Text preview for : LM Service Manual Beko.pdf part of Beko chassis LM LM Service Manual_Circuit Diagram Compact Z1J190R-4_ Beko
Back to : LM_Beko.zip | Home
SERVICE MANUAL
LM CHASSIS
CONTENTS PAGE
Safety Instructions 3
Technical Specifications 4
Features 5
Inputs/Outputs Diagram 6
Remote Control 7
Set Apperance 8
Service Adjustments 9
Block Diagram 12
Power Supply Diagram 13
Data Sheet VCT4993 14
Data Sheet MST6181 16
Data Sheet MTV512 24
Data Sheet TVP5150A 26
Parts List 32
Circuit Diagram Attached
SAFETY PRECAUTIONS
GENERAL GUIDELINES
1. Always use the manufacturer's replacement safety
components. The critical safety components marked 5 High temperature & high humidity
with on the schematics diagrams should not be reduce the life-time.
by other substitutes. Other substitute may create the LCD is not proper to be used at high temperature
electrical shock , fire or other hazards. Take and high humidity. Please keep specified
attention to replace the spacers with the originals. temperature and humidity condition.
Furthermore where a short circuit has occurred ,
replace those components that indicate evidence of 6- Keep out of Corrosive Gas.
overheating.
Corrosive gas effect the polarizer and the circuit
2. After servicing , see that all the protective devices chemically and cause defects accordingly.
such as insulation barriers, insulation papers, shields
and isolation R-C combinations are correctly 7 - Electrostatic discharge can make
installed.
Damage
3. When the receiver is not being used for a long time
of period of time , unplug the power cord of the There are electro-static sensitive components such
Adaptor from the AC outlet. as CMOS in LCD Module. Please earth human
body when handle the LCD.In addition, please do
not touch the interface connector pin with bare.
Color TFT LCD Module is very sensitive
both electrically and physically.Users,
therefore, are requested to follow the 8- Do not operate for a long time under
the same pattern
"Guidance of handling color TFT LCD
Module"on the followings.
Operating LCD for a long time under the same
pattern can cause image persistence and can
1- Be careful not to make scratch on the damage it. Please follow following guidance.
polarizer. 1. Turn the power off when do not use.
Surface of polarizer is soft and can be physically 2. Change the pattern periodically.
damaged easily.
Please do not touch, push or rub polarizer surface
with materials over HB hardness.
2- Keep clean the surface.
Please wear rubber glove when touch the surface of
LCD screen. Please use soft and anti-static material
as cleaner.
3- Keep out of water.
Water on/in the LCD may cause electrical short or
corrosion. Please wipe out dry or water carefully.
4- Prevent swift Temperature &
Humidity change.
Instantaneous temperature and/or humidity change
can make dew or ice which cause nonconformance
such as malfunction.
Technical specifications chart
Picture tube 27" 16:9
size/type active matrix TFT
Sound outlet
2x7 W
power (10% THD)
Power
120 W
consumption
Stand-by Power 1W
consumption
General technical specifications
Power supply
AC: ............................................................................230V~50 Hz
Program memory: ...................................................100
RF Antenna input: ...................................................75 Ohm (Co-axial)
Loudspeaker impedance: ......................................4 Ohm
Sound systems:.......................................................Mono/Stereo/Nicam
Batteries: ..................................................................2xUM - 4, IEC R03 or AAA 1.5V
Received channels: .................................................VHF (Band I channel 2-4)
..................................................................................VHF (Band III channel 5-12)
..................................................................................UHF (Channel 21-69)
..................................................................................Cable TV (S1-S20/S21-S41)
Received broadcasting systems............................PAL BG
PAL SECAM BG
PA L S E C A M B G D K / D K '
PAL SECAM BG LL'
PAL I
Note: Your television has been manufactured in accordance with your country by selecting from
among the above mentioned broadcasting systems and this system cannot be changed by the user
except the case described below: In countries where BG/DK and BG/LL' broadcasts are done (BG
or DK / BG and LL'). For further information, see the settings part about your television.
