Text preview for : LG MZ-42PZ44.pdf part of LG MZ-42PZ44 S.M.
Back to : LG MZ-42PZ44.part1.rar | Home
website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html
PLASMA MONITOR/TUNER SERVICE MANUAL
CHASSIS : RF-03FA
MODEL : MT-42PZ44/S/45M/V/VB/47M/V MODEL : MZ-42PZ44/S/45V/VS MODEL : RT-42PZ45V MODEL : RT/RZ-BA50
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
SAFETY PRECAUTIONS ...................................................................................3 DESCRIPTION OF CONTROLS ........................................................................ 4 SPECIFICATIONS .............................................................................................. 8 ADJUSTMENT INSTRUCTIONS ......................................................................17 BLOCK DIAGRAM .............................................................................................19 ASSEMBLY METHOD........................................................................................20 PRINTED CIRCUIT BOARD ..............................................................................25 EXPLODED VIEW ..............................................................................................30 EXPLODED VIEW PARTS LIST ........................................................................31 REPLACEMENT PARTS LIST...........................................................................32 SCHEMATIC DIAGRAM ........................................................................................
- 2 -
SAFETY PRECAUTIONS
IMPORT ANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this monitor is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts. Due to high vacuum and large surface area of picture tube, extreme care should be used in handling the Picture Tube. Do not lift the Picture tube by it's Neck.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
Leakage Current Hot Check circuit
AC Volt-meter
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.
To Instrument's exposed METALLIC PARTS
Good Earth Ground such as WATER PIPE, CONDUIT etc.
0.15uF
1.5 Kohm/10W
- 3 -
DESCRIPTION OF CONTROLS
ON/OFF
INPUT SELECT
MENU
VOL.
Main Power Button
INPUT SELECT Button Remote Control Sensor
D,E
Buttons
VOLUME (F,G) Buttons MENU Button Power Standby Indicator Illuminates red in standby mode, Illuminates green when the Monitor is turned on
( )R( )
( )L ( )
RS-232C INPUT
(CONTROL/SERVICE)
R AUDIO L
Y
PB
PR
EXTERNAL SPEAKER
DVI INPUT
RGB INPUT
AUDIO INPUT
RGB OUTPUT
EXPANDED
INPUT
REMOTE CONTROL S-VIDEO VIDEO INPUT
R AUDIO L (MONO)
AUDIO INPUT
COMPONENT INPUT
AUDIO INPUT
AC INPUT
RS-232C INPUT
DVI INPUT RGB INPUT
AUDIO INPUT RGB OUTPUT EXPANDED INPUT
AUDIO INPUT
S-VIDEO INPUT COMPONENT INPUT
AUDIO INPUT VIDEO INPUT
Connection to PC
Connection to AV equipment
Note: The connection cables shown above to the right are not included with the Monitor. A D-sub 15-pin cable and a DVI cable are provided to connect the Monitor to a PC.
- 4 -
RT-BA50
DC IN (DC 12V) ANT IN +75 AV(EXPANDED) INPUT AV OUTPUT REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
EXPANDED OUTPUT
DC IN (DC 12V)
AV(EXPAND AV OUT- REMOTE ED) INPUT PUT CONTROL
ANTENA INPUT RZ-BA50
REMOTE CONTROL DC IN (DC 12V) ANT IN +75 AV1(EXPANDED) AV2(EXPANDED) EXPANDED OUTPUT
AV1/2 (EXPANDED) INPUT
RCA Type
( )R( )
( )L ( )
RS-232C INPUT
(CONTROL/SERVICE)
R AUDIO L
Y
PB
PR
EXTERNAL SPEAKER
DVI INPUT
RGB INPUT
AUDIO INPUT
RGB OUTPUT
EXPANDED
INPUT
REMOTE CONTROL S-VIDEO VIDEO INPUT
R AUDIO L (MONO)
AUDIO INPUT
COMPONENT INPUT
AUDIO INPUT
AC INPUT
EXTERNAL SPEAKER (8 ohm output)
DVI INPUT/RGB INPUT/AUDIO INPUT / RGB OUTPUT RS-232C INPUT EXPANDED INPUT (CONTROL/SE RVICE) PORT
AUDIO INPUT/COMPONENT INPUT / REMOTE CONTROL / S-VIDEO/VIDEO INPUT/AUDIO INPUT POWER CORD SOCKET
Scart Type
( )R( )
( )L ( )
RS-232C INPUT
(CONTROL/SERVICE)
EXTERNAL SPEAKER
DVI INPUT
RGB INPUT
AUDIO INPUT
RGB OUTPUT
EXPANDED
INPUT
AC INPUT
EURO SCART SOCKET
- 5 -
- This function works only when the PDP Tuner is installed on the LG plasma display monitor.
Installing PDP Tuner on the Monitor
1. Turn the monitor off and disconnect the mains plug. 2. Carefully place the Monitor screen side down on a cushioned surface that will protect the monitor screen from damage. 3. Mount the PDP Tuner gently into the correct position. Make sure it is inserted correctly. 4. Tighten the screws. 5. Connent the EXPANDED OUTPUT socket the on the PDP Tuner to the EXPANDED INPUT socket on the Monitor. 6. Turn the monitor on.
Antenna Connection
- Connect the Plasma Display with various external equipments after connecting the Monitor with the PDP Tuner and the Speakers. 1. Connect the RF out socket of the VCR to the aerial socket on the back of the monitor. 2. Connect the aerial cable to the RF aerial in socket of the VCR. 3. Store the VCR channel on the programme number 0 using the `Manual programme tuning' section. 4. Select the programme number where the VCR channel is stored. 5. Press the PLAY button on the VCR.
DC IN (DC 12V)
ANT IN +75
AV(EXPANDED) INPUT
AV OUTPUT
REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
< Back panel of the PDP Tuner >
VCR
Monitor Out Setup
The PDP Tuner has a special signal output capability which allows you to hook up a second TV or monitor. Just connect the second TV or monitor to the AV OUTPUT socket on the PDP Tuner. See the Operating Manual of the second TV or monitor for further details regarding that device's input settings.
< Back panel of the PDP Tuner >
DC IN (DC 12V) ANT IN +75 AV(EXPANDED) INPUT AV OUTPUT REMOTE CONTROL
VIDEO
or
ANT OUT
< Back panel of the PDP Tuner >
REMOTE CONTROL DC IN (DC 12V) ANT IN +75
ANT OUT
AV1(EXPANDED) AV2(EXPANDED) EXPANDED OUTPUT
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
ANT IN
S-VIDEO
OUT (R) AUDIO (L) IN VIDEO
ANT IN
S-VIDEO
OUT (R) AUDIO (L) IN VIDEO
RZ-BA50
Input Mode Normal TV, AV, AV1(EXP.) or S-Video Main RGB, DVI or Picture Component Sub TV or AV1(EXP.) Picture Main Picture TV, AV, AV1(EXP.) or S-Video Monitor OUT (AV2(EXP.)) Main Picture Normal
RT-BA50
Input Mode TV, AV(EXP.), AV or SVideo Main Picture Sub Picture Main Picture RGB, DVI or Component TV, AV(EXP.) TV, AV(EXP.), AV or S-Video Main Picture Monitor OUT (AV(EXP.)) Main Picture
Sub Picture PIP/DW Main Picture
Sub Picture
PIP/DW
- 6 -
Watching VCR
- When connecting the Monitor to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white, Audio (R) -red). - Connect the VIDEO INPUT socket (yellow) with the BNC-RCA adaptor to the VIDEO INPUT on the Monitor. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the Monitor. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the monitor. - Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If a 4:3 picture format is used; the fixed image may remain visible on the screen. - To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor. Watching TV programmes - Turn the Plasma Display on and select the programme you want. Watching VCR 1. Use the INPUT SELECT button on the remote control to select AV (AV1 or AV2) or AV(EXP.) (AV1(EXP.) or AV2(EXP.)). - If both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-VIDEO can be received. - If connected to S-VIDEO, select the S-Video external input source. 2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owner's manual)
DC IN (DC 12V)
ANT IN +75
AV(EXPANDED) INPUT
AV OUTPUT
REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
< Back panel of the PDP Tuner >
S-VIDEO
OUT (R) AUDIO (L) IN VIDEO
< VCR >
Watching Cable TV
- After subscribing for a local cable TV station and installing a converter you can watch cable TV. - For further information of cable TV, contact the local cable TV station. In using connection 1 1. Select programme number in programme switch of cable box. 2. Match the Plasma Display programme with selected programme of cable box. 3. Select your desired programme with the remote control for cable box. In using connection 2 1. Use the INPUT SELECT button on the remote control and select AV (AV1 or AV2) or AV(EXP.) (AV1(EXP.) or AV2(EXP.)). 2. Tune to cable service provided channels using the cable box.
