Text preview for : Samsung chasis KCT57A service manual.pdf part of Samsung All Service manual Samsung chasis KCT57a all models
Back to : Samsung chasis KCT57A ser | Home
COLOR TELEVISION RECEIVER
Chassis : Model: K51A TXJ2060 TXJ2066 TXJ2067 TXJ2554 TXJ2566 TXJ2567 TXJ2754 TXJ2766 TXJ2767 TXJ2768 TXJ2879
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions
2. Specifications and IC Data
3. Alignment and Adjustments
4. Troubleshooting
5. Exploded Views and Parts List
6. Electric Parts List
7. Block Diagrams
8. Schematic Diagrams
ELECTRONICS
© Samsung Electronics Co., Ltd. APR.1999
Printed in Korea 3K51A-2001
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which peopleÑparticularly childrenÑmight insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unitÕs AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called Òhorizontal disableÓ or Òhold-downÓ.) Heed the high voltage limits. These include the XÐray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturerÕs warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs Òintegral implosionÓ protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some Òin-lineÓ picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such Òpermanently attachedÓ yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the originalÑeven if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ! ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning 1 : First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unitÕs AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor (Òsolid stateÓ) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying powerÑ this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as Òanti-staticÓ; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Samsung Electronics
Specifications and IC Data
2. Specifications and IC Data
2-1 Specifications
MODEL VOLTAGE POWER CONSUMPTION POWER FREQUENCY CHANNELS RECEIVED
CT-5072BWZ CT-5072BPZ
CT-565BZ / 566BWZ CT-567BWZ / 568BPZ CT-225BZ / 228BWZ CT-22B6PZ
CT-25D4WZ
CT-29D4WZ
CT-765DWZ CT-766DWZ CT-30D6PZ CT-30A9PZ 120 WATTS
AC100-240V (Mexico: AC127V±10%) 85 WATTS 110 WATTS 120 WATTS 50/60Hz (Mexico: 60Hz)
VHF; 2~13, UHF; 14~69, CATV; 1,14~125
MODEL
TXJ2048/2060 TXJ2066/2067
TXJ2554/2566 TXJ2567
TXJ2754/2766 TXJ2767/2768
TXJ2879
VOLTAGE POWER CONSUMPTION POWER FREQUENCY CHANNELS RECEIVED 85 WATTS
AC120V 110 WATTS 60Hz VHF; 2~13, UHF; 14~69, CATV; 1,14~125 120 WATTS 130 WATTS
MODEL VOLTAGE POWER CONSUMPTION POWER FREQUENCY CHANNELS RECEIVED
CN-565BWZ CN-566BWZ
CN-25D4WZ CN-663AWZ
CN-29D4WZ CN-7202WZ CN-765DWZ 120 WATTS
AC 100-240V (Argentina: AC 220V) 85 WATTS 110 WATTS 50/60 Hz (Argentina: 50 Hz) VHF: 2~13, UHF: 14~69, CATV: 1,14~125
Samsung Electronics
2-1
Specifications and IC Data
2-2 IC Line Up
Table 2 - 1 IC Line - Up Loc No SF101 SF102 No 1 2 Specification M3951M M9260M TDA8377 IC201 3 TDA8373 TDA8375 IC202 IC301 4 5 LA7510 LA7845 TDA7056B IC603 6
TDA7266S
Description SAW FILTER (VIF) SAW FILTER (SIF) ONECHIP TV PROCESSOR ONECHIP TV PROCESSOR ONECHIP TV PROCESSOR AUDIO IF AMP/4.5M DETECT VERTICAL AMP IC
1.5W x 2 (MONO)
Remarks
CT566BV/CT567BW/CT568BW/CT766DW CT633BW/CT683BW CN565BW/CN25D4W/CN663A/CN765DW
SOUND AMP IC
3W x 2 (MONO)
STEREO MODEL IC701 7 TDA7449 VOLUME CONTROL IC CT633BW/CT683BW/CT766DW IC801 8 KA3S1265R POWER IC CT566BV/CT566BW/CT567BW/CT568BW IC802 IC901 IC902 ICD01 9 10 11 12 KA7630 SZM368ET XL24C08P CXA2104S MULTI REGULATOR IC MICOM EEPROM MTS IC STEREO MODEL ONLY
2-2
Samsung Electronics
Specifications and IC Data
2-3 Semiconductor Base Diagrams
ELECTROLYTICCONDENSER DIODE
IC XLS24C08P (PIN 8) TDA8377 (PIN 56)
TRANSISTOR
TRANSISTOR
SAW-FILTER
KSC2073 KSA940 2SD1887 2SD1880 KSD5072 KSD5703
M3951M M9260M KSC815Y KSA539-Y
1
B
C
E
E B C
IC
TRANSISTOR
TRANSISTOR
LA7845 KA7812 KA7809
C2331-Y KSR1010
IN
G
out
E C B
Fig. 2-1 Semiconductor Base Diagrams
Samsung Electronics
2-3
Specifications and IC Data
2-4 One Chip TV-processor
SOUND IF INPUT EXT AUDIO INPUT VCO REF FILTER VCO REF FILTER PLL LOOP FILTER IF VIDEO OUTPUT BUSINPUT : SCL BUSINPUT : SDA BANDGAP DECOUPLING CHROMA INPUT Y/CVBS INPUT MAIN POSITIVE SUPPLY INT CVBS INPUT GROUND AUDIO OUT DECOUPLING FILTER TUNING EXT CVBS INPUT BLACK CURRENT INP BLUE OUTPUT GREEN OUTPUT RED OUTPUT V-GUARD INP/BEAM CUR LIMITER RED INPUT GREEN INPUT BLUE INPUT PIP/OSD RGB INSERTION SWITCH INP LUMINANCE INPUT LUMINANCE OUTPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30
DECOUPLING SOUND DEMODULATOR AUDIO DEEMPHASSIS/MPX OUT TUNER AGC OUTPUT AGC DECOUPLING CAPACITOR REREFERENCE CURRENT INPUT VERT, SAWTOOTH CAPACITOR EHT/OVERVOLTAGE PROTECTION INP (X-RAY PROTECTION) IF INPUT IF INPUT VERT. DRIVE NEG VERT. DRIVE POS EAST-WEST DRIVE GROUND PHI1 FILTER PHI2 FILTER / FLASH PROT SAND CASTLE OUTPUT/FLYBACK INP HOR. OUTPUT BLACK PEAK HOLD CAPACITOR CVBS OUTPUT POSITIVE SUPPLY LOOP FILTER BURST PHASE DET X-TAL (PAL-N (4.43)/PAL-M (3.58)) X-TAL (3.58) SECAM REF OUTPUT (R-Y) INPUT (B-Y) INPUT (R-Y) OUTPUT (B-Y) OUTPUT
SDIL56
Fig. 2-2 SDIL56
29
CVBS : Composite Video Blanking Signal
2-4
Samsung Electronics
Alignment and Adjustments
3. Alignment and Adjustments
3-1 Preadjustment
1. Since there are no VRs in the K51A chassis, all adjustments after parts replacement must be done in the Service Mode. 2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced. 3. Do not tamper with the Ò AdjustmentÓ screen of the Factory Mode menu. This screen is intended only for factory use. 4. WHEN EEPROM (IC902) IS REPLACED (1) When IC902 is replaced, all adjustment data revert to their initial values. It is necessary to re-program this data. (2) After IC902 is replaced, warm up the TV for 10 seconds. Make the following adjustments AFTER setting up purity and convergence: White Balance Sub-Brightness Vertical Center Vertical Size Horizontal Size (No use in 21Ó and 25Ó models)
3-2 Factory ("SERVICE") Mode
1. The set must be in Factory (ÒServiceÓ) Mode. Selection sequence: STAND-BY ® MUTE ® 1 ®8 ® 2 ® POWER ON 2. The Ò FACTORY MODEÓ message will be displayed. The Factory Mode has four components : Adjustment, MPX, PIP, Option Byte and Factory Reset. 3. Access the Adjustment Mode by pressing the ÒVOLUMEÓ keys ( , ) The adjustment parameters are listed in the accompanying table. Select them by pressing the CHANNEL keys (v,w). w 4. After completing the Factory Mode adjustments, turn the power switch OFF. w
Samsung Electronics
3-1
Alignment and Adjustments
3-2-1 Adjustment
1. Selection sequence : STAND-BY ® MUTE ® 1 ® 8 ® 2 ® POWER ON 2. Example : Sub-bright Adjustment
SZM368ET1 (R4027)
*FACTORY*
Adjustment Mpx Pattern Option Reset ¯ Press VOL
SZM368ET2 (R4127)
*SERVICE*
Adjustment MTS PIP Option Reset ¯ Press VOL
w
AGC VCO SBT SCT SCR STT RG GG BG SCO VSL
15 62 7 11 8 8 32 32 32 20 26
VS VA HS EWA EWP EWC EWT MAT PLA
32 27 46 52 31 32 31 off 6
AGC VCO SBT SCT SCR STT RG GG BG SCO PLA
15 62 7 11 8 8 32 32 32 20 5
VSLN VSN VAN HSN EWAN EWPN EWCN EWTN
30 32 32 45 45 33 32 38
