av-30w575s.pdf part of JVC AV-30W585 av-30w575s.pdf, Complete Service Manual text manual preview

Text preview for : av-30w575s.pdf part of JVC AV-30W585 Complete Service Manual

Back to : av-30w575s.pdf | Home

SERVICE MANUAL
COLOR TELEVISION
7 2004 YA094

AV-30W575/S, AV-30W585/S
BASIC CHASSIS

SC2

[AV-30W585]

TABLE OF CONTENTS
1 2 3 4 5 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-39

COPYRIGHT © 2004 Victor Company of Japan, Limited

No.YA094 2004/7

SPECIFICATION
Items Dimensions ( W × H × D ) Mass TV RF System Color System Sound System Teletext System TV Receiving Channels and Frequency Contents AV-30W575 AV-30W585 84.2cm × 59.9cm × 55.5cm (33-1/8" × 23-5/8" × 21-7/8") 54.0kg (118.8lbs) CCIR (M) NTSC BTSC (Multi Channel Sound) Closed caption (T1-T4 / CC1-CC4) 02ch to 06ch : 54MHz to 88MHz 07ch to 13ch : 174MHz to 216MHz 14ch to 69ch : 470MHz to 806MHz 54MHz to 804MHz Low Band : 02 to 06, A-8 by 02 to 06&01 High Band : 07 to 13 by 07 to 13 Mid Band : A to I by 14 to 22 Super Band : J to W by 23 to 36 Hyper Band : W+1 to W+28 by 37 to 64 Ultra Band : W+29 to W+84 by 65 to 94, 100 to 125 Sub Mid Band : A4 to A1 by 96 to 99 181 Channels

VHF Low VHF High UHF CATV

TV / CATV Total Channel

NOTE: Reception of channel A-5 ("95" of the TV set's on-screen CABLE channel) is recommended for yuor TV set. Intermediate Frequency Video IF 45.75 MHz Sound IF 41.25 MHz (4.5MHz) Color Sub Carrier 3.58 MHz Power Input AC120V, 60Hz Power Consumption 215W Picture Tube (Visible size) 76cm (30") Measured diagonally (H: 67.4cm × V: 38.4cm) High Voltage 32kV(+1kV/-1.3kV) (at zero beam current) Speaker 6.5cm × 13cm (2-1/2" × 5") Audio Power Output 10W + 10W Antenna terminal (VHF/UHF) F-type connector, 75 unbalanced, coaxial Video / Audio input Component Video RCA pin jack × 6 [INPUT-1/2/3/4] [INPUT-1/2] 1080i / 720p Y : 1V (p-p) (Sync signal: 0.35V(p-p), 3-value sync.), 75 Pb/Pr : ±0.35V(p-p), 75 480p / 480i Y : 1V (p-p), Positive (Negative sync provided), 75 Cb/Cr : ±0.7V(p-p), 75 S-Video Mini-DIN 4 pin × 3 [INPUT-1/3/4] Y: 1V (p-p), Positive (Negative sync provided), 75 C: 0.286V (p-p) (Burst signal), 75 Video 1V (p-p), Positive (Negative sync provided), 75 , RCA pin jack × 4 Audio 500mV (rms), High impedance, RCA pin jack × 8 Digital input Video HDMI connector × 1 (Digital-input terminal is not compatible with picture signals of computer signal) Audio Digital: HDMI connector × 1 Analog: 500mV(rms) (-4dBs), high impedance, RCA pin jack × 2 Audio output RCA pin jack × 2 Variable More than 0 to 1000mV (rms) (+2.2dBs) Fix 500mV(rms), (-4dBs), low impedance (400Hz when modulated 100%) Subwoofer output More than 0 to 1000mV (rms) (+2.2dBs), low impedance (100Hz when modulated 100%), RCA pin jack × 1 Center channel input 500mV(rms) (-4dBs), high impedance,RCA pin jack × 1 AV compulink III --3.5mm mini jack × 1 Remote Control Unit RM-C1257G (AA/R6/UM-3 battery × 2) Design & specifications are subject to change without notice. 1-2 (No.YA094)

SECTION 1 PRECAUTION
1.1 SAFETY PRECAUTIONS
(10) Isolation Check (Safety for Electrical Shock Hazard) After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal cabinet, screw heads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. a) Dielectric Strength Test The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 1100V AC (r.m.s.) for a period of one second. (. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the service trade. b) Leakage Current Check Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current Tester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.). Alternate Check Method Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use an AC voltmeter having 1000 per volt or more sensitivity in the following manner. Connect a 1500 10W resistor paralleled by a 0.15µF AC-type capacitor between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER (HAVING 1000 /V, OR MORE SENSITIVITY)

(1) The design of this product contains special hardware, many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel only. (2) Alterations of the design or circuitry of the products should not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the parts list in Service manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement part shown in the parts list of Service manual may cause shock, fire, or other hazards. (4) Use isolation transformer when hot chassis. The chassis and any sub-chassis contained in some products are connected to one side of the AC power line. An isolation transformer of adequate capacity should be inserted between the product and the AC power supply point while performing any service on some products when the HOT chassis is exposed. (5) Don't short between the LIVE side ground and ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing. Some model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND, the ISOLATED (NEUTRAL) : ( ) side GND and EARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND and never measure the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND at the same time with a measuring apparatus (oscilloscope etc.). If above note will not be kept, a fuse or any parts will be broken. (6) If any repair has been made to the chassis, it is recommended that the B1 setting should be checked or adjusted (See B1 POWER SUPPLY check). (7) The high voltage applied to the picture tube must conform with that specified in Service manual. Excessive high voltage can cause an increase in X-Ray emission, arcing and possible component damage, therefore operation under excessive high voltage conditions should be kept to a minimum, or should be prevented. If severe arcing occurs, remove the AC power immediately and determine the cause by visual inspection (incorrect installation, cracked or melted high voltage harness, poor soldering, etc.). To maintain the proper minimum level of soft X-Ray emission, components in the high voltage circuitry including the picture tube must be the exact replacements or alternatives approved by the manufacturer of the complete product. (8) Do not check high voltage by drawing an arc. Use a high voltage meter or a high voltage probe with a VTVM. Discharge the picture tube before attempting meter connection, by connecting a clip lead to the ground frame and connecting the other end of the lead through a 10k 2W resistor to the anode button. (9) When service is required, observe the original lead dress. Extra precaution should be given to assure correct lead dress in the high voltage circuit area. Where a short circuit has occurred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.

0.15 F AC-TYPE PLACE THIS PROBE ON EACH EXPOSED METAL PART

1500 GOOD EARTH GROUND

10W

(11) High voltage hold down circuit check. After repair of the high voltage hold down circuit, this circuit shall be checked to operate correctly.See item "How to check the high voltage hold down circuit".
This mark shows a fast operating fuse, the letters indicated below show the rating. POWER CORD REPLACEMENT WARNING.
Connecting the white line side of power cord to "WHT" character side. PWB White line side

A

V
WHT

PW

(No.YA094)1-3

SECTION 2 SPECIFIC SERVICE INSTRUCTIONS
2.1 FEATURES V-CHIP Since the V-CHIP is built in, it can choose, view and listen to a healthy program. MTS STEREO The voice multiplex function of the MTS system is built in. (MTS = Multi channel Television Sound system) NATURAL CINEMA Watching the movie or animation, press the Natural Cinema to adjust the out line of the images to make thin more sharp. BBE High definition audio adds natural, clear and extraordinary sound quality to any program. VIDEO INPUT LABEL [AV-30W575] This function is used to label video input connections for the onscreen displays. A.H.S. Adds a more spacious surround sound. Music gives basic effect and Movie for more effect. D.I.S.T. (Digital Image Scaling Technology) This system uses line interpolation to double the number of scanning lines and achieve high resolution, flicker-free picture. SMART CAPTION [AV-30W585] Smart caption will appear when you press the MUTING button, only on channels where the broadcast contains CLOSED CAPTION information. SMART SOUND Decreases high sound levels, giving a regulated sound level. FLAT SQUARE CRT It became legible from any position by CRT with few reflection and reflect lumps on the flat screen. DIGITAL COMB FILTER By the 3D digital comb filter, the refreshed image can be seen. VIDEO STATUS Expression of a favorite screen can be chosen by the VIDEO STATUS function. [STANDARD DYNAMIC THEATER GAME] DIGITAL INPUT Digital-in will display when any picture signal (480i/ 480p, 720p/ 1080i) in Digital-in is displayed.

