Text preview for : Service Manual TG-2900A ( Chassis N ).pdf part of Admiral TG2900-A, TGF2900-A Service Manual TV Admiral Chasis PTNM04-MP (N version)
Back to : Service Manual TG-2900A ( | Home
2 9 "N " Chassis
CONTENTS
1. PRECAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Safety Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 No Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Servicing Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 In stand-by status (POWER OK), TV is switched on,
Precautions for Electrostatically Sensitive Devices . . . . . 6 SMPS turns off and LED turns off (ON/OFF) . . . . . . . . . . . 26
2. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 No Picture (sound ok) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3. DESCRIPTION OF CONTROLS . . . . . . . . . . . . . . . . . . . . . . 8 No Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4. ALIGNMENT AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . 9 Vertical Line(Reference Line) . . . . . . . . . . . . . . . . . . . . . . 29
Preadjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7. BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Factory / Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 8. PCB LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Other Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 9. PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5. USING DEVICES AND DESCRIPTION . . . . . . . . . . . . . . . . 16 10. CRICUIT DIAGRAM
Main IC (TV Processor/u-com/ TMPA8857) . . . . . . . . . . . 16
15W+15W Dual Bridge Amplifier (TDA7297) . . . . . . . . . . 17
MSP 3420G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power (KA5Q1265RF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Vertical deflection output circuit(LA78045) . . . . . . . 23
Triple video output amplifier(TDA6108JF) . . . . . . . 24
1. Precautions
Follow these safety, servicing and ESD precautions to prevent
damage and protect against potential
hazards, such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced.
Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices,
including : nonmetallic control knobs and compartment covers.
3. Make sure that there no cabinet openings through which people-particularly childrenmight
insert fingers and contact dangerous voltages. Such opening include the spacing between
the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and impro-
perly fitted back covers.
If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an
abnormality exists that must be corrected before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1) :
Warning : Do not use an isolation transformer during this test. Use a leakage current
tester or a metering system that complies with International Electrotechnical Commission
65.(IEC 65)
READING SHOULD NOT
BE ABOVE
0.7mA PEAK AC2mA DC.
LEAKAGE
CURRENT
TEATER
CEVICE
UNDER
POWER TEST
CORD TEST ALL
EXPOSED METAL
SURFACES
ALSO TEST WITH
PLUG REVERSED
EARTH
GROUND
FIGURE 1-1
AC LEAKAGE TEST
5. With the unit completely reassembled, plug the AC line cord directly the power outlet.
With the unit' s AC switch first in the ON position and then OFF, measure the current
between a known earth ground (metal water pipe, conduit, etc) and all exposed metal
parts, including: antennas, handle brackets, metal cabinets, screwheads and control
shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug
prongs in the AC outlet and repeat the test.
6. Antenna Cold Check:
With the unit's AC plug disconnected from the AC source, connect an electrical jumper
across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect
the other lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to prohibit X-ray emissions.
To ensure continued X-ray protection, replace the picture tube only with one that is the
same type as the original. Carefully reinstall the picture tube shields and mounting
hardware: these also provide X-ray protection.
8. High Voltage Limits:
High voltage must be measured each time servicing is done on the +B, horizontal
deflection or high voltage circuits.
9. High voltage is maintained within specified limits by close-tolerance, safety-related
components and adjustments. If the high voltage exceeds the specified limits, check
each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or electrical design of this unit.
Example: Do not add auxiliary audio or video connectors. Such alterations might
create a safety hazard. Also, any design changes or additions will void the
manufacturer' s warranty.
11. Components, parts and wiring that appear to have overheated or that are otherwise
damaged should be replaced with parts that meet the original spec ifications. Always
determine the cause of damage or overheating, and correct any potential hazards.
12. Observe the original lead dress, especially near the following areas:
Antenna wiring, sharp edges, and especially the AC and high voltage power supplies.
Always inspect for pinched, out-of place, or frayed wiring.
Do not change the spacing between components and the printed circuit board. Check
the AC power cord for damage. Make sure that leads and components do not touch
thermally hot parts.
13. Picture Tube Implosion Warning:
The picture tube in this receiver employs "integral implosion" protection.
To ensure continued implosion protection, make sure that the replacement picture tube
is the same as the original.
14. Do not remove, install or handle the picture tube without first putting on shatterproof
goggles equipped with side shields.
Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped
with permanetly attached diflection yoke: do not try to remove such "permanently
attached" yokes from the picture tube.
15. Product Safety Notice:
Some electrical and mechanical parts have special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they give might be lost if the replacement
component differs from the original--even if the replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are indicated in the circuit diagram by
shading( ! )
Use replacement components that have the same ratings, especially for flame
resistance and dielectric strength specifications. A replacement part that does not have
the same safety characteristics as the original might create shock, fire or other hazards.
1-2 Servicing Precautions
Warning 1: First read the "Safety Precaution" section of the manual.
If some unforeseen circumstance creates a conflict between the servicing and safety
precautions, always follow the safety precaution.
Warning 2: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing Precautions are printed on the cabinet. Follow them.
2. Always unplug the unit' s AC power cord from the AC power source before attempting
to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical
plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.
3. Some components are raised above the printed circuit board for safety.
An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped
to prevent contact with thermally hot components.
Reinstall all such elements to their original position.
4. After servicing, always check that the screws, components and wiring have been
correctly reinstalled. Make sure that the portion around the serviced part has not been
damaged.
5. Check the insulation between the blades of the AC plug and accessible conductive parts
(examples: metal panels,. input terminals).
6. Insulation Checking Procedure: Disconnent the power cord from the AC source and
turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of
the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive
parts (see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any
of its assemblies) unless all solid-state heat sinks are correctly installed.
8. Always connect a test instrument' s ground lead to the instrument chassis ground before
connecting the positive lead: always remove the instrument' s ground lead list.
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity.
Such some components are called Electrostatically Sensitive devices (ESDs); examples
include integrated circuits and some field-effect tran sistors. The following techniques will
reduce the occurrence of component damage caused by static electricity.
2. Immediately before handling any semiconductor components or assemblies, drain the
electrostatic charge from your body by, touching a known earth ground. Alternatively,
wear the discharging wrist-strap device. (Be sure to remove it prior to applying power-
this is an electric shock precaution.
3. After removing an ESD-equipped assembly, place it on a conductive surface such as
aluminum foil to prevent accumulation of electrostatic charge.
4. Do not use freon-propelled chemicals. These can generate electrical charges that
damage ESDS.
5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDS.
6. Use only an anti-static solder removal device. Many solder removal devices are not rated
as "anti-static"; these can accumulate sufficient electrical charge to damage ESDS.
7. Do not remove a replacement ESD front its protective package until you are ready to
install it. Most replacement ESDs are packaged with leads that are electrically shorted
together by conductive foam, aluminum foil or other conductive materials.
8. Immediately before removing the protective material from the leads of a replacement
ESD, touch the protective material to the chassis or circuit assembly into which the
device will be installed.
9. Minimize body motions when unpackaged replacement ESDS. Motion, such as brushing
clothes together, or lifting a foot from a carpeted floor can generate, enough static
electricity to damage an ESD.