w VSLP VSP VAP HSP EWAP EWPP EWCP EWPT
30 32 32 39 46 33 32 38
¯ Press CH w
¯ Press CH w
AGC VCO SBT SCT SCR STT RG GG BG SCO VSL
15 62 7 11 8 8 32 32 32 20 26
VS VA HS EWA EWP EWC EWT MAT PLA
32 27 46 52 31 32 31 off 6
AGC VCO SBT SCT SCR STT RG GG BG SCO PLA w
15 62 7 11 8 8 32 32 32 20 5
VSLN VSN VAN HSN EWAN EWPN EWCN EWTN
30 32 32 45 45 33 32 38
VSLP VSP VAP HSP EWAP EWPP EWCP EWPT
30 32 32 39 46 33 32 38
¯ Press VOL SBT 3 ¯
or
¯ Press VOL SBT 3 ¯
POWER OFF
POWER OFF
3-2
Samsung Electronics
w
w
w
or
Alignment and Adjustments
MEMORY SPECIFICATION
Table 3 - 1 Memory Specification
FUNCTION No 1 2 3 4 A D J U S T M E N T 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 OP MODE (OSD) AGC VCO SBT SCT SCR STT RG GG BG SCO VSL VS VA HS EWA EWP EWC EWT PLA SEP BYTE 0 BYTE 1 M P X ATT SPECTRAL WIDEBAND RANGE 63 127 15 13 13 13 63 63 63 63 63 63 63 63 63 63 63 63 10 31 FF FF 15 63 63 x HIGH - LIGHT WHITE BALANCE ADJUSTMENT y Y±5 LOW - LIGHT x y Y ± 0.2 MEASURING PULS ADJUSTMENT VOLTAGE 28B2 8 63 2 7 0 4 32 32 32 20 28 20 38 44 42 45 32 32 5 OFF 8F 03 13 46 32 275 295 33 275 295 1.4 2.4V 29D4WZ 8 63 2 7 0 4 32 32 32 14 26 32 29 48 33 34 32 32 0 OFF 95 00 13 46 32 275 295 40 275 295 1.4 2.4V 225BZ 8 63 2 7 0 4 20 20 20 14 24 32 36 46 47 4 32 32 6 OFF 82 00 OFF OFF OFF 275 295 45 275 295 1.4 2.4V 228BWX 8 63 2 7 0 4 20 20 20 14 24 32 36 46 47 4 32 32 6 OFF 87 00 13 46 32 268 275 45 277 283 1.4 2.4V 25D4WZ 8 63 2 7 0 4 32 32 32 14 23 32 27 41 32 36 32 32 0 OFF 85 00 13 46 32 268 275 40 277 283 1.4 2.4V 565BZ 8 63 2 7 0 4 20 20 20 14 24 32 36 46 47 4 32 32 6 OFF 82 00 OFF OFF OFF 275 295 45 275 295 1.4 2.4V 566BWZ 8 63 2 7 0 4 20 20 20 14 24 32 36 46 47 4 32 32 6 OFF 87 00 13 46 32 275 295 45 275 295 1.4 2.4V 765DWZ 8 63 2 7 0 7 32 32 32 14 25 26 34 46 51 24 32 32 5 OFF 87 00 13 46 32 275 295 35 275 295 1.4 2.4V
Samsung Electronics
3-3
Alignment and Adjustments
3-2-2 Option Table
NOTE : The Option Adjustment must be done in the Service Mode.
3-2-2 (A) OPTION BYTE 00
Table 3-2 Option Byte 00 FUNCTION BYTE : 00 D7 D6 D5 D4 D3 D2 D1 D0 NAME V-SYNC AUTO ON PIP CATV S-VIDEO TONE CRT MPX 0 NOT USED NOT USED NO PIP FUNCTION AIR/STD/HRC/IRC NOT USED NO TONE CONTROL 4 : 3 CRT NOT USED 1 USED ( NO V-SYNC, POWER OFF) USED PIP FUNCTION AIR/STD/HRC/AFN USED TONE CONTROL 12.8 : 9 CRT USED ARMY : 1 REMARK
3-2-2 (B) OPTION BYTE 01
Table 3-3 Option Byte 01 FUNCTION BYTE : 01 D7 D6 D5 LANGUAGE D4 D3 D2 D1 D0 NO VIDEO MUTE NO AUDIO MUTE ATS V-CHIP AREA USA 00 : ENGLISH 01 : SPANISH (SEDA) 02 : PORTUGUESE 11 : NOT USED VIDEO MUTE AUDIO MUTE NO ATS NO V - CHIP NO VIDEO MUTE NO AUDIO MUTE ATS V-CHIP NT NT PAL M/N SYSTEM/LANGUAGE NAME 0 1 REMARK
PAL
PAL
3-4
Samsung Electronics
Alignment and Adjustments
3-2-4 Factory Reset
When Ò Factory ResetÓ is selected, the User-Control data reverts to the initial values. The User-Control data is available at MENU (picture, sound and the other functions). Note : When Ò Factory ResetÓ is selected, the Factory Mode Data does not change. Selection sequence : Stand-By ® MUTE ® 1 ® 8 ® 2 ® POWER ON
SZM368ET1 (R4027)
¯ * FACTORY *
Adjustment Mpx Pattern Option Reset
SZM368ET2 (R4127)
¯ * SERVICE *
Adjustment MTS PIP Option Reset
¯ Press CH w
Adjustment Mpx Pattern Option Reset
¯ Press CH w
Adjustment MTS PIP Option Reset
¯ Press VOL Execute
¯ Press VOL Execute
3-3 Other Adjustments
3-3-1 General
1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be no objectionable color shading. If color shading is present, perform the purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
Samsung Electronics
w
w
3-5
Alignment and Adjustments
3-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so external degaussing after moving the TV should be unnecessary. However, the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 10 Minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
3-3-4 FOCUS Adjustment
1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
3-3-5 B+ Line Check
There are 3 power modes : 1. ÒAÓ : When AC power supply is connected ; Ò Stand-ByÓ mode. 2. ÒBÓ : When Ò Set Power-ONÓ button is pressed. 3. ÒCÓ : Driven by FBT. Each voltage is marked on its lead-in wire. ( )
3-3-3 High Voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply must be set to either +135V or +125V (for 20Ó screen). Conditions : Full color bar input and normal picture level. 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage must not exceed 29.5KV. 4. Adjust the Brightness and Contrast controls to both extremes. Ensure that the high voltage does not exceed 29.5KV under any conditions. SIZE MAX H-VOLTAGE 27.5KV 29.5KV 29.5KV 29.5KV 21"± 1 25" 29" 29"± 1
3-3-6 F/S (Fail Safe) Circuit Check
1. The failsafe circuit check is the final step after servicing. 2. Turn the power switch on and adjust the screen for ÒNormalÓ. 3. Temporarily short Pin R and Pin X on the chassis (RX05, RX04). Sound and picture will disappear. 4. The TV should remain in this state. This shows that the failsafe circuit is working properly. 5. To restore picture and sound, temporarily turn off the AC power supply. After about 30 seconds, switch power ON.
3-6
Samsung Electronics
Alignment and Adjustments
3-3-7 Color Purity Adjustment
1. Warm up the receiver. Operate it for 20 minutes, with the Brightness control set to maximum. 2. Fully degauss the receiver. Use an external degaussing coil. 3. Roughly adjust convergence by rotating the Convergence Magnet. 4. Input a black and white signal. 6. Loosen the Purity Magnet clamp. Adjust the purity magnet so that the vertical green raster is precisely at the center of the screen. Then tighten the clamp. 7. Slowly move the Deflection Yoke forward, and adjust it for the best overall green screen. 8. Tighten the Deflection Yoke clamp screw.
5. Loosen the Deflection Yoke clamp screw, and move the Deflection Yoke as close to the purity magnet as possible.
DEFLECTION YOKE
CRT
PURITY AND CONVERGENCE MAGNET ASS'Y RUBBER WEDGE 30 30
RUBBER WEDGES
31 mm (1-3/16") GRASS CLOTH TAPE
30 RUBBER WEDGES LOCATION
DEFLECTION YOKE
ADHESIVE RUBBER WEDGES KIT
Fig. 3-1 Tube Assembly
2 POLE PURITY
ADJUST THE ANGLE (VERTICAL LINES) FIXED
YOKE CLAMP SCREW 6 POLE CONVERGENCE 4 POLE CONVERGENCE
ROTATE TWO TABS AT THE SAME TIME (HORIZONTAL LINES)
Fig. 3-2 Purity and Convergence Magnets
Samsung Electronics
3-7
Alignment and Adjustments
3-3-8 Center Convergence Adjustment
Note: Before attempting any convergence adjustment, make sure that the receiver has been powered ON for at least twenty minutes. 1. Input a crosshatch pattern from a color bar generator. 4. Next, turn both tabs at the same time. Keep the angle between the tabs constant, and superimpose the red and blue horizontal lines at the center of the screen. 5. Adjust the two tabs of the 6-pole magnets. Superimpose the red/blue lines on the green. Adjusting the angle affects the horizontal lines. 6. Repeat adjustments 3, 4 and 5. The dot movement is complex because the 4-pole and 6-pole magnets interact.
