Text preview for : SANYO CE29KF8R FC3-G2.pdf part of SANYO CE29KF8R service manual
Back to : SANYO CE29KF8R FC3-G2.rar | Home
FILE NO.
SERVICE MANUAL Colour Television
Model No. CE29KF8R
(Russia)
Service Ref. No. CE29KF8R-50
TV/AV TIMER P P
MENU
-/--
CH
CH
CH SCAN
TV/AV MENU
-
+
CH
A ·B BASS
SWAP
SOUND
PICTURE SURROUND C.SYS
S.SYS
JXMRM
Specifications
Power Source . . . . . . . . . . AC110-240V, 50Hz/60Hz. Colour System . . . . . . . . . PAL/SECAM/NTSC4.43/NTSC/PAL-60Hz Television System . . . . . . B/G, I, D/KK', MM Channel Coverage . . . . . VHF: E2 - E12,R1 - R12,K1 - K9,J1 - J12,A2 - A13 UHF: 21 - 69, A14 - A69, J13 - J62 CATV: S1-S41, X, Y, Z, Z+1, Z+2 Video IF . . . . . . . . . . . . . . 38.0MHz Aerial Input Impedance . . 75 Ext. Terminals Video inputs: Phono jack x 2 (1Vp - p, 75) S-Video inputs: Din 4 pin x 1 (Separate Y/C signal input) Audio inputs: Phono jack (L/R) x 2 (436mVrms, more than 40K) Video monitor outputs: Phono jack x 1 (1Vp - p, 75) Audio monitor outputs: Phono jack (L/R) x 1 (436mVrms, less than 600) Headphone jack: Mini stereo jack x 1 Sound Output (RMS) . . . . 10W + 10W Speaker . . . . . . . . . . . . . 8 cm 13 cm 2 Dimensions . . . . . . . . . . . . 515.8 (W) 582.8 (H) 503.8 (D)mm Weight . . . . . . . . . . . . . . . . approx. 47.2 Kg Specifications subject to change without notice.
Product Code: 111363315
Original Version
Chassis Series: FC3-G2
(Software: AC5-G2)
Give complete "SERVICE REF. NO." for parts order or servicing. It is shown on the rating plate at the cabinet back of the unit. This T.V. receiver will not work properly in foreign countries where the television transmission system and power source differ from the design specifications. Refer to the specification table.
C5DTH
Contents
Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chassis Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 IC Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Service Adjustments with replacing Memory IC (IC802) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12 Service Mode Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14 Service Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Special Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Purity and Convergence Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18 Cabinet Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Chassis Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-29
Safety Notice
SAFETY PRECAUTIONS
1: An isolation transformer should be connected in the power line between the receiver and the AC line when a service is performed on the primary of the converter transformer of the set. 2: Comply with all caution and safety-related notes provided on the cabinet back, inside the cabinet, on the chassis or the picture tube. 3: When replacing a chassis in the cabinet, always be certain that all the protective devices are installed properly, such as, control knobs, adjustment covers or shields, barriers, isolation resistor-capacitor networks etc.. Before returning any television to the customer, the service technician must be sure that it is completely safe to operate without danger of electrical shock.
X-RADIATION PRECAUTION
The primary source of X-RADIATION in television receiver is the picture tube. The picture tube is specially constructed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must be the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X - RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit. Refer to this service manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits, take necessary corrective action. Carefully follow the instructions for + B1 volt power supply adjustment, and high voltage check to maintain the high voltage within the specified limits.
PRODUCT SAFETY NOTICE
Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by mark in the parts list and the schematic diagram designate components in which safety can be of special significance. It is particularly recommended that only parts designated on the parts list in this manual be used for component replacement designated by mark . No deviations from resistance wattage or voltage ratings may be made for replacement items designated by mark .
-2-
RC-IN 28 4 32 31 19 OSD R-OUT OSD G-OUT SDA/SCL R 1 9 8 7 HEATER 19 20 21 B-OUT 1 VERT.OUT HORIZ.OUT Q431 H-DRIVE 34 35 7 17 VIDEO IN 44 INT.VIDEO IN (C-IN) R-Y B-Y 9 Q432 H-OUT FOCUS T471 FBT PCC CIRCUIT Q461-Q462 SCREEN G-OUT R-OUT B G 2 3 G 5/6 IF IN B R OSD B-OUT SDA/SCL SCL 6 X161 3 5
SDA
A1901A RC RECEIVER
IC802 EEPROM
A101 TUNER IC701 TRIPLE VIDEO OUTPUT AMP. SAW FILTER
ON-TIMER
CRT UNIT
D1910 LED
POWER
IC801 CPU
20 21 12 1/2 11 24 R-IN AV1/AV2 OUT G-IN 15 16 B-IN 14 26 TV/AV OUT 11/12
CRT
FRONT CONTROL KEYS
SW1901 ~ SW1906
KEY-IN
S-VIDEO IN (FROM S-TERMINAL)
IC201 IF/VIDEO/ CHROMA
HV L902 DY
6 PWB S-Woofer is not equiped.
IC001 AUDIO AMP.
SP902
R-OUT 12
8
R
Chassis Block Diagrams
SP901
L-OUT 2
6
L VIDEO OUT (TV) 23 46 VIDEO-IN Y-IN 42 27 R-OUT TV-AUDIO T431 H-DRIVE TRANS.
IC501 VERT./DEF.
5
L-OUT
MAIN SIGNAL PROCESSING CIRCUIT
V 5 26 21 (L-TV-L)1/30 2 29 10
VIDEO MONITOR OUT
IC3701
L
AUDIO MONITOR OUT(LEFT)
REAR MONITOR OUT TERMINAL
TV 1 AUDIO OUT
R
AUDIO MONITOR OUT(RIGHT)
V
AV1 VIDEO IN
AV2 VIDEO IN
1 TV IN 5 AV,Y IN 3 4 AV OUT Y-IN 12 11 S-INPUT 9 10 8 AV-IN 13
S-TERMINAL
CDA/SCL (FROM CPU)
-3AUDIO CONTROL/ SURROUND
3 VIDEO MONITOR OUT 28
L
AV1 L-IN
IC281 SECAM
REAR AV1 INPUT TERMINAL
R
AV1 R-IN
SUPER WOOFER UNIT
HV
V
6
L
AV2 L-IN
FRONT AV2 INPUT TERMINAL IC1501 VIDEO SELECTOR
AV IN 2 15 TV IN 1 4 TV/AV OUT Y-OUT MONITOR OUT
R
AV2 R-IN
IC1402 IC1401 SUPER WOOFER AMP. PRE-AMP. 8/9 SUPER WOOFER 4 1
R 6/7
IC1401 VIDEO SELECTOR
+
From IC3701 pin-21 L From IC3701 pin-10
9
POWER SUPPLY CIRCUIT
140V 36V 25V 14 AV-OUT Y-OUT FBT TUNER HORIZ. DEF. VERT. DEF. 24V 13V TV/AV (FROM CPU PIN-24) 12V 9V 5V MAIN SOUND AMP. SURROUND, AV SW. AUDIO CTL, IC201 CPU, EEPROM
C-IN 6
+
Y-IN 7
3 AV1/AV2 (FROM CPU PIN-25) C-IN Y-IN
AV2/S-INPUT
IC001 AUDIO AMP. 29 12
5
SOUND MUTE OUT (MUTE ON=HIGH)
KEY SWITCH IN KEY SWITCH
50/60Hz OUTPUT (60Hz+LOW, 50Hz=HIGH)
SYSTEM CONTROL
IC1401 VIDEO SWITCH IC801 26 CPU QXXAVC305P 11 S-TERMINAL INPUT (S-IN=LOW)
8
AV1/AV2 SWITCH (AV1+LOW, AV2=HIGH)
25
TV/AV SWITCH (TV=LOW, AV=HIGH)
IC1501 VIDEO SWITCH 9/10 24 SCL 2 1 13 9 33
RC SIGNAL IN (ACTIVE=HIGH) AFT SIGNAL INPUT
Chassis Block Diagrams
IC3701 AUDIO CONTROL & SURROUND 13 14 4
SDA
RESET INPUT (RESET=LOW)
5
A101 F/S TUNER
SECAM KILLER INPUT (HIGH=SECAM)
31
POWER ON/OFF (ON=HIGH, OFF=LOW)
PHOTO COUPLE SDA 11 12 SCL
VIF-M OUTPUT (HIGH=NTSC, LOW=OTHER)
-428 10
OSD BLK OUT(Active=High) 22 OSD RED OUT(Active=High)
RC PRE-AMP. 32 6 7 4 SCL SDA 3 17 27
IC201 IF/VIDEO / CHROMA/DEF.
ON-TIMER LED OUT (ON TIMER ON=Low)
LED CPU OSC IN CPU OSC OUT
OSC X801
19 OSD GREEN OUT(Active=High) 20 OSD BLUE OUT(Active=High) 21 18
HORIZ. SYNC IN (ACTIVE=LOW) VERT. SYNC IN (ACTIVE=LOW)
32.768KHz
DEFLECTION CIRCUIT
6
5
POWER PROTECT IN (POWER ERROR=LOW)
IC802 MEMORY
POWER CIRCUIT etc.