2.2

MAIN DIFFERENCE LIST AV-30W575 SILVER / M.BLACK NO YES YES NO AV-30W585 BLACK YES NO NO YES

Item FRONT CABINET COLOR SMART CAPTION CHANNEL LABEL VIDEO INPUT LABEL AV COMPULINK lll

1-4 (No.YA094)

2.3

TECHNICAL INFORMATION
Pin name BS_RXD /MICON_V LB_PRO NC /RST FORMAT_EDGE /TEST OSD_YS SDA4 SYNCSEL A_MU /MICON_H M_MU OSDXI OSDXO SDA2 AC_IN SCL2 TU_POW VCOI PDO /IP_RESET OSD_YM OSD_B POWER_LED OSD_G OSD_R VREF IP_ERR IREF COMP AVDD CLL VREFLS SUB_CCD NC VSS MAIN_CCD VREFHS CLH VDD/VPP SCL4 I/O I I I I I Not used V. sync for OSD Low B protect detection [Detect: H] Not used CPU reset [Reset: L] Interrupt detection Ys (blanking) for OSD Function Pin No. 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 P74 ON_TIM SBO0 SBD0 SBT1 TS_PC_DET SRQ BS1.5CTL EE_ABL ABL/ACL CHROMA DC_COTL FMT1 FMT2 NC /LOB_POW COMPLINK /POWERGOOD /MECA_ON /MAIN_POW NC /B1_POW C/N X_RAY_M EE_CDS KEY2 KEY1 SCL1 SDA1 REMO POW_DET VSS OSC2 OSC1 VDD SCL0 VOUTENB SDA0 P57 BS_TXD BS_TXD P_MUTE Pin name I/O I I I I I Not used Not used Not used Not used Use for on board writing [for factory] Not used Not used Not used Not used ABL/ACL control Not used Black level DC reproduce control Not used Not used Not used Function

2.3.1 MAIN MICRO COMPUTER (CPU) FUNCTION
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

O Operation test for CPU I/O Data for Inter IC control (for DIST) O Not used O Audio muting [Muting: H] O H. sync for OSD O NC O Keep for OSD oscillation O Keep for OSD oscillation I/O Data for Inter IC control (for MTS) I I I I I AC(60Hz) for timer clock Not used LPF LPF Reset for DIST [Reset: L] YM (transparence) for OSD O Clock for Inter IC control (for MTS)

O Low B power control [Power on: L] I/O AV compulink lll control I I I I Power condition check Main power control [Power on: L] Not used AFT voltage X-ray protect detection [Protect: 0.7V] Not used O Power SW interrupt [Pushing:L]

O B1 power control [Power on: L]

O Blue for OSD O Lighting for POWER LED [Lighting: H] O Green for OSD O Red for OSD I I Reference voltage for OSD AMDP program load error detection [Detect: L ]

I/O Key scan for front key (CH+ Vol-/+) O Key scan for front key (Menu CH-) O Clock for Inter IC control (for Memory) I/O Data for Inter IC control (for Memory) I I I Remote control [No input: H] Not used GND System clock oscillation (4MHz) +3.3V Not used Not used Not used Not used

O Reference current for OSD O Phase adjust for OSD I I I +3.3V Reference voltage in for sub CCD Composite video for sub CCD Not used GND O For low clamp level

O System clock oscillation (4MHz)

O Clock for Inter IC control (for Generally) I/O Data for Inter IC control (for Generally)

O Composite video for main CCD O Reference voltage for main CCD O For high clamp level I +3.3V O Clock for Inter IC control (for DIST)

O Picture muting [Muting: H]

(No.YA094)1-5

SECTION 3 DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE 3.1.9 REMOVING THE DIGITAL INPUT MODULE PWB · Remove the REAR COVER · Remove the AV TERMINAL BOARD. (1) Remove the 1 screw [K] and 1 screw [L]. (2) Remove the DIGITAL INPUT MODULE PWB. NOTE: If necessary, take off the wire clamps, connectors etc. CAUTION AT DISASSEMBLY
AV TERMINAL BOARD DIGITAL INPUT MODULE PWB

3.1.1 REMOVING THE REAR COVER · Unplug the power plug. (1) Remove the 13 screws [A]. (2) Remove the REAR COVER toward you. NOTE: When reinstalling the REAR COVER, carefully push it inward after inserting the chassis into the REAR COVER groove. 3.1.2 REMOVING THE AV TERMINAL BOARD · Remove the REAR COVER. (1) Remove the 5 screws [B] and 1 screw [C]. (2) Withdraw the AV TERMINAL BOARD toward you. 3.1.3 REMOVING THE CHASSIS · Remove the REAR COVER. (1) Slightly raise the both sides of the CHASSIS by hand and remove the 2 claws under the both sides of the CHASSIS from the front cabinet. (2) Withdraw the CHASSIS backward. (If necessary, remove the wire clamps, connectors etc.) 3.1.4 REMOVING THE SPEAKER · Remove the REAR COVER. (1) Remove the 2 screws [C], then remove the SPEAKER toward you. (2) Follow the same steps when removing the other hand SPEAKER. 3.1.5 REMOVING THE FRONT SW PWB · Remove the REAR COVER. Remove the CHASSIS. (1) Remve the 2 screws [D] . (2) Withdrew the FRONT SW PWB. 3.1.6 REMOVING THE SIDE CONTROL PWB AND THE CONTROL BASE · Remove the REAR COVER. (1) Remove the 1 screw [E]. (2) Slightly sift the back and raises the CONTROL BASE. (3) Remove the 2 screws [F]. (4) Remove the SIDE CONTROL PWB from CONTROL BASE. 3.1.7 REMOVING THE LINE FILTER PWB & LINE FILTER COVER · Remove the REAR COVER. (1) Remove the 5 screws [G]. (2) Remove the LINE FILTER PWB from the LINE FILTER COVER. (3) Remove the 2 screws [H]. (4) Remove the LINE FILTER COVER. 3.1.8 REMOVING THE MI-COM & DIST MODULE PWB · Remove the REAR COVER. (1) Remove the 2 screws [J]. (2) Lift the MI-COM & DIST MODULE PWB and remove it.

1 3 5

2 4 6

SB connector

· Prior to disassembly, unplug the power plug from the AC outlet without fail. (Turn the power "off".) · Short the SB connector [1] pin and [2] pin of the DIGITAL INPUT MODULE PWB. (At the time of assembling) · Before the rear cover is inserted into the cabinet, release the short-circuit between the SB connector [1] pin and [2] pin of the DIGITAL INPUT MODULE PWB. · After releasing the short-circuit between the SB connectors, do not turn the power on until the rear cover is inserted into the cabinet. · Negligence in carrying out the above steps may cause the inactivation of the TV. 3.1.10 CHECKING THE PW BOARD · To check the PW Board from backsid. (1) Pull out the CHASSIS. (Refer to REMOVING THE CHASSIS). (2) Erect the CHASSIS vertically with the FRONT side facing up so that you can easily check the back side of the PW Board. CAUTION: · When erecting the CHASSIS, be careful so that there will be no contact with other PWB. · Before turning the power on, make sure that the CRT earth wire and other connectors are properly connected. 3.1.11 WIRE CLAMPING AND CABLE TYING (1) Be sure to clamp the wire. (2) Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.

