Text preview for : BST-2K Tester Manual.pdf part of Pragathi Solutions BST-2k Diagnostic Tester
Back to : BST-2K Tester Manual.pdf | Home
Bangalore, INDIA
Contents_______________________________
1. Copyright Notice 2. Disclaimer 3. Etiquette guidelines 4. Package contents 5. Introduction 6. Specification 7. Quick Installation Guide 8. Parameters at a glance 9. Graphic User Interface Description 10. Warranty Guidelines 11. Contact Details
Bangalore, INDIA
1. Copyright Notice: Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owner's benefit, without intent to infringe.
2. Disclaimer: Specification and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be responsibility for any errors or omissions that may appear in this guide.
3. Etiquette guidelines:
Do's: Handle with care. See the Quick Installation Guide before Switching ON the Tester.
Don'ts: Don't connect the Adapter when diagnosis is in process with vehicle. Don't touch the Graphic LCD Screen Avoid using oily substance while handling Please do not remove any labels on the tester; this may void the warranty of this tester.
4. Package contents: 1. 2. 3. 4. 5. 6. 7. BST-2K Tester J1962M to DB9F, Cable (OBD Cable) RS232 Serial Cable 230 to 9 -Volt DC Adaptor Software CD containing Graphical User Interface Software User Manual Carrying pouch ____________
5. Introduction:
Software Features: · · · · · · · · · · · · Software Selectable options for EDC 15, EDC 16, EDC 17(12 & 24 Volt) Automatic Protocol (CAN / KWP) Selection Display Real Time data Read VIN , ECU Id Adjust ECU Parameters Test Actuator Read Error Codes Erase Error Codes Environmental Condition Freeze Frame Data Password Protection Saving option enabled for Diagnostic Trouble Codes & Env. Conditions
Hardware Features: · · · · · · · · · · · · · · · · · Handheld Diagnostic Tool EDC15 (12 Volt) & EDC16 (24Volt) combined unit Microcontroller based Unit. Memory inbuilt Online Data Storage CAN Communication enabled External Communication via K Line / CAN Diagnostic features implementation is based on ISO/DIS 14230.3 Power supply range 08 Volt 30 Volt Power Supply (12volt Linear) in built Diagnostic Tool doesn't require any external charging for backup Graphic LCD- 128x64 Pixels, Blue / Yellow-Green Backlight Touch pad J1962M to DB9F, OBD Cable Uploading the data to PC via serial port (RS-232 Cable) External noise protection enabled CRS diagnostics incorporated.
6. Specification:
Size Weight Body Color Diagnostic Socket PC Sync Version Language Power supply Product Type
23.7 x 13 x 4 cm. 400 Grams (Approx) Black J1962 M to DB-9 F (Type - OBD) Serial Port BST - 2.0.0.1 English Input- 220 volt / 50 Hz Output-9 volt DC, 500/1000 mA Compact
7. Quick Installation Guide: Step 1: Take J1962M to DB9F, Cable. J1962M connector connects to the J1962F that is located at the dashboard. DB9F connector connects to the BST-2K Tester.
Step 2: After the connection your system is ready to Diagnose. Step 3: To upload the data to the PC/Laptop, connect the Adapter connector to the socket. Step 4: To upload the data to the PC/Laptop, connect the RS232 Serial Cable to the PC/Laptop.
Step 5: Load the application exe from the CD Step 6: Run the Application.
Warning! Don't connect the Adapter when diagnosis is in process with vehicle.