IC Block Diagrams
IC201 < IF/Video/Chroma/Def. > LA76818A
DC VOL
BPF
SW
54
Audio Output FM Output/Selected Audio Output PIF AGC RF AGC Output PIF Input1 PIF Input 2 IF Ground IF Vcc FM Filter AFT Output Bus Data Bus Clock ABL Red Input Green Input Blue Input Fast Blanking Input RGB Vcc Red Output Green Output Blue Output fsc output or C Sync output Vertical Output Ramp ALC Filter Horizontal/BUS Vcc Horizontal AFC Filter Horizontal Output
SIF Input SIF APC Filter SIF Output Ext. Audio Input APC Filter VCO Coil 1 VCO Coil 2 VCO Filter Video Output Black Level Detector Internal Video Input (S-C IN) Video/Vertical Vcc External Video Input(Y-IN) Video/Vertical/BUS Ground Selected Video Output Chroma APC1 Filter 4.43 MHz Crystal Clamp Filter Chroma APC2 Filter SECAM R-Y Input (Cr Input) SECAM B-Y Input (Cb Input) CCD/Horizontal Ground CCD Filter CCD Vcc Clock (4MHz) Outupt VCO IREF Flyback Pulse Input
FM DET
LIM AMP
BPF
1 2 3 4 5 6
SPLL
53 52
IF AGC
RF AGC VIDEO DET VIDEO AMP TRAP VIF A2C PLL IF VCC 5V AFT
PEAKING CORING
51 50 49 48
7
8 9 10 11 12 13 14 15 16 17 VCC 19 18 20 21 22 23 24 25 26
PHASE SHIFTER DRIVE/OUT-OFF FSC/ SYNC SW
47
IF IDENT
46 45
DELAY LINE
VIDEO SW
TRAP
CLMP
44
BUS ABL
OSD CONTRAST BRIGHT
42 43 V/C VCC 5V
BLACK STRETCH
SYNC SEP ACC
SW
BPF ON/OFF
CLMP
DC REST
41
APC1
CLAMP VER RAMP HOR VCC H VCC HOR OUT
40
VXO
DEMO
39
TINT
PAL SW
DDS
38
CONTRAST BRIGHT
CLAMP
APC2
VCO
37 36
RGB MATRIX COLOR CLAMP
OSD SW VER C/D
35
CLAMP
DC ADS.
SW +
34 33
1H DELAY
32
VER SEP AFC1 AFC2
30 31 1H VCC
LPF ALC 1/256 HOR C/D HOR VCO
29
FBP
28
27
-5-
1K 10p 0.01u SIF.Out 52 53 500K Det FM Gain 1bit + FM.Level 5bit + 2.5V Chroma C/D Amp Amp SIF VCO SIF. Sys 2bit APC Det
VIF 3
Data Clock SIF.In 54 LIM AMP 500K BPF FM Det Sound BPF Amp prescaller OSC C/D Sound Trap Amp B/N INV IF Ident To BUS Input Select A.SW 1bit A.MUTE 1bit Lock Det VIF Counter To BUS VIF VCO PLL Pull-in SW 50 PIF AGC APC Filter
+
SIF APC Filter 1000p
11 Snd Det Deem-TC 1bit
12
BUS Interface
to BUS Line
IC Block Diagrams
VIF AMP
9
+
PIF In1
1u 46 Video Out 51 VOLUME (ATT) VOLUME Filter VOLUME D/A A.Fil.Def 1bit VOLUME 7bit
+
IF In Video Det
5
0.01u
Deemph
2
FM Out
SAW
VIF 1
VIF 2
FM Mute 1 bit
FM Filter
PIF In2
6
Audio in 10u 1 Audio.out
IC201 LA76818A
9V Video.Level 3bit 2ndIF AGC Chroma VCO Buzz Canceller IF AGC
120K
+/4
VCO Alignment
Reset Pulse
+ To BUS
100K Chroma Counter AFT 49 10 48 VCO COIL1 VCO COIL2 VCO.Coil
IF GND APC Det 3 0.022u 330 0.47u
(6 Vcc)/7
VIF.Sys 2bit
Phase Detector Vcc AFT 100K 0.1u
7
0.47u VCO Ident
-6-/4
RF AGC Out
+
30K
IF AGC Drive
4
RF AGC
RF AGC Delay 6bit
IF VCC
IF AGC Def 1bit
47
+
+
8
VCO Filter
IC Block Diagrams
IC1401 < VIDEO Switch > MM1188XS
SW
CLAMP
IC501 < Vertical Output > TDA9302H/LA78040N
SW
Thermal Protection AMP
6dB
CLAMP
BIAS
CLAMP
(-6dB) 6dB 15K
+
Pump Up
1 IN 3 SW1 L H -
2 Vcc SW2 L L H
3 5 6 8 4 7 SW1 OUT GND IN1-Y IN1-C SW2 OUT IN 1 IN 2 IN 3
9 IN 2
1
2
3
4
5
6
7
Ver. OUTPUT
INVERTING INPUT
PUMP UP OUT
GND
Vcc
IC701 < Triple Video Output Amplifier. > TDA6103Q
6
3x
VDD MIRROR 2 VDD VDD MIRROR 3
VDD
VDD
FLASHDIODE
Cathode Output
(3x)
9,8,7
1x
Vbias
VOC Inverting Input
(3x)
CURRENT SOURCES
1,2,3 Vi
LEVELSHIFTER 1
DIFFERENTIAL STAGE
LEVELSHIFTER 2
5
Non-inverting Input Vip
MIRROR 1
THERMAL PROTECTION
4 Note: One amplifier shown. GND
IC001 < Audio AMP.> AN17820B
+ -
- +
+ -
- +
1
VCC
2
3
4
5
6
7
Input GND
8
IN2
9
Vol.
10
11
12
OUT1 Output OUT1 Standby IN1 (+) (-) GND
OUT2 Output OUT2 (-) (+) GND
-7-
OUTPUT STAGE Vcc
NON INV. INPUT
IC Block Diagrams
IC3701 < Audio Control & Surround > NJW1142M
MONa AGC SR-FIL TONE Ha TONE La OUT a LINEa
5
-2dB
20
6
7
8
10
9
+4.5 dB 13 SDA 14 SCL 11 CVa
IN 1a 1 IN 2a 2 IN 3a 3 IN 4a 4 AGC IN 1b 30 IN 2b 29 IN 3b 28 IN 4b 27 -2dB SEL VOL 1 TONE VOL 2 NJRC ORIGINAL SURROUND & SIMULATED STEREO SEL VOL 1 TONE VOL 2
IIC BUS INTERFACE
12 CVb 19 CTH 18 CTL
25 CSR
15 GND 16 V+ 17 VREF
BIAS
+4.5 dB
26 MONb
24 23 TONE Hb TONE Lb
21 OUT b
22 LINEb
IC281 < Secam Decoder > LA7642NM-TLM-E
EQU-Adj 20 Vcc 19 N.C. 18 Video In 17 Kil-Out 16 AV/SECAM 4.43MHz In 15 14 N.C. 13 SC-In 12 4MHz In 11
ACC
SW3
System
SW2 VCO
Pulse DET
Bell/EQU Adj
Bell/EQU Filter KILLER
SW1
PLL DET Filter Clamp
Pulse I/F
LIM F0 Adj
ID-KIL
ID
SW/ALC
1 F0-Fil
2 Kil-Fil
3 N.C.
4 4.43DC
5 ID-Fil
6 4M-DC
7 R-Y Out
8 N.C.
9 B-Y Out
10 GND
Service Information
I Protection Circuit
This TV set has a built-in power supply protection circuit. It is provided to protect the TV set in case of a power supply circuit malfunctions. When something abnormality occurs during TV reception, the TV set goes to the stand-by mode. When an abnormality occurs during TV reception, it causes pin 27 of the CPU to go continually Low for about one second. The CPU detects that this has occurred and outputs the signal from pin 31 to switch off the power supply lines.
Releasing the protective circuit and restoring power supply
To release the protective circuit and restore power supply, turn the power to the TV set OFF and then ON again via either the main power switch or the ON-OFF button on the remote control. This will work only if the power supply trouble was temporary. If there is permanent trouble such as a damaged circuit, power cannot be restored and the circuit will have to be repaired. -8-
Service Adjustments with Replacing Memory IC(IC802)
Note: The CPU (IC801) and memory IC (IC802) store the service adjustments data and controls data for each circuit.When the Memory IC(IC802) is replaced, some of the service adjustments should be readjusted to obtain the best performance. The necessary service adjustments are carried out by using the RC handset. Please set up the TV set with following steps [1] to [2].
[1] Initializing Procedure
1. Put a new memory IC. 2. Turn on the TV set. 3. Press and hold the TV/AV Selector on the TV set for more than 2 seconds. The following picture appears on the
screen.
TV/AV MENU
-
+
CH
CLR
TV/AV Selector
4. Press the PROGRAMME UP on the TV set while the above On-Screen Display is still on the screen. The following
picture appears on the screen.