1-6 (No.YA094)

PICTURE TUBE

CRT SOCKET PWB SPEAKER

C
FRONT CONTROL PWB

J
MI-COM & DIST MODULE PWB

SIDE CONTROL PWB

DEF OSC PWB DEF & POWER PWB DIGITAL INPUT K CLAW MODULE PWB

F H
CONTROL BASE

D SHACCIS
BASE

E G

CLAW MAIN PWB RECEIVER PWB LINE FILTER PWB

TERMINAL BOARD

21 B

L

SPEAKER

C

POWER CORD REAR COVER

A

Fig.1

(No.YA094)1-7

3.1.12 REMOVING THE CRT NOTE: · Replacement of the CRT should be performed by 2 or more persons. · After removing the REAR COVER, CHASSIS etc., (1) Putting the CRT change table on soft cloth, the CRT change table should also be covered with such soft cloth (shown in Fig. 2). (2) While keeping the surface of CRT down, mount the TV set on the CRT change table balanced will as shown in Fig. 2. (3) Remove 4 screws marked by arrows with a box type screwdriver as shown in Fig. 3. NOTE: Since the cabinet will drop when screws have been removed, be sure to support the cabinet with hands. (4) After 4 screws have been removed, put the cabinet slowly on cloth (At this time, be carefully so as not to damage the front surface of the cabinet) shown in Fig. 4. NOTE: · The CRT should be assembled according to the opposite sequence of its dismounting steps. · The CRT change table should preferably be smaller that the CRT surface, and its height be about 35cm.
CRT CHANGE TABLE

APPROX. 35cm CLOTH

Fig.2
CRT

CRT CHANGE TABLE BOX TYPE SCREW DRIVER

Fig.3
CRT

CABINET

CRT CHANGE TABLE

Fig.4 COATING OF SILICON GREASE FOR ELECTRICAL INSULATION ON THE CRT ANODE CAP SECTION. Subsequent to replacement of the CRT and HV transformer or repair of the anode cap, etc. by dismounting them, be sure to coat silicon grease for electrical insulation as shown in Fig.5.Wipe around the anode button with clean and dry cloth. (Fig.5)Coat silicon grease on the section around the anode button. At this time, take care so that any silicon greases dose not sticks to the anode button. (Fig.6) Silicon grease product No. KS-650N
CRT Anode button
Approx. 20mm (Do not coat grease on this section Silicon grease should be coated by 5mm or more from the outside diameter of anode cap.

Silicon grease coating

Anode button (No sticking of silicon grease)

Coating position of silicon grease Anode cap

Fig.5

Fig.6

1-8 (No.YA094)

3.2

MEMORY IC REPLACEMENT

· This model uses the memory IC. · This memory IC stores data for proper operation of the video and drive circuits. · When replacing, be sure to use an IC containing this (initial value) data.

3.2.1 MEMORY IC REPLACEMENT PROCEDURE 1. POWER OFF Switch off the power and disconnect the power plug.

3.2.2 SERVICE ADJUSTMENT ITEM

SERVICE MODE MAIN MENU

2. REPLACE THE MEMORY IC Be sure to use the memory IC written with the initial setting values.

3. POWER ON Connect the power plug to the AC outlet and switch on the power.

1.PICTURE/SOUND 2.YC SEP 3.WHITE BALANCE 4.MEMORY SETUP 5.RF AFC 6.

7. 8.IP 9.DSD 0.HDMI

4. RECEIVING CHANNEL SETTING Refer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.

Setting items Audio circuits (A)

Settings Adjust Adjust Adjust Fixed Fixed

Item No. A01 to A27 S01 to S99 D01 to D32 F01 to F70 YCM001 to YCM185 YCS001 to YCS018 BR DRV R DRV B CUT R CUT G CUT B

1.PICTURE/SOUND (Video / Audio setting) Video circuits (S) Deflection circuits (D) Factory setting items (F)

5. USER SETTING Check the user setting items according to the given in page later. Where these do not agree, refer to the OPERATING INSTRUCTIONS and set the items as described.

2.YC SEP (3D YC separation setting) [Do not adjust] Fixed

6. SERVICE MODE SETTING Verify what to set in the SERVICE MODE, and set whatever is necessary. Refer to the INITIAL SETTING VALUE OF SERVICE MODE.

3.WHITE BALANCE (White balance adjustment)

Adjust

4.MEMORY SETUP (Memory data edit) [Do not adjust] 5.RF AFC (AFC setting) [Do not adjust] Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed --IPA001 to IPA042 DSA001 to DSA053 DSB001 to DSB053 DSC001 to DSC044 DSD001 to DSD017 HDM001 to HDM080 RHD001 to RHD170 8.IP (DIST processing setting) [Do not adjust] 9.DSD (Digital super detail setting) [Do not adjust]

0.HDMI (Digital input processing setting) [Do not adjust]

(No.YA094)1-9

3.2.3 SETTINGS OF FACTORY SHIPMENT 3.2.3.1 POWER CHANNEL VOLUME 3.2.3.2 INPUT CHANNEL VOLUME (Normal) MUTING DISPLAY ASPECT SLEEP TIMER THEATER PRO VIDEO STATUS C. C. SOUND A.H.S BBE SMART SOUND BUTTON OPERATION Setting item Off CABLE-02 10 BASS TREBLE BALANCE MTS 2. CLOCK / TIMERS Setting item SET CLOCK ON / OFF TIMER 3. INITIAL SETUP Setting item DIGITAL-IN DIGITAL-AUDIO CENTER CH INPUT AUDIO OUT TV SPEAKER NOISE MUTING FRONT PANEL LOCK V1 SMART INPUT VIDEO INPUT LABEL LANGUAGE CLOSED CAPTION AUTO SHUT OFF TILT CORRECTION V-CHIP XDS ID AUTO DEMO SIZE 1 DIGITAL OFF FIX ON ON OFF OFF All blank [AV-30W575] ENG. OFF (CC1,T1) OFF Center OFF ON OFF Setting position OFF OFF Setting position Setting position 3.2.3.3 REMOTE CONTROL MENU OPERATION Setting item 00 00 00 STEREO Setting position 1. SOUND ADJUST

REMOTE CONTROL DIRECT OPERATION Setting item TV CABLE-02 10 OFF OFF REGULAR OFF OFF DYNAMIC OFF OFF ON OFF Setting position

VOLUME (Center CH in mode) 10

MULTI SCREEN SELECT (TWIN) CABLE-02 (LEFT SIDE) VIDEO 1 (RIGHT SIDE)

4. PICTURE ADJUST Customers can adjust the picture setting of menu screen as their own like but the picture standard value during factory shipment is as below. < NTSC MODE > Setting item STANDARD DINAMIC THEATER GAME < HD MODE > Setting item STANDARD DINAMIC THEATER GAME TINT 00 00 00 00 COLOR 00 00 00 00 PICTURE 00 +30 00 -10 BRIGHT 00 00 00 00 DETAIL 00 00 00 00 COLOR DIG. NOISE TEMPERATURE CLEAR LOW OFF HIGH OFF LOW OFF HIGH OFF VSM ON ON ON ON TINT 00 00 00 00 COLOR 00 00 00 00 PICTURE 00 +30 00 -10 BRIGHT 00 00 00 00 DETAIL 00 +03 00 0 COLOR DIG. NOISE TEMPERATURE CLEAR LOW OFF HIGH OFF HIGH OFF HIGH OFF VSM ON ON ON ON

1-10 (No.YA094)

3.3

REPLACEMENT OF CHIP COMPONENT

3.3.1 CAUTIONS (1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it. 3.3.2 SOLDERING IRON (1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts. 3.3.3 REPLACEMENT STEPS 1. How to remove Chip parts [Resistors, capacitors, etc.] (1) As shown in the figure, push the part with tweezers and alternately melt the solder at each end.