2. Specifications
RECEPTION SYSTEM NTSC M, PAL M/N
POWER REQUIREMENTS AC 90~250V 50/60Hz(AUTO)
POWER CONSUMPTION 130W
STEREO BTSC - Stereo + SAP
SOUND OUTPUT POWER 10W(R) + 10W(L) AT10% TOTAL HARMONIC DISTORTION
ANTENNA IMPEDANCE 75 OHM UNBALANCED TYPE
VIDEO IF 45.75MHz
OPERATING FREQUENCIES
SOUND IF 41.25MHz
VHF CH : 2 ~ 13
CHANNEL COVERAGE UHF CH : 14 ~ 69
CABLE CH : 1, 14 ~ 125
CHANNEL INDICATION ON - SCREEN DISPLAY
REMOTE CONTROL UNIT REQUIRES TWO 1.5V BATTERIES TYPE AAA SIZE
PROGRAM CH MEMORY 181CH MEMORY
3. Description of controls
FRONT
1
2
2 1 3 4 5 6 7 8 9 10 11
3 4 5 6 7 8 9 10 11
REAR
12 13 14
DVD IN
Y
Cb ANT.
CR
1. Video/Audio 2 In Jacks 8. TV/Video Key
2. Headphone Jack 9. Remote Control Sensor
3. Channel Down ( ) Key 10. Stand-by Indicator
4. Channel Up ( ) Key 11. Main Power Key
5. Volume Down (-) Key 12. Component Video Input Jacks (DVD IN)
6. Volume Up (+) Key 13. Audio/Video In/Out Jacks
7. Menu Key 14. Coaxial cable Connector (75ohm)
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION
TO RAIN OR MOISTURE
4. Alignment and Adjustments
4-1 Preadjustment
4-1-1 Factory Mode
1. Do not attempt these adjustments in the VIDEO mode.
2. The Factory Mode adjustments are necessary when either the EEPROM(IC02) or the CPT
is replaced.
3. Do not tamper with the "Adjustment" screen of the Factory Mode menu. The screen is intended
only for factory use.
4-1-2 When EEPROM (IC02) is replaced
1. When IC02 is replaced all adjustment data revert to their initial values. It is necessary to re-
program this data.
2. After IC02 is replaced, warm up the TV for 10 seconds.
4-1-3 When CPT is replaced
1. Make the following the adjustments after setting up purity and convergence:
White Balance
Vertical center
Vertical size
Horizontal size
4-2 Factory / Service Mode
4-2-1 Procedure for the "Adjustment" Mode
1. This mode uses the standard remote control. In the stand-by mode, Press
display + MENU + 3 + 8 + Power(on) button on the remote controller in --> sequence
2. The Factory Mode will be displayed. The Factory Mode has three components :
SCREEN, PICTURE SIZE, PICTURE CONTROL.
3. Access the Adjustment Mode by pressing the VOLUME keys (Up or Down). The adjustment
Parameters adjusted are listed in the accompanying table, and they are selected by pressing
the CH keys (Up or Down).
4. The VOLUME keys increase or decrease the adjustment values.
4-3 Other Adjustments
4-3-1 General Alignment Instructions
1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check the
basic characteristics such as height, horizontal and vertical sync and focus.
2. Observe the picture for good black and white details. There should be no objectionable
color, shading: if color shading is present, perform the purity and convergence
adjustments described below.
3. Use the specified test equipment or its equivalent.
4. Correct impedance matching is essential.
5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of
the TV. When inserting signal markers, do not allow the marker generator to distort test results.
6. Connect the TV only to an AC power source with voltage and frequency as specified on the
back cover nameplate.
7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that
the power cord is disconnected before replacing any parts.
8. To protect against shock hazard, use an isolation transformer.
4-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after
moving the TV should be unnecessary. But the receiver must be properly degaussed upon
installation .
The degaussing coil operates for about 1 second after the power is switched ON. If the set is
moved or turned in a different direction, the power should be OFF for at least 20 minutes.
If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this
happens, use an external degaussing coil. Slowly move the degaussing coil around the
faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to
a distance of about 6 feet before turning power OFF.
If color shading persists, perform the following Color Purity and Convergence adjustments.
4-3-3 High Voltage Check
CAUTION : There is no HIGH VOLTAGE ADJUSTMENT on this chassis. But +B power must
be adjusted in +120V under the full color bar pattern and normal picture control
level.
Connect an accurate high voltmeter to the second anode of the picture tube.
Tune on the TV. Set the Brightness and Contrast controls to minimum(Zero beam current).
Adjust the Brightness and Contrast controls to both extremes. Ensure that the high voltage does
not exceed 34KV under any conditions.
4-3-4. RF AGC Adjustment
Tune in the strongest channel.
Enter input the AGC in the service mode.
Adjust AGC until color noise disappears.
4-3-5 Screen Voltage Adjustment
1. Turn on TV and warm up the set for 30 minutes regardless of an input signal.
2. After Sufficient warming-up, Press display + MENU + 3 + 8 + Power(on).
3. Select "SCREEN" by pressing the VOLUME keys(+,-).
4. Make white colored line by adjusting "RDC", "GDC", "BDC" as follows;
Cut-off Key Action Key Action
RED(1) VOL(-) RED(-) VOL(+) RED(+)
GREEN(5) VOL(-) GREEN(-) VOL(+) GREEN(+)
BLUE(9) VOL(-) BLUE(-) VOL(+) BLUE(+)
5. Adjust the Screen VR (on the FBT) so that horizontal line is just seen a little.
4-3-6 WHITE BALANCE ADJUSTMENT (MANUAL)
1. Set up : Turn the pure white pattern and warm up the set for 20 minutes.
2. Low -Light Adjustment
1-1. Turn the CONTRAST and BRIGHTNESS controls to 3.0 0.3fl with using CA100
1-2. Adjust RDC, GDC and BDC so that the levels are suitable to each local area.
1-3. Check the result of adjustment using White Balance meter.
LOW LIGHT : X=0.261, Y=0.268
3. HIGH-LIGHT Adjustment
3-1. Turn the CONTRAST and BRIGHTNESS controls to 40 4fl with using CA100
3-2. Adjust GDRV and BDRV so that the levels are suitable to each local area.
3-3. Check the result of adjustment using White Balance meter.
HIGH LIGHT : X=0.261, Y=0.268
NOTE : If a white balance meter is not available than approximate the following color adjustments "
by eye".
4-3-7 FOCUS Adjustment
1. Turn in the active station in your area.
2. Press the P.STD buton on the Remote control for DYNAMIC condition.
3. In put the standard signal. (Cross-Hatch pattern)
4. Adjust the FOCUS control on the FBT to abtain a sharp and clear picture.
4-3-8 Purity Adjustment
1. Warm up the receiver for at least 30 minutes.
2. Plug in the CRT deflection yoke. Tighten the clamp screw.
3. Plug the convergence yoke into the CRT and set it as shown in Fig. B-1.
4. Input a black and white signal.
5. Fully demagnetize the receiver by using an external degaussing coil.
6. Turn the CONTRAST and BRIGHTNESS controls to maximum.
7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to produce a
vertical green belt. (Fig. B-2)
8. Tighten the convergence yoke.
9. Slowly move the deflection yoke forward. Adjust for the best overall green screen.
10. Temporarily tighten the deflection yoke.
11. Produce blue and red rasters by adjusting the-low-light controls.
Check for good purity in each field.
12. Tighten the deflection yoke.
4-3-9 Center Convergence Adjustment
1. Warm up the receiver for at least 30 minutes.
2. Adjust the two tabs of the 4-pole magnets: Change the angle between them.
Superimpose the red and blue vertical lines in the center area of the screen.
