver. 1.2
Middle eastern models: Other models:
Antenna (aerial) Intermediate frequency
531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) 531 1,602 kHz (with the interval set at 9 kHz) AM loop antenna (aerial) 450 kHz
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
Video section
Outputs Video: 1 Vp-p 75 ohms S video: Y: 1 Vp-p 75 ohms C: 0.286 Vp-p 75 ohms COMPONENT: Y: 1 Vp-p 75 ohms
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270 °C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
PB/CB, PR/CR: 0.7 Vp-p 75 ohms
(EXCEPT AEP, UK, RU) Video: 1 Vp-p 75 ohms R/G/B: 0.7 Vp-p 75 ohms (AEP, UK, RU)
General
Power requirements North American and Mexican models: 120 V AC, 60 Hz Central/South American models: 110 240 V AC, 50/60 Hz Taiwan model: 120 V AC, 50/60 Hz Korean model: 220 V AC, 60 Hz Other models: 220 240 V AC, 50/60 Hz Power consumption On: 135 W Standby: 0.3 W (at the Power Saving mode) Dimensions (approx.) 430 × 70 × 295 mm (17 × 2 7/8 × 11 5/8 inches) (w/h/d) incl. projecting parts Mass (approx.) 3.6 kg (7 lb 15 oz) Design and specifications are subject to change without notice.
MODEL IDENTIFICATION Rear Panel
Parts No.
Model AEP, UK models RU model EA model SP model CND model AUS model KR model E32 model MX model US model · Abbreviation AUS : Australian model CND : Canadian model E32 : 110-240V AC area in E model EA : Saudi Arabia model KR MX RU SP Part No. 2-588-951-0[] 2-588-951-1[] 2-588-951-2[] 2-588-951-3[] 2-588-951-4[] 2-588-951-5[] 2-588-951-6[] 2-588-951-7[] 2-588-951-9[] 2-634-883-1[] : Korean model : Mexican model : Russian model : Singapore model
2
HCD-DZ100
Ver. 1.2
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
TABLE OF CONTENTS 1. 2. 3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10. 3-11.
SERVICING NOTE ................................................... 4 GENERAL ................................................................... 6 DISASSEMBLY
Disassembly Flow ........................................................... Case, Front Panel Assy .................................................... FL Board .......................................................................... KEY Board, STBY Board ............................................... I/O Board, DC Fan .......................................................... DMB11 Board ................................................................. MAIN Board .................................................................... DVD Mechanism Deck (CDM85-DVBU102) ................ Tray .................................................................................. Belt, MS-203 Board ........................................................ Optical Pick-up (KHM-310CAA/C2NP) ........................ 10 11 12 12 13 13 14 15 15 16 17
4. 5.
5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. 5-9. 5-10. 5-11. 5-12. 5-13. 5-14. 5-15. 5-16. 5-17. 5-18. 5-19. 5-20. 5-21. 5-22. 5-23. 5-24. 5-25. 5-26. 5-27. 5-28.
TEST MODE ............................................................... 18 DIAGRAMS
Block Diagram RF/SERVO Section ......................... Block Diagram VIDEO Section ............................... Block Diagram AMP Section ................................... Block Diagram AUDIO Section ............................... Block Diagram POWER Section .............................. Printed Wiring Board DMB11 Board (Side A) ........ Printed Wiring Board DMB11 Board (Side B) ........ Schematic Diagram DMB11 Board (1/5) ................. Schematic Diagram DMB11 Board (2/5) ................. Schematic Diagram DMB11 Board (3/5) ................. Schematic Diagram DMB11 Board (4/5) ................. Schematic Diagram DMB11 Board (5/5) ................. Printed Wiring Board MAIN Section (Side A) ........ Printed Wiring Board MAIN Board (Side B) ........... Schematic Diagram MAIN Board (1/7) ................... Schematic Diagram MAIN Board (2/7) ................... Schematic Diagram MAIN Board (3/7) ................... Schematic Diagram MAIN Board (4/7) ................... Schematic Diagram MAIN Board (5/7) ................... Schematic Diagram MAIN Board (6/7) ................... Schematic Diagram MAIN Board (7/7) ................... Printed Wiring Board PANEL Section ..................... Schematic Diagram PANEL Section ....................... Printed Wiring Board I/O Board .............................. Schematic Diagram I/O Board (1/2) ........................ Schematic Diagram I/O Board (2/2) ........................ Printed Wiring Board MS-203 Board ....................... Schematic Diagram MS-203 Board ......................... 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 50
0.15 µF
1.5 k
AC voltmeter (0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
6.
6-1. 6-2. 6-3. 6-4.
EXPLODED VIEWS
Overall Section ................................................................ Front Panel Section ......................................................... Chassis Section ................................................................ DVD Mechanism Deck Section (CDM85-DVBU102) ... 63 64 65 66
7.
ELECTRICAL PARTS LIST .................................. 67
3
HCD-DZ100 SECTION 1 SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the "S curve check" in "CD section adjustment" and check that the S curve waveform is output several times. DISC SLOT LOCK The disc slot lock function for the antitheft of an demonstration disc in the store is equipped. Setting Procedure : 1. Press the ?/1 button to turn the set on. 2. Press the [FUNCTION] button to set DVD function. 3. Insert a disc. 4. Press the x stick and the A button simultaneously for five seconds. 5. The message "LOCKED" is displayed and the slot is locked. Releasing Procedure : 1. Press the x stick and the A button simultaneously for five seconds again. 2. The message "UNLOCKED" is displayed and the slot is unlocked.
Note: Note 1: When "LOCKED" is displayed, the slot lock is not released by turning power on/off with the ?/1 button. Regarding the notification symbol "R" Because the number of the operating buttons of this product are limited, some operations require use of the operating buttons of the remote commander, When a specific operation requires use of the operating buttons of the remote commander, "R" is added to the specific operating procedure in this manual. Example MENU/NO "R" The MENU/NO button of remote commander. Incorrect operations may be performed if the test mode ia not entered properly. In this case, press the ?/1 button to turn the power off, and retry to enter the test mode. If the disc tray does not open and the message "LOCKED" appears, press the x stick and the A button simultaneously for seconds or longer. Then remove your fingers from the above stick and the button. The message "UNLOCKED" appears for 2 seconds and the disc tray opens.
Note 2:
Note 3:
Self-diagnosis Function
(When letters/numbers appear in the display)
When the self-diagnosis function is activated to prevent the system from malfunctioning, a 5character service number (e.g., C 13 50) with a combination of a letter and 4 digits appears on the screen and the front panel display. In this case, check the following table.
C:13:50
Note on DMB11 board replacement
New part of EEP ROM (IC103) on the DMB11 board cannot be used. Therefore, if the mounted DMB11 board (A-1121-906-A, etc.) is replaced, exchange new EEP ROM (IC103) with that used before the replacement.
First 3 characters of the service number
Cause and/or corrective action
C 13 C 31
The disc is dirty. ,Clean the disc with a soft cloth The disc is not inserted correctly. ,Restart the system, then re-insert the disc correctly.
E XX To prevent a malfunction, the (xx is a number) system has performed the selfdiagnosis function. ,Contact your nearest Sony dealer or local authorized Sony service facility and give the 5character service number. Example: E 61 10
4
HCD-DZ100
· SERVICE POSITION (DMB11 BOARD)
When servicing side B of the DMB11 board Remove the DMB11 board from bracket. (Refer to DISASSEMBLY 3-6. (page 13)). Set the DMB11 board facing the side B upward as shown. Connect the cable and make the repair work.
DMB11 board (side B)
DMB bracket
5
HCD-DZ100 SECTION 2 GENERAL
This section is extracted from instruction manual.
Front panel
A "/1 (on/standby) (20, 24, 62) B Disc tray (24) C A (open/close) (24, 62) D H (play) (24) E X (pause) (24) F x (stop) (24, 62)
G ./> (24) H FUNCTION (24) I VOLUME (24) J (remote sensor) (12) K Front panel display (80)
6
HCD-DZ100
Rear panel
(EXCEPT AEP, UK, RU)
VIDEO/SAT R AUDIO IN L
COMPONENT VIDEO OUT DVD ONLY Y P B /C B P R /C R
S VIDEO (DVD ONLY)
AM
FRONT R FRONT L SURR R SURR L CENTER WOOFER
VIDEO
MONITOR OUT
SPEAKER
COAXIAL
FM 75
A SPEAKER jacks (14) B VIDEO/SAT AUDIO IN jacks (21, 24) C COMPONENT VIDEO OUT jacks (19)
D MONITOR OUT (VIDEO / S VIDEO) jacks (19) E AM terminal (18) F FM 75 COAXIAL jack (18)
Rear panel (AEP, UK, RU)
EURO AV
AM
FRONT R
FRONT L
SURR R
SURR L
CENTER
WOOFER
OUTPUT(TO TV)
SPEAKER
COAXIAL
FM 75
A SPEAKER jacks (14) B EURO AV T OUTPUT (TO TV) jacks (19)
C AM terminal (18) D FM 75 COAXIAL jack (18)
7
HCD-DZ100
Remote (EXCEPT AEP, UK, RU)
J TOP MENU (33) K C/X/x/c/ENTER (25, 31, 51, 55, 61, 65, 66) L O RETURN (34) M O m/ REPLAY, STEP (29) SLOW, TUNING (42, 62) N . PRESET , TV CH (26, 29, 59, 63) P H (play) (29) The H button has a tactile dot.* Q TV (59) R THEATRE SYNC (60) S "/1 (on/standby) (25, 29, 63) T AMP MENU (25, 61, 65) U DSGX (53) V FUNCTION (20, 29, 53, 61) W SOUND FIELD (51) X DISPLAY (63) Y PICTURE NAVI (38) wh AUDIO (49) wj SUBTITLE (54) wk ANGLE (54) wl ALBUM /+ (29, 60) e; MENU (33) ea MUTING (29) es VOLUME, TV VOL +/ (29, 59, 63)
The VOLUME, TV VOL + button has a tactile dot.*
ed DISPLAY (9, 26, 31, 55, 66) ADVANCE, STEP (29) SLOW, TUNING + (42, 62) ef > PRESET +, TV CH + (26, 29, 59, 63) eg eh M/ A TV [/1 (on/standby) (59) B TV/VIDEO (59) C TUNER MENU (62) D SLEEP (64) E PROGRESSIVE (20) F REPEAT/FM MODE (32, 63) G TUNER/BAND (63) H Number buttons (33, 55, 59)
ej x (stop) (29, 55, 63) ek X (pause) (29)
* Use the tactile dot as a reference when operating the system.