2. Adjust the Brightness and Contrast controls for a well defined pattern. 3. Adjust the two tabs of the 5-pole magnets. Change the angle between the tabs, and superimpose red and blue vertical lines in the center area of the picture screen.
BLUE
RED
RED/BLUE
GREEN
BLUE RED
RED/BLUE GREEN
4-Pole Magnet Movement
6-Pole Magnet Movement
Fig. 3-3 Center Convergence Adjustment
3-3-9 AGC Adjustment
1. Input a COLOR-BAR pattern. (CH2) 2. Set the RF input signal to 70 dBmV. 3. Use Generator for PM5518 & PM5418. 4. Set AGC (in the Factory Mode) so that the DC level of IC TDA8377 Pin 53 is 3.0±0.05V.
3-3-10 AFT (VCO Adjustment)
1. Input an AGC adjustment signal. 2. Select Factory Mode VCO and press the MUTE key one time. 3. GEOMATRIX adjustments VS VA VSL HS EWA EWP EWC EWT
3-8
Samsung Electronics
Alignment and Adjustments
3-3-11 White Balance Adjustment
3-3-11 (A) SCREEN ADJUSTMENTS
1. Input a TOSHIBA pattern. 2. Check R506 ÒGÓ pin on the CRT PCB with an oscilloscope. 3. Enter the Horizontal Line Mode. 4. Adjust the Screen Control on the FBT so that the waveform of the 21st line is DC 2.0 (±0.5)V. SIZE DC 29" 2.4 26" 2.4 22"
3-3-11 (D) SUB-BRIGHTNESS ADJUSTMENT
1. Input a TOSHIBA pattern. 2. Set SBT so that the brightness level in lowlight is 1.4 F/L.
High-Light
Low-Light
2.4
3-3-11 (B) HIGH-LIGHT ADJUSTMENT 3-3-11 (E) SUB-COLOR ADJUSTMENT
1. NOTE : If a color analyzer is not available, then approximate the following color adjustments Òby eyeÓ. 2. Input a TOSHIBA pattern. 3. Set high-light to 290/300 (X,Y) with a color analyzer. 4. Set low-light to 1.4F/L. 5. Adjust RG, BG and set GG to step 32. 30" HEIGHT LIGHT 33 ± 5 29" 37 ± 5 26" 45 ± 5 22" 45 ± 5 Set ÒSCRÓ in the Service Mode to step 0.
3-3-11 (F) SUB-TINT ADJUSTMENT
Set ÒSTTÓ in the Service Mode to step 4.
3-3-11 (G) VERTICAL SIZE ADJUSTMENT
1. Input a lion head pattern. 2. Set VS to 32 in the Factory Mode. 3. Set VA so that the top margin is 4.0. Adjust SL so that the bottom margin is 4.0. If the top and bottom margins are different, adjust VA so that their sum is 8.0.
3-3-11 (C) SUB-CONTRAST ADJUSTMENT
1. Set SCT so that the brightness level in highlight is 40 F/L (for a 29Ó SCREEN).
3-3-11 (H) HORIZONTAL SHIFT ADJUSTMENT
1. Input a lion head pattern. 2. Adjust ÒHSÓ in the Service Mode so that the left and right margins of the lion head pattern are 5.0 ± 0.5 : CT633BW/CT683BW, 6.3 ± 0.5 : CT566BV/CT566BW/CT568BW/CT765DW/ CT766DW/CT762B/CT25D4/CT29D4.
Samsung Electronics
3-9
Alignment and Adjustments
3-3-12 Power Consumption Reduction Circuit during Stand-by (Option)
3-3-13 Precautions when servicing
1. Q801 can sustain a continuous flow of 11ADC. If Q801 is destroyed, the S-D is shorted. But, the TV functions normally and only the power consumption during stand-by increases (2.5W® 6W). 2. No Picture ON : Q903 is open or DZ809 is shorted. At this time, check both Q903 and DZ809. If the power-consumption reduction circuit does not work normally after checking both Q903 and DZ809, then short the S-D ports of Q801.
130 RECTIFIED DZ809 R812
Q801 SFP9640
OmA FBT B+ OmA TUNER 33V
OmA R801
POWER CONTROL
Q903 R910 10K
For the power system of K51A chassis, all output voltages remain the same during stand-by. So, to reduce power consumption, it is necessary to cut the leakage current flowing through FBT B+ (130V) and tuner port VT (33V) during stand-by (Picture OFF). The power consumption reduction circuit cuts leakage current. A P-channel MOSFET is used as a switching element. The operating principles are as follows: 1. In stand-by, the voltage of the power control port (micom IC) becomes low (0V). During power ON, however, it becomes high (over 4V). 2. The voltage between S-G (Q801 P-channel MOSFET) should be over 3.5V, so that the S-D current (Q801) can keep flowing. 3. When the voltage of the power control port becomes low, the current flowing through Q903 (R812) is cut. 4. When the voltages across R803 become less than 3.5V, the S-D current (Q801) is cut. 5. DZ809 is required for protecting the G-port (Q801).
3-10
Samsung Electronics
Troubleshooting
4. Troubleshooting
4-1 No Raster and No Sound
No Raster and No Sound
No Voltage
Measure the B+ Voltage at the Cathode of D812 (D811) Normal Check +12.5 Line
Abnormal
Check/Replace IC801 Q801
Normal
More than 130V
Check the horiz output signal at TR collector.
Check/Replace AVR Circuit, Horiz Output Circuit and B+ Voltage Line. Open
Normal
Measure the B+ voltage at the cathode of D812*
Check/Replace F801 More than 130V Less than 50V
Normal
Check/Replace FS circuit
Check/Replace AVR circuit (ADJ Pin of STR)
Check/Replace the AVR circuit.
Check/Replace 1) D801 2) Short the Degaussing Coil 3) C801
Check/Replace the power switch
Samsung Electronics
4-1
Troubleshooting
4-2 No Raster (Sound OK)
No Raster (Sound Ok)
Check that CRT Heater is Lighting Yes
No
Check Heater plus
Abnormal
Normal
Abnormal
Check H.V of CRT
Check/Replace FBT
Check/Replace CRT Drive Circuit
Check/Replace FBT Abnormal
Normal
Check/Replace IC201
Check I2C Data
Normal
Check CRT Drive Circuit
4-2
Samsung Electronics
Troubleshooting
4-3 No Vert Scan (Horizontal Line)
Power OFF (after 10 ~ 15 seconds)
In the Factory Mode, select " V-sync Not Used" (See " Option Byte Table 3-2")
Normal
Check D812 (D811)
Abnormal
Normal
Check IC301 Pin 2 , 4 Abnormal Check IC201 Pin 46 , 47 Abnormal Check/Replace IC201
Check T444 Pin 6 , 8 , R410, R409
Check/Replace IC301
Abnormal
Check/Replace FBT
Samsung Electronics
4-3
Troubleshooting
4-4 No Sound
No Sound
Normal
Check IC603 Pin 1 , 2 , 14 , 15
Abnormal
Check Speaker
Abnormal
Check IC603 Pin 12
Normal
Check IC701 Pin 6 , 9
Normal
Check/Replace IC603
Check/Replace IC701 Pin 19 , 20 Abnormal Check ICD01 Pin 1 , 2 Normal Check ICD01 Pin 11 Abnormal Check/Replace IC701
Check ICD01 Pin 3 , 4 , 16
Check/Replace ICD01
4-4
Samsung Electronics
Troubleshooting
4-5 No Color
No Color
Push "Display" Button on the Remocon
OSD " PAL-M" or "PAL-N" or " NTSC" appear? Yes
No
It's not normal signal
Check ICP01
Normal
Check B+ (5V), Replace ICH01
Abnormal Check IC901 8 , 16
Check QL01, QL02 XL01, XL02 and X202 Normal Check/Replace IC201
Abnormal