3. Adjust the BRIGHTNESS and CONTRAST controls for a well-defined picture.
4. Adjust the two tabs of the 4-pole magnets, and change the angle between them.
Superimpose the red and the blue vertical lines in the center area of the screen.
5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red
and blue horizontal lines in the center of the screen.
6. Adjust two-tabs of 6-pole magnets to superimpose the red and blue lines onto the green.
Adjust the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.
7. Repeat adjustments 2-6, if necessary.
8. Since the 4-pole and 6-pole magnets interact, the dot movement is complex(fig B-3).
FIG. B-1 CONVERGENCE MAGNET ASSEMBLY
Vertical Green Belt
ADJUST
FIG. B-2 CENTER CONVERGENCE ADJUSTMENT
BLUE RED BLUE RED
BLUE BLUE/RED
RED GREEN
4-POLE MAGINETS MOVEMENT 6-POLE MAGINETS MOVEMENT
FIG. B-3 CENTER CONVERGENCE ADJUSTMENT
4-3-10 TEST EQUIPMENT
DIGITAL VOLTMETER . . . . . . . . . . . . . . . . . . . . . Fluke model 8060A or equivalent.
OSCILLOSCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . Kikusui Model cos 2050 or equivalent
DIRECT/LOW-CAPACITY PROBE . . . . . . . . . . . . (Accessory of osc)
COLOR-BAR/DOT/CROSSHATCH
GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . PM 5518 or equivalent
SWEEP/MAKER ALIGNMENT
GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . Leader Model 480-080 or equivalent
BIAS SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . Kikusui Model 7314A or equivalent
(Combined in Model 415 generator)
4-3-11 Geometry Adjustment
(1) Ready of Adjustment.
Turn the monochrome(lion head pattern) channel and warm up the set for 20 minutes.
On factory mode, select screen.
Use Program Up Down key to select of item.
(2) Deflection Adjustment Procedure
S-COR(Vertical S Correction)
V-SLOPE(Vertical Linerarity)
VRS(Vertical Shift)
HIGHT(Vertical Height)
HRS (60)(60Hz Horizontal Shift)
H-SIZE(East-West Width)
PINCUSH.(East-West Paraboola)
EW-UPPER(Upper East-West Corner)
EW-LOWER(Bottom East-West Corner)
EW-TRAP(East-West Trapezium)
5. Using Devices and Description
5-1 MAIN IC(TV PROCESSOR/U-COM,TMPA8857
5-2. 15+15W DUAL BRIDGE AMPLIFIER(TDA7297)
5-2-3. BLOCK DIAGRAM
5-3 MSP 3420G
5-3-1 Feature
- AVC: Automatic Volume Correction
- Subwoofer Output
- 5-band graphic equalizer (as in MSP 3420G)
- Enhanced spatial effect (pseudostereo/basewidth enlargement as in MSP 3420G)
- headphone channel with balance, bass, treble, loudness
- balance for loudspeaker and headphone channels in dB units (option)
- Additional SCART input
- Full SCART in/out matrix without restrictions
- Scart volume in dB units (optional)
- Additional I2S input
- New FM-identification
- Demodulator short programming
- Autodetection for terrestrial TV-sound standards
- Precise bit-error rate indication
- Automatic switching from NICAM to FM/AM or vice versa
- Improved NICAM synchronization algorithm
- Improved carrier mute algorithm
- Improved AM-demodulation
- Dolby Pro Logic together with DPL 35xx A
- Reduction of necessary controlling
- Less external components
- Significant reduction of radiation
5-3-2 PRELIMINARY DATA SHEET
5-3-3 Application Circuit
MSP 3420G
Note : Pin numbers refer to PLCC68 package, numbers in brackets refer to the PSDIP64 package.
5-4. POWER (KA5Q1265RF)
KA5Q-SERIES
KA5Q0765RT/KA5Q12656RT/KA5Q1265RF/KA5Q1565RF
Fairchild Power Switch (FPS)
5-5 Vertical deflection output circuit(LA78045)
5-6 Triple video output amplifier(TDA6108JF)
5-6-1. Features
Typical bandwidth of 9.0MHz for an output signal of 60V(p-p)
High slew rate of 1850V/ s
No external components required
Very simple application
Single supply voltage of 200V
Internal reference voltage of 2.5V
5-6-2. PINNING
SYMBOL PIN DESCRIPTION
Vi(1) 1 inverting input 1
Vi(2) 2 inverting input 2
Vi(3) 3 inverting input 3
GND 4 grund (fin)
Iom 5 black current measurement output
VDD 6 supply voltage
VoC(3) 7 cathode output 3
VoC(3) 8 cathode output 2
VoC(3) 9 cathode output 1
5-6-3. BLOCK DIAGRAM
VDD
6
MIRROR 1 MIRROR 5
TDA6108JF CASCODE 1
3×
MIRROR 4
Voc(3),
CURRENT 9, 8, 7
1× Voc(2),
SOURCE
Voc(1)
1×
THERMAL Rf
PROTECTION VIP DIFFERENTIAL
CIRCUIT REFERENCE STAGE
Vi(1),
Vi(2), 1, 2, 3 5
MIRROR 3 Io(m)
Vi(3) Ri
Ra
3× CASCODE 2
MIRROR 2
4
MGL318
6. TROUBLESHOOTING
1. No Power
PROCESS
NO 1) CHECK THE POWER
CHECK THE VOLTAGE SUPPLY OUTLET
BETWEEN P801 2) CHECK THE POWER CORD
AC 220V
YES 1) CHECK F801(250V 5A)
IF F801 IS BROKEN, REPLACE IT AFTER
CHECKING THESE :
CHECK THE D801
VOLTAGE BETWEEN NO RESISTANCE VALUE BETWEEN
"+" LINE AND "-" PIN 1 AND P1N2 OF IC81 ( IS OK)
LINE OF L801 2) CHECK L801
AC 220V
3) CHECK C801
YES
1) CHECK THE RESISTER VALUE OF NT801
CHECK THE NO 2) CHECK D801(BRIDGE DIODE)
VOLTAGE OF T801 3) CHECK THE RESISTER VALUE BETWEEN 1
OF PIN1 AND 2 OF IC81( IS OK)
DC 310V 4) CHECK T801
YES
CHECK THE CHECK THESE :
NO
VOLTAGE IC81 1) IC81 : KA5Q1265RF
OF PIN3 2) D803, R804
STAND BY : 13V
TV ON : 17V
YES (NORMAL)
CHECK THE NO CHECK THE RESISTANCE VALUE BETWEEN
VOLTAGE OF IC82 PIN3 AND PIN4 OF IC82( IS OK)
PIN4(PC817)
DC 3.3V
YES
CHECK THE CHECK AND REPLACE
NO
VOLTAGE BETWEEN 1) Q871, D827
Q871 "E" AND 2) Q831, Q863, D831
GND
STAND BY : 5V
YES
CHECK
THE VOLTAGE NO CHECK AND REPLACE
BETWEEN C822 1) D821, IC83
AND GND
DC 120V
YES
END
2. In stand-by status (POWER OK), TV is switched on, SMPS turns off
and LED turns off (ON/OFF)
Cause : If IC81 becomes off because secondary side of SMPS is overloaded, primary side of
SMPS may be normal.
