Text preview for : KX-TC1230ALW.pdf part of Panasonic KX-TC1230ALW KX-TC1230ALW
Back to : KX-TC1230ALW.rar | Home
Service Manual
TOP NEXT ORDER NO. KM4012741C3
Telephone Equipment
l
KX-TC1230ALW
Cordless Answering System White Version (for Australia)
© 2001 Kyushu Matsushita Electric Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
TOP NEXT
http://schema99.host.sk/
7 TROUBLESHOOTING GUIDE
TOP PREVIOUS NEXT
Cross Reference: Check Power (). Error Message Table (). Check Record (). Check Playback (). Check Sp-phone Transmission (). Check Sp-phone Reception (). Check Battery Charge (). Check Link (). Check Handset Transmission ().
http://schema99.host.sk/
Check Handset Reception (). Check Call ID (). 7.1 Check Power 7.2 Error Message Table 7.3 Check Record 7.4 Check Playback 7.5 Check Sp-phone Transmission 7.6 Check Sp-phone Reception 7.7 Check Battery Charge 7.8 Check Link 7.9 Check Handset Transmission 7.10 Check Handset Reception 7.11 Check Call ID 7.12 Bell Reception
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.1 Check Power
TOP PREVIOUS NEXT
Cross Reference Reset Circuit (). Power Supply Circuit (). NOTE: DSP is IC301.
Cross Reference Charge Circuit (). NOTE: DSP is IC601.
http://schema99.host.sk/
7.2 Error Message Table
TOP PREVIOUS NEXT
NOTE: Flash Memory is IC304. DSP (CPU) is IC301.
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.3 Check Record
TOP PREVIOUS NEXT
Cross Reference: Telephone Line Interface (). Signal Route (). NOTE: Flash Memory is IC304. DSP is IC301.
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.4 Check Playback
TOP PREVIOUS NEXT
Cross Reference: Power Supply Circuit (). NOTE: Flash Memory is IC304. DSP is IC301.
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.5 Check Sp-phone Transmission
TOP PREVIOUS NEXT
Crossn Reference: Telephone Line Interface (). Signal Route (). NOTE: Flash Memory is IC304. DSP is IC301.
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.6 Check Sp-phone Reception
TOP PREVIOUS NEXT
Cross Reference: Telephone Line Interface (). Signal Route (). NOTE: Flash Memory is IC304. DSP is IC301.
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.7 Check Battery Charge
TOP PREVIOUS NEXT
Cross Reference: Charge Circuit (). Power Supply Circuit (). NOTE: DSP is IC301.
Cross Reference: Reset Circuit/Charge Circuit (). NOTE: DSP is IC601.
http://schema99.host.sk/
7.8 Check Link
TOP PREVIOUS NEXT
NOTE : RF IC is IC401 CPU is IC301 * : Refer to CIRCUIT BOARD (BASE UNIT) ()
http://schema99.host.sk/
NOTE (HANDSET) : RF IC is IC801 CPU is IC601 * : Refer to CIRCUIT BOARD (HANDSET) ()
NOTE (BASE UNIT) : RF IC is IC401
http://schema99.host.sk/
7.9 Check Handset Transmission
TOP PREVIOUS NEXT
Cross Reference: Signal Route ().
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.10 Check Handset Reception
TOP PREVIOUS NEXT
Cross Reference: HOW TO CHECK THE HANDSET SPEAKER (). Signal Route ()
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.11 Check Call ID
TOP PREVIOUS NEXT
Cross Reference: Telephone Line Interface (). Calling Line Identification Circuit (Caller ID) (). NOTE:
l
Make sure the format of the Caller ID service of the Telephone company that the customer subscribed to.
l
Also we recommend to confirm that the customer is really a subscriber of the service.
TOP PREVIOUS NEXT
http://schema99.host.sk/
7.12 Bell Reception
TOP PREVIOUS NEXT
Cross Reference: Telephone Line Interface (). Check Link () NOTE: DSP is IC301.
Cross Reference: Check Link ()
TOP PREVIOUS NEXT
http://schema99.host.sk/
8 ADJUSTMENTS (BASE UNIT)
TOP PREVIOUS NEXT If your unit have below symptoms, adjust or confirm each item using remedy column from the table.