RF Cable
DC IN (DC 12V)
ANT IN +75
AV(EXPANDED) INPUT
AV OUTPUT
REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
< Back panel of the PDP Tuner > 1 For cable TV 2
(R) AUDIO (L) TV VCR
VIDEO TV
(R) AUDIO (L)
VIDEO
RF
Cable
VCR
< Cable Box >
- 7 -
Watching external AV source
- When connecting the monitor to an external source, match the colours of AUDIO/VIDEO input jacks on the monitor with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the monitor. How to use 1. Use the INPUT SELECT button on the remote control to select AV (AV1 or AV2) or AV(EXP.) (AV1(EXP.) or AV2(EXP.)). 2. Operate the corresponding external equipment. See external equipment operating guide.
DC IN (DC 12V) ANT IN +75 AV(EXPANDED) INPUT AV OUTPUT REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
< Back panel of the PDP Tuner >
Camcorder
R
AUDIO
L
VIDEO
Video game set
< Back of the external equipment >
Watching DVD
< Back panel of the PDP Tuner >
DC IN (DC 12V) ANT IN +75 AV(EXPANDED) INPUT AV OUTPUT REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
How to connect Connect DVD video inputs to Y, PB, PR of COMPONENT INPUT and audio inputs to Audio sockets of AUDIO INPUT. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set. How to use 1. Turn on the DVD player, and insert a DVD. 2. Use INPUT SELECT button on the remote control to select Component or (AV1 or AV2) or (AV1(EXP.) or AV2(EXP.)). Refer to the DVD player's manual for operating instructions.
R AUDIO L
Y
PB
PR
RGB OUTPUT
EXPANDED
INPUT
REMOTE CONTROL S-VIDEO
R AUDIO L (MONO)
AUDIO INPUT
COMPONENT INPUT
VIDEO INPUT
AUDIO INPUT
AC INPUT
· Component Input ports You can get better picture quality if you connect DVD player with component input ports as below. Component ports of the Monitor Y Y Y Y Y PB PR
< Back panel of the Monitor >
or
(R) AUDIO (L)
B R
(R) AUDIO (L)
S-VIDEO
Video output ports of DVD player
< Back panel of a DVD player >
Pr Pb B-Y R-Y Cb Cr PB PR
Watching DTV (option) - To watch digitally broadcast programs, purchase and connect a digital set-top box. How to connect
1. Use the monitor's COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. < Back panel of
< Back panel of the PDP Tuner >
DC IN (DC 12V) ANT IN +75 AV(EXPANDED) INPUT AV OUTPUT REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
How to use
1. Turn on the digital set-top box. (Refer to the owner's manual for the digital set-top box.) 2. Use INPUT SELECT on the remote control to select Component, RGB or DVI. · DTV Input signal Terminal Component RGB (DTV) Mode 576p(50Hz) 1080i(50Hz) 1152i(50Hz) o o o o o o
the Monitor >
R AUDIO L
Y
PB
PR
VI INPUT
RGB INPUT
AUDIO INPUT
RGB OUTPUT
EXPANDED
INPUT
REMOTE CONTROL S-VIDEO VIDEO INPUT
R AUDIO L (MO
AUDIO INPUT
COMPONENT INPUT
AUDIO INPUT
or
(R) AUDIO (L) DTV OUTPUT (R) AUDIO (L) Y PB PR
< Digital Set-top box >
- 8 -
Connecting PC
- To enjoy vivid picture and sound, connect a PC to the Monitor. - Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. - Connect PC to the RGB INPUT or DVI INPUT port of the Monitor; change the resolution output of PC accordingly. - There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card. - The synchronization input form for Horizontal and Vertical frequencies is separate. Setup Instructions to Connect a PC to your Monitor - We recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality. - If the resolution of PC is over UXGA, there will be no picture on the Monitor. - Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the Monitor or the signal cable from the DVI output port of the PC to the DVI INPUT port on the Monitor. - Connect the audio cable from the PC to the Audio input on the Monitor. (Audio cables are not included with the Monitor). - If using a sound card, adjust PC sound as required. - This monitor apply a VESA Plug and Play Solution. The monitor provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically to use this monitor. - DDC protocol is preset for RGB (Analog RGB), DVI (DVI, Digital RGB) mode. - If required, adjust the monitor settings for Plug and Play functionally. - If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI INPUT to display the PC on the monitor. If graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or DVI; (the other mode is set to Plug and Play automatically by the monitor.) - DOS mode may not work depending on video card if using a DVI-I cable. - To see a normal picture, match the VGA mode and DVI signal (640x480, 848x480, 852x480). (See page 28)
< Back panel of the PDP Tuner >
DC IN (DC 12V) ANT IN +75 AV(EXPANDED) INPUT AV OUTPUT REMOTE CONTROL
VIDEO
EXPANDED OUTPUT
R AUDIO L (MONO) VIDEO
R AUDIO L
PC Setup 1. Turn on the PC and apply power to the Monitor. 2. Turn on the display by pressing the POWER button on the Monitor's remote control. 3. Use the INPUT SELECT button on the remote control to select the RGB or DVI input source. 4. Set the resolution output of the PC to SXGA or under (1280 x 1024, 60Hz).
( )R( )
( )L ( )
RS-232C INPUT
(CONTROL/SERVICE)
EXTERNAL SPEAKER
DVI INPUT
RGB INPUT
AUDIO INPUT
RGB OUTPUT
EXPANDED
INPUT
AU
< Back panel of the Monitor >
- 9 -
- When using the remote control aim it at the remote control sensor of the Monitor. - There's maybe a defect in consecutive operation of remote control in specified brightness according to this monitor feature. - This remote control handset is the one offered when purchasing a LG plasma display monitor.
POWER Switches the Monitor on from standby or off to standby.
POWER
INPUT SELECT
MULTIMEDIA
MULTIMEDIA INPUT SELECT I/II/ TEXT/ PR+/ PIP INPUT PR MUTE
ARC Changes the picture format. PIP/DW Switches the sub picture on or off PR + / or PR - / Selects a program for the sub picture.
ARC PIP/DW PR-/ SWAP MENU
I/II/ Selects the language during dual language broadcast. Selects the sound output.
*
TEXT/ These buttons are used for teletext.
*
*
*
SWAP Alternates between main and sub picture. PIP INPUT Selects the input mode for the sub picture. WIN. SIZE Adjusts the sub picture size. WIN.POSITION Moves the sub picture to D / E or F / G direction. SWAP Returns to the previously viewed programme. MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes. NUMBER buttons PSM Adjusts the factory preset picture according to the room. SPLIT ZOOM Enlarge the screen with regular ration.
MUTE Switches the sound on or off.
VOL
OK
VOL
OK
D /E Selects a menu option. F / G (Volume button) Increases/decreases sound level. Adjusts menu settings.
PR
1 4 7 PS M REVEAL HOLD INDEX
?
