Text preview for : SAMSUNG chassis S51A.pdf part of SAMSUNG TV CS25D4V3X/XSG TV CS25D4V3X/XSG,CS25D4X3X/TAW
serv.manual
Back to : SAMSUNG chassis S51A.part | Home
COLOR TELEVISION RECEIVER
Chassis : Model: S51A CS25D4V3X/XSG CS25D4X3X/TAW
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions 2. Specifications and IC Data 3. Disassembly and Reassembly 4. Alignment and Adjustment 5. Troubleshooting 6. Exploded View and Parts List 7. Electric Parts List 8. Block Diagram 9. PCB Layout Diagram 10. Wiring Diagram 11. Schematic Diagrams
ELECTRONICS
© Samsung Electronics Co., Ltd. JAN.1999
Printed in Korea 3S51A-2502
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ! ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Samsung Electronics
Specifications and IC Data
2. Specifications and IC Data
2-1 Specifications
T e le v is io n S y s te m :
MO D E L CI CII CX CK CB CS P AL -I (U H F ) P AL -I (V H F /U H F ) P AL -B /G ,S E C AM-B/G
S YS T E M
P AL -B /G ,D /K,S E C AM-B /G ,D /K P AL -B /G P AL -B /G ,D /K,S E C AM-B /G ,D /K,NT4 .4 3,NT 3.58
C han n e ls : BAND
SYSTEM VHF UHF
PAL/SE CAM -B/G,I 2-12 21-69
PAL/SE CAM -D/K 1-13 21-69
SECAM-K1, PAL-D 2-9 13-57
NTSC-M 2-13 14-69
In ter m e diate-F r equ en c ies (MH z ): SYSTEM BAND P icture IF Carrier Sound IF Carrier Color Sub Carrier P ic tu r e T ub e: PAL/SECAM -B/G 38.90 33.40 34.47 PAL/SECAM -D/K,K1 38.90 32.40 34.47 P AL-I 38.90 32.90 34.47 NTSC-M 38.90 34.40 35.32
25 Inch 29 Inch 30 Inch
A59KPR84X A68KVL74X A70QBZ791X Quick start, in-line-gun, Black stripe,90° degree deflection
P o w er R e qu ir e m en ts: AC 1 00 ~ 2 60 V, 50/60H Z or AC 160 ~ 260 V, 5 0/60H Z An tenn a In p u t Im ped an c e : V H F ,U H F : T ele s c op ic dip o le ante nn a(75 u nb alanc ed ty pe ) Sp ea k er Im p ed anc e : 8 , 1 0W + 10 W
Samsung Electronics
2-1
Specifications and IC Data
2-2 IC Line Up
L O C NO H IC 101 IC 20 1 IC 30 1 IC 50 1 IC 60 1 IC 70 1 IC 80 1 IC 80 2 IC 80 3 IC 80 4 IC 90 1 IC 90 2 IC E 0 1 IC N0 1 IC N0 2 IC A0 1 IC A0 2 IC M0 1 IC P 0 1 IC P 0 2 IC P 0 3 IC T0 1 IC T0 2 NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 S pe cification P AP 10 3T T D A88 44 T D A88 43 L A78 45 T D A61 08 T D A72 97 T D A7 266 S T D A98 59 K A3S 12 65R P C 1 23Y 78R 0 5 K A7 630 S ZM5 03AT 24 C 040 455 8 T D A98 08 T D A98 74 H L A7 567 N T D A98 73 H L A75 66 T E A51 14 T D A9 160 A S D A92 88 S AA52 61 24C 0 2 D escription IF P R E -AMP P AL /S E C AM/NTS C /S E C AM-L P AL /NT S C V E R TIC AL D E F L E C T IO N AMP R G B D R IV E AMP S O U ND AMP (10 W/C H ) S O U ND AMP (5W/C H ) AU D IO P R O C E S S O R S MP S IC (12 A) P H O TO C O U P L E R S WITC H ING R E G U L ATO R S W IT C H ING R E G U L ATO R (5,8V ) MIC O M EEPROM EW D R IV E AMP SIF D E T E C TO R NIC AM D E MO D U L ATO R SIF D E T E C TO R A2 D E MO D U L ATO R SIF & FM D E TE C TO R V ID E O S W IT C H P AL /NT S C D E C O D E R PIP V ID E O P R O C E S S T TX -D E C O D E R E E P R O M(T TX P AG E ME MO R Y) TTX MO D U L E PIP MO D U L E NIC AM MO D U L E A2 S TE R E O MO D U L E MO NO R e m arks
2-2
Samsung Electronics
Specifications and IC Data
2-3 Semiconductor Base Diagrams
ELECTROLYTICCONDENSER DIODE
IC TDA4665(Pin 16) TDA837X(Pin 56) Z8933112PSC(Pin 42) X24CO4P(Pin 8) TDA8395(Pin 16) TDA4665(Pin 16)
TRANSISTOR
TRANSISTOR
IC
SAW-FILTER
2SD1651 2SD1650 KSD5072 KSD5071 KSD1711
KSA815-Y KSA539-Y
UPC574J or KA33V
G1962 K2950M K9253M
1
B
C
E
E B C
IC
TRANSISTOR TDA8133 KA7812
TRANSISTOR
KSR1012 KSR1010 KSR2010
IN
G
OUT
E C B
Fig. 2-1 Semiconductor Base Diagrams
Samsung Electronics
2-3
MEMO
2-4
Samsung Electronics
Disassembly and reassembly
3. Disassembly and Reassembly
3-1 Back Cover Removal
1. After removing the 7 screws, pull the cabinet backwards.
Samsung Electronics
3-1
Disassembly and reassembly
3-2 Main Board Removal
3
1 2
11 4 13
8
5 7
12 6 9 10
1. Separate the TBC-wire 2P connector from GT501,GT502. 2. Separate the CRT Assay from the CRT socket. 3. Remove the Anode Cap from the CRT. 4. Separate the D-Coil Connector from CN802. 5. Separate the AC cord from CN801. 6. Separate the DC connector from CN401. 7. Separate the CN501B 8P CRT connector from CN501. 8. Separate the CNA05 5P A/V side connector from CN602. 9. Separate the CNA01 8P CRT connector from CN701. 10. Separate the Focus,Screen Wire from the FBT clamper. 11. Separate the TBC wire 2P, speaker wires from the wire clamper. 12. Separate the CN701, CN602 connector from the wire clamper. 13. Separate the AC cord from the wire clamper. 14. Remove the main board by pulling it with both hands.