Check/Replace that part
Samsung Electronics
4-5
MEMO
4-6
Samsung Electronics
Exploded Views & Parts List
5. Exploded Views & Parts List
5-1 TXJ2060, TXJ2066, TXJ2067 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5-2 TXJ2554, TXJ2754 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5-3 TXJ2567, TXJ2566 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5-4 TXJ2766, TXJ2767, TXJ2768 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
5-5 TXJ2879 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Samsung Electronics
5-1
Exploded Views & Parts List
5-1 TXJ2060, TXJ2066, TXJ2067
5-2
Samsung Electronics
Exploded Views & Parts List
No. 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 2 2-1 2-2 2-3 2-4 3 3-1 3-2
Code No. L2001-0183-025
Description CABINET-FRONT CABINET-OPTION CABINET-OPTION
Specification CT-5345HIPSVOBLK
Q'ty 1
Remark LOCAL
AA64-70015A L4083-0263-000 AA61-60003T AA64-40255A AA64-40254A L4083-0263-000 3001-000003 6002-000514 LA97-90003N AA60-10002A AA61-40053A AA03-10030W AA60-10050R L9400-0002 AA27-20003G 3704-000110 L2001-0184-000 6002-000514 AA39-10007Y
BADGE-BRAND KNOB-POWER SPRING-CS INDICATOR-LED WINDOW-REMOCON KNOB-POWER SPEAKER SCREW-TAPPING ASSY-PCB,A/V SCREW-TAPPING STOPPER-PCB CRT-COLOR SCREW-ASSY HOLDER-DEGAUSSING COIL-DEGAUSSING SOCKET-CRT BACK-CABINET SCREW-TAPPING POWER-CORD
-,AL,-,L45,SILVER, ABSHBBLKPRINTGREEN6345/6 -,-,SUS304,0.5,OD7,H -,ACRYL,HB,-,-,5 -,PC,-,-,-,5345 ABSHBBLKPRINTGREEN6345/6 3W,16ohm,88+-2dB,180+-36Hz RH,+,2,M4,L15,ZP -,KCT52A,K51A-,-,S -,RH,+,M4,L12,ZP -,HIPS,HB,-,WHT,AL -,A51KRE83X(D),+380mG,21,90de WC,HH,+M5,L31.5,SWR 20POLYVINIL S/VOLTAGE21 29.1PI,1.0~2.3KVD,I CT-5345/46HIPSVOB RH,+,2,M4,L15,ZP -,EP2/YES,SPT-2 18AWGx2C,2.4m
1 1 1 1 1 1 2 4 1 2 1 1 4 4 1 1 1 5 1 CB+CF V999 PA+CF SPK+CF
Samsung Electronics
5-3
Exploded Views & Parts List
5-2 5- TXJ2554, TXJ2754
5-4
Samsung Electronics
Exploded Views & Parts List
No. 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 2 2-1 2-2 2-3 3 3-1 4
Code No. AA64-31148A AA64-31137A AA64-70010A AA64-70117B AA64-40472A AA64-10733A AA61-60003T AA65-30018A AA64-40473A LA95-90026X AA60-10002A AA64-10732A 6002-000514 6002-000514 3001-001039 3001-000003 L3113-0003-011 AA03-10026A L1000-0027 AA60-10050R AA65-30004A 3704-000114 AA64-31149A AA64-31138A 6002-000516 AA39-10007Y
Description CABINET-FRONT CABINET-FRONT BADGE-BRAND BADGE-BRAND WINDOW-REMOTE KNOB-POWER SPRING-CS CLAMP-WIRE INDICATOR-LED ASSY-PCB,A/V SCREW-TAPPING KNOB-CONTROL SCREW-TAPPING SCREW-TAPPING SPEAKER SPEAKER BOSS-CABINET CRT-COLOR CRT-COLOR25 SCREW-ASSY CLAMP-D,COIL SOCKET CRT CABINET-BACK CABINET-BACK SCREW-TAPPING POWER-CORD
Specification HIPS VO BLK CT6 HIPS VO BLK PA100 CT-633 -,AL,-,L50,SILVER AL,SS,R2000,25,SILVER CT-633 PCVIOLET CT-633 ABS HB BLK CT-633 -,-,SUS304,0.5,OD7, -,NYLON6.6,-,-,DATL PMMA CLR CT-633 CT-683B,KCT57A,NTSC,100 -,RH,+,M4,L12,ZP ABS HB BLK CT-63 RH,+,2,M4,L15,ZP RH,+,2,M4,L15,ZP 160HM,3W 3W,16ohm,88+-2dB,180+-36Hz HIPSVOBLKCT-5073 A68ADT25X01,+380MG,29,111DE A63AFW32X(DARKTIN WC,HH,+M5,L31.5,SWR -,NYLON-66,V0,WHT 14P,29.1,35.5SN,1SH09S/BK HIPS VO BLK CT68 HIPS VO BLK CT-6 RH,+,2,M4,L20,ZP -,EP2/YES,SPT-2 18AWGx2C,2.4m
Q'ty 1 1 1 1 1 1 1 1 1 1 2 1 2 4 2 2 1 1 1 4 8 1 1 1 7 1
Remark TXJ2754 TXJ2554 TXJ2754 TXJ2554
AV+CF KC+CF SPK+CF TXJ2754 TXJ2554
TXJ2754 TXJ2554 CRT+CF V999 TXJ2754 TXJ2554 CB+CF
Samsung Electronics
5-5
Exploded Views & Parts List
5-3 5- TXJ2567, TXJ2566
5-6
Samsung Electronics
Exploded Views & Parts List
No. =1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 2 2-1 2-2 2-3 3 3-1 3-2
Code No. AA64-31346A AA64-70117B AA64-10804A AA61-60003J 6002-000514 3001-001038 AA61-40113A AA60-10002A LA97-90003N AA64-40525A AA64-40524A 6002-000514 AA64-10803A 6002-000514 AA65-30018A L1000-0027 AA60-10050R L9400-0001 3704-000114 AA64-31348A 6002-000514 AA39-10007Y
Description CABINET-FRONT BADGE-BRAND KNOB-POWER SPRING-CS SCREW-TAPPING SPEAKER STOPPER-PCB SCREW-TAPPING ASSY-PCB,A/V INDICATOR-LED WINDOW-REMOTE SCREW-TAPPING KNOB-CONTROL SCREW-TAPPING CLAMP-WIRE CRT-COLOR25 SCREW-ASSY HOLDER-DEGAUSSING SOCKET CRT CABINET-BACK SCREW-TAPPING POWER-CORD
Specification HIPSVOBLKBK708P AL,SS,R2000,25,SILVER CT-633 ABSHBBLK -,-,SUS304,0.5,OD6,H RH,+,2,M4,L15,ZP 6W,16OHM,92DB,140HZ -,ABS,HB,NTR. -,RH,+,M4,L12,ZP -,KCT52A,K51A-,-,S ACRYLCLR PCVIOLET RH,+,2,M4,L15,ZP ABSHBBLK RH,+,2,M4,L15,ZP -,NYLON6.6,-,-,DATL A63AFW32X(DARKTIN WC,HH,+M5,L31.5,SWR 25POLYVINYLCHLORIDEFL 14P,29.1,35.5SN,1SH09S/BK HIPSVOBLK RH,+,2,M4,L15,ZP -,EP2/YES,SPT-2 18AWGx2C,2.4m
Q'ty 1 1 1 1 4 2 1 2 1 1 1 1 1 1 1 1 4 4 1 1 7 1
Remark
SPK+CF
PAV+CF
KC+CF
V999
CB+CF
Samsung Electronics
5-7
Exploded Views & Parts List
5-4 5- TXJ2766, TXJ2767, TXJ2768
5-8
Samsung Electronics
Exploded Views & Parts List
No. 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 2 2-1 2-2 2-3 3 3-1 3-2
Code No. AA64-31345A AA64-70117B AA64-10804A AA61-60003J 6002-000514 3001-000190 AA61-40113A AA60-10002A LA97-90003N AA64-40525A AA64-40524A 6002-000514 AA64-10803A 6002-000514 AA65-30018A AA03-10026R AA60-10050R AA65-30004A 3704-000114 AA64-31347A 6002-000514 AA39-10007Y
Description CABINET-FRONT BADGE-BRAND KNOB-POWER SPRING-CS SCREW-TAPPING SPEAKER STOPPER-PCB SCREW-TAPPING ASSY-PCB,A/V INDICATOR-LED WINDOW-REMOTE SCREW-TAPPING KNOB-CONTROL SCREW-TAPPING CLAMP-WIRE CRT-COLOR SCREW-ASSY CLAMP-D,COIL SOCKET CRT CABINET-BACK SCREW-TAPPING POWER-CORD
Specification HIPSVOBLKBK708P AL,SS,R2000,25,SILVER CT-633 ABSHBBLK -,-,SUS304,0.5,OD6, RH,+,2,M4,L15,ZP 5W,8OHM,89DB,150HZ -,ABS,HB,NTR. -,RH,+,M4,L12,ZP -,KCT52A,K51A-,-,S ACRYLCLR PCVIOLET RH,+,2,M4,L15,ZP ABSHBBLK RH,+,2,M4,L15,ZP -,NYLON6.6,-,-,DATL A70QBZ791X001,+380MG,29,100 WC,HH,+M5,L31.5,SWR -,NYLON-66,V0,WHT 14P,29.1,35.5SN,1SH09S/BK HIPSVOBLK RH,+,2,M4,L15,ZP -,EP2/YES,SPT-2 18AWGx2C,2.4m
Q'ty 1 1 1 1 4 2 1 2 1 1 1 1 1 1 1 1 4 8 1 1 7 1
Remark
SPK+CF
PAV+CF
KC+CF
V999
CB+CF
Samsung Electronics
5-9
Exploded Views & Parts List
5-5 5- TXJ2879
5-10
Samsung Electronics
Exploded Views & Parts List
No. 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 2 2-1 2-2 2-3 3 3-1 3-2