The number 5 button has a tactile dot.*
I CLEAR, - (26, 31, 59, 60)
8
HCD-DZ100
Remote (AEP, UK, RU)
J C/X/x/c/ENTER (20, 26, 49, 53, 62, 63) K O RETURN (29) L N m/ REPLAY, STEP (24) SLOW, TUNING (39, 59) M . PRESET , TV CH (21, 24, 57, 60) O H (play) (24) The H button has a tactile dot.* P TV (57) Q THEATRE SYNC (58) R "/1 (on/standby) (20, 24, 60) S AMP MENU (20, 62) T DSGX (51) U FUNCTION (24) V SOUND FIELD (49) W DISPLAY (60) X PICTURE NAVI (33) wg AUDIO (47) wh SUBTITLE (52) wj ANGLE (52) wk ALBUM /+ (24, 58) wl MENU (28) e; MUTING (24) ea VOLUME, TV VOL +/ (24, 57, 60)
The VOLUME, TV VOL + button has a tactile dot.*
es DISPLAY (9, 21, 26, 53, 63) ADVANCE, STEP (24) SLOW, TUNING + (39, 59) ed > PRESET +, TV CH + (21, 24, 57, 60) ef eg M/
eh x (stop) (24, 53, 60) ej X (pause) (24) A TV [/1 (on/standby) (57) B TV/VIDEO (57) C TUNER MENU (59) D SLEEP (61) E REPEAT/FM MODE (27, 60) F TUNER/BAND (60) G Number buttons (28, 53, 57)
* Use the tactile dot as a reference when operating the system.
The number 5 button has a tactile dot.*
H CLEAR, - (21, 26, 57, 58) I TOP MENU (28)
9
HCD-DZ100 SECTION 3 DISASSEMBLY
3-1. DISASSEMBLY FLOW
· This set can be disassembled in the order shown below.
SET
3-2. CASE, FRONT PANEL ASSY (Page 11)
3-3. FL BOARD (Page 12)
3-6. DMB11 BOARD (Page 13)
3-5. I/O BOARD, DC FAN (Page 13)
3-4. KEY BOARD, STBY BOARD (Page 12)
3-8. DVD MECHANISM DECK (CDM85-DVBU102) (Page 15)
3-7. MAIN BOARD (Page 14)
3-9. TRAY (Page 15)
3-11. OPTICAL PICK-UP (KHM-310CAA/C2NP) (Page 17)
3-10. BELT, MS-203 BOARD (Page 16)
10
HCD-DZ100
Note: Follow the disassembly procedure in the numerical order given.
3-2. CASE, FRONT PANEL ASSY
4 screw (CASE3 TP2)
6 five screws (+BV 3)
7 case
5 screw (CASE3 TP2) 9 claw
qa wire (flat type) 19core (CN509)
0 claw
3 DVD lid qs front panel assy
8 three screws (+BV 3) 1 The lever is moved in the direction of the arrow with the thin rod.
DVD lid
2
11
HCD-DZ100
3-3. FL BOARD
1 knob (vol) 2 nut 8 FL board
6 screw (+BVTP 2.6) 5 shield (front)
3 two sheets
earth line
4 three screws (+BVTP 2.6) 7 wire (flat type) 19core (CN801)
3-4. KEY BOARD, STBY BOARD
8 button (power)
5 two tapping screws (+BVTP 2.6)
7 STBY board 4 button (play) 1 four tapping screws (+BVTP 2.6)
6 two tapping screws (+BVTP 2.6)
3 KEY board
2 four tapping screws (+BVTP 2.6)
12
HCD-DZ100
3-5. I/O BOARD, DC FAN
3 wire (flat type) 13core (CN201)
4 wire (flat type) 23core (CN601)
qs I/O board
qa wire (flat type) 11core or 9core (CN101) qf tuner unit
qd two screws (+BV 3)
2 connector (CN300) 1 connector (CN901) 9 DC fan 7 back panel
q; two screws (+BV 3) (AEP,UK and Russian models) q; two screws (+BV 3) (Other models) 6 three screws (+BV 3) 8 two screws (BVTT 4 × 8) 5 three screws (+BV 3)
3-6. DMB11 BOARD
4 wire (flat type) 24core (CN101) 3 connector (CN201)
5 wire (flat type) 13core (CN301) 6 wire (flat type) 7core (CN302)
9 two screws (+BV 3)
0 two screws (+BV 3)
2 wire (flat type) 5core (CN202) 1 wire (flat type) 13core (CN106)
qa DMB11 board
7 wire (flat type) 11core (CN4501) 8 connector (CN401)
13
HCD-DZ100
3-7. MAIN BOARD
2 screw (BVTP 3 × 12)
1 two screws (+BV 3)
3 heat sink (AMP)
5 wire (flat type) 7core (CN503) 6 wire (flat type) 23core (CN507) 7 wire (flat type) 11core (CN504)
4 wire (flat type) 11core (CN505) 9 five screws (+BV 3)
8 four screws (+BV 3) 0 MAIN board
14
HCD-DZ100
3-8. DVD MECHANISM DECK (CDM85-DVBU102)
1 three screws (+BV 3)
2 dmb bracket
3 three screws (+BV 3)
5 DVD mechanism deck (CDM85-DVBU102)
4 wire (flat type) 5core
3-9. TRAY
1 Move the chuck cam in the direction of the arrow.
bottom side
3 two claws 2
4 5 tray
15
HCD-DZ100
3-10. BELT, MS-203 BOARD
2 chuck cam
3 belt
1 two claws
4 screw (M 1.7 × 2.5)
7 MS-203 board
6 DC motor
5 three claws
16
HCD-DZ100
3-11. OPTICAL PICK-UP (KHM-310CAA/C2NP)
2 chuck cam
3 two claws
1 two claws
4 base unit
8 two insulators
6 four insulator screws
9 two insulators
0 optical pick-up (KHM-310CAA/C2NP)
5 two claws 7 bu holder
17
HCD-DZ100 SECTION 4 TEST MODE
Note 1: Regarding the notification symbol "R" Because the number of the operating buttons of this product are limited, some operations require use of the operating buttons of the remote commander, When a specific operation requires use of the operating buttons of the remote commander, "R" is added to the specific operating procedure in this manual. Example MENU/NO "R" The MENU/NO button of remote commander. Incorrect operations may be performed if the test mode is not entered properly. In this case, press the ?/1 button to turn the power off, and retry to enter the test mode.
Note 2:
1. Cold Reset · The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customers. Procedure: 1. Press the ?/1 button to turn the power on. 2. Press three buttons x , A and ?/1 simultaneously. 3. When this button is operated, display as "COLD RESET" for a while and all of the settings are reset. 2. Panel Test Mode · This mode is used to check the software version, LCD, LED and keyboard. 2-1. DVD LED Test Mode Procedure: 1. Press the ?/1 button to turn on the power. 2. Press three bottons X , . and A simultaneously. 3. When the display LED test mode is activated, all segments are turned on. 4. To exit from this mode, pull out the AC plug. 2-2. Version Test Mode Procedure: 1. When the panal test mode is activated, press the . button and the message "DS1***" is displayed, the version test mode is activated. 2. Whenever press the . button, the version is displayed in order of CC2, MC, SYS, UI, DVD, TA, TM and DS1. 3. Press the > button and the date of the softwafe production is displayed. 4. Press the > button again and the version is displayed. 5. To exit from this mode, pull out the AC plug. 2-3. Key Test Mode Procedure: 1. When the panel test mode is activated, press the H button, to select the key test mode. 2. To enter the KEY test mode, the fluorecent indicator displays "K0 VO". Each time a button is pressed, "KEY" value increases. However, once a button is pressed, it is no longer taken into account. When all keys are pressed correctly, "K8 VO" is displayed. 3. To exit from this mode, pull out the AC plug.
3. Disc Tray Lock The disc tray lock function for the antitheft of an demonstration disc in the store is equipped. Setting Procedure : 1. Press the ?/1 button to turn the set on. 2. Press the FUNCTION button to set DVD function. 3. Insert a disc. 4. Press the x button and the A button simultaneously for five seconds. 5. The message "LOCKED" is displayed and the tray is locked. Releasing Procedure : 1. Press the x button and the A button simultaneously for five seconds. again. 2. The message "UNLOCKED" is displayed and the tray is unlocked.
Note: When "LOCKED" is displayed, the slot lock is not released by turning power on/off with the ?/1 button.
4. DVD Ship Mode · Use this mode when returning the set to the customer after repair. Procedure: 1. Press the ?/1 button to turn the set on. 2. Press the FUNCTION button to set the function "DVD". 3. Press three buttons x , and ?/1 simultaneously. 4. After a message "MECHA LOCK" is displayed on the fluorescent indicator tube, pull out the AC plug. 5. To exit from this mode, press the ?/1 button to turn the set on. 5. DVD Debug In Mode Procedure: 1. Press the ?/1 button to turn the set on. 2. Press the FUNCTION button to set the function "DVD". 3. Press the three buttons . , A and > simultaneously. 4. To exit from this mode, press the ?/1 button to turn the set on. 6. AM Step Change · A step of AM channels can be changed over between 9 kHz and 10 kHz. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function "TUNER", and press FUNCTION button to select the BAND "AM". 3. Press ?/1 button to turn the set OFF. 4. Press > and ?/1 buttons simultaneously, and the display of fluorescent indicator tube changes to "AM 9 k STEP" or "AM 10 k STEP", and thus the channel step is changed over.