2 5 8 0 SIZE MIX MODE
M
3 6 9 SSM UPDATE TIME
LIST SLEEP ZOOM+ REC FF
SSM To select the sound appropriate to your viewing program character : Flat, Speech, Movie, Music, or User LIST Displays the program table. SLEEP Sets the sleep timer. ZOOM+ / ZOOMEnlarges or reduces the main picture size. VCR BUTTONS Controls a LG video cassette recorder.
WIN.POSITION WIN.SIZE SPLIT ZOOM STOP REW ZOOMP/STILL PLAY
Installing Batteries
· Open the battery compartment cover on the back side and insert the batteries with correct polarity. · Install two 1.5V alkaline batteries of AAA type. Don't mix used batteries with new batteries.
- 10 -
Accessories
POWER MULTIMEDIA ARC PIP/DW PR-/ SWAP MENU PR INPUT SELECT I/II/ TEXT/ PR+/ PIP INPUT MUTE
VOL
OK
VOL
PR
1 4 7 PSM REVEAL HOLD
?
2 5 8 0 SIZE MIX MODE
M
3 6 9 SSM UPDATE TIME
LIST SLEEP ZOOM+ REC FF
LG TV
AS mark
1.5V 1.5V
INDEX
WIN.POSITION WIN.SIZE SPLIT ZOOM STOP REW ZOOMP/STILL PLAY
Owner's Manual
Alkaline batteries
BNC-RCA adaptor (optional)
Remote Control handset
D-sub 15 pin cable
Power Cord
DVI-D Cable
Phone scart cable (Optional)
Optional Extras
Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added. Contract your dealer for buying these items.
Tilt wall mounting bracket
Wall mounting bracket
Ceiling mounting bracket
Vertical Wall mounting bracket
Desktop stand
Speakers
Desktop Speaker stand
Video cables
Audio cables
- 11 -
SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.
V
Scope
This specification can be applied to all model of 42"PDP MONITOR related to RF-03FA Chassis. Chassis RF-03FA (Monitor) Model Name MZ-42PZ44 MZ-42PZ45V MT-42PZ44/46 MT-42PZ45V/47V RF-03FA (PDP Tuner) AV BOARD RZ-BA50 RT-BA50 AP-42EA42 AP-42EA43 EU N-EU EU, Scart Type AV BOARD N-EU, RCA Type AV BOARD LG LG LG LG N-EU LG Market Place EU Brand LG
V
Test Condition
1) Temperature : 25¡ 5°C 2) Relative Humidity: 65¡ 10% 3) Power Voltage:Standard Input Voltage (AC 110V-240V~, 50/60Hz) But Standard input voltage mark value is marked by model. 4) Follow each drawing or spec for spec and performance of parts,based upon P/N of RPL 5) Warm up set for more than 20min before the measurement.
V
Test and Inspection Method
1) Performance:Follow the Standard of LG TV test 2) Extra standards Safety: Follow the standard of CE, IEC EMC : Follow the standard of CE, IEC Model Name MZ-42PZ44 MZ-42PZ45V Market EU Remark Safety: IEC60065,IEC60095 EMI : EN55013 -Conducted / Radiation RZ-BA50 EMI : EN55013 (Antenna Terminal Voltage)
EMS : EN55024 MT-42PZ44 MT-42PZ45V MT-42PZ46 RT-BA50 EMI N-EU Safety : IEC60065,IEC60095 EMI : EN55013 -Conducted / Radiation : EN55013 (Antenna Terminal Voltage)
- 12 -
V
General Specification
No 1 2 3 4 5 Item Display Screen Device Aspect Ratio PDP Module Screen Filter Operating Environment Specification 42inch wide Colour Desplay Module 16 : 9 PDP42V5####, Fish Bone 45% Total light ransmittance 1) Temp. : 0 ~ 40 °C 2)Humidity : below 85% 6 Storage Environment 1) Temp. : -20 ~ 60 °C 2)Humidity : below 85% 7 Input Voltage 110 ~240V~, 50/60Hz MURADA SONY SANKEN MZ-42PZ44/45 LGE Maker : NBK (E-Mesh) LGE Mark SPEC PDP Remark
V
Model Specification
(1) MZ-42PZ4x (MZ-42PZ44/45)
No 8 9 10 11 12 13 14 15 Item Market RGB Input DVI Input Video Input System S-Video Input Component Input Audio Input Wired Control EU VGA, SVGA, XGA, SXGA 60Hz Digital RGB Input PAL, SECAM, NTSC PAL, SECAM, NTSC 480i, 480p, 576i, 576p L/R 2 group Discrete IR Specification Remark
(2) RZ-BA50
No 16 17 18 19 20 Item Market Input Voltage Broadcasting system Receiving system Scart Jack EU DC 12V PAL B/ G/ I/ D/ K, SECAM L/ L" Upper Heterodyne PAL, SECAM Specification Remark
- 13 -
(3) MT-42PZ4x (MT-42PZ44/45V/46)
No 21 22 23 24 25 26 27 28 Item Market RGB Input DVI Input Video Input System S-Video Input Component Input Audio Input Wired Control N-EU VGA, SVGA, XGA, SXGA 60Hz Digital RGB Input PAL, SECAM, NTSC PAL, SECAM, NTSC 480i, 480p, 576i, 576p, 1080i, 1152i L/R 2 group Discrete IR Specification Remark
(2) RT-BA50
No 29 30 31 32 33
V
Item Market Input Voltage Broadcasting system Receiving system Video In/ Out System N-EU 12V
Specification
Remark
PAL B/ G/ I/ D/ K, NTSC Upper Heterodyne PAL, SECAM, NTSC
Feature and Function
No 1 2 Item Remote controller code Remote control NEC Code 1) Wireless Remote Control 2) Wired Remote Control -RCA AV B'D -Tuner Box 3 Local Key Menu, Input select V, VOLF, VOLG UpD/ DownE, Power (Main Power) 4 Set up method Wall Mount/ Desk top Pivot (Optional) 5 Featur RGB input e (MNT) - D - Sub 15 pin 1 RGB PC Input - VGA ~ 85Hz - SVGA ~ 85Hz - XGA ~ 75Hz - SXGA ~ 60Hz RGB - DTV Input -480p/ 60Hz -576p/ 50Hz -1080i/ 50Hz -1152i/ 50Hz 1 DVI - D (Digital RGB) MT-42PZ4x Pivot model Specification Remark
- 14 -
No 5
Item Feature RGB out (MNT) - D - Sub 15pin Audio input - Phone Jack RS-232C - D - Sub pin External Speak output Expanded Control 1 1 1 L/ R 1 1 1
Specification RGBHV