TV/AV MENU
-
+
CH
1
PROGRAMME UP This completes the initialization of memory IC. Following shows the initialized contents of memory data by this procedure. - Plug & Play : No executed - Inhibit Data : Cancelled - Ch Skip Data : Cancelled - Sound Volume Data : 10/63 steps. - Volume Lock : OFF - Tuning Lock : OFF - Music Mode : OFF - AV Start : OFF - Colour System : AUTO
[2] Required Service Adjustments
Readjust the following service adjustments. Adjustments Service Mode No. & Item RF AGC Item 01, RF AGC Horizontal centre Item 02, H-PHA Vertical size Item 04, V-SIZ Vertical-S correction Item 05, V-SCO Vertical linearity Item 06, V-LIN Gray scale Item 14-17, 19-21 Further adjustment please refer to page 12 and 13. -9-
Service Adjustments with Replacing Memory IC(IC802)
Following table shows the initial values which have been stored in the CPU ROM, and items for the service adjustments. Service mode adjustments table in CPU ROM
DATA INITIAL RANGE SETUP DESCRIPTION DATA 0~63 0~31 0~63 0~127 0~31 0~31 -16~+15 -64~+32 0~255 0~127 0~7 30 12 40 39 21 20 +3 0 36 45 7 RF AGC Adj. H-Phase (H-Centering) Adj. (50Hz) V-Position (V-Centering) Adj. (50Hz)Fixed. V-Size Adj. (50Hz) V-S Correction (50Hz) V-Linearity Adj. (50Hz) H-PHASE Adj. (60Hz) V-Size Adj. (60Hz) OSD H-Position Adj. OSD Contrast Adj. Correction of the V-size accompanying brightness change. 12 H-SCP 0~7 7 Correction of the H-size accompanying brightness change. 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 SBIAS RBIAS GBIAS BBIAS RDRIV GDRIV BDRIV 0~127 0~255 0~255 0~255 0~127 0~15 00~127 105 0 0 0 64 8 64 Sub Bias Adj. (Do not change) Red Bias Adj. Green Bias Adj. Blue Bias Adj. Red Drive Adj. Green Drive Adj. Blue Drive Adj. White Balance Adj. White Balance Adj. 0~15 0~15 -16~+15 -16~+15 -16~+15 -16~+15 0,1 0~15 0~15 0,1 9 10 0 0 -8 -5 0 8 8 0 0 0 0 3 3 0 0 0 3 0 0 B-Y DC level Adj. R-Y DC level Adj. NTSC B-Y DC level Adj. NTSC R-Y DC level Adj. SECAM B-Y DC level Adj. SECAM R-Y DC level Adj. G-Y angle Adj. R-Y, B-Y Gain Blance Adj. (Do not change.) R-Y, B-Y Angle Adj. (Do not change.) NTSC G-Y Angle Adj. NTSC R-Y, B-Y Gain Balance Adj. NTSC G-Y, B-Y Angle Adj. Coring Gain Adj. Setting of Black stretch start. Setting of Black stretch gain. On and off of ABL. Setting of ABL. Setting of ABL. White peak limitter. Y Gamma setting. Switching of Pre-shoot and Over shoot in AV mode. 84 85 VOLTBL MPP 0~1 0,1 1 0 DATA INITIAL RANGE SETUP SCRIPTION DATA 0~3 0~3 0,1 0~3 -16~+15 2 3 0 0 0 -12 0 0 127 0 0 1 4 16 0 1 1 136 4 34 0 7 7 3 0 0 0 1 0 0 1 1 0 3 0 64 64 25 10 5 2 Pre-shoot/Over shoot Adj. in AV mode. RF Coring Gain Adj. Switching of RF Pre-shoot and Over shoot. RF Pre-shoot/Over shoot Adj. RF Tint Adj. NTSC 4.43 Tint Adj. RF Sharpness Adj. OSD TEXT Contrast. Volume Control Adj. De emphasis TC. VIF System Switch. SIF System Switch. Video Level Adj. FM Level Adj. Over Modulation Switch Audio Monitor Switch SIF Trap Switch ON/OFF Video Level & Modulation Trap Test Horizontal Frequency FBT Blanking Switch Color Killer Option H-Blanking Control. (Left) H-Blanking Control. (Right) RF AFC gain & Gate Adj. RF Vert. Sync. Separation Adj. RF Vert. Count-Down Circuit Adj. AV AFC Gain & Gate Adj. AV Vert Sync. Separation Adj. AV Vert Count-Down Circuit Adj. H Lock, V Detect RF H Lock, V Detect AV C-VCO Adj. Switch C-VCO Adj. Output Pattern Picture AV Blue Back Signal Contrast AV Blue Back Signal Brightness Power Mute Time Adj. Channel Change Mute time Agj. The number of times that a colour system AUTO is judged. Stereo/Mono Option. 0=MONO, 1=SIMPLE AV STEREO, 2,3=AV STEREO Volume Table Multi Personal Preference function on/off o=without M.P.P., 1=with M.P.P.
No. 01 02 03 04 05 06 07 08 09 10 11
ITEM RFAGC H-PHA V-POS V-SIZ V-SCO V-LIN H-P60 V-S60 OSDHP OSDC V-SCP
No. 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83
ITEM PORS RFCO PORWN PORSN TINT
TINT443 -16~+15 SHRF -32~+31
TEXTC -128~+127 VOLUM DEEM VIFSW SIFSW V-LVL FMLVL IFOM-S IFMN-S IFTRAPS IFMLVL TRAP-T H-FRQ FBTS COOP HBLKL HBLKR AFCRF VSRF CDMRF AFCAV VSUAV CDMAV HLVDRF HLVDAV VCO-SW VCO-ADJ CROSS-BW AVNCON AVNBRI POMT CHMT SYST S-STE 0~255 0~1 0~3 0~3 0~7 0~31 0,1 0,1 0,1 0~255 0~7 0~63 0,1 0~7 07 07 0,1 0,1 0~7 0,1 0,1 0~7 0,1 0,1 0,1 0~3 0~3 0~127 0~127 0~127 0~31 0~15 0~3
1-LINE APPEAR DRV B-YD R-YD B-YDN R-YDN SBDC SRDC G-YA RBGB RBAG G-YAN
RBGBN -16~+15 RBAGN -16~+15 COGV BLKS BLKG BRTA BRST BRTH WPL YGAM PORW 0~3 0~3 0~3 0,1 0,1 0~7 0~3 0~3 0,1
-10-
( /JE0110A)
Service Adjustments with Replacing Memory IC(IC802)
No. 86 87 ITEM TUNER AV123 DATA INITIAL RANGE SETUP DESCRIPTION DATA 0,1 0~3 0 1 Tuner Option AV1/AV2/AV3 Option, 0=AV only, 1=AV1, AV2, 2~3=AV1, AV2,AV3 88 OPT POS 0,1 1 Programme number Option, Position No. Option, 0=100 pos., 1=256 pos. 89 GAME 0,1 1 GAME Option, 0=without GAE, 1=with GAME 90 LANGUAGE 0,1 1 Language Option, 0=without Language, 1=with Language 91 OPT COL 0~7 5 Colour System Option, 0~1=PAL only, 2=VMT, 3=China/Indonesia, 4=3 System,5~7=Multi 92 93 OPT SIF OPT BASS 0~7 0~3 3 2 SIF System Option Bass Expander Option, 0=without BASS, 1~2=BASS EXPANDER,3=WOOFER 94 OPT SURR 0,1 1 Surround Option, 0=without SURROUND, 1=with SURROUND 95 96 SUB-BT A-AGC 0,1,2 0,1,2 0 0 Audio IC (NJW1142)Sub Bass Treble adj. Audio IC (NJW1142) AGC adj. No. 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 R00 R01 R02 R03 R04 R05 R06 R07 R08 R09 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 154 242 166 246 3 0 0 0 2 229 144 13 239 141 238 141 237 141 236 141 235 141 33 155 6 33 ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction 366 367 368 369 370 371 372 R12 R13 R68 R69 R70 R71 R72 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0 0 0 0 0 0 160 ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction 345 346 347 348 349 350 351 352 353 354 355 ITEM R26 R27 R28 R29 R30 R31 R32 R33 R34 R35 R36 R37 R38 R39 R40 R41 R42 R43 R44 R45 R46 R47 R48 R49 R50 R51 R52 R53 R54 R55 DATA INITIAL RANGE SETUP DESCRIPTION DATA 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 154 246 0 0 0 0 0 0 0 0 0 0 0 0 107 127 7 3 234 144 3 33 166 249 33 167 34 0 0 0 ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction ROM Correction
Notes: The initial value that the CPU writes down the CPU ROM data to the memory when replaced the memory IC. TV set may not operate correctly with this initial value. It is required to set up the fine adjustment for service adjustments described in the above. -11-
Service Adjustments with Replacing Memory IC(IC802)
[Entering to Service Mode]
1. Press and hold the MENU button on the Remote Control and press the VOLUME (+) button on the TV set.
Following setting items appears on the screen.
MENU
-/--
Display for [RF AGC] RF AGC adjustment
MENU Read Status
SI. 00100101S2.11111000 ADDRESS DATA 01 RF AGC 30
TV/AV MENU
-
+
CH
Item No.
Item
Data value
2. Select item by pressing the TIMER (Item No. UP) or SOUND MUTE (Item No. DOWN) button on the remote control
handset.
TIMER
01`02`03`04`05......84...
...84`83`82`81`80......01
Example Display for [V-SCO] V-S Correction adjustment
-/--
Display for [DRV] White balance adjustment
-/--
Read Status
SI. 00100101S2.11111000 ADDRESS DATA 05 9 05 V-SCO
Read Status
SI. 00100101S2.11111000 ADDRESS DATA 21 DRV R 64 B 64
Data value for Blue
Item No.
Item
Data value
Item No.
Item
Data value for Red
3. Adjust data value by pressing the VOLUME + or VOLUME - button on the remote control handset. -/-CH
CH
To return to normal TV mode, press the MENU button on the TV set or the remote control handset.
-12-
Service Mode Adjustments
Following adjustments should be carried out when the memory IC is replaced. How to enter the service mode and adjust values, please refer to " Entering to Service mode" on page 12.
Item 01 [RF AGC] AGC
NOTE: Do not attempt this adjustment with weak signal. (1) Tune the receiver to most clearest (or strongest) VHF station in your area. Set the brightness and contrast controls to maximum. Set the colour control to minimum. (2) Select [RF AGC] in the service mode. (3) Change value until the snow noise just disappears. (4) Exit from service mode.
