Text preview for : Audio Power Amplifiers-Philips.pdf part of Philips Audio Power Amplifiers-Philips Audio Power Amplifiers-Philips e-book
Back to : Audio Power Amplifiers-Ph | Home
Audio Power
Audio power amplifiers
Designer's guide - October 1996
AUDIO AMPLIFIER ICS DESIGNER'S GUIDE Contents
Section 1 2 Page
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Product survey and page reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 In application sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 In power output sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Audio amplifier ICs for portable radio/audio equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Audio amplifier ICs for car radios/power boosters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Audio amplifier ICs for mains-powered systems including hi-fi and TV sound . . . . . . . . . . . . . . . . 5-1
3 4 5
Appendices 1 Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Application notes and leaflet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 2 Index of audio amplifier ICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
NOTE Purchase of Philips I2C components conveys a license under the Philips I2C patent to use the components in the I2C system, provided the system conforms to the I2C specifications defined by Philips.
Audio Amplifier ICs
1-1
INTRODUCTION
1
INTEGRATED POWER WITH PHILIPS AUDIO AMPLIFIER ICs
Few people realize that one of the world's first ICs was an audio power amplifier from Philips. This delivered a mere 25 mW into a hearing-aid earpiece and incorporated just three transistors and 2 resistors. Not surprisingly, we've made many advances since that initial introduction. Advances that have led to ICs such as the TDA8551 incorporating digital volume control with a control range of more than 80 dB. Or the hi-fi TDA1514A, which can deliver 50 W more than two thousand times the power of that first integrated amplifier. These are just two of the extensive range of audio ICs we now supply for a whole host of applications including portable radio and recorders, car radios, multimedia systems, hi-fi TV, radio and music centres, and digital audio systems. What's more, advanced internal protection circuitry completely eliminates danger of damage from thermal runaway, shortcircuits and electrostatic discharge. Providing a level of circuit reliability formerly the exclusive preserve of professional systems, and, moreover, providing you with a solid guarantee of quality and reliability in your own systems.
A valuable aid to designers
In the following pages you'll find our complete range of audio amplifiers. Intended principally as a designer's first selection guide, the pages give the most important parameters, or at least, those that feature prominently when design criteria are initially being considered. Used in conjunction with our Data Handbook IC01 (which gives more detailed information), this guide provides audio system designers with a ready means of selecting the most appropriate components for their designs. The publication is divided into three application areas: portable radio/audio, car radio and mains-powered systems. Many products, however, may be suitable for several application areas: car audio systems and mains-powered multimedia PCs for example. What's more, many of today's applications for audio amplifier ICs, e.g. musical greeting cards, were unheard of just a few years ago. This means that any subdivision such as that given in this guide can be only a preliminary indication of a product's suitability for a particular application. In using this guide, therefore, designers should cast their net as wide as possible and should consider all likely candidates when looking for a suitable audio IC for their application.
Integrated power
A major feature of our latest range is the high degree of functional power integrated within each package. A functional power that dramatically reduces the peripheral component count of finished equipment, leading to: · lower system development costs · smaller, more compact circuitry · far fewer production problems · significantly lower production costs.
1-2
Audio Amplifier ICs
PRODUCT SURVEY IN APPLICATION SEQUENCE
2
PRODUCT SURVEY
Audio Amplifier ICs
2-1
PRODUCT SURVEY IN APPLICATION SEQUENCE For portable radio/audio equipment
Type No. TDA1011 TDA1015 TDA1015T TDA1016 TDA1308T TDA7050(T) TDA7052/ TDA7053 TDA7052A(AT)/ TDA7052B(BT) TDA7053A(AT) TDA7056/ TDA7057Q TDA7056A/ TDA7056B TDA7057AQ TDA8541(T) TDA8542(T) TDA8543(T) TDA8547(T) TDA8551(T) TDA8558(T) TDA8559(T) RMS power (W) 6.5 4 0.5 2 2 × 0.06 (d = 0.1%) [0.15]/2 × 0.075 1 2×1 1(0.5) 2 × 1(2 × 0.5) 3 2×3 5 2×5 1 2×1 2 2×1 1 0.125 0.035 Supply (V) 3.6 to 24 3.6 to 18 3.6 to 12 3.6 to 15 3 to 7 1.6 to 6 3 to 18 4.5 to 18 4.5 to 18 3 to 18 4.5 to 18 4.5 to 18 2.2 to 18 2.2 to 18 2.2 to 18 2.2 to 18 2.7 to 6 1.8 to 18 1.8 to 30 Package SIL9MP SIL9MP SO8 DIP16 SO8 DIP8, SO8 DIP8 DIP8, SO8 DIP16, SO16 SIL9MP SIL13P SIL9MP SIL13P DIP8, SO8 DIP16, SO16L DIP16, SO16 DIP16, SO16L DIP8, SO8 DIP8, SO8 DIP16, SO16 Remarks Separate pre/power amplifiers Separate pre/power amplifiers Separate pre/power amplifiers Record/playback + ALC Stereo headphone driver No peripheral components No peripheral components No peripheral components DC volume control; 36 dB gain TDA7052A(AT) with 40 dB gain DC volume control; 40 dB gain No peripheral components No peripheral components DC volume control; 36 dB gain TDA7056A with 40 dB gain DC volume control; 40 dB gain Few peripheral components Few peripheral components Few peripheral components Standby per channel Digital volume control Power saving muting facility Stereo headphone amplifier Page 3-2 3-2 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18
2
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in square brackets refer to performance in BTL configuration.
2-2
Audio Amplifier ICs
PRODUCT SURVEY IN APPLICATION SEQUENCE For car radios/power boosters
Type No. TDA1010A/ TDA1020 TDA1510AQ/ TDA1515BQ TDA1516BQ/ TDA1516CQ/ TDA1518BQ TDA1517(P)/ TDA1519 TDA1519A/ TDA1519B TDA1552Q/ TDA1553Q/ TDA1553CQ/ TDA1557Q TDA1554Q/ TDA1555Q/ TDA1558Q TDA1556Q TDA1560Q TDA1561Q TDA8560Q/ TDA8563Q/ TDA8563AQ TDA8561Q/ TDA8564Q TDA8562Q/ TDA8565Q TDA8566Q TDA8567Q/ TDA8568Q/ TDA8569Q TDA8574(T) TDA8576T TDA8577/ TDA8578(T)/ TDA8579(T) RMS power (W) 3.4 to 12 2 × 12[1 × 24] 2 × 12[1 × 24] Supply (V) 6 to 24 6 to 18 8.5 to 18 Package SIL9MP SIL13P SIL13P Remarks Separate pre/power amplifiers + load dump prot., standby, HF limit 1-end/BTL, 26 - 50[32 - 56] dB gain TDA1510AQ with LS protection 2 × 1-end/1 × BTL, 20[26] dB gain TDA1516BQ but BTL only TDA1516BQ with 40[46] dB gain 20 dB gain TDA1517 with 40 dB gain 2 × 1-end/1 × BTL, 40[46] dB gain Dual BTL amplifiers, [26] dB gain TDA1552Q with LS protection TDA1553Q with CMOS mode switch TDA1553Q with [46] dB gain 1-end/BTL, 20[26] dB gain TDA1554Q with distortion detector TDA1554Q with 40[46] dB gain Dual BTL, diff. inputs, [26] dB gain BTL class-H amplifier, [30] dB gain Automatic switching to high-power mode when needed Dual BTL amplifiers. [40] dB gain TDA8560Q with [26] dB gain TDA8563Q with 2.2% THD (10% with TDA8563Q) 4 × 1-end/dual BTL, 20[26] dB gain TDA8561Q with 40[46] dB gain 4 × 1-end amplifier, 20 dB gain TDA8562Q with 40 dB gain Differential inputs Quad BTL amplifier, 4 load, [26] dB gain TDA8567Q with [40] dB gain TDA8567Q driving 2 load Class H high output level Class H high output level Completely separated inputs Completely separated inputs Inverting inputs linked Page 4-2 4-3 4-4
2
2×6 2 × 11[1 × 22] 2 × 6[1 × 12] [2 × 22]
8.5 to 18 8.5 to 17.5 8.5 to 18 8.5 to 18
SIL9MP, DIP18 SIL9P SIL9MP SIL13P
4-5 4-6 4-7
4 × 11[2 × 22]
8.5 to 18
SIL17P
4-8
[2 × 22] [40] 2 × 23 [2 × 40]
8.5 to 18 8 to 18 6 to 18 8.5 to 18
SIL17P SIL17P DBS13P SIL13P
4-9 4-10 4-11 4-12
4 × 12[2 × 24] 4 × 12 2 × 25 4 × 25
8.5 to 18 8.5 to 18 8.5 to 18 8.5 to 18
SIL17P SIL17P DBS17P DBS23P
4-13 4-14 4-15 4-16
dual line driver dual line driver dual line driver
6 to 12 6 to 12 5 to 18
DIP16, SO16 SO16 SIL9MP DIP16, SO16 DIP8, SO8
4-17 4-18 4-19
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in square brackets refer to performance in BTL configuration.