START
1) OPEN L823 AND
NO
CONNECT Q831 TO BASE GND
2) CHECK THE VOLTAGE
OF C822
DC 120V
YES
CHECK THE NO CHECK THE RESISTANCE VALUE
VOLTAGE OF IC82 BETWEEN PIN3 AND PIN4 OF IC82
PIN2
DC 10.5V
YES
CHECK THE NO
VOLTAGE OF IC51 REPLACE µ-COM(IC51)
PIN64
TV ON : 1.5V
STAND BY : 0V
YES
CHECK Q861, Q862, Q863
CHECK THE RESISTANCE REPLACE IC82 IF THE
VALUE "E "AND "C" OF VOLTAGE OF IC82
Q404 (REPLACE TR 0) PIN4 IS 0V
3. No Picture(sound ok)
START
CHECK D827
CHECK NO CHECK NO R861, Q861
THE WAVEFORM AT THE VOLTAGE AT Q862, D861
IC51 PIN30 IC51 PIN29 D862
DC 9V
YES YES
REPLACE
IC51
CHECK NO CHECK NO CHECK
THE WAVEFORM AT THE WAVEFORM AT Q401, R413
Q404 "B " Q401 "C "
YES
CHECK NO
THE WAVEFORM AT CHECK Q404
IC51 PIN13
YES YES
CHECK R910 REPLACE T401
4. No Sound
START
CHECK
NO
VOLTAGE AT IC63 PIN3 CHECK D825, R659
DC 17V
YES
CHECK
YES
IC63 PIN4, 12 CHECK SPEAKER, IC63
WAVEFORMS
NO
CHECK THE
YES 1) CHECK
WAVEFORMS AT
IC62 PIN 24, 25 Q653,Q654,D651
NO
CHECK THE YES 1)CHECK VOLUME, BALANCE
WAVEFORMS AT
CHECK IC62, QN03
IC16 PIN6
NO
CHECK IC16, Z102
5. Vertical Line(Reference Line)
START
CHECK
NO CHECK D383, R382
VOLTAGE AT IC31
PIN2, PIN4 D851, R383
V2=+16.5V
V4=-16.5V
YES
CHECK
NO
WAVEFORM CHECK IC51
IC31, PIN1
YES
CHECK
NO
WAVEFORM CHECK IC31
IC31, PIN5
YES
CHECK DY CONNECTOR
7. BLOCK DIAGRAM
8. PCB LAYOUT(MAIN)
PCB LAYOUT(SUB)
PCB LAYOUT(PIP)
ELECTRICAL PARTS LIST
P / No. ITEM No. ITEM NAME P / No. ITEM No. ITEM NAME
A001 150013111 "MAIN, NTSC PTNM04 29GN2BU" DV21 11115638T "ZD, MTZJ8.2B (VZ7.78-8.19) 0.5W"
A001R 150610830 "MAIN, RHU PTNM04 29GN2BU" DZ802 11115678T "ZD, MTZJ27B (VZ24.97-26.26) 0.5W"
A001U 150111454 "MAIN, AUTO PTNM04 29GN2BU" DZ803 11115664T "ZD, MTZJ18C (VZ17.42-18.33) 0.5W"
A001A 150211583 "MAIN, AXIAL PTNM04 29GN2BU" EL02 11061303 "EYELET, HTR 2.80*2.9 SNI"
C035 12474102T "CERAMIC CAP, B 50V 1000PF K AXIAL" EL03 11061303 "EYELET, HTR 2.80*2.9 SNI"
C036 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL04 11061303 "EYELET, HTR 2.80*2.9 SNI"
C044 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL05 11061303 "EYELET, HTR 2.80*2.9 SNI"
C055 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL06 11061303 "EYELET, HTR 2.80*2.9 SNI"
C104 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL07 11061303 "EYELET, HTR 2.80*2.9 SNI"
C161 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL08 11061303 "EYELET, HTR 2.80*2.9 SNI"
C163 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL09 11061303 "EYELET, HTR 2.80*2.9 SNI"
C165 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL10 11061303 "EYELET, HTR 2.80*2.9 SNI"
C166 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL11 11061303 "EYELET, HTR 2.80*2.9 SNI"
C181 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL12 11061303 "EYELET, HTR 2.80*2.9 SNI"
C187 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL13 11061303 "EYELET, HTR 2.80*2.9 SNI"
C503 12474102T "CERAMIC CAP, B 50V 1000PF K AXIAL" EL14 11061303 "EYELET, HTR 2.80*2.9 SNI"
C523 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" EL15 11061303 "EYELET, HTR 2.80*2.9 SNI"
C531 12474102T "CERAMIC CAP, B 50V 1000PF K AXIAL" EL16 11061303 "EYELET, HTR 2.80*2.9 SNI"
C557 12473470T "CERAMIC CAP, SL 50V 47PF J AXIAL" EL17 11061303 "EYELET, HTR 2.80*2.9 SNI"
C557 12473470AT "CERAMIC CAP, SL 50V 47PF J AXIAL" EL18 11061303 "EYELET, HTR 2.80*2.9 SNI"
C558 12473470T "CERAMIC CAP, SL 50V 47PF J AXIAL" EL19 11061303 "EYELET, HTR 2.80*2.9 SNI"
C558 12473470AT "CERAMIC CAP, SL 50V 47PF J AXIAL" EL20 11061303 "EYELET, HTR 2.80*2.9 SNI"
C563 12474102T "CERAMIC CAP, B 50V 1000PF K AXIAL" EL21 11061303 "EYELET, HTR 2.80*2.9 SNI"
C572 12474181T "CERAMIC CAP, B 50V 180PF K AXIAL" EL23 11061303 "EYELET, HTR 2.80*2.9 SNI"
C574 12474561T "CERAMIC CAP, B 50V 560PF K AXIAL" EL31 11061303 "EYELET, HTR 2.80*2.9 SNI"
CN03 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES01 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN06 12474332T "CERAMIC CAP, B 50V 3300PF K AXIAL" ES02 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN07 12474332T "CERAMIC CAP, B 50V 3300PF K AXIAL" ES03 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN08 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES04 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN12 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES05 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN16 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES06 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN24 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES07 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN27 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES08 11061202 "EYELET, HTR 2.11*2.8 SNI"
CN28 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES09 11061202 "EYELET, HTR 2.11*2.8 SNI"
CV21 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES10 11061202 "EYELET, HTR 2.11*2.8 SNI"
CV81 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" ES11 11061202 "EYELET, HTR 2.11*2.8 SNI"
D027 11115024T "SILICON DIODE, 1N4148" ES12 11061202 "EYELET, HTR 2.11*2.8 SNI"