Remark
L/ R For RGB Input
115200bps
SPK Output 36Pin MZ-42PZ4x MT-42PZ4x Australia
Tuner Box Control 480i/ 480p/ 576i/ 576p 480i/ 480p/ 576i/ 480i/ 480p/ 576i/ 576p/ 1080i/ 1152i
6
RCA Type AVB'D
Component input (Y/ PB/ PR, Y/Cb/Cr)
Video Input(CVBS) Audio Input
1 2
PAL, SECAM, NTSC L/ R For Video/ S- Video L/ R For Component
IR Jack 7 Scart Type Tuner model ANT In (RF) - Tuner AV In/ Out -Scart Jack IR Jack DC Jack Expanded Control 8 RCA Type Tuner model ANT In (RF) AV In/ Out (CVBS) -RCA Jack IR Jack DC Jack Expanded Control 9 Scart Type AV B'D Scar Jack
1 1
Discrete IR PAL- BG/ DK/ I, SECAM-L/L' RZ-BA50 - Follow Scart In/ Out Spec - Auto AV (Scart 2 priority)
2
Scart 1 (TV Out) Scart 2 (MNT Out)
1 1 1 1 2
Wired Remote Control DC 12V In 36Pin PAL-BG/ DK/ I, NTSC PAL, SECAM, NTSC Input AV Output RT-BA50
1 1 1 2
Wired Remote Control DC 12V In 36Pin Vin, FB, RGB in, L/R in 1) TV out non-opposition 2) Auto AV non-function Vin, Lin, R in, V out, L out, R out 1) MNT out of Tuner Box non-opposition 2) Auto AV non-opposition
S- Video Input Audio Input
1 1
PAL, SECAM, NTSC L/R For S-Video
- 15 -
No 10 MENU (picture)
Item Picture Status Mode PSM
Specification 4 - Mode - Default : Standard 4 - Mode - Default : Normal
Remark
GDynamic, Standard, Mild, User Color Status Mode CSM GNormal (9,500 °K) G Cool (12,000 °K)
G Warm (8,500 °K) G User Color Temperature G R, G, B (RGB Control) Each +/- 10 Step - Default : 0 User G Contrast, Brightness, Colour, Sharpness G Tint 11 MENU (Sound) AVL(Auto Volume limit) User 12 MENU (Time) Clock Off Time Sound Status Mode SSM G Flat, Speech, Movie, Music, User On Off G Treble, Bass, Balance User Setting Off On : User Setting (Time) On Time Off On : User Setting (Time/ Volume) Auto Sleep Off On 13 MENU (special) Language (For OSD) EU 5 languages G English, French, German, Spanish, Italian 3 languages G English, Chinese, Russian Child Lock - Local key Lock ISM Method On Off G Normal : ISM action On G Orbiter : 2 min/ 2pixel a cycle G Inversion : 30 min cycle On/ Off G White Wash : Any key Off SET ID (RS- 232C control ID) Low Power On : 30% . Off 1 ~ 99 Default : Off Default : 1 --> Module Spec Default : Off Austailia/ China/ russia Default : English - etc. PR standard Default : Off Default : 12:00/ Vol. 30 Default : 12:00 Default : 12:00 Default Enable For NTSC 5 - Mode - Default : Flat - Default : OFF
- 16 -
No
Item OSD Rotate (Optional) G Normal
Specification Default : Normal Enable For Pivot
Remark
G Rotate : OSD Rotate RGB PC
14
MENU (Screen)
Auto Configure
ARC
Auto : RF/ AV/ S-AV/ Component-i 4:3 : All 16:9 : All 14:9 : RF/ AV/ S-AV/ Component-i ZOOM : RF/ AV/ S-AV/ Component-i
Disable For DW Mode
Zoom In/ Out
Zoom in/ Out (100%~ 300%)
Default :100
Position
-RGB Input -Component Input (480p/ 576p / 1152is)
Manual
Phase : 0~ 31 Colork : -50~ +50
RGB mode only
Screen Adj. Reset VGA Mode
TV / VCR O 640 x 480 848 x 480 852 x 480
RF, AV, S- Video To Initialize for user data WVGA correspondence RGB/ DVI Mode
YNR
On Off
Luminance Noise Reduction - Nothing AV B'D - Nothing Tuner Box
15
MENU
Input
MT-42PZ46
RGB $ DBI
(PIP/DW) (Main) 1)MZ-42PZ4x 2)RZ-BA50 TV$AV1(EXP)$AV2(EXP)$AV$ S-VIDEO$COMPONENT$RGB $ DVI MZ-42PZ4x 1)MT-42PZ4x 2)TE-BA50 MT-42PZ4x RGB$DVI$AV1$AV2$S-VIDEO TV$AV(EXP)$AV$S-VIDEO $COMPONENT$RGB$DVI RGB$DVI$COMPONENT$AV $S-VIDEO TV$AV1(EXO)$AV2(EXP)$RG B$DVI TV$VIDEO(EXP)$RGB$DVI TV$AV1(EXP)$AV2(EXP)$AV1 $AV2$S-VIDEO$RGB$DVI
- RCA AV B'D - Scart Tuner Box
- Scart AV B'D - RCA AV B'D - RCA Tuner Box - RCA AV B'D
- Nothing AV B'D - Scart tuner Box - Nothing AV B'D - RCA Tuner Box
- 17 -
No 15 MENU Input
Item
Specification TV$AV1(EXP)$AV2(EXP)$AV1 $AV2$S-VIDEO$RGB$DVI TV$AV(EXP)$AV1$AV2$ S-VIEDO$RGB$DVI - Scart AV B'D - Scart Tuner Box - Scart V B'D - RCA Tuner Box
Remark
(PIP/DW) (Main)
DW PIP Sub Input
OFF, DW1, DW2 OFF, ON Equal Main Input * Display Condition 1) Identity of Input Source is not Main/ Sub Display 2) Don't allow PIP/DW between graphic signals of 480p 3) When this condition appear,swap the Main/Sub screen and old input sourse. Main Input RGB, DVI Component 480 TV, AV, S-VIDEO SCART Component 480i All (Except Limitation) Available Sub Input TV, AV, S-VIDEO, SCART, Component 480i
Win, Size Win, Position PIP ARC 16 MENU (CH) Auto Program Manual Program
Variable Variable 4:3, 16:9 System, Storage(0~99), Start Storage(0~99), System, CH., Fine, Search, Name
Main/Sub screen All PIP Screen Only
- With Tuner Box - Gray Except TV Mode - Gray For MNT
Program Edit 17 Hot Key (Remote) Input Select Multimedia Input Select PIP/ DW SWAP I/ II/ * Relation Key except TEXT SPLIT ZOOM ZOOM-, ZOOM+ Power On
Del, Copy, Move, Skip Component$RGB$DVI Sequentially For Input Mode Main Input sequence
PIP$DW1$DW2$Off O (Main/Sub screen Swap) SiF Control O (TEXT action standard) 2/ 4/ 9 division 100% ~ 300% Power, Numberic(0~9), TV/ AV, Multimedia, PR +/For Tuner Boxs
Etc.