Audio Amplifier ICs
2-3
PRODUCT SURVEY IN APPLICATION SEQUENCE For mains-powered systems including hi-fi and TV sound
Type No. TDA1013B TDA1514A TDA1521A/ TDA2615 TDA1521(Q)/ TDA2616(Q) TDA2611A TDA2613/ TDA2614 RMS power (W) 4 to 10 50 (d = 0.1%) 2 × 6 (d = 0.5%) 2 × 12 (d = 0.5%) 4 to 10 6 (d = 0.5%) Supply (V) 10 to 40 15 to 60 15 to 42 15 to 42 6 to 35 15 to 42 Package SIL9MP SIL9P SIL9MP SIL9P SIL9MP SIL9MP Remarks DC volume control Super hi-fi, 20 - 46 dB gain Automatic mute; hi-fi TDA1521A with extra mute pin Automatic mute; hi-fi TDA1521(Q) with extra mute pin Adjustable input impedance Automatic mute; hi-fi TDA2613 with extra mute pin Page 5-2 5-3/4 5-5 5-5 5-6 5-6
2
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in square brackets refer to performance in BTL configuration.
2-4
Audio Amplifier ICs
PRODUCT SURVEY IN POWER OUTPUT SEQUENCE Very low power (less than 1 W)
Type No. TDA8574(T) TDA8576T TDA8577 TDA8578(T) TDA8579(T) TDA8559(T) TDA1308T TDA7050(T) TDA1015T RMS power (W) dual line driver dual line driver dual line driver dual line driver dual line driver 0.035 2 × 0.06 (d = 0.1%) [0.15]/2 × 0.075 0.5 Supply (V) 6 to 12 6 to 12 5 to 18 5 to 18 5 to 18 1.8 to 30 3 to 7 1.6 to 6 3.6 to 12 Package DIP16, SO16 SO16 SIL9MP DIP16, SO16 DIP8, SO8 DIP16, SO16 SO8 DIP8, SO8 SO8 Remarks Class H high output level Class H high output level Completely separated inputs Completely separated inputs Inverting inputs linked Stereo headphone amplifier Stereo headphone driver No peripheral components Separate pre/power amplifiers Application c, m c, m c, m c, m c, m p p, c, m p p Page 4-17 4-18 4-19 4-19 4-19 3-18 3-4 3-5 3-2
2
Low power (1 W to 5 W)
Type No. TDA8558(T) TDA7052A(AT)/ TDA7052B(BT) TDA7052/ TDA7053 TDA8541(T) TDA8551(T) TDA8542(T) TDA7053A(AT) TDA8543(T) TDA8547(T) TDA1016 TDA7056/ TDA7057Q TDA1015 TDA7057AQ TDA7056A/ TDA7056B RMS power (W) 0.125 1(0.5) 1 2×1 1 1 2×1 2 × 1(2 × 0.5) 2 2×1 2 3 2×3 4 2×5 5 Supply (V) 1.8 to 18 4.5 to 18 3 to 18 2.2 to 18 2.7 to 6 2.2 to 18 4.5 to 18 2.2 to 18 2.2 to 18 3.6 to 15 3 to 18 3.6 to 18 4.5 to 18 4.5 to 18 Package DIP8, SO8 DIP8, SO8 DIP8 DIP16 DIP8, SO8 DIP8, SO8 DIP16, SO16L DIP16, SO16 DIP16, SO16 DIP16, SO16L DIP16 SIL9MP SIL13P SIL9MP SIL13P SIL9MP Remarks Power saving muting facility DC volume control; 36 dB gain TDA7052A(AT) with 40 dB gain No peripheral components No peripheral components Few peripheral components Digital volume control Few peripheral components DC volume control; 40 dB gain Few peripheral components Standby per channel Record/playback + ALC No peripheral components No peripheral components Separate pre/power amplifiers DC volume control; 40 dB gain DC volume control; 36 dB gain TDA7056A with 40 dB gain Application Page p, m 3-17 p, m 3-7 p, m p, m p, m p, m p, m p, m p, m p, m p, m p, m p, m p, m 3-6 3-12 3-16 3-13 3-8 3-14 3-15 3-3 3-9 3-2 3-11 3-10
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in square brackets refer to performance in BTL configuration. Application areas: c = car radios/power boosters, m = mains-powered equipment, p = portable radio/audio equipment.
Audio Amplifier ICs
2-5
PRODUCT SURVEY IN POWER OUTPUT SEQUENCE Medium power (6 W to 12 W)
Type No. TDA1010A/ TDA1020 TDA1013B TDA2611A TDA2613/ TDA2614 TDA1011 TDA1517(P)/ TDA1519 TDA1521A/ TDA2615 TDA1521(Q)/ TDA2616(Q) RMS power (W) 3.4 to 12 4 to 10 4 to 10 6 (d = 0.5%) 6.5 2×6 2 × 6 (d = 0.5%) 2 × 12 (d = 0.5%) Supply (V) 6 to 24 10 to 40 6 to 35 15 to 42 3.6 to 24 6 to 18 15 to 42 15 to 42 Package SIL9MP SIL9MP SIL9MP SIL9MP SIL9MP SIL9MP, DIP18 SIL9MP SIL9P Remarks Separate pre/power amplifiers + load dump prot., standby, HF limit DC volume control Adjustable input impedance Automatic mute; hi-fi TDA2613 with extra mute pin Separate pre/power amplifiers 20 dB gain TDA1517 with 40 dB gain Automatic mute; hi-fi TDA1521A with extra mute pin Automatic mute; hi-fi TDA1521(Q) with extra mute pin Application Page c, m 4-2 m m m p, m c, m m m 5-2 5-6 5-6 3-2 4-5 5-5 5-5
2
High power (more than 12 W)
Type No. TDA1519A/ TDA1519B TDA1554Q/ TDA1555Q/ TDA1558Q TDA1510AQ/ TDA1515BQ TDA1516BQ/ TDA1516CQ/ TDA1518BQ TDA8562Q/ TDA8565Q TDA8561Q/ TDA8564Q TDA1552Q/ TDA1553Q/ TDA1553CQ/ TDA1557Q TDA1556Q TDA1561Q TDA8566Q TDA8567Q/ TDA8568Q/ TDA8569Q TDA1560Q TDA8560Q/ TDA8563Q/ TDA8563AQ TDA1514A RMS power (W) 2 × 11[1 × 22] 2 × 6[1 × 12] 4 × 11[2 × 22] Supply (V) 8.5 to 17.5 8.5 to 18 8.5 to 18 Package SIL9P SIL9MP SIL17P Remarks 2 × 1-end/1 × BTL, 40[46] dB gain Application Page c, m 4-6 4-8
2 × 12[1 × 24] 2 × 12[1 × 24]
8.5 to 18 8.5 to 18
SIL13P SIL13P
4 × 12 4 × 12[2 × 24] [2 × 22]
8.5 to 18 8.5 to 18 8.5 to 18
SIL17P SIL17P SIL13P
[2 × 22] 2 × 23 2 × 25 4 × 25
8.5 to 18 6 to 18 8.5 to 18 8.5 to 18
SIL17P DBS13P DBS17P DBS23P
[40] [2 × 40]
8 to 18 8.5 to 18
SIL17P SIL13P
50 (d = 0.1%)
15 to 60
SIL9P
1-end/BTL, 20[26] dB gain c TDA1554Q with distortion detector TDA1554Q with 40[46] dB gain 1-end/BTL, 26 - 50[32 - 56] dB gain c TDA1510AQ with LS protection 2 × 1-end/1 × BTL, 20[26] dB gain c TDA1516BQ but BTL only TDA1516BQ with 40[46] dB gain 4 × 1-end amplifier, 20 dB gain c TDA8562Q with 40 dB gain 4 × 1-end/dual BTL, 20[26] dB gain c TDA8561Q with 40[46] dB gain Dual BTL amplifiers, [26] dB gain c TDA1552Q with LS protection TDA1553Q with CMOS mode switch TDA1553Q with [46] dB gain Dual BTL, diff. inputs, [26] dB gain c Automatic switching to highc, m power mode Diagnostic outputs c Quad BTL amplifier, 4 load, [26] dB gain c TDA8567Q with [40] dB gain c TDA8567Q driving 2 loads c BTL class-H amplifier, [30] dB gain c, m Dual BTL amplifiers. [40] dB gain c TDA8560Q with [26] dB gain TDA8563Q with 2.2% THD Super hi-fi, 20 - 46 dB gain m
4-3 4-4
4-14 4-13 4-7
4-9 4-11 4-15 4-16 4-16 4-16 4-10 4-12
5-3/4
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in square brackets refer to performance in BTL configuration. Application areas: c = car radios/power boosters, m = mains-powered equipment, p = portable radio/audio equipment.