Code No. AA64-31181A AA64-70117B AA64-40487A AA64-10750A AA61-60003A L3113-0003-011 AA64-40509A LA95-90026X AA60-10002A AA64-10749A 6002-000514 6002-000514 3001-001071 AA03-10026R AA60-10050R AA65-30004A 3704-000114 AA64-31183A 6002-000516 AA39-10007Y
Description FRONT-CABINET BADGE-BRAND WINDOW-REMOTE KNOB-POWER SPRING-CS BOSS-CABINET INDICATOR-LED ASSY-PCB,A/V SCREW-TAPPING KNOB-CONTROL SCREW-TAPPING SCREW-TAPPING SPEAKER CRT-COLOR SCREW-ASSY CLAMP-D,COIL SOCKET CRT CABINET-BACK SCREW-TAPPING POWER-CORD
Specification HIPS VO BLK CT-762 AL,SS,R2000,25,SILVER CT-633 PC VIOLET CT-762 ABS HB GRAY G3676 TACT -,-,SUS304,0.5,OD7,H16,N7,-,HIPSVOBLKCT-5073 ACRYL CLR CT-762 CT-683B,KCT57A,NTSC,100 -,RH,+,M4,L12,ZP ABS HB GRAY G3676 RH,+,2,M4,L15,ZP RH,+,2,M4,L15,ZP 5W,8OHM,90DB,180HZ A70QBZ791X001,+380MG,29,100 WC,HH,+M5,L31.5,SWR -,NYLON-66,V0,WHT 14P,29.1,35.5SN,1SH09S/BK HIPS VO GRAY CT-762 RH,+,2,M4,L20,ZP -,EP2/YES,SPT-2 18AWGx2C,2.4m
Q'ty 1 1 1 1 1 1 1 1 2 1 2 4 2 1 4 8 1 1 7 1
Remark
AV+CF KC+CF SPK+CF
CRT+CF V999
CB+CF
Samsung Electronics
5-11
Electric Parts List
6. Electric Parts List
6-1 TXJ2060 (TXJ2067 and TXJ2060 Dissimilar Parts)
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-PCB,MAIN
* SF101 JA701 C222 C235 R618 R623 L217 AA94-10147G 2904-000304 3722-001192 2202-000279 2202-000279 2001-000812 2001-000812 2701-000158 ASSY-PCB,MAIN;TXJ2060,K51A,MONO,USA,SECA FILTER-SAW;M1859MNTSC/USAVIFS JACK RCA;2P(9P),3.4MM,SN,BLK#1622 C-CERAMIC,MLC-AXIAL;47PF,5%,5 C-CERAMIC,MLC-AXIAL;47PF,5%,5 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2mm INDUCTOR-AXIAL;22UH,10%,2.5X3 AA68-00057B AA68-11371A
ASSY-ACCESSORY
MANUAL-USERS;K51A,ENG,µfiÇ¥Áö2~1µµ,B5,W/P MANUAL-USERS;K51A,FRE,TM58,B5,W/P 100(G)
ASSY-CABINET,FRONT
AA92-30152G AA92-30152H AA64-60278H AA64-60417B ASSY-CABINET,FRONT;K51A,SEA,MONO,TXJ2060 ASSY-CABINET,FRONT;K51A,SECA,MONO,2060 INLAY-AV;-,K51A,MONO,PS,T0.5,BLK, INLAY-BACK;K51A,MONO,BL/G,P SEA SECA
REMOCON
* * AA59-10112F AA59-10112K REMOCON;DP,TM58,-,-,AA59-10109E,-,-,-, REMOCON;DP,-,TM58,AA59-10109J,-,-,-,-, SEA SECA
ASSY-PCB,A/V
* LA97-90003P 3722-001282 ASSY-PCB,A/V;-,K51A,MONO,JACK JACK-RCA;2P(3P),3.2mm,AU,BLK,
6-2 TXJ2066 (TXJ2067 and TXJ2066 Dissimilar Parts)
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
REMOCON
AA59-10113B AA59-10113H REMOCON;DP,TM59,-,-,-,-,-,AA59-10110B, REMOCON;DP,TM59,-,-,-,-,-,AA59-10110H, SEA SECA
ASSYCABINET,FRONT
AA92-30152B ASSYCABINET,FRONT;TXJ2066,SEC
ASSY-ACCESSORY
AA68-00057B AA68-11371A MANUAL-USERS;K51A,ENG,2~1µµ,B5,W/P MANUAL-USERS;K51A,FRE,TM58,B5,W/P 100(G) SECA SECA
Samsung Electronics
6-1
Electric Parts List
6-3 TXJ2067/UCX
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-PCB,MAIN
A/MAIN AA94-10147F C101 C102 C104 C105 C106 C107 C108 C110 C111 C112 C113 C116 C117 C202 C203 C204 C205 C210 C211 C212 C213 C217 C223 C224 C225 C226 C227 C228 C229 C230 C232 C233 C234 C235 C237 C239 C240 C242 C243 C244 C250 C302 C303 C304 C305 C306 C308 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C417 C501 C503 C504 C505 C506 2401-000962 2401-001363 2202-000127 2401-001333 2202-000127 2401-001333 2401-000480 2401-001840 2202-000286 2202-000127 2202-000127 2202-000127 2202-000127 2305-000665 2305-000665 2401-000660 2301-000224 2401-001840 2305-000665 2202-002037 2305-000665 2202-000819 2201-000258 2301-000445 2305-000665 2401-001840 2305-000665 2401-000660 2301-000342 2202-000162 2301-000445 2401-000603 2309-000138 2202-000286 2305-000665 2401-000603 2201-000379 2401-000480 2201-000483 2401-000660 2301-000383 2401-000360 2305-000149 2305-000285 2201-000259 2401-000360 2301-000254 2201-000599 2306-000327 2201-000406 2306-000195 2301-000213 2201-000556 2401-001397 2201-000556 2401-001397 2401-002268 2201-000556 2401-000927 2401-002619 2201-000984 2303-000331 2301-000383 2305-000704 2401-001232 2202-000121 2202-000121 2202-000121 ASSY-PCB,MAIN;TXJ2066/67,K51A,USA/SECA C-AL;22uF,20%,50V,GP,TP,5x11,5 C-AL;470UF,20%,16V,GP,TP,10X12 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-ELECTROLYTIC;CE04WTAPG50V0.4 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-ELECTROLYTIC;CE04WTAPG50V0.4 C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;100UF,20%,16V,GP,TP,6.3X1 C-CERAMIC,MLC-AXIAL;56PF,5%,50 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-FILM;CF922N63VT104-J-40/1053 C-FILM;CF922N63VT104-J-40/1053 C-ELECTROLYTIC;CE04WTAPG50V2.2 C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-AL;100UF,20%,16V,GP,TP,6.3X1 C-FILM;CF922N63VT104-J-40/1053 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-FILM;CF922N63VT104-J-40/1053 C-CERAMIC,MLC-AXIAL;47NF,+80-2 C-CERAMIC,DISC;17PF,5%,50V,NPO,-,5MM,TP C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM;CF922N63VT104-J-40/1053 C-AL;100UF,20%,16V,GP,TP,6.3X1 C-FILM;CF922N63VT104-J-40/1053 C-ELECTROLYTIC;CE04WTAPG50V2.2 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm, C-CERAMIC,MLC-AXIAL;15PF,5%,50 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;1UF,20%,50V,GP,5X11MM,5MM C-FILM,PE-PPF;100NF,5%,50V,TP, C-CERAMIC,MLC-AXIAL;56PF,5%,50 C-FILM;CF922N63VT104-J-40/1053 C-AL;1UF,20%,50V,GP,5X11MM,5MM C-CERAMIC,DISC;22NF,+80-20%,50 C-AL;10UF,20%,50V,GP,5X11MM,5M C-CERAMIC,DISC;33PF,5%,50V,NPO C-ELECTROLYTIC;CE04WTAPG50V2.2 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-AL;100UF,20%,50V,GP,8X11MM,5 C-FILM;CF922N100VT104-J-40/105 C-FILM,MPEF;220NF,5%,100V,-,5M C-CERAMIC,DISC;180PF,10%,500V,Y5P,6X4MM, C-AL;100UF,20%,50V,GP,8X11MM,5 C-FILM,PEF;39NF,5%,50V,7.5X3.5X6.5MM,5MM C-CERAMIC,DISC;560PF,10%,500V, C-FILM;CF922P1.6KVT632-H-25/85 C-CERAMIC,HIC;CK45(T)B2KV271-K C-FILM,MPPF;360NF,5%,400V,26.0 C-FILM,PEF;220NF,5%,250V,21.5X C-CERAMIC,DISC;470PF,10%,500V, C-AL;470UF,20%,25V,GP,10X16MM, C-CERAMIC,DISC;470PF,10%,500V, C-AL;470UF,20%,25V,GP,10X16MM, C-ELEC;CE04-40/105250VT2R2-MWR C-CERAMIC,DISC;470PF,10%,500V, C-AL;22UF,20%,250V,GP,13X20MM, C-AL;47uF,20%,25V,GP,TP,5x11,5 C-CERAMIC,DISC;680PF,10%,2KV,Y C-FILM;4.7NF,5%,630V,19.5X12X7 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-M,POLYESTER;CFS922MTAPG250V1 C-AL;4.7UF,20%,250V,GP,10X12.5 C-CERAMIC,MLC-AXIAL;100PF,10%, C-CERAMIC,MLC-AXIAL;100PF,10%, C-CERAMIC,MLC-AXIAL;100PF,10%,
!
! !
!