18
HCD-DZ100
Ver. 1.3
DVD SECTION [TEST DISC LIST]
Be sure to use the DVD disc that matches the signal standards of your region. · CD YEDS-18 (Part No.: 3-702-101-01) PATD-012 (Part No.: 4-225-203-01) · DVD SL (Single Layer) NTSC : HLX-503 (Part No.: J-6090-069-A) HLX-504 (Part No.: J-6090-088-A) PAL : HLX-506 (Part No.: J-6090-077-A) · DVD DL (Dual Layer) NTSC : HLX-501 (Part No.: J-6090-071-A) HLX-505 (Part No.: J-6090-089-A) PAL : HLX-507 (Part No.: J-6090-078-A) 4-1. GENERAL DESCRIPTION The Mirror Time and IOP measurement allows you to make diagnosis and adjustment simply by using the remote commander and monitor TV. The instructions, diagnosis results, etc. are given on the on screen display (OSD). The Mirror Time and IOP measurement is required is such events where servicing a DVD-Player includes changing the Base Unit (BU). For each new BU to be used with a certain MV-044 board, Mirror Time and IOP measurement need to be carried out. 4-2. STARTING TEST MODE Press three buttons x , A and VOLUME + simultaneously with the DVD player in standby mode. The Test Mode starts, then the menu shown below will be displayed on the TV screen.
Remocon Diagnosis Menu 0. 1. 2. 3. 4. 5. External Chip Check Servo Parameter Check Drive Manual Operation Emergency History Version Information Video Level Adjustment
4-4. MIRROR TIME ADJUSTMENT To enter Mirror Time Adjustment, press 5 "R" button on the remote commander. The screen will appear as below.
MIRR time Adjust Menu 1. 2. 3. 4. 5. CD MIRR time Check: DVD MIRR time Check: Threshold: Save to EEPROM Default set MIRR time
[Open] Tray open [Close] Tray close [0] Return to previous menu
There are five main commands in the Mirr time Adjust menu as shown in the figure above. The functions of each command are described in the following page. 1. CD MIRR time Check This command checks the Mirror time value for CD disc. 2. DVD MIRR time Check This command checks the Mirror time value for DVD disc. 3. Threshold This command displays the threshold value between CD and DVD mirror time. 4. Save to EEPROM This command saves an adjusted mirror time value to the EEPROM. 5. Default set MIRR time This command will set CD and DVD mirror time to firmware default value. [Open] / [Close] Pressing the A button controls the tray for disc change during mirror time adjustment. [0] Return to previous menu Press 0 "R" button to return to previous menu. 4-4-1. EXECUTING MIRROR TIME ADJUSTMENT In order to execute mirror time adjustment, the following standard procedures must be followed. (1) In standby mode, press three buttons x , A and VOLUME + simultaneously. (2) Select "2. Drive Manual Operation".
Remocon Diagnosis Menu 0. 1. 2. 3. 4. 5. External Chip Check Servo Parameter Check Drive Manual Operation Emergency History Check Version information Video Level Adjustment : DS1_xx : Ver. xx.xx (xxxx) : Ver. x.xxx
Model Name : DS1_XX IF-con : Ver. xx.xx (xxxx) Syscon : Ver. x.xxx
The menu above is the Remocon Diagnosis Menu screen which consists of six main function. At the bottom of the menu screen, the model name and IF-con version. To enter Mirror Time Adjustment menu, press button 2 "R" on the remote commander to enter Drive Manual Operation menu. To exit from the Test Mode, press the power button on the remote commander. 4-3. DRIVE MANUAL OPERATION The Drive Manual Operation menu consists of five main function. By pressing 2 "R" button on the remote commander in the Remocon Diagnosis Menu, the screen will appear as below.
Drive Manual Operation 1. 2. 3. 4. 5. 0. Servo Control Track/Layer Jump Manual Adjustment Tray Aging Mode MIRR time Adjust Return to Top Menu
Model IF-con Syscon
19
HCD-DZ100
(3) Select "5. MIRR time Adjust".
Drive Manual Operation
(14) Confirm the same values are displayed. If it is not same, return to step 7.
MIRR time Adjust Menu
1. 2. 3. 4. 5. 0.
Servo Control Track/Layer Jump Manual Adjustment Mecha test mode MIRR time Adjust Return to Top Menu
1. 2. 3. 4. 5.
CD MIRR time Check: DVD MIRR time Check: XX XX Threshold: Save to EEPROM: Default set MIRR time:
(4) Select "5. Default set MIRR time".
MIRR time Adjust Menu 1. 2. 3. 4. 5. CD MIRR time Check: DVD MIRR time Check: Threshold: Save to EEPROM: Default set MIRR time:
[Open] Tray open [close] Tray close [0] Return to previous menu
(15) Push A button to eject tray. (16) Take out HLX-504 and insert Test Disc YEDS-18 into tray. (17) Push A button to close tray.
[Open] Tray open [Close] Tray close [0] Return to previous menu
(18) Push "1. CD MIRR time check". (19) Wait for HEX number to display. (20) Confirm the number, if YY is 5A ~ E8, proceed with next step. If no, return to 15.
MIRR time Adjust Menu 1. 2. 3. 4. 5. CD MIRR time Check: yy YY DVD MIRR time Check: XX XX Threshold: Save to EEPROM: Default set MIRR time:
(5) Select "3. Threshold". (6) Confirm the number. If it is 7D, go to next step. If it is any other value, return to step 4.
MIRR time Adjust Menu 1. 2. 3. 4. 5. CD MIRR time Check: DVD MIRR time Check: Threshold: 7D Save to EEPROM: Default set MIRR time:
[Open] Tray open [Close] Tray close [0] Return to previous menu
[Open] Tray open [close] Tray close [0] Return to previous menu
(7) Push A button to eject tray. (8) Insert Test Disc HLX-504 into tray. (9) Push A button to close tray.
(21) Push "4. Save to EEPROM". (22) Confirm the same values are displayed. If it is not the same, return to step 15.
MIRR time Adjust Menu
(10) Push "2. DVD MIRR time Check". (11) Wait for HEX number to display. (12) Confirm the number, if XX is 28 ~ 70, proceed with next step. If no, return to 8.
MIRR time Adjust Menu 1. 2. 3. 4. 5. CD MIRR time Check: DVD MIRR time Check: xx xx Thereshold: Save to EEPROM: Default set MIRR time:
1. 2. 3. 4. 5.
CD MIRR time check: YY YY DVD MIRR time check: XX XX Threshold: Save to EEPROM: Default set MIRR time:
[Open] Tray open [close] Tray close [0] Return to previous menu
(23) Push A button to eject tray. (24) Remove Test Disc YEDS-18 from tray. (25) Push A button to close tray.
[Open] tray open [close] Tray close [0] Return to previous menu
(26) Press 0 "R" button to the Drive Manual Operation menu. (27) Press 0 "R" button to return to the Remocon Diagnosis Menu. (28) Press the ?/1 button to switch OFF set.
(13) Push "4. Save to EEPROM".
20
HCD-DZ100
4-5. EXECUTING IOP MEASUREMENT In order to execute mirror time adjustment, the following standard procedures must be followed. (1) In standby mode, press three buttons x , A and VOLUME + simultaneously.
Remocon Diagnosis Menu 0. 1. 2. 3. 4. 5. External Chip Check Servo Parameter Check Drive Manual Operation Emergency History Check Version information Video Level Adjustment
(5) Wait until a hexadecimal number appear.
Manual Adjust 1. 2. 3. 4. 5. 6. 7. 8. 9. 0. Track Balance Adjust: Track Gain Adjust: Focus Balance Adjust: Focus Gain Adjust: Eq Boost Adjust: Iop. 5B: TRV. Level: S curve(FE) Level: RFL(PI) Level: MIRR Time:
Change Value [0] Return to previous menu
Model : DS1 XX IF-con Ver : XX.XX (XXXX) Syscon Ver : X.XX
(6) Convert each data from hexadecimal to decimal using conversion table. (7) Substract between these two values. (8) If the remainder is smaller than 93 (decimal), then it is OK. However if the value is higher than 93, then the BU is defective and need to be change. (9) Press RETURN "R" button to return back to previous menu. (10) Press 0 "R" button to return to Top Menu and power OFF the DVD Player.
(2) Select "2. Drive Manual Operation" by pressing the 2 "R" button on the remote commander. The screen will appear as below.
Drive Manual Operation 1. 2. 3. 4. 5. 0. Servo Control Track/Layer Jump Manual Adjustment Tray Aging Mode MIRR time adjust Return to top Menu
(3) Select "3. Manual Adjustment" by pressing the 3 "R" button on the remote commander. The screen will appear as below.
Manual Adjust 1. 2. 3. 4. 5. 6. 7. 8. 9. 0. Track Balance Adjust: Track Gain Adjust: Focus Balance Adjust: Focus Gain Adjust: Eg boost Adjust: Iop: TRV. Level: S curve(FE) Level: RFL(PI) Level: MIRR Time:
o O Change Value [RETURN] Return to previous menu
(4) Select Iop by pressing 6 "R" button on the remote commander.
21
HCD-DZ100
Ver. 1.1
SECTION 5 DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
For Schematic Diagrams. Note: · All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. · f : internal component. · C : panel designation.
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
For Printed Wiring Boards. Note: · X : parts extracted from the component side. · a : Through hole. : Pattern from the side which enables seeing. · (The other layers' patterns are not indicated.) Caution: Pattern face side: (SIDE A) Parts face side: (SIDE B) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
· Indication of transistor.
C Q These are omitted.
