Text preview for : cd050103.pdf part of Panasonic NV-FJ632EE NV-FJ632EE.part3
Back to : NV-FJ632EE.part3.RAR | Home
No. Port Name 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 LC.OSC OUT RESET(L) 4FC.LPF OSD.FSC IN 5V(OSD) CVIN GND(OSD) LECHA 20M.START(H) MD0 CVOUT HLF SECAM.V.IN GND S TAB(L) UNLOADING(H) LOADING(H) C.SYNC EX.FF/REW(L) PAL-I/BG/DK(SYS4) SECAM/PAL(SYS2) SLEEP(L)
I/O
Description Input terminal for microprocessor reset. 4fc clock input terminal OSD clock input terminal 5V input terminal Input terminal for Composite video signal. GND Input terminal for Composite video signal.(White level) Switching terminal for stertting Mode.(High speed/Low speed) Mode setting terminal for flash over-write.
P-OFF P-Save P-FAIL Reset --In ----------------------In In Low Low In Low --In ----------------------In In Low Low In Low --In ----------------------In In Low Low In Low Low Low Low --In ----------------------In In Low Low In Low Low Low High
O The oscillation output terminal for OSD dot clock. I I I I I I I I I
O Output terminal for CG Video. O LPF connecting terminal for the slicer. (For OSD dot clock.) I I I O O I I Chrominance input terminal for SECAM super impose. Connect to GND Input terminal for the prevention tab. [EXIST] :LOW [NO EXIST] :HIGH Control terminal for loading motor. [Reverse rotation / brake] : "High" Control terminal for loading motor. [forward rotation / brake] : "High" Input terminal for composite V-sync signal. Filter control terminal for PB-CTL signal in FF/REW.
O Output terminal for TV broadcast system switching signal for video circuit control. O Output terminal for TV broadcast system switching signal for video circuit control. Output terminal for super power save mode setting. O P-OFF in the super power save mode.................. "Low". O Switching terminal for NTSC FM Audio trap filter in PB. [VV (PB,Trick_PB/A-DUB, A-DUB-PS) mode and CTL is 60Hz] : "High" [Other than above condition] : "Low" Switching terminal for Bias oscillation noise filter in A-DUB mode. [ADUB/ADUB-PS(Including Assemble/syncro/AV-Insert)] : "High" [Other than above condition] : "Hi-Z"
Not fix Low Not fix Low High Low
73
PB60Hz(H)
Low
Low
Low
Low
74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
ADUB(H) N.C(VBI1) P FAIL IR P50 OUT CAP.ET CYL.ET DIGI.LINK HALF_WAVE(H) CAP.R/F 125Hz SHORT_DN N.C N.C N.C FLD/T2 CLK FLD/T2 DATA IN
O
Hi-Z Low In In 0V Low In Low
Hi-Z Low In In 0V Low In Low
Hi-Z Low In In Low Low Low In Low Low In Low Low Low Low In
Hi-Z Low In In Low 0V 4.213V Low In Low Low In Low Low Low Low In
O Fix to Low. I I Input terminal for Interrupt signal for power fail detection. Input terminal for Interrupt signal from IR sensor emitted by Remo-Con.
O Output terminal for Project 50 serial data. O Output terminal for Capstan Torque command. O Output terminal for Cylinder Torque command. O Control signal for switching IR sensor.[only LOEWE model] O Switching terminal for capstan driver speed mode.(FAST/SLOW) O Switching terminal for capstan motor rotating direction. O 125Hz pulse output terminal for clock adjustment. I Short Circuit detection terminal for oscillation circuit in REC. *When the "BIAS(H)" is "Low" and this terminal is "High", "F08" is displayed. *When the "BIAS(H)" is "High" and this terminal is "low", "F07" is displayed.
Not fix Low
4.213V 4.213V Low
Not fix Low In Low Low Low In Low Low Low
-- Fix to Low. -- Fix to Low. -- Fix to Low. O Serial clock output terminal for FIP driver and TEST_2(Factory use). I Serial data input terminal for FIP driver and TEST_2(Factory use).
Not fix Low Not fix In