3-2
Samsung Electronics
Disassembly and reassembly
3-3 Speaker Removal
1. Remove the speaker by pressing the tension rib.
1. Separate the speaker wires from D-coil (located on the bottom to the right side).
7
2. Remove the screws.
Samsung Electronics
3-3
Disassembly and reassembly
3-4 CRT Removal
1. Remove the 4 nuts mounting the CRT to the front cabinet. Pull the CRT backwards. 2. Caution: Because of the high vacuum and large surface area of the picture tube, be careful while handling it: (1) Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure. Fractures of the glass may cause an implosion.
3-4
Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments
4-1 Preadjustment
4-1-1 Factory Mode
1. Do not attempt these adjustments in the Video Mode. 2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced. 3. Do not tamper with the ÒAdjustmentÓ screen of the Factory Mode menu. This screen is intended only for factory use.
4-1-3 When CRT Is Replaced
1. Make the following adjustments AFTER setting up after setting up purity and convergence : White Balance Sub-Brightness, Sub-Contrast Vertical Center Vertical Size Horizontal Size Fail Safe (This adjustment must be the last step).
4-1-2 When EEPROM (IC902) Is Replaced
1. When IC902 is replaced all adjustment data revert to initial values. It is necessary to re-program this data. 2. After IC902 is replaced, warm up the TV for 10 seconds.
4-2 Factory/Service Mode
4-2-1 Procedure for the "Adjustment" Mode
1. This mode uses the standard remote control. The Service Mode is activated by entering the following remote-control sequence : (1) STAND-BY® DISPLAY® MENU® MUTE ®POWER ON. 2. The ÒSERVICE (FACTORY)Ó message will be displayed. The Service Mode has four components: Adjustment, Test Pattern, Option Bytes and Reset. 3. Access the Adjustment Mode by pressing the ÒVOLUMEÓ keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHANNEL keys (v ,w). 4. Selection sequences for the PAL/NTSC system: DOWN or UP key: AGC£VCO£SBT£SCT£SCR£SC£RG£ BG£CDL£STT£PDL£VOL£PSL£PVS£ PVA£PHS£PEW£PEP£PEC£PET£VSC£ TSC£SA£QEW£PCT£PTT£PHM£PVP£ NVP£PHP£NSR£FFI£AGC. 5. The VOLUME keys increase or decrease the adjustment values (stored in the non-volatile memory) when Adjustment Mode is cancelled. 6. Cancel the Adjustment Mode by re-pressing the ÒHIDDENÓ or ÒPower OFF/ONÓ keys.
Samsung Electronics
4-1
Alignment and Adjustments
4-2-2 Main Adjustment Parameters
OSD AGC VC O SBT SCT SC R SC RG BG C DL STT P DL VOL P SL PVS PVA P HS PEW PEP PEC PET VSC TSC SA QE W PCT PTT P HM PVP NVP P HP NSR FFI AUTO GAIN CONTROL VOLTAGE CONTROLLED OSCILLATOR SUB BRIGHT SUB CONTRAST SUB COLOR S-CORRECTION RED DRIVE GAIN BLUE DRIVE GAIN CATHODE DRIVE LEVEL SUB TINT PAL DELAYTIM E VOLUME LEVEL PAL VERTICAL SLOP PAL VERTICAL SHIFT PAL VERTICAL AM PLITUDE PAL HORIZONTAL SHIFT PAL EW-WIDTH PAL EW-PARABOLA PAL EW-CORNER PARABOLA PAL EW-TRAPEZIUM VERTICAL SCROLL TTX SUB CONTRAST SEPARATION ADJUSTM ENT Q EW-WIDTH PIP CONTRAST PIP TINT OVE PIP HORIZENTAL M PIP PAL VERTICAL POSITION PIP NTSC VERTICAL POSITION PIP HORIZENTAL POSITION NTSC SUB COLOR FAST FILTER IF-PLL FUNCTION RANGE 0 ~ 63 0 ~127 0 ~ 23 0 ~ 23 0 ~ 23 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 7 0 ~ 13 0 ~ 15 0 ~100 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 14 0 ~ 15 0 ~ 15 0 ~ 63 0 ~ 15 0 ~63 0 ~ 63 0 ~ 63 0 ~ 23 0 ~ 1
4-2
Samsung Electronics
Alignment and Adjustments
FACTORY MODE VALUE OSD 2 (C H ) AG C VC O SBT SCT SC R SC RG BG C DL STT 18 (F IXE D ) 80 (F IXE D ) 7 16 5 (F IXE D ) 11 (F IXE D ) 31 31 7 (F IXE D ) 10 (F IXE D ) INITIAL OSD PDL VOL P SL P VS P VA PHS PEW PEP PEC PET V SC INITIAL 0 (F IXE D ) 25 (F IXE D ) 31 (F IXE D ) 31 31 40 38 22 22 30 31 (F IXE D ) OSD TSC SA QEW PCT PTT PHM P VP NVP PHP NSR FFI INITIAL 40 2 5(F IX E D ) 5 7(F IX E D ) 3 1(F IX E D ) 8(F IX E D ) 3 1(F IX E D ) 3 1(F IX E D ) 4 2(F IX E D ) 3(F IX E D ) 1:INDIA,0:OTHERS
4-2-3 Test Pattern
1. This mode can be used during servicing, or for confirming that the convergence and purity adjustments are correct. 2. Access the Test Pattern parameters by pressing a CHANNEL keys (v ,w) while the Service Mode is on. The cursor will move to the test pattern. Press the VOLUME keys. On-screen display:
· RED · GREEN · BLUE · WHITE
3. AGING Mode (Reference Only) This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the factory by twice pressing the ÒHIDDEN Ò key. Even if the TV power is cut off, the Aging Mode is not cancelled, The AGING mode is cancelled by repressing the ÒHIDDENÓ or any key on the front pannel.