2. How to install Chip parts [Resistors, capacitors, etc.] (1) Apply solder to the pattern as indicated in the figure.

(2) Shift with the tweezers and remove the chip part.

(2) Grasp the chip part with tweezers and place it on the solder. Then heat and melt the solder at both ends of the chip part.

[Transistors, diodes, variable resistors, etc.] (1) Apply extra solder to each lead.
SOLDER SOLDER

[Transistors, diodes, variable resistors, etc.] (1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the solder. (3) First solder lead A as indicated in the figure.

(2) As shown in the figure, push the part with tweezers and alternately melt the solder at each lead. Shift and remove the chip part.

A B C

(4) Then solder leads B and C.
A

NOTE : After removing the part, remove remaining solder from the pattern.

B C

(No.YA094)1-11

SECTION 4 ADJUSTMENT
4.1 ADJUSTMENT PREPARATION 4.3 MEASURING INSTRUMENT AND FIXTURES (1) There are 2 ways of adjusting this TV : One is with the REMOTE CONTROL UNIT and the other is the conventional method using adjustment parts and components. (2) The adjustment using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values. (3) Make sure that connection is correctly made AC to AC power source. (4) Turn on the power of the TV and measuring instruments for warning up for at least 30 minutes before starting adjustments. (5) If the receive or input signal is not specified, use the most appropriate signal for adjustment. (6) Never touch the parts (such as variable resistors, transformers and condensers) not shown in the adjustment items of this service adjustment. 4.2 PRESET SETTING BEFORE ADJUSTMENTS · DC voltmeter (or digital voltmeter) · Oscilloscope · Signal generator (Pattern generator) [NTSC (480i) / 480p / 720p / 1080i / DIGITAL] · TV audio multiplex signal generator · Remote control unit

4.4

ADJUSTMENT ITEMS

CHECK ITEM · B1 VOLTAGE check · HIGH VOLTAGE HOLD DOWN CIRCUIT check FOCUS · FOCUS adjustment HORIZONTAL FREQUENCY · H. FREQUENCY adjustment DEFLECTION CIRCUIT · V. POSITION / V. SIZE / V. LINEARITY adjustment · H. POSITION / H. SIZE / SIDE PIN / TRAPEZIUM adjustment VIDEO CIRCUIT · WHITE BALANCE(High Light & Low Light) adjustment · SUB BRIGHT adjustment · SUB CONTRAST adjustment · SUB COLOR / SUB TINT / B-Y GAIN (1) adjustment · SUB COLOR / SUB TINT / B-Y GAIN (2) adjustment MTS CIRCUIT · MTS INPUT LEVEL adjustment · MTS SEPARATION adjustment

Unless otherwise specified in the adjustment items, preset the following functions with the REMOTE CONTROL UNIT. Item VIDEO STATUS TINT, COLOR, PICTURE, BRIGHT, DETAIL COLOR TEMPERATURE DIG. NOISE CLEAR NATURAL CINEMA BASS, TREBLE, BALANCE A.H.S BBE AUDIO OUT ASPECT Preset value STANDARD Center (00) LOW OFF AUTO Center (00) OFF ON FIX FULL

1-12 (No.YA094)

4.5

ADJUSTMENT LOCATIONS
FRONT

POWER SW

R

CN100Y

TOP

K Y

CRT

CN100K

G

H

FRONT CONTROL PWB

SIDE CONTROL PWB
FRONT
SPEAKER L/R

MAIN PWB
F G M CN1001 CN2001 H B

RECEIVER PWB

CN1004
CN1002 CN2002

F

B CN1006

FRONT

MAIN MI-CON (CPU)

J

CRT SOCKET PWB

LINE FILTER PWB
F9901 (7A)

CN1008

TOP

MEMORY IC
CN2008 CN1003 CN2003

CN1009
IC1703

CN1005

PW

DC

SR

CN000E

DEF OSC PWB DEF & POWER PWB
A Q

POWER CORD

U/V TUNER TU1101

MI-COM & DIST MODULE PWB

AU

J2101

J2111

J2121

DIGITAL INPUT MODULE PWB

(No.YA094)1-13

TOP FRONT

DIGITAL INPUT MODULE PWB
TOP
AU

CRT SOCKET PWB (solder side)
TP-B TP-R VM

VM.COIL
DC SB
1 3 5 2 4 6

CRT SOCKET E

Q

SR TP-G A E2 TP-E1 J

MAIN PWB FRONT CONTROL PWB

MI-COM & DIST MODULE PWB

CRT EARTH

LINE FILTER PWB

DEF & POWER PWB
B DEG

H

FRONT

CN2001

DEG.COIL
CN2002

J

MAIN PWB

CN2010 CN2003

DEF.YOKE

HV

CRT ANODE

DEF OSC PWB
FBT
S1 1Pin 2Pin 3Pin 4Pin 5Pin 5 S1 1 : : : : : TP-E ( ) X-ray2 X-ray1 NC TP-91B (B1)

A

Q
AU

UPPER : FOCUS VR (H) CENTER : FOCUS VR (V) LOWER : SCREEN VR

1-14 (No.YA094)

4.6

BASIC OPERATION OF SERVICE MODE
SERVICE MENU

1.PICTURE/SOUND 2.YC SEP 3.WHITE BALANCE 4.MEMORY SETUP 5.RF AFC

8.IP 9.DSD 0.HDMI

1.PICTURE/SOUND

5.RF AFC

DO NOT ADJUST

NTSC FULL ST L FL MUTE

TOO HIGH GOOD TOO LOW TUNER AFC FINE MAIN ON +28

A01

IN LEVEL

008

A01~A27
A01 IN LEVEL 008

S01~S99
S01 COLOR 099

D01~D32
D01 V.SIZE 049

F01~F70
F01 001

DO NOT ADJUST

2.YC SEP
NTSC FULL ST L FL MUTE

8.IP
NTSC FULL ST L FL MUTE

DO NOT ADJUST

YCM001~YCM185 YCS001~YCS018
YCM001 000 002 IPA001 0C7

IPA001~IPA042

3.WHITE BALANCE

9.DSD

DO NOT ADJUST

NTSC FULL ST L FL MUTE

BR 118 DRV R 089 B 108 CUT R 247 G 244 B 226

DSA001~DSA053 DSB001~DSB053 DSC001~DSC044 DSD001~DSD017
DSA001 0CF 002

DO NOT ADJUST

4.MEMORY SETUP
ADDR 0 1 AA 55 8 9 00 00 0000 2 3 4 5 6 7 00 00 FF 00 00 00 A B C D E F 00 00 00 00 00 00

0.HDMI

DO NOT ADJUST

NTSC FULL ST L FL MUTE

HDM001~HDM080 RHD001~RHD170
HDM001 000

(No.YA094)1-15

4.6.1 TOOL OF SERVICE MODE OPERATION Operate the SERVICE MODE with the REMOTE CONTROL UNIT. 4.6.2 SERVICE MODE ITEMS In general, basic setting (adjustments) items or verifications are performed in the SERVICE MODE. 1.PICTURE/SOUND 2.YC SEP 3.WHITE BALANCE 4.MEMORY SETUP 5.RF AFC 8.IP 9.DSD 0.HDMI This sets the setting values of the Video / Audio / Defrection circuits. This is used when the YC separation circuit is adjusted. [Do not adjust] This sets the setting values of the WHITE BALANCE. This sets the setting values of the MEMORY ADDRESS. [Do not adjust] This is used when the IF VCO is adjusted. [Do not adjust] This sets the setting value of the DIST circuit. [Do not adjust] This sets the setting value of the DSD (Digital super detail) circuit. [Do not adjust] This sets the setting value of the Digital input circuit. [Do not adjust].