4
Your Television
Features
· 27" TFT-LCD WXGA Panel
· Available for cable broadcasts
· 2x7 W Stereo sound
· 12 pages of teletext Feature
· PIP (Picture in Picture) Feature from AV
· Wide angle of vision
· Scart socket, AV Socket and external sound system connection
· S-VHS and Cinch inputs for S-Video connection
· PC connection
· Low energy consumption
· AVL
· ATS
· Programmable power off
· Graphic equalizer
· The feature of sharpness in Colour Transitions (CTI)
· Sharpness feature and picture resolution (LTI) in the black-white transitions
· A clear Picture made possible by the Digital Comb Filter
· On screen viewing of all settings, program numbers and all the processes
· Manual Fine Tuning
· 100 Program memory
· Infrared Remote Control equipped all the functions
· Child Lock
· Feature of viewing the NTSC broadcast to be entered via Scart
Easy performance of the processes via the advanced menu system. Ability to choose 26 different
menu languages.
· HDMI feature
5
S-VHS
V
AV-3
L
R
12
SCART 2
11
SCART1
V L R ANT IN L AUDIOR Y Pb Pr DVI-D HDMI PC- PC-DVI
AV-OUT COMPONENT
VIDEO INPUT IN AUDIO-IN
13
10 2 1 3 14
4 5 6 7 8 9
S-VHS V
15
16 SPDIF L ANT IN L AUDIO R Y Pb Pr HDMI PC-IN PC
AUDIO-OUT COMPONENT AUDIO-IN
AV3
17 VIDEO INPUT
L
18
R
19 20 21 22 23 24 25 26 27 28 29 30
1. Standby status indicator 16. Video input CINCH connector
2. Network power on/off button 17. Sound input CINCH connector (Left/L)
3. Remote control receiver 18. Sound input CINCH connector (Right/R)
4. Volume turn-down button 19. SPDIF Digital audio output
5. Volume enhancement button 20. Sound output (Left/L)
6. Menu Button 21. Sound output (Right/R)
7. Source selection 22. Antenna input
8. Program decrease button 23. Component sound input (L)
9. Program increase button 24. Component sound input (R)
10. Speaker 25. Component video input (Y)
11. Scart 1 26. Component video input (Pb)
12. Scart 2 27. Component video input (Pr)
13. Power supply input 28. HDMI
14. Headphones output 29. VGA (PC connection input)
15. S-VHS connector 30. PC sound input
Note:
· Please do not use the video RCA and S-Video connection simultaneously, in that case, these
two devices might influence the picture quality of one another.
· RGB offers the best picture quality over the Scart.
6
Remote Control
1. Picture Format selection button ( )
2. Temporary sound mute (Mute) button ( )
1 3. Equalizer selection button ( )
2 23 4. PIP Position selection button
PAT 24 5. PIP/PAP On-Off button
3 25 6. AV modes selection menu button
4 PIP SEL. PIP POS. PIP SIZE 7. Numeric buttons
5 26 8. ZOOM mode selection button
27
AV PC TV
9. Program down button ( )
6 28 10. Upward movement button( ) (Menus)
1 2 3 11. Volume turn-down button ( )
12. Left movement button ( ) (Menu)
7 4 5 6
13. Confirmation(OK) and Temporary picture
7 8 9 freeze button (Freeze) ( )
ZOOM
14. Info / Txt index page button ( )
8 0 SWAP
29
15. Downward movement button ( ) (Menus)
9 PR- PR+
30 16. Txt Question/Answer button (Reveal) ( )
10 17. Red teletext button ( )
11 VOL- VOL+ 31 18. Teletext page enlarge button (Double) ( )
19. Blue Teletext button ( )
OK/
12 FREEZE
32 20. Teletext / Mix selection buttons ( )
13 MENU 21. UPDATE Button/Teletext time ( )
14 i 33 22. Yellow teletext button ( )
15
16 ?
23. Stand-by On/Off button ( )
17
18 34
24. Picture Mode selection button ( )
25. PAT (Picture and Teletext) Mode
TEXT/
19 MIX 35 Power On-Off button
20 26. PIP size selection button
21 36 27. PC mode access button
22 28. PC mode access button
29. Final program selection button (SWAP)
( )
30. Program forward selection button ( )
31. Audio turn up button ( )
32. Right movement button ( ) (Menus)
33. MENU button
34. Txt Stop button (Hold) ( )
35. Green teletext button ( )
36. Sub page button (SUB PAGE) ( )
7
SET APPERANCE
INVERTOR(BUILT IN PANEL) MAIN CHASSIS POWER SUPPLY BOARD
8
LM SERVICE MODE
1. Activating the Service Menu
When the menu is on the screen press `9', `3', '0', '1' on the remote controller. This will activate
the service menu.