2-6
Audio Amplifier ICs
PORTABLE RADIO/AUDIO EQUIPMENT
3
PORTABLE RADIO/ AUDIO EQUIPMENT
Audio Amplifier ICs
3-1
AUDIO AMPLIFIER ICS TDA1011/TDA1015 Preamplifier plus 6.5 W/4 W power amplifier
s s s
PORTABLE RADIO/AUDIO EQUIPMENT
POWER OUTPUT AT d tot = 10% power output (W) with bootstrapping 1 2.3 4.2 *6.5 without bootstrapping 3 supply voltage (V) 6 9 12 16 12 load impedance () 4 4 4 4 4
3
s
s s s s s
Separate preamplifier and power amplifier Thermal protection High input impedance (greater than 100 k) Low current drain (typically 14 mA with a 12 V supply) Limits RF noise. Minimum number of external components Simple and low cost heatsinking No switch-on/switch-off clicks Output noise diminishes with reducing volume
* TDA1011
1 µF 330 k 5 1 µF input 3 220 nF 4 100 µF POWER AMP. 2 680 µF 100 nF 10 µF VP
2
TDA1011/ TDA1015
PREAMP.
These ICs are primarily for battery-powered portable recorders and radios, the TDA1011 offering an output power of 6.5 W and the TDA1015 and output power of 4 W. However, their wide supply voltage ranges (TDA1011: 3.6 to 24 V, TDA1015: 3.6 to 18 V) mean they are also suitable for mains powered equipment. The ICs come in a 9-pin medium-power plastic SIL package and are pin compatible with each other.
9
7 5.6 k
6
1
4.7 1.8 nF
MSB422
100 pF
100 nF
TDA1015T 500 mW amplifier
s s s s
POWER OUTPUT AT d tot = 10% power output (mW) 300 500 500 supply voltage (V) 6 9 12 load impedance () 8 16 32
Separate preamplifier and power amplifier Thermal protection High input impedance (greater than 100 k) Low current drain (typically 14 mA with a 12 V supply) Limits RF noise Few peripheral components
s s
VP 6 0.1 µF 5
TDA1015T
1 PREAMP. POWER AMP. 4 220 µF
This amplifier is for portable and mains-powered equipment. It delivers up to 500 mW into 32 and has a supply voltage range from 3.6 V up to 12 V. It comes in an 8-pin SO package for surface mounting in compact circuitry such as mobile radios and telecom equipment.
input
22 nF 2 8 7 3 4.7
0.1 µF
MSB417
3-2
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA1016 2 W power and record/playback preamplifier
s
PORTABLE RADIO/AUDIO EQUIPMENT
s
s s s s
Separate record/playback preamplifier and power amplifier Incorporates ALC (automatic level control) for recording Voltage stabilization (2.6 V) Short-circuit protection Thermal protection Standby switching facility to minimize current drain
3
This amplifier includes an ALC (automatic level control) circuit and is designed specifically for recorders and radio recorders. With an operating voltage range from 3.6 V to 15 V, it's ideal for a wide range of both portable and mains-powered equipment. Two of these ICs can be used for stereo. The IC comes in a 16-pin plastic DIP with internal heat spreader.
POWER OUTPUT AT d tot = 10% (with bootstrapping) power output (W) 2 supply voltage (V) 9 load impedance () 4
stand-by switch 2.2 M 22 µF 22 µF 10 k recordinput 1 µF 2.2 nF 270 k 180 k 8 PREAMP. 9 82 k 5 7 ALC STAB 6 47 µF 4 3 2 100 µF POWER AMP. 1 100 nF 11 10 12 13 22 µF 160 P 3.3 k 470 pF R 22 k 56 24 k 5.1 k 10 nF 82 k 4.7 k 220 pF 14 15 16 2.7 10 k 100 220 nF nF VP
R P
470 µF
TDA1016
playback input
4
100 k 22 µF 10 k 68 k 22 nF
1 µF 100 k
220 pF 560 pF
MSB421
10 nF
Audio Amplifier ICs
3-3
AUDIO AMPLIFIER ICS TDA1308T 60 mW stereo headphone amplifier
s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
Wide temperature range No switch-on/off clicks Excellent power supply ripple rejection Low current drain (typically 3 mA with a 5 V supply) Short-circuit resistant 110 dB signal-to-noise ratio 5 V/µs slew rate at unity gain Large output voltage swing
3
s s s s
This is a class-AB stereo driver for delivering up to 60 mW into 32 headphones. It is fabricated in a 1 µm CMOS process and is intended primarily for portable digital audio applications. It has a supply voltage range from 3 V to 7 V. It comes an 8-pin SO package for surface mounting.
POWER OUTPUT AT d tot = 10% power output (mW) 60 supply voltage (V) 5 load impedance () 32
VP 100 µF 100 nF 3.9 k 1 nF 100 µF
10 k
1 input 1 V REF (typ. 2.5 V) input 2 2 3
8
TDA1308T
5 6 7 4
headphones
1 nF 10 k 3.9 k 100 µF
MLB701
3-4
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA7050(T) 150 mW BTL or 2 × 75 mW low-voltage amplifier
s
PORTABLE RADIO/AUDIO EQUIPMENT
s
s
s
Requires no external components in BTL configuration Operates with battery supplies from 6 V down to 1.6 V Very low quiescent current (typically 3.2 mA with 3 V supply) Closed-loop voltage gain fixed at 26 dB in the stereo configuration or 32 dB in the BTL configuration (floating differential input, 3 V supply and 32 load)
3
This low-voltage amplifier is for portable mono (BTL) or stereo apparatus with headphones. It comes in an 8-pin plastic DIP (TDA7050), or in an 8-pin small outline (SO) plastic package for surface mounting (TDA7050T).
POWER OUTPUT AT d tot = 10% power output (mW) mono BTL 150 140 stereo 2 × 75 2 × 35 supply voltage (V) 4.5 3 4.5 3 load impedance () 64 32 32 32
VP 100 nF left channel input 22 k 2 1 8 input 7 47 µF right channel input 22 k 22 k 1 2 8 7 100 nF VP
TDA7050(T)
3 4 6 47 µF
TDA7050(T)
4 3 5
MSB405 MSA612
6
TDA7050(T) in single-ended stereo configuration
TDA7050(T) in BTL mono configuration
Audio Amplifier ICs
3-5
AUDIO AMPLIFIER ICS TDA7052/TDA7053 1 W/2 × 1 W BTL amplifiers
s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
3
s s s s
No external components required Excellent overall stability Output protected against short-circuit No external heatsink required Low power consumption No switch-on or switch-off clicks Supply voltage range of 3 V to 18 V Fixed closed-loop voltage gain of 39 dB (6 V supply, 8 load)
The proprietary circuit design of these amplifiers makes use of the bridge-tied load (BTL) principle to achieve low-voltage operation without sacrifice of output power. They are therefore primarily intended for battery-powered portable recorders and radios. However, their wide supply voltage range (3 V to 18 V) also makes them suitable for TV. The TDA7052 comes in an 8-pin plastic DIP and is pincompatible with half of the TDA7053 which is in a 16-pin plastic DIP.
POWER OUTPUT AT d tot = 10% power output (W) TDA7052 1 2 TDA7053 2×1 2×2 supply voltage (V) 6 11 6 11 load impedance () 8 25 8 25
VP 5 100 nF 220 µF
TDA7053
VP 1 100 nF 220 µF 5 k 5 2 3 8 signal ground 6 power ground 9 signal ground 2 10 power ground 1 14 power ground 2
MSA611 MSB420
input 1 2 1
16
TDA7052
input
13 signal ground 1
5 k
input 2 6 7
12
5 k
TDA7053 in BTL mono configuration
TDA7053 in BTL stereo configuration
3-6
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA7052A(AT)/TDA7052B(BT) 1 W/0.5 W BTL amplifiers with DC volume control
s s s
PORTABLE RADIO/AUDIO EQUIPMENT
No external components required Excellent overall stability Output protected against short-circuit to Vp, ground or across load No external heatsink required Low power consumption Thermal protection Low HF radiation All pins ESD protected No switch-on/switch-off clicks Supply voltage range of 4.5 V to 18 V DC volume control Mute facility
portable recorders, radios and telephones, their wide supply voltage range (4.5 V to 18 V) also makes them suitable for multimedia and TV applications. The amplifiers have built-in DC volume control with a logarithmic characteristic providing control over a typical range of 80 dB (73 dB B versions). When the DC control voltage drops below 0.3 V (0.4 V B versions), the amplifier is muted. Except for pin 4 (DC volume control), the amplifiers are pin-compatible with the TDA7052. They come in an 8-pin plastic DIP (TDA7052A/7052B) or in an 8-pin small outline (SO) plastic package for surface mounting (TDA7052AT/TDA7052BT).