Symptom The base unit dose not respond to a call from handset. The base unit dose not transmit or the transmit frequency is off. The transmit frequency is off. Remedy * Make adjustments in item ( A ) Make adjustments in item ( B ) Make confirmation in item ( C )
The transmit power output is low, and the operating distance between base unit and handset is less than normal. Make confirmation in item ( D ) The reception sensitivity of base unit is low with noise. The transmit level is high or low. The reception level is high or low. The unit does not link. Make confirmation in item ( E ) Make confirmation in item ( F ) Make adjustments in item ( G ) Make confirmation in item ( H )
* : Refer to Adjustment () 8.1 Test Mode Flow Chart (Base Unit) 8.2 How to Change the Channel 8.3 Adjustment 8.4 Adjustment Standard (Base Unit)
TOP PREVIOUS NEXT
http://schema99.host.sk/
8.1 Test Mode Flow Chart (Base Unit)
TOP PREVIOUS NEXT The operation-flow of Test mode and main check items are shown below.
Note : * Refer to the above table. ** Signal Route () Cross Reference: Check Link ()
TOP PREVIOUS NEXT
http://schema99.host.sk/
8.2 How to Change the Channel
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
8.3 Adjustment
TOP PREVIOUS NEXT
Adjustment Items ( A ) RX VCO Adjustment Test Mode CH10 Talk Adjustment Point T401 Procedure* Check or Replace Parts IC401, T401, C439
l Adjust T401 so that the reading of the Digital
Voltmeter is 1.7V ± 0.1V.
( B ) TX VCO Adjustment
CH10 Talk
T501
l Adjust T501 so that the reading of the Digital
IC501, VD501, T501
Voltmeter is 1.7V ± 0.1V.
( C ) TX Frquency Confirmation
CH10 Talk
-
l Confirm so that the reading of the frequency
counter is 30.300MHz ± 0.7kHz.
IC501, X401, T501, VD501, C430, C431
( D ) TX Power Adjustment
CH10 Talk
T502
l Adjust T502 so that the reading of the RF VTVM is
more than 8dBm.
IC501, Q502, DUP501, T502
( E ) RX Sensitivity Confirmation (2nd IF output)
CH10 Talk
-
1. 2.
Apply 60dBuVemf output from S.S.G. (modulation frequency 1kHz, dev. 0kHz). Confirm that the reading of RF VTVM is the maximum value (more than 20mV)
DUP401, CF401, CF402
(F)
Line Output Level Confirmation
CH10 Talk
-
1. 2.
Apply 60dBuVemf output from S.S.G. (modulation frequency 1kHz, dev. 3kHz). Confirm that the reading of AF VTVM is -1.0dBm ± 2dBm (600 load).
IC401, Q110, VOL401
( G ) Line Input Modulation Adjustment
CH10 Talk
VOL402
1. 2. 3.
Input via loop simulator 1.0kHz, -20dBm (measured at T-R) signal. Apply 60dBuVemf output from S.S.G. (modulation frequency 1kHz, dev. 0kHz). Adjust VOL402 so that the reading of FM Deviation Meter is 3.0kHz ± 0.5 kHz.
IC401, VD501, VOL402
( H ) Noise Squelch Confirmation
CH10 Talk
-
1. 2.
Measure the SSG output level when the noise squelch changes from Low to High. Confirm that the SSG output level is -5 ~ +10dBuVemf.
IC401, DUP401
* : The connection of adjustment equipment are as shown in Adjustment Standard (Base Unit) (). SSG Frequency : 40.00 MHz.
TOP PREVIOUS NEXT
http://schema99.host.sk/
8.4 Adjustment Standard (Base Unit)
TOP PREVIOUS NEXT
Note : ( A ) - ( H ) is refered to ADJUSTMENTS (BASE UNIT) ()
TOP PREVIOUS NEXT
http://schema99.host.sk/
9 ADJUSTMENTS (HANDSET)
TOP PREVIOUS NEXT If your unit have below symptoms, adjust or confirm each item using remedy column from the table.
Symptom The movement of Battery Low Indicator is wrong. The base unit does not respond to a call from handset. The base unit does not transmit or the transmit frequency is off. The transmit frequency is off. Remedy * Make confirmation in item ( A ) Make adjustment in item ( B ) Make adjustment in item ( C ) Make confirmation in item ( D )
The transmit power output is low, and the operating distance between base unit and Handset is less than normal. Make confirmation in item ( E ) The reception sensitivity of base unit is low with noise. Does not link between base unit and handset. The reception level is high or low. The transmit level is high or low. Make confirmation item ( F ) Make confirmation in item ( G ) Make confirmation item ( H ) Make adjustment in item ( I )
* : Refer to Adjustment () Unit condition: 1. Remove the antenna lead wire from P.C Board of the handset. 2. Power Supply: DC 3.9V (DC power supply) 3. Volume: HIGH (When P.C. Board of handset is in test mode, volume condition is medium. Press Navigator key , once.) 4. Speaker Load: 150
CH TX Frequency RX Frequency 44.20MHz
CH10 49.970MHz
9.1 Test Mode Flow Chart (Handset) 9.2 How to change the channel 9.3 Adjustment 9.4 Adjustment Standard (Handset)
TOP PREVIOUS NEXT
http://schema99.host.sk/
9.1 Test Mode Flow Chart (Handset)
TOP PREVIOUS NEXT
Note : * Refer to CIRCUIT BOARD (HANDSET) () ** Signal Route () RAM data of CPU is returned to factory default when entering the test mode.