BC E
These are omitted
IC103 is a written in and settled EEPROM. Supply with a single article has not been carried out. In case you exchange by DMB11 board, please put on IC103 currently used with the model again. · A : B+ Line. · B : B Line. · Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. · Voltages and waveforms are dc with respect to ground in service mode. · Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. no mark : DVD STOP · Voltages are taken with VOM (Input impedance 10 M). · Circled numbers refer to waveforms. · Signal path. F : AUDIO J : CD PLAY c : DVD PLAY I : SACD PLAY d : TUNER L : VIDEO E :Y a : CHROMA r : COMPONENT VIDEO q : R, G, B f : AUDIO IN (SAT) · Abbreviation AUS : Australian model CND : Canadian model E32 : 110-240V AC area in E model EA : Saudi Arabia model KR : Korean model MX : Mexican model RU : Russian model SP : Singapore model
B E
22
HCD-DZ100
· Circuit Boards Location
MEMO
TUNER UNIT DMB11 board I/O board
MAIN board
STBY board MS-203 board
FL board KEY board
HCD-DZ100
23
23
HCD-DZ100
5-1. BLOCK DIAGRAM RF/SERVO SECTION
RF
6 DVDRFIP OSP 252 253 OSN
DETECTOR
A B C D F E A B D C
D C B A
2 3 4 5
DVDA DVDB DVDC DVDD
19 TPI 18 TNI 8 9 10 11 NA NB MD MC
OPTICAL PICK-UP BLOCK (KHM-310CAA/C2NP) 176 LI M SW LASER DIODE (FOR CD) CD LD Q102 (1/2) AUTOMATIC POWER CONTROL (FOR CD)
IC102 (1/3) CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP DVD SYSTEM PROCESSOR DIGITAL SERVO PROCESSOR
· Signal Path
: CD PLAY : DVD PLAY : SACD PLAY
23 LD01
PD LASER DVD LD DIODE (FOR DVD) WR650 VR780 Q102 (2/2) AUTOMATIC POWER CONTROL (FOR DVD)
20 MD12 21 MD11 22 LD02
PRST 110
43 MTK_XRST
IFCK 99 MAMUTE IFSDO IFSDI XIFCS 51 98 101 100
33 DVD_SCO/CLK1 25 32 31 39 MAMUTE DVD_SOD/RXD1 DVD_SID/TXD1 DVD_XIFCS
Q101, Q103 VOLUME CONTROL
187 MSW
IC201 FOCUS/TRACKING COIL DRIVER, SPINDLE, SLED MOTOR DRIVER 42 41 FCS+ FCS TRK+ TRK +3.3V VCC 32 31 30 29 SLED MOTOR DRIVE SLED MOTOR DRIVE
OCSW 177 IFBSY 105 CKSW 179
42 SEN 34 DVD_IFBUSY/RST1
BUFFER
15 43 V1P4
39 TROPENPWN
IC509 (1/4) SYSTEM CONTROLLER
2AXIS DEVICE FOCUS/ TRACKING COIL
36 37 32 35 34
FOCUS COIL DRIVE TRACKING COIL DRIVE
48 1 3 4 10 13 16 17 40 45 19 20 22 21 25 22 24
FOO
FMO 38 FMO FOO 42 FOO DMO 37 DND TRO 41 TRO V1P4 30 V REFO 186 FWD 185 REV 40 IOPMON 47 SPFG 184 MUTE123 183 MUTE 181 TSDM S001 (CHUCK/TRAY DETECT) OCSW1 CKSW1 LDM+ LDM-
TRO FMO DMO
(SLED MOTOR)
M
SL SL+
(SPINDLE MOTOR)
M
SP+ SP
27 28 47 46
SPINDLE MOTOR DRIVE
BUFFER
M
(LOADING MOTOR)
HCD-DZ100
24
24
HCD-DZ100
5-2. BLOCK DIAGRAM VIDEO SECTION
AEP,UK,RU
J203 CROUT CYOUT CBOUT IC201 VIDEO AMP, 75ohm DRIVER VOUT 15 11 7 19 16 CYOUT 20 CBOUTB 18 CROUTB 16 CYOUT 8 CBOUT L CROUT R 2 6 R/C OUT G OUT B OUT V/Y OUT BLANK OUT FUNCTION SW A(L) IN A(R) IN EURO AV OUTPUT (TO TV)
WIDE DVD SEL
Q204, 205 FUNCTION SWITCH
RGB SEL DVD SEL
Q206-208, 210 BLANKOUT SWITCH
RGB 169
VOUT 30
EXCEPT AEP,UK,RU
J201 VIDEO YUV1 200 6 YIN
COUT 26
1 2
L, R
C
AMP SECTION (Page 26)
YUV2 196
2 CIN
S VIDEO (DVD ONLY)
AV SEL2
YUV1 194
4 CVBSIN
YOUT 21
YUV4 200 YUV5 202 YUV6 203 WIDE 171
10 CYIN 12 CBIN 14 CRIN 25 SI Y J202
MUTE1 MUTE2
PB/CB PR/CR
COMPONENT VIDEO OUT
3 13
AV SEL1
AV SEL1-2
B
AMP SECTION (Page 26)
IC102(2/3) DVD SYSTEM PROCESSOR
SCL SDA
IOCS IOUE IOWA
102 103
AB0 AB7 81-84,86-88,91 HD0 HD7
RD0 RD15 125-123, 121, 120, 118, 117, 115, 135, 133-128, 126
53-61, 67-72, 74-76, 78, 89, 92, 93 A0 A21
77 79 66
CE OE WE
146, 147, 149-151, 158-160, 162, 164-166
143 145
BA0 BA1
RA0 RA11
156 142138140139 113 137 157
6 5
SCL SPA
DATA & ADDRESS BUS 2,4,5,7,8,10,11,13,42,44,45,47,48,50,51,53 RD0 RD15
DRCLK RCS RWE RAS CAS DQM0 DQM1 DRCLE BS0 BS1
22-26, 29-35 RA0 RA11 IC104 SDRAM
20 21
38 19 16 18 17 15 39 37
IC103 EEPROM
DATA & ADDRESS BUS
A1-A20 A0
RCLK RCS RWE MRAS CAS MDQM0 MDQM1 CLE
HIGHA0-7 IOA0-7, IOA18-IOA20 A16, A17
· Signal Path : AUDIO
CE OE WE
HD0 HD7
: VIDEO :Y : COMPONENT VIDEO : R, G, B : CHROMA
29,31,33,35,38,40,42,44 DQ0 DQ7
45 DQ15/A-1
25-16, 9-1, 48 A0 A19 IC101 FLASH ROM
26 28 11
CE OE WE
HCD-DZ100
25
25
HCD-DZ100
5-3. BLOCK DIAGRAM AMP SECTION
IC3601 A/D CONVERTER 1 LIN DOUT 12 5 R-CH 2 RIN SCKI 15 BCK 11 6 9 8 7 ALRCK 213 ABCK 214 ACLK 215
IC4501 BUFFER 15 14 11 12 13 LRCKO BCKO D1 D2 D3 1 A 2 B 6 A/B G 7 Y 5 D2 D1 - D3, SCK, BCKO, LRCKO
A
AUDIO SECTION (Page 27)
IC503 SELECTOR
209 SPDATA/SMSDI
229 XTALI X101 27MHz 228 XTALO
ASDATA0 217 ASDATA1 218 ASDATA2 219 2 A
IC4502 BUFFER SCK
Y 4
EXCEPT AEP,UK,RU J200 SAT AUDIO L R R-CH IC602 AUDIO INPUT SELECTOR 12 X0 11 X3 14 X1 R-CH AEP,UK RDS-CLK RDS-DATA TUDI TUDO TUCLK TCE TUNED
IC102(3/3) DVD SYSTEM PROCESSOR
FM/AM TUNER UNIT COAXIAL FM 75 FM ANT GND AM ANT AM GND L-CH R-CH RDS-CLK RDS-DATA DI DO CK CE TUNED
X 13
IC603 AMP
A B 10 9 Q603 Q604 AEP,UK RDS-CLK 75 RDS-CLK/MIC-CLK RDS-DATA 76 RDS-DATA/MIC-DATA TUDO TUCLK TCE TUNED AV SEL0 AV SEL1 AV SEL2 78 80 77 79 85 PLL_DO PLL_DI PLL_CLK PLL_CE TUNED 100
M-ST WMUTE
AV SEL0
AV SEL2
· R-CH is omitted due to same as L-CH. · Signal Path : AUDIO : AUDIO IN ( SAT )
VIDEO SECTION (Page 25) VIDEO SECTION (Page 25)
B C
AV SEL12
IC509 (2/4) SYSTEM CONTROLLER
: TUNER
L R R-CH
81 AV SEL0 82 AV SEL1 83 AV SEL2