Numberic(0~9), ARC, PR+/-, VOL+/-, MUTE, PIP Input, PIP PR+/-, MENU, PSM, SSM
- 18 -
No 18 Adaptive
Item Comb Filter DCDI Film Mode Motion Detection Noise Reduction 4H Comb O X (Option) O O
Specification VPC3230 FLI2300/ FLI231 0
Remark
V
Component Video Input (Y, PB, PR)
No 1 2 3 4 5 6 Resolution 720 x 480 720 x 480 720 x 576 720 x 576 1920 x 1080 1920 x 1080 (+72) H-freq (kHz) 15.625 31.250 15.625 31.250 28.125 31.250 60.00 60.00 50.00 50.00 50.00 50.00 V-freq (Hz) Pixel clock (MHz) 13.500 27.027 13.500 27.027 74.250 74.250 480I 480P 576I 576p 1080i 1152i Proposed
V
RGB Input (PC)
No Resolution PC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 640 x 350 640 x 350 720 x 400 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 848 x 480 848 x 480 848 x 480 852 x 480 852 x 480 852 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 31.5 37.799 39.375 31.5 37.799 39.375 35.156 37.879 48.077 46.875 53.674 49.725 70.09 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 60.31 72.18 75.00 85.06 74.55 25.17 31.50 28.32 35.50 25.17 30.24 31.50 31.50 36.00 33.516 40.748 42.628 33.642 40.900 42.840 36.00 40.00 50.00 49.50 56.25 57.28 EGA EGA DOS DOS VESA(VGA) Macintosh VESA(VGA) VESA(VGA) VESA(VGA) WVGA WVGA WVGA WVGA WVGA WVGA VESA(SVGA) VESA(SVGA) VESA(SVGA) VESA(SVGA) VESA(SVGA) Macintosh H-freq (kHz) V-freq (Hz) Pixel clock (MHz) Proposed
- 19 -
No 24 25 26 27 28 29 30 31 32
V
Resolution 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1152 x 864 1152 x 870 1280 x 960 1280 x 1024
H-freq (kHz) 48.363 56.476 60.023 54.348 63.995 67.500 68.681 60.023 63.981 60.00 70.06 75.02 60.05 70.01 75.00 75.06 60.02 60.02
V-freq (Hz)
Pixel clock (MHz) 65.00 75.00 78.75 80.00 94.20 108.00 100.00 108.00 108.00
Proposed VESA(XGA) VESA(XGA) VESA(XGA) VESA(SXGA) VESA(SXGA) VESA(SXGA) VESA(SXGA) VESA(SXGA) VESA(SXGA)
RGB Input (DTV)
No 1 2 3 Resolution 1024 x 576 1920 x 1080 1920 x 1080 (+72) H-freq (kHz) 31.250 28.125 31.250 50.00 50.00 50.00 V-freq (Hz) Pixel clock (MHz) 27.027 74.250 74.250 Remarks MT-42PZ4x MT-42PZ4x MT-42PZ4x
V
PDP MODULE (PDP42V5####)
No 1 2 3 4 5 6 7 8 Display area Outline dimension Number of Pixels Number of Grdations Color Arrangement weight(net) weight(gross) Operating Environment Resolution Min Type Max Unit Mm Mm Remarks
920.1(H) x 518.4(V) +/- 0.5 1006(W) x 598(H) x 6(D) +/- 1 852(H) x 480(V) 256 steps For PC RGB RGB Vertical Stripes 15.3 106 Temp 15.8 111 : 0 ~ 40 16.3 116
Fish Bone Type kg Kg Deg % Deg % 5.5 16 Min Min Modules 5EA/ 1Box
Humidity : 20 ~ 80% 9 Storage Enironment Temp : -20 ~ 60 deg
Humidity : 10 ~ 90% 10 Image stick minimization moe Starts time The minimum brightness reaching time 4.5 14 5 15
- 20 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions are applied to all of the PDP monitor/ Tuner , RF-03FA chassis. CVBS and RGB1 input part at the same time in the Pattern Generator. (3) To check the MAX-Bias, input Full White (255 gray) signal into CVBS and RGB1 input part at the same time in the Pattern Generator. (4) Compare Black Level with White Level by eyes. And if there is no Level difference, the adjustment is completed well. Data value, which adjusted in the board, is valid until the VSC Board is dissued and must be protected. For the protection of data, Micom does not permit any more adjustment after completion. O In case of re-adjustment, operate First Value Setting.
O
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 25±5°C of temperature and 65±10% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 220V, 60Hz in adjusting. (5) The receiver must be operated for about 15 minutes prior to the adjustment. € After receiving 100% white pattern, the receiver must be operate prior to adjustment.(Or white condition in HEATRUN mode) €LEnter into HEAT-RUN mode - Select the HEAT-RUN OFF by pressing ADJ Key on Remote Control for adjustment. - Press the VOL + Key in HEAT-RUN OFF. (OSD display HEAT-RUN WHITE and screen display 100% FULL WHITE PATTERN) [ Set is activated HEAT-RUN without signal generator in this mode. [ Single color pattern of HEAT-RUN mode uses to check PANEL.(RED/BLUE/GREEN)
Each PCB Assy must be checked by the Check JIG Set before whole assembly. (Be careful the POWER PCB Assy not to damage to PDP Module)
4. POWER PCB Assy Voltage Adjustment (Va, Vs, Voltage Adjustment)
4-1. Test Equipment
D.M.M 1EA
4-2. Connection Diagram for Measuring
VS Vs ADJ
VR551
Va Va GND GND VS VS
CN 803
CN 804
[Caution] If you turn on a still screen more than 20 minutes, a afterimage may be occur in the black level part of the screen.
5V
CN 802
Va ADJ
VR351
3. RGB Auto Cut-Off & MIN Bia Adjustment
(1) Input Full Back (0 Gray) signal which generated from Pattern Generator into CVBS and RGB1 Input part. (2) Press POWER ON KEY on R/C for adjustment and select AUTO-CUT(Cut-off Auto Adjustment) (3) Press Vol. + key and operate TO SET (4) Screen adjustment starts with Full Black screen. Original Window screen will be presented about 3-5 seconds later. And if there is a mark of OK OSD, then the Auto Cut-off and Min-Bias adjustment will be completed. (5) Pass to the next MAX Bias Adjustment after Adjustment. [ Replace PDP Module or Power Board, adjust certainly Power PCB Assy Voltage.
O
CN 810
CN 809
CN 808
Connection Diagram of MURATA Power Adj. for Measuring
4-3. Adjustment Method
(1) Va Adjustment € After receiving 100% white pattern, HEAT RUN. €LConnect + terminal of D.M.M to Va pin of CN803 and connect terminal to GND pin of CN803. €Ø After turning the VR351, voltage of D.M.M adjustment as same as Va voltage which on label of panel Right/Top. (Deviation : ±0.5V)
You can check whether circuit adjustment is operated well or not, as below. (1) Display RGB1 to the Main picture, CVBS to the Sub picture in the TWIN PICTURE. (2) To check the MIN-Bias, input Full Black (0 gray) signal into
- 21 -
(2) Vs Adjustment € Connect + terminal of D.M.M to Vs pin of P805 and connect terminal to GND pin of CN803. €L After turning the VR551, voltage of D.M.M adjustment as same as Vs voltage which on label of panel Right/Top. (Deviation : ±0.5V)
5. Adjustment of White Balance
6-2. Setting of Device 5-1. Required Equipment
Color analyzer (CA-100 or same product)
6-3. Preparation for Adjustment
(1) Set devices as above and turn the PC, jig on. (2) Put S/W for writing DDC (EDID data write & read) into operation. (operated in DOS mode.)
5-2. Connection Diagram of Equipment for Measuring (Manual Adjustment)
R-L 70 G-L 70 R-M 128 G-M 128 R-H 216 G-H 216
6-4. Sequence of Adjustment
(1) DDC Data Input for Analog-RGB € Put the set on the table and turn the power on.
High Light adjustment 216 Gray Level 2 105 ~ 115 Cd/m
RGB Signal Input
Window MSPG-2100 or MSTG-5200
€LConnect PC Serial to D-sub 15P Cable of JIG for DDC Adjustment to RGB terminal (D-Sub 15Pin). €Ø Operate S/W for DDC record and select DDC Data for Analog RGB in Model Menu. €OE Operate EDID Write command. €º Operate EDID Read command and check whether Check Sum is OK. € If Check Sum is NG, repeat c) ~ d). € If Check Sum is OK, DDC Data for Analog-RGB input is completed. (2) DDC Data input for Digital-RGB € Connect PC Serial to DVI Cable of JIG for DDC Adjustment to RGB2 terminal (DVI Jack). €LOperate S/W for DDC record and select DDC Data for Digital RGB in Model Menu. €ØOperate EDID Write command. €OE Operate EDID Read command and check whether Check Sum is OK. €ºIf Check Sum is NG, repeat c) ~ d). € If Check Sum is OK, DDC Data for Digital-RGB input is completed.
Connection Diagram of Manual Adjustment
5-3. Adjustment of White Balance
O O
Operate the Zero-calibration of the CA-100, then stick sensor to PDP module surface when you adjust. For manual adjustment, it is also possible by the following sequence.
(1) Select WHITE PATTERN of HEAT RUN mode by pressing POWER ON KEY on remote control for adjustment then operate HEAT RUN more than 10 minute. (2) Supply 216Gray Level, 50% size length and breadth signal to RGB input. (Refer to Fig 2) (3) To adjust High Light, stick sensor to 216Gray Level(or 105~115 Cd/m2) Pattern, press ADJ Key on R/C for adjustment and press D, E on R/C in adjustment mode to select R-L or G-L, press VOL +, - Key and adjust it until color coordination becomes as below. [MZ-42PZ4x, MT-42PZ4x] X: 0.270±0.003, Y: 0.267±0.003 Color temperature: 13,000°K±500°K (4) Exit adjustment mode using V Key.