TOP PREVIOUS NEXT
http://schema99.host.sk/
9.2 How to change the channel
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
9.3 Adjustment
TOP PREVIOUS NEXT
Adjustment Items Test Mode Adjustment Point 1. 2. Procedure* Set the power supply voltage to DC3.60V, and confirm so that the reading of oscilloscope is High. Set the power supply voltage to DC 3.40V, and confirm so that the reading of oscilloscope is Low. Check or Replace Parts IC801
( A ) Battery Low Confirmation CH10 Talk
( B ) TX VCO Voltage Adjustment
CH10 Talk
T901
l Adjust T901 so that the reading of the Digital Voltmeter is
1.2V ± 0.1V.
IC801, X801, T901, VD901
( C ) RX VCO Voltage Adjustment
CH10 Talk
T801
l Adjust T801 so that the reading of the Digital Voltmeter is
IC801, X801, T801
1.2V ± 0.1V.
( D ) TX Frequency Confirmation
CH10 Talk
-
l Confirm so that the reading of the frequency counter is
40.000MHz ± 0.7kHz.
IC801, X801, T901, VD901, C828, C829
( E ) TX Power Adjustment
CH10 Talk
-
l Output level should be over 5dBmV on RF VTVM (50
IC901, DUP901
load).
(F)
RX Sensitivity Confirmation (2nd IF output)
CH10 Talk
-
1. 2.
Apply 60dBuVemf output from S.S.G. (modulation frequency 1kHz, dev. 0kHz). Confirm 2nd IF output so that the reading of RF VTVM is more than 15mV.
DUP801, IC801, CF801, CF802
( G ) Noise Squelch Confirmation
CH10 Talk
-
1.
2.
Measure the SSG output level when the noise squelch changes from Low to High. (modulation frequency 1kHz, dev. 3kHz) Confirm that the SSG output level is -3 ~ +15dBVemf.
IC801, DUP801
( H ) Speaker Output Level confirmation
CH10 Talk
-
1. 2.
Apply 60dBuVemf output from S.S.G. (modulation frequency 1kHz, dev. 3kHz). Confirm that SP output level is -20 ± 5dBm. (distortion: less than 7%) (volume High).
IC801, VOL801
(I)
Mic Modulation Factor Adjustment
CH10 Talk
VOL802
1. 2.
Apply a MIC signal (1kHz, -40 dBm at 600 load). Adjust VR901 so that the reading FM Deviation Meter is 3.2kHz ± 0.7kHz.
IC801, VD901, VOL802
(J)
Data Modulation Confirmation
CH10 Talk
-
1. 2.
Keep pressing the "1" key. Confirm for 2.5kHz ~ 6.5kHz FM Deviation Meter reading.
* : The connections of adjustment equipment are as shown in Adjustment Standard (Handset) (). SSG Frequency: 30.300 MHz
http://schema99.host.sk/
9.4 Adjustment Standard (Handset)
TOP PREVIOUS NEXT
Note : ( A ) - ( J ) is refered to Adjustment ()
TOP PREVIOUS NEXT
http://schema99.host.sk/
11 HOW TO CHECK THE HANDSET SPEAKER
TOP PREVIOUS NEXT 1. Prepare the digital voltmeter, and set the selector knob to ohm meter. 2. Put the probes at the speaker terminals as shown below.
TOP PREVIOUS NEXT
http://schema99.host.sk/
12 FREQUENCY TABLE (MHz)
TOP PREVIOUS NEXT
BASE UNIT HANDSET
Channel Transmit Frequency Receive Frequency Transmit Frequency Receive Frequency 1 2 3 4 5 6 7 8 9 10 30.0750 30.1250 30.1750 30.2250 30.2750 30.1000 30.1500 30.2000 30.2500 30.3000 39.7750 39.8250 39.8750 39.9250 39.9750 39.8000 39.8500 39.9000 39.9500 40.0000 39.7750 39.8250 39.8750 39.9250 39.9750 39.8000 39.8500 39.9000 39.9500 40.0000 30.0750 30.1250 30.1750 30.2250 30.2750 30.1000 30.1500 30.2000 30.2500 30.3000
TOP PREVIOUS NEXT
http://schema99.host.sk/
13 EXPLANATION OF CPU DATA COMMUNICATION
TOP PREVIOUS NEXT 13.1 STAND-BY -> TALK, TALK -> STAND-BY 13.2 Ringing 13.3 Changing the channel 13.4 Ports for transmitting and receiving of data 13.5 Waveform of DATA used for cordless transmission and reception 13.5.1 Handset 13.5.2 Base Unit
TOP PREVIOUS NEXT
http://schema99.host.sk/
13.1 STAND-BY -> TALK, TALK -> STANDBY
TOP PREVIOUS NEXT
Note : * The channel is changed if the noise interferes with the conversation.