8. Parameters at a glance: ACTUAL PARAMETERS
PARAMETER Set 1 Load Value Acc Pedal Postn Engine Speed Idling Speed Vehicle Speed Injection Quantity Fuel start Qty Fuel Limit Qty Governor Set Point Governor Variable PARAMETER Set 2 Inj. Actual Angle Inj. Nominal Angle Water Temperature Boost Air Temp Fuel Temperature Boost Air Pressure Battery Voltage Atmospheric Press Fuel Consumption PARAMETER Set 3 Timer Solenoid Pos Fuel Shut Off Sol Secondary speed Fuel Limiting Qty Max. Vehicle Speed deg.BTDC deg.BTDC deg.C deg.C deg.C mBar Volt mBar Iitre/hr UNIT % ON / OFF Rpm mg / stroke Km/hr % % Rpm Rpm Km/hr Mg/stroke Mg/stroke Mg/stroke Mvolt Mvolt UNIT UNIT
PARAMETER Set 4 Diagnostic Lamp Brake Switch Clutch Switch Adj. Inj. Begin Angle Adj. Eng Idle Speed Adj. Start Fuel Quantity PARAMETER Set 5
UNIT ON / OFF ON / OFF ON / OFF deg.BTDC Rpm mg / Stroke UNIT
Operating Counter Kilometer counter VIN ECU Id. Hardware Version Reprogramming Counter Date
Hrs KM ASCII ASCII ASCII BCD BCD
ADJUSTMENT PARAMETERS
Serial No 1 2 3 4 5 6
Description Max Vehicle Speed Adjustment Write Service Date Multiplicative Fuel Limiting Quantity Starting Fuel Correction Adjust Engine Idle Speed Read Service Date
Minimum 000
Maximum 120
Steps 1 ------0.01 1 1 -------
Unit Km/hr ------------Mg/stroke RPM -------
DD/MM/YYYY 0.9 1.01 00 -100 DD/MM/YYYY 20 100
Test Actuators
Serial No
Description
1 2 3
Timer Solenoid Position Fuel Shut Off Solenoid Diagnostic Lamp
Trouble Codes
Test
Error ID
106C
Error name
Needle Movement Sensor Error
Environmental Conditions
1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Secondary Speed 5.Battery Voltage 1. Engine Speed 2.Fuel Temperature 3.Present Injection Quantity 4. Governor Set Point 5. Governor Variable 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4. Atmospheric Pressure 5. Boost Pressure 1.Engine Speed 2.Present Injection Quantity
Unit
rpm °C Mg/stroke rpm Volt Rpm °C Mg/stroke mVolt mVolt Rpm °C Mg/stroke mBar mBar Rpm Mg/stroke
1099
Fuel Actuator Governor Feedback Input Signal Error
0235
Boost Pressure Sensor Error
0115
Water Temperature Sensor Error
3.Water Temperature 4. Air Temperature 5. Fuel Temperature 10B4 Fuel Actuator Governor Feedback Signal Error 1.Engine Speed 2. Fuel Temperature 3. Present Injection Quantity 4. Governor Set Point 5. Governor Variable 1.Secondary Speed 2.Water Temperature 3.Present Injection Quantity 4.Vehicle Speed 5.Analog Pedal Position
°C °C °C Rpm °C Mg/stroke mVolt mVolt Rpm °C Mg/stroke Km/h %
0725
Engine Speed Sensor Error
Trouble Codes Continued.......
Error ID
0120
Error name
Accelerator Pedal Sensor Error
Environmental Conditions
1. Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Vehicle Speed 5.Pedal Filtered 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Vehicle Speed 5.Analog Pedal Position 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Ratio Vehicle Speed to Eng Spd 5. Analog Pedal Position 1.Engine Speed 2.Water Temperature 3. Vehicle Speed 4.Analog Pedal Position 5. Battery Voltage 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Battery Voltage 5 Analog Pedal Position 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Fuel Temperature 5.Boost Preassure 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Engine Fault Lamp 5.Battery Voltage
Unit
rpm °C Mg/stroke Km/h % Rpm °C Mg/stroke Rpm % Rpm °C Mg/stroke No unit % Rpm °C Km/h % volt Rpm °C Mg/stroke Volt % Rpm °C Mg/stroke °C mBar Rpm °C Mg/stroke ON/OFF Volt
0220
Redundant Accelerator Pedal Sensor Error
0500
Vehicle Speed Sensor Error
0571
Brake Switch Signal Error
0180
Fuel Temperature Sensor Error
0095
Intake Manifold Input Signal Error
105A
Diagnostic Lamp Actuator Error
1063
Electric Shut Off Valve Error (ELAB)
0560
Battery Voltage Error
107E
Injection Begin Timing Governing
1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Engine Fault Lamp 5.Battery Voltage 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Battery Voltage 5.Analog Pedal Position 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Actual Injection Angle 5.Nominal Injection Angle
Rpm °C Mg/stroke On/OFF Volt Rpm °C Mg/stroke Volt % Rpm °C Mg/stroke °BTDC °BTDC
Error ID
0105
Error name
Atmospheric Pressure Sensor Error
Environmental Conditions