Samsung Electronics
4-3
Alignment and Adjustments
4-2-4 Option Byte Table
System : cs Normal / Zoom / 16:9 Pip : on Jack : RCA Audio : Nicam One Chip : TDA8844 Language : English Text : ON X-prot : OFF S-sytem : B/G
O P T IO N OSD CS SY ST E M C S-C H INA C B / CII C K / CX NO R MAL / ZOOM / 16 :9 P L U S / ZOOM NO R MAL / ZOOM P L U S / NORMAL PLUS / NORMAL/ ZOOM / 16:9 PIP ON OFF SC AR T RCA NIC AM AU D IO S TE R E O L -S TE R E O MO NO O NE C H IP TD A8 84 4 TD A8 84 2 PIP U SE D PIP D E L E TE D 21P IN JAC K U SE D R C A JAC K U S E D NIC AM MO D U L E U S E D A2 MO D U L E U S E D MO NO & L INE ST E R E O U SE D MO NO U S E D C R T (MO R E T H AN 22 -INC H ) U S E D C R T (MO R E T H AN 21 -INC H ) U S E D S E L E C T A MO D E AV AIL AB L E TO AD JU S T P -SIZE NO T E MU L TI S YS TE M WITH O U T S E C AM SY S TE M P AL -B /G & P AL -I P AL / SEC AM B/G ,D / K
JAC K
4-4
Samsung Electronics
Alignment and Adjustments
O P T IO N
OSD ENGLISH AR AB P E R SIAN F R ANCH C H INA IND O NE SIA
NO T E E NG L IS H O NL Y E NG L IS H / AR ABIAN E NG L IS H / P E R SIAN E NG L IS H / F R E NC H E NG L IS H / C H INE S E E NG L IS H / IND O NE SIAN E NG L ISH / MAL AYS IAN E NG L ISH / T H AI E NG L ISH / V IE TNAME S E E NG L ISH / AR AB IAN / F R E NC H E NG L ISH / AR AB IAN / P E R SIAN / F R E NC H / C H INE S E / IND O NE SIAN / MAL AYS IAN/ THAI / V IE T NAM TTX U S E D TTX D E L E TE D X -R AY P R O TE C TO R U SE D NO X-R AY P R O TE C T O R F U NC T IO N 1.TH E SO U ND SY ST E M C O ME S F IR S T IN AU TO S E AR C H 2.SO U ND SY ST E M IN F AC TO R Y MO D E R ESE T 3."AU TO " MO D E IS S H O W N O NL Y W H E N L -ST E R E O OR MO NO IS SE L E C TE D IN THE AU D IO MO D E .
L ANG U AG E
MAL AYS IA TH AI VIE TNAM AR AB / F RANCH MU L TI ON OFF ON OFF B/G I
TE XT
X -P R O T
S -SY S TE M
D/K M AU T O
Samsung Electronics
4-5
Alignment and Adjustments
4-2-5 RESET
The Reset Mode is used during factory inspection. Function Reset: 1. 2. Channels Language Add/Erase Basic (English)
4-3 Other Adjustments
4-3-1 General
1. Usually, a color TV needs only slight touchup adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, perform the purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isolation transformer.
4-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 30 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
4-6
Samsung Electronics
Alignment and Adjustments
4-3-3 High Voltage Check
CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply must be set to +130 volts (Full color bar input and normal picture level).
4-3-6 Purity Adjustment
1. Warm up the receiver for at least 20 minutes. 2. Plug in the CRT deflection yoke and tighten the clamp screw. 3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-2. 4. Input a black and white signal. 5. Fully demagnetize the receiver by applying an external degaussing coil. 6. Turn the CONTRAST and BRIGHTNESS controls to maximum. 7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-3). 8. Tighten the convergence yoke. 9. Slowly move the deflection yoke forward, and adjust for the best overall green screen. 10. Temporarily tighten the deflection yoke. 11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke.
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage should not exceed 33KV. 4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 33KV under any conditions.
4-3-4 FOCUS Adjustment
1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
4-3-5 Screen Adjustment
1. Connect CRT socket pin GK, BK, RK to an oscilloscope probe. 2. Input a gray scale pattern. (Use a pattern generator, PM5518) 3. Use the Picture mode for the STANDARD picture. 4. Adjust the Screen VR (on the FBT) so that the _ voltage on the oscilloscope becomes 130+2.5V (See Fig. 4-1).
_ 130 + 2.5V
GND
Fig. 4-1 Samsung Electronics 4-7
Alignment and Adjustments
4 Pole Magnet 6 Pole Magnet Clamper Screw 2 Pole Magnet
2 POLE PURITY
YOKE CLAMP SCREW 6 POLE CONVERGENCE 4 POLE CONVERGENCE
Fig. 4-2 Convergence Magnet Assembly
Vertical Green Belt
31m/m
Fig. 4-3 Center Convergence Adjustment
4-3-7 White Balance Adjustment
(a) Set up 1. Warm up the TV for at least 30 minutes in the White Pattern. 2. Input a Toshiba pattern. (b) High-Light Adjustment 2 Set SCT to 50 ± 5 fL in the Factory Service Mode with using CA100. (See Fig. 4-4 x) (c) Low-Light Adjustment Fig. 4-4 Set SBT to 1.2 ± 0.2 fL in the Factory Service Mode with using CA100. (See Fig. 4-4 )
1
4-8
Samsung Electronics
Alignment and Adjustments
4-3-8 Center Convergence Adjustment
1. Warm up the receiver for at least 20 minutes. 2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen. 3. Adjust the Brightness and Contrast controls for a well defined picture. 4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them. Superimpose the red and the blue vertical lines in the center area of the screen. 5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen. 6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.) 7. Repeat adjustments 2~6, if necessary. 8. Since the 4-pole magnets and 6-pole magnets interact, the dot movement is complex (Fig. 4-5).
BLUE
RED
RED/BLUE
GREEN
BLUE RED
RED/BLUE GREEN
4-Pole Magnet Movement
6-Pole Magnet Movement
Fig. 4-5 Center Convergence Adjustment
4-3-9 RF AGC Adjustment
1. Tune to the strongest local station. 2. Enter the Factory Service Mode to make adjustments. 3. Adjust the AGC control untill noise(snow) disappears from the screen.
Samsung Electronics
4-9
Alignment and Adjustments
4-3-10 Geometry Adjustment
1. Inp u t a lio n h ea d p atter n. 2. Adju s t P V S s o that th e p ic tu r e is v er tic a lly c en ter ed . 3. Adju s t w ith P V A s o that th e top a nd bo tto m m a r gin s of th e p ic tu r e a r e 4 . 4. Adju s t P H S s o tha t th e p ic tur e is ho r iz o n ta lly c en ter ed . 5. Adju s t w ith P E W s o th at the le ft and r ig h t m a r gin s of th e p ic tu r e a r e 5 . 4
5
5 4
6. Inpu t a cro ssha tch p atte rn. 7. Adju s t P E P , P E C , P E T for vertica l linearity.
4-10
Samsung Electronics
Troubleshooting
5. Troubleshooting
5-1 No Video (Raster On, No Sound)
Measure the Voltage of each of, 8 pins of TU101
No
Check/Replace TU101, HC101
Yes
Check IC901 Pins 39, 40 Yes
No
Check/Replace IC901,IC201,IC902 ,IC701, Audio Module
See "No Video" (Sound OK)
See "No Sound" (Video OK)
Samsung Electronics
5-1
Troubleshooting
5-2 No Power
Check the 130V, 12.7V B+ Lines
No
Check/Replace IC801, D802
Yes
Check IC804 Pin 9 (5V)
No
Check/Replace IC804(KA7630),DZ905,DZ804
Yes
Check IC901 Pin 8 (4V).