TOP PREVIOUS NEXT
http://schema99.host.sk/
13.2 Ringing
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
13.3 Changing the channel
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
13.4 Ports for transmitting and receiving of data
TOP PREVIOUS NEXT Handset: transmitting (TX)... 33 Pin receiving (RX)... 27 Pin Base Unit: transmitting (TX)... 97 Pin receiving (RX)... 59 Pin
TOP PREVIOUS NEXT
http://schema99.host.sk/
13.5 Waveform of DATA used for cordless transmission and reception
TOP PREVIOUS NEXT The DATA which is transmitted from the Handset to the Base Unit is combination of DATA 0, DATA 1, DATA Delimit. The DATA which is transmitted from the Base Unit to the Handset is combination of DATA 0, DATA 1, DATA Delimit. 13.5.1 Handset 13.5.2 Base Unit
TOP PREVIOUS NEXT
http://schema99.host.sk/
13.5.1 Handset
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
Stránka c. 1 z 1
13.5.2 Base Unit
TOP PREVIOUS NEXT
l
For example (one of part of data)
TOP PREVIOUS NEXT
http://schema99.host.sk/
14 BLOCK DIAGRAM (BASE UNIT)
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
16 BLOCK DIAGRAM (HANDSET)
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
18 CPU (DSP) DATA (BASE UNIT)
TOP PREVIOUS NEXT 18.1 IC301
TOP PREVIOUS NEXT
http://schema99.host.sk/
18.1 IC301
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
19 CPU (DSP) DATA (HANDSET)
TOP PREVIOUS NEXT 19.1 IC601
TOP PREVIOUS NEXT
http://schema99.host.sk/
19.1 IC601
TOP PREVIOUS NEXT
TOP PREVIOUS NEXT
http://schema99.host.sk/
27 FOR SCHEMATIC DIAGRAM
TOP PREVIOUS NEXT 27.1 Base Unit (SCHEMATIC DIAGRAM (BASE UNIT)) 27.2 Handset (SCHEMATIC DIAGRAM (HANDSET))
TOP PREVIOUS NEXT
http://schema99.host.sk/
27.1 Base Unit ( SCHEMATIC DIAGRAM (BASE UNIT) )
TOP PREVIOUS NEXT 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
Important Safety Notice: Components identified by mark have special characteristics important for safety. When replacing any of these components, use only the manufacturer´sspecified parts.
TOP PREVIOUS NEXT
http://schema99.host.sk/
27.2 Handset ( SCHEMATIC DIAGRAM (HANDSET) )
TOP PREVIOUS NEXT 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
TOP PREVIOUS NEXT
http://schema99.host.sk/
28 VOLTAGE CHECK
TOP PREVIOUS NEXT 28.1 Base unit 28.2 Handset 28.3 MEMO
TOP PREVIOUS NEXT
http://schema99.host.sk/
28.1 Base unit
TOP PREVIOUS NEXT
