Text preview for : STUDIOWORKS_CB563C.pdf part of lg studioworks 563 schema monitor LG
Back to : STUDIOWORKS_CB563C.pdf | Home
SPECIFICATIONS
1. PICTURE TUBE Size DefIection Angle Neck Diameter Dot Pitch Face Treatment Low Radiation
: 15 inch (Flat Square Tube) : 90° : 29.1 mm : 0.28 mm : AR-ASC (Anti-Reflection and Anti-Static Coating) : MPR-II
3-2. Power Consumption
MODE NORMAL (ON) STAND-BY SUSPEND OFF H/V SYNC ON/ON OFF/ON ON/OFF OFF/OFF POWER CONSUMPTION LED COLOR GREEN
less than 75 W less than 15 W
AMBER
less than 15 W less than 5W
AMBER
2. SIGNAL 2-1. Horizontal & Vertical Sync 1) Input Voltage Level : Low= 0.8V, High= 2.0V 2) Sync Polarity : Positive or Negative 2-2. Video Input Signal 1) Voltage Level a) Color 0, 0 b) Color 7, 0 c) Color 15, 0 2) Input Impedance 3) Video Color 4) Signal Format
: 0 ~ 0.7 Vp-p : 0 Vp-p : 0.467 Vp-p : 0.7 Vp-p : 75 : R, G, B Analog : Refer to the Timing Chart
4. DISPLAY AREA 4-1. Active Video Area : · 285 x 215 mm (11.22" x8.46") - Max Image Size · 270 x 195 mm (10.63" x 7.68") - Preset Image Size 4-2. Display Color : Full Colors 4-3. Display Resolution : 1024 x 768 / 75Hz (Non-Interlace) 4-4. Video Bandwidth : 78 MHz 5. ENVIRONMENT 5-1. Operating Temperature: 15°C ~ 30°C (59°F ~ 86°F) (Ambient) 5-2. Relative Humidity : 8%~ 80% (Non-condensing) 5-3. Altitude : 3,000 m 6. DIMENSIONS (with TILT/SWIVEL) Width : 356.0 mm (14.01") Depth : 395.0 mm (15.55") Height : 371.0 mm (14.60") 7. WEIGHT (with TILT/SWIVEL) Net Weight : 11.7 kg (25.79 lbs) Gross Weight : 13.2 kg (29.10 lbs)
2-3. Signal Connector 15-pin D-Sub Connector (Attached Type) 2-4. Scanning Frequency Horizontal Vertical
: 30 ~ 61 kHz : 50 ~ 120 Hz
3. POWER SUPPLY 3-1. Power Range AC 100~240V (Free Voltage), 50/60Hz, 1.5A Max.
-2-
TIMING CHART
VIDEO
B A
C
E D F
SYNC
FACTORY PRESET MODE MODE
MARK H O R I Z O N T A L
MODE 1 --
MODE 2 -- 31.470 31.780 25.420 6.260 0.640 3.810 1.910 + 70.080 14.270 12.710 1.557 0.413 0.064 1.080 720 x 400 70Hz Yes
MODE 3 -- 37.50 26.670 20.320 6.350 0.51 2.03 3.810 -- 74.990 13.335 12.802 0.533 0.026 0.080 0.427 640 x 480 75Hz Yes
MODE 4 -- 43.269 23.112 17.778 5.334 1.556 1.556 2.222 -- 85.008 11.764 11.093 0.670 0.023 0.069 0.578 640 x 480 85Hz Yes
MODE 5 + 46.880 21.330 16.160 5.170 0.320 1.620 3.230 + 75.010 13.331 12.798 0.533 0.021 0.064 0.448 800 x 600 75Hz Yes
MODE 6 + 53.674 18.631 14.222 4.409 0.569 1.138 2.702 + 85.061 11.756 11.179 0.578 0.019 0.056 0.503 800 x 600 85Hz Yes
MODE 7 + 60.020 16.660 13.000 3.660 0.200 1.220 2.240 + 75.030 13.328 12.795 0.533 0.017 0.050 0.466 1024 x 768 75Hz Yes
Sync Polarity Frequency Total Period Video Active Time Blanking Time Front Porch Sync Duration Back Porch Sync Polarity
kHz µs µs µs µs µs µs E A B C D F
31.469 31.778 25.422 6.356 0.636 3.813 1.907 --
V E R T I C A L
Frequency Total Period Video Active Time Blanking Time Front Porch Sync Duration Back Porch
Hz ms ms ms ms ms ms E A B C D F
59.940 16.683 15.253 1.430 0.318 0.064 1.048 640 x 480 60Hz Yes
Resolution Recall
-4-
CONTROL LOCATIONS
1
23
4
LED
5
NO. 1 2 3
Ref. No. SW5 SW4 SW3
Control Function MENU BUTTON OSD SET/ADJUSTMENT(LEFT) OSD SET/ADJUSTMENT(RIGHT)
NO. 4 5
Ref. No. SW2 SW1
Control Function OSD SELECT POWER BUTTON
-9-
WIRING DIAGRAM
P501
S+ S
WG1 P702 P402
P902 AC Socket
FBT
TO G2
Signal Cable
P302
CDT EARTH P1
P301
- 10 -
DISASSEMBLY
1. TILT/SWIVEL REMOVAL 1) Set the monitor face downward. 2) Pressing the latch (a), carefully remove the Tilt/Swivel by pulling it upward. 2. BACK COVER REMOVAL 1) Remove four screws (a). 2) Slide the Back Cover away from the Front Cabinet of the monitor.