Item 05 [V-SCO] V-S CORRECTION
(1) Receive a crosshatch pattern. (2) Set the lever of SW501 (Vertical Center SW) as the position of a center. (3) Select a picture mode of NATURAL by pressing the PICTURE MODE button. (4) Select [V-SCO] in the service mode. (5) Adjust Vertical S-letter Correction so that the difference of "c", "d" and "e" becomes less than 2 mm by pressing the VOLUME + or - button. (6) Confirm Vertical Linearity and adjust Vertical Center then Vertical Size. (7) Exit from service mode.
Item 02 [H-PHA] HORIZONTAL CENTRE
(1) Receive a monochrome circular pattern. (2) Set the brightness and contrast to normal. (3) Select [H-PHA] in the service mode. (4) Change value to be optimum horizontal centre position. (5) Exit from service mode.
c
Upper
d e
Center Bottom
Horizontal centre
Item 06 [V-LIN] VERTICAL LINEARITY
(1) Receive a crosshatch pattern. (2) Set the lever of SW501 (Vertical Center SW) as the position of a center. (3) Select a picture mode of NATURAL by pressing the PICTURE MODE button. (4) Select [V-LIN] in the service mode. (5) Adjust Vertical Linearity so that the difference of "a" and "b" becomes less than 3mm by pressing VOLUME + or - button. (6) Exit from service mode.
Upper
Item 04 [V-SIZ] VERTICAL SIZE
(1) Receive a monochrome circular pattern. (2) Set the lever of SW501 (Vertical Center SW) as the position of a center. (3) Set the brightness and contrast to maximum. (4) Select [V-SIZ] in the service mode. (5) Change value to be optimum vertical size. (6) Exit from service mode.
a
Vertical size
b
Center
Bottom
J2
J
J112
Q261
J1003
J113
J506
R264
R426
JW31
JW34
JW32
J239
D421
JP501
J017
D1032
C1401
R872
J508 J507
J10
SW501
J1004
J509
SW501
R503
JW37
JP1401
E JP140
JP503
R502
J409 J410 J408
Q461-H1
D501
J505
C470
R473
R540
J019
D465
Q461
D642
J630
VR462
R501
C461
R478
R468
E
Q540 C540
J022
C150
Q461A
E
H-SIZE
VR463
C467
C463
Q462
JWW1
R467
R469
J411
R463
C521
C462
JW40
PCC
J501
IC501-H3
Q461-H2
JP463
R471 R472
R461 C466 R464 D462
D512
445
D461 R466 R480
J503
C468
R465
C524
R516
R514
J502
-13-
Service Mode Adjustments
Items 14-17, 19-21 GREY SCALE
(1) Receive a monochrome circular pattern. (2) Set the brightness and colour to normal, contrast to maximum. (3) Enter to the service mode. (4) Select No. 14 RBIAS (Red Bias), No, 15 GBIAS (Green Bias), and No. 16 BBIAS (Blue Bias) and set each data to 0 by pressing the VOLUME + or - key. (5) Select No. 17 RDRIV (Red Drive) and No. 19 BDRIV (Blue Drive) and set each data to 64 by pressing the VOLUME + or - key. (6) Turn Screen Control on the FBT (T471) to minimum (fully counter-clock-wise). (7) Select No. 20 (1-line appear). (8) Advance Screen Control clockwise to obtain just visible one colour line. If line does not appear, place this control to maximum (fully clockwise). (9) Raise each Bias Level with 1, 2, 5, 6, 9 and 0 keys to obtain just visible white line. (10) Select No. 21 DRV (Drive Adjustments). (11) Adjust Red and Blue Drive Levels alternately with 3, 4, -/-- or RECALL key to produce normal black an white picture in highlight areas. (12) Check for proper grayscale at all brightness levels. To turn off the TV Service Menu display, press the MENU key. Note: If the Grayscale adjustment is made after picture tube replacement, check the High Voltage
TV/AV
MAIN BOARD
P P
Red Bias +
TIMER
Red Drive -
435
P435
C423-H1
C437A
C437B
C437
R424
JP411
R355
C423-H2
C423-H3 C420-H3
JP436
JP412 JP410
JW1
C420-H2
C420-H1
C420
Red Bias T471-H4
T471-H2
D438
T471-H1
T471
Red Drive + Green Bias -/--
Green Bias + Blue Bias MENU
JP403A JP403
J405
T471-H5
T471-H6
JP404
T471-H7 T471-H11
T471-H8
T471-H10
JP405 R481A
JP409 JP408
R492
JP407 R477A R481
JW6
J406
R487
R477 C471
1
JP483
CH
Blue Bias +
T471A
JP477
R4 8
3
R
FC3G2 CHASSIS
Press the MENU button to exit from service mode.
CH
Blue Drive CH SCAN
Blue Drive +
A ·B BASS SWAP SOUND
SCREEN VR (Under side)
PICTURE SURROUND C.SYS
S.SYS
JXMRM
-14-
Service Adjustments
Following adjustments are not required to readjust when replacing the memory IC.
B-VOLTAGE SUPPLY CHECKING
(1) Connect DC meter to TP-B and the ground. (2) Tune the receiver to an active channel and synchronized picture. Select NATURAL picture mode by pressing the PICTURE MODE button on the remote control. (3) Adjust B-voltage to be 140 ± 1V DC by using VR651. MAIN BOARD
C609 H2 91
HIGH VOLTAGE CHECK
Note: +B (+140V) Voltage Check and Grayscale Adjustment must be completed before attempting High Voltage Check. (1) Connect high voltage voltmeter negative lead to ground, and connect + lead to anode of picture tube. (2) Tune receiver to an active channel and confirm TV is operating properly. (3) Maximize the beam current by adjusting the contrast and brightness controls to maximum. Confirm high voltage is within 28.0 KV and 30.0 KV at maximum beam current. (4) Eliminate the beam current by adjusting the contrast and brightness controls to minimum. Confirm high voltage does not exceed 32.0 KV at zero beam current. If reading is not within range, check horizontal circuit. No high-voltage adjustment is provided on this chassis.
C654
D654
C609A-H2 C609A-H1 R614 C611 R616 R632 D615 J607
Q613-H5
C690
J619 J618 C653
D861
JW7
C609
D654-H2
D654-H1
R620
R621
R646
J615
IC681
C614 D614
C609-H1
R625
J638
D692
C681
J616
J821
R626
Q653
E C664 Q651 E
JW14
!
J606
C618
C618A
5
IC802
JW15
C657 R656
R611 E Q625 R641 E Q641 R642 R643 Q642 E
D641
R613
R659
R615
R613A
J611 J612 C643
J604
3 4 D610
2
R658
8
J617 R651
D664
D643 D619 R627 L614 R619 D612 J608
Q613-H1
1
D655
J605
D659
R633
C665
L616
1
R668
16
R669
R657
T611-H2 Q613A
T611-H17
T611B-H17
J624
Q654
Q613
R644 C644 C613 R622
T611-H3
Q613-H2
D653
L653 L654
J621 J622
JW35
R672
R655
T611-H4
R631
Q613-H3
D652
R645
T611-H14
J623
E Q652
Q611 E Q612
L652
T611B-H14
C615
R653
C656
JW13
E
R660 R671 R652 E Q681 D671 J626 C655
J2 R681
D693
T611-H13
T611B-H13
L615
R623
D617 J609 L612
T611-H7
T611-H12
T611B-H12
JW12
T431
JP431
R628 R629
T431-H2 T431-H4
9 H13 T611B-H12
L651
L613
C355
B-Voltage Supply Adjustment
FOCUS ADJUSTMENT
(1) Receive the monochrome circular pattern. (2) Set the brightness to normal and contrast to maximum. (3) Adjust the focus control on the F.B.T. for the best focus on the screen centre.
MAIN BOARD
D
JP441A
C515
R5
T
C442 H1
JP441
KDY
D439
C442
C441
C441-H1
R442 KDY-1 D485 R487 R441 C487 JP436
T611B
C442-H3
T611
J406
C425
C442-H2 Q432-H1 C441-H2 C423-H1 C420-H1
R492 R477A R481
Q432-H2
C424
C423
C423A
7
C423-H3
C420-H3
JP404 JP405 JP483
JW6
Q432-H3
C424A
C423-H2
L613
C420-H2
TP-B
Q432
J609 L612
JP407
J404 C617 D611
C629
Q432B
J403
R435
JP435
JW1
T471-H1
T471-H10
R434
C432
T471-H8
C433
617
Q613-H4
R423
C437
T471-H2 T471-H11
R4
R481A
C471
FC3G2 CHASSIS
T471
D438
JP409 JP408
T611-H7
C425A
L432
1
C420
Q432A
83
R475
C441-H3
R488
KQ
R624 D616
7
Q613-H6
JW33
JW8
J625
J603
C617
D611
Q662 E
T611B
9
Q613-H4
D651
T611A
10
J627
!
JP633
R
5 69
E
T611
C434
C629
C652
VR651
C639
R431 E
T431A
R434
JW11
JW10
R661
Q431 R433
T431-H1 T431-H3
J401
TP-B
C425A J403
D439
L462
C651
JP631 R665
L462-H2 L462-H3
D662
C432
TP-B
Q432B
C424A
C424
Q432A
C425
L432
D661
R663
C465
R664
R103
J63
L462-H1
R445
J402
Q432-H3 Q432-H2
Q432-H1 C442-H2
C442
C442-H3
JP441A
C462
Q462
J630
JP5
E
R480
C442-H1
C433 L431 R423
Q432
C441-H2 C441-H
C441
C44
J411
R468
J409 J410 J408 R478
J404
L461
L441-H3
R471
JWW1
L441-H1
L441
L441
C423A
R4
C423
R485 R484
C491
C486
L431
15 623
Q613-H6
T431-H1
T431-H3
T471-H7
D616
C355
R422
JP412
!