STBY TALK IC301-1 IC301-2 IC301-3 IC301-4 IC301-5 IC301-6 IC301-7 IC301-8 IC301-9 IC301-10 IC301-11 IC301-12 IC301-13 IC301-14 IC301-15 IC301-16 IC301-17 IC301-18 IC301-19 IC301-20 IC301-21 IC301-22 IC301-23 IC301-24 IC301-25 IC301-26 IC301-27 IC301-28 IC301-29 IC301-30 IC301-31 IC301-32 IC301-33 IC301-34 IC301-35 IC301-36 IC301-37 IC301-38 IC301-39 IC301-40 IC301-41 IC301-42 IC301-43 IC301-44 IC301-45 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 4.7 0 4.7 4.7 0 0 0 4.7 0.5 0 4.7 0 4.7 4.7 0 0 0 4.7 4.7 0 2.3 2.3 4.9 2.3 2.3 4.8 2.3 2.3 0 2.3 2.1 2.3 2.3 2.3 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 4.7 0 0 0 0 0 0 4.7 0.8 0 4.7 0 0 0 0 4.5 0 0 0 0 2.3 2.3 4.9 2.3 2.3 4.8 2.3 2.3 2.7 2.3 2.1 2.3 2.3 2.3 SP 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 4.7 0 0 0 0 0 0 4.7 0.8 0 4.7 0 0 0 0 4.5 0 0 0 0 2.2 2.2 4.9 2.3 2.3 4.8 2.3 2.3 2.7 2.3 2.1 2.3 2.3 2.3 CHG 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 4.7 0 4.7 4.7 0 0 0 0 0.5 0 4.7 0 4.7 4.7 0 0 0 4.7 4.7 0 2.3 2.3 4.9 2.3 2.3 4.8 2.3 2.3 0 2.3 2.1 2.3 2.3 2.3
http://schema99.host.sk/
IC301-46 IC301-47 IC301-48 IC301-49 IC301-50 IC301-51 IC301-52 IC301-53 IC301-54 IC301-55 IC301-56 IC301-57 IC301-58 IC301-59 IC301-60 IC301-61 IC301-62 IC301-63 IC301-64 IC301-65 IC301-66 IC301-67 IC301-68 IC301-69 IC301-70 IC301-71 IC301-72 IC301-73 IC301-74 IC301-75 IC301-76 IC301-77 IC301-78 IC301-79 IC301-80 IC301-81 IC301-82 IC301-83 IC301-84 IC301-85 IC301-86 IC301-87 IC301-88 IC301-89 IC301-90 IC301-91 IC301-92 IC301-93 IC301-94 IC301-95
0 2.3 2.3 2.3 0 4.9 4.9 0.4 0.7 0 4.9 1.8 4.7 2.1 4.7 0 0 4.7 4.7 4.7 4.7 4.7 1.3 1.3 1.3 1.3 1.3 1.3 0 4.7 0 0 0 0 0 0 4.6 4.7 0 0 0 0 0 0 0 0 0 4.7 4.7 4.7
0 2.3 2.3 2.2 0 4.9 4.9 0.4 0.7 0 4.9 1.8 4.7 0.9 4.7 0 0 4.7 4.7 0.1 4.7 4.7 1.3 1.3 1.3 1.3 1.3 1.3 0 4.7 0 0 0 0 0 0 4.6 4.7 0 0 0 0 0 0 0 0 0 4.7 4.7 4.7
0 2.3 2.3 2.3 0 4.9 4.9 0.4 0.7 0 4.9 1.8 4.7 0.9 4.7 0 0 4.7 4.7 0.1 0.2 4.7 1.3 1.3 1.3 1.3 1.3 1.3 0 4.7 0 0 0 0 0 0 4.6 4.7 0 0 0 0 0 0 0 0 0 4.7 4.7 4.7
0 2.3 2.3 2.3 0 4.9 4.9 0.4 0.7 0 4.9 1.8 4.7 2.1 4.7 0 0 4.7 4.7 0.1 4.7 4.7 1.3 1.3 1.3 1.3 1.3 1.3 0 4.7 0 0 0 0 0 0 4.6 4.7 0 0 0 0 0 0 0 0 0 4.7 4.7 4.7
http://schema99.host.sk/
IC301-96 IC301-97 IC301-98 IC301-99 IC301-100 IC302-1 IC302-2 IC302-3 IC302-4 IC303-1 IC303-2 IC303-3 IC303-4 IC303-5 IC303-6 IC303-7 IC303-8 IC304-1 IC304-2 IC304-3 IC304-4 IC304-5 IC304-6 IC304-7 IC304-8 IC304-9 IC304-10 IC304-11 IC304-12 IC304-13 IC304-14 IC304-15 IC304-16 IC304-17 IC304-18 IC304-19 IC304-20 IC304-21 IC304-22 IC304-23 IC304-24 IC304-25 IC304-26 IC304-27 IC304-28 IC304-29 IC304-30 IC304-31 IC304-32 IC304-33