C510 C518 C520 C610 C627 C628 C629 C631 C632 C634 C650 C651 C701 C702 C703 C704 C706 C707 C708 C709 C712 C713 C714 C715 C716 C717 C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C815 C816 C817 C820 C821 C822 C823 C825 C827 C834 C855 C861 C862 C873 C890 C891 C901 C902 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C920 CB01 CD10 CD11
2401-002264 2201-002063 2202-000862 2301-000192 2401-000603 2401-000471 2401-000027 2401-000603 2401-000471 2401-001998 2202-000796 2202-000796 2401-000480 2401-000302 2401-000603 2401-000603 2401-000027 2401-000480 2401-000480 2401-000027 2305-000708 2305-000355 2305-000355 2305-000708 2301-000289 2301-000289 2401-001387 2201-000332 2201-000332 2303-000163 2201-000991 2401-003026 2201-000599 2401-001571 2401-000302 2401-000611 2401-000302 2401-000302 2401-002144 2401-003058 2401-000164 2202-002037 2401-000164 2201-000990 2201-000963 2201-000990 2301-000310 2301-000224 2401-002288 2201-000599 2401-000287 2401-000480 2401-000302 2201-000374 2201-000292 2401-002144 2202-000796 2401-002144 2202-000796 2401-001333 2202-000121 2401-002144 2201-000573 2201-000193 2201-000119 2401-000302 2301-000383 2202-000127 2202-000286 2202-000263 2306-000318 2401-000603 2401-001989
C-AL;10UF,20%,350V,GP,TP,10X20 C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,1 C-CERAMIC;CCOASL50VT391-JUP050 C-FILM,PEF;1NF,5%,50V,5.3X10MM C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;10UF,20%,50V,BP,6X11MM,5M C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;10UF,20%,50V,BP,6X11MM,5M C-AL;1000UF,20%,25V,GP,TP,10X20 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;100UF,20%,25V,GP,6X11MM,5 C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-FILM;CF922N100VT154-J-40/105 C-FILM,MPEF;330NF,5%,63V,-,5MM C-FILM,MPEF;330NF,5%,63V,-,5MM C-FILM;CF922N100VT154-J-40/105 C-FILM,PEF;5.6NF,5%,50V,6.5X5. C-FILM,PEF;5.6NF,5%,50V,6.5X5. C-AL;470uF,20%,250V,GP,BK,25.4x40,1 C-CERAMIC,AC;CK45PTAPGE250V222 C-CERAMIC,AC;CK45PTAPGE250V222 C-FILM,PPF;2.2NF,5%,800V,-,-,T C-CERAMIC,HIC;CK45(T)B2KV561-K C-AL;330UF,20%,200V,GP,ST,22X3 C-CERAMIC,DISC;560PF,10%,500V, C-ELECTROLYTIC;CE04WTAPG50V47C-AL;100UF,20%,25V,GP,6X11MM,5 C-AL;1UF,20%,50V,WT,5X11MM,5MM C-AL;100UF,20%,25V,GP,6X11MM,5 C-AL;100UF,20%,25V,GP,6X11MM,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;100UF,20%,200V,WT,16X25MM C-ALUMINUM;1000UF,20%,25V,WT,TP,12.5X20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-ALUMINUM;1000UF,20%,25V,WT,TP,12.5X20 C-CERAMIC,AC;ECK-ZNS472MEX(RO) C-CERAMIC;CK45Y5U400VACT102-MH C-CERAMIC,AC;ECK-ZNS472MEX(RO) C-FILM,PEF;68NF,5%,50V,8.0X8.5 C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-ELEC;CE04-55/10525VT471-MWRG C-CERAMIC,DISC;560PF,10%,500V, C-AL;100UF,20%,16V,WT,6X11MM,5 C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;100UF,20%,25V,GP,6X11MM,5 C-CERAMIC,DISC;220pF,5%,50V,CH,TP,12.5x3 C-CERAMIC,DISC;1NF,10%,50V,Y5P C-AL;47uF,20%,16V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-ELECTROLYTIC;CE04WTAPG50V0.4 C-CERAMIC,MLC-AXIAL;100PF,10%, C-AL;47uF,20%,16V,GP,TP,5x11,5 C-CERAMIC,DISC;47PF,5%,50V,NPO C-CERAMIC,DISC;10PF,0.25PF,50V C-CERAMIC,DISC;100NF,+80-20%,5 C-AL;100UF,20%,25V,GP,6X11MM,5 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;56PF,5%,50 C-CERAMIC,MLC-AXIAL;470PF,10%,50V,Y5P,3. C-FILM,MPPF;220NF,20%,250V,-,2 C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;4.7uF,20%,50V,BP,TP,5x11,5
6-2
Samsung Electronics
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
!
CD12 CD26 CN501B CN601 CN602 CN701 CORD/H CORD/P CP01 CP02 CP03 CP04 CP05 CU02 CU06 CU11 CU12 CU13 CU33 CUD06 CUD08 CUD09 CUD15 CUD18 CUD20 CUD21 CUD23 CUD24 CUD25 CUD28 CUD29 CUD30 CX01 D201 D202 D204 D205 D206 D207 D208 D210 D301 D401 D402 D403 D404 D405 D503 D511 D512 D513 D601 D801 D803 D804 D810 D812 D814 D825 D903 D908 D910 D951 D962 DU01 DU02 DU03 DX01 DZ101 DZ217 DZ231 DZ250 DZ302 DZ303 DZ304 DZ305 DZ306
2401-000480 2401-001026 AA39-20604A 3711-002643 3711-002644 3711-002648 AA61-20284A AA39-10007Y 2301-000224 2301-000224 2305-000665 2305-000665 2401-001496 2202-002037 2401-000480 2202-002037 2202-002037 2202-002037 2401-001989 2401-001989 2301-000289 2301-000160 2401-000027 2401-001840 2401-001989 2401-000027 2401-001989 2301-000204 2301-000356 2401-001989 2401-000480 2401-000603 2401-000480 0401-000005 0402-000132 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-001105 0402-000493 0402-000132 0402-000132 0402-000540 0402-001105 0402-000132 0402-001105 0402-001105 0402-001105 0401-000005 0402-001082 0402-000493 0402-001105 0402-000493 0402-000231 0402-000213 0402-000493 0401-000005 0401-000005 0401-000005 0402-000132 0401-000005 0401-000005 0401-000005 0401-000005 0402-001105 0403-000700 0403-000563 0403-000563 0403-000662 0403-000660 0403-000660 0403-000660 0403-000494 0403-000700
C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;3.3UF,20%,50V,GP,5X11MM,5 LEAD CONNECTOR-ASSY;-,YBNH250-09,YBNH05/ POST-HEADER;YW025-04(AUTO) POST-HEADER;67094-005(AUTO) POST-HEADER;67094-009(AUTO) HOLDER P CORD;PP,VO,BLK,KE-002 POWER-CORD;-,EP2/YES,SPT-2 18AWGx2C,2.4m C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM;CF922N63VT104-J-40/1053 C-FILM;CF922N63VT104-J-40/1053 C-AL;47UF,20%,16V,GP,5X7MM,5MM C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-AL;10UF,20%,50V,GP,5X11MM,5M C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-FILM,PEF;5.6NF,5%,50V,6.5X5. C-FILM,PEF;12NF,5%,50V,11.0X6. C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;100UF,20%,16V,GP,TP,6.3X1 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-FILM,PEF;2.7NF,5%,50V,7.4X3. C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;10UF,20%,50V,GP,5X11MM,5M DIODE;1N4148TAPG DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;1R5GU41,400V,1 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;RU20A,600V,1.5 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE;1N4148TAPG DIODEBRIDGE;RBV406LFB,600V,4A DIODE-RECTIFIER;1R5GU41,400V,1 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;1R5GU41,400V,1 DIODE-RECTIFIER;FMG-G26S,600V, H/SINK DIODE-RECTIFIER;ERB12-06,600V, DIODE-RECTIFIER;1R5GU41,400V,1 DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE;1N4148TAPG DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-ZENER;TZP33A,33V,31-35V, DIODE-ZENER;MTZ9.1B,9.1V,8.57DIODE-ZENER;MTZ9.1B,9.1V,8.57DIODE-ZENER;MTZ3.0B,3.0V,3.01DIODE-ZENER;MTZ22A,22V,20.15-2 DIODE-ZENER;MTZ22A,22V,20.15-2 DIODE-ZENER;MTZ22A,22V,20.15-2 DIODE-ZENER;MTZ39B,39V,35.36/3 DIODE-ZENER;TZP33A,33V,31-35V,
!
!