D103 11115686T "ZD, MTZJ33B (VZ30.32-31.88) 0.5W" ES13 11061202 "EYELET, HTR 2.11*2.8 SNI"
D311 11115003T "SILICON DIODE, 1N4004" ES14 11061202 "EYELET, HTR 2.11*2.8 SNI"
D340 11115024T "SILICON DIODE, 1N4148" ES15 11061202 "EYELET, HTR 2.11*2.8 SNI"
D341 11115626T "ZD, MTZJ5.6B (VZ5.45-5.73) 0.5W" ES16 11061202 "EYELET, HTR 2.11*2.8 SNI"
D351 11115777T "DIODE-REC, 1N4758A,56V,1W,DO-41" ES17 11061202 "EYELET, HTR 2.11*2.8 SNI"
D383 11115458T "DIODE, FAST RECOVERY UF-156" ES18 11061202 "EYELET, HTR 2.11*2.8 SNI"
D410 11115638T "ZD, MTZJ8.2B (VZ7.78-8.19) 0.5W" ES19 11061202 "EYELET, HTR 2.11*2.8 SNI"
D441 11115014T "SILICON DIODE, RGP10J" ES20 11061202 "EYELET, HTR 2.11*2.8 SNI"
D517 11115024T "SILICON DIODE, 1N4148" ES21 11061202 "EYELET, HTR 2.11*2.8 SNI"
D527 11115615T "ZD, MTZJ3.9B (VZ3.89-4.16) 0.5W" ES22 11061202 "EYELET, HTR 2.11*2.8 SNI"
D550 11115645T "ZD, MTZJ10C (VZ9.70-10.20) 0.5W" ES23 11061202 "EYELET, HTR 2.11*2.8 SNI"
D551 11115645T "ZD, MTZJ10C (VZ9.70-10.20) 0.5W" ES24 11061202 "EYELET, HTR 2.11*2.8 SNI"
D552 11115645T "ZD, MTZJ10C (VZ9.70-10.20) 0.5W" ES25 11061202 "EYELET, HTR 2.11*2.8 SNI"
D651 11115615T "ZD, MTZJ3.9B (VZ3.89-4.16) 0.5W" ES26 11061202 "EYELET, HTR 2.11*2.8 SNI"
D802 11115464T "DIODE, RECTIFIER 1N5398E" ES27 11061202 "EYELET, HTR 2.11*2.8 SNI"
D808 11115224T "DIODE, FAST RECOVERY 1N4937" ES28 11061202 "EYELET, HTR 2.11*2.8 SNI"
D809 11115024T "SILICON DIODE, 1N4148" ES29 11061202 "EYELET, HTR 2.11*2.8 SNI"
D823 11115014T "SILICON DIODE, RGP10J" ES30 11061202 "EYELET, HTR 2.11*2.8 SNI"
D827 11115014T "SILICON DIODE, RGP10J" ES31 11061202 "EYELET, HTR 2.11*2.8 SNI"
D831 11115024T "SILICON DIODE, 1N4148" ES33 11061202 "EYELET, HTR 2.11*2.8 SNI"
D834 11115444T "DIODE, RGP15J" ES34 11061202 "EYELET, HTR 2.11*2.8 SNI"
D851 11115458T "DIODE, FAST RECOVERY UF-156" ES35 11061202 "EYELET, HTR 2.11*2.8 SNI"
D852 11115626T "ZD, MTZJ5.6B (VZ5.45-5.73) 0.5W" ES36 11061202 "EYELET, HTR 2.11*2.8 SNI"
D861 11115641T "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" ES37 11061202 "EYELET, HTR 2.11*2.8 SNI"
D862 11115024T "SILICON DIODE, 1N4148" ES38 11061202 "EYELET, HTR 2.11*2.8 SNI"
D871 11115626T "ZD, MTZJ5.6B (VZ5.45-5.73) 0.5W" ES39 11061202 "EYELET, HTR 2.11*2.8 SNI"
DE01 11115024T "SILICON DIODE, 1N4148" ES40 11061202 "EYELET, HTR 2.11*2.8 SNI"
DF01 11115224T "DIODE, FAST RECOVERY 1N4937" ES41 11061202 "EYELET, HTR 2.11*2.8 SNI"
DF02 11115626T "ZD, MTZJ5.6B (VZ5.45-5.73) 0.5W" ES42 11061202 "EYELET, HTR 2.11*2.8 SNI"
DV11 11115641T "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" ES43 11061202 "EYELET, HTR 2.11*2.8 SNI"
DV12 11115641T "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" ES44 11061202 "EYELET, HTR 2.11*2.8 SNI"
DV13 11115641T "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" ES45 11061202 "EYELET, HTR 2.11*2.8 SNI"
ELECTRICAL PARTS LIST
P / No. ITEM No. ITEM NAME P / No. ITEM No. ITEM NAME
ES46 11061202 "EYELET, HTR 2.11*2.8 SNI" J075 11183004 "PLATING WIRE, 0.6MM"
ES47 11061202 "EYELET, HTR 2.11*2.8 SNI" J077 11183004 "PLATING WIRE, 0.6MM"
J001 11183004 "PLATING WIRE, 0.6MM" J078 11183004 "PLATING WIRE, 0.6MM"
J002 11183004 "PLATING WIRE, 0.6MM" J079 11183004 "PLATING WIRE, 0.6MM"
J003 11183004 "PLATING WIRE, 0.6MM" J080 11183004 "PLATING WIRE, 0.6MM"
J004 11183004 "PLATING WIRE, 0.6MM" J082 11183004 "PLATING WIRE, 0.6MM"
J005 11183004 "PLATING WIRE, 0.6MM" J083 11183004 "PLATING WIRE, 0.6MM"
J006 11183004 "PLATING WIRE, 0.6MM" J084 11183004 "PLATING WIRE, 0.6MM"
J007 11183004 "PLATING WIRE, 0.6MM" J085 11183004 "PLATING WIRE, 0.6MM"
J008 11183004 "PLATING WIRE, 0.6MM" J086 11183004 "PLATING WIRE, 0.6MM"
J009 11183004 "PLATING WIRE, 0.6MM" J087 11183004 "PLATING WIRE, 0.6MM"
J010 11183004 "PLATING WIRE, 0.6MM" J088 11183004 "PLATING WIRE, 0.6MM"
J011 11183004 "PLATING WIRE, 0.6MM" J089 11183004 "PLATING WIRE, 0.6MM"
J012 11183004 "PLATING WIRE, 0.6MM" J090 11183004 "PLATING WIRE, 0.6MM"
J013 11183004 "PLATING WIRE, 0.6MM" J091 11183004 "PLATING WIRE, 0.6MM"
J014 11183004 "PLATING WIRE, 0.6MM" J092 11183004 "PLATING WIRE, 0.6MM"
J015 11183004 "PLATING WIRE, 0.6MM" J093 11183004 "PLATING WIRE, 0.6MM"
J016 11183004 "PLATING WIRE, 0.6MM" J094 11183004 "PLATING WIRE, 0.6MM"
J017 11183004 "PLATING WIRE, 0.6MM" J095 11183004 "PLATING WIRE, 0.6MM"
J018 11183004 "PLATING WIRE, 0.6MM" J096 11183004 "PLATING WIRE, 0.6MM"
J020 11183004 "PLATING WIRE, 0.6MM" J097 11183004 "PLATING WIRE, 0.6MM"
J021 11183004 "PLATING WIRE, 0.6MM" J098 11183004 "PLATING WIRE, 0.6MM"
J022 11183004 "PLATING WIRE, 0.6MM" J099 11183004 "PLATING WIRE, 0.6MM"
J023 11183004 "PLATING WIRE, 0.6MM" J100 11183004 "PLATING WIRE, 0.6MM"
J024 11183004 "PLATING WIRE, 0.6MM" J101 11183004 "PLATING WIRE, 0.6MM"
J025 11183004 "PLATING WIRE, 0.6MM" J102 11183004 "PLATING WIRE, 0.6MM"
J026 11183004 "PLATING WIRE, 0.6MM" J103 11183004 "PLATING WIRE, 0.6MM"
J028 11183004 "PLATING WIRE, 0.6MM" J104 11183004 "PLATING WIRE, 0.6MM"
J029 11183004 "PLATING WIRE, 0.6MM" J105 11183004 "PLATING WIRE, 0.6MM"