HCD-DZ100
26
26
HCD-DZ100
5-4. BLOCK DIAGRAM AUDIO SECTION
· Signal Path
: AUDIO
IC108 STREAM PROCESSOR
IC101 POWER DRIVER
SPEAKER
AMP SECTION (Page 26)
A
D1 D3, SCK, BCKO, LRCKO
D1 SCK BCKO LRCKO
OVF2 SCDT SHIFT LAT1 INIT NSPMUTE SOFTMUTE
R
31 DATA
OUTR1 6
OUTR2 4
IC802 FL DRIVER
14 29 SG1 SG16
IC509 (3/4) SYSTEM CONTROLLER
36 30 29 25 24 21 22 23 27 18 19
R L L
XFSIIN BCK OUTL1 11 LRCK OUTL2 9 FLAGL OVF OVF FLAGR SCDT SCSHIFT XFS0OUT 14 SCLATCH INIT FS0I 38 NSPMUTE SOFTMUTE XFS0IN 48
29 2 PWMBP OUTB 30 17 PWMAP OUTA 25 26 4 RESET
SD
LPF
(+) ()
LPF
FRONT R
13
Q101, 102 DC DETECT
IC102 POWER DRIVER
IC305 OSC
DIN 7 CLK 8 STB 9
27 FL DATA 24 FL CLK 28 FL CS/STB
29 2 PWMBP OUTB 30 17 PWMAP OUTA 25 26 4 RESET
SD
LPF
(+) ()
LPF
FRONT L
X450 49.152MHz
IC109 STREAM PROCESSOR
13
47 31 GR2 GR12
Q103, 104 DC DETECT
GR1
FL801 FLUORESCENT INDICATOR TUBE
J201
30
VFL
XFS0OUT 14
IC103 POWER DRIVER
42
F1 F2
D2 SCK BCK LRCK
KEY0 KEY2 97,95,94
31 DATA
OUTR1 6
SR SR SL SL
G1
Q802 FL DRIVER
S801 S808
74 KEY INT
OVF2 SCDT SHIFT LAT2 INIT NSPMUTE
SOFTMUTE
36 30 29 25 24
XFSIIN BCK LRCK FLAGL OVF OVF FLAGR
OUTR2 4
OUTL1 11
OUTL2 9
29 2 PWMBP OUTB 30 17 PWMAP OUTA 25 26 4 RESET
SD
LPF
(+) ()
LPF
SURR R
13
21 22 23 27 18 19
SCDT SCSHIFT SCLATCH INIT NSPMUTE SOFTMUTE
Q105, 106 DC DETECT
KEY0
FS0I 38
XFS0IN 48
IC104 POWER DRIVER
Xout 13
X502 5MHz
29 2 PWMBP OUTB 30 17 PWMAP OUTA 25 26 4 RESET
SD
LPF
(+) ()
LPF
SURR L
Xin 15
IC110 STREAM PROCESSOR
13
Q107, 108 DC DETECT
IC801 REMOTE CONTROL RECEIVER
4 SIRCSIN
D3 SCK BCKO LRCKO OVF SCDT SHIFT LAT3 INIT NSPMUTE SOFTMUTE OVF2
31 DATA
IC105 POWER DRIVER
OUTR1 6
OUTR2 4
OUTL1 11
C C WF WF
S800 VOLUME ENCODER
10 ENA
11 ENB
VOLUME
DAMP SCDT DAMP SHIFT DAMP LAT1 DAMP LAT2 DAMP LAT3 DAMP INIT DAMP SOFT MUTE OVERFLOW1 OVERFLOW2
1 2 51 52 53 54 55 49 50
SCDT SHIFT LAT1 LAT2 LAT3 INIT SOFTMUTE OVF OVF2
36 30 29 25 21 22 23 27 18 19 24
XFSIIN BCK LRCK FLAGL OVF SCDT SCSHIFT SCLATCH INIT NSPMUTE SOFTMUTE OVF FLAGR
29 2 PWMBP OUTB 30 17 PWMAP OUTA 25 26 4 RESET
SD
LPF
(+)
LPF
CENTER
()
OUTL2 9
13
FS0I 38 FS0CKO 37
Q109, 110 DC DETECT
J202
XFS0IN 48
IC106 POWER DRIVER
29 2 PWMBP OUTB 30 17 PWMAP OUTA 25 26 4 RESET
13
SD
LPF
(+) ()
LPF
Q111, 112 DC DETECT
WOOFER
DRIVE RST 47
FAN
Q301 PROTECT DETECT
DRIVE OCP 48
+12V
FAN
DRIVE
Q302-304
HCD-DZ100
27
27
HCD-DZ100
5-5. BLOCK DIAGRAM POWER SECTION
T901 TRANSFORMER(MAIN)
D901 AC IN
D931
DC/DC CONVERTER T801 F1 F2 TO FLUORESCENT INDICATOR TUBE VFL RECT D801,802 D804,805
+31.5V IC931 VOLTAGE DETECT
D905
Q901 VOLTAGE CONTROLLER
IC901 POWER PROTECTION
+5V
PC901 PHOTO COUPLER
OSC Q801
Q943,947 VOLTAGE DETECT +12V +9V IC515 +9V REG
E4V
PC903 PHOTO COUPLER
T902 TRANSFORMER (SUB) D941 Q921 REG IC921 POWER PROTECTION
IC941 +12V REG
D922 M -8V +5V IC516 +5V REG +5V +3.3V IC105 +3.3V REG +6V RF +3.3V IC107 +3.3V REG +3.3V IC942 +5V REG E 4V IC106 +1.8V REG IC943 +3.3V REG D943 D942 Q945 MOTOR DRIVE CONTROLLER D944
IC509 (4/4) SYSTEM CONTROLLER
P CONT2 44
+1.8V
P CONT1 40
+1.8V IC303 +1.8V REG IC951 VOLTAGE DETECT PC902 PHOTO COUPLER
AC_CUT 20 Q506 RESET 12 IC511 RESET
HCD-DZ100
28
28
HCD-DZ100
5-6. PRINTED WIRING BOARD DMB11 BOARD (SIDE A)
· See page 23 for Circuit Boards Location. :Uses unleaded solder.
1 A
2
3
4
5
6
7
8
9
10
New part of EEP ROM (IC103) on the DMB11 board cannot be used. Therefore, if the mounted DMB11 board (A-1121-906-A, etc.) is replaced, exchange new EEP ROM (IC103) with that used before the replacement.
MAIN BOARD CN503 (Page 36)
C
2
6 7
B
I
I/O BOARD CN201 (Page 47)
1
· Semiconductor Location
Ref. No. D1001 D3501 D3502 IC101 IC102 IC103 IC104 IC106 IC201 Location E-7 B-6 B-6 G-4 E-4 D-6 E-6 E-8 G-7 D-3
C
D
OPTICAL PICK-UP BLOCK (KHM-310CAA/ C2NP)
IC103
Q103
A
IC102 IC104 IC106
MAIN BOARD CN504 (Page 36)
E
B
F
SPINDLE MOTOR SLED MOTOR MAIN BOARD CNP506 (Page 37)
G
IC101
IC201
5 4 2
1 2 1 12 13
H
not used
I
J
MS-203 BOARD CN001 (Page 50)
D
MAIN BOARD CN505 (Page 36)
HCD-DZ100
29
29
HCD-DZ100
5-7. PRINTED WIRING BOARD DMB11 BOARD (SIDE B)
· See page 23 for Circuit Boards Location. :Uses unleaded solder.
1 A
2
3
4
5
6
7
8
9
10
· Semiconductor Location
B
AEP,UK,RU
Ref. No. D3601 D3602 IC105 IC107 IC3601 IC4501 IC4502 Q101 Q102
Location B-3 C-3 F-8 D-7 B-3 D-3 E-3 D-8 E-8
IC3601
C
IC107
D
IC4501
AEP,UK,RU
E
IC4502
F
IC105
G
H
I
HCD-DZ100
30
30
HCD-DZ100
5-8. SCHEMATIC DIAGRAM DMB11 BOARD (1/5)
JL4601 JL4603 JL4605 JL4607 JL4609 CN401 5P
JL4602 JL4604 JL4606 JL4608 JL4610
FB402 0UH
FL401 0UH
FB404 0UH FB403 0UH C402 47 16V FL402 EMI FL403 0UH C403 47 6.3V FB406 0UH
FB401 0UH
FB405 0UH
CN301 13P R308 100 JL4701
JL4703 R4701 0 JL4704 JL4705 R4702 0 R4703 0 R4704 0 R4705 0 R4706 0 JL4706 JL4707 JL4708 JL4709 JL4710 JL4711 JL4712 JL4713
FL4501 0UH
C4501 10 10V F
C4502 0.01 25V B
IC4501 SN74LVC541APWR
CN4501 11P JL4501 JL4502 R4514 0 R4515 0 R4516 0 R4510 47 JL4503 JL4504 JL4505 JL4506 JL4507 JL4508 JL4509 JL4510 JL4511
R4502 0 R4518 0 R4501 0
R4511 100 R4512 0UH R4513 0 C4504 0.01 25V B
R4520 0
IC4502 SN74LVC1G125DCKR
HCD-DZ100
31
31
HCD-DZ100
5-9. SCHEMATIC DIAGRAM DMB11 BOARD (2/5)
· See page 51 for Waveforms. · See page 58 for IC Pin Function Description.
