Text preview for : 5666.pdf part of Braun Shave Line Outline and explosion device, service manual and catalog Part3
Back to : Braun Shaver.part3.rar | Home
Service Documentation Lady Braun elegance 3
Market Release 1/85
5666
5666
BINC Rev: 7/96 BAG Rev: 1/85
Service Documentation
Exploded Drawing 5666
5666 - 2
BINC Rev: 4/97 BAG Rev: 6/92
Service Documentation
Spare Parts List 5666 Part Description
Protective cap Frame, white Shaving foil Housing upper part Damping pad 22 x 15 Coupling rod Switch knob Screw Spring catch Spring 3000 series cutter block Circlip Cutter block support Conical coil spring Foam rubber seal Adjustable spring seal Oscillating spring Motor Insulating plate Screw Circuit board, cpl. with sockets with pins Housing lower part, white Housing screw Damping pad Coiled cord Brush Case, cpl.
Pos. No.
1 2 3 16 17 19 20 27 28 29 32 33 35 37 41 42 47 48 49 51
Part Number
5666058 5666621 5666760 5666861 5209018 5860049 5666084 5420158 5660028 5660029 order by description 0107001 5666862 5666055 5410179 5300048 5300148 5667626 5420011 5424116 5666848 NLA 5666821 5660111 5260029 5001979 5002849 5666068
53 56 -
5666 - 3
BINC Rev: 7/96 BAG Rev: 5/88
Service Documentation
Service Information 5666
Dismantling: Disconnect power cord and remove shaving head frame Unscrew the two housing screws, raise the cover slightly at the top and release the cover by moving the latter towards the bottom. When conducting the oscillating spring adjustment take caution the opened up shaver is always switched on. After having loosened screws (49) remove motor with printed circuit board from the housing lower part and disconnect circuit from the motor. Reassembly: Reconnect circuit board to the motor and place the unit into the housing lower part and tighten screws. Important! Push the switch button to position "1" before remounting the housing upper part, place the upper part at the top in the housing lower part and then close the housing at the bottom. Ensure that the rubber seal is seated correctly in the housing recesses. Finally retighten the two housing screws. Carry out final test.
Attention! From May 1988 on, the way of contacting motor to PCB will be changed. The motor will be furnished with sockets and the PCB with corresponding pins. After running out of inventory, in case of a defect only motors of the new version will be delivered. In this case, also the PCB must be replaced. The PCB in the previous design can still be delivered in the future. If the PCB becomes defective, only this component needs to be exchanged.
5666 - 4
BINC Rev: 7/96 BAG Rev: 8/88
Service Documentation
Service Information 5666
Description of shaver Cord shaver: Housing: Shaving head frame: Shaving foil: Cutter block: Long-hair trimmer: Drive: Weight of shaver: Technical Data Air-gap between stator and oscillating armature: Lead angle: Resonance frequency: Amplitude at the cutter block: Amplitude at the oscillating arm: 0.15-0.2 mm (gap cannot be altered) 0.8-1.2 mm 65-67 c/s 3-3.5 blades (3-3.5 mm) 120/220 VAC 60 c/s, switch-selected Plastic Plastic with two riveted long-hair trimmer Frame version plastic, 10 mm diameter 38 mm wide. 36 cutter blades, 3° obliquely positioned Simultaneous running trimmer One radius-shaped cutting system 34 mm wide. One linear cutting system 42 mm wide. Oscillating armature motor, solderless connection Without case: 225 grams
Adjustment of the shaver is achieved by turning the oscillating spring. Check lead angle if necessary readjust. Current consumption 120 V: Current consumption 220 V: Active power: Reserve power: 180-215 mA 80-100 mA 5-7 W >= 1 W
All measurements are taken with mounted shaving head frame.
5666 - 5