No
Check/Replace IC901
Yes
Check IC901 Pin 18 ; Stand-by : 0V Normal : 5V
No
Check/Replace IC901(m-com)
Yes
Check IC201, Pin 40 (H-out)
No
Check/Replace IC201, Q402, Q403
Yes
Check Q402, Q403
No
Check/Replace DZ805, IC802
5-2
Samsung Electronics
Troubleshooting
5-3 No Video (Sound OK)
Check IC201 Pin 12,37 (8V)
No
Check/Replace IC804 KA7630
Yes
Check IC201 Pin 6 (CVBS) 2Vp-p Yes
No
Check/Replace IC201
Check IC201 Pins 19, 20, 21 (R/G/B-OUT)
No
Yes
Check IC202 pin 27 (Y-IN)
No
Check/Replace IC201,D205,DZ204
Yes
Check IC501, on the CRT PCB
No
Check/Replace IC501
Yes
Check/Replace R505 (HEATER 6.3Vrms) CRT, V999
Samsung Electronics
5-3
Troubleshooting
5-4 No Sound (Video OK)
CHECK IC701 Pin 3,5
No
CHECK/REPLACE Sound Module (MD701)
Yes
CHECK IC701 Pin 15,18
No
CHECK/REPLACE IC701, C712, C719
Yes
CHECK IC601 Pin 1 2 14 15 Sound output Yes CHECK/REPLACE A/V Front Assembly.
No
CHECK/REPLACE IC601, R601, R602
5-5 Power OFF/ON (Repeatedly)
CHECK Q403 COLLECTOR H-PULSE YES NO SEE " NO-POWER"
CHE CK IC901 PIN26(H-SYNC ) YES
NO
CHE CK/REPLACE IC901,Q907,C913 DZ402
CHE CK IC301 PIN7(V-BLANK) NO
YES
CHE CK/REPLACE Q301,Q302,D304
CHECK PIN6(+16.5V) PIN1(-14V) YES CHECK/RE PLACE IC301,IC201
NO
CHE CK/REPLACE R409,R413,D407,D410 DZ302,DZ303
5-4
Samsung Electronics
Troubleshooting
5-6 SMPS (Power Supply) Does Not Function
(1) W he n F 802 is op en : C he ck/Replace F 8 02 , IC 80 1 , D 80 2. (2) W he n F 802 is okay, but SMP S doe s n ot fu nction: C he ck/Replace D Z80 1 , D Z8 08 , IC 80 2 , D Z8 05 . (3) O the rs: S ee "5. Tro ublesh ooting"
Samsung Electronics
5-5
Exploded View & Parts List
6. Exploded View & Parts List
6-1 CS25D4V3X/XSG
No
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 2 2-1 2-2 3 3-1 4
Code No
AA91-10387E AA64-31269F AA64-70011D AA64-10782C AA61-60003J AA65-30105A AA61-40113A 3001-001072 6002-000514 AA64-10783A 6002-000514 AA64-40506A AA64-40505A 6002-000514 AA03-10032E AA65-30113A AA60-10050Q AA64-31270C AA60-10050T AA61-20284A
Description
ASSY-CABINET,FRONT CABINET-FRONT BADGE-BRAND KNOB-POWER SPRING-CS CLAMP-WIRE STOPPER-PCB SPEAKER SCREW-TAPPING KNOB-CONTROL SCREW-TAPPING INDICATOR-LED WINDOW-RMC SCREW-TAPPING CRT-COLOR CLAMP-D,COIL SCREW-ASSY CABINET-BACK SCREW-TAPPING HOLDER
Specification
-,CS-25D4V,(SPK) DG703P EGN TVI, -,CS-25D4V,DG703P EGN TVI,HIPS,HB,BLK AL,SS R2000 25,GOLD,L60,-,-,-,254,294,299D,M/S,ABS,HB,G367 -,SUS304,0.5,OD6,H12,N7,-,-,NYLON 66,V2,NTR,15MM,ALL MODEL 501H,HIPS,NTR,HB,-,5W,16ohm,90dB,180Hz RH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,254,294,294D,G3676,ABS,HB,GR RH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,294,299D,-,ACRYL,HB,CLR,-,294D,-,ABS,HB,LG41338,RH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,A59KPR84X01(M),+200mG,25,11 NYLON 66,V2,BLK,TVI 25~29,-,WC,HH,+,M5,L26.5,SWRCH18A,ZPC( -,254D,-,HIPS,HB,G3119,-,RH,+,2S,M4,L20,ZPC(BLK),SWRCH1 -,P-CORD,PP,VO,BLK,KE-002
Q'ty
1 1 1 1 1 1 1 2 4 1 1 1 1 1 1 4 4 1 4 1
Remark
Samsung Electronics
6-1
Electric Parts List
7. Electric Parts List
7-1 CS25D4X3X/TAW (CS25D4V3X AND CS25D4X3X Dissimilar Parts)
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-PCB,MAIN(OPT)
BUYER : TAWIL * C209 CNP01 CNT01 CNT02 CNT03 AA94-00294AASSY-PCB,MAIN(OPT);CS25D4X3X/TAW,S51A,LEBANON,2202-002037 3711-002704 3711-002702 3711-002703 3711-002705 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. CONNECTOR-HEADER;NOWALL,6P,1R,2.5mm,ANGLE,SN CONNECTOR-HEADER;NOWALL,4P,1R,2.5mm,ANGLE,SN CONNECTOR-HEADER;NOWALL,5P,1R,2.5mm,ANGLE,SN CONNECTOR-HEADER;NOWALL,7P,1R,2.5mm,ANGLE,SN
ASSY-PCB,TTX
* CT01 CT02 CT04 CT05 CT07 CT08 CT09 CT10 CT11 CT12 CT13 CT14 CT15 CT16 CT17 DT01 DZT01 H001 ICT01 ICT02 ICT03 L201 LT01 QT01 QT02 QT03 QT04 QT05 QT06 QT07 RT01 RT02 RT03 RT04 RT05 RT06 RT07 RT08 RT11 RT12 RT13 RT14 RT15 RT17 RT18 RT20 RT21 RT22 AA95-90035J ASSY-PCB,TTX;-,-,S51A,PAL,-,2401-000242 C-AL;100uF,20%,10V,GP,TP,5x11,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2201-000193 C-CERAMIC,DISC;10pF,0.3pF,50V,CH,TP,5x3,5 2201-000193 C-CERAMIC,DISC;10pF,0.3pF,50V,CH,TP,5x3,5 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5 2401-000404 C-AL;10uF,20%,16V,BP,TP,5x11,5 2401-000404 C-AL;10uF,20%,16V,BP,TP,5x11,5 2401-000404 C-AL;10uF,20%,16V,BP,TP,5x11,5 2401-000242 C-AL;100uF,20%,10V,GP,TP,5x11,5 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0403-000355 DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500mW AA61-10068ABRACKET-PCB;-,M2160,SPTE,T0.3,-,-,1204-001486 IC-PAL DECODER;SAA5261/223,DIP,52P,600MIL,PLASTIC,5V 1103-001107 IC-EEPROM;24C020,2Kx1BIT,DIP,8P,300MIL,1 1203-000641 IC-RESET;7442,TO-92,3P,-,PLASTIC,-0.3/7 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1202001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,2001-000857 R-CARBON;560OHM,5%,1/8W,AA,TP,2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000800 R-CARBON;5.1KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,-
RT23 RT24 RT25 RT26 RT27 RT28 RT29 RT30 RT31 RT32 RT33 RT34 RT35 RT36 RT37 RT38 RT39 RT40 RT42 XT01
2001-000780 2001-000857 2001-000429 2001-000780 2001-000857 2001-000429 2001-000780 2001-000857 2001-000429 2001-000969 2001-000290 2001-000429 2001-000969 2001-000290 2001-000429 2001-000969 2001-000290 2001-000429 2001-000568 2801-003433
R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;560OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;560OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;560OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;27OHM,5%,1/8W,AA,TP,CRYSTAL-UNIT;12MHz,30ppm,28-AAA,30pF,30ohm,
REMOCON
* AA59-10116AREMOCON;-,TM59,SS,SZM503AT,29,-,-,L/GR
ASSY-CRT
!