R431 C434
E
JP431
T431A
T471-H6 T471-H4
C437A
R624 Q612
T471-H5 JP403 T471A
JP410 JP411 JP403A
T431-H2
T431-H4
R424
J405
R355
R477
T431
R628
R629
JP477
Q431
C437B
R433
Focus VR (Upper side)
-15-
Special Function
The following special functions can be set up on this TV set.
How to set the special function:
Note: When making the VOLUME LOCK setting, set the desired maximum sound volume by pressing the VOLUME + or - button before entering Special Function setting mode. To enter into the special function setting mode, press and hold the MENU button of the remote control, then press the PROGRAMME DOWN button on the TV set.
MENU
(1) Volume Lock setting
With this function, a maximum sound volume limit can be set at any level.
1
SOUND
IIII IIII
-/--
(2) Tuning Lock setting
Once TUNING LOCK is switched on, further channel tuning (Pre-set) is not possible. The Channel Swapping function also is not possible.
VOLUME LOCK TUNING LOCK MUSIC MODE AV START
OFF OFF OFF OFF
-
+
CH
SELECT ADJUST
M EXIT
TUNING LOCKED
2
(3) Music Mode setting
When Music Mode is ON, Programme position from "247" to "255" and "0" are set Music Mode. Only sound is provided and any picture is not on the screen under Music Mode. Turns black screen
Select an item of the special functions by pressing the PROGRAMME UP or DOWN button on the remote control or the TV set. -/--
CH
VOLUME LOCK TUNING LOCK MUSIC MODE AV START
OFF OFF OFF OFF
CH
SELECT
ADJUST
M EXIT
MUSIC
3
(4) AV Start setting
Set AV-START to ON and every time the TV set is switched on, AV position will be the initial programme position.
Set the selected special function " ON " by pressing the VOLUME + or - button. To cancel, set to " OFF". -/--
CH
VOLUME LOCK TUNING LOCK MUSIC MODE AV START
OFF ON OFF OFF
CH
AV1
SELECT
ADJUST
M EXIT
4
Press the MENU button of the remote control to return to the normal TV mode.
MENU
-/--
-16-
Purity and Convergence Adjustment
CAUTION: The Convergence and Purity adjustments have been made at the factory. Readjustment should be made only after picture tube or deflection yoke replacement, following the steps below:
Signals: Use a pattern generator which can output red, green, blue and white raster and crosshatch pattern signals. Procedure: Carry out purity adjustment first, and then carry out convergence adjustment. Preparation: The deflection yoke may have several correction magnets attached to its outer edge. If replacing the picture tube, the positions of the magnets can be changed and they can be re-used, so remove these magnets and keep them safely so that they do not get lost. Figure 1
Rubber wedge
Correction magnet Deflection yoke mounting scrrew
PURITY ADJUSTMENTS
1. Place the picture so that its front faces west. 2. Insert the power plug into a wall outlet, and then turn on the power for the TV and de-magnetize the TV using its own degaussing circuit. 3. Loosen the screw which is holding the deflection yoke (with integrated purity magnets), and them move the deflection yoke forward as far as it will go. Remove the rubber wedge at this time. 4. Turn off the red and blue raster so that only the green raster is on. 5. Adjust the angle between the tabs (wings) on purity magnets to center the vertical green belt in the picture tube screen. (See Figures 2 and 3.) NOTE: This adjustment can only be carried out by changing the angle, not by rotating the tabs up and down. 6. Gently move the deflection yoke back to the position where the green band fills the whole of the picture tube screen, and then tighten the screw to secure the deflection yoke in place. 7. If there is any color distortion around the edges, correct it by attaching magnets to the outer edge of the deflection yoke. The magnets should be attached so that the line running from the position of the distortion to the center of the picture tube intersects the deflection yoke. The colors on the magnets indicate the north and south poles of the magnets. Attach the magnets in whichever direction causes the distortion to disappear.(See Figures 1 and 4. The south and north pole positions are shown as a guide.) 8. Switch the screen to red and blue rasters and check that there is no color distortion. If there is any distortion, adjust the angles of purity magnets tabs or the forwardback position of the deflection yoke, or change the attachment positions of the N correction magnets.
Move the deflection yoke back and forth to adjust the purity
Figure 2 Change the angle to adjust the green band so that it is centered in the screen. FOUR-POLE MAGNET TABS SIX-POLE MAGNET TABS
ANGLE OF TABS
1
2
3 4
PURITY MAGNET TABS Figure 3
GREEN band
Figure 4
Color Distortion Magnet attachment position Deflection Yoke outer edge
S
-17-
Purity and Convergence Adjustment
CONVERGENCE ADJUSTMENT
Preparation: After carrying out purity adjustment and before proceeding to convergence adjustment, provisionally insert the rubber wedge so that there is no vertical or sideways play in the deflection yoke. Signals: Display a crosshatch pattern. 1. Red/blue center adjustment Adjust the angle between the tabs (1) and (2) in Figure 5 and rotate them together until the lines of the red and blue crosshatch patterns (vertical and horizontal lines) are superimposed in the center of the screen. 2. Green and red/blue center adjustment Adjust the angle between the tabs (3) and (4) in Figure 5 and rotate them together until the lines of the green crosshatch pattern are superimposed with the red/blue crosshatch pattern (vertical and horizontal lines) which were superimposed in step 1). 3. Vertical lines at screen center (Red and Blue) Use the VR2 control (see Figure 8) at the top of the deflection yoke to correct the vertical line convergence at the center of the screen.(See Figure 9.) 4. Vertical lines at screen top and bottom Use the VR1 control (see Figure 8) at the top of the deflection yoke to correct the vertical line convergence at the top and bottom of the screen. (See Figure 10.) 5. Horizontal lines at screen top and bottom Rotate the Deflection yoke to the left or right to correct the horizontal line convergence at the top and bottom of the screen. (See Figure 11.) If vertical lines are intersecting at the top and bottom, use a screwdriver to adjust the Balance coil at the top of the deflection yoke. (See Figure 12.) Figure 8 VR1 Figure 9 Figure 5
FOUR-POLE MAGNET TABS SIX-POLE MAGNET TABS
ANGLE OF TABS
1
2
3 4
PURITY MAGNET TABS
Figure 6 Adjust the angle rotation of tabs (1) and (2) to align the vertical and horizontal lines.
Red Blue
Figure 7 Adjust the angle and rotation of tabs (3) and (4) to align the vertical and horizontal lines.
Red/Blue Green
Use the VR2 control to correct.
Red Blue
Figure 10
Use the VR1 control to correct.
Blue Red
Figure 11 Balance coil
Red Blue
VR2
Rotate the DY to correct.
Figure 12
Red Blue
Use the Balance coil to correct
-18-
Cabinet Parts List
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
C5DTH
7
6
AV1 INPUT
MONITOR OUT
R AUDIO L
S-VIDEO
(MONO)
ANT. 75
VIDEO
TV/AV MENU
-
+
CH
8 9
TV/AV
5-a
4 5-b
3
2
1
TIMER
P
P
MENU
-/--
10
CH
CH
CH SCAN A ·B BASS SWAP SOUND
PICTURE SURROUND C.SYS
S.SYS
JXMRM
Key No.
1
Part No.
306 229 299 306 104 019 316 316 307 041 040 9067 8406 9136 9074 2505 2449 2324 2447 0292 7269 4672
Description
BUTTON POWER-C5GT SPRING-E3HA DEC.IND-C5GA BUTTON UNITED-C5GSR LATCH PUSH,7.9X6.9BK LATCH PUSH,7.9X6.9BK ASSY,CABINET FR-C5DTH CABINET FRONT-C5DTH DOOR-C5GT BADGE,SANYO*43.5X10L43.5 BADGE,SANYO*43.5X10L43.5 CABINET BACK-C5DTR HOLDER AC CORD-SGP-D4VA ASSY,REMOCON JXMRM RC-BATTERY LID-JXMRA INSTRUCTIONS MANUAL-C5GSH
Key No.
Part No.
Description
610 610 2 610 3 610 4 610 or 645 5 610 5-a 610 5-b 610 6 645 or 645 7 8 9 10
610 308 7580 610 256 7670 645 067 5089 610 297 3723 610 315 8853
-19-
Chassis Electrical Parts List
C5DTH
Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by a ! mark in this parts list and the circuit diagram show components whose value have special significance to product safety. It is particularly recommended that only parts specified on the following parts list be used for components replacement pointed out by the mark.
Note: Parts order must contain Service Ref. No., Part No., and descriptions. The main PCB unit will be supplied without tuner and flyback transformer. They should be ordered separately.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
NOTES:
Read description in the Capacitor and Resistor as follows: CAPACITOR CERAMIC 100P K 50V
Rated Voltage Tolerance Symbols: Less than 10pF A : Not specified B : ±0.1pF D : ±0.5pF F : ±1PF R : ±0.25-0pF S : ±0-0.25pF More than 10pF A : Not specified B : ±0.1% D : ±0.5% F : ±1% H : ±3% J : ±5% L : ±15% M : ±20% P : +100-0% Q : +30-10% U : +75-10% V : +20-10% X : +40-20% Y : +150-10%
OUT OF CIRCUIT BOARD
PICTURE TUBE
!