6. DDC Data Input
6-1. Required Test Equipment
(1) A jig for adjusting PC, DDC. (PC serial to D-sub. Connection equipment) (2) S/W for writing DDC(EDID data write & read) (3) D-Sub 15P cable, D-Sub to DVI Connector (Connect to DVI Jack)
- 22 -
PC L/R RGBA (EVEN) RGBB (ODD) RGB 48 bit
DSUB PC- OUT
DSUB PC- IN
DVI- D
IC202 Sil169B TMDS_RX 3.3V #4
IC502/503/504 K4S643232E SDRAM (8Mbyte) 3.3V #9
PIGGYBACK BOARD
RGB CH1 CH0 DTV RGB
AD9888: unselect . by IC power down Sil161B: unselect by output floating. 48
IC405 K4S643232E SDRAM(8Mbyte) 3.3V #7 RGBA(EVEN) RGBB(ODD)
PIGGY L/R
H/V RGB
TXT RGB/FB
Monostable Multivibrator Y,Pb,Pr (480p ¡è) : high Y,Cb,Cr (480i) : low
IC201 AD9888 ADC 3.3V #3
Wired _OR Cntl
H/V Sync. For Teletext
TXT RGB/ SCART RGB
IC105 CXA2101Q 5V #2 YUV 16 bit
IC404 FLI2300 De_interlace 3.3V/2.5V #7
RGBB IC501 Rembrandt-I 24 Scaler 5V/3.3V/1.8V #8
IC601 Sil160 TMDS_TX 3.3V #10
8
YUV 16 bit
Piggy CVBS2
Y/ Pb/Pr (480PÀÌ»ó)
Piggy CVBS1
SCART RGB/FB
A/V CVBS
IC401 VPC3230 Decoder 5V/3.3V #6 IC402 74LS123 5V #6 U-Com ID Y/Pb/Pr(480i) 1H R/G/B Y/C
Piggy CVBS2
IC404 FLI2310 De_interlace 3.3V/2.5V #7
IC405 K4S643232E SDRAM(8Mbyte) 3.3V #7
BLOCK DIAGRAM
- 23 PIGGY CVBS1 AV CVBS1 SCART RGB/FB
IC401 VPC3230 Decoder 5V/3.3V #6 PIGGY L/R A/V L/R PC L/R MNT L/R IC101 MSP3440 Sound Processor L/R IC105 LA4282 AUDIO AMP L/R
A/V L/R
Y/C
A/V L/R
AV CVBS2
AV BOARD
Y/Pb/Pr(480i) 1H R/G/B
H/V/CLK/ FIELD
Indicate even/odd for de_interlace
1H RGB/ Component
S- Video
AV CVBS1
AV CVBS2
AV L/R
ASSEMBLY METHOD
1. MODULE of part and PLATE A/V unite two things. 2. Unite after put on BACK COVER INNER of part . 3. Disassembly is opposite to Assembly. NOTE> Working sequence of Part is different from Part.
- 24 -
PRINTED CIRCUIT BOARD
MAIN (TOP)
- 25 -
MAIN (BOTTOM)
- 26 -
AV BOARD (TOP)
AV BOARD (BOTTOM)
AV FIX BOARD (TOP)
AV FIX BOARD (BOTTOM)
- 27 -
CONTROL BOARD (TOP)
CONTROL BOARD (BOTTOM)
SPEAKER (TOP)
POWER SWITCH
SPEAKER (BOTTOM)
- 28 -
MEMO
- 29 -
EXPLODED VIEW
300
305
301
200
206 204 201 205 220 102
580
202 203
520 521 524
523 540 551 550 570 541
430
101
560 470 530 522
490
400
552
410 401
710
700 720
- 30 -
EXPLODED VIEW PARTS LIST
No.
101 102 200 201 202 203 204 205 206 210 220 300
Part No.
5900V04009A 4980V00985B 6348Q-E036A 6348Q-E038B 6871QDH051A 6871QDH052A 6871QCH025A 6871QCH031C 6871QYH027A 6871QYH027B 6871QRH034A 6871QZH030A 6871QZH030B 4980V00460A 4980V00460B 4980V00464B 4980V00464C 3091V00B01S 3091V00B01P 3091V00B01T SUPPORTER, FAN EGI SKD
Description
FAN,DC 412F/39M PAPST 40*40*10 12V/45MA 4300RPM 17 PDP 42" PDP, 42" 16:9 852*480 PDP42V50000(KK MODEL), FOR INTERCOMPANY DOMESTIC, WOODEN PALLET PDP, 42" 16:9 852*480 PDP42V50330.ADLGA PWB ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42SD5_YDRV_TOP_TI_4LAYER PWB ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42SD5_YDRV_BTM_TI_4LAYER PWB ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42SD5 CTRL BD(LPCMC1121) PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V5 TMDS LGPCMV1222H PWB ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42SD5_SEPERATED_YSUS PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V5 SONY STANDRAD PWB ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42SD5_XR_SEPERATE(4 LAYER) PWB ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42SD5(YZ SEPARATE) PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V5 SONY STANDARD SUPPORTER, VERTICAL MN-42PZ40 . SUPPORTER, MODULE EGI SKD SUPPORTER, SPK SBHG SUPPORTER, SPK SBHG MT-42PZ41V CABINET ASSEMBLY, MZ-42PZ44 KK MODULE MZ-42PZ43VS RE02RA SKD CABINET ASSEMBLY, MZ-42PZ44 KK VGA SKD CASE, ASSY MN-42PZ40 CASE, ASSY MT-42PZ41V LGESY SKD FILTER(MECH) MN-42PZ40S 1142G03E GLASS NBK MESH SINGLE AR FILTER(MECH), MN42PZ41 LGM42-01 MITSUI 42" ETCHING MESH GLASS FILTER BACK COVER ASSEMBLY BACK COVER ASSEMBLY, MZ-42PZ45V SKD PLATE ASSEMBLY, A/V PLATE ASSEMBLY, A/V 3300V00205D WALES SKD BACK COVER ASSEMBLY BACK COVER ASSEMBLY, MZ-42PZ44 KK VGA SKD SHIELD, PLATE MZ-42PZ44 RF03FA ET SUSTAIN SHIELD, PLATE MZ-42PZ44 RF03FA ET SKD SHIELD, PLATE MZ-42PZ44 RF03FA ET SKD SHIELD, COVER RJ-42PZ40 RF02KC AL AC SOCKET SHIELD, MN-42PZ40 RF02RA AL SKD PWB(PCB) ASSEMBLY,MAIN RF-03FA MT NORMAL PWB(PCB) ASSEMBLY,MAIN RF-03FA RUSSIA PWB(PCB) ASSEMBLY,MAIN RF03FA MANUAL VSC PIGGY BACK SHIELD, CASE MZ-42PZ44 SBHG TOP PRESS SHIELD, CASE MZ-42PZ44 SBHG MIDDLE PRESS SHIELD, CASE MZ-42PZ44 SBHG BOTTOM PRESS PWB ASSEMBLY,SUB CONT RF03GA MU-42PZ44 PWB ASSEMBLY,SUB PSW RF03GA MU-42PZ44 BUTTON, POWER MT-42PZ41V ABS, AF-303S 1KEY BUTTON, POWER MT-42PZ41V ABS, AF-303S 1KEY LGESY SKD PWB ASSEMBLY,SUB INTER RF03FA FIX B/D ASSY SUPPORTER, AV INTERFACE SBHG MU-42PZ41 SUPPORTER SUPPORTER AV INTERFACE SUPPORTER, AV INTERFACE EGI MZ-42PZ44 SKD PWB ASSEMBLY,SUB SPK RF03GA MU-42PZ44 PWB ASSEMBLY,SUB A/V RF03FA PIGGYBACK-RCA BOARD ASSEMBLY, POWER MZ42PZ44 RF03FA MPF7407 MURATA 42KK BOARD ASSEMBLY, POWER MT42PZ44 RF03FA MPF7407 MURATA 42KK CASE, TUNER RZ-BA50 EGI BOTTOM ASSY CASE, TUNER RT-BA50 EGI BOTTOM ASSY PWB ASSEMBLY,MAIN RF03FA PIGGYBACK STB-SCART PWB ASSEMBLY,MAIN RF03FA PIGGYBACK STB-SCART CASE, TUNER RZ-BA50 EGI TOP ASSY CASE, TUNER RT-BA50 EGI TOP ASSY
301 305 400 401 410 470
3110V00229A 3110V00229B 3790V00281E 3790V00709B 3809V00A47K 3809V00A47M 3301V00010G 3301V00010R 3809V00A58F 3809V00A58G 4814V00344C 4814V00344D 4814V00344F
