Text preview for : 29FX6ALX CW62A.pdf part of LG TV 29FX6ALX CW62A 29FX6ALX Service manual ch. CW62A
Back to : 29FX6ALX CW62A.part1.rar | Home
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
COLOR TV
SERVICE MANUAL
CHASSIS : CW62A
MODEL : 29FX6ALX
MODEL : 29FX6ALX-ZG
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
Contents ...................................................................................................................2
Safety Precautions..............................................................................................3
Control Descriptions..........................................................................................4
Specifications........................................................................................................7
Adjustment Instructions .................................................................................8
Trouble Shooting ................................................................................................14
Printed circuit board.........................................................................................18
Block Diagram .....................................................................................................20
Exploded View....................................................................................................22
Exploded View Parts List .............................................................................23
Replacement Parts List .................................................................................24
SVC. Sheet..................................................................................................................
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Before returning the receiver to the customer,
An isolation Transformer should always be used during always perform an AC leakage current check on the exposed
the servicing of a receiver whose chassis is not isolated from metallic parts of the cabinet, such as antennas, terminals, etc.,
the AC power line. Use a transformer of adequate power rating to be sure the set is safe to operate without damage of
as this protects the technician from accidents resulting in electrical shock.
personal injury from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
It will also protect the receiver and it's components from being With the instrument AC plug removed from AC source,
damaged by accidental shorts of the circuitry that may be connect an electrical jumper across the two AC plug prongs.
inadvertently introduced during the service operation. Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
If any fuse (or Fusible Resistor) in this TV receiver is blown, ohm-meter lead in turn to each exposed metallic parts such as
replace it with the specified. antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
When replacing a high wattage resistor (Oxide Metal Film measured resistance should be between 1M and 5.2M.
Resistor, over 1W), keep the resistor 10mm away from PCB. When the exposed metal has no return path to the chassis the
reading must be infinite.
Keep wires away from high voltage or high temperature parts. An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube. Leakage Current Hot Check (See below Figure)
Do not lift the Picture tube by it's Neck. Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
X-RAY Radiation Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
Warning: and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
The source of X-RAY RADIATION in this TV receiver is the voltmeter with 1000 ohms/volt or more sensitivity.
High Voltage Section and the Picture Tube. Reverse plug the AC cord into the AC outlet and repeat AC
For continued X-RAY RADIATION protection, the voltage measurements for each exposed metallic part. Any
replacement tube must be the same type tube as specified in voltage measured must not exceed 0.75 volt RMS which is
the Replacement Parts List. corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
To determine the presence of high voltage, use an accurate
high impedance HV meter. Leakage Current Hot Check circuit
Adjust brightness, color, contrast controls to minimum. AC Volt-meter
Measure the high voltage.
The meter reading should indicate
23.5 ± 1.5KV: 14-19 inch, 26 ± 1.5KV: 19-21 inch,
29.0 ± 1.5KV: 25-29 inch, 30.0 ± 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service Good Earth Ground
and correction is required to prevent the possibility of such as WATER PIPE,
CONDUIT etc.
premature component failure. To Instrument's 0.15uF
exposed
METALLIC PARTS
1.5 Kohm/10W
DESCRIPTION OF CONTROLS
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
POWER MUTE
1 10
1 2 3 Remote control handset
4 5 6 Before you use the remote control handset, please install the bat-
2 teries. See the next page.
7 8 9
1. POWER
MENU 0 TV/AV switches the set on from standby or off to standby.
3 11
TV 2. NUMBER BUTTONS
switches the set on from standby or directly select a number.
PR- PR+
PR
3. MENU
selects a menu.
4 VOL OK VOL
4. D / E (Programme Up/Down)
PR selects a programme or a menu item.
SWAP UT switches the set on from standby.
INP
13 14 scans programmes automatically.
TEXT/MIX/ TIME/ REVEAL/ ? F / G (Volume Up/Down)
5 adjusts the volume.