(a) (a) (a) (a) (a)
3. TOTAL CHASSIS ASSEMBLY REMOVAL 1) Remove connector (a) from the DY Assembly screw. 2) Disconnect P2(CDT EATH) and four pins (b) from the Video PCB. 3) Carefully separate the CDT Board Assembly from the CDT neck. 4) Discharge the remaining static electricity by shorting between the Anode Cap and the CDT ground. 5) Disconnect the Anode Cap from the CDT. 6) Disconnect P902 (Degaussing pin), P701 (DY pin), and P501 from the Main PCB. 7) Remove four screws (c). 8) Remove the Total Chassis Assembly from the Main Frame.
M EN U SE LE CT
Anode Cap
(b)
DY Assembly Screw
(a)
(b)
P2
(c)
P701
(c)
P702 P402
P902 P501
(c)
(c)
- 11 -
4. VIDEO PCB ASSEMBLY REMOVAL 1) Disconnect P301, P302, P1 from the Video PCB. 2) Remove five screws (a). 3) Remove the Video PCB Assembly.
5. BOTTOM BRACKET REMOVAL 1) Remove four screws (a). 2) Remove the Bottom Bracket.
(a) (a) (a) (a)
P302 P1 P301
(a)
(a)
P702 P402
(a)
- 12 -
105V H.V Heater ( 6.3V ) Signal Cable R G B DY VIDEO PRE-AMP (IC302) VIDEO MAIN AMP (IC303) CDT
.CONTRAST
.BRIGHTNESS
H-Sync Sig V-Sync Sig I2C DATA(SDA) I2C CLOCK(SCL) G1 Screen 6.3V 15V
.H-POSITION
.H-SIZE
.V-POSITION
.V-SIZE
.PINCUSHION
.TRAPEZOID
MICOM (IC401) 5V I2C OSD IC (IC301) I2C
R/G/B Drive/Contrast Cut-Off
.PIN BALANCE
5V
.PARALLELOGRAM
SCL / SDA H/V Sync, PWM Control 15V
Focus
.V-MOIRE
.COLOR
.RECALL
.LANGUAGE
.DEGAUSS
.INFORMATION
12V E2PROM (IC402) 15V Vout I2C H/V Sync 105V 60V SMPS TRANS (T901) 15V 6.3V -12V 5V B-DRV H-DRV H/V Sync Processor ( IC701 ) TDA9115 I2C
X-RAY Protection Circuit 15V V-OUT ( IC601) TDA8172
Vertical Blanking, Brightness Control - 120V 40V
OPTION
TILT COIL
BLOCK DIAGRAM
DEGAUSSING COIL
- 13 15V 5V Regulator DPM CONTROL CIRCUIT 60V D/D Feed Back 12V Regulator 12V
6.3V
TILT Control Circuit
Degaussing Circuit
FBT ( T701 ) H-OUT ( Q706) B+ H-Linearity Correction
15V
Line Filter
DC/DC Converter
Auto Beam Limit 600V Screen Control Circuit
AC 90~264V INPUT
SMPS CONTROL (IC901)
DESCRIPTION OF BLOCK DIAGRAM
1. Line Filter & Associated Circuit. This is used for suppressing noise of power input line flowing into the monitor and/or some noise generated in this monitor flowing out through the power input line. That is to say, this circuit prevents interference between the monitor and other electric appliances. 2. Degauss Circuit & Coil. The degauss circuit consists of the degaussing coil, the PTC(Positive Temperature Coefficient) thermistor(TH901), and the relay(RL901). This circuit eliminates abnormal color of the screen automatically by degaussing the shadow mask in the CRT during turning on the power switch. When you need to degauss in using the monitor, select DEGAUSS on the OSD menu. 3. SMPS(Switching Mode Power Supply). This circuit is working of 90~264V AC(50/60Hz). The operation procedure is as follows: 1) AC input voltage is rectified and smoothed by the bridge diodes (D901~D904) and the capacitor (C908). 2) The rectified voltage(DC) is applied to the primary coil of the transformer(T901). 3) The control IC(IC901) generates switching pulse to turn on and off the primary coil of the transformer (T901) repeatedly. 4) Depending on turn ratio of the transformer, the secondary voltages appear at the secondary coils of the transformer(T901). 