s s s s s s s s s
3
The proprietary circuit design of these amplifiers makes use of the bridge-tied load (BTL) principle to provide low-voltage operation without sacrifice of output power. They have fixed voltage gain of 36 dB for the A versions, and 40 dB for the B versions. Although they are primarily for battery-powered
POWER OUTPUT AT d tot = 10% power supply output voltage (W) (V) TDA7052A/TDA7052B 1 6 2 12 TDA7052AT/TDA7052BT 0.5 6 load impedance () 8 32 16
VP 100 nF 220 µF
1 n.c. 7
TDA7052A/B TDA7052AT/BT
input 0.47 µF 2 4
5
8
STABILIZER Vref DC volume control
TEMPERATURE PROTECTION
3
6
MBC281
ground
Audio Amplifier ICs
3-7
AUDIO AMPLIFIER ICS TDA7053A/TDA7053AT 2 × 1 W/2 × 0.5 W BTL amplifiers with DC volume control
s s s
PORTABLE RADIO/AUDIO EQUIPMENT
No external components required Excellent overall stability Output protected against short-circuit to Vp, ground or across load No external heatsink required Low power consumption. Thermal protection Low HF radiation All pins ESD protected No switch-on/switch-off clicks Supply voltage range of 4.5 V to 18 V DC volume control Mute facility
marily for battery-powered portable recorders, radios and telephones, their wide supply voltage range (4.5 V to 18 V) also makes them suitable for multimedia and TV applications. The amplifiers have built-in DC volume control with a logarithmic characteristic providing control over a typical range of 73 dB. When the DC control voltage drops below 0.4 V, the amplifier is muted. They come in a 16-pin plastic DIP (TDA7053A) or in a 16-pin small outline (SO) plastic package for surface mounting (TDA7053AT).
3
s s s s s s s s s
POWER OUTPUT AT d tot = 10%
These amplifiers are stereo versions of the TDA7052B/ TDA7052BT. They use the same proprietary circuit design which makes use of the bridge-tied load (BTL) principle to provide low-voltage operation without sacrifice of output power. They have fixed voltage gain of 40 dB. Although they are pri-
power output (W) TDA7053A 2×1 2×2 TDA7053AT 2 × 0.5
supply voltage (V) 6 12 6
load impedance () 8 32 16
VP 100 nF 220 µF
0.47 µF input 1 DC volume control 1
4 2
TDA7053A TDA7053AT
5 16
13
Vref
STABILIZER
TEMPERATURE PROTECTION
0.47 µF input 2 DC volume control 2
6 8
12
9
7
14
10
MSA718 - 2
ground
3-8
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA7056/TDA7057Q 3 W/2 × 3 W BTL amplifiers
s s s s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
No external components required Excellent overall stability Output protected against short-circuit Low power consumption No switch-on or switch-off clicks Supply voltage range of 3 V to 18 V Fixed closed-loop voltage gain of 39 dB (11 V supply, 16 load)
3
These BTL amplifiers are primarily for battery-powered portables. However, their wide supply voltage range (3 V to 18 V) also makes them suitable for mains-powered applications such as TV. The TDA7056 comes in a 9-pin plastic SIL medium-power package. The TDA7057Q comes in a 13-pin plastic SIL power package with the pins bent to DIL format.
POWER OUTPUT AT d tot = 10% power output (W) TDA7056 3 TDA7057Q 2×3 supply voltage (V) 11 load impedance () 16
11
16
VP 3 100 nF 220 µF
TDA7057Q
VP 2 100 nF 220 µF input 1 2 1 6 3 4 8 signal ground 7 power ground signal ground 2 9 power ground 1 12 power ground 2
MSB418 MSB419
13
5 k
TDA7056
input signal ground 1
11
5 k
input 2 4 5
10
5 k
8
TDA7057Q in BTL configuration
TDA7057Q in BTL stereo configuration
Audio Amplifier ICs
3-9
AUDIO AMPLIFIER ICS TDA7056A/TDA7056B 5 W BTL amplifiers with DC volume control
s s s
PORTABLE RADIO/AUDIO EQUIPMENT
No external components required Excellent overall stability Output protected against short-circuit to Vp, ground or across load Low power consumption No switch-on/switch-off clicks DC volume control Mute mode Thermal protection Low HF radiation All pins ESD protected
POWER OUTPUT AT d tot = 10% power output (W) Both ICs 3.5 TDA7056A 5.0 TDA7056B 5.0 supply voltage (V) 12 load impedance () 16
3
s s s s s s s
These BTL amplifiers are primarily for battery-powered portables. However, their wide supply voltage range (4.5 V to 18 V) also makes them suitable for mains-powered applications such as multimedia and TV. They have fixed voltage gain of 36 dB for the A version, and 40 dB for the B version. The amplifiers have built-in DC volume control with a logarithmic characteristic providing control over a typical range of 80 dB (73 dB B version). When the DC control voltage drops below 0.3 V (0.4 V B version), the amplifier is muted. Both ICs come in a 9-pin plastic SIL package.
12
8
12
8
VP 100 nF 220 µF
2 n.c. n.c. input 0.47 µF 1 9
TDA7056A TDA7056B
6
3 5
8
STABILIZER Vref DC volume control
TEMPERATURE PROTECTION
4
7
MBC280
ground
3-10
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA7057AQ 2 × 5 W BTL amplifier with DC volume control
s s s
PORTABLE RADIO/AUDIO EQUIPMENT
No external components required Excellent overall stability Output protected against short-circuit to Vp, ground or across load Low power consumption No switch-on/switch-off clicks DC volume control Mute mode Thermal protection Low HF radiation All pins ESD protected
The amplifier has built-in DC volume control with a logarithmic characteristic providing control over a typical range of 73 dB. When the DC control voltage drops below 0.4 V, the amplifier is muted. The IC comes in a 13-pin plastic SIL package with the leads bent to DIL format.
s s s s s s s
3
This BTL amplifier is a stereo version of the TDA7056B. Although primarily for battery-powered portables, its wide supply voltage range (4.5 V to 18 V) also makes them suitable for mains-powered applications such as multimedia and TV. It has a fixed voltage gain of 40 dB.
POWER OUTPUT AT d tot = 10% power output (W) 2 × 3.5 2 × 5.0 supply voltage (V) 12 12 load impedance () 16 8
(1)
VP 220 µF
100 nF
4 0.47 µF input 1 DC volume control 1
TDA7057AQ
3 1 13
11
V ref
STABILIZER
TEMPERATURE PROTECTION
0.47 µF input 2 DC volume control 2
5 7
10
8 not connected 2 6 12 9
MSA715 - 1
ground
Audio Amplifier ICs
3-11
AUDIO AMPLIFIER ICS TDA8541/TDA8541T 1 W BTL amplifiers
s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
Few external components required Low saturation voltage of output stage Gain settable with external resistors Standby mode controllable by CMOS-compatible levels Low standby current No switch-on/switch-off clicks High supply-voltage ripple rejection Thermal protection Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
3
s s s s s
s
These amplifiers make use of the bridge-tied load (BTL) principle to achieve low-voltage operation without sacrifice of output power. They are therefore primarily for battery-powered applications such as portable recorders and radios and cellular telephones. However, their wide supply voltage range (2.2 V to 18 V) also makes them suitable for mains powered applications such as multimedia PCs. The amplifiers also feature a standby/mute facility to avoid switch-on/switch-off clicks. They come in an 8-pin plastic DIP (TDA8541) or in an 8-pin small outline (SO) plastic package for surface mounting (TDA8541T).
POWER OUTPUT AT d tot = 10% power output (W) 1 supply voltage (V) 5 load impedance () 8
-
IN- IN+ VCC 4 3 6
TDA8541
5 OUT-
- +
R R
20 k 2 20 k 1
- - +
8
OUT+
SVR
MODE
STANDBY/MUTE LOGIC 7 GND
MGB972
3-12
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA8542/TDA8542T 2 × 1 W BTL amplifiers
s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
s s s s s
s
Few external components required Low saturation voltage of output stage Gain settable with external resistors Standby mode controllable by CMOS-compatible levels Low standby current No switch-on/switch-off clicks High supply-voltage ripple rejection Thermal protection Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
These amplifiers are stereo versions of the TDA8541/ TDA8541T. They are primarily for battery-powered applications such as portable recorders and radios and cellular telephones. However, their wide supply voltage range (2.2 V to 18 V) also makes them suitable for mains powered applications such as multimedia PCs. The amplifiers also feature a standby/ mute facility to avoid switch-on/switch-off clicks. Besides audio applications, they are also suitable for use as electric motor drivers in, for example, CD servo systems. The amplifiers come in a 16-pin plastic DIP (TDA8542) or in a 16-pin small outline (SO) plastic package for surface mounting (TDA8542T).