1.Engine Speed 2.Water Temperature 3. Present Injection Quantity 4. Boost Pressure 5. Battery Voltage 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Actual Injection Angle 5.Nominal Injection Angle 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Actual Injection Angle 5.Analog Pedal Position 1.Engine Speed 2.U Set Point for DSR(Digital Setting Governor) 3.Present Injection Quantity 4.Control Variable of the setting the governor 5.Fuel Temperature 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4. Battery Voltage 5.Analogue value accelerator sensor 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Engine Fault Lamp 5. Battery Voltage 1.Engine Speed 2.Water Temperature 3.Present Injection Quantity 4.Secondary Speed 5. Governor Set Point
Unit
Rpm °C Mg/stroke mBar Volt Rpm °C Mg/stroke °BTDC °BTDC Rpm °C Mg/stroke °BTDC % Rpm mVolt Mg/stroke mVolt °C Rpm °C Mg/stroke Volt % Rpm °C Mg/stroke ON/OFF Volt Rpm °C Mg/stroke Rpm mVolt
1087
Fuel Timing Actuator Error
1000
Micro controller Error
10A2
Fuel Quantity Actuator Error
1024
Main Relay Error
0110
Air Temperature Sensor Error
0175
Secondary speed Signal Error
9. Graphic User Interface (GUI) Description: Step 1: Download the Application "BST-2K Tester.exe" & "pdflib.dll" from the CD. Step 2: Connect the Serial Port to the Tester & PC. Step 3: Connect the Adaptor. I/P- 230Volt/50 Hz.& O/P- 09 Volt DC, Current 500 / 1000 mA
Step 4: Double click
icon.
Step 5: The BST-2K Tester.exe will open as follows:
Step 6: Select the COM PORT settings as per PC. Step 7: Click the "Connect Tester" Button Step 8: BST-2K Tester .exe software will read the Error code stored in the Tester and the Progress Bar will move on as shown below:
Step 9: The data transmission completed information will come at the LCD screen of the Handheld Tester. It'll display:
Done RESET to Begin
Step 10: Then click "Export to PDF" Button to transfer the entire content to your selected PDF file. Step11: After entire data will be transferred to the "Adobe Acrobat PDF" then press the "Disconnect Hardware" followed by "EXIT" button in the Graphic User Interface and "RESET the BST-2K Tester". 10. Warranty Guidelines:
The company provides 12 months repair service including parts and labour, however warranty for enclosure, skin cases, carrying straps, Stickers or any other accessories are not covered under warranty. 1. This warranty is confined to the first purchaser of the product only. 2. Repair or adjustments will be carried out through the Company. 3. In the event of repairs/replacement of any part/s of the unit, this warranty will thereafter continue and remain in force only for the unexpired period of the warranty. Moreover, the time taken for repair/replacement and in transit whether under the warranty or otherwise shall not be excluded from the warranty period. 4. The company reserves the right to retain any part/s or component/s replaced at its discretion in the event of a defect noticed in the equipment during the warranty period. 5. Any change of address shall be intimated to concerned service centre for continuation of warranty. Warranty for the unexpired period shall continue after the concerned service centre inspects the product and the product is found free from transit damage. 6. The warranty does not cover demonstration/ installation of the product purchased. 7. The warranty does not cover any accessories external to the system. 8. The company's obligation under this warranty shall be limited to repairing or providing replacement of part/s, which are found to be detective. 9. Any part/s of the system replaced by the company at it's discretion shall be with a functionally operative part. 10. The company is liable to provide the service support only for the models sold and marketed by Pragathi Solutions.
THIS WARRANTY IS NOT APPLICABLE IN ANY OF THE FOLLOWING CASES: 1. 2. 3. 4. The product is not purchased from Pragathi Solutions. The product is not used according to instructions given in the instruction manual. Defects caused by improper use as determined by the company personnel. Modification or alteration of any nature is made in the electrical circuitry/ or physical construction of the set. 5. Installation/ repair work is carried out by persons/agency other than authorized by the company. 6. Site (premises where the product is kept) conditions that do not confirm to the recommended operating conditions of the tester.
Contact Details
PRAGATHI SOLUTIONS #717, 6th Cross, 4th Main, New Tippasandra, HAL 3rd Stage , Bangalore 560075 Phone: +91- 80 32973388, +91- 80- 25293985 Cell: +91 - 9448030426
Email: [email protected] www.pragathisolutions.in
_______________________________________________________________________
Bangalore, INDIA