Text preview for : coffeemaker_®_.pdf part of Braun KF16 Service Manual coffeemaker - Pag. 6
Back to : coffeemaker_®_.pdf | Home
Service Documentation Braun Aromaster "2 in 1"
Market Release 11/97
KF 16
3076
3076
BINC Rev: 11/97 BAG Rev: 10/97
Service Documentation
Exploded Drawing 3076
3076 - 2
BINC Rev: 6/99 BAG Rev: 10/97
Service Documentation
Spare Parts List 3076 Part Description
Cover plate, white Container lid, white Shower head Tube Feed pipe Container, white Float Filling indicator, black printed Sealing Valve cpl. Angle tube Plastic insert Round plate Chassis, white Heating element cpl. Switch Mains lead Fastening spring Distance sleeve Nut Base plate Screw Filter cpl., white Carafe lid Carafe cpl. Rubber foot Space compensator Drop stop sealing Tea-sieve Sieve housing Water filter KWF-1 Water filter KFW-2
Pos. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 31
Part Number
3076640 3075008 4088922 4057151 3076016 3076001 3075019 3076020 3075010 3076960 4057011 3075900 4085850 3075002 3075603 3075040 4081851 4057278 4085022 0065007 3076923 0031128 3076912 3076010 3076797 3085007 3090132 4057134 3076201 3076630 3069791 3069792
3076 - 3
BINC Rev: 11/97 BAG Rev: 12/96
Service Documentation
Service Information 3076
Technical data Voltage: Nominal wattage (rating): Brewing time 6 Cups: Brewing temp. center of the ground coffee: Coffee Temp. direct after the brewing process: Keep-warm temperature after ½ hour and carafe ½ full at the keep warm plate: Fuse (not exchangeable): Thermostat (not exchangeable): Length of mains lead: Note The special screw (22), can only be removed with a screwdriver furnished with a special blade insert. These special blade inserts for screwdrivers can be ordered from the parts department. Because of approval-board requirements and reasons or safety, only this special screw must be used. Warning!!!! The non-insulated connecting wire between thermostat and heating element serves as a solder wire fuse. For this reason the wire should not be deformed, re-soldered or replaced by another type of connection. Disassembly / Assembly Remove filter and carafe. Turn-off switch and disconnect product from mains outlet. This product is easy to disassemble or to assemble. Only a few points must be observed: 1. 2. 3. 4. 5. 6. 7. The Base plate (21) is only attached with a Nut (20) and a Special screw (22). The location and the direction of the connecting wire and mains are shown in the wiring plan see sketch 3. The Cover plate (1) is fixed in three locations with the upper part of the Container (by snap action see sketch 1. The Chassis (14) is also fixed in three locations with the lower part of the Container (by snap action), see sketch 2. Insert Plastic insert (12) into direction of switch, while straightened part of insert is facing front. The Switch (16) will be inserted front the front into chassis (14). In order to remove switch, push both holding tabs towards inside. Pay attention to the proper connection and insertion of all tubes and at least one brewing cycle and safety checks upon completion of repair. 3076 - 4 120 V 750 Watt approx. 7 Minutes approx. 92 °C approx. 82 °C approx. 85 °C 295 °C 130 °C approx. 1.10 Meter
BINC Rev: 11/97 BAG Rev: 12/96
Service Documentation
Reference Drawing 3076
Sketch 1
Sketch 2
3076 - 5
BINC Rev: 11/97 BAG Rev: 12/96
Service Documentation
Reference Drawing 3076
Sketch 3
3076 - 6