SLEEPMODE/ M POSITION/ X STILL/ adjusts menu settings.
6 OK
PIP 9/4PIP i
7
SIZE/
accepts your selection or displays the current mode.
FAVOURITE EYE/ I/II/
8 12 5. TELETEXT BUTTONS (option)
9 These buttons are used for teletext.
For further details, see the `Teletext' section.
6. SLEEP
sets the sleep timer.
(With TELETEXT / PIP)
7. PIP BUTTONS (option)
PIP
switches the sub picture on or off.
PR +/-
selects a programme for the sub picture.
SWAP
PR
alternates between main and sub picture.
Q.VIE T
INPUT
W LIS selects the input mode for the sub picture.
SIZE
TEXT/MIX/ TIME/ REVEAL/ ? adjusts the sub picture size.
5 STILL
SLEEPMODE/ M UPDATE/ X HOLD/ freezes motion of the sub picture.
POSITION
SIZE/ INDEX/ i I/II/
relocates the sub picture in clockwise direction.
FAVOURITE EYE/
9/4 PIP
switches on or off the 9 or 4 sub pictures.
(With TELETEXT / Without PIP)
8. FAVOURITE
selects a favorite programme.
9. EYE/ (option)
*
switches the eye function on or off.
POWER MUTE
10
1
1 2 3
10. MUTE
switches the sound on or off. 4 5 6
2
11. TV/AV 7 8 9
selects TV or AV mode.
switches the set on from standby. MENU 0 TV/AV
exits the Teletext mode 3 11
12. I/II/
*
selects the language during dual language broadcast.
PR
selects the sound output (option).
VOL OK VOL
13. Q.VIEW (or YELLOW) 4
returns to the previously viewed programme.
PR
Q.VIE T
14. LIST (or BLUE) W LIS
13 14
displays the programme table.
9 EYE/ I/II/
SLEEP
6 12
: No function
* 8
FAVOURITE
COLOURED BUTTONS : These buttons are used for teletext (only
TELETEXT models) or programme edit.
(Without TELETEXT / PIP)
PR- PR+
PR
VOL OK VOL
PR
SWAP INPUT
SLEEP SIZE STILL
PIP POSITION 9/4PIP
7
FAVOURITE EYE/ I/II/
(With PIP / Without TELETEXT)
adjusts picture according to the surrounding conditions.
7. EYE (option)
Connect the audio/video out sockets of external equipment to these sockets.
6. AUDIO/VIDEO IN SOCKETS (AV IN3)
function.)
Note : Only use the supplied remote control handset. (When you use others, they'll be not able to
5. REMOTE CONTROL SENSOR
switches the set on from standby.
selects a programme or a menu item.
D / E (Programme Up/Down)
adjusts menu settings.
adjusts the volume.
F / G (Volume Down/Up)
accepts your selection or displays the current mode.
4. OK
selects a menu.
3. MENU
dims when the set is switched on.
illuminates brightly when the set is in standby mode.
2. POWER/STANDBY INDICATOR
switches the set on or off.
1. MAIN POWER (ON/OFF)
4 3 1
@@@ @
@@@@@@@@? @@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@? @@@@@@@@
@@?@@@@@? @@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@? @@@@@@@@
@@? g@@
g@
@@? g@@
@@? g@@
@@? g@@
@@? g@@
@@
@@ @@
@@ @@
@@
@@
@@ @@
@@ @@
@@
@@
@@ @@
@@
@@
@@
@@ @@
@@
@@
@@
@@ @@
@@ @@
@@
@@ @@
@@ @@
@@
@@ @@
@@ @@
@@
@@
@@ @@
@@ @@
@@
@@
@@
@@
@@
@@
@@
@@ @@
@@
@@
@@
@@ @@
@@ @@
@@
@@
@@ @@
@@
@@ ?h@@
@@ ?h@@
@@ ?h@@
@@ ?h@@
@@ ?h@@
@@ ?h@@
@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@?e@@@@@@@@
@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@?e@@@@@@@@
L/MONO AUDIO R
6 2
VIDEO
7
AV IN3
5
Side panel Front panel
SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.