Q901 Q901A Q901B1
C : ±0.25pF G : ±2pF E : +0-1pF C : ±0.25% G : ±2% K : ±10% N : ±30% T : +50-10% W : +100-10% Z : +80-20%
Q901B2
Q901B3
Q901B4
4140123506 6100031739 6450088674 6102904154 6102337891 6101170154 6102904154 6102337891 6101170154 6102904154 6102337891 6101170154 6102904154 6102337891 6101170154
CRT A68QCU770X60L CG PURITY MAGNET MAGNET,CG.PR DY SPACER-F8LZ DY SPACER E2HA DY SPACER-D4AK DY SPACER-F8LZ DY SPACER E2HA DY SPACER-D4AK DY SPACER-F8LZ DY SPACER E2HA DY SPACER-D4AK DY SPACER-F8LZ DY SPACER E2HA DY SPACER-D4AK
Rated value: P=pico farad, U=micro farad Material: CERAMIC........... Ceramic MT-PAPER......... Metallized Paper POLYESTER...... Polyester MT-POLYEST.....Metallized Polyester POLYPRO.......... Polypropylene MT-POLYPRO....Metallized Polypropylene COMPO FILM.....Composite film MT-COMPO........Metallized Composite STYRENE...........Styrene TA-SOLID........... Tantalum Solid AL-SOLID........... Aluminium Solid ELECT................ Electrolytic NP-ELECT..........Non-polarised Electrolytic OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic DL-ELECT.......... Double Layered Electrolytic
COIL
!
L901
6450552168
COIL,DEGAUSSING
MISCELLANEOUS
SP901 SP902 ! W901 W903 6450553653 6450553653 6450399251 6450646096 6103052182 SPEAKER,8 SPEAKER,8 CORD,POWER-2.0MK-A5003 CORD,POWER-2.0MK-A5003 ASSY,WIRE GND CONNECTOR C
ASSY,PWB,MAIN C5DTH 1AA0B10S131FA
TRANSISTOR
Q1003 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4050144519 4050144618 4050158724 4050158922 TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR 2SC2412K T146 2SC2412K T146 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SC2412K T146 2SC2412K T146 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SC2412K T146 2SC2412K T146 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SC2412K T146 2SC2412K T146 2SC2812-L6-TB 2SC2812-L7-TB R S
RESISTOR CARBON 4.7K
J
A
1/4W
Rated Wattage
Performance Symbols: A: General B: Non flammable Z: Low noise Other: Temperature coefficient Tolerance Symbols: A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5% F: ±1% G: ±2% J: ±5% K: ±10% M: ±20% P: +5-15% Rated value, ohms: K: 1,000, M: 1,000,000 Material: CARBON........... Carbon MT-FILM............ Metal Film OXIDE-MT......... Oxide Metal Film SOLID................ Composition MT-GLAZE......... Metal Glaze WIRE WOUND... Wire Wound CERAMIC RES.. Ceramic FUSIBLE RES.... Fusible
Q1004
R S
Q1005
R S
Q1006
R S
-20-
C5DTH
Ref. No.
Part No.
4051739813 4051739912 4050159721 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4051843411 4051345925 4051472215 4050020318 4050020417 4050026726 4050026924 4051631513 4051632718 4060087407 4050017417 4050017615 4050043119 4050043218 4050061717 4050061816 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051843411 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051843411 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051843411 4051345925 4051472215 4050020318 4050020417 4050026726 4050026924 4051631513 4051632718 4060087407 4050017417 4050017615 4050043119 4050043218 4050061717 4050061816
Description
TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR 2SC3928A1R 2SC3928A1S 2SC2814-F4-TB 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SA1037AK-T146-R 2SA1037AK-S-T146 2SA1037K T146 R 2SA1037K T146 S 2SA1179-M6-TB 2SA1179-M7-TB 2SA1179N-M6-TB 2SA1179N-M7-TB 2SA1015-G(SAN)-TPE2 2SA1015-O(SAN) 2SA1015-Y(SAN) 2SA564A-Q(CU) 2SA564A-R(CU) 2SA933S-Q 2SA933S-R 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SA1037AK-T146-R 2SA1037AK-S-T146 2SA1037K T146 R 2SA1037K T146 S 2SA1179-M6-TB 2SA1179-M7-TB 2SA1179N-M6-TB 2SA1179N-M7-TB 2SA1015-G(SAN)-TPE2 2SA1015-O(SAN) 2SA1015-Y(SAN) 2SA564A-Q(CU) 2SA564A-R(CU) 2SA933S-Q 2SA933S-R
Ref. No.
Q261
Part No.
4060087407 4050017417 4050017615 4050043119 4050043218 4050061717 4050061816 4050180517 4050180616 4051571304 4050647307 4050647406 4050118411 4050118510 4050118619 4050122012 4050122111 4050122319 4050207511 4050207719 4050207917 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051843411 4050118411 4050118510 4050118619 4050122012 4050122111 4050122319 4050207511 4050207719 4050207917 4050136712 4050136811 4050137016 4050066514 4050066712 4051690906 4050136811 4050137016 4060087407 4050017615 4050043218 4050061816 4050118411 4050118510 4050118619 4050122012 4050122319 4050207511 4050207719 4050118411 4050118510 4050118619 4050122012 4050122319 4050207511 4050207719 4051381309 4050599804
Description
TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR 2SA1015-G(SAN)-TPE2 2SA1015-O(SAN) 2SA1015-Y(SAN) 2SA564A-Q(CU) 2SA564A-R(CU) 2SA933S-Q 2SA933S-R 2SC3332-R 2SC3332-S 2SD2634-YB 2SB1274-Q-RA 2SB1274-R-RA 2SC1740S-Q 2SC1740S-R 2SC1740S-S 2SC1815-GR 2SC1815-O 2SC1815-Y 2SC945A-PA 2SC945A-QA 2SC945A-RA 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SC1740S-Q 2SC1740S-R 2SC1740S-S 2SC1815-GR 2SC1815-O 2SC1815-Y 2SC945A-PA 2SC945A-QA 2SC945A-RA 2SC2274-D 2SC2274-E 2SC2274-F 2SA984-E 2SA984-F 2SK3528 2SC2274-E 2SC2274-F 2SA1015-G(SAN)-TPE2 2SA1015-Y(SAN) 2SA564A-R(CU) 2SA933S-R 2SC1740S-Q 2SC1740S-R 2SC1740S-S 2SC1815-GR 2SC1815-Y 2SC945A-PA 2SC945A-QA 2SC1740S-Q 2SC1740S-R 2SC1740S-S 2SC1815-GR 2SC1815-Y 2SC945A-PA 2SC945A-QA 2SB1565-E 2SD1913-Q-RA
Q111 Q122
Q431 Q432 Q461 Q462
Q1401
Q1402
Q527
Q1501
Q540
Q1503
Q611
Q612 Q613 Q625 Q641
Q1504
Q642
Q190
Q651
Q1902
Q652 Q654
-21-
C5DTH
Ref. No.
Part No.
4050599903 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4051843411 4060087407 4050017417 4050017615 4050043119 4050043218 4050061717 4050061816 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4051843411 4050118411 4050118510 4050118619 4050122012 4050122111 4050122319 4050207511 4050207719 4050207917 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051843411 4050118411 4050118510 4050118619 4050122012 4050122319 4050207511 4050207719 4050144519 4050144618 4050158724 4050158922 4051739813 4051739912 4051843411 4051345925 4051472215 4050020318 4050020417 4050026726 4050026924 4051631513 4051632718 4050144519 4050144618 4050158724 4050158922 4051631612
Description
TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR 2SD1913-R-RA 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SA1015-G(SAN)-TPE2 2SA1015-O(SAN) 2SA1015-Y(SAN) 2SA564A-Q(CU) 2SA564A-R(CU) 2SA933S-Q 2SA933S-R 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SC1740S-Q 2SC1740S-R 2SC1740S-S 2SC1815-GR 2SC1815-O 2SC1815-Y 2SC945A-PA 2SC945A-QA 2SC945A-RA 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SC1740S-Q 2SC1740S-R 2SC1740S-S 2SC1815-GR 2SC1815-Y 2SC945A-PA 2SC945A-QA 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX 2SA1037AK-T146-R 2SA1037AK-S-T146 2SA1037K T146 R 2SA1037K T146 S 2SA1179-M6-TB 2SA1179-M7-TB 2SA1179N-M6-TB 2SA1179N-M7-TB 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0
Ref. No.
Part No.
4051631711 4051739813 4051739912 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051345925 4051472215 4050020318 4050020417 4050026726 4050026924 4051631513 4051632718 4050144519 4050144618 4050158724 4050158922 4051631612 4051631711 4051739813 4051739912 4051843411
Description
TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SA1037AK-T146-R 2SA1037AK-S-T146 2SA1037K T146 R 2SA1037K T146 S 2SA1179-M6-TB 2SA1179-M7-TB 2SA1179N-M6-TB 2SA1179N-M7-TB 2SC2412K T146 R 2SC2412K T146 S 2SC2812-L6-TB 2SC2812-L7-TB 2SC2812N-L6-TB0 2SC2812N-L7-TB0 2SC3928A1R 2SC3928A1S 2SD0601A-R-TX
Q661
Q881
Q662
Q882
Q663
Q886
Q681
INTEGRATED CIRCUIT
IC001 IC1401 IC1501 IC201 IC202 4095752202 4094793216 4090512910 4095175912 4092415407 4091245302 4091721509 4095646115 4095644319 4094535905 4092415407 4092654806 4091721509 4093205700 4104862007 4104958007 4094594506 IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC AN17820B MM1188XS TC4053BF-TP1 LA76818A BA178M05T L78M05T MC78M05CT LA7642NM-TLM-E NJW1142M LA78041 BA178M05T L78M05CV MC78M05CT UPC78M05AHF LC863448W-XXXX-TLM AT24C16A-10PI-2.7 24LC16B/P
Q690
Q693
IC281 IC3701 IC501 IC681
IC801 IC802
Q818
CAPACITOR
C001 C011 C021 C031 C1000 C1001 C1002 C101 C1030 4040886600 4030459867 4040848806 4030490018 4040848806 4030490018 4040849308 4030513123 4040847700 4030418824 4040847700 4030418824 4040847700 4030418824 4040848301 4030441743 4040847700 4030418824 ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT 2200U 2200U 1U 1U 1U 1U 47U 47U 10U 10U 10U 10U 10U 10U 470U 470U 10U 10U M M M M M M M M M M M M M M M M M M 25V 25V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 16V 16V 16V
Q861
Q871
-22-
C5DTH
Ref. No.