J030 11183004 "PLATING WIRE, 0.6MM" J106 11183004 "PLATING WIRE, 0.6MM"
J031 11183004 "PLATING WIRE, 0.6MM" J107 11183004 "PLATING WIRE, 0.6MM"
J033 11183004 "PLATING WIRE, 0.6MM" J108 11183004 "PLATING WIRE, 0.6MM"
J034 11183004 "PLATING WIRE, 0.6MM" J109 11183004 "PLATING WIRE, 0.6MM"
J035 11183004 "PLATING WIRE, 0.6MM" J110 11183004 "PLATING WIRE, 0.6MM"
J036 11183004 "PLATING WIRE, 0.6MM" J111 11183004 "PLATING WIRE, 0.6MM"
J037 11183004 "PLATING WIRE, 0.6MM" J112 11183004 "PLATING WIRE, 0.6MM"
J038 11183004 "PLATING WIRE, 0.6MM" J113 11183004 "PLATING WIRE, 0.6MM"
J039 11183004 "PLATING WIRE, 0.6MM" J114 11183004 "PLATING WIRE, 0.6MM"
J040 11183004 "PLATING WIRE, 0.6MM" J115 11183004 "PLATING WIRE, 0.6MM"
J041 11183004 "PLATING WIRE, 0.6MM" J116 11183004 "PLATING WIRE, 0.6MM"
J042 11183004 "PLATING WIRE, 0.6MM" J117 11183004 "PLATING WIRE, 0.6MM"
J044 11183004 "PLATING WIRE, 0.6MM" J118 11183004 "PLATING WIRE, 0.6MM"
J045 11183004 "PLATING WIRE, 0.6MM" J119 11183004 "PLATING WIRE, 0.6MM"
J046 11183004 "PLATING WIRE, 0.6MM" J120 11183004 "PLATING WIRE, 0.6MM"
J047 11183004 "PLATING WIRE, 0.6MM" J121 11183004 "PLATING WIRE, 0.6MM"
J048 11183004 "PLATING WIRE, 0.6MM" J122 11183004 "PLATING WIRE, 0.6MM"
J050 11183004 "PLATING WIRE, 0.6MM" J123 11183004 "PLATING WIRE, 0.6MM"
J052 11183004 "PLATING WIRE, 0.6MM" J124 11183004 "PLATING WIRE, 0.6MM"
J053 11183004 "PLATING WIRE, 0.6MM" J125 11183004 "PLATING WIRE, 0.6MM"
J054 11183004 "PLATING WIRE, 0.6MM" J126 11183004 "PLATING WIRE, 0.6MM"
J055 11183004 "PLATING WIRE, 0.6MM" J127 11183004 "PLATING WIRE, 0.6MM"
J056 11183004 "PLATING WIRE, 0.6MM" J128 11183004 "PLATING WIRE, 0.6MM"
J057 11183004 "PLATING WIRE, 0.6MM" J129 11183004 "PLATING WIRE, 0.6MM"
J058 11183004 "PLATING WIRE, 0.6MM" J130 11183004 "PLATING WIRE, 0.6MM"
J060 11183004 "PLATING WIRE, 0.6MM" J132 11183004 "PLATING WIRE, 0.6MM"
J061 11183004 "PLATING WIRE, 0.6MM" J133 11183004 "PLATING WIRE, 0.6MM"
J062 11183004 "PLATING WIRE, 0.6MM" J134 11183004 "PLATING WIRE, 0.6MM"
J063 11183004 "PLATING WIRE, 0.6MM" J135 11183004 "PLATING WIRE, 0.6MM"
J064 11183004 "PLATING WIRE, 0.6MM" J136 11183004 "PLATING WIRE, 0.6MM"
J065 11183004 "PLATING WIRE, 0.6MM" J137 11183004 "PLATING WIRE, 0.6MM"
J066 11183004 "PLATING WIRE, 0.6MM" J139 11183004 "PLATING WIRE, 0.6MM"
J067 11183004 "PLATING WIRE, 0.6MM" J140 11183004 "PLATING WIRE, 0.6MM"
J068 11183004 "PLATING WIRE, 0.6MM" J142 11183004 "PLATING WIRE, 0.6MM"
J069 11183004 "PLATING WIRE, 0.6MM" J143 11183004 "PLATING WIRE, 0.6MM"
J070 11183004 "PLATING WIRE, 0.6MM" J160 11183004 "PLATING WIRE, 0.6MM"
J071 11183004 "PLATING WIRE, 0.6MM" J801 11183004 "PLATING WIRE, 0.6MM"
J072 11183004 "PLATING WIRE, 0.6MM" JP20 11183004 "PLATING WIRE, 0.6MM"
J073 11183004 "PLATING WIRE, 0.6MM" JP21 11183004 "PLATING WIRE, 0.6MM"
J074 11183004 "PLATING WIRE, 0.6MM" JP22 11183004 "PLATING WIRE, 0.6MM"
ELECTRICAL PARTS LIST
P / No. ITEM No. ITEM NAME P / No. ITEM No. ITEM NAME
L110 11237100T "COIL, AXIAL LAL02TB 10UH K" R320 12919109T "CARBON RESISTOR, SB 1/2W 1 OHM J"
L161 11237688T "COIL, AXIAL LAL02TB 0.68UH K" R340 12368822T "CARBON RESISTOR, SB 1/6W 8.2K OHM J"
L181 11237100T "COIL, AXIAL LAL02TB 10UH K" R341 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J"
L182 11237100T "COIL, AXIAL LAL02TB 10UH K" R382 12531478T "FUSE RESISTOR, RN A 1/2W 0.47 OHM J"
L183 11237100T "COIL, AXIAL LAL02TB 10UH K" R383 12531478T "FUSE RESISTOR, RN A 1/2W 0.47 OHM J"
L201 11237829T "COIL, AXIAL LAL02TB 8.2UH K" R402 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
L301 11230100T "INDUCTOR-AXIAL, AL04 TB 10UH-K" R404 12321102T "OXIDE RESISTOR, B 1/2W 1K OHM J"
L404 11103041T "B-CORE, BF40 BTL3.5*7B-AG(0.62X63)" R405 12368752T "CARBON RESISTOR, SB 1/6W 7.5K OHM J"
L404 C1103095T "B-CORE, RH03506ST-B" R409 12368473T "CARBON RESISTOR, SB 1/6W 47K OHM J"
L509 11237100T "COIL, AXIAL LAL02TB 10UH K" R410 12368270T "CARBON RESISTOR, SB 1/6W 27 OHM J"
L517 11237470T "COIL, AXIAL LAL02TB 47UH K" R411 12321512T "OXIDE RESISTOR, B 1/2W 5.1K OHM J"
L536 11237100T "COIL, AXIAL LAL02TB 10UH K" R413 12321109T "OXIDE RESISTOR, B 1/2W 1 OHM J"
L544 11237100T "COIL, AXIAL LAL02TB 10UH K" R432 12321102T "OXIDE RESISTOR, B 1/2W 1K OHM J"
L555 11237100T "COIL, AXIAL LAL02TB 10UH K" R441 12531478T "FUSE RESISTOR, RN A 1/2W 0.47 OHM J"
L806 11103041T "B-CORE, BF40 BTL3.5*7B-AG(0.62X63)" R442 12919224T "CARBON RESISTOR, SB 1/2W 220K OHM J"
L806 C1103095T "B-CORE, RH03506ST-B" R445 12531478T "FUSE RESISTOR, RN A 1/2W 0.47 OHM J"
L807 11103041T "B-CORE, BF40 BTL3.5*7B-AG(0.62X63)" R495 12371102T "METAL RESISTOR, RN 1/2W 1KF"
L807 C1103095T "B-CORE, RH03506ST-B" R496 12371623T "METAL RESISTOR, RN 1/2W 62K F"
L808 11103041T "B-CORE, BF40 BTL3.5*7B-AG(0.62X63)" R501 12368681T "CARBON RESISTOR, SB 1/6W 680 OHM J"
L808 C1103095T "B-CORE, RH03506ST-B" R502 12368333T "CARBON RESISTOR, SB 1/6W 33K OHM J"
L821 11103041T "B-CORE, BF40 BTL3.5*7B-AG(0.62X63)" R503 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J"