4.6.3 HOW TO ENTER THE SERVICE MODE (1) Set the SLLEP TIMER to 0 minutes using the [SLEEP TIMER] key. (2) Press the [VIDEO STATUS] key and [DISPLAY] key simultaneously, then enter the SERVICE MODE. (3) When the main menu is displayed, press any key of the [0] to [9] key to enter the corresponding sub menu mode. NOTE: Before entering the SERVICE MODE, confirm that the setting of TV / CATV switch of the REMOTE CONTROL UNIT is at the "TV" side and the setting of VCR / DVD switch is at the "VCR" side. If the switches have not been properly set, you cannot enter the SERVICE MODE. 4.6.4 HOW TO STORE OF SETTING VALUE When adjustment is completed, press the [MUTING] key to memorize the adjustment value. If not to do it, adjustment data is not memorized to the memory IC. And if exit the adjustment mode before memorize the data, the adjustment value which you change is canceled. 4.6.5 HOW TO EXIT THE SERVICE MODE Press the [BACK] key to exit the SERVICE MODE.

SERVICE MODE SELECT KEY
VCR/DVD switch TV/CATV switch DISPLAY SLEEP TIMER VIDEO STATUS POWER

NUMBER

CH +

VOL + VOL MENU BACK CH -

RM-C1257G

1-16 (No.YA094)

4.6.6 DESCRIPTION OF STATUS DISPLAY The status display on the upper part of the SERVICE MODE screen is common (to all models).

4.6.7 SERVICE MODE SETTING 1. PICTURE / SOUND Audio, video and defrection circuit adjustment. · Press [SLEEP TIMER] key For skip the adjustment item.
A01 S01 D01 F01

INPUT SIGNAL ASPECT/ MULTI VIDEO STATUS ITEM No.

NTSC CINE ST L FL MUTE

MEMORY MODE IP CHANGIN MODE
A01 IN LEVEL 001

WHITE BALANCE

Skip change

· Press [CH+] / [CH-] key For scrolling up/down the adjustment item.
A01 S01 D01 F01

(1) INPUT SIGNAL NTSC DVD ED HD 750p HDVD HED1 HED2 HHD H750 : Composite, S-video (Y / C), RF, No signal. : 480i (component) : 480p : 1080i : 720p : DIGITAL 480i : DIGITAL 480p SIZE1 : DIGITAL 480p SIZE2 : DIGITAL 1080i : DIGITAL 720p

Item No. is up/down

· Press [VOL+] / [VOL-] key For scrolling up/down the data values. · Press [MUTING] key For memorize the data values. 3. WHITE BALANCE White balance data adjustment.
3. WHITE BALANCE
SETTING VALUE

(2) ASPECT / MULTI 1) ONE SCREEN FULL PANO CINE REGU M1 M2-1 M2-2 M12 : FULL : PANORAMA : CINEMA : REGULAR : SINGLE (for adjustment) : TWIN (4 : 3) : TWIN (16 : 9) : INDEX

R.DRIVE VALUE B.DRIVE VALUE
BRIGHTNESS DRIVE CUTOFF
BR DRV CUT R R G B B

2) MULTI SCREEN

B.CUTOFF VALUE G.CUTOFF VALUE R.CUTOFF VALUE

(3) VIDEO STATUS ST DA TH GA : STANDARD : DYNAMIC : THEATER : GAME

DRIVE [2] key [5] key [3] key [6] key CUTOFF [7] key [TUNE] key [8] key [0] key [9] key [RETURN+] key

: DRIVE R is up : DRIVE R is down : DRIVE B is up : DRIVE B is down

(4) WHITE BALANCE H L FL LI 23 MUTE DIR : HIGH : LOW : FRAME : LINE : COMPULSORY NATURAL CINEMA IN : Press [MUTING] key : Store the data to the memory at the same time.

(5) IP CHANGING MODE

: CUTOFF G is up : CUTOFF G is down : CUTOFF R is up : CUTOFF R is down : CUTOFF B is up : CUTOFF B is down

(6) MEMORY MODE

(No.YA094)1-17

4.7

INITIAL SETTING VALUE OF SERVICE MODE

(1) Adjustment of the SERVICE MODE is made on the basis of the initial setting values. however, the new setting values which displays on the screen in its optimum condition may differ from the initial setting value. (2) Do not change the initial setting values of the items not listed in "ADJUSTMENT PROCEDURE". (3) "---" is impossible to adjust. (4) When the FULL mode has been established, the setting of other modes will be done automatically. However, if the picture quality has not been optimized, adjust each mode again, respectively. 4.7.1 [1.PICTURE/SOUND] Item No. Item Variable range 000 to 015 000 to 063 000 to 015 -128 to +127 -128 to +127 000 to 001 -128 to +127 -128 to +127 -128 to +127 -128 to +127 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 Setting value 008 035 020 +009 +006 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 Item No. D02 EW D03 H.SIZE D04 V.SCORE D05 V.LINE D06 V.CENT D07 EW.TRAP D08 BOT.CORN D09 TOP.CORN D10 V EHT D11 H EHT D12 D13 (Not display) (Not display) Item Variable range 000 to 127 000 to 063 000 to 063 000 to 063 000 to 063 000 to 063 000 to 063 000 to 015 000 to 015 000 to 007 000 to 007 000 to 007 000 to 015 000 to 255 000 to 255 000 to 127 000 to 003 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 Setting value 094 010 047 014 038 037 032 009 009 003 001 005 000 158 182 111 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000

A01 IN LEVEL A02 LOW SEP A03 HI SEP A04 BBE BASS A05 BBE TRE A06 SURROUND A07 BASS OFS A08 TRE OFS A09 AHS MVE A10 AHS MSC A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

D01 V.SIZE

D14 H.CENTER D15 H.FREQ D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 D32 (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

1-18 (No.YA094)

Item No.

Item

Variable range 000 to 255 000 to 255

Setting value NTSC 076 068 088 071 073 065 480i 076 074 083 063 480p 079 077 720p / 1080i 067 080 070 070 STANDARD THEATER STANDARD THEATER STANDARD THEATER STANDARD THEATER

S01 COLOR S02 TINT

Item No.

Item

Variable range 000 to 255 000 to 127 Variable range 000 to 003 000 to 003 000 to 063 000 to 015 000 to 003

Setting value NTSC STANDARD 127 077 THEATER 127 041 127 071 480i / 480p STANDARD THEATER 127 040 720p/ 1080i STANDARD 127 083 THEATER 127 043

S03 BRIGHT S04 CONTRAST Item No.

Setting value NTSC 000 001 016 007 002 000 001 019 000 003 000 001 014 007 001 480i 000 001 020 002 003 000 001 011 007 001 480p 000 001 016 002 003 720p / 1080i 000 000 012 007 002 000 000 020 003 002 STANDARD THEATER STANDARD THEATER STANDARD THEATER STANDARD THEATER

Item

S05 O MTX SW S06 INPUT SW S07 B-Y S08 R-Y S09 G-YMATRI

Setting value Item No. Item Variable range 000 to 255 -128 to 127 000 to 255 -128 to 127 NTSC STANDARD HIGH S10 DRIVE R S11 (Not display) S12 DRIVE B S13 (Not display) --+006 --+004 LOW 145 --124 --THEATER HIGH --+013 ---004 LOW --+020 ---016 STANDARD HIGH --+012 --+009 LOW 146 --127 --480i THEATER HIGH --+012 ---015 LOW --+016 ---028

Setting value Item No. Item Variable range 000 to 255 -128 to +127 000 to 255 -128 to +127 480p STANDARD HIGH S10 DRIVE R S11 (Not display) S12 DRIVE B S13 (Not display) ---004 ---002 LOW --+003 ---005 THEATER HIGH --+011 ---015 LOW --+014 ---028 HIGH --+006 --+006 720p / 1080i STANDARD LOW 142 --123 --THEATER HIGH --+012 ---012 LOW --+016 ---026

Item No.