DZ401 DZ402 DZ505 DZ601 DZ612 DZ613 DZ621 DZ622 DZ707 DZ708 DZ801 DZ802 DZ803 DZ804 DZ805 DZ806 DZ807 DZ808 DZ810 DZ864 DZ901 DZ902 DZ905 DZ906 DZ907 DZ908 DZ910 DZX01 F801 F801A F801B GT102 IC201 IC202 IC301 IC501 IC603 IC701 IC801 IC802 IC851 IC852 IC853 IC901 IC902 ICD01 ICP01 J258 JA701 L102 L103 L104 L201 L202 L203 L204 L205 L206 L237 L401 L405 L406 L602 L710 L802 L807 L808 L809 L810 L811 L812 L814 L815 L816 L864 L901 L902
0403-000300 0403-000355 0403-000563 0403-000563 0403-000656 0403-000656 0403-000656 0403-000656 0403-000563 0403-000563 1405-001036 1405-001036 0403-000300 0403-000296 0403-000296 0403-000562 0403-000297 0403-000296 0401-000005 0403-000296 0403-000355 0403-000562 0403-000297 0403-000297 0403-000297 0403-000297 0403-000297 0403-000667 3601-001012 3602-000114 3602-000114 AA39-20010B 1204-001174 1204-000506 1204-000517 1201-001330 1201-001308 1204-001455 1203-001482 1203-000644 0604-001038 1203-001217 1203-001225 AA13-00017A 1103-001106 1209-001116 1209-000214 2001-000780 3722-001103 2701-000142 2701-000207 2701-000114 2701-000127 3301-000287 3301-000287 2701-000114 2701-000114 2701-000114 2701-000114 AA27-30001B 2701-000142 2901-000297 3301-000287 2701-000114 AA29-30002F 3301-000287 3301-001223 3301-001223 AA27-10002Y 2901-000297 2901-000297 2901-000297 3301-000287 2701-001032 3301-000287 2701-000114 2701-000114
DIODE-ZENER;MTZ8.2B,7.78-.19V, DIODEZENER;UZ5.1BSB,4.97~5.17V,0.5UA,500 DIODE-ZENER;MTZ9.1B,9.1V,8.57DIODE-ZENER;MTZ9.1B,9.1V,8.57DIODE-ZENER;MTZ15C,15V,14.35-1 DIODE-ZENER;MTZ15C,15V,14.35-1 DIODE-ZENER;MTZ15C,15V,14.35-1 DIODE-ZENER;MTZ15C,15V,14.35-1 DIODE-ZENER;MTZ9.1B,9.1V,8.57DIODE-ZENER;MTZ9.1B,9.1V,8.57VARISTOR;430V,2500A,14x8.5mm,TP VARISTOR;430V,2500A,14x8.5mm,TP DIODE-ZENER;MTZ8.2B,7.78-.19V, DIODE-ZENER;EQA02-06A/MTZ5.6B( DIODE-ZENER;EQA02-06A/MTZ5.6B( DIODE ZENER;MTZ7.5B,7.5V,7.07-7-45V,500M DIODE-ZENER;EQA02-06D/MTZ6.2B( DIODE-ZENER;EQA02-06A/MTZ5.6B( DIODE;1N4148TAPG DIODE-ZENER;EQA02-06A/MTZ5.6B( DIODEZENER;UZ5.1BSB,4.97~5.17V,0.5UA,500 DIODE ZENER;MTZ7.5B,7.5V,7.07-7-45V,500M DIODE-ZENER;EQA02-06D/MTZ6.2B( DIODE-ZENER;EQA02-06D/MTZ6.2B( DIODE-ZENER;EQA02-06D/MTZ6.2B( DIODE-ZENER;EQA02-06D/MTZ6.2B( DIODE-ZENER;EQA02-06D/MTZ6.2B( DIODE-ZENER;MTZ6.8A,6.8V,6.29FUSE-FERRULE;250V,4A,SLOW-BLOW FUSE-HOLDER;-,-,30MOHM FUSE-HOLDER;-,-,30MOHM LEAD-CONNECTOR,ASSY;-,YFH800-01,500MM,1P ICHOR/VERPROCESS;TDA8373A,DIP, IC-LINEAR;LA7510SIP9P IC-LINEAR;LA7845SIPVERTICALAMP IC-VIDEO;TDA6108JF,ZSIP,9,SINGLE,IC-POWERAMP;7266,ZIP,15P,-,DUAL,26dB,PL IC-VOLUME/TONECONT.;TDA7449,DIP,20P,300 IC-PWMCONTROLLER;3S1265R,TO-3P,5P,210,P IC-POSI.FIXEDREG.;7630,SIP,10P PHOTOCOUPLER;TR,130-260%,200MW IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P IC-POSI.FIXEDREG.;78R09,TO-220,4P,-,PLA IC-MCU;-,Z9036512PSC-R4127 IC-EEPROM;24C080,1028x8BIT,DIP,8P,300MIL IC-ETC,LINEAR;CXA2104S,DIP,30P,-,PLASTI IC-DELAYLINE;TDA4665,DIP,16P,300MIL,PLA R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm JACKRCA;5P INDUCTOR-AXIAL;1UH,10%,2.5X3.4 INDUCTOR-AXIAL;56UH,5%,2.5X3.4 INDUCTOR-AXIAL;10UH,10%,2.5X3. INDUCTOR-AXIAL;15UH,10%,2.5X3. CORE-FERRITEBEAD;AA,3.5X1.0X6. CORE-FERRITEBEAD;AA,3.5X1.0X6. INDUCTOR-AXIAL;10UH,10%,2.5X3. INDUCTOR-AXIAL;10UH,10%,2.5X3. INDUCTOR-AXIAL;10UH,10%,2.5X3. INDUCTOR-AXIAL;10UH,10%,2.5X3. COIL-LINEARITY;-,195UH,QIC1010 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITEBEAD;AA,3.5X1.0X6. INDUCTOR-AXIAL;10UH,10%,2.5X3. FILTER-LINENOISE;-,6MH,2.45A,CORE-FERRITEBEAD;AA,3.5X1.0X6. CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP, CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP, COIL-CHOKE;-,100UH,K,10,700MA, FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITEBEAD;AA,3.5X1.0X6. INDUCTOR-AXIAL;100UH,10%,5X14MM CORE-FERRITEBEAD;AA,3.5X1.0X6. INDUCTOR-AXIAL;10UH,10%,2.5X3. INDUCTOR-AXIAL;10UH,10%,2.5X3.
H/SINK H/SINK H/SINK H/SINK H/SINK
Samsung Electronics
6-3
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
L903 LA01 LD901 LK803 LUD01 NT801 PUD01 Q101 Q201 Q204 Q401 Q402 Q601 Q604 Q901 Q902 Q951 QP01 QP02 QU03 QU05 QX01 R102 R103 R104 R107 R108 R109 R111 R112 R113 R114 R120 R200 R202 R204 R205 R206 R207 R209 R210 R211 R212 R213 R214 R215 R216 R217 R219 R222 R223 R224 R226 R228 R229 R230 R231 R232 R233 R234 R235 R237 R239 R245 R250 R251 R252 R253 R260 R301 R302 R303 R304 R306 R309 R403 R405
3301-000287 AA27-10002X AA96-30001B AA29-30002F 2701-000106 1404-001045 1404-000208 0501-000436 0501-000389 0501-000283 0502-001115 0501-000369 0501-000389 0501-000389 0504-000123 0501-000389 0501-000369 0501-000389 0501-000389 0504-000123 0501-000283 0501-000283 2001-000591 2001-000660 2001-000221 2001-000281 2001-000281 2001-000938 2001-000793 2001-000281 2001-000577 2001-000221 2001-000490 2001-000577 2001-000005 2001-000793 2001-000325 2001-000281 2001-000325 2001-000281 2001-000281 2001-000766 2001-000617 2001-000429 2001-000281 2001-000281 2001-000281 2001-000273 2001-000679 2001-000780 2001-000252 2001-000734 2001-000273 2004-001089 2001-000938 2001-000591 2001-000281 2001-000440 2001-000539 2001-000008 2001-000522 2004-001914 2001-000864 2001-000273 2001-000066 2001-000531 2001-001062 2001-001411 2001-000832 2001-001172 2001-001172 2001-000016 2003-002014 2003-002069 2003-002069 2001-001114 2003-000540
CORE-FERRITEBEAD;AA,3.5X1.0X6. COIL-CHOKE;-,43UH,K,10,1A,T,43 ASSY-LED,GUIDE;-,AA61-50055A,D FILTER-LINENOISE;-,6MH,2.45A,INDUCTOR-AXIAL;1.5uH,10%,2.8x7mm THERMISTOR NTC;4.7OHM,15%,2900K,35.0MW,T POSISTOR;PTH631D02BF7ROM140TDE TR-SMALLSIGNAL;KTC3197,NPN,30V TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSA539-Y(TAPG)/YTAM TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8 TRANSISTOR;KSC2331-Y(TAPG) TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TR-DIGITAL;KSR1010,NPN,300MW,1 TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC2331-Y(TAPG) TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TR-DIGITAL;KSR1010,NPN,300MW,1 TRANSISTOR;KSA539-Y(TAPG)/YTAM TRANSISTOR;KSA539-Y(TAPG)/YTAM R-CARBON;3.3KOHM,5%,1/8W,AA,TP R-CARBON;33KOHM,5%,1/8W,AA,TP, R-CARBON;1.2KOHM,5%,1/8W,AA,TP R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-METAL;68ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;47OHM,5%,1/8W,AA,TP,1 R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;2KOHM,5%,1/8W,AA,TP,1 R-CARBON;1.2KOHM,5%,1/8W,AA,TP R-CARBON;200OHM,5%,1/8W,AA,TP, R-CARBON;2KOHM,5%,1/8W,AA,TP,1 R-CARBON;390OHM,5%,1/8W,AA,TP, R-CARBON;47OHM,5%,1/8W,AA,TP,1 R-CARBON;120OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;120OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;43KOHM,5%,1/8W,AA,TP, R-CARBON;3.9MOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100KOHM,5%,1/8W,AA,TP R-CARBON;36KOHM,5%,1/8W,AA,TP, R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1.6KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;100KOHM,5%,1/8W,AA,TP R-METAL;560KOHM,5%,1/8W,AA,TP, R-METAL;68ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;3.3KOHM,5%,1/8W,AA,TP R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;1OHM,5%,1/8W,AA,TP,1. R-CARBON;24KOHM,5%,1/8W,AA,TP, R-CARBON;15KOHM,5%,1/8W,AA,TP, R-CARBON;22KOHM,5%,1/8W,AA,TP, R-METAL;39KOHM,2%,1/8W,AA,TP,1 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;100KOHM,5%,1/8W,AA,TP R-CARBON(S);10KOHM,5%,1/2W,AA, R-CARBON;240KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON(S);10MOHM,5%,1/2W,AA, R-CARBON;5.6Mohm,5%,1/8W,AA,TP,1.7x3.2m R-CARBON;510OHM,5%,1/8W,AA,TP, R-CARBON(S);620OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);620OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);1OHM,5%,1/2W,AA,TP R-METALOXIDE(S);0.6OHM,5%,2W,A R-METALOXIDE;470OHM,5%,2W,AF,T R-METALOXIDE;470OHM,5%,2W,AF,T R-CARBON(S);270OHM,5%,1/2W,AA, R-METALOXIDE(S);1KOHM,5%,2W,AD
! ! !