5) These secondary voltages are rectified by each diode(D941, D951, D961, D971, D953) and operate other circuit. (horizontal and vertical deflection, video amplifier, ...etc.) 4. X-ray Protection. If the high voltage of the FBT reaches up to 29kV (abnormal state), Q807 operates and IC401(MICOM) pin 22 come to low level. Then MICOM control IC701 (Deflection controller) to stop Horizontal drive pulse and stop Horizontal Deflection. 5. Micom(Microprocessor) Circuit. The operating procedure of Micom(Microprocessor) and its associated circuit is as follows: 1) H and V sync signal is supplied from the signal cable. 2) The Micom(IC401) distinguishes polarity and frequency of H and V sync. 3) The Micom sets operating mode and offers the controlled data. (H-size, H-position, V-size, ... etc.) 4) The controlled data of each mode is stored in itself. 5) User can adjust screen condition by each OSD function. The data of the adjusted condition is stored in EEPROM(IC402). 6. Horizontal and Vertical Oscillation. This circuit generates the horizontal pulse and the vertical pulse by taking the H and V sync signal. This circuit consists of the TDA9115(IC701) and the associated circuit. 7. D/D(DC to DC) Converter. This circuit supplies DC voltage to the horizontal deflection output circuit by increasing DC 60V which is the secondary voltage of the SMPS in accordance with the input horizontal sync signal. 8. Side-Pincushion & Trapezoid Correction Cirucit. This circuit improves the side-pincushion and the trapezoid distortion of the screen by mixing parabola and saw-tooth wave to output of the horizontal deflection D/D converter which is used for the supply voltage(B+) of the deflection circuit. 9. Horizontal Deflection Output Circuit. This circuit makes the horizontal deflection by supplying the saw-tooth current to the horizontal deflection yoke. 10. High Voltage Output & FBT(Flyback Transformer). The high voltage output circuit is used for generating pulse to the primary coil of the FBT(Flyback Transformer (T701)). A boosted voltage(about 24.5kV) appears at the secondary of the FBT and it is supplied to the anode, focus, and screen voltage of the CRT. 11. H-Linearity Correction Circuit. This circuit corrects the horizontal linearity for each horizontal sync frequency. 12. Vertical Output Circuit. This circuit takes the vertical ramp wave from the TDA9115(IC701) and performs the vertical deflection by supplying the saw-tooth current to the vertical deflection yoke. 13. H & V Blanking and Brightness Control. Blanking circuit eliminates retrace line by supplying negative pulse to the G1 of the CRT. And Brightness circuit is used for control of the screen brightness by changing DC level of the G1. 14. Image Rotation (Tilt) Circuit. (OPTION) This circuit corrects the tilt of the screen by supplying the image rotation signal to the tilt coil which is attached near the deflection yoke of the CRT. 15. Video Pre-Amp Circuit. This circuit amplifies the analog video signal from 0-0.7V to 0-4V. It is operated by taking the clamp, R, G, B drive and contrast signal from the Micom(IC401). 16. Video Output Amp Circuit. This circuit amplifies the video signal which comes from the video pre-amp circuit and amplified it to applied the CRT cathode.