Item

Variable range 000 to 255 -128 to +127 000 to 255 -128 to +127 000 to 255 -128 to +127 000 to 003

Setting value NTSC STANDARD 227 --227 --227 --001 THEATER ---002 --+003 --+003 --480i / 480p STANDARD 227 --227 --227 --001 THEATER ---004 --000 --+003 --720p / 1080i STANDARD 227 --227 --227 --001 THEATER ---006 ---005 --+004 --(No.YA094)1-19

S14 CUTOFF R S15 (Not display) S16 CUTOFF G S17 (Not display) S18 CUTOFF B S19 (Not display) S20 CUTOFSWR

Item No.

Item

Variable range 000 to 003 000 to 003

Setting value NTSC STANDARD 001 001 THEATER ----001 001 480i / 480p STANDARD THEATER ----720p / 1080i STANDARD 001 001 THEATER -----

S21 CUTOFSWG S22 CUTOFSWB

Item No.

Item

Variable range 000 to 255 Variable range 000 to 015 Variable range 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015

Setting value NTSC STANDARD 255 THEATER 000 000 480i / 480p STANDARD THEATER 000 720p / 1080i STANDARD 255 THEATER 000

S23 DC CTL Item No. Item

Setting value 000 Setting value NTSC 005 008 007 015 002 004 480i 010 006 006 015 000 004 Setting value NTSC STANDARD ----THEATER --------Setting value 480i --------480p ----720p / 1080i --------STANDARD THEATER STANDARD THEATER STANDARD THEATER OTHERS 010 009 007 015 001 004

S24 RGBLIMIT Item No. Item

S25 BL STRT S26 BL GAIN S27 YGM LVL S28 YGM GAIN S29 YWD STRT S30 YWD GAIN

Item No.

Item

Variable range 000 to 255 000 to 255

S31 COL OFST S32 TNT OFST

Item No.

Item

Variable range -128 to +127 -128 to +127 Variable range 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 Variable range 000 to 001 000 to 001 000 to 001 000 to 015

SCREEN MODE (MULTI SCREEN) TWIN / FREEZE STANDARD THEATER 000 000 Setting value STANDARD 000 000 000 000 000 Seeting value 000 000 000 015 THEATER 000 001 001 000 000 000 -019 ----OTHER STANDARD THEATER -----

S33 BRT OFST S34 CNT OFST Item No. Item

S35 DCTRN SW S36 BL OFF S37 YGM OFF S38 ABL OFF S39 ACL OFF Item No. Item

S40 BLCNT LK S41 YGCNT LK S42 DCTRN PL S43 ABL GAIN 1-20 (No.YA094)

Item No.

Item

Variable range 000 to 015 000 to 015 000 to 015 Variable range 000 to 255 Variable range 000 to 255 000 to 127 000 to 127 000 to 001 Variable range -128 to +127 -128 to +127 -128 to +127 Variable range -128 to +127 -128 to +127 000 to 031 000 to 031 000 to 127 000 to 255 000 to 255 -128 to +127 -128 to +127 -128 to +127 -128 to +127 -128 to +127 -128 to +127 -128 to +127 -128 to +127 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001

Seeting value 015 015 000 Setting value STANDARD 255 Setting value 255 064 064 000 Setting value STANDARD -041 +017 -017 Setting value 000 000 008 015 004 093 108 +002 -020 -010 +010 -022 -019 -016 000 000 000 000 000 000 000 000 000 000 000 (No.YA094)1-21 THEATER -027 +017 -017 Item No. S80 S81 S82 S83 S84 S85 S86 S87 S88 S89 S90 S91 S92 S93 S94 S95 S96 S97 S98 S99 Setting item (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) Variable range 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 Setting value 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 DYNAMIC 255 THEATER 255 GAME 255

S44 ABL STRT S45 ACL GAIN S46 ACL STRT Item No. Item

S47 ACL EERG Item No. Setting item

S48 CHRM GM S49 OSDR DC S50 OSDB DC S51 BLK OFF Item No. Item

S52 CNT UNDR S53 CNT UPPR S54 BRT UNDR Item No. Setting item

S55 EETH BRT S56 EETH CNT S57 BREE CNT S58 DKEE CNT S59 DREE BRT S60 BREE ACL S61 DKEE ACL S62 VMOFF DE S63 VM LOW S64 VM MID S65 VM HIGH S66 VM LS67 VM LH S68 VM MH S69 VM M+ S70 S71 S72 S73 S74 S75 S76 S77 S78 S79 (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Item No.

Setting item

Variable range 000 to 255 000 to 255 000 to 255 000 to 001 000 to 255 000 to 255 000 to 255 000 to 255 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 127 000 to 001 000 to 001 000 to 001 000 to 255 000 to 255 000 to 001 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 003 000 to 001 000 to 063 000 to 001 000 to 001

Setting value AV-30W575 AV-30W585 007 003 127 001 242 121 015 000 000 000 000 000 000 000 000 070 000 000 000 005 002 000 000 141 006 040 040 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 039 000 000 006 003 127 001 202 121 015 000 000 000 000 000 000 000 000 070 000 000 000 005 002 000 000 141 006 040 040 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 039 000 000

Item No. F46 F47 F48 F49 F50 F51 F52 F53 F54 F55 F56 F57 F58 F59 F60 F61 F62 F63 F64 F65 F66 F67 F68 F69 F70

Setting item (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 015 000 to 063 -128 to +127 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 000 to 001 000 to 001 000 to 001 000 to 001 -128 to +127 -128 to +127 -128 to +127 000 to 007 000 to 003 000 to 255 000 to 001 000 to 001

Setting value AV-30W575 AV-30W585 000 000 000 001 001 011 062 000 015 000 188 105 077 001 127 001 000 +001 -001 +010 000 002 126 001 000 000 000 000 001 001 011 062 000 015 000 188 105 077 001 127 001 000 +001 -001 +010 000 002 126 001 000

F01 E 1 F02 E 2 F03 F05 F06 F07 F08 (Not display) (Not display) (Not display) (Not display) (Not display) F04 CATVMAX

F09 AUTOSCR 1 F10 AUTOSCR 2 F11 AUTOSCR 3 F12 AUTOSCR 4 F13 AUTOSCR 5 F14 AUTOSCR 6 F15 AUTOSCR 7 F16 F17 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

F18 FIX DATA

F32 ATT V F33 ATT U F34 ATT C F35 F36 F37 (Not display) (Not display) (Not display)

F38 DC1 F39 DC4 F40 DC5 F41 SS LV F42 SS CP F43 SS HDP F44 F45 (Not display) (Not display)

1-22 (No.YA094)

4.7.2 [2.YC SEP] (*All the values are fixed values) NOTE : Initial setting value is reference value at following condition. INPUT SIGNAL ASPECT MULTI-SCREEN VIDEO STATUS COLOR TEMPERATURE Item No. YCM001 YCM002 YCM003 YCM004 YCM005 YCM006 YCM007 YCM008 YCM009 YCM010 YCM011 YCM012 YCM013 YCM014 YCM015 YCM016 YCM017 YCM018 YCM019 YCM020 YCM021 YCM022 YCM023 YCM024 YCM025 YCM026 YCM027 YCM028 YCM029 YCM030 YCM031 YCM032 YCM033 YCM034 YCM035 YCM036 YCM037 YCM038 YCM039 Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) : NTSC : FULL : SINGLE : STANDARD : LOW Variable range 000 to 001 000 to 001 000 to 001 000 to 003 000 to 255 000 to 003 000 to 255 000 to 001 000 to 003 000 to 001 000 to 001 000 to 001 000 to 001 000 to 003 000 to 001 000 to 003 000 to 001 000 to 003 000 to 001 000 to 001 000 to 003 000 to 007 000 to 001 000 to 001 000 to 007 000 to 015 000 to 003 000 to 007 000 to 007 000 to 003 000 to 001 000 to 003 000 to 001 000 to 001 000 to 255 000 to 001 000 to 003 000 to 127 000 to 127 Setting value 000 000 000 001 239 001 239 000 000 000 000 000 000 000 000 001 001 000 000 000 002 004 001 000 005 003 000 003 006 001 000 003 001 000 096 001 001 062 073