R143 100
JL103
JL104
JL105
JL106
R1531 0
R151 47
R155 47
R153 47
R160 47
R1530 0
R1120 0UH R1527 0 R1102 150 R197 150 R195 150 R1121 0UH R1122 0UH
C151 0.001 25V CH ICT128 R138 100k C130 0.1 16V B R136 15k C132 0.1 16V B C139 22p 50V CH C140 0.1 16V B C146 0.1 16V B C149 0.1 16V B
C152 C153 12p 12p 50V 50V CH CH
X101 27MHz
R1542 0
R1168 470 R1103 10k ICT133 25V B
16V B
50V B
R192 150 R190 150 R189 150
R1123 0UH R1124 0UH R1125 0UH
R1547 4.7k
C147 0.047 16V B
C148 0.047 16V B
C150 10 16V
C138 0.001
R144 0
C135 0.033
R1551 4.7k
R1548 4.7k
R1549 4.7k
R1550 4.7k
R1104 10k
C137 0.1
C154 0.1
R126 0 C195 0.22 16V B
C163 0.01
JL166
JL165
CL103
JL129
JL128
JL160
C133 0.1 16V B
R141 750k
R142 100k
R1540 4.7k
16V B
CL1504
JL1502
JL1501
CL1503
CL1502
16V B
R1543 10k
ICT136
FL101 0UH
ICT129
IC107 TK11133CSC L-G C192 0.01 25V B
C193 0.22 16V B
C156 0.01 25V B
C159 0.01 25V B
CN101 24P JL139 JL140
C101 0.01 25V B
C120 1 10V B C121 1 10V B C122 1 10V B C123 1 10V B
C161 0.01 25V B R1553 0 R1101 2.2k
JL141 JL142 JL143 JL144 CL112
C124 1 10V B JL101
C170 0.01 25V B C171 0.01 25V B C172 0.01 25V B
JL145 JL146 JL147 JL148 JL149
JL130 JL167 CL113 JL102 JL127 JL132
CL114 CL115 CL116
/ C2NP
JL150 JL151 JL152 JL153 JL154 JL155 JL156 JL157 JL158 JL159
JL133 ICT109
CL117 CL118
0.1
C116 16V B
R1108 0 R1105 10k ICT1501 ICT138 R1111 0 0.1 C114 16V B C125 0.1 16V B CL101 C173 0.01 25V B
R1555 4.7k
0.1
C115 16V B C118 10 16V
C117 10 16V
JL135
CL104
R116 1k
C119 10 16V R101 100 Q101 UM6K1N-TN C126 0.1 16V B R117 47k CL108 CL109 CL110 IC102 CXD9849R
C196 0.0047 CL105
C174 0.01
25V B JL161 JL162
RB104 0 1/32W
C175 0.01 ICT127 R108 1M R111 100 Q103 RT1N241C-TP-1 JL136 R1554 4.7k
25V B
RB103 0 1/32W
R1109 0 ICT134
R120 22 R113 22
RB111 0 1/32W
ICT121 ICT126 ICT123 C105 47 6.3V ICT124
R121 22
R115 22
R112 22
R118 22
C112 47 6.3V
R124 47k CL1501
C127 0.01 25V B
C176 0.01
25V B
R110 47k CL106 CL107 R107 10k C106 0.01 25V B R109 0
ICT125 R123 0 Q102 QST8TR C128 0.0015 50V B JL163 RB108 22 1/32W
R114 100k
R1129 100k
C113 0.01 25V B
ICT114 ICT115
ICT112
R196 0
ICT116 ICT117 ICT118
FL105 0UH
RB107 22 1/32W
C129 10 16V
C162 0.01 25V B
JL168
JL169
JL172
JL170
JL137
JL171
JL173
C155 0.01 25V B
C131 2.2 6.3V B C136 0.01 25V B C144 0.01 25V B
C158 0.01 25V B
C164 0.01 25V B
C177 47 6.3V
FL106 0UH
R1557 100
R161 100
ICT113
C160 0.01 25V B
R152 0
RB112 22 1/32W R1504 0UH
RB113 22 1/32W
R164 100
HCD-DZ100
32
32
JL164
HCD-DZ100
Ver. 1.2 5-10. SCHEMATIC DIAGRAM DMB11 BOARD (3/5)
New part of EEP ROM (IC103) on the DMB11 board cannot be used.
Therefore, if the mounted DMB11 board (A-1121-906-A, etc.) is replaced, exchange new EEP ROM (IC103) with that used before the replacement.
C181 0.1 16V B
IC104 HY57V64162 0HGTP-HDR
RB106 47 1/32W
C180 0.1 16V B
RB105 47 1/32W
MR27V3202J-0L7TN
: US
C179 16V B
0.1
MX29LV320ABTC65-0BA2-0503GA
: KR
C191 16V B ICT108 C190 47 6.3V FL108 0UH
0.1
C102 1 6.3V R169 10k
C184 0.01 25V B ICT110
R187 0
IC101
C182 0.22 16V B
IC105 TK11133CSC L-G
R104 0
R1133 0 R105 10k R106 10k FL104 0UH
C188 0.22 16V B
ICT111
ICT104
ICT102
ICT106
D1001 RB501V -40TE-17 IC106 PQ018EN01ZPH R1134 0 C178 47 4V FL107 0UH C189 0.33 10V B C187 47 4V
IC103 BR24L64F-W E2
ICT103
ICT105
ICT101
R193 1k
R1545 XX
C167 0.01 25V B
JL138 JL114 JL115 JL116 JL117 JL118 JL119 JL120 JL121 JL122 R1502 0 FB115 0UH C108 0.001 50V B C109 0.001 50V B FB111 0UH FB112 0UH FB113 0UH ICT137 R1546 3.3k R1150 3.3k
R191 1k
ICT107
JL107 JL108 JL109
FB114 0UH R1152 3.3k R1151 3.3k R1110 2.7k
JL110 JL111 JL112 CN105 6P
CN106 11P
HCD-DZ100
33
33
HCD-DZ100
5-11. SCHEMATIC DIAGRAM DMB11 BOARD (4/5)
· See page 52 for IC Block Diagram.
R3611 100
C3610 0.1 IC3601 PCM1803DBR
16V B
R3621 100
C3609 10 16V C3611 0.01 25V B C3621 0.01 25V B
C3608 10 16V
L3601 R3605 0
C3607 0.1 16V B
L3602 C3605 47 6.3V
C3606 0.1
16V B
R3601 100
C3602 0.1 16V B
R3607 0
C3603 0.1 16V B R3603 10k
R3606 0
C3601 10 10V F
R3602 100 D3601 1SS355TE-17 CN302 7P JL3516 D3602 1SS355TE-17 JL3517 JL3518 JL3519 JL3520 JL3521
R3609 0
D3501 1SS355TE-17
D3502 1SS355TE-17
HCD-DZ100
34
34
HCD-DZ100
5-12. SCHEMATIC DIAGRAM DMB11 BOARD (5/5)
R223 100k
R225 100k
R234 10k C212 0.01 25V R230 82k B C214 0.001 50V B R232 18k
R231 15k
C233 0.0047
R220 10k
R226 56k
CL207
R233 33k CL206
CL208
C209 0.033 16V B
R221 56k
C211 0.033 16V B
CL209 C215 0.01 25V B
R212 10k
R208 33k C205 220p 50V CH R206 10k R209 33k C206 220p 50V CH R215 12k CL202 R214 15k CL201
CL210 JL201 CL211 CL212 JL202 JL203 JL204 JL205 JL206
CN201 6P
C218 10 16V
C219 0.01 25V B
C220 10 16V
C224 0.01 25V B
R246 4.7k
R247 1k
R207 2.7k R204 1.2k
C203 0.01 25V B CL203
0.1
C221 16V B R236 1k R2505 0
C225 0.001 JL207 JL208 R237 1k JL209 C226 0.001 R243 100 JL210 JL211 ICT203 ICT204
CN202 5P
R205 10k R210 47k C208 0.01 25V B R216 12k CL204 IC201 FAN8036L R213 6.8k C223 0.1 ICT206
C222 0.1 16V B
ICT205 R238 4.7k R239 4.7k
CL205
R227 0
R228 0
R219 27k
R224 10k C210 0.01 25V B
C213 0.01 25V B ICT207
C217 47 16V
R222 33k
HCD-DZ100
35
35
HCD-DZ100
5-13. PRINTED WIRING BOARD MAIN BOARD (SIDE A)
· See page 23 for Circuit Boards Location. :Uses unleaded solder.
1 A
2
3
4
5
6
7
8
9
· Semiconductor Location
B
C110
Ref. No. D503 D914 D915 D923 D925 D932 IC101 IC102 IC103 IC104 IC105 IC106 IC108 IC109 IC110 IC303 IC305 IC503 IC509 IC511 Q506 Q507 Q943 Q947
Location H-4 F-8 F-8 H-8 H-8 D-7 D-5 D-5 D-4 D-4 D-3 D-2 E-5 E-4 E-3 D-6 E-5 E-2 H-3 H-4 H-4 G-3 D-7 D-7
C
D
IC106 IC105 IC104 IC103 IC102 IC101 IC303
3 4
C119
E
E
1 5
E
A
DMB11 BOARD CN4501 (Page 29)
IC503
R501
IC110
IC109
IC108
IC305
F
I/O BOARD CN601 (Page 47)
6
G
C
DMB11 BOARD CN302 (Page 29) E
CN503
F
2
1
R716
7
D
DMB11 BOARD CN106 (Page 29)
2
CN505
H
10
11
EXCEPT SP
1
R639
EXCEPT AEP,UK
IC509
R593
R592
4 5 E
3 1
IC511
22
R656
for PROGRAM WRITER
HCD-DZ100
36
36
HCD-DZ100
Ver. 1.2 5-14. PRINTED WIRING BOARD MAIN BOARD (SIDE B)
· See page 23 for Circuit Boards Location. :Uses unleaded solder.
1 A
2
3
4
5
6
SPEAKER
7
8
9
· Semiconductor Location
Ref. No. Location D-4 D-5 D-5 D-6 D-7 D-7 D-5 D-5 D-6 D-7 D-7 D-8 B-9 B-9 H-7 H-6 H-6 D-2 G-2 G-2 G-1 G-2 D-3 H-2 G-2 H-3 H-2 H-2 H-2 G-4 H-4 H-4 H-4 H-4 H-5 H-5 H-5 F-1 H-2 E-4 G-5 G-5 G-4 H-4 E-3 H-3 D-3 B-4 B-5 B-5 B-5 B-6 B-6 B-6 B-6 B-7 B-7 B-8 B-8 C-9 B-4 B-4 B-4 G-2 H-2 H-5 D101 D102 D103 D104 D105 D106 D201 D202 D203 D204 D205 D206 D303 D304 D504 D505 D506 D901 D905 D906 D907 D908 D909 D910 D913 D921 D922 D924 D926 D931 D941 D942 D943 D944 D945 IC515 IC516 IC901 IC921 IC931 IC941 IC942 IC943 IC951 PC901 PC902 PC903 Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q301 Q302 Q303 Q304 Q901 Q921 Q945
FRONT R
FRONT L
SURR R
SURR L
CENTER
WOOFER
US,CND,MX
+
+
AC IN FAN
(CHASSIS)
B
EXCEPT US,CND,MX
R930 R924
1 E E
2 E E E
C108
E
EXCEPT US,CND,MX L107
+
+
E
E
E
E
E
+
E
E
+
E
E
C109
R901
EXCEPT US,CND,MX
65 C9
E
C
C966 EXCEPT US,CND,MX
R479
R478
R468
D
PC903
3 1
IC931
E
PC901
C120 C502
C501 R503
AEP,UK
MAIN TRANSFORMER
US,CND,MX
R710
R536 R535
R712
IC901
2
US EXCEPTUS, KR
4
5
G
E
R921
R929
SUB TRANSFORMER
R523
IC943
IC942
IC941
R714
1
R715
R711
F
R744
R742
1
5
1
5
1
5
H
8
R733
IC921
1
R719
IC516
E E 1 3
R734
EXCEPT AEP,UK
R720
PC902
3
R732
IC951
1 3 1 5
19 18
1 2
1
IC515
B
DMB11 BOARD CN401 (Page 29)
22
E
FL BOARD CN801 (Page 45)
HCD-DZ100
37
37
R469
HCD-DZ100
Ver. 1.2 5-15. SCHEMATIC DIAGRAM MAIN BOARD (1/7) · See page 51 for Waveform. · See page 55 for IC Pin Function Description.