AA03-10032MCRT-COLOR;-,A59KPR84X01(MB),+380mG,25,1
ASSY-CABINET;CS25D4X3X/TAW
* AA91-10387F ASSY-CABINET,FRONT;-,CS-25D4T,(SPK) AA64-31269HCABINET-FRONT;-,CS-25D4T,DG703P EGB TVI
Samsung Electronics
7-1
Electric Parts List
7-2 CS25D4V3X/XSG Parts List
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-PCB,MAIN(OPT)
BUYER : SGE * C102 C103 C104 C105 C106 C107 C109 C110 C111 C207 C210 C211 C213 C214 C215 C216 C217 C218 C219 C220 C221 C222 C223 C224 C225 C226 C227 C228 C229 C230 C231 C232 C233 C234 C235 C236 C237 C238 C239 C240 C241 C242 C243 C244 C245 C301 C302 C303 C304 C305 C306 C307 C308 C309 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 AA94-00230AASSY-PCB,MAIN(OPT);CS25D4V3X/XSG,S51A,U.A.E,2401-002594 2202-002037 2202-002037 2202-002037 2401-001082 2401-000914 2202-000796 2202-000796 2202-002037 2401-001026 2306-000122 2401-002619 2301-000224 2401-000660 2305-000412 2401-001840 2305-000665 2305-000411 2401-002144 2401-000302 2305-000289 2305-000412 2202-002037 2202-002037 2202-002037 2401-000480 2201-000986 2201-000273 2301-000356 2301-000192 2202-000183 2202-000796 2309-000138 2305-000289 2202-000849 2202-002037 2305-000665 2301-000383 2301-000445 2401-001840 2401-000603 2202-000806 2401-000603 2301-000224 2305-000665 2301-000254 2401-000360 2201-000259 2305-000285 2305-001011 2305-000149 2401-000360 2401-000480 2401-001840 2401-000901 2201-000291 2401-002268 2306-000272 2201-000984 2305-000382 2201-000551 2401-001397 2305-000178 2201-000599 2401-000302 2306-000329 2306-000322 C-AL;220uF,20%,16V,GP,TP,8x11.5,5 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-AL;330nF,20%,50V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-AL;3.3UF,20%,50V,GP,TP,5X11,5 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm, C-AL;47uF,20%,25V,GP,TP,5x11,5 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C-AL;2.2uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C-FILM,MPEF;470nF,5%,50V,TP,7.3x4.8x5.5mm, C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-AL;10uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,DISC;12pF,5%,50V,NPO,TP,5x3mm,2.5mm C-CERAMIC,DISC;18pF,5%,50V,CH,TP,5x3mm,5 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP,3.5X1.9MM, C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,C-FILM,PE-PPF;100nF,5%,50V,TP,20x16x8.5,7.5m C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3.5x1.9,C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP,3.5x19,C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C-FILM,PEF;39nF,5%,50V,TP,7.5x3.5x6.5mm,5 C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-CERAMIC,DISC;180pF,10%,500V,Y5P,TP,6x4,5 C-FILM,MPEF;220nF,5%,100V,TP,20x18x11.5,15 C-FILM,MPEF;22nF,5%,100V,TP,3.5x12.5x7.5mm C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5,5 C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;22uF,20%,160V,GP,TP,10x20,5 C-CERAMIC,DISC;1nF,10%,500V,Y5P,TP,8.5x5MM,5 C-AL;2.2uF,20%,250V,LZ,TP,8X11,5 C-FILM,MPPF;820nF,5%,400V,BK,29x25.5x18.5, C-CERAMIC,DISC;680pF,10%,2KV,Y5P,TP,11x6,7.5m C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mm C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5 C-AL;470uF,20%,25V,GP,TP,10x16,5 C-FILM,MPEF;10nF,5%,100V,TP,-,5mm C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-FILM,MPPF;7nF,3%,1.6KV,TP,28.5x18.5x11mm C-FILM,MPPF;12nF,5%,1.6KV,TP,29x20.5x13,20
C416 C417 C418 C419 C421 C422 C423 C424 C425 C427 C504 C506 C510 C520 C530 C601 C602 C603 C604 C605 C606 C607 C701 C702 C703 C704 C705 C707 C709 C710 C711 C712 C713 C714 C715 C716 C717 C718 C719 C720 C721 C722 C723 C725 C727 C730 C731 C732 C733 C801 C802 C804 C805 C806 C807 C808 C809 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826
2301-001258 2306-000102 2201-000556 2401-001397 2401-002619 2306-000122 2201-000556 2401-001527 2305-000154 2201-002041 2202-000862 2301-000213 2401-000430 2401-001232 2201-002063 2401-001914 2301-000445 2401-001333 2301-000192 2401-001914 2301-000445 2401-001998 2202-002037 2401-002144 2202-000243 2202-002037 2305-000289 2401-000302 2306-000122 2401-000302 2401-002235 2401-000480 2301-000247 2301-000289 2401-000647 2401-000647 2301-000289 2301-000247 2401-000480 2401-002235 2301-000175 2305-000289 2301-000175 2305-000289 2305-000289 2202-000231 2202-000231 2202-000231 2202-000231 2306-000321 2306-000321 2201-000332 2201-000332 2401-001426 2303-000163 2401-002292 2301-000224 2301-000310 2201-002002 2201-002002 2201-000683 2401-003026 2401-000293 2201-000599 2401-000722 2201-000599 2401-000722 2301-000192 2201-000599 2401-001840 2305-000289 2306-000122 2401-001840