L821 C1103095T "B-CORE, RH03506ST-B" R505 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J"
L825 11103041T "B-CORE, BF40 BTL3.5*7B-AG(0.62X63)" R512 12368512T "CARBON RESISTOR, SB 1/6W 5.1K OHM J"
L825 C1103095T "B-CORE, RH03506ST-B" R513 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J"
LE01 11237100T "COIL, AXIAL LAL02TB 10UH K" R514 12368822T "CARBON RESISTOR, SB 1/6W 8.2K OHM J"
LN01 11237100T "COIL, AXIAL LAL02TB 10UH K" R519 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
LN02 11237100T "COIL, AXIAL LAL02TB 10UH K" R520 12368221T "CARBON RESISTOR, SB 1/6W 220 OHM J"
LN03 11237109T "COIL, AXIAL LAL02TB 1UH K" R521 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
LV81 11237109T "COIL, AXIAL LAL02TB 1UH K" R525 12919271T "CARBON RESISTOR, SB 1/2W 270 OHM J"
N001A 11965057 "TAPE, YW-5006 6.2MM*2000M ROLL" R526 12368201T "CARBON RESISTOR, SB 1/6W 200 OHM J"
N001B 11965058 "TAPE, TESAKREPP-4387 6.0MM*2000M" R527 12368393T "CARBON RESISTOR, SB 1/6W 39K OHM J"
R003 12368333T "CARBON RESISTOR, SB 1/6W 33K OHM J" R528 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R013 12368471T "CARBON RESISTOR, SB 1/6W 470 OHM J" R530 12368302T "CARBON RESISTOR, SB 1/6W 3K OHM J"
R018 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J" R531 12368332T "CARBON RESISTOR, SB 1/6W 3.3K OHM J"
R020 12368112T "CARBON RESISTOR, SB 1/6W 1.1K OHMJ" R535 12368155T "CARBON RESISTOR, SB 1/6W 1.5M OHMJ"
R021 12368561T "CARBON RESISTOR, SB 1/6W 560 OHM J" R545 12368332T "CARBON RESISTOR, SB 1/6W 3.3K OHM J"
R027 12368203T "CARBON RESISTOR, SB 1/6W 20K OHM J" R546 12368224T "CARBON RESISTOR, SB 1/6W 220K OHM J"
R028 12368333T "CARBON RESISTOR, SB 1/6W 33K OHM J" R547 12368473T "CARBON RESISTOR, SB 1/6W 47K OHM J"
R030 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R548 12368153T "CARBON RESISTOR, SB 1/6W 15K OHM J"
R035 12368221T "CARBON RESISTOR, SB 1/6W 220 OHM J" R550 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R057 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J" R551 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R058 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J" R552 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R101 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R557 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R102 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R558 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R103 12321222T "OXIDE RESISTOR, B 1/2W 2.2K OHM J" R561 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J"
R106 12368222T "CARBON RESISTOR, SB 1/6W 2.2K OHM J" R562 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J"
R111 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R563 12368511T "CARBON RESISTOR, SB 1/6W 510 OHM J"
R112 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R564 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J"
R113 12368331T "CARBON RESISTOR, SB 1/6W 330 OHM J" R565 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J"
R116 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R571 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J"
R118 12368563T "CARBON RESISTOR, SB 1/6W 56K OHM J" R572 12368222T "CARBON RESISTOR, SB 1/6W 2.2K OHM J"
R119 12368123T "CARBON RESISTOR, SB 1/6W 12K OHM J" R573 12368152T "CARBON RESISTOR, SB 1/6W 1.5K OHMJ"
R121 12368472T "CARBON RESISTOR, SB 1/6W 4.7K OHM J" R574 12368564T "CARBON RESISTOR, SB 1/6W 560K OHM J"
R122 12368681T "CARBON RESISTOR, SB 1/6W 680 OHM J" R575 12368471T "CARBON RESISTOR, SB 1/6W 470 OHM J"
R162 12368472T "CARBON RESISTOR, SB 1/6W 4.7K OHM J" R576 12368683T "CARBON RESISTOR, SB 1/6W 68K OHM J"
R163 12368270T "CARBON RESISTOR, SB 1/6W 27 OHM J" R577 12368123T "CARBON RESISTOR, SB 1/6W 12K OHM J"
R164 12368122T "CARBON RESISTOR, SB 1/6W 1.2K OHM J" R578 12368392T "CARBON RESISTOR, SB 1/6W 3.9K OHM J"
R165 12368331T "CARBON RESISTOR, SB 1/6W 330 OHM J" R579 12368392T "CARBON RESISTOR, SB 1/6W 3.9K OHM J"
R167 12368221T "CARBON RESISTOR, SB 1/6W 220 OHM J" R580 12368223T "CARBON RESISTOR, SB 1/6W 22K OHM J"
R181 12368221T "CARBON RESISTOR, SB 1/6W 220 OHM J" R651 12368431T "CARBON RESISTOR, SB 1/6W 430 OHM J"
R201 12368470T "CARBON RESISTOR, SB 1/6W 47 OHM J" R652 12368431T "CARBON RESISTOR, SB 1/6W 430 OHM J"
R202 12368201T "CARBON RESISTOR, SB 1/6W 200 OHM J" R653 12368911T "CARBON RESISTOR, SB 1/6W 910 OHM J"
R203 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" R654 12368911T "CARBON RESISTOR, SB 1/6W 910 OHM J"
R204 12368161T "CARBON RESISTOR, SB 1/6W 160 OHM J" R657 12368123T "CARBON RESISTOR, SB 1/6W 12K OHM J"
R307 12371562T "METAL RESISTOR, RN 1/2W 5.6K F" R658 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J"
R311 12328562T "METAL RESISTOR, K 1/6W 5.6K OHM F" R660 12368472T "CARBON RESISTOR, SB 1/6W 4.7K OHM J"
R312 12328223T "METAL RESISTOR, K 1/6W 22K OHM F" R661 12368222T "CARBON RESISTOR, SB 1/6W 2.2K OHM J"
R313 12328203T "METAL RESISTOR, K 1/6W 20K OHM F" R662 12368153T "CARBON RESISTOR, SB 1/6W 15K OHM J"
R314 12328392T "METAL RESISTOR, K 1/6W 3.9K OHM F" R666 12321331T "OXIDE RESISTOR, B 1/2W 330 OHM J"