2. Service Mode Options
There are 6 submenus in this mode:
OPTIONS0, OPTIONS1, SOUND OPTIONS,IF SETTINGS, DIMMING, ADJUSTMENTS
2.1 OPTIONS0
STANDBY CUSTOME (Customer), FACTORY
TEXT Teletext Type : FAST (Fasttext), FAST TOP (Fastext and Toptext)
TEXT TBL AUTO : Selects the table according to the selected menu language
WEST: English-French-German-Turkish-Spanish-Italian-Finnish-Swedish
Norwegian, Danish
EAST : Polish-French-Hungarian-Czech-German-Sovenian-Italian-Romanian
GREE : WEST + Greek
CYRL : English-Russian-German-Czech-Estonian-Ukrainian-Letvian
ARAB : West + Arabian
FARS : West + Persian
HEBR : West + Hebrew
LANGUAGE A: English-German-French-Italian-Spanish-Portuguese-Greek-Turkish-Dutch-Swedish-
Danish-Norwegian-Finnish-Slovenian-Polish-Hungarian-Russian-Hebrew-Romanian-
Croatian-Czech-Slovak-Albanian-Bulgarian- Macedonian-Serbian
B: English-German-French-Italian-Spanish-Portuguese-Greek-Turkish-Dutch-Swedish-
Danish-Norwegian-Finnish-Slovenian-Polish-Hungarian-Russian-Romanian-Croatian-
Czech-Slovak-Albanian-Bulgarian- Macedonian-Arabic-Persian
PANEL Selects the software according to the panel name :
26 AU5, 32 AU3, 26 SS2, 32 SS3, 27 CH5, 32 CH2, 26 LP6,37 LP2, 26
QD2, 32 QD2
PIP NO (PIP via AV is not on), AV (PIP via AV is on)
PLUG PLAY ON (Demo mode), OFF
2.2 OPTIONS1
BLUEBACK ON, OFF
CTI Colour Transient Improvemnet Feature : ON, OFF, MENU
DNR Digital Noise Reduction : ON, OFF, MENU (selection via User Menu)
PROTECTION ON, OFF
PANORAMA AVAIL (On), NAVAIL (Off)
RC UNIT Remote Control Type: 43 Key, 45 key
PAT Picture and Text feature: AVAIL (On, Default), NAVAIL (Off)
HOTEL Simple Hotel TV feature: AVAIL (On), NAVAIL (Off)
HOTEL VOL Maximum sound level for Hotel Mode
9
2.3 SOUND OPTIONS
BG EUROPE, NEWZ (New Zelland) AUST (Australia), NAVAIL (no BG)
DK AVAIL, NAVAIL
L/L AVAIL, NAVAIL
DOLBY AVAIL, NAVAIL
BASS OPT NONE (bass is not activated), DYN (Dinamic bass is activated),
SUBW (Subwoofer feature is on)
HEADPHONE AVAIL, NAVAIL
CARRI MUTE MSP (for all markets except Turkey), MICRO (for Turkey)
2.4 IF SETTINGS
TUNER PS DA5, THOMSON, TEMIC, PS D44, ALPS, PHILIPS
VHF III UHF AGC adjustment is 5 for this frequancy band
VHF I AGC adjustment is 5 for this frequancy band
AGC Method AGC adjustment method: FIXED, SYNC&PW, SYNC, S&PW&PD (Default)
SECAM MTD Secam decoding method : OLD, NEW (default)
2.5 DIMMING
No adjustment will be made in this menu for service purposes. Default value is 0.
2.6 ADJUSTMENTS
No adjustment will be made in this menu for service purposes. Default values are given below:
VCTI BLE BLE MODE 3
BLE GAIN 2
BLE TILT 8
BLE STATIC 7
FAC LTI LTI CORING 0
LTI GAIN 0
SLL SUCARR SLLTHDV 6
SUBCARIIER 19
LUMA DELAY DLY PAL 7
DLY SECAM 10
DLY NTSC 9
SCART RGB BRI -14
CONT 47
CB SAT 50
CR SAT 50
TINT 0
RGAIN 34
GGAIN 33
BGAIN 35
10
MSTAR 6CR 5
6CG 5
6CB 8
6CC 0
6CM 3
6CY 2
6CF 5
SPECTRUM 1
ADJUST R GAIN 122
G GAIN 128
B GAIN 90
R OFFSET 125
G OFFSET 125
B OFFSET 126
SUBCON 58
SUB BRI 42
2.7 EEPROM EDIT
No adjustment will be made in this menu for service purposes.
