Text preview for : 4714.pdf part of Braun Oral Line Outline and explosion device, service manual and catalog
Back to : Braun_Oral_Line_Carioquen | Home
Service Documentation Braun Oral-B Plaque Remover Center
Market Release 9/96
OC 9525
4714
4714
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Exploded Drawing 4714
4714 - 2
BINC Rev: 11/97 BAG Rev: 9/96
Service Documentation
Spare Parts List 4714 Part Description
Lid Spring catch Spring Jet container Back housing Screw Foot Front housing Beaker Moving knob Handle with tube Switch knob End sleeve Motor Screw Sealing set Pump, cpl. Angle piece Transformer Screw Circuit board Wall bracket Jet set ED 5 (4 pieces) Padding
Pos. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 19 20 22 23 24 25 26 27
Part Number
4723014 4525010 4525032 4723020 4723157 0031003 4803061 4714622 4714850 4723015 4714621 4714854 4803035 4723622 0034001 4723627 4714623 4714853 4723645 0031003 4723624 4723016 4723791 4723130
4714 - 3
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Exploded Drawing 4714
4714 - 4
BINC Rev: 5/99 BAG Rev: 9/96
Service Documentation
Spare Parts List 4714 Part Description
Lid Spring catch Spring Brush container Housing Bottom, cpl. Ferrite core Screw Brush, EBI 9-3 Ultra Handle with timer
Pos. No.
28 29 30 31 32 33 34 35 36 37
Part Number
4726052 4726057 4726058 4726051 4723012 4714625 4726063 0031135 order by description 4713631
4714 - 5
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Service Information 4714
Technical Data Housing: Drive: Voltage: Wattage: Impulses (rpm): Feed performance: Filling capacity: Pressure regulator: Connecting hose: Operating time: Accessories: Plastic 15 V - direct current-motor with piston pump 120 V, 60 Hz 20 W 500 - 1000 / minute electronically adjustable 350 ml/minute in position 8 600 cm3 Infinitely variable (increasing 2-8) 0.25 - 0.7 N Spiral hose with connecting wire to switch, length 1 m (stretched) max. 20 minutes, 2 h cool-time 4 jets, jet container, wall bracket for appliance
4714 - 6
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Service Information 4714
Disassembly · · · · · · · · Remove jet container (4) and beaker (9) loosen housing screws (6) and remove back housing (5). Pull mains through opening of back housing. Un-solder switch connectors in spots a and b from tube connections, slide end sleeve (13) on tube upwards and pull tube from pump connection. Carefully pull-out tube from front housing (8). Remove terminal connector from PCB (24) and remove adapter connector sideways out of front housing. Remove screws (23) from transformer (22) and take-out of front housing (8). Transformer with pump (19) including the corresponding O-rings and seals (16). Un-screw motor (14) from pump (19). Disengage angle piece (20) with seal (16e) from front housing. Loosen PCB (24) from front housing and pull-off from moving knob (10). Push moving knob out of front housing. Disengage lid (1) from front housing (snap-action). From handle with tube (11), the switch knob (12) can removed by sliding.
Assembly The assembly is made in reversed sequence. Attention should be paid to the following: · · · · · · · Connect motor by observing the correct polarity (red wire to marked connection). Slide end sleeve (13) over tube, push tube firmly over tube connector of pump and press end sleeve over connection. Press switch connections into recesses provided for in housing (areas a and b) and connect with tube connections by soldering (see wiring diagram on page 8). If PCB had been exchanged, a new PCB has to be installed as per instruction (see page 9). Install wires in the area of the mains-well by making sure, no connecting wires will be pinched between the housing parts. While closing the housing parts with screws, push spring catch (2) with spring (3) downwards. Carry-out functional tests.
4714 - 7
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Service Information 4714
4714 - 8
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Service Information 4714
Adjusting instruction · · · · · Install new PCB and place contact strip. Plug into connection and turn moving knob to "8". Connect measuring instrument with motor and switch appliance on at handle. Set voltage of motor with adjustable resistor - A - to 14 V. Press switch knob at handle and keep doing so. Set voltage of motor with adjustable resistor - B - to 14 V.
4714 - 9
BINC Rev: 9/96 BAG Rev: 9/96
Service Documentation
Service Information 4714
4714 - 10