C1031 C1032 C106 C1060 C1061 C1062 C1063 C1064 C1065 C1066 C107 C1081 C1082 C1084 C111 C112 C113 C120 C121 C122 C123 C124 C132 C135 C138 C1401 C1402 C1501 C1502 C171 C172 C174 C1902 C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C212
Part No.
4040847700 4030418824 4040847700 4030418824 4040849308 4030513123 4040847700 4030418824 4040847700 4030418824 4040848004 4030430222 4040848905 4030494224 4040848905 4030494224 4040848905 4030494224 4040848905 4030494224 4040849308 4030513123 4032152211 4040847700 4030418824 4032152211 4032152211 4032152211 4032152211 4032844314 4032152211 4040847809 4030422425 4011057919 4032152211 4040848707 4030486328 4040848707 4030486328 4032844314 4040847809 4030422425 4032152211 4032152211 4040848905 4030494224 4031552111 4032152211 4031571914 4040875406 4030502810 4040849803 4030862310 4032499039 4032152211 4040848905 4030494224 4040848905 4030494224 4033053517 4033053517 4031133815 4040848707 4030486328 4040848400 4030451534 4031554214
Description
ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC ELECT ELECT CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC ELECT ELECT MT-GLAZE CERAMIC ELECT ELECT ELECT ELECT CERAMIC ELECT ELECT CERAMIC CERAMIC ELECT ELECT CERAMIC CERAMIC CERAMIC ELECT ELECT NP-ELECT NP-ELECT MT-COMPO CERAMIC ELECT ELECT ELECT ELECT CERAMIC CERAMIC CERAMIC ELECT ELECT ELECT ELECT CERAMIC 10U M 16V 10U M 16V 10U M 16V 10U M 16V 47U M 50V 47U M 50V 10U M 16V 10U M 16V 10U M 16V 10U M 16V 220U M 16V 220U M 16V 10U M 50V 10U M 50V 10U M 50V 10U M 50V 10U M 50V 10U M 50V 10U M 50V 10U M 50V 47U M 50V 47U M 50V 0.01U K 50V 10U M 16V 10U M 16V 0.01U K 50V 0.01U K 50V 0.01U K 50V 0.01U K 50V 0.022U K 50V 0.01U K 50V 100U M 16V 100U M 16V 0.000 ZA 1/16W 0.01U K 50V 0.47U M 50V 0.47U M 50V 0.47U M 50V 0.47U M 50V 0.022U K 50V 100U M 16V 100U M 16V 0.01U K 50V 0.01U K 50V 10U M 50V 10U M 50V 1500P K 50V 0.01U K 50V 10P D 50V 22U M 50V 22U M 50V 1U M 50V 1U M 50V 0.015U J 50V 0.01U K 50V 10U M 50V 10U M 50V 10U M 50V 10U M 50V 0.1U Z 50V 0.1U Z 50V 1000P K 50V 0.47U M 50V 0.47U M 50V 1000U M 25V 1000U M 25V 15P J 50V
Ref. No.
C218 C219 C221 C222 C223 C224 C225 C226 C227 C231 C232 C233 C240 C243 C244 C245 C246 C247 C273 C275 C276 C277 C278 C280 C281 C282 C283 C284 C285 C286 C287 C288 C289 C291 C302 C355 C358 C3701 C3702 C3710 C3711 C3712 C3714 C3715
Part No.
4011057919 4032152211 4033053517 4033053517 4033053517 4033670417 4040848806 4030490018 4040848806 4030490018 4040849803 4030862310 4032602944 4032602944 4040848905 4030494224 4032152211 4032152211 4040849308 4030513123 4040849803 4030862310 4040848806 4030490018 4040849001 4030499823 4033053517 4040849308 4030513123 4040849308 4030513123 4040871606 4030478422 4033053517 4032152211 4040848806 4030490018 4032152211 4032152211 4040848806 4030490018 4040849803 4030862310 4040848806 4030490018 4040849803 4030862310 4030608433 4031791619 4040848905 4030494224 4031818217 4031133815 4030708410 4040848806 4030490018 4040847908 4030424875 4033423310 4040849209 4030510627 4040849209 4030510627 4040849209 4030510627 4031134119 4033423310
Description
MT-GLAZE CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC ELECT ELECT ELECT ELECT NP-ELECT NP-ELECT MT-COMPO MT-COMPO ELECT ELECT CERAMIC CERAMIC ELECT ELECT NP-ELECT NP-ELECT ELECT ELECT ELECT ELECT CERAMIC ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CERAMIC ELECT ELECT CERAMIC CERAMIC ELECT ELECT NP-ELECT NP-ELECT ELECT ELECT NP-ELECT NP-ELECT POLYESTER POLYESTER ELECT ELECT POLYESTER CERAMIC CERAMIC ELECT ELECT ELECT ELECT CERAMIC ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CERAMIC 0.000 ZA 1/16W 0.01U K 50V 0.1U Z 50V 0.1U Z 50V 0.1U Z 50V 0.1U K 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 0.33U J 50V 0.33U J 50V 10U M 50V 10U M 50V 0.01U K 50V 0.01U K 50V 47U M 50V 47U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 2.2U M 50V 2.2U M 50V 0.1U Z 50V 47U M 50V 47U M 50V 47U M 50V 47U M 50V 0.1U M 50V 0.1U M 50V 0.1U Z 50V 0.01U K 50V 1U M 50V 1U M 50V 0.01U K 50V 0.01U K 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 1U M 50V 0.033U K 50V 0.033U K 50V 10U M 50V 10U M 50V 0.1U K 50V 1000P K 50V 1500P K 50V 1U M 50V 1U M 50V 1000U M 16V 1000U M 16V 0.1U K 25V 4.7U M 50V 4.7U M 50V 4.7U M 50V 4.7U M 50V 4.7U M 50V 4.7U M 50V 2200P K 50V 0.1U K 25V
-23-
C5DTH
Ref. No.
C3717 C3720 C3721 C3722 C3724 C3725 C3727 C3730 C3731 C3732 C3733 C3734 C3735 C420 C423 C424 C425 C432 C433 C434 C437 C441 C442 C462 C463 C464 C465 C466 C467 C468 C469 C470 C471 C486 C491 C510 C511 C514 C515 C517 C518 C520 C521 C524
Part No.
4040848806 4030490018 4040849209 4030510627 4040849209 4030510627 4040849209 4030510627 4031134119 4033423310 4040848806 4030490018 4032844314 4032789615 4032794312 4040848806 4030490018 4040848806 4030490018 4040848806 4030490018 4040806608 4033480610 4040774600 4033438215 4030834317 4033439410 4030757121 4030763122 4040876007 4030540713 4030666106 4032673211 4030790910 4040848707 4030486328 4031481411 4040848806 4030490018 4030660104 4032703720 4032558934 4030403721 4040848905 4030455829 4040848905 4030494224 4030698325 4040565208 4040849902 4032600722 4030765324 4040887300 4030427727 4032152211 4040875406 4030502810 4040886600 4030459867 4040849407 4030532134 4030729425 4030641212 4032769726 4040873709 4030533606 4030641212
Description
ELECT 1U M ELECT 1U M ELECT 4.7U M ELECT 4.7U M ELECT 4.7U M ELECT 4.7U M ELECT 4.7U M ELECT 4.7U M CERAMIC 2200P K CERAMIC 0.1U K ELECT 1U M ELECT 1U M CERAMIC 0.022U K CERAMIC 1U Z CERAMIC 0.33U K ELECT 1U M ELECT 1U M ELECT 1U M ELECT 1U M ELECT 1U M ELECT 1U M MT-POLYPRO 6800P H MT-POLYPRO 6800P H MT-POLYPRO 7800P H MT-POLYPRO 7800P H POLYPRO 0.022U J POLYPRO 0.02U J CERAMIC 1000P K CERAMIC 3900P K ELECT 47U M ELECT 47U M MT-POLYEST 0.47U J MT-POLYPRO 0.18U J MT-POLYPRO 0.15U J ELECT 0.47U M ELECT 0.47U M ELECT 220U M ELECT 1U M ELECT 1U M MT-POLYEST 2.2U K MT-POLYEST 0.39U K MT-COMPO 0.39U J ELECT 220U M ELECT 22U M ELECT 22U M ELECT 10U M ELECT 10U M CERAMIC 0.01U Z NP-ELECT 2.2U M NP-ELECT 2.2U M ELECT 33U M CERAMIC 680P K ELECT 22U M ELECT 22U M CERAMIC 0.01U K ELECT 22U M ELECT 22U M ELECT 2200U M ELECT 2200U M ELECT 220U M ELECT 220U M CERAMIC 3300P K POLYESTER 0.1U K POLYESTER 0.1U K ELECT 2200U M ELECT 2200U M POLYESTER 0.1U K 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 50V 50V 50V 16V 16V 50V 50V 50V 50V 50V 50V 1.5K 1.5K 1.5K 1.5K 400V 400V 500V 500V 35V 35V 250V 400V 400V 50V 50V 50V 50V 50V 100V 63V 50V 10V 25V 25V 50V 50V 50V 100V 100V 250V 500V 16V 16V 50V 50V 50V 25V 25V 35V 35V 50V 100V 100V 35V 35V 100V
Ref. No.