POWER OUTPUT AT d tot = 10% power output (W) 2×1
VCCL VCCR 16 9
3
supply voltage (V) 5
load impedance () 8
-
INL- INL+ 14 13
- +
R VCCL R
15
OUTL-
20 k
- - +
2
OUTL+
20 k
STANDBY/MUTE LOGIC
-
INR- INR+ 11 12
TDA8542
10 OUTR-
- +
R VCCR R
20 k 4 20 k 3 5
- - +
7
OUTR+
SVR
MODE BTL/SE
STANDBY/MUTE LOGIC 1 LGND 8
MGB975
RGND
Audio Amplifier ICs
3-13
AUDIO AMPLIFIER ICS TDA8543/TDA8543T 2 W BTL amplifiers
s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
Few external components required Low saturation voltage of output stage Gain settable with external resistors Standby mode controllable by CMOS-compatible levels Low standby current No switch-on/switch-off clicks High supply-voltage ripple rejection Thermal protection Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
3
s s s s s
s
These BTL amplifiers are primarily for battery-powered applications such as portable recorders and radios and cellular telephones. However, their wide supply voltage range (2.2 V to 18 V) also makes them suitable for mains powered applications such as multimedia PCs. The amplifiers also feature a standby/ mute facility to avoid switch-on/switch-off clicks. They come in a 16-pin plastic DIP (TDA8543) or in an 16-pin small outline (SO) plastic package for surface mounting (TDA8543T).
POWER OUTPUT AT d tot = 10% power output (W) 1 2 1.4 2 1.3 supply voltage (V) 5 7.5 7.5 9 9 load impedance () 8 8 16 16 25
VCC 12 IN- IN+ 6 5 11 OUT-
VCC
R R
20 k SVR 4 20 k
14
OUT+
TDA8543
MODE
3
STANDBY/MUTE LOGIC 13 GND
MSC249
3-14
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA8547/TDA8547T 2 × 1 W BTL amplifiers with independent channel standby selection
s s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
Independent standby selection of output channels Few external components required Low saturation voltage of output stage Gain settable with external resistors Standby mode controllable by CMOS-compatible levels Low standby current No switch-on/switch-off clicks High supply-voltage ripple rejection Thermal protection Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
s s s s s
These BTL stereo amplifiers incorporate standby/mute logic that allows either one of the output channels to be switched into a standby condition. This feature can be used, for example, for loudspeaker selection. The amplifiers are primarily for batterypowered applications such as portable recorders and radios and cellular telephones. However, their wide supply voltage range (2.2 V to 18 V) also makes them suitable for mains powered applications such as multimedia PCs. The amplifiers come in a 16-pin plastic DIP (TDA8547) or in a 16-pin small outline (SO) plastic package for surface mounting (TDA8547T).
3
s
POWER OUTPUT AT d tot = 10% power output (W) 2×1 supply voltage (V) 5 load impedance () 8
VCC1 VCC2 16 IN1- IN1+ 14 13 R R 9 15 OUT1-
2
OUT1+
STANDBY/MUTE LOGIC
IN2- IN2+
11 12
10
OUT2-
VCC
R R
20 k SVR 4 20 k 3 5 STANDBY/MUTE LOGIC 8 GND2 1
7
OUT2+
TDA8547
MODE SELECT
MSC261
GND1
Audio Amplifier ICs
3-15
AUDIO AMPLIFIER ICS TDA8551/TDA8551T 1 W BTL amplifiers with digital volume control
s
PORTABLE RADIO/AUDIO EQUIPMENT
s
3
s s
One-pin digital volume control (volume setting with up/down pulses) Few external components required Low saturation voltage of output stage Standby mode controllable by CMOS-compatible levels Low standby current No switch-on/switch-off clicks High supply-voltage ripple rejection Thermal protection Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
s s s s s
s
These BTL mono amplifiers feature digital volume control and standby/mute logic. They are primarily for battery-powered applications such as portable recorders/radios and cellular telephones but they are also ideally suited for use in, for example, personal computers. The amplifiers come in an 8-pin plastic DIP (TDA8551) or in an 8-pin small outline (SO) plastic package for surface mounting (TDA8551T).
POWER OUTPUT AT d tot = 10% power output (W) 1 supply voltage (V) 5 load impedance () 8
up/down 1 in 4 VOLUME CONTROL VCC 50 k SVT 3
VCC 6 MASTER 8 OUT+
20 k 5 k
R R
50 k
TDA8551
SLAVE STANDBY/MUTE OPER 2 MODE 7 GND
5
OUT+
MSC262
3-16
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA8558/TDA8558T Low-voltage BTL mono amplifiers
s s s s s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
Operating voltages down to 1.8 V Very low quiescent current Low distortion No external components required Differential inputs Standby mode No switch-on/switch-off clicks Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
3
s
These BTL mono amplifiers operate at voltages from as low as 1.8 V up to a maximum of 18 V. They also consume very little quiescent current. The amplifiers are therefore ideally suited to battery-powered applications (2 × 1.5 V cells) in, for example, cellular telephones and personal audio equipment. Moreover, a dynamic quiescent controller (DQC) feature automatically increases quiescent current at higher frequencies to minimize HF cross-over distortion. The amplifiers also feature a standby/ mute facility to avoid switch-on/switch-off clicks. They come in an 8-pin plastic DIP (TDA8558) or in an 8-pin small outline (SO) plastic package for surface mounting (TDA8558T).
POWER OUTPUT AT d tot = 10% power output (W) 0.125 supply voltage (V) 3 load impedance () 25
VP 8 STANDBY 1 REF VP
MUTE
4
INPUT LOGIC
OA
7
OUT+
2 INPUT 3 VP OA 5 OUT- OA DQC
TDA8558
8 GND
MSC263
Audio Amplifier ICs
3-17
AUDIO AMPLIFIER ICS TDA8559/TDA8559T Low-voltage BTL stereo amplifiers
s s s s
PORTABLE RADIO/AUDIO EQUIPMENT
Operating voltages down to 1.9 V Very low quiescent current Low distortion Few external components required Differential inputs Can be used as a mono amplifier in BTL or stereo single-ended (SE) mode SE mode without need of capacitor in series with the loudspeaker Mute and standby mode No switch-on/switch-off clicks Outputs short-circuit safe to ground, VCC and across load All pins ESD protected
3
s s
battery-powered applications (2 × 1.5 V cells) in, for example, personal audio equipment. They can also be used as a mono amplifier (e.g. in cellular phones) and as a line driver in mainspowered applications without need of any external components. A dynamic quiescent controller (DQC) feature automatically increases quiescent current at higher frequencies to minimize HF cross-over distortion. The amplifiers also feature a standby/ mute facility to avoid switch-on/switch-off clicks. They come in a 16-pin plastic DIP (TDA8559) or in a 16-pin small outline (SO) plastic package for surface mounting (TDA8559T).
s
s s s
POWER OUTPUT AT d tot = 10% power output (W) 0.035 BTL mode 0.140 supply voltage (V) 3 load impedance () 32
s
These BTL stereo amplifiers operate at voltages from as low as 1.9 V up to a maximum of 30 V and they consume very little quiescent current. The amplifiers are therefore ideally suited to
3
25
VP2 15 STANDBY 1 REFERENCE
VP1 16
VP -INV1 INV1 2 3 50 k MUTE MODE -INV2 INV2 7 8 5 6 50 k INPUT LOGIC + - 50 k V/I + - OA DQC 11 + - V/I - + OA
14
OUT1
50 k DQC
OUT2
VP
SVRR
4
12
BUFFER
BUFFER
TDA8559
9,10 n.c. 13
MGD115
GND
3-18
Audio Amplifier ICs
4
CAR RADIOS/ POWER BOOSTERS
Audio Amplifier ICs
4-1
AUDIO AMPLIFIER ICS TDA1010A/TDA1020 Preamplifier plus 3.4 to 12 W power amplifier
s
CAR RADIOS/POWER BOOSTERS
s s s s
Separate preamplifier and power amplifier allows standby switching Low-cost of external components Good ripple rejection Thermal protection Output protected against AC short-circuit to ground Load dump protection allows the circuit to tolerate supply voltages as high as 45 V without damage High frequency limiting beyond the audible range in the pre-amplifier and power amplifier suppresses supply interference and ignition noise Standby switching feature with low current consumption (<1 mA)
4
s
s
POWER OUTPUT AT d tot = 10% power supply load output voltage impedance (W) (V) () without bootstrap 5.5 14.4 4 with bootstrap capacitor (TDA1010A/1020) 3.4 14.4 8 6.2 14.4 4 6.4/12 14.4 2 with additional 220 bootstrap resistor between pins 3 and 4 (TDA1010A only) 9 14.4 2 10 18 2
s
Although these mono amplifiers are primarily for use in car radios, their wide supply voltage range (6 V to 24 V) also makes them attractive for mains-powered radios and tape recorders requiring output powers up to 12 W. They come in a 9-pin plastic SIL medium-power packages for easy mounting.