Item No. YCM040 YCM041 YCM042 YCM043 YCM044 YCM045 YCM046 YCM047 YCM048 YCM049 YCM050 YCM051 YCM052 YCM053 YCM054 YCM055 YCM056 YCM057 YCM058 YCM059 YCM060 YCM061 YCM062 YCM063 YCM064 YCM065 YCM066 YCM067 YCM068 YCM069 YCM070 YCM071 YCM072 YCM073 YCM074 YCM075 YCM076 YCM077 YCM078 YCM079 YCM080 YCM081 YCM082 YCM083 YCM084

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 003 000 to 063 000 to 001 000 to 001 000 to 255 000 to 001 000 to 255 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 003 000 to 003 000 to 003 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 015 000 to 015 000 to 001 000 to 063 000 to 063 000 to 063 000 to 063 000 to 063 000 to 063 000 to 127 000 to 001 000 to 001 000 to 063 000 to 001 000 to 001 000 to 063 000 to 063 000 to 255 000 to 255 000 to 255 000 to 255 000 to 001 000 to 063

Setting value 002 016 000 000 241 000 165 001 001 001 001 001 000 001 003 003 000 000 001 001 000 001 001 004 000 060 040 025 012 036 031 031 001 001 024 000 001 010 001 000 000 000 000 001 012

(No.YA094)1-23

Item No. YCM085 YCM086 YCM087 YCM088 YCM089 YCM090 YCM091 YCM092 YCM093 YCM094 YCM095 YCM096 YCM097 YCM098 YCM099 YCM100 YCM101 YCM102 YCM103 YCM104 YCM105 YCM106 YCM107 YCM108 YCM109 YCM110 YCM111 YCM112 YCM113 YCM114 YCM115 YCM116 YCM117 YCM118 YCM119 YCM120 YCM121 YCM122 YCM123 YCM124 YCM125 YCM126 YCM127 YCM128 YCM129

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 001 000 to 001 000 to 063 000 to 001 000 to 031 000 to 003 000 to 015 000 to 015 000 to 015 000 to 063 000 to 255 000 to 001 000 to 063 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 015 000 to 255 000 to 255 000 to 255 000 to 255 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 003 000 to 001 000 to 255 000 to 001 000 to 255 000 to 001 000 to 001 000 to 001 000 to 001

Setting value 000 000 028 001 000 000 000 000 002 000 035 001 063 008 005 008 005 000 002 008 006 010 032 031 064 000 001 001 001 000 001 000 000 001 000 000 003 000 026 000 025 000 001 001 001

Item No. YCM130 YCM131 YCM132 YCM133 YCM134 YCM135 YCM136 YCM137 YCM138 YCM139 YCM140 YCM141 YCM142 YCM143 YCM144 YCM145 YCM146 YCM147 YCM148 YCM149 YCM150 YCM151 YCM152 YCM153 YCM154 YCM155 YCM156 YCM157 YCM158 YCM159 YCM160 YCM161 YCM162 YCM163 YCM164 YCM165 YCM166 YCM167 YCM168 YCM169 YCM170 YCM171 YCM172 YCM173 YCM174

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 003 000 to 255 000 to 255 000 to 255 000 to 007 000 to 255 000 to 001 000 to 001 000 to 007 000 to 255 000 to 007 000 to 255 000 to 001 000 to 007 000 to 255 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 001 000 to 255 000 to 001 000 to 001 000 to 001 000 to 003 000 to 015 000 to 015 000 to 001 000 to 127 000 to 001 000 to 031 000 to 001 000 to 015 000 to 007 000 to 031 000 to 255 000 to 003 000 to 063 000 to 015 000 to 015 000 to 007 000 to 255 000 to 007 000 to 255

Setting value 001 050 154 055 001 136 000 001 003 089 000 252 001 005 128 000 001 001 001 000 000 136 001 001 001 000 015 004 001 004 000 000 000 003 002 016 235 000 000 003 003 000 096 003 056

1-24 (No.YA094)

Item No. YCM175 YCM176 YCM177 YCM178 YCM179 YCM180 YCM181 YCM182 YCM183 YCM184 YCM185

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 001 000 to 001 000 to 255 000 to 001 000 to 001 000 to 007 000 to 063 000 to 003 000 to 003 000 to 003 000 to 255

Setting value 000 000 022 001 000 004 001 001 001 001 000

NOTE : Initial setting value is reference value at following condition. INPUT SIGNAL ASPECT MULTI-SCREEN VIDEO STATUS COLOR TEMPERATURE Item No. YCS001 YCS002 YCS003 YCS004 YCS005 YCS006 YCS007 YCS008 YCS009 YCS010 YCS011 YCS012 YCS013 YCS014 YCS015 YCS016 YCS017 YCS018 Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) : RF(RIGHT SCREEN) : FULL : SPLIT : STANDARD : LOW Variable range 000 to 063 000 to 063 000 to 031 000 to 031 000 to 031 000 to 015 000 to 015 000 to 015 000 to 015 000 to 003 000 to 003 000 to 001 000 to 001 000 to 003 000 to 003 000 to 001 000 to 003 000 to 001 Setting value 029 017 004 014 014 007 007 005 008 001 001 001 001 000 001 000 002 001

(No.YA094)1-25

4.7.3 [3.WHITE BALANCE] NOTE : Initial setting value is reference value at following condition. INPUT SIGNAL ASPECT MULTI-SCREEN VIDEO STATUS COLOR TEMPERATURE Item No. BR DRV R DRV B CUT R CUT G CUT B Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) : NTSC : FULL : SINGLE : STANDARD : LOW Variable range 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 Setting value 127 145 124 031 031 031

Item No. IPA025 IPA026 IPA027 IPA028 IPA029 IPA030 IPA031 IPA032 IPA033 IPA034 IPA035 IPA036 IPA037 IPA038 IPA039 IPA040 IPA041 IPA042

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 00F 000 to 0FF 000 to 00F

Setting value 000 019 000 01B 000 01D 000 000 000 010 000 000 00F 010 000 000 011 000

4.7.4 [8.IP] (*All the values are fixed values) NOTE : Initial setting value is reference value at following condition. INPUT SIGNAL ASPECT MULTI-SCREEN VIDEO STATUS COLOR TEMPERATURE Item No. IPA001 IPA002 IPA003 IPA004 IPA005 IPA006 IPA007 IPA008 IPA009 IPA010 IPA011 IPA012 IPA013 IPA014 IPA015 IPA016 IPA017 IPA018 IPA019 IPA020 IPA021 IPA022 IPA023 IPA024 Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) : NTSC : FULL : SINGLE : STANDARD : LOW Variable range 000 to 0FF 000 to 0FF 000 to 0FF 000 to 0FF 000 to 01F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF Setting value 0D0 000 000 05E 001 037 000 000 000 080 002 02B 002 000 002 080 001 000 001 080 000 016 000 017