- 14 -
ADJUSTMENT
GENERAL INFORMATION
All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes several adjustments may be required. Adjustment should be following procedure and after warming up for a minimum of 30 minutes. · Alignment appliances and tools. - IBM compatible PC. - Programmable Signal Generator. (eg. VG-819 made by Astrodesign Co.) - EPROM or EEPROM with saved each mode data. - Alignment Adaptor and Software. - Digital Voltmeter. - White Balance Meter. - Luminance Meter. - High-voltage Meter.
AUTOMATIC AND MANUAL DEGAUSSING The degaussing coil is mounted around the CDT so that automatic degaussing when turn on the monitor. But a monitor is moved or faced in a different direction, become poor color purity cause of CDT magnetized, then press DEGAUSS on the OSD menu.
5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15)
COMMAND START Y(Yes) command. DIST. ADJ. FOS. ADJ command. Adjust V-SIZE as arrow keys to 200±1mm. Adjust V-POSITION as arrow keys to center of the screen. Adjust H-SIZE as arrow keys to 270±1mm. Adjust H-POSITION as arrow keys to center of the screen. Adjust S-PCC (Side-Pincushion) as arrow keys to be the best condition. Adjust TRAPEZOID as arrow keys to be the best condition. DIST. ADJ. BALANCE command. Adjust parallelogram as arrow keys to be the best condition. PRESET EXIT Y (Yes) command.
ADJUSTMENT PROCEDURE & METHOD
- Install the cable for adjustment such as Figure 1and run the alignment program on the DOS for IBM compatible PC. - Set external Brightness and Contrast volume to max position. 1. Adjustment for B+ Voltage. 1) Display cross hatch pattern at Mode 7. 2) Adjust voltage to 60V±0.2Vdc with VR901. 2. Adjustment for High-Voltage. 1) Run alignment program for CB563C on the IBM compatible PC. 2) Display cross hatch pattern at Mode 7. 3) DIST.ADJCTRL PWM High Voltage Command. 4) Adjust High Voltage to 24.5kV±0.1 kVdc. 5) Press Enter Key. 3. Adjustment for Factory Mode (Preset Mode). 1) Display cross hatch pattern at Mode 1~7. 2) Run alignment program for CB563C on the IBM compatible PC. 3) EEPROM ALL CLEAR Y(Yes) command. Do not run this procedure unless the EEPROM is changed. All data in EEPROM (mode data and color data) will be erased. 4) Power button of the monitor turn off turn on.
4. Adjustment for White Balance and Luminance. 1) Set the White Balance Meter. 2) Press the DEGAUSS on the OSD menu for demagnetization of the CDT. 3) COLOR ADJ. LUMINANCE command of the alignment program. 4) Set Brightness and Contrast to Max and ABL to 145 (decimal) position. 5) Display color 0,0 pattern at Mode 7. 6) COLOR ADJ. BIAS ADJ. command of the alignment program. 7) Check whether green color or not at R-BIAS and BBIAS to min position and G-BIAS to 127(7F) to position. Set Sub-Brightness to 127(Decimal). Adjust G2(Screen) Volume on FBT to 2.0± 0.30FL of the raster luminance. Check it's not green color. 8) Adjust R-BIAS and B-BIAS command to x=0.283± 0.010 and y=0.298 ±0.010 on the White Balance Meter with PC arrow keys. 9) Adjust SUB-Brightness command to 0.4±0.05FL of the raster luminance. 10) Display color 15,0 box pattern (70x70mm) at Mode 7. 11) DRIVE ADJ command. 12) Set SUB-Contrast 58 (decimal) position. 13) Set G-DRIVE to 160 (decimal) at DRIVE of the alignment program. 14) Adjust R-DRIVE and B-DRIVE command to white balance x=0.283±0.003 and y=0.298±0.003 on the White Balance Meter with PC arrow keys.
- 15 -
15) Adjust SUB-CONTRAST command to 47±0.5FL of the color 15,0 box pattern (70x70mm) luminance at mode 7. 16) Display color 15,0 full white patten at Mode 7. 17) COLOR ADJ. LUMINANCE ABL command. 18) Adjust ABL to 33±0.5FL of the luminance. 19) Exit from the program.
5. Adjustment for Focus. 1) Display H character in full screen at Mode 7. 2) Adjust two Focus control on the FBT that focus should be the best condition.