100 nF 330 k 5 1 µF input
stand-by switch
100 nF
680 µF VP
3
4
100 µF
TDA1010A
8 PREAMP. POWER AMP. 2 1000 µF 100 nF RL 4.7 1 nF
MSB412
9
7 100 nF
6
1
4-2
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA1510AQ/TDA1515BQ 24 W BTL or 2 × 12 W amplifiers
s
CAR RADIOS/POWER BOOSTERS
s
s s s
s s
Low offset voltage at output (<50 mV) important for BTL Externally adjustable voltage gain range of 32 dB to 56 dB in BTL configuration and 26 dB to 50 dB in stereo configuration (14.4 V supply, 4 load) High ripple rejection (50 dB at 1 kHz, Rs = 0 ) Load dump and SOAR protection Protection against AC short-circuit from output to ground Thermal protection Internally limited bandwidth for rejection of HF interference Low standby current (<2 mA) to simplify switching Few external components needed
These class-B output amplifiers can be used in car audio systems to drive loads down to 1.6 . They have externally adjustable voltage gain. They come in 13-pin plastic SIL power packages with the pins bent to DIL format.
4
s s
Additional features of the TDA1515BQ s Low standby current (<100 µA) which allows switching via TTL circuitry s Outputs protected against AC and DC shortcircuit to ground s Loudspeaker protection in BTL configuration s Outputs protected against short-circuit to ground in BTL configuration s Protected against reverse polarity supply voltage
POWER OUTPUT AT d tot = 10% power supply output voltage (W) (V) mono BTL with bootstrap capacitors 24 14.4 stereo with bootstrap capacitors 2×7 14.4 2 × 12 14.4 stereo without bootstrap capacitors 2×6 14.4 load impedance () 4 4 2 4
100 k
100 µF
100 k stand-by switch 22 0.1 µF 12 13 0.1 µF 0.22 µF input 2 1 VP
100 k
47 µF
100 k stand-by switch 22 0.1 µF 12 13 0.22 µF VP 10
3 0.1 µF input 2 1
11
10
TDA1510AQ TDA1515BQ
3
11
TDA1510AQ TDA1515BQ
6 100 µF 100 k 0.1 µF 4.7
5
9 100 µF
8
7 4
(1)
6
5
9
8
7 330 pF
100 k 1 1 mF mF 0.1 µF 4.7
47 µF 100 µF 100 k 4.7 0.1 µF 100 µF 100 k
680
1 k 4.7 µF
1 k 4.7 µF
MSB411
MSB410
(1)
TDA1515B only
2 k
4.7 µF
TA1510AQ/TDA1515BQ in single-ended stereo configuration
TA1510AQ/TDA1515BQ in BTL mono configuration
Audio Amplifier ICs
4-3
AUDIO AMPLIFIER ICS TDA1516BQ/TDA1516CQ/TDA1518BQ 24 W BTL or 2 × 12 W amplifiers
s s
CAR RADIOS/POWER BOOSTERS
s
4
s
s s
No external components in BTL configuration Low offset voltage (100 mV) at output (250 mV for TDA1518BQ) important for BTL Fixed closed-loop voltage gain (14.4 V supply, 4 load) of 26 dB for BTL (TDA1516BQ and TDA1516CQ) and 20 dB for stereo (TDA1516BQ). The figures for the TDA1518BQ are 46 dB (BTL) and 40 dB (stereo) High supply voltage ripple rejection (48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply rail Thermal protection Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 11 and a switch-on current of only 12 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 11 for normal operation is >8.5 V Mute facility with switch-on voltage of 3 V to 6.4 V at pin 11 to eliminate switch-on/switch-off clicks. The supply current in the muted condition is 40 mA
s s
Identical inputs (inverting and non-inverting) Few external components needed in stereo configuration
Like the TDA1510AQ/1515BQ these are car audio class-B power amplifiers but with internally fixed gain for excellent channel balance (within 1 dB). The three types are virtually identical except for their gain. The TDA1516CQ is identical to the TDA1516BQ except that it consumes very little current in short-circuit to ground condition (typically 5.5 mA) and is only suitable for operation in BTL mode. The ICs come in 13-pin plastic SIL power packages with the pins bent to DIL format.
POWER OUTPUT AT d tot = 10% power supply output voltage (W) (V) mono BTL with bootstrapping 24 14.4 mono BTL without bootstrapping 22 14.4 stereo with bootstrapping 2×7 14.4 2 × 12 14.4 stereo without bootstrapping 2×6 14.4 2 × 11 14.4 load impedance () 4 4 4 2 4 2
s s s
s
stand-by switch 100 nF 11 1 60 k 2 5 2 V P 12 2 10 6 to VP input 1 VP 2.2 mF 220 nF 1
stand-by switch 100 nF 11 10 6 to VP 60 k 5 1 mF VP 2 input ref. voltage 8 to VP to VP 220 nF input 2 60 k 13 9 1 mF 12 100 µF VP 2.2 mF
TDA1516BQ/CQ TDA1518BQ
220 nF input 4
TDA1516BQ TDA1518BQ
4
input ref. voltage 8 60 k 9
13
3 signal ground
7 power ground
3 signal ground
7 power ground
MSB259
TDA1516BQ/TDA1516CQ/TDA1518BQ in BTL mono configuration
TDA1516BQ/TDA1518BQ in single-ended stereo configuration
4-4
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA1517(P)/TDA1519 2 × 6 W amplifiers
s
CAR RADIOS/POWER BOOSTERS
s s
s s
s s s s s
Fixed closed-loop voltage gain of typically 20 dB for the TDA1517(P), 40 dB for the TDA1519 (14.4 V supply, 4 load) Excellent channel balance (within 1 dB) High supply voltage ripple rejection (48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply Thermal and SOAR protection Reverse polarity safe Protected against electrostatic discharge Few external components needed Standby feature with switch-on voltage of 0 V to 2 V at pin 8 and a switch-on current of only 12 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 8 for normal operation is >8.5 V Mute facility with switch-on voltage of 3 V to 6.4 V at pin 8 to eliminate switch-on/switch-off clicks. The supply current in the muted condition is 40 mA
The TDA1517 and TDA1519 are stereo power amplifiers developed for use in car audio systems. They are virtually identical except for their gain. The TDA1517 and TDA1519 come in 9-pin plastic SIL medium-power packages and the TDA1517P comes in an 18-pin DIP.
4
s
POWER OUTPUT AT d tot = 10% power output (W) 2×6 supply voltage (V) 14.4 load impedance () 4
stand-by switch 100 µF 100 nF 2200 µF VP
input reference voltage
internal 1/2 V P
TDA1517
220 nF input 1 60 k 60 k 220 nF input 2
MSB261 - 1
1000 µF
1000 µF
Audio Amplifier ICs
4-5
AUDIO AMPLIFIER ICS TDA1519A/TDA1519B 22 W BTL or 2 × 11 W/12 W BTL or 2 × 6 W amplifiers
s s
CAR RADIOS/POWER BOOSTERS
s
s
4
s
s s
No external components in BTL configuration Very few external components in stereo configuration Low offset voltage at output (250 mV) important for BTL Fixed closed-loop voltage gain (14.4 V supply, 4 load) of 46 dB for BTL and 40 dB for stereo High supply voltage ripple rejection (48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply rail Thermal protection Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 8 and a switch-on current of only 12 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 8 for normal operation is >8.5 V
s
s
Mute facility with switch-on voltage of 3.3 V to 6.4 V at pin 8 to eliminate switch-on/switch-off clicks. The supply current in the muted condition is 40 mA Identical inputs (inverting and non-inverting)
These are car audio class-B power amplifiers with internally fixed gain for excellent channel balance (within 1 dB). The two types are virtually identical except for their output power. The TDA1519A comes in a 9-pin power plastic SIL package with or without the pins bent to DIL format. The TDA1519B comes in a 9-pin plastic medium-power SIL package.
s s s
POWER OUTPUT AT d tot = 10% power supply output voltage (W) (V) mono BTL (TDA1519A/1519B) 22/12 14.4 stereo (TDA1519A/1519B) 2 × 11/6 14.4 load impedance () 4 4
stand-by switch 100 nF 8 220 nF input 1 7 VP 2.2 mF 220 nF 4 60 k internal Vref. 60 k 9 6 input 2 220 nF 60 k 9 input 1
stand-by switch 100 nF 8 1 7 VP 2.2 mF
4 60 k internal V ref.