V Scope V Test Condition
This specification can be applied to all the television related to 1) Temperature : 20 ± 5°C(CST : 40 ± 5°C)
CW62A Chassis. 2) Relative Humidity : 65 ± 10%
3) Power voltage : AC110-240V~, 50/60Hz
4) Follow each drawing or spec for spec and performance of
V Test and Inspection Method parts,based upon P/N of B.O.M
1) performance : Follow the Standard of LG TV test 5) Warm up TV set for more than 20min. before the
2) Standards of Etc. requirement measurement.
- Safety: IEC60065
- EMC: EN55020,EN55013
V General Specification
No Item Specification Remark
1 Receiving System PAL,SECAM BG EU/ Non EU
PAL/SECAM DK
PAL-I/I
NTSC M
NTSC 4.43(AV)
SECAM-L/L' OPTION
NTSC M/ PAL M/N
2 Available Channel VHF : E2 ~ E12 Non EU/ EU
UHF : E21 ~ E69
CATV : S1 ~ S20
HYPER : S21 ~ S41
VHF : 02 ~ 13 NTSC-M
UHF : 14 ~ 69
CATV : 02 ~ 13
3 Input Voltage AC 110-240V, 50/60Hz Non EU
AC 230V, 50/60Hz EU
4 Market EU,CIS, China, Asia, Africa
5 Screen Size Flat 29"
6 Tuning System FVS 100Program 200 PR(W/O TXT)
7 Operating Environment 1) Temp : 0 ~ 45 deg
2) Humidity : below 85%
8 Storage Environment 1) Temp : -20 ~ 60 deg
2) Humidity : below 85%
ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions are applied to all of the color TV, CW62A. As preparatory operations before
CPT Assembling
assembling CPT, wind cotton Tape for
protecting to CPT NECK and DY, CPT
2. Notes connection parts. At this moment, end
(1) Because this is not a hot chassis, it is not necessary to use of tape should be over-lapped and
an isolation transformer. However, the use of isolation wound in direct route to the NECK.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.But the Assembling DY to Fix the Magnet to the position as
adjustment can be changed by consideration of mass CPT shown picture below. Be careful not to
production. make CPT neck shadow while
(3) The adjustment must be performed in the circumstance of HEAT RUN adjusting DY.
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation. Degaussing
Convergence Magnet 6Pole 4 2
(4) The input AC voltage of the receiver must keep rating
voltage in adjusting. STC Pre-Adjustment
(5) The receiver must be operated for about 15 minutes prior ¢¸
¢¸
to the adjustment. PURITY Adjustment
15 ~ 20mm
(6) Signal: Received, the standard color signal.(65dB±1dB uV)
LG standard signal means the digital pattern DY Fixing Let the screen Standard condition.
(PAL_EU 05CH). Operate Heat-Run at least 15
SCREEN Voltage adj. minutes.
3. Focus adjustment W/B Fixing
Torque is to be 9-11 kg f.cm when
fixing DY.
(1) Receive the Cross-Hatch Pattern(Fig 1).
(2) Set the picture condition on "DYNAMIC(CLEAR)" mode. FOCUS not yet ADJ.
(3) Adjust the Focus volume of FBT for the best focus of (A) &
(B). STC not yet ADJ.
DYC not yet ADJ.
4.1. Color purity adjustment
(1) It makes CPT or CABINET enough to demagnetization.
(2) Receive the signal of red raster.
(3) Loosen fixed screw of DY and closely to CPT funnel part.
(4) Check the center of screen that PURITY MAGNET of CPT
by crossing adjustment. At this time, 4 & 6 pole magnet is
located to magnet of nothing.
(5) Move the DY to make equal red on whole screen and it
does not to make the DY by fixed screw after check a
simple color of Red/Green/Blue and white raster whether or
not it is a pollution of color.