46
CN509 19P FFC-S-1.0
TP624
TP594
TP632
TP625
TP593
TP603
TP600
TP598
TP599
TP630
TP631
C608 100p
R706 100
R707 100
R601 100
R628 1k
R608 100
R710 0 R711 100 R712 0 R714 0 R715 0 R716 100
R620 100
TP596
TP597
TP560
TP595
TP601
TP570
EXCEPT AEP,UK RDS-CLK RDS-DATA
R733 10k
R523 10k
40 AEP,UK
TP548 TP547 TP546 TP545 TP578 TP576 TP592 TP591 TP590 TP589 TP588 TP587 TP586 R595 100 R591 100 R594 100 R590 100 R589 1k R588 100 R587 100 R586 100 R585 100 R536 1K R535 1K
R718 10k
R721 10k
RDS-DATA RDS-CLK
TP513
R732 10k
R734 10k
R742 10k
R744 10k R756 1k
C856 0.1
Q507 RT1P141C -TP-1
C762 0.1
* R792
1.5K: RU 4.7K: AEP,UK 10K: MX,E32 22K: US,CND 47K: EA,AUS no mount: SP
R750 1k R749 R748 1k 1k
R774 1k
I/O (1/2)
R746
47k R611 10k
TP585 TP584 TP583
CE
TP550
39
48
TP582 TP581 TP580
R702 10k
R596
R792
R741 TP502 TP792 IC509 M30620MCP-A01FPU0:EXCEPT US M30620MCP-A15FPU0:US
47k
*
TP577 R577 6.8K
*
TP793 R789 100 TP514 TP515 R790 100 TP512
OCSW
C572 CN507 23P FFC-S-1.0 C571
0.1 0.1
R616 10k R614 10k R791 100
C570 0.1 EB905 TERMINAL BOARD GROUND
TP817 R612 10k C799 0.1 C798 0.1 TP501 R639 100
V-CONTROL
* R596 1K: SP 10K: EA 15K: AUS 47K: US,CND,RU, MX,E32 no mount: AEP,UK
C716 0.1
R726 1k
R728 1k
R713 0
V-CONTROL
4
TP507
TP508
R729 4.7k
R717 10k
R730 4.7k
R763 100
R762 100
R761 100
R760 100
R764 100
R765 100
R592 10k
R593 10k
X502 5MHz
0.1
C875 0.01
R514 1k
C580 1000 6.3V
TP500 TP503
TP504
TP505
R719 10k
TP506
R705 10k
R720 10k
R709 10k
TP509
TP510
TP511
R727 4.7k
R725 4.7k
C712
R775 47k
CN510 9P FFC-S-1.0
CN503 7P
DMB11 BOARD (4/5) CN302 (Page 34)
39
HCD-DZ100
38
38
HCD-DZ100
5-16. SCHEMATIC DIAGRAM MAIN BOARD (2/7)
38
IC515 TA7809LS
TP517 C595 0.1 C596 47 35V C597 0.33 R704 1k R703 1k
C603 100 10V
IC516 TA7805LS TP518
C525 0.1
46
C602 0.1 C601 47 35V C598 0.33
D506 1SS355TE-17
D505 1SS355TE-17
TP538
38
D503 1SS355TE-17
R609 0
TP542
OCSW
R607 680
C548 0
R606 680
R657 47k
C547 R615 47p 470
R656 0
R636 0
IC503 SN74AHC2G157 HDCU3
R694 100
R695 100
R697 100
R701 100
R692 100
R693 100
R696 100
C501 0.1
R629 0
R637 0
R638 100
Q506 2SC2412K-T-146-QR C582 100 10V R662 47k
C583 0.22 10V
R673 10k
IC511 PST3629NR
R678 0
C502 0.1
R501 100 R722 47k
D504 1SS355TE-17
R503 100
R659 100k
C587 0.22 10V
C589 0.1
R739 47k
TP553
TP554
TP564
TP552
TP562
TP563
TP574
TP555
TP566
TP569
TP556
TP573
TP557
TP558
TP572
TP559
TP565
TP568
TP575
TP571
TP567
TP561
TP551
TP829 TP830 TP831 TP832
CNP506 5P PIN-S-2.0 BOARD IN
CN505 11P FFC-S-1.0
CN504 11P FFC-S-1.0
DMB11 BOARD (1/5) CN401 (Page 31)
DMB11 BOARD (3/5) CN106 (Page 33)
DMB11 BOARD (1/5) CN4501 (Page 31) 40
HCD-DZ100
39
39
HCD-DZ100
5-17. SCHEMATIC DIAGRAM MAIN BOARD (3/7) · See page 53 for IC Block Diagrams.
R345
10k
R347
10k
25V F
C326 0.1
R468 0
R469 0
TP331 R317 470
R316 470
R319 10k EB907 TERMINAL BOARD EB910 TERMINAL BOARD R353 100
TP334
C325 0.1
25V F
C324 0.1
25V F
R382 560
R381 560
R380 560 IC110 CXD9843AR C327 0.1 R326 0 C328 0.1 25V F 25V F R379 560 C323 0.1 25V F
C120 47/10V
D-GND
R356 470 TP305 R309 100 R308 100 R306 100 R305 100 R304 100 R303 100 R328 0 C335 47 16V
39
R302 100 R351 100 R300 100 C320 0.1 25V F
C321 0.1 25V F
C322 0.1 25V F R329 0
C403 100p 50V CH
C404 100p 50V CH
C405 0.001 50V B
C402 50V CH
41
100p
25V F C317 0.1
R318 470 R344 470 TP329 TP333
TP368 R310 100 R311 100 R312 100 R313 0 R314 100 R315 0
C406 0.0047 50V B
38
C316 0.1
25V F
R378 560 C315 0.1 25V F
R377 560 R354 100 R376 560 IC109 CXD9843AR C314 0.1 25V F
C318 0.1
25V F
R327 0 C319 0.1 25V F
R375 560
R357 470 TP335
43
C332 47 16V
R324 0
42
HCD-DZ100
40
40
C313
0.1
C311 0.1 25V F
C312 0.1 25V F
25V F
HCD-DZ100
5-18. SCHEMATIC DIAGRAM MAIN BOARD (4/7) · See page 53 for IC Block Diagrams.
IC106 CXD9774M
C116 1 16V F C372 1 50V
R119 22k
R176 0
C186 0.033 50V B
R431 100k
0.1
C200 25V F
R166 0 C146 0.1 25V F
C272 0.22 50V
C176 0.22 50V
R206 3.3
D303 1SS355TE-17 C377 10 50V
C136 0.1 25V
R246 100
R156 0
R146 R136 0
0
C271 0.22 50V
C166 0.22 50V
R196 3.3 L136 TP389
R430 10k
C156 0.033 50V B
D206 P6SMB39AT3
C292 0.0022 50V C226 1 50V C266 0.0022 50V R226 2.7
R118 22k C106 1 16V F C196 2200 35V
R216 2.7
D106 P6SMB39AT3
IC105 CXD9774M
C115 1 16V F
C216 1 50V
C256 0.0022 50V
40
R117 22k C185 0.033 50V B
L126
C291 0.0022 50V
D304 1SS355TE-17
44
R175 0 C199 25V F R165 0 C145 0.1 25V F
0.1
C210 0.22 50V
C175 0.22 50V
R205 3.3
L135
R145
0
R135 0
C209 0.22 50V
C165 0.22 50V
D205 P6SMB39AT3
C135 0.1 25V
R245 100
R155 0 C290 0.0022 50V C265 0.0022 50V R225 2.7 C155 0.033 50V B TP388
R195 3.3
C225 1 50V
EB908 TERMINAL BOARD
R481 10k
R450 10k
R482 10k
R451 10k
R483 10k
R452 10k
R484 10k
R453 10k
R116 22k
C195 2200 35V C105 1 16V F
D105 P6SMB39AT3
R215 2.7 C215 1 50V
C280 0.01 50V
C279 0.01 50V
C255 0.0022 50V C289 0.0022 50V
L116 L106 L115 L105
TP372 TP373 TP374 TP375
IC104 CXD9774M
C114 1 16V F
L125
Q301 2SC3052EF-T1-LEF R139 0 R409 100k R365 100k R410 100k
R115 22k
R411 100k
C184 0.033 50V B R174 0 C198 25V F R164 0 C144 0.1 25V F C208 0.22 50V C174 0.22 50V R204 3.3 L134
R395 100k
C385 2.2 16V F
R366 100k
R412 100k
C268 0.01 50V
C269 0.01 50V J202 TERMINAL BOARD
0.1
C395 2.2 16V
C396 10 10V
D204 P6SMB39AT3
C288 0.0022 50V C224 1 50V C264 0.0022 50V R224 2.7
Q110 2SA1235TP-1EF
Q112 2SA1235TP-1EF
C134 0.1 25V
R244 100
R154 0
R144
0
R134 0
C207 0.22 50V
C164 0.22 50V
R194 3.3
Q109 2SA1235TP-1EF
Q111 2SA1235TP-1EF
R214 2.7
D104 P6SMB39AT3
C154 0.033 50V B
TP387
C214 1 50V
C254 0.0022 50V C287 0.0022 50V
R114 22k
C194 2200 35V C104 1 16V F
L124
42
43
HCD-DZ100
41
41
HCD-DZ100
5-19. SCHEMATIC DIAGRAM MAIN BOARD (5/7) · See page 51 for Waveform. · See page 53 for IC Block Diagram.