C-FILM,PPF;39nF,5%,400V,TP,19.5x9x15,7.5 C-FILM,MPPF;1.2uF,5%,250V,TP,29*31*14.5,20 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-AL;470uF,20%,25V,GP,TP,10x16,5 C-AL;47uF,20%,25V,GP,TP,5x11,5 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm, C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-AL;47uF,20%,250V,HR,TP,13x25mm,5m C-FILM,MPEF;100nF,5%,400V,TP,21.5x6.5x11.5 C-CERAMIC,DISC;820pF,10%,2KV,Y5P,TP,12x6,7.5m C-CERAMIC,MLC-AXIAL;390pF,10%,50V,Y5P,TP,3.5x1.9,C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5 C-AL;10uF,20%,250V,GP,TP,10x16mm,5m C-AL;4.7uF,20%,250V,GP,TP,10x12.5,5 C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,16x5,7 C-AL;1uF,20%,50V,BP,TP,5x11,5 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;470nF,20%,50V,GP,TP,5x11,5 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-AL;1uF,20%,50V,BP,TP,5x11,5 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-AL;47uF,20%,16V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;33pF,5%,50V,SL,TP,3.5x19,C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm, C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-AL;10uF,20%,50V,GP,TP,5x11,5 C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5m C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5 C-AL;2.2uF,20%,50V,BP,TP,5x11,5 C-AL;2.2uF,20%,50V,BP,TP,5x11,5 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5 C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5m C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-FILM,PEF;15nF,5%,50V,TP,7.1x3.5x13mm,5m C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-FILM,PEF;15nF,5%,50V,TP,7.1x3.5x13mm,5m C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-FILM,MPPF;470NF,5%,275V,TP,-,22.5 C-FILM,MPPF;470NF,5%,275V,TP,-,22.5 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-AL;470uF,20%,400V,GP,-,35x45mm,10 C-FILM,PPF;2.2nF,5%,800V,TP,15x13x8.5,7.5 C-AL;47uF,20%,25V,WT,TP,8X11,5 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,5 C-CERAMIC,DISC;4700pF,20%,400V,+20%~-55%,TP,2 C-CERAMIC,DISC;4700pF,20%,400V,+20%~-55%,TP,2 C-CERAMIC,DISC;850pF,10%,1KV,Y5P,TP,10x5,5 C-AL;330uF,20%,200V,GP,ST,22x35,10 C-AL;100uF,+30-10%,200V,GP,TP,16x25 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm, C-AL;100uF,20%,16V,GP,TP,6.3x11,5
7-2
Samsung Electronics
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
C827 C828 C829 C830 C831 C832 C833 C835 C901 C902 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 C921 C922 C923 C924 C925 C926 C927 C928 CE01 CE02 CE03 CN501B CN601 CN802 CW701 CW901 D101 D201 D202 D203 D204 D205 D209 D210 D217 D301 D302 D303 D304 D401 D402 D403 D404 D406 D407 D410 D507 D508 D509 D520 D601 D602 D701 D801 D802 D803 D804 D805 D806
2401-002235 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm 2401-000493 C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2401-000611 C-AL;1uF,20%,50V,WT,TP,5x11,5 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5 2401-002286 C-AL;470uF,20%,16V,WT,TP,10x12.5,5 2201-000234 C-CERAMIC,DISC;150pF,5%,50V,CH,TP,9.5x3,5 2301-000108 C-FILM,PEF;1.5nF,5%,50V,TP,6.5x3.0x5.5mm, 2201-000119 C-CERAMIC,DISC;100nF,+80-20%,50V,Y5V,TP,8x3.5 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,2202-000121 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP,1.9x3.5,2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5 2201-000257 C-CERAMIC,DISC;16pF,5%,50V,CH,TP,5x3,5 2201-000483 C-CERAMIC,DISC;33pF,5%,50V,CH,TP,5x3,5 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3.5X1.9MM,2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V,TP,2.2x3. 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5 2401-002597 C-AL;220uF,20%,35V,GP,TP,10x12.5,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2305-000470 C-FILM,MPEF;68nF,5%,100V,TP,-,5mm AA39-20604ALEAD CONNECTOR-ASSY;-,YBNH250-9,YBNH05/04,5/4P,50 3711-002643 CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGHT,SN AA27-20004J COIL-DEGAUSSING;-,25,14.5ohm,50T,L2600,E 2503-000161 C-NETWORK;330pFx8,20%,50V,MCCB1H331MX8YT 2503-000156 C-NETWORK;100pFx4,20%,50V 0401-001024 DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-000216 DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-204 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-001012 DIODE-RECTIFIER;FMP-3FU,1500V,5A,TO-3PF 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-000216 DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-204 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41,TP 0402-001160 DIODE-BRIDGE;D5SB60,600V,2.8A,SIP-4,ST 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-000231 DIODE-RECTIFIER;FMG-G26S,600V,4A,TO-220F,ST 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TP
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
D807 D808 D809 D810 D813 D901 D902 D903 D904 D905 D906 D907 DE01 DV801 DV802 DZ201 DZ202 DZ203 DZ204 DZ205 DZ206 DZ210 DZ302 DZ303 DZ304 DZ305 DZ306 DZ402 DZ403 DZ505 DZ601 DZ602 DZ603 DZ604 DZ701 DZ702 DZ703 DZ704 DZ705 DZ801 DZ802 DZ803 DZ805 DZ807 DZ808 DZ901 DZ904 DZ905 DZ906 F801 F801A F801B F802 F803 GT804A HC101 IC201 IC301 IC501 IC601 IC701 IC801 IC802 IC803 IC804 IC901 IC902 ICE01 JA701 L101 L102 L103 L202 L203 L205 L206 L207
0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,200MA,DO-35,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 1405-000187 VARISTOR;750V,1250A,12.5x7mm,TP 1405-000187 VARISTOR;750V,1250A,12.5x7mm,TP 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW, 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW, 0403-000298 DIODE-ZENER;MTZ6.8C,6.8V,6.66-7.01V,500mW, 0403-000662 DIODE-ZENER;MTZ3.0B,3.0V,3.01-3.22V,500mW, 0403-000551 DIODE-ZENER;MTZ3.9B,3.9V,3.89-4.16V,500mW, 0403-000294 DIODE-ZENER;MTZ4.7B,4.7V,4.55-4.80V,500mW, 0403-000659 DIODE-ZENER;MTZ2.0A,2V,1.88-2.10V,500mW,DO 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000494 DIODE-ZENER;MTZ39,39V,35.36-37.2V,500mW,DO 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TP 0403-000300 DIODE-ZENER;MTZ8.2B,8.2V,7.78-8.19V,500mW, 0403-000698 DIODE-ZENER;TZP12A,12V,11.4-12.6V,1W,DO-41 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW, 