490 520
4814V00309B 4814V00309D 6871VMMQ79A 6871VMMQ79C 6871VMM498B
522 523 524 530 540 541 550 551 552 560 570 580 580 700 710 720
4814V00357C 4814V00358C 4814V00359C 6871VSMU44A 6871VSMV04A 5020V00666A 5020V00666C 6871VSMU96A 4980V00465D 4980V00465F 4980V00748C 4980V00748J 6871VSMU45A 6871VSMU53B 3501V00149A 3501V00149B 3110V00237E 3110V00237F 6871VMM499B 6871VMM500C 3110V00242E 3110V00242F
TUNER (RT/RZ-BA50)
- 31 -
REPLACEMENT PARTS LIST (MONITOR)
LOCA. NO PART NO DESCRIPTION LOCA. NO IC904 IC915 IC001 IC002 IC101 IC102 IC103 IC104 IC1101 IC1102 IC1103 IC1104 IC201 IC202 IC205 IC301 IC401 IC403 IC405 IC406 IC407 IC408 IC409 IC501 IC502 IC503 IC504 IC601 IC701 IC702 IC703 IC704 IC741 IC742 IC743 IC744 IC745 IC746 IC747 IC748 IC749 IC750 IC751 IC802 IC850 IC852 IC853 IC857 IC858 IC859 IC901 IC902 IC903 0ISO208900A 0IMCRFA010A 0IAL242110A 0IAL242110A 0IMCRTI003A 0IPRPBB005A 0IDS162100B 0IMCRPH015A 0ISH092100B 0ISH122100B 0ISO210100B 0IPRPTI001A 0IMCRTI003A 0IMCRAD003A 0IIT323000E 0IFA741230A 0IMCRGN001B 0IMMRHY033A 0IIT323000E 0IMCRGN002B 0IMMRHY033A 0IMCROT001A 0IMMRHY033A 0IMMRHY033A 0IMMRHY033A 0IS5160000A 0IMCRRS001A 0IMMRSS064A 0IMMRMR006A 0IMMRAL025A 0IMCRFA013A 0IMCRFA013A 0ITI745740M 0IMCRPH017A 0IPH740800L 0IMCRPH015A 0IMCRPH016A 0IMCRPH014A 0IKE702700D 0IDS232000A 0IPH858400A 0ISA428200A 0IMCRSJ001A 0IMCRFA010A 0IMCRRH001A 0IMCRRH001A 0IMCRSH001A 0IMCRSH001A 0IMCRMN014A 0IKE780800J 0IMCRSH001A IC, CXA2089Q 48QFP BK A/V SWITCH IC, KA7809R, FAIRCHILD 2P D-PAK, R/TP REGULATOR IC, AT24C21-10SI-2.5 8P,SOP TP 1K EEPROM IC, AT24C21-10SI-2.5 8P,SOP TP 1K EEPROM IC, SN74HCT08D TEXAS INSTRUMENT 16P R/TP IC, OPA3692IDBQ BUR BROWN 16PIN SSOP R/TP IC, DS1621V 8P SOIC ST THERMOSTAT IC, 74LVC32AD PHILIPS 14P SOT108-1 R/TP IC, PQ09RD21 4SIP ST REGULATOR IC, PQ12RD21 4SIP ST REGULATOR IC, CXA2101AQ 80P,QFP BK VIDEO SIGNAL IC, TFP401PZP TEXAS INSTRUMENT 100,TQFP R/TP IC, SN74HCT08D TEXAS INSTRUMENT 16P R/TP IC, AD9888KS-140 ANALOG DEVICE 128P MQFP IC, VPC3230D C5 80P QFP TRAY VIDEO IC, DM74LS123MX 16SOP TP DUAL RETRIG. IC, FLI2310BC GENESIS 208P PQFP IC, HY57V643220C(L)T-6 HYNIX 86P TSOP IC, VPC3230D C5 80P QFP TRAY VIDEO IC, FLI2300BC GENESIS 208P PQFP IC, HY57V643220C(L)T-6 HYNIX 86P TSOP IC, REMBRANT-1A OPLUS TECHNOLOGIES LTD 352BALL IC, HY57V643220C(L)T-6 HYNIX 86P TSOP IC, HY57V643220C(L)T-6 HYNIX 86P TSOP IC, HY57V643220C(L)T-6 HYNIX 86P TSOP IC, SII160 100 TQFP ST PANELLINK IC, R8820LV RDC SEMICONDUCTOR LTD 100P PQFP IC, K6R4016V1D-TC10 44P TSOP2-400BF R/TP 4M(256K*16) IC, COPY MX29LV160TTC-70 MACRONIX 48P TSOP R/TP IC, AT24C32AN-10SI-2.7 ATMEL 8PIN SOP TP 32K 3.3V IC, 74LCX244MTC FAIRCHILD 20P TSSOP R/TP IC, 74LCX244MTC FAIRCHILD 20P TSSOP R/TP IC, SN74HC574NSR 14P,SOP TP D-TYPE EDGE IC, 74LVC574APW 20P SOT360-1 R/TP D-TYPE FLIP-FLOP IC, 74LVT08D 14SOP R/TP LOW VOLTAGE AND DI-32Q82 IC, 74LVC32AD 14P SOT108-1 R/TP QUAD 2-IN OR GATE IC, 74LVC139D PHILIPS 16P SOT109-1 R/TP IC, 74LV132D 14P SOT108-1 R/TP QUAD 2-IN IC, KIA7027AF 3, SOT-89 TP RESET IC 2.7V IC, DS232AS 16P,SOP TP RS-232 DRIVER/RECEIVER IC, PCF8584T 20P,SOP TP IIC BUS CONTROLLER IC, LA4282 12S 2CHX10W AUDIO AMP IC, SC1565IST-1.8 SEMTECH 3P SOT223 TP REGULATOR IC, KA7809R, FAIRCHILD 2P D-PAK, R/TP IC, BA033FP ROHM 3P-SOP,TO252-3 R/TP 3.3V REGULATOR IC, BA033FP ROHM 3P-SOP,TO252-3 R/TP 3.3V REGULATOR IC, PQ05DZ1U SHARP 5, SMD TYPE R/TP REGULATOR IC, PQ05DZ1U SHARP 5, SMD TYPE R/TP REGULATOR IC, MSP3440G QA B8 V3 MICRONAS 80 QFP IC, KIA7808API 3 ST REGULATOR . IC, PQ05DZ1U 5, SMD TYPE R/TP REGULATOR IC203 IC204 Q001 Q001 Q001 Q002 Q002 Q002 Q003 Q003 Q004 Q005 Q006 Q007 Q008 Q008 Q009 Q009 Q200 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q211 Q212 Q213 Q214 Q215 Q216 Q217 Q218 Q219 Q220 Q221 Q270 Q271 Q272 Q403 Q404 Q474 Q475 Q476 0TR830009BA 0TR830009BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR150400BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA IC917 PART NO 0IKE704200J 0IMCRTI001A 0IFA742530B DESCRIPTION IC, KIA7042AF SOT-89 TP 4.2V VOLTAGE DETECTOR IC, SN74HCT157D TEXAS INSTRUMENT 16P R/TP RL-JA10 IC, 74ACT253SC 16P-SOIC, JEDEC MS-012 R/TP
IC
TRANSISTOR
TR, BSS83 TP N-CHANNEL S/W TR, BSS83 TP N-CHANNEL S/W TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SA1504S(ASY) KEC
- 32 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO Q477 Q478 Q700 Q720 Q721 Q722 Q723 Q724 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909
PART NO 0TR387500AA 0TR104009AF 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA
DESCRIPTION TR, CHIP 2SC3875S(ALY) KEC TR, CHIP KRC104S SOT-23 TP KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SA1504S(ASY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC TR, CHIP 2SC3875S(ALY) KEC
LOCA. NO DA105 LD740 LD741 LD742 LD743 ZD001 ZD002 ZD830 ZD831 ZD832
PART NO 0DD226239AA 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA
DESCRIPTION DIODE, CHIP KDS226 SOT-23 LED GREEN/RED GREEN:10MCD, RED:6MCD LED GREEN/RED GREEN:10MCD, RED:6MCD LED GREEN/RED GREEN:10MCD, RED:6MCD LED GREEN/RED GREEN:10MCD, RED:6MCD DIODE, SD05.TC R/TP SEMTECH SOD323 5V 5A 15A DIODE, SD05.TC R/TP SEMTECH SOD323 5V 5A 15A DIODE, SD05.TC R/TP SEMTECH SOD323 5V 5A 15A DIODE, SD05.TC R/TP SEMTECH SOD323 5V 5A 15A DIODE, SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