ELECTRICAL PARTS LIST
P / No. ITEM No. ITEM NAME P / No. ITEM No. ITEM NAME
R667 12321331T "OXIDE RESISTOR, B 1/2W 330 OHM J" RV27 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J"
R803 12919471T "CARBON RESISTOR, SB 1/2W 470 OHM J" RV28 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J"
R804 12919689T "CARBON RESISTOR, SB 1/2W 6.8 OHM J" RV29 12368224T "CARBON RESISTOR, SB 1/6W 220K OHM J"
R805 12919821T "CARBON RESISTOR, SB 1/2W 820 OHM J" RV51 12368471T "CARBON RESISTOR, SB 1/6W 470 OHM J"
R807 12919474T "CARBON RESISTOR, SB 1/2W 470K OHM J" RV52 12368470T "CARBON RESISTOR, SB 1/6W 47 OHM J"
R808 12919474T "CARBON RESISTOR, SB 1/2W 470K OHM J" RV53 12368750T "CARBON RESISTOR, SB 1/6W 75 OHM J"
R811 12371433T "METAL RESISTOR, RN 1/2W 43K F" RV54 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J"
R812 12371252T "METAL RESISTOR, RN 1/2W 2.5K F" U111 C1893326B "PCB, MAIN PTNM04 (29KN)FR1=1Y"
R813 12368304T "CARBON RESISTOR, SB 1/6W 300K OHM J" C009 12692103T "PLASTIC CAPACITOR, M 50V 0.01MF J"
R814 12371152T "METAL RESISTOR, RN 1/2W 1.5K F" C014 12692272T "PLASTIC CAPACITOR, M 50V 2700PF J"
R815 12371102T "METAL RESISTOR, RN 1/2W 1KF" C017 12692103T "PLASTIC CAPACITOR, M 50V 0.01MF J"
R816 12371753T "METAL RESISTOR, RN 1/2W 75K F" C025 12692103T "PLASTIC CAPACITOR, M 50V 0.01MF J"
R821 12368223T "CARBON RESISTOR, SB 1/6W 22K OHM J" C047 12693222T "PLASTIC CAPACITOR, M 100V 2200PF J"
R822 12919100T "CARBON RESISTOR, SB 1/2W 10 OHM J" C101 12797100T "CHEMICON, 50V 10MF 85C 5*11"
R831 12368472T "CARBON RESISTOR, SB 1/6W 4.7K OHM J" C103 12793471T "CHEMICON, 10V 470MF 85C 8*12"
R832 12919102T "CARBON RESISTOR, SB 1/2W 1K OHM J" C108 12794221T "CHEMICON, 16V 220MF 85C 8*12"
R833 12919123T "CARBON RESISTOR, SB 1/2W 12K OHM J" C110 12794470T "CHEMICON, 16V 47MF 85C 5*11"
R855 12919561T "CARBON RESISTOR, SB 1/2W 560 OHM J" C111 12797100T "CHEMICON, 50V 10MF 85C 5*11"
R862 12368473T "CARBON RESISTOR, SB 1/6W 47K OHM J" C117 12797479T "CHEMICON, 50V 4.7MF 85C 5*11"
R863 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J" C182 12797479T "CHEMICON, 50V 4.7MF 85C 5*11"
R864 12368471T "CARBON RESISTOR, SB 1/6W 470 OHM J" C183 12797479T "CHEMICON, 50V 4.7MF 85C 5*11"
R865 12368472T "CARBON RESISTOR, SB 1/6W 4.7K OHM J" C184 12797479T "CHEMICON, 50V 4.7MF 85C 5*11"
R872 12368821T "CARBON RESISTOR, SB 1/6W 820 OHM J" C185 12353560T "CERAMIC CAPACITOR, CH 50V 56PF J"
R890 12005825T "SURGE RES(VDE),1/2W 8.2M OHM" C186 12353470T "CERAMIC CAPACITOR, CH 50V 47PF J"
R892 12005335T "R-SURGE, PRC 1/2W 3.3M OHM" C201 12795470T "CHEMICON, 25V 47MF 85C 5*11"
RC01 12368562T "CARBON RESISTOR, SB 1/6W 5.6K OHM J" C311 12794220T "CHEMICON, 16V 22MF 85C 5*11"
RC02 12368752T "CARBON RESISTOR, SB 1/6W 7.5K OHM J" C312 12693102T "PLASTIC CAPACITOR, M 100V 1000PF J"
RC03 12368113T "CARBON RESISTOR, SB 1/6W 11K OHM J" C313 12693102T "PLASTIC CAPACITOR, M 100V 1000PF J"
RC04 12368183T "CARBON RESISTOR, SB 1/6W 18K OHM J" C314 12797100T "CHEMICON, 50V 10MF 85C 5*11"
RC05 12368363T "CARBON RESISTOR, SB 1/6W 36K OHM J" C320 12693104T "PLASTIC CAPACITOR, M 100V 0.1MF J"
RC06 12368114T "CARBON RESISTOR, SB 1/6W 110K OHMJ" C331 12796101T "CHEMICON, 35V 100MF 85C 8*12"
RE01 12368112T "CARBON RESISTOR, SB 1/6W 1.1K OHMJ" C361 12795101T "CHEMICON, 25V 100MF 85C 6.3*11"
RE02 12368271T "CARBON RESISTOR, SB 1/6W 270 OHM J" C363 12693104T "PLASTIC CAPACITOR, M 100V 0.1MF J"
RE03 12368363T "CARBON RESISTOR, SB 1/6W 36K OHM J" C385 12214681T "CERAMIC CAPACITOR, B 500V 680PF K"
RE04 12368822T "CARBON RESISTOR, SB 1/6W 8.2K OHM J" C386 12795471T "CHEMICON, 25V 470MF 85C 10*16"
RE05 12368821T "CARBON RESISTOR, SB 1/6W 820 OHM J" C387 12795101T "CHEMICON, 25V 100MF 85C 6.3*11"
RE06 12368753T "CARBON RESISTOR, SB 1/6W 75K OHM J" C388 12795101T "CHEMICON, 25V 100MF 85C 6.3*11"
RE07 12368271T "CARBON RESISTOR, SB 1/6W 270 OHM J" C407 12693222T "PLASTIC CAPACITOR, M 100V 2200PF J"
RE08 12368153T "CARBON RESISTOR, SB 1/6W 15K OHM J" C408 12436331T "CERAMIC CAPACITOR, SL 50V 330PF J"
RE09 12368242T "CARBON RESISTOR, SB 1/6W 2.4K OHM J" C412 12692103T "PLASTIC CAPACITOR, M 50V 0.01MF J"
RE11 12368104T "CARBON RESISTOR, SB 1/6W 100K OHM J" C413 12797330T "CHEMICON, 50V 33MF 85C 6.3*11"
RE12 12368153T "CARBON RESISTOR, SB 1/6W 15K OHM J" C505 12692103T "PLASTIC CAPACITOR, M 50V 0.01MF J"
RE13 12368564T "CARBON RESISTOR, SB 1/6W 560K OHM J" C506 12353220T "CERAMIC CAPACITOR, CH 50V 22PF J"
RF01 12328183T "METAL RESISTOR, K 1/6W 18K OHM F" C507 12353220T "CERAMIC CAPACITOR, CH 50V 22PF J"
RF02 12328023T "METAL RESISTOR, K 1/6W 10.2K OHM F" C509 12797100T "CHEMICON, 50V 10MF 85C 5*11"
RF03 12328103T "METAL RESISTOR, K 1/6W 10K OHM F" C514 12797478T "CHEMICON, 50V 0.47MF 85C 5*11"
RN01 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" C515 12797478T "CHEMICON, 50V 0.47MF 85C 5*11"
RN02 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" C517 12794101T "CHEMICON, 16V 100MF 85C 6.3*11"
RN05 12368103T "CARBON RESISTOR, SB 1/6W 10K OHM J" C519 12797109T "CHEMI