4.7 0 0 0 2.4 0 4.9 4.2 4.9 0 0 0 4.7 4.7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4.7 0 0 0 0 0 0 0 0 0 -
4.7 0 0 4.7 2.4 0 4.9 4.2 4.9 0 0 0 4.7 4.7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4.7 0 0 0 0 0 0 0 0 0 -
4.7 0 0 4.7 2.4 0 4.9 4.2 4.9 0 0 0 4.7 4.7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4.7 0 0 0 0 0 0 0 0 0 -
4.7 0 0 0 2.4 0 4.9 4.2 4.9 0 0 0 4.7 4.7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4.7 0 0 0 0 0 0 0 0 0 -
http://schema99.host.sk/
IC304-34 IC304-35 IC304-36 IC304-37 IC304-38 IC304-39 IC304-40 IC304-41 IC304-42 IC304-43 IC304-44 IC401-1 IC401-2 IC401-3 IC401-4 IC401-5 IC401-6 IC401-7 IC401-8 IC401-9 IC401-10 IC401-11 IC401-12 IC401-13 IC401-14 IC401-15 IC401-16 IC401-17 IC401-18 IC401-19 IC401-20 IC401-21 IC401-22 IC401-23 IC401-24 IC401-25 IC401-26 IC401-27 IC401-28 IC401-29 IC401-30 IC401-31 IC401-32 IC401-33 IC401-34 IC401-35 IC401-36 IC401-37 IC401-38 IC401-39
0 0 0 0 0 0 0.4 4.7 4.7 4.7 0 0.6 2.9 2.9 2.9 2.9 8.1 2.9 2.9 2 0 8.1 2 0 0.3 3.4 3.4 0 0 0 3 3.6 0 3 3 3 2.9 2.9 4.6 0 2.7 4.6 4.6 5.3 3.9 8.1 1 0 3.8
0 0 0 0 0 0 0.4 4.7 4.7 4.7 0 0.6 2.9 2.9 2.9 2.9 8.1 2.9 2.9 0.1 0 8.1 1 0 0.3 3.4 3.4 0 0 0 3 3.6 0.5 3 3 3 2.9 2.9 4.6 0 2.7 4.6 4.6 5.3 3.9 8.1 1 0 3.8
0 0 0 0 0 0 0.4 4.7 4.7 4.7 0 0.6 2.9 2.9 2.9 2.9 8.1 2.9 2.9 0.1 0 8.1 1 0 0.3 3.4 3.4 0 0 0 3 3.6 0.5 3 3 3 2.9 2.9 4.6 0 2.7 4.6 4.6 5.3 3.9 8.1 1 0 3.8
0 0 0 0 0 0 0.4 4.7 4.7 4.7 0 0.6 2.9 2.9 2.9 2.9 8.1 2.9 2.9 2 0 8.1 2 0 0.3 3.4 3.4 0 0 0 3 3.6 0 3 3 3 2.9 2.9 4.6 0 2.7 4.6 4.6 5.3 3.9 8.1 1 0 3.8
http://schema99.host.sk/
IC401-40 IC401-41 IC401-42 IC401-43 IC401-44 IC401-45 IC401-46 IC401-47 IC401-48 IC401-49 IC401-50 IC401-51 IC401-52 IC401-53 IC401-54 IC401-55 IC401-56 IC501-1 IC501-2 IC501-3 IC501-4 IC501-5 IC501-6
0 1.2 1.2 1.3 0.7 0.7 0 1.3 2.7 2.6 2.6 0 1.4 1.3 4.7 4.7 0 0.6 0 0.6 0.4 0 0.6
0 1.2 1.2 1.2 0.6 0.6 0 1.2 1.2 2.6 1.4 0 1.4 1.3 0.1 4.7 0 4.6 0.8 4.6 3.2 0 4.6
0 1.2 1.2 1.2 0.6 0.6 0 1.2 1.2 2.6 1.4 0 1.4 1.3 0.1 4.7 0 4.6 0.8 4.6 3.2 0 4.6
0 1.2 1.2 1.3 0.7 0.7 0 1.3 2.7 2.6 2.6 0 1.4 1.3 4.7 4.7 0 0.6 0 0.6 0.4 0 0.6
Q101-1 Q101-2 Q101-3 Q102-1 Q102-2 Q102-3 Q103-1 Q103-2 Q103-3 Q104-1 Q104-2 Q104-3 Q105-1 Q105-2 Q105-3 Q106-1 Q106-2 Q106-3 Q107-1 Q107-2 Q107-3 Q108-1 Q108-2 Q108-3 Q109-1 Q109-2