!
!
R406 R407 R408 R409 R410 R411 R412 R413 R415 R416 R418 R419 R501 R502 R503 R504 R505 R506 R517 R518 R519 R520 R523 R524 R525 R526 R601 R602 R603 R606 R607 R608 R610 R617 R618 R619 R622 R623 R624 R707 R708 R709 R713 R714 R715 R719 R720 R802 R803 R804 R805 R806 R807 R808 R810 R811 R814 R819 R820 R822 R826 R827 R828 R830 R831 R832 R833 R836 R861 R862 R901 R902 R903 R904 R905 R906 R907
2003-002008 2001-000022 2004-001390 2008-001011 2008-001011 2004-001373 2004-001373 2003-002101 2003-002007 2001-000613 2008-000254 2008-000252 2001-000490 2001-000490 2001-000490 2001-000449 2001-000449 2001-000449 2002-001009 2002-001009 2002-001009 2001-000096 2008-000299 2002-001006 2008-000266 2008-000254 2001-000429 2001-000290 2004-000195 2001-000281 2001-000429 2001-000281 2001-000429 2001-000429 2001-000290 2001-000281 2001-000429 2001-000290 2001-000281 2001-000429 2001-000085 2001-000429 2001-000577 2001-000577 2001-001187 2001-000281 2001-000281 2001-001150 2003-000994 2003-000994 2002-001013 2001-001071 2001-001071 2004-004089 2001-001150 2001-001153 2001-001050 2001-001178 2003-001047 2001-000273 2001-001125 2001-001093 2004-001983 2008-001011 2008-001011 2003-000458 2003-001035 2008-000266 2008-001033 2008-001033 2001-000793 2001-000429 2001-000281 2001-000281 2001-000290 2001-000472 2001-000995
R-METAL OXIDE(S);18KOHM,5%,2W,AF,TP,3.9X R-CARBON(S);33OHM,5%,1/2W,AA,T R-METAL(S);1KOHM,2%,1/2W,AA,TP R-FUSIBLE(S);0.18OHM,10%,2W,AF R-FUSIBLE(S);0.18OHM,10%,2W,AF R-METAL,FILM;RM1/2T100K-F R-METAL,FILM;RM1/2T100K-F R-METAL OXIDE;82OHM,5%,2W,AF,TP,4X12MM R-METAL OXIDE(S);4.7KOHM,5%,2W,AF,TP,3.9 R-CARBON;3.9KOHM,5%,1/8W,AA,TP R-FUSIBLE(S);0.68OHM,5%,2W,AF, R-FUSIBLE(S);0.47OHM,10%,1/2W, R-CARBON;200OHM,5%,1/8W,AA,TP, R-CARBON;200OHM,5%,1/8W,AA,TP, R-CARBON;200OHM,5%,1/8W,AA,TP, R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7 R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7 R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7 R-CARBON(S);1MOHM,5%,1/2W,AA,T R-FUSIBLE;RF2RT470-J R-COMPOSITION;RC1/2T4.7KK/ERCR-FUSIBLE(S);1OHM,5%,2W,AF,TP, R-FUSIBLE(S);0.68OHM,5%,2W,AF, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;10KOHM,5%,1/8W,AA,TP, R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON(S);100KOHM,5%,1/2W,AA R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;2KOHM,5%,1/8W,AA,TP,1 R-CARBON;2KOHM,5%,1/8W,AA,TP,1 R-CARBON(S);75OHM,5%,1/2W,AA,T R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON(S);470KOHM,5%,1/2W,AA R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1 R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1 R-COMPOSITION;4.7MOHM,10%,1/2W,AA,TP,3.7 R-CARBON(S);12KOHM,5%,1/2W,AA, R-CARBON(S);12KOHM,5%,1/2W,AA, R-METAL;123KOHM,1%,1/2W,AA,TP,2.5X6.5 R-CARBON(S);470KOHM,5%,1/2W,AA R-CARBON(S);47OHM,5%,1/2W,AA,T R-CARBON(S);1.5KOHM,5%,1/2W,AA R-CARBON(S);680OHM,5%,1/2W,AA, R-METAL OXIDE(S);68OHM,5%,2W,AF,TP,3.9X1 R-CARBON;100KOHM,5%,1/8W,AA,TP R-CARBON(S);300KOHM,5%,1/2W,AA R-CARBON(S);2.2KOHM,5%,1/2W,AA R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4 R-FUSIBLE(S);0.18OHM,10%,2W,AF R-FUSIBLE(S);0.18OHM,10%,2W,AF R-METALOXIDE(S);100OHM,5%,2W,A R-METALOXIDE(S);27OHM,5%,2W,AF R-FUSIBLE(S);1OHM,5%,2W,AF,TP, R-FUSIBLE(S);10OHM,5%,2W,AF,TP R-FUSIBLE(S);10OHM,5%,2W,AF,TP R-CARBON;47OHM,5%,1/8W,AA,TP,1 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;820OHM,5%,1/8W,AA,TP,
6-4
Samsung Electronics
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
! ! ! ! !
R908 R909 R911 R912 R914 R915 R918 R920 R921 R922 R923 R924 R925 R926 R927 R928 R930 R931 R932 R935 R951 R952 R953 R956 R957 R958 R959 R961 R962 R964 R965 R966 RA01 RA02 RL801 RM901 RN01 RP01 RP02 RP03 RP04 RU01 RU03 RU04 RU05 RU06 RU07 RU08 RU09 RU10 RU12 RU13 RU14 RU15 RU16 RU17 RU18 RU19 RU20 RUD03 RUD04 RUD08 RUD09 RUD13 RUD24 RUD25 RUD30 RUD40 RUD41 RUD42 RUD43 RX01 RX02 RX03 RX04 RX05 SF101
2001-000232 2001-000449 2001-000290 2001-000832 2001-000490 2001-000241 2001-000429 2001-000734 2001-001062 2701-000114 2701-000114 2001-000449 2001-000449 2001-000449 2001-000290 2004-001234 2001-000832 2001-000010 2001-001062 2001-000832 2001-000290 2001-000472 2001-000947 2001-000290 2001-000117 2001-000241 2001-000734 2001-000766 2001-000290 2004-001390 2001-000273 2001-000290 2003-000458 2003-000458 3501-001040 AA59-60001U 2001-000995 2001-000429 2001-000429 2001-000429 2001-000429 2002-001010 2001-000290 2001-000577 2001-000577 2001-000577 2001-000429 2001-000005 2001-000005 2001-000005 2001-000290 2001-000613 2004-001989 2004-001989 2004-001989 2001-000429 2001-000429 2001-000429 2001-000429 2001-000281 2001-000281 2001-000435 2001-000273 2004-001165 2001-000591 2001-000007 2001-000613 2001-000429 2001-000947 2001-000429 2001-000947 2001-000397 2001-000522 2001-000522 2001-000766 2001-000313 2904-000287
R-CARBON;1.3KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;510OHM,5%,1/8W,AA,TP, R-CARBON;200OHM,5%,1/8W,AA,TP, R-CARBON;1.5KOHM,5%,1/8W,AA,TP R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON(S);10MOHM,5%,1/2W,AA, INDUCTOR-AXIAL;10UH,10%,2.5X3. INDUCTOR-AXIAL;10UH,10%,2.5X3. R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;10KOHM,5%,1/8W,AA,TP, R-METAL;75KOHM,5%,1/8W,AA,TP,1 R-CARBON;510OHM,5%,1/8W,AA,TP, R-CARBON;68Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON(S);10MOHM,5%,1/2W,AA, R-CARBON;510OHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;7.5KOHM,5%,1/8W,AA,TP R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m R-CARBON;1.5KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;43KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-METAL(S);1KOHM,2%,1/2W,AA,TP R-CARBON;100KOHM,5%,1/8W,AA,TP R-CARBON;10KOHM,5%,1/8W,AA,TP, R-METALOXIDE(S);100OHM,