(At this time, take care raster of screen and DY must fixing
in the condition which maintains a horizontality.)
(6) Check the TV set by move direction.
4. Purity & Convergence adjustment
4.2. Convergence adjustment
Adjustment should be operated when using the CPT(without
ITC from CPT manufacturing place) These adjustments can the best condition of focus after
This adjustment must be done in the order of the following finished purity adjustment.
flowchart.
(1) Receive the signal of cross hatch that BACK RASTER is
black.
(2) Adjust brightness and luminosity till dot appear 9 ~12.
(3) Open angle of the two tab of 4 pole MAGNET by isogonic
angle and accord with vertical line of red and blue color in
the middle of screen.
(4) Maintain as angle of (3) and rotate the tab to accord with
vertical line of Red and Blue color in the middle of screen.
(5) Open angle of the two tab of 6 pole magnet by isogonic 2. White balance IIC Parameter(Address)
angle and accord with vertical line of Red/Blue and Green.
Program Win31_wb TWB Win31_wb TWB Speed Delay
(6) Maintain as angle of (5) and rotate the tab to accord with
horizontal line. In case of twisted horizontal line,repeat Vcd Slave 8A Eeprom_Slave A0 1 30
adjustment of (3) ~ (5) remembering the movement of
Red/Green/Blue color. B(R)_Amp B(R)_Cut G_Amp G_Cut
(7) Move the DY to best condition of convergence and attach
Program Win31_wb TWB Win31_wb TWB Win31_wb TWB Win31_wb TWB
the CPT to a rubber-chock for fixing DY.
Sub Add 20 17 21 18
Start Bit 5 5 5 5
5. Screen voltage adjustment Stop Bit 0 0 0 0
(1) Receive the PAL or SECAM(NTSC) signal into RF mode Offset 0 0 2 2
(regardless of channel). Polarity 1 1 0 0
(2) If you press the "ADJ"button in LINE SVC mode(IN-START
EP_Rom_S 36 33 37 34
button),the LINE SVC mode changes to screen adjustment
mode. Speed/ Plus 2 2 2 2
(3) Turn the Screen Volume of FBT to change luminance of
White signal center as shown below.
(4) Press the ADJ button to exit SVC mode.
7. Deflection setting Data Adjustment
6. White balance adjustment 7.1 Adjustment preparation
(1) Tune the TV set to receive an Digital pattern(EU05CH).
NOTE : When adjusting white balance automatically,connect the (2) Deflection setting data adjustment is operate by SVC
adjustment JIG in SVC mode.(When pressing IN- communicator.
START,MUTE button on remote control for adjustment (3) Enter the deflection mode by selection SERVICE2 key on
orderly,it is changed to CPU OFF mode and screen is SERVICE MENU after enter the adjustment mode by
displayed to "CPU OFF".) pressing LINE SVC MODE(IN-START KEY).
(1) Receive 100% white pattern. (4) Use the CH D ,E key to select adjustment item.
(2) Adjust LOW Light status(4.5FL) of CR(R CUT), CB(B CUT) (5) Use the VOL F ,G key to increase/decrease data.
at CG(G CUT:75) : 60.
(3) Adjust HIGH Light status(35FL) of WR(R DRIVE), WB(B 7.2 Adjustment
DRIVE) at WG(G DRIVE:380) : 450.
(4) Repeat above step (2) and (3) for the best condition each - When adjusting a deflection,adjust N50Hz of PAL signal first and
status of High Light and Low Light. adjust a deflection data at N60Hz(NTSC), Z60Hz, N50Hz,
W50Hz, Z50Hz.
White Balance Color analyzer
- After finishing deflection adjustment, press the ENTER
Menu EU N-EU button to enter or exit SVC mode.
X 288 268
(1) H SHIFT
Y 295 273 Adjust so that the geometric horizontal center line is in
Color Temperature 9000oK 13000oK accord with horizontal center line of CPT.