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000300 DIODE-ZENER;MTZ8.2B,8.2V,7.78-8.19V,500mW, 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 1203-001217 IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL,PLASTIC,2 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 0403-000562 DIODE-ZENER;MTZ7.5B,7.5V,7.07-7.45V,500mW, 1203-000451 IC-VOLTAGE REGULATOR;33,TO-92,3P,-,PLASTIC,31/35V,2 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW, 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 3601-000281 FUSE-FERRULE;250V,4A,TL,GLASS,5.2x20mm 3602-000114 FUSE-HOLDER;-,-,30mohm 3602-000114 FUSE-HOLDER;-,-,30mohm 3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mm 3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mm AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,500,1617#22 AA13-20004WIC-HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TP 0904-001294 IC-BUS CONTROLLER; 1204-000517 IC-VERTIVAL DEF.;LA7845,SIP,7P,-,PLASTIC,40V,11 1201-001330 IC-VIDEO AMP;6108,ZSIP,9P,-,SINGLE,-,PLASTI 1201-001064 IC-POWER AMP;7297,ZIP,15P,-,DUAL,32dB,PLAST 1204-000473 IC-AUDIO PROCESSOR;TDA9859,DIP,32P,-,PLASTIC,-,-, 1203-001482 IC-PWM CONTROLLER;3S1265R,TO-3P,5P,210,PLASTIC,6 0604-001038 PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST 1203-001006 IC-VOLTAGE REGULATOR;78R05,TO-220F,4P,-,PLASTIC,4.8 1203-000644 IC-POSI.FIXED REG.;7630,SIP,10P,-,PLASTIC,5.1/8V, AA13-00001AIC-MCU;-,Z90365-R4060,16BIT,SDIP,29D9,42P,600MIL,32 1103-001105 IC-EEPROM;24C040,4Kx1BIT,DIP,8P,300MIL,1 1201-000191 IC-OP AMP;4558,DIP,8P,300MIL,DUAL,20V/mV 3722-001333 JACK-RCA;9P,3.2mm,NI,BLK,2701-000326 INDUCTOR-AXIAL;560nH,10%,2.3x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm 2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm
Samsung Electronics
7-3
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
L208 L303 L401 L402 L403 L404 L501 L601 L603 L701 L702 L703 L704 L705 L706 L707 L708 L709 L801 L802 L803 L804 L805 L806 L807 L808 L901 L902 L903 L904 L905 L906 L907 LD901 Q101 Q201 Q202 Q204 Q205 Q206 Q207 Q210 Q301 Q302 ! Q401 ! Q402 ! Q403 Q701 Q702 Q704 Q801 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 QE01 R102 R103 R104 R105 R201 R202 R203 R204 R212 R214 R215 R217 R218 R219 R220 R221
2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm AA27-40003HCOIL-HORIZ,WIDTH;-,2mH,DR15x20,2UEW0.35,ST AA27-30003GCOIL-LINERITY;-,44uH,DR14x15,PI0.2x10,18x33, 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G AA27-40003L COIL-HORIZ,WIDTH;-,1.0mH,DR14x20,2UEW0.45,ST 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm AA29-30002F FILTER-LINE NOISE;-,6mH,2.45A,-,3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 2901-000299 FILTER-EMI ON BOARD;-,6A,UL/CSA,-,9x7.5,TP,2701-001032 INDUCTOR-AXIAL;100uH,10%,5x14mm 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 2701-000189 INDUCTOR-AXIAL;470nH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm 2701-000211 INDUCTOR-AXIAL;68uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm AA96-30001B ASSY-LED,GUIDE;-,AA61-50055A,DL-G5RGA,0501-000245 TR-SMALL SIGNAL;BC548C,NPN,500mW,TO-92,TP,4200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200504-000150 TR-DIGITAL;KSR2010,PNP,300mW,10K,TO-92,TP 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200502-000298 TR-POWER;KSD73,NPN,30W,TO-220,-,120-240 0502-001007 TR-POWER;KSC2073-H2,NPN,25W,TO-220,ST,6 0502-001136 TR-POWER;KSD5703,NPN,70W,TO-3PF,ST,80501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1200501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,-,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1202001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,2001-000674 R-CARBON;360OHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP,2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,2001-000343 R-CARBON;130OHM,5%,1/8W,AA,TP,2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,-
R222 R223 R224 R225 R226 R230 R231 R232 R233 R234 R235 R237 R238 R239 R240 R241 R243 R246 R247 R248 R249 R250 R251 R252 R253 R255 R256 R257 R258 R259 R260 R261 R262 R301 R302 R303 R304 R305 R306 R308 R309 R310 R311 R312 R313 R314 R315 R316 R317 R404 R405 R406 R407 R409 R410 R411 R412 R413 R414 R415 R417 R418 R419 R420 R421 R422 R424 R425 R428 R429 R430 R501 R502 R503 R505 R506 R507
2701-000142 2001-000617 2001-000429 2001-001026 2001-000793 2001-000331 2001-000734 2001-000241 2001-000780 2001-000780 2001-000780 2001-000007 2001-001110 2001-000008 2001-001125 2001-000429 2001-000232 2001-000273 2001-000281 2001-000793 2001-000429 2001-000938 2001-000281 2001-000563 2001-000591 2001-000008 2004-001234 2001-000563 2004-001914 2001-000281 2001-001015 2001-000331 2001-001015 2001-001045 2001-001049 2001-000016 2008-000254 2003-002069 2003-002069 2003-002069 2001-000290 2001-000387 2001-000660 2001-000786 2001-000449 2001-000281 2001-000290 2001-000660 2001-000449 2008-001013 2001-001138 2003-002008 2003-001025 2008-000264 2001-001114 2001-000022 2001-000020 2008-000251 2008-000278 2008-000251 2004-001899 2004-001967 2004-001390 2001-001114 2001-001043 2008-001013 2001-001043 2001-001043 2001-001043 2001-001043 2001-001043 2001-000429 2001-000429 2001-000429 2008-000254 2008-000299 2001-000490
INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm R-CARBON;3.9MOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;910OHM,5%,1/8W,AA,TP,R-CARBON;47OHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R-CARBON;1.5KOHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;470OHM,5%,1/8W,AA,TP,R-CARBON;3KOHM,5%,1/8W,AA,TP,R-CARBON(S);240KOHM,5%,1/2W,AA,TP,R-CARBON;15KOHM,5%,1/8W,AA,TP,R-CARBON(S);300KOHM,5%,1/2W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;1.3KOHM,5%,1/8W,AA,TP,R-CARBON;100KOHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;47OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;68OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;27KOHM,5%,1/8W,AA,TP,R-CARBON;3.3KOHM,5%,1/8W,AA,TP,R-CARBON;15KOHM,5%,1/8W,AA,TP,R-METAL;75Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;27KOHM,5%,1/8W,AA,TP,R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mm R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;9.1KOHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;9.1KOHM,5%,1/8W,AA,TP,R-CARBON(S);1.2KOHM,5%,1/2W,AA,TP,R-CARBON(S);1.3KOHM,5%,1/2W,AA,TP,R-CARBON(S);1OHM,5%,1/2W,AA,TP,R-FUSIBLE(S);0.68ohm,5%,2W,AF,TP,3.9x10mm R-METAL OXIDE;470ohm,5%,2W,AF,TP,3.9x10mm R-METAL OXIDE;470ohm,5%,2W,AF,TP,3.9x10mm R-METAL OXIDE;470ohm,5%,2W,AF,TP,3.9x10mm R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;16KOHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,R-CARBON;47KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm R-CARBON(S);390OHM,5%,1/2W,AA,TP,R-METAL OXIDE(S);18Kohm,5%,2W,AF,TP,3.9x10mm R-METAL OXIDE(S);15Kohm,5%,2W,AF,TP,3.9x10mm R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm R-CARBON(S);270OHM,5%,1/2W,AA,TP,R-CARBON(S);33OHM,5%,1/2W,AA,TP,R-CARBON(S);22OHM,5%,1/2W,AA,TP,R-FUSIBLE(S);0.27ohm,10%,2W,AF,TP,3.9x10mm R-FUSIBLE(S);82ohm,5%,2W,AA,TP,3.9x10mm R-FUSIBLE(S);0.27ohm,10%,2W,AF,TP,3.9x10mm R-METAL(S);61.9Kohm,1%,1/2W,AA,TP,2.5x6.5 R-METAL(S);68Kohm,1%,1/2W,AA,TP,2.5x6.5mm R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm R-CARBON(S);270OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON(S);0OHM,5%,1/2W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);0.68ohm,5%,2W,AF,TP,3.9x10mm R-FUSIBLE(S);47ohm,5%,2W,AF,TP,3.9x10mm R-CARBON;200OHM,5%,1/8W,AA,TP,-
7-4
Samsung Electronics
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
R508 R509 R510 R517 R518 R519 R520 R601 R602 R603 R604 R605 R606 R607 R701 R702 R703 R704 R705 R706 R707 R708 R709 R710 R711 R712 R713 R714 R715 R716 R717 R718 R719 R720 R721 R722 R723 R724 R725 R728 R729 R732 R733 R734 R735 R736 R740 R741 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 R826 R901 R902 R903 R904 R905
2001-000490 2001-000490 2002-001009 2002-001009 2002-001009 2002-001009 2001-001062 2008-001002 2008-001002 2001-000472 2001-000331 2001-000429 2001-000472 2001-000331 2001-000281 2001-000281 2001-000515 2001-000515 2001-000281 2001-000281 2001-000515 2001-000515 2001-000969 2001-000628 2001-000429 2001-000539 2001-000969 2001-000429 2001-000969 2001-000660 2001-000539 2001-000969 2001-000527 2001-000387 2001-000786 2001-000449 2001-000387 2001-000786 2001-000969 2001-000281 2001-000281 2001-000449 2001-000969 2001-000969 2001-000969 2001-000660 2701-000114 2701-000114 2002-001011 2003-000994 2003-000994 2001-001150 2001-001150 2003-001023 2001-001178 2002-001011 2002-001013 2003-000782 2003-000462 2001-000429 2001-000449 2004-001889 2004-001983 2001-001153 2001-000290 2001-000273 2008-001047 2008-000271 2001-000290 2008-000264 2001-001125 2001-001153 2001-000290 2001-000290 2001-000066 2004-000218 2004-000218
R-CARBON;200OHM,5%,1/8W,AA,TP,R-CARBON;200OHM,5%,1/8W,AA,TP,R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0 R-CARBON(S);10MOHM,5%,1/2W,AA,TP,R-FUSIBLE(S);0.18ohm,5%,2W,AA,TP,3.9x10mm R-FUSIBLE(S);0.18ohm,5%,2W,AA,TP,3.9x10mm R-CARBON;2.7KOHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;2.7KOHM,5%,1/8W,AA,TP,R-CARBON;12KOHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;220OHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;300OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;24KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,R-CARBON;24KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;22OHM,5%,1/8W,AA,TP,R-CARBON;16KOHM,5%,1/8W,AA,TP,R-CARBON;47KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;16KOHM,5%,1/8W,AA,TP,R-CARBON;47KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;100OHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;75OHM,5%,1/8W,AA,TP,R-CARBON;33KOHM,5%,1/8W,AA,TP,INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm R-COMPOSITION;3.3Mohm,10%,1/2W,AA,TP,3.7x9mm R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x10mm R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x10mm R-CARBON(S);470KOHM,5%,1/2W,AA,TP,R-CARBON(S);470KOHM,5%,1/2W,AA,TP,R-METAL OXIDE(S);120ohm,0.05,2W,AF,TP,3.9x10mm R-CARBON(S);680OHM,5%,1/2W,AA,TP,R-COMPOSITION;3.3Mohm,10%,1/2W,AA,TP,3.7x9mm R-COMPOSITION;4.7Mohm,10%,1/2W,AA,TP,3.7x9mm R-METAL OXIDE(S);7.5Kohm,5%,2W,AA,TP,4x12mm R-METAL OXIDE(S);10Kohm,5%,2W,AA,TP,4x12mm R-CARBON;1KOHM,5%,1/8W,AA,TP,R-CARBON;2.2KOHM,5%,1/8W,AA,TP,R-METAL(S);127Kohm,1%,1/2W,AA,TP,2.5x6.5m R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.4 R-CARBON(S);47OHM,5%,1/2W,AA,TP,R-CARBON;10KOHM,5%,1/8W,AA,TP,R-CARBON;100KOHM,5%,1/8W,AA,TP,R-FUSIBLE(S);68ohm,5%,2W,AF,TP,3.9x10mm R-FUSIBLE(S);3.3ohm,5%,2W,AA,TP,3.9x10mm R-CARBON;10KOHM,5%