C
RS
23
2C
220
VG
S MO NI
A
TO
R
ST
B F
E
A
9 15 10 5 11 6 1 5 6 1
C
13 25 1 14
5V
OFF
ON
F
5V ON 4.7K 4.7K 4.7K 74LS06 74LS06
5V
E
OFF
B
Figure 1. Cable Connection
- 16 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER (POWER INDICATOR OFF)
CHECK FUSE OK?
NO
TROUBLE IN FUSE (F901)
YES
CHECK C908 VOLTAGE? (AC120V: 160VDC, AC220V: 304VDC)
NO
TROUBLE IN D901, D902, D903, D904
YES
CHECK IC901 PIN 6 WAVEFORM (SQUARE WAVE COMES OUT?)
NO
TROUBLE IN IC901
YES
CHECK D941, D951, D961, D971 VOLTAGE?
NO
TROUBLE IN D941, D951, D961, D971
YES
TROUBLE IN IC950, IC952, Q952, Q951, Q942, Q941
- 17 -
2. NO CHARACTER
NO CHARACTER
CHECK IC302 PIN 20(6.3V) ? YES
NO
TROUBLE IN P302 6.3V LINE
CHECK IC302 PIN 1, 3, 5?
NO
TROUBLE IN PC SIGNAL, P301 SIGNAL CABLE
YES
CHECK IC302 PIN 14, 16, 18 ?
NO
TROUBLE IN IC302
YES CHECK IC303 PIN 4 (105V) PIN 8 (15V) ?
NO
TROUBLE IN P303 15V LINE/ 105V LINE
YES
CHECK IC303 PIN 1, 5, 11 ?
NO
TROUBLE IN IC303
YES CHECK R, G, B CATHODE VOLTAGE? YES TROUBLE IN CRT SOCKET TROUBLE IN R341~R343, R351~R353, L301~L303, D307~D312
NO
- 18 -
3. NO RASTER
NO VIDEO (POWER INDICATOR ON)
CHECK POWER INDICATOR GREEN or ORANGE?
ORANGE
DPM MODE (NO H and/or V SYNC)
GREEN
CHECK D712 ANODE (-120V)?
NO
TROUBLE IN D712
YES
CHECK G1 VOLTAGE? (-35~-15V)
NO
TROUBLE IN Q704
YES
CHECK CDT HEAT VOLTAGE? (6.3V)
NO
TROUBLE IN D941, Q942, Q941
YES
TROUBLE IN CDT
- 19 -
4. NO HORIZONTAL DEFLECTION
NO H-DEFLECTION (ONE VERTICAL LINE)
CHECK Q706?
NO
TROUBLE IN Q706
YES
CHECK B+ VOLTAGE (50V)?
NO
TROUBLE IN 50V LINE
YES
CHECK T701(FBT) PIN 2 (31KHZ 70V, 60KHZ 135V) ?
NO
TROUBLE IN Q719, Q720, D710
YES
CHECK Q705 COLLECTOR WAVEFORM?
NO
TROUBLE IN Q705
YES
TROUBLE IN T701, P701
- 20 -
5. TROUBLE IN H-LINEARITY
UNBALANCED OF H-LIN.
CHECK IC401 PIN 12,14 ?
NO
TROUBLE IN IC401 (MICOM)
YES
CHECK Q711, Q713, Q714, Q716?
NO
TROUBLE IN Q711, Q713, Q714, Q716
YES
CHECK L703?
NO
TROUBLE IN L703
YES
Cs SIGNAL TABLE
HORIZONTAL FREQUENCY(fH)
Cs1 L H L H
Cs3 L L H H
TROUBLE IN C722, C723, C729
29K 36K 39K 49K
~ ~ ~ ~
35.9K 38.9K 48.9K 60.0K
- 21 -
6. NO VERTICAL DEFLECTION
NO V-DEFLECTION (ONE HORIZONTAL LINE)
CHECK IC601 PIN 3 (15V)?
NO
TROUBLE IN D602 15V LINE
YES
CHECK IC601 PIN 7 (40V)?
NO
TROUBLE IN HIGH-VOLTAGE OUT CIRCUIT(FBT), D721, R603
YES
CHECK IC701 PIN 12, 13?
NO
TROUBLE IN IC701
3V
YES
TROUBLE IN IC601, V-CIRCUIT
- 22 -
7. TROUBLE IN OSD
NO OSD
(ENTER BUTTON MUST BE PRESSED.)
