Braun Espresso master_3061.pdf part of Braun Braun Espresso Master Braun Espresso master_3061.pdf, Braun Espresso Master

Text preview for : Braun Espresso master_3061.pdf part of Braun Braun Espresso Master Braun Espresso Master - Service Manual

Back to : Braun Espresso master_306 | Home

Service Documentation Braun Espresso master

Market Release 10/91

E 200

3061

3061

BINC Rev: 7/96 BAG Rev: 10/91

Service Documentation
Exploded Drawing 3061

3061 - 2

BINC Rev: 1/00 BAG Rev: 2/92

Service Documentation
Spare Parts List 3061 Part Description
Filter insert Filter holder with handle, black Filter holder with handle, white Flap black Flap white 2-Cups adapter, black 2-Cups adapter, white Control knob, black Control knob, white Cover bush, black Cover bush, white Spring ring Control valve with steam pipe Copper washer Cover, black Cover, white Over pressure valve cpl. Screw Sealing Boiler cpl. Holder Screw Seal ring Shower head cpl. Screw Sealing Filter Screw Bayonet catch Screw Mains lead Housing upper part, black Housing upper part white Intermediate part black Intermediate part, white Housing lower part, black Housing lower part, white Drip pan Collecting vessel, black Collecting vessel, white Switch

Pos. No.
1 2 2 3 3 4 4 5 5 6 6 7 8 9 10 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 26 27 27 28 28 29 30 30 31

Part Number
3061630 3062622 3062626 3062612 3062627 3061638 3061666 3061008 3061668 3061009 3061660 3061629 3061628 3061651 3061626 3061617 3061625 3061680 3061640 NLA 3061658 3061684 3061656 NLA 3061631 3061657 3061650 3061682 3061649 3061663 3061645 3061637 3061665 3061006 NLA 3061635 3061663 3061631 3061644 3061669 3061632

3061 - 3

BINC Rev: 1/00 BAG Rev: 10/92

Service Documentation
Spare Parts List 3061 Part Description
Base plate, black Base plate, white Rubber foot Screw Carafe lid, black Carafe lid, white Carafe, black Carafe, white Creaming turbine Over pressure sealing Wire, switch/thermostat Wire, boiler/thermostat

Pos. No.
32 32 33 34 36 35 36 36 37 38

Part Number
3061622 3061619 3061641 0031128 3061636 3061664 NLA 3061752 3061826 3062611 3061671 3061672

3061 - 4

BINC Rev: 7/96 BAG Rev: 7/91

Service Documentation
Service Information 3061

Technical Data Voltage: Nominal wattage (rating): Boiler-Capacity: Collecting vessel-capacity: Steam pressure into boiler: Steam pressure into outlet: Working time for 1 coffee: Working time for following coffees: Water temperature onto the coffee granules: Coffee temperature after brewing process 240 ml: Temperature control: Overheat protection (not exchangeable): Length of mains lead approx. General note Before a repair is made, the switch should be into position "off" while turning Control knob to position "minimum". The plug has to be pulled from the outlet and all attachments removed from the appliance. Note for Screws (34) The special Screws. which are located in the base plate (32), can only be removed with a screwdriver furnished with a special blade insert. This special blade insert for screwdriver can only be ordered from the parts department. Because of approval board requirements and reasons of safety, only this special screw must be used to avoid tampering by unauthorized persons. 120 V 800 Watts + 10% 240 ml approx. 100 ml 2.5 bar - 3 bar approx. 0 bar < 3 Minutes < 30 Seconds 95 °C - 110 °C 83 °C + 3 °C 1 Thermostat 135 °C 2 one way fuses 228 °C 1.10 Meter

3061 - 5

BINC Rev: 7/96 BAG Rev: 7/91

Service Documentation
Service Information 3061

Disasssembly 1. Cover (10) / Over-pressure valve (11) : Remove four screws (12) only. 2. Control knob (5)/ Spring ring (7)/ Cover bush (6): Pull off Control knob from Control valve with steam pipe (8). Then turn Cover bush in counter clockwise direction and also remove by pulling-off from Control valve (8). 3. Bayonet catch (23)/Filter (21)/Sealing (20): Remove four Screws (24) from Bayonet catch, however only one screw has to be removed from the Filter and the Sealing. 4. Base plate (32)/Mains lead (25)/Switch (31): Remove three Screws (34) in the Base plate and take Base plate from Housing lower part (28). 5. Control valve with steam valve (8) : Remove Control Knob (5) and Cover bush (6). Take a 12 mm wrench (open end type) and remove the Control valve from boiler by turning wrench into counter-clockwise direction. 6. Boiler cpl. (14)/shower head cpl. (18)/ Housing upper part (26)/ Housing lower part (28)/ Intermediate part (27): Remove Control valve (8) and three screws (16) located the Housing upper part. Lift Upper housing on the rear side and slide a small distance towards the front, then lift up and remove. After removing the two screws (19), the Shower head and the intermediate part can be separated from the boiler. After the connecting wires have been disconnected from the Switch (31) and the four Screws (16) have been removed from the Holder (15), the Boiler cpl. can be pulled from the Housing lower part in an upward direction. 7. Seal ring (17) / Sealing (13/20) / Copper washer (9): In order to replace these parts, the corresponding subassembly has to be disassembled. This has to be performed with utmost caution. 8. Overheating protection: These parts must not be exchanged when defective. Assembly In general, the assembly follows the above mentioned procedure in reverse. The sealing parts, the Seal ring and the Copper washer have to be assembled very carefully. The assembled product must not indicate a leakage in any place. The wiring has to be checked prior the assembly of the base plate. The connecting wires must not be damaged or pinched. For a proper strain relief, the Mains lead has to be installed between the ribs provided for. After each repair, the brewing function should be checked as well as proper steaming.

3061 - 6