11
Chassis LM Block Diagram
Analog Tuner1
TU300
IC335
Analog Tuner2 128MB DDR
TU302 IC329 IC328
Flash TxtRAM
IC336
Scart1 IC334
FRC 94XXA
LVDS
MST6181
Scart2 IC324
IC309
VCTi4993G
SVHS TVP150
Video Decoder
I2C
IR&Key IC311 IC321 IC301
MTV512 MAX9704
Monitor Audio Amp. HDMI VGA YPrPb
Controller
IC338
TDA7059
Headph. Amp
Basic
Optional
Power Supply Diagram
+12V
IC300 +3V3
T300
5V or 12V for LCD Panel
3V3 MST6181
IC302 VCTi
MST3383
2V5 DRAM
IC337 MST3383
MST6181
1V8 VCTi
MST6181
IC306
1V8 FRC
IC305
Only for FRC
12V Audio
T300 5V VCTi, Tuner
IC308
8V VCTi, Switches
IC307
13
VCT 49xyI, VCT 48xyI ADVANCE INFORMATION
Volume 1: General Description
General Description Submicron CMOS technology
Low-power standby mode
Release Note: This data sheet describes functions
and characteristics of the VCT 49xyI, VCT 48xyI Single 20.25 MHz reference crystal
version F1.
8-bit 8051 instruction set compatible CPU
Up to 256 kB on-chip program ROM
1. Introduction
WST, PDC, VPS, and WSS acquisition
The VCT 49xyI, VCT 48xyI is an IC family of high-qual- Closed Caption and V-chip acquisition
ity single-chip TV processors. Modular design and
deep-submicron technology allow the economic inte- Up to 10 pages on-chip teletext memory
gration of features in all classes of single-scan TV Multi-standard QSS IF processing with single SAW
sets. The VCT 49xyI, VCT 48xyI family is based on
functional blocks contained and approved in existing FM Radio and RDS with standard TV tuner
products like DRX 396xA, MSP 34x5G, VSP 94x7B, TV-sound demodulation:
DDP 3315C, and SDA 55xx. · all A2 standards
Each member of the family contains the entire IF, · all NICAM standards
audio, video, display, and deflection processing for 4:3 · BTSC/SAP with MNR (DBX optional)
and 16:9 50/60-Hz mono and stereo TV sets. The inte- · EIA-J
grated microcontroller is supported by a powerful OSD Baseband sound processing for loudspeaker chan-
generator with integrated Teletext & CC acquisition nel:
including on-chip page memory.
· volume and balance
· bass/treble or equalizer
· loudness and spatial effect (e.g. pseudo stereo)
Video & Sound IF
· Micronas AROUND (virtual Dolby optional)
DRX 396xA
· Micronas BASS and Subwoofer output
· further optional and licence requiring sound
enhancements as BBE, SRS Wow and Micronas
Audio Processing VOICE
MSP 34x5G
CVBS, S-VHS, YCbCr and RGB inputs
ITU656 input
Video Processing VCT 49xyI
4H adaptive comb filter (PAL/NTSC)
VSP 94x7B VCT 48xyI
multi-standard color decoder (PAL/NTSC/SECAM)
Macrovision Detection
Nonlinear horizontal scaling "panorama vision"
Display & Deflection
DDP 3315C Luma and chroma transient improvement (LTI, CTI)
Non-linear color space enhancement (NCE)
Dynamic black level expander (BLE)
Control, OSD, Text
SDA 55xx Selective Color Enhancer (SCE)
8/10 bit ITU656 output
Scan velocity modulation output
Fig. 11: Single-chip VCT 49xyI, VCT 48xyI
Soft start/stop of H-drive
Vertical angle and bow correction
1.1. Features
Average and peak beam current limiter
The VCT 49xyI, VCT 48xyI family offers a rich feature
set, covering the whole range of state-of-the-art 50/ Nonlinear and dynamic EHT compensation
60 Hz TV applications. Black switch off procedure (BSO)
PSSDIP88-1 package
PMQFP144-2 package
14
VCT 49xyI, VCT 48xyI ADVANCE INFORMATION
Volume 1: General Description
1.2. Chip Architecture
SPEAKER
SUBW
AOUT
TAGC
AIN
SIF
IFIN+ IF IF Sound Audio
IFIN- Frontend Processor Demodulator Processor 656 out
PROT
HOUT
HFLB
VERT
CVBS in Comb Color
Filter Decoder Display & EW
YCbCr in Video Panorama Video