1 mF
6
TDA1519A(B)
1/2 VP 3 2 5
TDA1519A(B)
1/2 VP 3 2 5
MSB260
TDA1519A(B) in BTL mono configuration
TDA1519A(B) in single-ended stereo configuration
4-6
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA1552Q/TDA1553Q/CQ/TDA1557Q 2 × 22 W BTL amplifiers
s s
CAR RADIOS/POWER BOOSTERS
s
s
s s
s
Very few external components Low offset voltage at output (150 mV; 250 mV for the TDA1557Q) important for BTL Fixed closed-loop voltage gain (14.4 V supply, 4 load) of 26 dB (46 dB for the TDA1557Q) High supply voltage ripple rejection (48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply rail Low current consumption in short-circuit to ground condition (typ. 5.5 mA) Thermal protection Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 11 and a switch-on current of only 25 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 11 for normal operation is >8.5 V Mute facility with switch-on voltage of 3.3 V to 6.4 V at pin 11 to eliminate switch-on/switch-off clicks
s
s
TDA1553CQ incorporates mute/standby/normal operation selection with CMOS-compatible switching levels Loudspeaker protection limits voltage across the associated loudspeaker to 1 V or less in the event any of the outputs being short-circuited to ground (TDA1553Q, TDA1553CQ and TDA1557Q)
These are car audio class-B power amplifiers with internally fixed gain for excellent channel balance (within 1 dB). The four types are virtually identical except that the TDA1553Q, TDA1553CQ and TDA1557Q incorporate loudspeaker protection and that the TDA1557Q has a 20 dB higher gain. They come in 13-pin plastic SIL power packages with the pins bent to DIL format.
4
s s s
POWER OUTPUT AT d tot = 10% power output (W) 2 × 22 supply voltage (V) 14.4 load impedance () 4
s
mute/stand-by not connected 12 220 nF input 1 11 3 100 nF 10 VP 2.2 mF 12 220 nF 4 60 k 6 input 1
mute/stand-by 100 nF 11 3 10 VP 2.2 mF
TDA1552Q/TDA1557Q
1 1
TDA1553Q(CQ)
4 60 k 6
signal ground
2
V ref
signal ground
2
V ref
220 nF input 2
13 60 k
220 nF 9 input 2
13 60 k
9
7
7
* connected to Vref on the TDA1557Q
5
8
5
8
MSB257
power ground (substrate)
power ground (substrate)
TDA1552Q/TDA1557Q in BTL stereo configuration
TDA1553Q/TDA1553CQ in BTL stereo configuration
Audio Amplifier ICs
4-7
AUDIO AMPLIFIER ICS TDA1554Q/TDA1555Q/TDA1558Q 2 × 22 W BTL or 4 × 11 W amplifiers
s s
CAR RADIOS/POWER BOOSTERS
Very few external components Low offset voltage at output (100 mV, 250 mV for the TDA1558Q) important for BTL Fixed closed-loop voltage gain (14.4 V supply, 4 load) of 20 dB (26 dB in BTL), 40 dB (46 dB in BTL) for the TDA1558Q High supply voltage ripple rejection (48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply rail Thermal protection Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 14 and a switch-on current of only 12 µA to allow use of an inexpensive-pensive switch. The standby supply current is >100 µA. The voltage at pin 14 for normal operation is >8.5 V Mute facility with switch-on voltage of 3.3 V to 6.4 V at pin 14 to eliminate switch-on/switch-off clicks
mute/stand-by switch distortion detector 15 220 nF input 1 14 5 100 nF 13 VP 2.2 mF
s s
s
Identical inputs (inverting and non-inverting) Distortion detector senses output clipping and for clip distortion of 3.5% it supplies a current of 50 µA typical for reducing the drive via a sound processor or DC volume control (TDA1555Q only)
s
4
s s
These are class-B power amplifiers with internally fixed gain for excellent channel balance (within 1 dB). They are for BTL stereo or quad (front and rear stereo) car audio applications. The three types are virtually identical except that the TDA1555Q incorporates distortion detection, and the TDA1558Q has 20 dB higher gain. They come in 17-pin plastic SIL power packages with the pins bent to DIL format.
POWER OUTPUT AT d tot = 10% power output (W) BTL stereo 2 × 22 quad 4 × 11 4×6 supply voltage (V) 14.4 14.4 14.4 load impedance () 4 2 4
s s s
s
mute/stand-by switch distortion detector 15 220 nF 6 input 1 14 5 100 nF 13 VP 2.2 mF
TDA1554Q/1555Q/1558Q
1 60 k 60 k 2
TDA1554Q/1555Q/1558Q
1 60 k 220 nF input 2 supply 100 ripple µF rejection 220 nF 60 k 2 1 mF 6 1 mF
8
8
supply ripple rejection 220 nF input 2
4
VP /2
V ref
4
V P /2
V ref 1 mF
17 60 k
12
input 3
17 60 k
12
16
60 k
10 input 4
220 nF
16
60 k
10
1 mF
3 signal ground
7
11
9 not connected
* not connected on the TDA1554Q connected to Vref on the TDA1558Q
3 signal ground
7
11
9 not connected
power ground (substrate)
power ground (substrate)
MSB255
TDA1554Q/TDA1555Q/TDA1558Q in BTL stereo configuration
TDA1554Q/TDA1555Q/TDA1558Q in single-ended quad (dual stereo) configuration
4-8
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA1556Q 2 × 22 W BTL amplifier with differential inputs
s s s s
CAR RADIOS/POWER BOOSTERS
Very few external components Differential inputs High CMRR (>64 dB) High supply voltage ripple rejection (48 dB between 100 Hz and 10 kHz, Rs = 0 ) Low offset voltage at output (150 mV) important for BTL Fixed closed-loop voltage gain (14.4 V supply, 4 load) of 26 dB Load dump protection Thermal protection Outputs protected against AC and DC shortcircuit to ground, supply rail or across load Low current consumption in short-circuit to ground condition (5.5 mA) Reverse polarity safe Loudspeaker protection limits voltage across the associated loudspeaker to 1 V or less in the event any of the outputs being short-circuited to ground Standby feature with switch-on voltage of 0 V to 2 V at pin 14 and a switch-on current of only 25 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 14 for normal operation is >8.5 V Mute facility with switch-on voltage of 3.3 V to 6.4 V at pin 14 to eliminate switch-on/switch-off clicks Distortion detector senses output clipping. It provides 50 µA typical for a clip distortion of 3.5% to reduce input drive via a sound processor or DC volume control
s
This is a class-B power amplifier with internally fixed gain for excellent channel balance (within 1 dB). The amplifier has two differential input stages with high Common Mode Ripple Rejection (CMRR) which makes it very attractive for car radio booster applications. The TDA1556Q also incorporates a Dynamic Distortion Detector (DDD) and loudspeaker protection. It comes in a 17-pin plastic SIL power package with the pins bent to DIL format.
s
4
s s s
s
POWER OUTPUT AT d tot = 10% power output (W) 2 × 22 supply voltage (V) 14.4 load impedance () 4
s s
s
DDD
on/mute/stand-by
VP 100 nF 2200 µF
4 220 nF input 1
14
5
13
1 6 60 k
s
60 k 220 nF input 2 n.c. 2
8
s
9
TDA1556Q
n.c. 220 nF input 3 3 16
Vref
15 4.7 µF
10 60 k
60 k 220 nF input 4 17
12
7
11
MBC271
TDA1556Q in BTL stereo configuration
Audio Amplifier ICs
4-9
AUDIO AMPLIFIER ICS TDA1560Q 40 W BTL class-H amplifier
s s s s
CAR RADIOS/POWER BOOSTERS
Few external components Very high output power Low power dissipation when reproducing music Fixed closed-loop voltage gain (14.4 V supply, 8 load) of 30 dB High supply voltage ripple rejection of 55 dB over the frequency range 100 Hz to 10 kHz, Rs = 0 ) Switches to low output power if the heatsink overheats Low crossover distortion No switch-on/off clicks Thermal protection Mode switch for standby (0 to 1.2 V)/mute (2.6 to 3.5 V)/class-B (4.5 to 7 V)/class-H (8.5 V to Vp) operation. Maximum switch current is only 20 µA to allow use of an inexpensive-pensive switch Low offset voltage at the output important for BTL Load dump protection Load short-circuit safe to ground or Vp
s s
Pins protected against ESD Thermal protection
s
Primarily for car audio applications, this IC uses class-H amplifier techniques so that, with a 14.4 V supply and minimal heatsinking, it can deliver 40 W into an 8 load. For the first time, this allows a 4 × 40 W car radio to be assembled in a standard DIN-sized car radio case. Below 10 W the IC acts as a normal BTL amplifier. At higher outputs, the internal supply voltage is doubled by adding the charge stored on external capacitors. This allows the power output to increase to 40 W. The amplifier comes in a 17-pin plastic SIL power package with the pins bent to DIL format.