(2) H PARALLEL
White Balance Initial Data Adjust vertical inclination of screen.
(3) H BOW
Menu Range DATA After finishing Cushion adjustment, adjust curved rate of
LOW LIGHT BLO-R(R CUT) 0 ~ 63 32 top & bottom corner to be equal.
(4) V LINEAR
BLO-G(G CUT) 0 ~ 63 32
Adjust the top & bottom size of inner circle to be equal.
BLO-B(B CUT) 0 ~ 63 FIX (5) V SCROLL
HIGH LIGHT RG(R DRIVE) 0 ~ 63 32 Adjust so that the geometric vertical center line is in accord
with vertical center line of CPT.
GG(G DRIVE) 0 ~ 63 32
BG (B DRIVE) 0 ~ 63 32
White Balance Initial Data
1. IC
Name Maker Algorithm
VCD IC
0 0 0 0
EP_ROM
(6) EW WIDTH
Adjust until the outmost left and right lattice of received
pattern is accord with 25% of other lattice width.
PIP H Position
8. Deflection setting initial data
PAL Digital pattern (EU05CH)
Deflection setting initial data (SERVICE 2)
* Fix : Don't change data
(7) EW PARABOLA
Adjust so that middle portion of the outermost left and right
29"
vertical line look like parallel with vertical lines of the CPT. Item Description Adjust
50Hz 60Hz
(8) EW UPCORNER & (9) EW LOCORNER H-SHIFT Horizontal shift 24 34 Adjust
After finished cushion adjustment, adjust vertical line of left- H PARALL Horizontal parallelogram 32 32 Recommend
top, right-top, left-bottom, right-bottom of screen to the best H BOW Bow 32 32 Recommend
straight line.
V LINEAR Vertical linearity 41 44 Recommend
CRNU6 V SCROLL Vertical scroll 30 30 Adjust
CRNU EW WIDTH EW width 57 57 Adjust
EW PARAB Parabola adj 18 15 Adjust
EW UPCOR Upper corner adj 49 45 Adjust
EP EW LOCOR Lower corner adj 53 50 Adjust
EW TRAPE Trapezoid adj 25 25 Adjust
V SLOPE Vertical slope 17 25 Recommend
CRNL
V AMPLIT Vertical amplitude 34 29 Recommend
CRNL6
SCORRECT S correction 35 30 Recommend
Cross-Hatch Pattern(E-7CH) V SHIFT Vertical shift 46 54 Recommend
V ZOOM Vertical zoom 25 25 Fix
(10) EW TRAPEZOID V SYNSLI Vertical slicing level 0 0 Fix
Adjust to make the length of top horizontal line same with it OVRVOLIN Over voltage input mode 0 0 Fix
of the bottom horizontal line.
VGUARD Vertical guard mode 0 0 Fix
(11) V SLOPE
(12) V AMPLITITUE
Adjust so that the circle of a digital circle pattern should be - After finishing deflection adjustment at PAL 50Hz, NTSC 60Hz
located interval of 6~7mm from the effective screen of the is applied deflection compensation value. But recheck condition
CPT. of adjustment at NTSC system and adjust deflection data if
(13) S CORRECTION necessary.
Adjust so that all distance between each lattice width of - Adjust PIP Position adjustment at only PAL 50Hz.
top/center/bottom are to be the same.
(14) V SHIFT
Adjust so that the geometric vertical center line is in accord
with vertical center line of CPT.
(15) V ZOOM (VERTICAL ZOOM)
(16) PIP_H(PIP H Position) adjustment - option
Adjust the H-Position by using VOL +/- key until PIP picture
is in contact with main picture.