Deflection SVM
RGB in Frontend Scaler Backend
Component Processor RGB out
CVBS out Interface RGB in
656 in SENSE
RSW
I2C Master/
Bus Display I2C
Slicer Slave
Arbiter Generator
Timer
CRT
PWM RESETQ
24kB CPU Reset & Test
ADC
Char ROM 8051 Logic TEST
UART
Watchdog
RTC
256kB Memory Clock XTAL1
20kB XRAM
Prog ROM Interface I/O-Ports Generator XTAL2
ADB, DB, PSENQ, Pxy
PSWEQ, WRQ, RDQ
Fig. 12: Block diagram of the VCT 49xyI, VCT 48xyI
15
MST6181LDA
SXGA/WXGA LCD Multi-Function Monitor Controller with Dual LVDS Transmitter
Product Brief Version 1.0
FEATURES
Y Input supports up to UXGA & 1080P n Auto-Configuration/Auto-Detection
Y Panel supports up to SXGA/WXGA Y Auto input signal format (SOG, Composite,
Y Integrated 8-bit triple-ADC/PLL Separated HSYNC, VSYNC, and DE), and input
Y Integrated DVI/HDCP/HDMI compliant receiver mode (all VESA & IBM modes w/ resolution
Y RGB/YUV 444 and YUV422 digital video input and polarity) detection
ports Y Auto-tuning function including phasing,
Y Dual high-quality scaling engines positioning, offset, gain, and jitter detection
Y Built-in 3-D video de-interlacer Y Sync Detection for H/V Sync
Y Video-over-graphic PIP n Dual High-Performance Scaling Engine
Y Video-by-graphic split screen Y Fully Programmable shrink/zoom capabilities
Y MStarACE-2 picture/color processing engine Y Nonlinear video scaling supports various
Y Embedded On-screen display controller (OSD) modes including Panorama
engine Y Flexible independent control of sharpness for
Y Digital audio I/O & sync processor TV and graphic windows
Y Built-in dual-link LVDS transmitter n Video Processing & Conversion
Y 5 Volt tolerant inputs Y 3-D motion adaptive video de-interlacer with
Y Low EMI and power saving features upgraded edge-oriented adaptive algorithm for
Y Supports PWM & GPO controls smooth low-angle edges
Y 256-pin LQFP Y Automatic 3:2 pull-down & 2:2 pull-down
n Analog RGB Compliant Input Ports detection and recovery
Y Dual analog ports support up to 165Mhz Y PIP with programmable size and location,
Y Supports PC RGB input up to UXGA@60Hz supports multi-video applications
Y Supports HDTV RGB/YPbPr/YCbCr up to 1080P Y Video-over-graphic overlay
Y On-chip high-performance PLLs Y Video-by-graphic split screen
Y Supports Composite Sync and SOG Y Frame rate conversion for both main window
(Sync-on-Green) separator and sub window
Y Automatic color calibration Y MStar 2nd Generation Advanced Color Engine
n DVI/HDCP/HDMI Compliant Input Port (MStarACE-2) automatic picture enhancement
Y Operates up to 165 MHz (up to UXGA @60Hz) gives:
Y Single link on-chip DVI 1.0 compliant receiver Y Brilliant and fresh color
Y High-bandwidth Digital Content Protection Y Intensified contrast and details
(HDCP) 1.1 compliant receiver Y Vivid skin tone
Y High Definition Multimedia Interface (HDMI) Y Sharp edge
1.0 compliant receiver with I2S and S/PDIF Y Enhanced depth of field perception
digital audio outputs Y Accurate and independent color control
Y Long-cable tolerant robust receiving Y Independent picture control for main and sub
n Video Input Port windows
Y One RGB/YUV 4:4:4 24-bit and one 4:2:2 Y sRGB compliance allows end-user to
ITU-R BT.656 8-bit digital video input ports experience the same colors as viewed on CRTs
Y 24-bit port supports 8/16-bit YUV 4:2:2 or and other displays
24-bit RGB/YUV 4:4:4 interlaced/ progressive Y Programmable 10-bit RGB gamma CLUT
video input up to 1080i/720P Y 3-D video noise reduction
Version 1.0 - 16 - 1/12/2006
Copyright © 2006 MStar Semiconductor, Inc. All rights reserved.
