Text preview for : 5596.pdf part of Braun Shave Line Outline and explosion device, service manual and catalog Part3
Back to : Braun Shaver.part3.rar | Home
Service Documentation Braun 255
Market Release 4/94
5596
5596
BINC Rev: 7/96 BAG Rev: 4/94
Service Documentation
Exploded Drawing 5596
5596 - 2
BINC Rev: 9/96 BAG Rev: 3/96
Service Documentation
Spare Parts List 5596 Part Description
Protective cap 100/200 series shaving foil frame 100/200 cutter block Circlip Cutter block support w/seal Coil spring Oscillating frame Motor Retaining spring PCB Insert Plug plate Housing upper part, cpl. Housing lower part Luminous rod Housing support Housing screw Shave and shape attachment Cleaning brush Coiled cord Case
Pos. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Part Number
5461038 order by description order by description 0107001 5523812 5461040 5461009 5596651 5596006 5596630 5461003 5596648 5596636 5596627 5596004 5596635 0038210 5596650 5002820 5323015 5461088
5596 - 3
BINC Rev: 7/96 BAG Rev: 11/95
Service Documentation
Service Information 5596
Description of shaver Rechargeable and cord shaver: Housing: Shaving head frame: Cutter block: Long hair trimmer Drive: Power transmission: Power supply: Charging of the shaver: Charging time: from 100 V onwards Technical data Amplitude at the cutter block: Rotational speed on accumulator drive: Current consumption on mains: operation 220 V Operating capacity after the shaver: is fully charged: 2.8 mm. approx. 6300 rpm, long-hair trimmer disengaged. max. 17 mA, long-hair trimmer disengaged. approx. 35 shaving minutes. 12 - 240 V, 50 - 60 Hz, 5 W. Plastic. Plastic with integrated shaving foil. Plastic, 30 cutter blades, 3° obliquely positioned, 10 mm diameter. Switchable through a separate switch. 1.2 V direct-current motor. to cutter block by means of eccentric and plastic oscillating frame. Supply by means of one built-in rechargeable NH-battery. is indicated by a green lamp. on 12 V approx. 20 hours. approx. 1 hour.
5596 - 4
BINC: 7/96 BAG: 9/94
Service Documentation
Service Information 5596
Dismantling: · · · · · · · · · Shaving foil frame (2) Cutter block (3) Cutter block support with foam rubber seal (5). Housing support (16). Housing upper part (13) plate (12) Oscillating frame (7) Insert (11) PCB (10) Plug plate (12) Motor (8) - remove - remove - remove circlip (4) - remove cutter block support with foam rubber seal (5) and conical coil spring (6). - remove screws (17) and take off housing support (16). - Insert a coin into the marked indentation of the plug and turn it counterclockwise. Separate housing parts from each other. - remove from housing upper part (13). - remove from housing lower pad (14). - lift out of housing lower part (14) - unsolder the connection wires from the motor (8). - remove from housing lower part (14) - pull apart the sides of the motor housing in the housing lower part (14) - remove spring frame (9) and motor (8).
Assembly: · The assembly is made in reverse order.
Attention: · · · · · After each opening of the device a new plug plate (12) has to be inserted. Insert plug plate (12) in housing lower part (14), with the unlocking-pin "A" upwards. The PCB's wires should be soldered with the right polarization to the motor (8), ("plus"connection - red color, to motor outside connection with screening provision). Insert the PCB (10) exactly into housing lower part (14) and make contact in the plug plate. For security reasons, no repairs are to be performed on the PCB (10). The PCB is protected against humidity by means of a special lacquer.
Make a function check.
5596 - 5