9. Service adjustment data table OPTION 1, 2, 3, 4
ITEM Description
Picture setting service data1 (SERVICE 1)
OPTION1 INCH 29 S-Slim/ 29 N-Flat
ITEM DESCRIPTION 29" S-SLIM SYSTEM BG/DK/I/M, BG/DK/I/L
AGC ACG take over 25 200PR W/O TXT=>200PR, W/TXT=>100PR
RG Red Gain 32 TOP TOP=>Germany, Swiss, Austria, Italy
GG Green Gain 32 ACMS Auto channel memory system
BG Blue Gain 32 CH-AU China & Australia Frequency table
BLO-R Black level offset Red 32 BOOSTER
BLO-G Black level offset Green 32 OPTION2 SOUND RF stereo / AV stereo / Mono option
CDL Cathode Drive Level 5 PIP PIP option
L-DLY Luminance delay time 13 VOL CURVE High / Low volume curve
PEAK Peak white limiting 1 A2 STEREO Nicam check & FM stereo / Dual
SHOOT Pre overshoot ratio 1 I/II SAVE Dual sound setting save
HIDEVIAT (High deviation) Sound high deviation
Picture setting service data2 (SERVICE 3) OPTION3 SCART SCART option
DVD DVD option
ITEM DESCRIPTION 29" S-SLIM
XWAVE FM TX option
AM DEM G AM DEMODULATOR GAIN-AMLOW 0
EYE EYE option
FM DEM G FM DEMODULATOR GAIN-AGN 0
4KEY 4 Key option
ADC LEV ADC LEVEL(-16~5) - ADCLEV 0
TILT TILT option
DEC LEV DEC LEVEL(-16~5) - DECLEV 0
DEGAUSS (Degaussing) Degaussing option
MONO LEV MONO LEVEL(-16~5) - MONOLEV 0
OPTION4 OSD LANG Refer to the next page(table.8)
NICAMLEV NICAM LEVEL(-16~5) - NICLEV 0
TXT LANG Refer to the next page(table.8)
AUX1 VOL AUX1 VOL - AUX1VOLL(R) 0
REMOCON
AUX2 VOL AUX2 VOL - AUX2VOLL(R) 0
HOTEL HOTEL option
AUX3 VOL AUX3 VOL(SCART1 RF SOUND OUT) 0
TURBOSCH (Turbo search) Turbo search
FMWINDOW FM WINDOW FILTER (FMWS) 0
TURBOP/S (picture/sound) Turbo picture/ sound
BOOSTVAL BOOSTER 0
DCXO/A (DCXO auto adjust) DCXO auto adjust
MAXVOL MAX VOLUME 100
DCXO VAL DCXO 63
OSD & TEXT LANGUAGES
0 SOUTHEAST ASIA 0 ENGLISH
1 0 ENGLISH
1 INDONESIAN
2 MALAY
3 VIETNAMESE
4 THAI
2 RESERVED
3 RESERVED
4 RESERVED
5 RESERVED
6 RESERVED
7 RESERVED
1 EAST EU CYRILLIC TEXT 0 ENGLISH
1 EAST EU ALL 0 ENGLISH
1 GERMAN
2 RUMANIAN
3 POLISH
4 HUNGARIAN
5 CZECH
6 RUSSIAN
7 BULGARIAN
2 ENGLISH RUSSIAN 0 ENGLISH
1 RUSSIAN
3 RESERVED
4 RESERVED
5 RESERVED
6 RESERVED
7 RESERVED
3 WEST EU GREEK TEXT 0 ENGLISH
1 EU 7EA 0 ENGLISH
1 GERMAN
2 FRENCH
3 ITALIAN
4 SPANISH
5 DUTCH
6 PORTUGUESE
2 WEST EU ALL 0 ENGLISH
1 GERMAN
2 FRENCH
3 ITALIAN
4 SPANISH
5 DUTCH
6 SWEDISH
7 NORWEGIAN
8 DANISH
9 FINNISH
10 PORTUGUESE
11 GREEK
3 ENGLISH GREEK 0 ENGLISH
1 GREEK
4 RESERVED
5 RESERVED
6 RESERVED
7 RESERVED
3 ARAB TEXT 0 ENGLISH
1 ARABIC 0 ENGLISH
1 FRENCH