CHECK IC301 B+ ?
NO
TROUBLE IN 5V LINE
DC 5V
YES
CHECK IC301 PIN 5, 10 WAVEFORM?
Pin 10
5V
NO
TROUBLE IN IC601 PIN6 (V-FBP), T701 40V LINE (H-FBP)
Pin 5
YES
CHECK IC301 PIN 12 WAVEFORM ?
H+V 5V
NO
TROUBLE IN IC302, IC301
YES
CHECK IC301 PIN 13, 14, 15 ?
H+V 5V
NO
TROUBLE IN IC301, IC302
YES
TROUBLE IN OSD PERIPHERAL CIRCUIT
- 23 -
8. TROUBLE IN DPM
OFF MODE FAILURE
(NO OFF MODE.)
CHECK IC401 (MICOM) PIN 40, 41(H/V INPUT) SIGNAL?
NO
INPUT H/V SYNC SIGNAL
CHECK PC, (PC IS NOT GOING INTO DPM OFF MODE)
YES
H/V SYNC
CHECK IC401 PIN 8 WAVEFORM?
5V
NO
TROUBLE IN X401
YES
24MHz
CHECK IC401 (MICOM) PIN 15, 17 ? SEE DPM TABLE YES
NO
(DPMF: 0V)
TROUBLE IN IC401 (MICOM)
CHECK B+ LINE (6.3V,15V, 105V) ?
NO
TROUBLE IN Q941, Q942, Q951, Q952
YES Mode TROUBLE IN PC Item DPMF H H H L
DPM TABLE DPMS H L L L LED GREEN ORANGE ORANGE ORANGE
NORMAL STAND-BY SUSPEND OFF
- 24 -
9. NO DEGAUSSING
NO DEGAUSSING
(DEGAUSS ON THE OSD MENU MUST BE PRESSED.)
CHECK IC401 PIN 28 (0V)?
NO
TROUBLE IN IC401 (MICOM)
YES
CHECK Q953 COLLECTOR VOLTAGE? DC 15V YES
NO
TROUBLE IN Q953
CHECK P902 ?
NO
TROUBLE IN P902
YES
CHECK RL901?
NO
TROUBLE IN RL901
YES TROUBLE IN TH901, DEGAUSSING COIL
- 25 -
10. NO TILT (NO ROTATION )
NO TILT (NO ROTATION)
CHECK Q504(COLLECTOR) WAVE FORM ?
NO
TROUBLE IN IC401 (MICOM)
12V
YES
CHECK 15V LINE AND 6.3V LINE ?
NO
TROUBLE IN 15V LINE, 6.3V LINE
YES
CHECK Q503 EMITTER VOLTAGE ?
NO
TROUBLE IN Q501~Q503
YES
TROUBLE IN P501, TILT COIL, D501
- 26 -
EXPLODED VIEW
EXPLODED VIEW PARTS LIST
Ref. No. Part No.
3091TKB031A 3091TKB036D 1 3091TKB036E 3091TKB036F 3091TKB036B 2423GB0A8AW 2423GB0A8CF 2 2423GB0A59A 2423GB0A58A 6318TO1502B 6318R15001A 3 4 5 6 339-002D 6868T15002A 150-A29A 6174Z-1035A 6620TKB002A 4950TKS155E 332-102F 3809TKB017A 10 11 3809TKB021A 3809TKB021C 332-102F 3043TKK063B 12 3043TKK071A 3043TKK071B 3043TKK071D 3313T15067F
Description
CABINET ASS'Y, CB573D BRAND 3090TKB027A(LGENT) -For Rusia:S/W 563N(CB563C-NA) CABINET ASS'Y, CB563C BRAND B031 LGEIL ABS 85964 -For W/wide:S/W 563N(CB563C-NA) CABINET ASS'Y, CB563C BRAND B031 S/W563A 320T 85964 -For W/wide:S/W 563A(CB563C-AA) CABINET ASS'Y, CB563C LANIX B031 320T 13258(20141)COLOR -For LANIX:(LN563N) CABINET ASS'Y, CB563C BRAND B031 S/W563A ABS85964 -For Mexico:S/W 563A(CB563C-AA) CDT SET, M36LBL803X31NLLA -For Northern Hemisphere:S/W 563N(CB563C-NA) CDT SET, M36LBL803X31NLLM -For India CDT SET, M36LBL503X 34RLLD -For