4.7.5 [9.DSD] (*All the values are fixed values) NOTE : Initial setting value is reference value at following condition. INPUT SIGNAL ASPECT MULTI-SCREEN VIDEO STATUS COLOR TEMPERATURE Item No. DSA001 DSA002 DSA003 DSA004 DSA005 DSA006 DSA007 DSA008 DSA009 DSA010 DSA011 DSA012 DSA013 DSA014 DSA015 DSA016 DSA017 DSA018 Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) : NTSC : FULL : SINGLE : STANDARD : LOW Variable range 000 to 03F 000 to 03F 000 to 03F 000 to 003 000/001 000 to 003 000 to 03F 000/001 000 to 03F 000/001 000/001 000 to 03F 000 to 03F 000 to 03F 000 to 003 000/001 000 to 003 000 to 03F Setting value 014 023 026 000 000 002 00C 001 010 001 001 00A 012 02D 002 001 000 00A

1-26 (No.YA094)

Item No. DSA019 DSA020 DSA021 DSA022 DSA023 DSA024 DSA025 DSA026 DSA027 DSA028 DSA029 DSA030 DSA031 DSA032 DSA033 DSA034 DSA035 DSA036 DSA037 DSA038 DSA039 DSA040 DSA041 DSA042 DSA043 DSA044 DSA045 DSA046 DSA047 DSA048 DSA049 DSA050 DSA051 DSA052 DSA053 Item No. DSB001 DSB002 DSB003 DSB004 DSB005 DSB006 DSB007 DSB008

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000/001 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000/001 000 to 03F 000/001 000 to 003 000 to 03F 000/001 000/001 000 to 03F 000/001 000 to 003 000 to 03F 000/001 000/001 000/001 000 to 03F 000/001 000 to 003 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000/001 Variable range 000 to 03F 000 to 03F 000 to 03F 000 to 003 000 to 003 000 to 003 000 to 03F 000/001

Setting value 001 000 001 018 001 017 001 000 001 00D 001 001 020 000 001 008 001 001 020 000 001 008 001 001 001 01F 000 003 025 001 00C 001 008 001 001 Setting value -----------------

Item No. DSB009 DSB010 DSB011 DSB012 DSB013 DSB014 DSB015 DSB016 DSB017 DSB018 DSB019 DSB020 DSB021 DSB022 DSB023 DSB024 DSB025 DSB026 DSB027 DSB028 DSB029 DSB030 DSB031 DSB032 DSB033 DSB034 DSB035 DSB036 DSB037 DSB038 DSB039 DSB040 DSB041 DSB042 DSB043 DSB044 DSB045 DSB046 DSB047 DSB048 DSB049 DSB050 DSB051 DSB052 DSB053

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 03F 000/001 000/001 000 to 03F 000 to 03F 000 to 03F 000 to 003 000/001 000 to 003 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000/001 000 to 03F 000/001 000 to 003 000 to 03F 000/001 000/001 000 to 03F 000/001 000 to 003 000 to 03F 000/001 000/001 000/001 000 to 03F 000/001 000 to 003 000 to 03F 000/001 000 to 03F 000/001 000 to 03F 000/001 000/001

Setting value -------------------------------------------------------------------------------------------

(No.YA094)1-27

Item No. DSC001 DSC002 DSC003 DSC004 DSC005 DSC006 DSC007 DSC008 DSC009 DSC010 DSC011 DSC012 DSC013 DSC014 DSC015 DSC016 DSC017 DSC018 DSC019 DSC020 DSC021 DSC022 DSC023 DSC024 DSC025 DSC026 DSC027 DSC028 DSC029 DSC030 DSC031 DSC032 DSC033 DSC034 DSC035 DSC036 DSC037 DSC038 DSC039 DSC040 DSC041 DSC042 DSC043 DSC044

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 00F 000 to 0FF 000 to 03F 000 to 003 000 to 0FF 000/001 000/001 000/001 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 0FF 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000 to 00F 000 to 0FF 000/001 000/001

Setting value 008 098 01C 000 000 000 000 000 000 000 00F 0FF 002 00F 004 0DB 000 000 00F 0FF 002 00F 004 0DB 000 080 000 040 005 040 000 0C0 000 080 000 040 005 040 000 0C0 004 07B 000 000

Item No. DSD001 DSD002 DSD003 DSD004 DSD005 DSD006 DSD007 DSD008 DSD009 DSD010 DSD011 DSD012 DSD013 DSD014 DSD015 DSD016 DSD017

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 000 to 255 -128 to +127 -128 to +127 -128 to +127 -128 to +127 -128 to +127 -128 to +127 0001 to 0FF1 0001 to 0FF1 0001 to 0FF1

Setting value 001 002 001 002 001 002 001 002 +001 000 +002 +002 -001 +005 05C1 08B1 0E21

4.7.6 [0.HDMI] (*All the values are fixed values) NOTE : Initial setting value is reference value at following condition. INPUT SIGNAL ASPECT MULTI-SCREEN VIDEO STATUS COLOR TEMPERATURE Item No. HDM001 HDM002 HDM003 HDM004 HDM005 HDM006 HDM007 HDM008 HDM009 HDM010 HDM011 HDM012 HDM013 HDM014 HDM015 HDM016 HDM017 HDM018 HDM019 Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) : 480p(HDMI, SIZE 1) : FULL : SINGLE : STANDARD : LOW Variable range 000/001 000/001 000/001 000/001 000/001 000 to 003 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000 to 255 000 to 255 000 to 255 000/001 Setting value 000 000 000 000 001 000 000 000 000 000 000 000 000 000 000 000 000 000 001

1-28 (No.YA094)

Item No. HDM020 HDM021 HDM022 HDM023 HDM024 HDM025 HDM026 HDM027 HDM028 HDM029 HDM030 HDM031 HDM032 HDM033 HDM034 HDM035 HDM036 HDM037 HDM038 HDM039 HDM040 HDM041 HDM042 HDM043 HDM044 HDM045 HDM046 HDM047 HDM048 HDM049 HDM050 HDM051 HDM052 HDM053 HDM054 HDM055 HDM056 HDM057 HDM058 HDM059 HDM060 HDM061 HDM062 HDM063 HDM064

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000 to 255 000 to 007 000 to 063 000 to 063 000 to 063 000 to 001 000 to 003 000 to 255 000 to 003 000 to 255 000 to 003 000 to 255 000 to 003 000 to 255 000 to 003 000 to 255 000 to 255 000 to 255 000 to 255 000/001 000/001 000/001 000 to 255 000 to 007 000 to 003 000 to 003 000/001 000 to 015 000 to 255 000 to 255 000 to 015 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001

Setting value 000 000 006 006 006 000 002 180 000 192 000 212 000 224 001 012 026 001 012 000 000 000 001 003 000 000 001 007 000 000 000 000 000 000 000 000 000 001 000 001 000 001 001 000 000

Item No. HDM065 HDM066 HDM067 HDM068 HDM069 HDM070 HDM071 HDM072 HDM073 HDM074 HDM075 HDM076 HDM077 HDM078 HDM079 HDM080 Item No. RHD001 RHD002 RHD003 RHD004 RHD005 RHD006 RHD007 RHD008 RHD009 RHD010 RHD011 RHD012 RHD013 RHD014 RHD015 RHD016 RHD017 RHD018 RHD019 RHD020 RHD021 RHD022 RHD023 RHD024 RHD025 RHD026 RHD027

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display)

Variable range 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 000/001 Variable range -------------------------------------------------------

Setting value 001 000 001 004 000 001 000 000 000 008 001 001 001 001 001 001 Setting value 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000

(No.YA094)1-29

Item No. RHD028 RHD029 RHD030 RHD031 RHD032 RHD033 RHD034 RHD035 RHD036 RHD037 RHD038 RHD039 RHD040 RHD041 RHD042 RHD043 RHD044 RHD045 RHD046 RHD047 RHD048 RHD049 RHD050 RHD051 RHD052 RHD053 RHD054 RHD055 RHD056 RHD057 RHD058 RHD059 RHD060 RHD061 RHD062 RHD063 RHD064 RHD065 RHD066 RHD067 RHD068 RHD069 RHD070 RHD071 RHD072

Item name (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not display) (Not di