Part No.
4032769726 4040848905 4030494224 4030857316 4040712107 4040725602 4040607205 4040661702 4040936107 4040712107 4040725602 4040607205 4040661702 4040936107 4030766707 4032719622 4040445005 4030569734 4031789319 4030573137 4031818217 4032377941
Description
POLYESTER 0.1U K ELECT 10U M ELECT 10U M NP-ELECT 10U M MT-POLYEST 0.1U K MT-POLYEST 0.1U M MT-POLYEST 0.1U M MT-POLYEST 0.1U M MT-POLYEST 0.1U M MT-POLYEST 0.1U K MT-POLYEST 0.1U M MT-POLYEST 0.1U M MT-POLYEST 0.1U M MT-POLYEST 0.1U M CERAMIC 1000P K CERAMIC 1000P K CERAMIC 1000P K ELECT 220U M POLYESTER 0.01U J POLYESTER 0.01U J POLYESTER 0.1U K POLYESTER 0.1U K MT-COMPO 0.22U J CERAMIC 220P K CERAMIC 220P K MT-POLYEST 0.047U K CERAMIC 3300P K CERAMIC 3300P M CERAMIC 3300P M ELECT 1000U M ELECT 3.3U M ELECT 220U M ELECT 470U M NP-ELECT 33U M ELECT 3300U M CERAMIC 680P K CERAMIC 680P K CERAMIC 680P K CERAMIC 3300P K CERAMIC 470P K CERAMIC 470P K CERAMIC 470P K CERAMIC 470P K ELECT 0.22U M ELECT 0.22U M ELECT 220U M ELECT 220U M ELECT 470U M ELECT 470U M ELECT 470U M ELECT 470U M ELECT 2.2U M ELECT 47U M ELECT 47U M ELECT 47U M ELECT 47U M CERAMIC 15P J CERAMIC 27P J CERAMIC 0.01U K CERAMIC 0.047U Z ELECT 10U M ELECT 10U M CERAMIC 0.1U Z CERAMIC 0.01U K CERAMIC 0.01U K CERAMIC 0.1U Z CERAMIC 0.1U Z 100V 50V 50V 25V 250V 250V 250V 275V 275V 250V 250V 250V 275V 275V 1K 1K 1K 400V 50V 50V 50V 50V 50V 2K 2K 630V 250V 250V 400V 25V 25V 160V 35V 25V 25V 1K 1K 1K 1K 1K 1K 1K 1K 50V 50V 16V 16V 16V 16V 10V 10V 50V 35V 35V 16V 16V 50V 50V 50V 50V 16V 16V 25V 50V 50V 25V 50V
C527 C540 C601
!
!
C602
C608
C609 C611 C613 C614 C615 C617 C618 ! C629
C643 C644 C651 C652 C653 C654 C655
4033145103 4040734901 4040793304 4040715306 4031480424 4030461612 4040739005 4031482012 4030859805 4030468007
C656 C657 C658 C663 C664 C665 C681 C690 C691 C693 C801 C802 C803 C804 C805 C806 C811 C816 C823 C824
4032719820 4032719721 4032475023 4032691829 4032475023 4032691829 4040871606 4030481917 4040848004 4030430222 4040848301 4030441773 4040847601 4030414529 4040876007 4030540713 4040848202 4030439136 4031554214 4031572515 4032152211 4032247016 4040847700 4030418824 4031640214 4032152211 4032152211 4031640214 4033053517
-24-
C5DTH
Ref. No.
C829 C835 C836 C837 C851 C852 C853 C854 C856 C861 C862 C880 C892 C893 C894
Part No.
4031640214 4040848806 4030490018 4031573116 4031573116 4031573116 4031573116 4031573116 4040848905 4030494224 4031133815 4040848806 4030490018 4031640214 4031552210 4031573611 4031640214 4040849001 4030499823 4033335118
Description
CERAMIC ELECT ELECT CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC ELECT ELECT CERAMIC ELECT ELECT CERAMIC CERAMIC CERAMIC CERAMIC ELECT ELECT CERAMIC 0.1U 1U 1U 56P 56P 56P 56P 56P 10U 10U 1000P 1U 1U 0.1U 3300P 100P 0.1U 2.2U 2.2U 0.033U Z M M J J J J J M M K M M Z K J Z M M K 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 50V 50V 25V 50V 50V 50V
Ref. No.
R108 R1080 R1081 R1082 R1083 R109 R111 R112 R114 R115 R116 R121 R122 R124 R125 R130 R132 R140 R1401 R1402 R1403 R1405 R1406 R141 R1501 R1503 R1504 R1505 R1507 R1508 R176 R1901 R1902 R1903 R1904 R1905 R1906 R1907 R1911 R1912 R1913 R194 R195 R208 R210 R211 R212 R221 R222 R223 R224 R225 R226 R227 R228 R229 R230 R234 R235 R236 R237 R244 R245 R264 R265 R267 R271
Part No.
4010254636 4011054215 4011134412 4011134412 4011051610 4011058213 4011050514 4011056011 4011054017 4010272135 4011055816 4011056615 4011052815 4011050613 4010261337 4011057919 4011055212 4011057919 4011055212 4011055212 4011050613 4011050613 4011050613 4011055915 4011050514 4011057919 4011053416 4011055410 4011054215 4011056011 4011050613 4011053416 4011051115 4011056011 4011054611 4011052815 4011052013 4010246730 4010257439 4010257439 4010257439 4011055212 4011055212 4011057919 4011053713 4010251338 4010251338 4011050514 4011050514 4011050514 4011055311 4011055311 4011053416 4011055410 4010261634 4011056714 4010269333 4011055816 4011055816 4011055816 4011057414 4011055410 4011055410 4010260637 4011057919 4010260637 4011050415
Description
CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON CARBON CARBON CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON MT-GLAZE CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON MT-GLAZE CARBON MT-GLAZE 18K 33K 75 75 15K 68K 1K 5.6K 330 56 56 6.8K 2.2K 10K 27K 0.000 470 0.000 470 470 10K 10K 10K 560 1K 0.000 27K 47K 33K 5.6K 10K 27K 12K 5.6K 3.9K 2.2K 1.8K 100 220 220 220 470 470 0.000 3K 150 150 1K 1K 1K 4.7K 4.7K 27K 47K 270K 680K 47 56 56 56 8.2K 47K 47K 270 0.000 270 100 JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA ZA JA ZA JA JA JA JA JA JA JA ZA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA ZA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA ZA JA JA 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/6W 1/16W 1/16W 1/16W 1/16W 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/6W 1/6W 1/6W 1/6W 1/16W 1/16W 1/16W 1/16W 1/6W 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/6W 1/16W 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/6W 1/16W 1/6W 1/16W
RESISTOR
R005 R006 R007 R032 R033 R034 R035 R036 R037 R038 R1000 R1001 R1002 R1003 R1004 R1005 R101 R103 R1030 R1031 R1032 R1034 R1035 R106 R1060 R1061 R1062 R1063 R1064 R1065 R1066 R1067 R1068 R1069 R107 R1070 R1071 R1072 R1073 R1074 R1075 R1076 R1077 R1078 R1079 4010247440 4010077641 4010077641 4011053416 4010261337 4011057919 4010251635 4011057919 4010261337 4011051511 4011051412 4011052815 4011050712 4011052815 4011050712 4011054215 4011057919 4010618101 4011051412 4011052815 4011050712 4010257835 4011050712 4010246730 4010276638 4011056615 4011056615 4011055915 4011050712 4011055915 4011050712 4011054611 4011050514 4011056615 4010246730 4011056615 4011054611 4011050514 4011056615 4011051610 4011051412 4011051412 4011054215 4011056615 4011054215 CARBON CARBON CARBON MT-GLAZE CARBON MT-GLAZE CARBON MT-GLAZE CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE OXIDE-MT MT-GLAZE MT-GLAZE MT-GLAZE CARBON MT-GLAZE CARBON CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE CARBON MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE MT-GLAZE 10K 150 150 27K 27K 0.000 1.5K 0.000 27K 1.5K 150 2.2K 100K 2.2K 100K 33K 0.000 39K 150 2.2K 100K 2.2K 100K 100 75 6.8K 6.8K 560 100K 560 100K 3.9K 1K 6.8K 100 6.8K 3.9K 1K 6.8K 15K 150 150 33K 6.8K 33K JA JA JA JA JA ZA JA ZA JA JA JA JA JA JA JA JA ZA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA JA 1/6W 1/2W 1/2W 1/16W 1/6W 1/16W 1/6W 1/16W 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1W 1/16W 1/16W 1/16W 1/6W 1/16W 1/6W 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/6W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
-25-
C5DTH
Ref. No.
R272 R280 R281 R282 R283 R284 R285 R286 R287 R291 R352 R354 R355 R356 R357 R358 R359 R3731 R3732 R422 R423 R424 R426 R432 R433 R434 R435 R441 R442 R461 R462 R463 R464 R465 R466 R467 R469 R471 R472 R473 R474 R475 R477A R479 R480 R481 R488 R501 R510 R511 R512 R514 R515 R516 R518 R519 R522 R525 R527 R540 R602 R602C R611 R613 R614
Part No.
4011050415 4011050415 4011053416 4011054116 4011055311 4011054116 4010269333 4012039914 4011057919 4010681600 4010127059 40102582