Text preview for : 5667.pdf part of Braun Shave Line Outline and explosion device, service manual and catalog Part3
Back to : Braun Shaver.part3.rar | Home
Service Documentation Lady Braun elegance 2
Market Release 1/85
5667
5667
BINC Rev: 7/96 BAG Rev: 1/85
Service Documentation
Exploded Drawing 5667
5667 - 2
BINC Rev: 7/96 BAG Rev: 9/92
Service Documentation
Spare Parts List 5667 Part Description
Protective cap Frame, white Frame, brilliant white Shaving foil Housing upper part, white brilliant white Damping pad Coupling rod Switch knob, white brilliant white Screw 5 Spring catch Spring 3000 series cutter block Circlip Cutter block support Conical coil spring Foam rubber seal Adjustable spring seat Oscillating spring Motor Insulating plate Screw Circuit board, cpl. with sockets with pins Housing lower part, white brilliant white Housing screw Coiled cord Brush Bag
Pos. No.
1 2 2 3 16 17 19 20 27 28 29 32 33 35 37 41 42 47 48 49 51 53 56
Part Number
5666086 5667621 5667622 5666760 5666861 NLA 5209018 5660049 5666084 5666127 5420158 5860028 5660029 order by description 0107001 5666862 5666055 5410179 5300048 5300148 5667626 5420011 5424116 5667854 5667856 5666821 5868891 5860111 5001981 5002849 5661001
5667 - 3
BINC Rev: 7/96 BAG Rev: 8/88
Service Documentation
Service Information 5667
Description of shaver Cord shaver: Housing: Shaving head frame: Shaving foil: Cutter block: Long-hair trimmer: Drive: Weight of shaver: Technical Data Air-gap between stator and oscillating armature: Lead angle: Resonance frequency: Amplitude at the cutter block: Amplitude at the oscillating arm: 0.15-0.2 mm (gap cannot be altered) 0.8-1.2 mm 65-67 c/s 3-3.5 blades (3-3.5 mm) 120/220 VAC 60 Hz Plastic Plastic with one riveted long-hair trimmer Frame version plastic, 10 mm diameter 38 mm wide. 36 cutter blades, 3° obliquely positioned Simultaneous running trimmer One radius-shaped cutting system 34 mm wide. Oscillating armature motor, solderless connection 225 grams
Adjustment of the shaver is achieved by turning the oscillating spring. Check lead angle if necessary readjust. Current consumption 120 V: Active power: Reserve power: 180-215 mA 5-7 W 1W
All measurements are taken with mounted shaving head frame.
5667 - 4
BINC Rev: 7/96 BAG Rev: 5/88
Service Documentation
Service Information 5667
Dismantling: Disconnect power cord and remove shaving head frame. Unscrew the two housing screws, raise the cover slightly at the top and release the cover by moving the latter towards the bottom. When conducting the oscillating spring adjustment take caution the opened up shaver is always switched on. After having loosened screws (49) remove motor with printed circuit board from the housing lower part and disconnect circuit from the motor. Reassembly: Reconnect circuit board to the motor and place the unit into the housing lower part and tighten screws. Important! Push the switch button to position "1" before remounting the housing upper part, place the upper part at the top in the housing lower part and then close the housing at the bottom. Ensure that the rubber seal is seated correctly in the housing recesses. Finally retighten the two housing screws. Carry out final test.
Attention! From May 1988 on, the way of contacting motor to PCB will be changed. The motor will be furnished with sockets and the PCB with corresponding pins. After running out of inventory, in case of a defect only motors of the new version will be delivered. In this case, also the PCB must be replaced. The PCB in the previous design can still be delivered in the future. If the PCB becomes defective, only this component needs to be exchanged.
5667 - 5