POWER OUTPUT AT d tot = 10% power output (W) 17 40 supply voltage (V) 14.4 14.4 load impedance () 4 8
s
4
s s s s
s
s s
2 2200 µ F 0.22 µF 100 nF 9
VP 2200 µ F
13 10 k disable TEMPERATURE SENSOR SUPPLY
10
S1
17
TDA1560Q
VP Ck input 150 nF Rex = 100 k Ck 150 nF input () Vref 10 µ F 16 mode select switch 3 15 15 k voltage reference SUPPLY disable 5 2200 µF 8 12 6 INPUT AND FEEDBACK CIRCUIT 0.22 µ F VP 1 150 k 2 POWER STAGE input (+) 1 150 k POWER STAGE LOAD DUMP TEMPERATURE AND CURRENT PROTECTION 11 output 2 (+) diagnostic 14 output 7 output 1 () 1 0.22 µ F
4
0.22 µ F
0.22 µ F 2
ground
MCD333 - 3
4-10
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA1561Q 2 × 23 W high efficiency power amplifier
s
CAR RADIOS/POWER BOOSTERS
Low power dissipation since the amplifier switches from SE mode into BTL mode only when receiving high-amplitude signals High common-mode rejection ratio Mute/standby/BTL-disable switch (mode select pin) Zero-crossing mute Load dump protection Short-circuit safe to ground, Vp and across load Loudspeaker protection Automatically switches to SE mode at excessive crystal temperature Thermal protection
s s s s s s s
4
s
This power amplifier normally operates in low-power singleended mode and switches to high-power BTL mode only when large amplitude signals are received from the preamplifer. The TDA1561Q therefore dissipates only about 55% of the power dissipated by a conventional power amplifier (measured at average maximum music power) which means heatsinks can be smaller. Primarily for car audio applications, the amplifier is also ideal for multimedia systems and active loudspeakers. The TDA1561Q comes in a 13-pin plastic SIL power package with the pins bent to DIL format.
POWER OUTPUT AT d tot = 10% power output (W) 2 × 23 supply voltage (V) 14.4 load impedance () 4
VP 7 MUTE 1
IN1
6 OUT1 5 R OUT1
CIN
12
1/2R
REFERENCE SOURCES MUTE/STANDBY
THERMAL/ SHORT-CIRCUIT PROTECTION
HIGHER TEMPERATURE BTL DISABLE
0.5VP
11
C 11
MODE HVP
3 9 2 OUT2 R 8 OUT2
IN2
13
MUTE 4 GND1 10 GND2
TDA1561Q
MLD214
Audio Amplifier ICs
4-11
AUDIO AMPLIFIER ICS TDA8560Q/TDA8563Q/TDA8563AQ 2 × 40 W BTL amplifiers
s s
CAR RADIOS/POWER BOOSTERS
Very few external components High supply voltage ripple rejection (>50 dB between 100 Hz and 10 kHz, Rs = 0 ) Low offset voltage (150 mV) at output (200 mV for TDA8560Q) important for BTL Fixed closed-loop voltage gain (14.4 V supply, 4 load) of 26 dB (TDA8563Q/TDA8563AQ) or 40 dB (TDA8560Q) Load dump protection Thermal protection Outputs protected against AC and DC shortcircuit to ground, supply rail or across load Low current consumption in short-circuit to ground condition Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 11 and a switch-on current of only 15 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 11 for normal operation is >8.5 V Mute facility with switch-on voltage of 3.3 V to 6.4 V at pin 11 to eliminate switch-on/switch-off clicks Diagnostic facility senses distortion, load shortcircuit and temperature Pins protected against ESD Low thermal resistance
s
s
4
s s s
POWER OUTPUT AT d tot = 10% power output (W) 2 × 21 2 × 25 2 × 35 2 × 40 supply voltage (V) 13.2 14.4 13.2 14.4 load impedance () 4 4 2 2
s
s s
mode switch VP 2200 µF
s
11 470 nF input 1
3
10
100 nF
1 4
s
30 k 6 VP ground (signal) 2
s s
TDA8560Q TDA8563Q
12 reference voltage
10 k diagnostic output
These are class-B power amplifiers with internally-fixed voltage gain for excellent channel balance (within 1 dB). They are primarily for car audio applications. The amplifiers are distinguishable by their closed-loop voltage gain. The gain of the TDA8560Q is 40 dB, and that of the TDA8563Q and TDA8563AQ is 26 dB. A diagnostic facility senses distortion, load short-circuit and temperature. At onset of distortion (10% THD in the TDA8560Q/TDA8663Q, 2.5% THD in the TDA8563AQ) or temperature >150 °C, the diagnostic output signal can be used to reduce the input drive via a sound processor or DC volume control. For load short-circuit or output short-circuit to ground or supply, the outputs are switched-off until the short-circuit is removed. The ampliers come in 13-pin plastic SIL power packages with the pins bent to DIL format.
470 nF input 2
13 9
30 k 7
5
8
MLB666 - 2
power ground (substrate)
4-12
Audio Amplifier ICs
AUDIO AMPLIFIER ICS TDA8561Q/TDA8564Q 2 × 24 W BTL or 4 × 12 W amplifiers
s s
CAR RADIOS/POWER BOOSTERS
s
s s
s
s s s
s
s s
s s
Very few external components Low offset voltage (150 mV) at output (250 mV for TDA8564Q) important for BTL High supply voltage ripple rejection (>48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply rail Low current consumption (40 mA) during any short-circuit condition Thermal protection Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 14 and a switch-on current of only 12 µA to allow use of an inexpensive-pensive switch. The standby supply current is >100 µA. The voltage at pin 14 for normal operation is >8.5 V Mute facility with switch-on voltage of 3.3 V to 6.4 V at pin 14 to eliminate switch-on/switch-off clicks Identical inputs (inverting and non-inverting) Diagnostic facility senses distortion, load shortcircuit and temperature Pins protected against ESD Low thermal resistance
mode switch diagnostic VP 10 k 16 5 13 100 nF 2200 µF
These are class-B power amplifiers with internally-fixed gain for excellent channel balance (within 1 dB). They are for BTL stereo or quad (front and rear stereo) car audio applications. The two types are identical except that the TDA8561Q has a fixed closed-loop voltage gain of 26 dB (BTL)/20 dB (single-ended) whereas that of the TDA8564Q 46 dB (BTL) and 40 dB (single-ended). A diagnostic facility senses distortion, load short-circuit and temperature. At onset of distortion or temperature >150 °C, the diagnostic output signal can be used to reduce the input drive via a sound processor or DC volume control. For load shortcircuit or output short-circuit to ground or supply, the outputs are switched-off until the short-circuit is removed. The amplifiers come in 17-pin plastic SIL power packages with the pins bent to DIL format.
4
POWER OUTPUT AT d tot = 10% power output (W) BTL stereo 2 × 24 quad 4×7 4 × 12 supply voltage (V) 14.4 14.4 14.4 load impedance () 4 4 2
VP 10 k 16 5 13 100 nF 2200 µF
mode switch
14 220 nF
14 220 nF
non- inverting input 1
1
TDA8561Q TDA8564Q
6
non- inverting input 1
1
TDA8561Q TDA8564Q
6 1000 µF
60 k 8 inverting input 2 ground (signal) 3 2 60 k inverting input 2 reference voltage 9 60 k 17 12
not connected
60 k 220 nF 8 3 2 60 k 1000 µF
ground (signal)
supply voltage ripple rejection 220 nF
4
4 supply voltage ripple rejection non-inverting input 4 220 nF 1/2Vp 60 k 17
reference voltage 9
not connected
non-inverting input 4
12 1000 µF 60 k
60 k 10 inverting input 3 15 inverting input 3 220 nF
10 15 1000 µF
7
11
MEA862 - 2
7
11
MEA863 - 2
power ground (substrate)
power ground (substrate)
TDA8561Q/TDA8564Q in BTL stereo configuration left, and in single-ended quad (front and rear stereo) configuration
Audio Amplifier ICs
4-13
AUDIO AMPLIFIER ICS TDA8562Q/TDA8565Q 4 × 12 W single-ended amplifier
s s
CAR RADIOS/POWER BOOSTERS
Very few external components High supply voltage ripple rejection (>48 dB between 100 Hz and 10 kHz, Rs = 0 ) Load dump protection Output protected against AC and DC short-circuit to ground or supply rail Low current consumption (40 mA) during any short-circuit condition Identical inputs Thermal protection Reverse polarity safe Standby feature with switch-on voltage of 0 V to 2 V at pin 8 and a switch-on current of only 12 µA to allow use of an inexpensive switch. The standby supply current is <100 µA. The voltage at pin 8 for normal operation is >8.5 V Mute facility to eliminate switch-on/switch-off clicks Diagnostic facility for sensing distortion, shortcircuit and temperature Pins protected against ESD Low thermal resistance
POWER OUTPUT AT d tot = 10% power output (W) 4×7 4 × 12 supply voltage (V) 14.4 14.4 load impedance () 4 2
s s
s
4
s s s s
s
mode switch diagnostic
VP 10 k 16 5 13 100 nF 2200 µF
s
14 220 nF input 1
s s
1
TDA8562Q TDA8565Q
6 1000 µF 60 k
These are car audio class-B power amplifiers with internally fixed gain for excellent channel balance (within 1 dB). They are for quad (front and rear stereo) car audio applications. The two types are identical except that the TDA8562Q has a fixed closed-loop voltage gain of 20 dB, whilst that of the TDA8565Q is 20 dB higher. A diagnostic facility senses distortion, load short-circuit and temperature.