40
L107 10uH CN300 2P C307 100 16V C108 0.1
Q303 2SC3243TP-E
R428 2.2k
R424 1.5k
R426 10k
41
R325 0
Q302 2SC3052EF-T1-LEF
R429 1.2k
C308
TP330 R348 470
TP341
R427
10k
C306
0.1
0.1
C109 0.1
C248 47 16V
25V
25V
Q304 2SC3052EF-T1-LEF
R346 470
F
F
R322 10k
R374 TP332 C305
560 0.1
1/10W 25V F
R373 R355 100 TP336
IC108 CXD9843AR
560
R372 C304
560 0.1 25V F
C309 R323
0.1 0
25V F R371 560
5
C310 R358 0.1 470 TP337 C329 47 16V 25V F
43
0.1
0.1
0.1
R320
0
25V
25V
25V
R321 0
F
F
F
C302
C301
C303
TP325
R393 22
L303 0
TP392
TP364
FB301 0UH
L301
C382 0.001 50V
C383 10p 50V L302
TP327
TP363
TP396
IC305 SN74AHC1GU04DCKR
TP362 C368 1 10V R400 100k
IC303 TK11118CSCL-G C375 100 16V C374 25V
C380 220 10V B
C381 0.01 25V B
R396 100 R394 1M
0.01
X450 49.152MHz
44
C384 5p 50V C371 0.001 50V B
HCD-DZ100
42
42
HCD-DZ100
5-20. SCHEMATIC DIAGRAM MAIN BOARD (6/7) · See page 53 for IC Block Diagrams.
41
IC103 CXD9774M C113 1 16V C110 0.001 R113 22k L133 C183 0.033 50V C286 0.0022 50V
Q106 2SA1235TP-1EF
Q108 2SA1235TP-1EF
R173 0 C190 0.1 25V R163 0 C143 0.1 25V
D203 P6SMB39AT3
C297 0.01
C298 0.01
C299 0.01
C296 0.01
C206 0.22 50V
C173 0.22 50V
R203 3.3
C223 1 50V
C263 0.0022 50V R223 2.7
Q105 2SA1235TP-1EF
R363 100k
Q107 2SA1235TP-1EF
R364 100k R408 100k
50V
50V
50V
50V
C393 2.2 16V
C394 2.2 16V F
J201 TERMINAL BOARD TP379
R405 100k
R406 100k
R407 100k
R461 10k
R491 10k
R460 10k
40
R143
0
D103 P6SMB39AT3
R133 0
C205 0.22 50V
C163 0.22 50V
R193 3.3
R213 2.7 C213 1 50V C253 0.0022 50V C285 0.0022 50V
R492 10k
R493 10k
R462 10k
C133 0.1 25V
R243 100
R153 0 TP378
L114
TP377
TP386 C153 0.033 50V
L104 L113 L103
TP376
R456 10k
R487 10k
R457 10k
R488 10k
R489 10k
R458 10k
R490 10k
R459 10k
L123 R112 22k C103 1 16V F
R463 10k
TP383 R464 10k TP382
C193 2200 35V Q102 2SA1235TP-1EF
Q104 2SA1235TP-1EF
L112 L102
TP381
50V
50V
L101
50V
R111 22k L132 C182 0.033 50V Q101 2SA1235TP-1EF
C391 2.2 16V R361 100k Q103 2SA1235TP-1EF
C392 2.2 16V R362 100k
R172 0 C189 0.1 25V R162 0 C142 0.1 25V
D202 P6SMB39AT3
C284 0.0022 50V C222 1 50V C262 0.0022 50V R401 100k
C204 0.22 50V R152 0
C172 0.22 50V
R202 3.3
R402 100k
R403 100k
R404 100k EB906 TERMINAL BOARD
R142
0
R132 0
R192 3.3
D102 P6SMB39AT3
C132 0.1 25V F
R242 100
R222 2.7
C203 0.22 50V
C162 0.22 50V
C212 1 50V
R212 2.7 C252 0.0022 50V C283 0.0022 50V
TP385 C152 0.033 50V L122 C192 2200 35V C102 1 16V F
42
R110 22k
C111 1 16V
IC101 CXD9774M
R109 22k L131 C181 0.033 50V B
R171 0 C188 25V F R161 0 C141 0.1 25V
0.1
D201 P6SMB39AT3
C202 0.22 50V R151 0
C171 0.22 50V
R201 3.3
C221 1 50V
C282 0.0022 50V C261 0.0022 50V R221 2.7
R141
0
D101 P6SMB39AT3
C131 0.1 25V F
R241 100
R131 0
C201 0.22 50V
C161 0.22 50V
R191 3.3
C211 1 50V
R211 2.7 C251 0.0022 50V C281 0.0022 50V
TP384 C151 0.033 50V
L121
R108 22k C191 2200 35V C119 100P
R478 0
R479 0
R473 0
R474 0
R472
R475 0
C101 1 16V F
C275 0.01
C278 0.01
C277 0.01
C276 0.01
50V
C112 1 16V F
IC102 CXD9774M
L111
TP380
44
C366 220 16V
C367 0.1 25V
C350 0.1 50V
EP909 PLATE GROUND EB911 TERMINAL BOARD
HCD-DZ100
43
43
HCD-DZ100
Ver. 1.2 5-21. SCHEMATIC DIAGRAM MAIN BOARD (7/7)
EXCEPT US,CND,MX
R930 0
* C938
330P / 250V: US,CND,MX 680P / 250V: EXCEPT US,CND,MX
* C931
47000P / 630V: CND,MX 10000P / 630V: EXCEPT US,CND,MX,KR no mount : US,KR
F901 T6.3AL / 250V : EXCEPT US,CND,MX,E32 T8AL / 250V: E32 T8AL / 125V : US,CND,MX CN901 2P TP901 TP902 FH901 HOLDER FUSE F901 FH902 HOLDER FUSE
*
EXCEPT US,CND,MX
41
R924 0
* C903 / 200V: US,CND 1000
C966 220P 250V R901 1M
C938
C965 220P
C963
*
JW904 C902 0.22 275V
1000 / 250V: MX 330 / 400V: AEP,UK,KR 330 / 450V: RU,EA,SP,E32,AUS TH901 D901 D5SBA60F01
*
D931 YG906C2R C931 L931 10.8uH
43
* C905
0.01 / 400V: US,CND,MX 0.0015 / 400V: EXCEPT US,CND,MX
T901 MAIN TRANSFORMER
*
TP903 TP904
C901 0.22 275V
C964
50V
C932 2200 35V C933 2200 35V
US,CND, MX
R902 3.3M
EXCEPT US,CND,MX
*
LF901
C937 0.047 50V C905 R903 R904
R933 4.7k R932 33k 0.5% R965 0
C934 2200 35V
*
VDR901 VARISTOR
C920 0.01
R931 4.7k 0.5%
TP905 R937 10k R940 10k TP906
42
* * C963,C964
JW903 C918 0.01 250V C903 680P / 250V: US,CND,MX 0.001 / 250V: EXCEPT US,CND,MX
*
*
US FB902 0.45UH
3300P / 1.2KV: US 0.0015 / 500V: CND,MX 1000P / 1.5KV: EXCEPT US,CND,MX
*
D913 SARS03
C935 0.1
* C906
R934 3 1k 1 2
R936 470k IC931 TA76431AS (TE12L)
R939 3.3k 0.5%
C936 0.1 50V
C939 0.1 50V
Q943 RT1N441C-TP-1
D932 UDZSTE-175.1B
EB901 Q901 2SB1116A TP-LK D908 1SS355TE-17 R918 0 D906 1SS355TE-17
D905 D1NL20U-TR2
R905 10 R938 1k R910 2.2k
C906
*
C908 47 35V
C911 0.0047 50V
* R903,R904
33K: US,CND,MX 100K: EXCEPT US,CND,MX
R949 1k
Q947 RT1N441C-TP-1
R906 3.3k C907 D907 1SS355TE-17
EB903 R909 100k C910 PC901 TLP421F
C909 220p 50V IC901
*
* IC901
*
R914
STR-F6138-LF1352: US,CND,MX STR-F6168-LF1352: EXCEPT US,CND,MX
*
R913 0.22
R912
R911 220
*
R907 10k
R919 18k
D914 1SS355TE-17
R935 1k
*
D915 UDZSTE-1710B
US,CND,MX C912 EB902
R908 3.3k 1/2W D909
* C910
10: US,CND,MX 22: EXCEPT US,CND,MX,E32 47: E32 PC903 TLP421F
* C907
0.0015: US,CND,MX 0.001: EXCEPT US,CND,MX
* * C912
C913 100p 250V
* R914
0.05: US,CND,MX 0.1: EXCEPT US,CND,MX
* R912
1SS335TE-17
0.22: US,CND,MX 0.33: EXCEPT US,CND,MX
TP907 TP908 TP910 PC902 TLP421F R956 1k R946 150 R943 0 R941 0 TP909
0.0022 / 250V: US,CND,MX 100P / 250V: EXCEPT US,CND,MX
L945
D910 1SS355TE-17 IC921 STR-V153
R925 10 R929 2.2 T902 SUB TRANSFORMER
L942
R948 10k
IC943 SI-3033KM-TL
IC942 SI-3050KM-TL
C947 100 10V
IC941 SI-3120KM-TL
D945 UDZSTE-1720B
39
C951 0.1 25V C942 220 25V TP913 TP912 TP914 C943 100 16V
C953 0.001 2kV C948 470 10V
C955 0.1 25V
C949 100 10V
R920 1K R921 100k 2W
D921 ERA22-08TP3
C945 470 16V
C954 0.1 25V
C921 3300p 500V
0.1 25V
D944 EK19LF-F7
C960 0.1 25V
D941 D1NL20U-TR2
D926 UDZSTE-1724B
L948
TP915 TP916
C967 0.1 25V
C941 1000 25V
D925 UDZSTE-175.1B
C968
D942 RK36LF-B3
L947 R951 220 0.5% R952 2.2k 0.5% Q945 RSR025N0