47.3 0 46.7 0 46.7 0 -
11.9 11.3 11.2 0 0 0.7 -
-
-
11.9 47.3 11.3 0
11.2 46.7 0 0 0.7 0 46.7 0 -
http://schema99.host.sk/
Q109-3 Q110-1 Q110-2 Q110-3 Q111-1 Q111-2 Q111-3 Q112-1 Q112-2 Q112-3 Q113-1 Q113-2 Q113-3 Q114-1 Q114-2 Q114-3 Q201-1 Q201-2 Q201-3 Q202-1 Q202-2 Q202-3 Q203-1 Q203-2 Q203-3 Q204-1 Q204-2 Q204-3 Q301-1 Q301-2 Q301-3 Q302-1 Q302-2 Q302-3 Q303-1 Q303-2 Q303-3 Q501-1 Q501-2 Q501-3 Q502-1 Q502-2 Q502-3 Q503-1 Q503-2 Q503-3
0.2 0 0 0 0 4.7 0 0 0 5.5 8.1 6.2 0 0 4.7 0 0.6 0 4.8 0 1.8 0 0 0 4.7 4.9 4.7 5.1 4.7 0.6 0 0.6 8.1 0.6 4.7 0.6
6 11.3 6.6 0 0 4.7 0 0 0 5.5 8.1 6.2 0 0 4.7 0 0.6 0 4.8 0 1.8 0 0.8 0 4.7 4.9 4.7 4.6 0 4.6 0.2 0.8 7.4 4.6 3.3 4.6
6 11.3 6.6 0 0 4.7 0 0 0 5.5 8.1 6.2 0 0 4.7 0 0.6 0 4.8 0 1.8 0 0.8 0 4.7 4.9 4.7 4.6 0 4.6 0.2 0.8 7.4 4.6 3.3 4.6
0.2 0 0 0 0 4.7 0 0 0 5.5 8.1 6.2 0 0.6 0 0 0.6 0 4.8 0 1.8 0 0 0 4.7 4.9 4.7 5.1 4.7 0.6 0 0.6 8.1 0.6 4.7 0.6
DUP401-1 DUP401-2 DUP401-3
0 0 7.7
-0.4 0 7.7
-0.4 0 7.7
0 0 7.7
http://schema99.host.sk/
DUP401-4 DUP401-5 DUP401-6 DUP501-1 DUP501-2 DUP501-3 DUP501-4 DUP501-5 DUP501-6
0 0 0 0 0 8.1 8.1
0 0 0 -0.4 0 7.4 7.9
0 0 0 -0.4 0 7.4 7.9
0 0 0 0 0 8.1 8.1
D103- + D104- D105- 3 D106- 4 D203-A D203-K D204-A D204-K D205-A D205-K
47.3 0 0 47.7 5.5 4.7 5.5 4.8 5.5 4.9
11.9 0 -0.7 12.7 5.5 4.7 5.5 4.8 5.5 4.8
11.9 47.3 0 -0.7 0 0
12.7 47.7 5.5 4.7 5.5 4.8 5.5 4.8 5.5 4.7 5.5 4.8 5.5 4.9
REG201-1 REG201-2 REG201-3
11.7 8.1 0
11.4 8.1 0
11.4 11.7 8.1 0 8.1 0
DC12V RING TIP CH3 CH4
11.7 47.7 0 8.1 0
11.5 12.7 -0.8 8.1 0
11.5 11.7 12.7 47.7 -0.8 8.1 0 0 8 1.9
TOP PREVIOUS NEXT
http://schema99.host.sk/
28.2 Handset
TOP PREVIOUS NEXT
STBY TALK CHG IC601-1 IC601-2 IC601-3 IC601-4 IC601-5 IC601-6 IC601-7 IC601-8 IC601-9 IC601-10 IC601-11 IC601-12 IC601-13 IC601-14 IC601-15 IC601-16 IC601-17 IC601-18 IC601-19 IC601-20 IC601-21 IC601-22 IC601-23 IC601-24 IC601-25 IC601-26 IC601-27 IC601-28 IC601-29 IC601-30 IC601-31 IC601-32 IC601-33 IC601-34 IC601-35 IC601-36 IC601-37 IC601-38 IC601-39 IC601-40 IC601-41 IC601-42 IC601-43 IC601-44 IC601-45 3.6 3.6 0 0 3.6 3.6 3.6 1.7 1.7 0 1.4 1.7 0 0 3.6 0 0.1 0 0.1 3.6 3.6 0 0 0 0 0 2.6 3.6 0.6 3.6 0 0 0 3 3.6 3.6 0 0 0 0 3.6 0 3.6 0 0 3.6 3.6 0 0 3.6 3.6 3.6 1.7 1.7 0 1.4 1.7 0 0 3.6 0 0 0 0 3.6 3.6 0 0 0 0 0.2 1.8 3.6 3.6 3.6 0 0 0 2.9 3.6 0.2 0 0 0 0 3.6 0 3.6 0 0 3.6 3.6 0 0 3.6 3.7 3.6 1.7 1.7 0 1.4 1.7 0 0 3.6 0 0.1 0 0.1 3.6 3.6 0 0 0 0 0 2.6 3.6 0.6 3.6 0 0 0 3 3.6 3.6 0 0 0 0 3.6 0 3.6 0 0