MST6181LDA
SXGA/WXGA LCD Multi-Function Monitor Controller with Dual LVDS Transmitter
Product Brief Version 1.0
n On-Screen OSD Controller Y Supports 2 data output formats: Thine & TI
Y 16/256 color palette data mappings
Y 256/512 1-bit/pixel font Y Compatible with TIA/EIA
Y 128/256/512 4-bit/pixel font Y With 6/8 bits options
Y Supports texture function Y Reduced swing for LVDS for low EMI
Y Supports 4K attribute/code Y Supports flexible spread spectrum frequency
Y Horizontal and vertical stretch of OSD menus with 360Hz~11.8MHz and up to 25%
Y Supports button function modulation
Y Pattern generator for production test n External Connection/Component
Y Supports OSD MUX and alpha blending Y Support 8051 parallel MCU bus
capability Y Supports 4-wire double-data-rate direct MCU
Y Supports blinking and scrolling for closed bus
caption applications Y 32-bit data bus for external frame buffer (SDR
n LVDS Panel Interface or DDR DRAM)
Y Supports dual link up to 135MHz dot clock for Y All system clocks synthesized from a single
SXGA external clock
GENERAL DESCRIPTION
The MST6181LDA is a high performance and fully integrated graphics processing IC solution for multi-function
LCD monitor/TV with resolutions up to SXGA/WXGA. It is configured with an integrated triple-ADC/PLL, an
integrated DVI/HDCP/HDMI receiver, a video de-interlacer, two high quality scaling engines, an on-screen
display controller, and a built-in output clock generator. By use of external frame buffer, PIP is provided for
multimedia applications. It supports de-interlaced full-screen video, video-on-graphic overlay, split screen,
frame rate conversion, and aspect ratio conversion for various video sources. To further reduce system costs,
the MST6181LDA also integrates intelligent power management control capability for green-mode requirements
and spread-spectrum support for EMI management.
Version 1.0 - 17 - 1/12/2006
Copyright © 2006 MStar Semiconductor, Inc. All rights reserved.
MST6181LDA
SXGA/WXGA LCD Multi-Function Monitor Controller with Dual LVDS Transmitter
Product Brief Version 1.0
PIN DIAGRAM (MST6181LDA)
VI_DATA[31]
VI_DATA[30]
VI_DATA[29]
VI_DATA[28]
VI_DATA[27]
VI_DATA[26]
VI_DATA[25]
VI_DATA[24]
AVDD_MPLL
BUSTYPE
LVACKM
AUMUTE
LVACKP
LVBCKM
LVBCKP
SPDIFO
VI_CKB
LVA1M
LVA2M
AUMCK
LVA1P
LVA2P
LVA0M
LVA3M
LVB0M
LVB1M
LVB2M
LVB3M
AIMCK
AUSCK
LVA0P
LVA3P
PWM1
PWM0
LVB0P
LVB1P
LVB2P
LVB3P
AISCK
AUWS
VDDC
VDDP
VDDC
VDDC
XOUT
VDDP
VDDP
AIWS
AUSD
GND
AISD
GND
GND
GND
GND
GND
GND
XIN
NC
NC
NC
NC
NC
NC
256
255
254
253
252
251
250
249
248
247
246
245
244
243
242
241
240
239
238
237
236
235
234
233
232
231
230
229
228
227
226
225
224
223
222
221
220
219
218
217
216
215
214
213
212
211
210
209
208
207
206
205
204
203
202
201
200
199
198
197
196
195
194
193
GND 1 192 BYPASS
GND 2 191 NC
DVI_R+ 3 190 PWM5
DVI_R-
Pin 1
4 189 PWM4
GND 5 188 PWM3
DVI_G+ 6 187 NC
DVI_G- 7 186 GPO[6]
AVDD_DVI 8 185 GPO[5]
DVI_B+ 9 184 GPO[4]
DVI_B- 10 183 VDDP
GND 11 182 GND
DVI_CK+ 12 181 GND
DVI_CK- 13 180 VDDC
AVDD_DVI 14 179 GPO[3]
REXT 15 178 GPO[2]
AVDD_PLL 16 177 GPO[1]
GND 17 176 GPO[0]
DDCD_DA 18 175 GND
DDCD_CK 19 174 VDDM
GND 20 173 DQS[0]
AVDD_ADC 21 172 MDATA[0]
HSYNC1 22