Equatorial:S/W 563A(CB563C-AA) CDT SET, M36LBL503X 34NLLD -For Northern Hemisphere:S/W 563A(CB563C-AA) CDT (CIRC), M36KXU110XX61(AG) ORION 69KHZ 29.1MM -For LANIX:LN563N(LN563N) CDT (CIRC), M36KXU120XX51(G) ORION 61KHZ 29.1MM -For Mexico:S/W 563A(CB563C-AA) SCREW ASS'Y, PHP+5x30(FZMY)+GW18 CDT EARTH, CB571 TIN WIRE BRAID(64) DEGAUSSING COIL, 870MM 8.4 OHM 0.4MM FBT, FMMTC81-M1035A SOCKET(CIRC), POWER BCP-03A-3 BAE EUN AC UNIVERSAL 3PIN BLACK METAL, SHIELD BOTTOM, "D" CKD KCB563C SCREW, PTP+4x20BP(MSWR/FZMY) BACK COVER ASS'Y, CB573D 3808TKB 020A -For Rusia BACK COVER ASS'Y, CB563 B024 ABS 85964 -For W/wide BACK COVER ASS'Y, CB563C B024 320T LANIX 13258(20141)COLOR -For LANIX SCREW, PTP+4x20BP(MSWR/FZMY) TILT SWIVEL ASS'Y, KCB773D, 60HR(85964)NT LOCAL -For Rusia TILT SWIVEL ASS'Y, CB563C,T051 B046 HIPS 85964 -For Mexico TILT SWIVEL ASSY, KCB563C B046, T051 HIPS 85964 SP -For W/wide TILT SWIVEL ASSY, CB563C B046,T051 60HR LANIX 13258(20141)COLOR -For LANIX MAIN TOTAL ASS'Y, KCB563C LGENT WITHOUT TILT BRAND CA-76 -For Rusia MAIN TOTAL ASS'Y, CB563C KXLCMT BRAND CA-76 LGENT -For China MAIN TOTAL ASS'Y, CB563C SXJIML BRAND CA-76 LGEIL -For India MAIN TOTAL ASS'Y, CB563C BRAND CA-76 -For Asia, Centeral Asia MAIN TOTAL ASSY, CB563C KXLVMD BRAND CA-76 -For U.S.A MAIN TOTAL ASSY, CB563C BRAND CA-76 -For LANIX MAIN TOTAL ASSY, CB563C BRAND CA-76 -For Mexico PCB ASS'Y, VIDEO, CB563C LGENT KXLCMT BRAND -For Rusia PCB ASS'Y, VIDEO, CB563C LGEIL SXJIML BRAND CA-76 TOTAL -For India PCB ASS'Y, VIDEO, CB563C KXLVMD BRAND CA-76 TOTAL -For Asia, Centeral Asia, U.S.A PCB ASS'Y, VIDEO, CB563C VIDEO TOTAL BRAND -For LANIX, Mexico PCB ASS'Y, MAIN, KCB563C KXLRMT BRAND CA-76 HAND -For Rusia PCB ASS'Y, MAIN, CB563C LGENT KXLCMT BRAND CA-76 HAND -For China PCB ASS'Y, MAIN, CB563C LGEIL SXJIML BRAND CA-76 HAND -For India PCB ASS'Y, MAIN, CB563C KXJIAD BRAND CA-76 HAND -For Asia, Centeral Asia PCB ASS'Y, MAIN, CB563C KXLVMD BRAND CA-76 HAND -For U.S.A PCB ASS'Y, MAIN, CB563C KXLMMM BRAND CA-76 HAND -For LANIX PCB ASS'Y, MAIN, CB563C KQLPAM BRAND CA-76 HAND -For Mexico
11 3
B
6 4 7 5 10
7 8 9
C
2
A
9 8
3313T15067D 3313T15067E A 3313T15067Q 3313T15067K 3313T15067L 3313T15067M 6871TVT200C 6871TVT200D 6871TVT200F 6871TVT200G 6871TMH202F 6871TMH202D 6871TMH202E C 6871TMH202Q 6871TMH202K 6871TMH202L 6871TMH202M
12 1
M EN U SE LE CT
B
9
3.40V
85.2V
42V
15V V
0V(Grand)
- 45V - 5V - 0V - 7V
50.4V
15.6V
1.88V