http://schema99.host.sk/
IC601-46 IC601-47 IC601-48 IC601-49 IC601-50 IC601-51 IC601-52 IC601-53 IC601-54 IC601-55 IC601-56 IC601-57 IC601-58 IC601-59 IC601-60 IC601-61 IC601-62 IC601-63 IC601-64 IC801-1 IC801-2 IC801-3 IC801-4 IC801-5 IC801-6 IC801-7 IC801-8 IC801-9 IC801-10 IC801-11 IC801-12 IC801-13 IC801-14 IC801-15 IC801-16 IC801-17 IC801-18 IC801-19 IC801-20 IC801-21 IC801-22 IC801-23 IC801-24 IC801-25 IC801-26 IC801-27 IC801-28 IC801-29 IC801-30 IC801-31
3.6 3.6 3.6 3.6 3.6 3.6 0 0 0 0 0 2.4 2.4 2.4 2.4 0 3.6 3.6 3.6 0 0.1 0 0 0 0 3 0 0 2.1 3.6 3.9 1.9 0 0.1 0.1 0 0 0 0 0 2.6 0 0 0 2.3 2.1 2.1 1.3 0 1.9
3.6 3.6 3.6 3.6 3.6 3.6 0 0 0 0 0 2.4 2.4 2.4 2.4 0 3.6 3.6 3.6 0 0.6 1.8 2 2.1 2.1 2.9 2.1 2 2.1 3.6 3.9 2 0 1.7 1.7 1.7 0.1 0 0 2.1 2.6 0.8 2 2 2.6 1.9 1.9 0.4 0 1.6
3.6 0.04 3.6 3.6 3.6 3.6 0 0 0 0 0 2.4 2.4 2.4 2.4 0 3.6 3.6 3.6 0 0.1 0 0 0 0 3 0 0 2.1 3.6 3.9 1.9 0 0.1 0.1 0 0 0 0 0 2.6 0 0 0 2.3 2.1 2.1 1.3 0 1.9
http://schema99.host.sk/
IC801-32 IC801-33 IC801-34 IC801-35 IC801-36 IC801-37 IC801-38 IC801-39 IC801-40 IC801-41 IC801-42 IC801-43 IC801-44 IC801-45 IC801-46 IC801-47 IC801-48 IC801-49 IC801-50 IC801-51 IC801-52 IC801-53 IC801-54 IC801-55 IC801-56 IC901-1 IC901-2 IC901-3 IC901-4 IC901-5 IC901-6
3.2 3.2 3.2 2.4 3.9 1 0 2.4 0 1.2 1.2 1.1 0.7 0.7 0 1.1 0 2.1 2.1 0 1.1 1 3.6 0.1 0.1 0.1 0 0.1 0.1 0 0.1
3.2 3.2 3.2 2.4 3.9 1 0 2.4 0 1.2 1.2 1.1 0.5 0.5 0 1.1 1.5 2.1 1.1 0 1.1 1 3.6 0 0 3.7 0.8 3.8 2.4 0 3.7
3.2 3.2 3.2 2.4 3.9 1 0 2.4 0 1.2 1.2 1.1 0.7 0.7 0 1.1 0 2.1 2.1 0 1.1 1 3.6 0.1 0.1 0.1 0 0.1 0.1 0 0.1
Q601-1 Q601-2 Q601-3 Q602-1 Q602-2 Q602-3 Q701-1 Q701-2 Q701-3 Q702-1 Q702-2 Q702-3 Q703-1 Q703-2 Q703-3 Q704-1 Q704-2 Q704-3
0 0 2.5 3.9 3.6 0 0 0 0 0 0 3.6 0 0 3.6 3.9 3.6 0
0 0 2.5 3.9 3.6 0 0 0 0 0 0 3.6 0 0 3.6 3.9 3.6 0
0 0 2.5 3.9 3.3 3.9 0.4 -0.2 -0.3 0 4.2 0 0 0 3.6 3.9 3.6 0
http://schema99.host.sk/
Q705-1 Q705-2 Q705-3 Q706-1 Q706-2 Q706-3 Q901-1 Q901-2 Q901-3 Q902-1 Q902-2 Q902-3
0 3.6 0 3.6 0 3.6 3.9 3.6 0.1 0.1 0 0.1
0 3.6 0 3.6 0 3.6 3.9 0.2 3.8 3.8 0.2 3.8
0 3.6 0 3.6 0 3.6 3.9 3.6 0.1 0.1 0 0.1
DUP801-1 DUP801-2 DUP801-3 DUP801-4 DUP801-5 DUP801-6 DUP901-1 DUP901-2 DUP901-3 DUP901-4 DUP901-5 DUP901-6
0 0 2.9 0 0 0 0 0 0.1 0 0.1 0.1
0 0 2.9 0 0 0 0 0 0.1 0 0.1 0.1
0 0 2.9 0 0 0 0 0 0.1 0 0.1 0.1
BAT1 BAT2 CHG3 CHG4
-
-
3.9 0 -1.1 4.8
TOP PREVIOUS NEXT
http://schema99.host.sk/