CAPACITOR
C002 C005 C006 C007 C008 C010 C012 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE106SF6DC 0CE476SF6DC 0CE227VF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE106SF6DC 0CE476SF6DC 0CE106SF6DC 0CE107SF6DC 0CE474SK6DC 0CE474SK6DC 0CE476SF6DC 0CE105SK6DC 0CE335SK6DC 0CE106SF6DC 0CE105SK6DC 0CE474SK6DC 0CE105SK6DC 0CE474SK6DC 0CE105SK6DC 0CE474SK6DC 0CE105SK6DC 0CE474SK6DC 0CE105SK6DC 0CE107SF6DC 0CE105SK6DC 0CE107SF6DC 0CE105SK6DC 0CE476SF6DC 0CE105SK6DC 0CE476SF6DC 0CE105SK6DC 0CE227VF6DC 0CE477DK618 0CE476SF6DC 0CE477DK618 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 3.3UF MVG 50V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 1UF MVG 50V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 100UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 100UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 470UF STD 50V 20% FL TP 5 47UF MVG 16V M SMD R/TP 470UF STD 50V 20% FL TP 5
DIODE
D001 D001 D002 D003 D004 D006 D011 D100 D101 D102 D105 D106 D107 D108 D109 D110 D111 D112 D113 D114 D115 D117 D118 D854 D855 D857 D870 D872 D873 D880 D881 D882 D883 0DD184009AA 0DL200000CA 0DD184009AA 0DD184009AA 0DD184009AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD184009AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC DIODE, KDS184S CHIP 85V 300MA KEC TP LED SAM5670(DL-2LRG) BK Y-GREEN DIODE, KDS184S CHIP 85V 300MA KEC TP DIODE, KDS184S CHIP 85V 300MA KEC TP DIODE, KDS184S CHIP 85V 300MA KEC TP DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, KDS184S CHIP 85V 300MA KEC TP DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 DIODE, CHIP KDS226 SOT-23 LED GREEN/RED GREEN:10MCD, RED:6MCD LED GREEN/RED GREEN:10MCD, RED:6MCD LED GREEN/RED GREEN:10MCD, RED:6MCD LED GREEN/RED GREEN:10MCD, RED:6MCD
C013 C014 C014 C015 C015 C017 C018 C019 C019 C020 C020 C021 C022 C022 C023 C023 C024 C024 C025 C025 C026 C029 C030 C030 C031 C034 C035 C038 C039 C040 C041 C042 C042
- 33 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO C043 C044 C045 C045 C046 C047 C047 C048 C050 C053 C056 C057 C058 C059 C090 C091 C092 C109 C110 C1102 C1106 C1107 C1108 C111 C112 C113 C114 C117 C119 C121 C123 C126 C127 C211 C216 C221 C273 C277 C292 C294 C295 C300 C310 C314 C387 C388 C389 C390 C396 C401 C416 C417
PART NO 0CE476SF6DC 0CE107DH618 0CE476SF6DC 0CE106SF6DC 0CQ1521N509 0CE107DH618 0CE476SF6DC 0CQ1521N509 0CE476SF6DC 0CE106SF6DC 0CE107DH618 0CQ1041N509 0CE106SF6DC 0CQ1041N509 0CE474SK6DC 0CE474SK6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE106SF6DC 0CE227VF6DC 0CE105SK6DC 0CE105SK6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477VF6DC 0CE477VF6DC 0CE477VF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE105SK6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE106SF6DC 0CE106SF6DC 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE106SF6DC 0CE107SF6DC
DESCRIPTION 47UF MVG 16V M SMD R/TP 100UF STD 25V M FL TP5 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 0.0015U 100V K POLY TP
LOCA. NO C419 C433 C434 C436 C437 C438 C442 C443 C444 C447 C456 C479 C485 C488 C489 C491 C494 C502 C503 C504 C510 C523 C524 C671 C672 C673 C674 C675 C676 C724 C760 C765 C766 C769 C772 C785 C786 C787 C788 C789 C791 C793 C810 C811 C817 C820 C824 C826 C828 C833 C839 C881
PART NO 0CK224DF56A 0CK224DF56A 0CE106SF6DC 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CE106SF6DC 0CK224DF56A 0CE106SF6DC 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CK224DF56A 0CN105EJ56A 0CE106SF6DC 0CE477DK618 0CE477DK618 0CE477DK618 0CE477DK618 181-120K 181-120K 0CE105SK6DC 0CE477VF6DC 0CE477VF6DC 0CE477VF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE227VF6DC 0CE227VF6DC 0CE476SF6DC 0CE476SF6DC 0CE106SF6DC 0CE227VF6DC 0CE477VF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CN105EJ56A 0CE107SF6DC
DESCRIPTION 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 10UF MVG 16V 20% R/TP(SMD) SMD 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 220000PF 2012 16V 10% R/TP X7R 10UF MVG 16V 20% R/TP(SMD) SMD 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 1.0UF 3216 35V 10% R/TP X7R 10UF MVG 16V 20% R/TP(SMD) SMD 470UF STD 50V 20% FL TP 5 470UF STD 50V 20% FL TP 5 470UF STD 50V 20% FL TP 5 470UF STD 50V 20% FL TP 5 2200PF 4KV M E FMTW LEAD 4.5 2200PF 4KV M E FMTW LEAD 4.5 1UF MVG 50V M SMD R/TP 470UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 1.0UF 3216 35V 10% R/TP X7R 100UF MVG 16V M SMD R/TP
100UF STD 25V M FL TP5 47UF MVG 16V M SMD R/TP 0.0015U 100V K POLY TP
47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 100UF STD 25V M FL TP5 0.1U 100V K POLY TP
10UF MVG 16V 20% R/TP(SMD) SMD 0.1U 100V K POLY TP
0.47UF MVG 50V M SMD R/TP 0.47UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 470UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 220000PF 2012 16V 10% R/TP X7R 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP
- 34 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO C884 C887 C890 C893 C912 C913 C914 C915 C928 C929 C930 C931 C949 C951 C964 C965 C966 C967 C968 C969 C971 C973 C980 C981 C982 C984 C986 C993 C994 C995
PART NO 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477VF6DC 0CE477VF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE227VF6DC 0CE227VF6DC 0CE477VF6DC 0CE477VF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE227VF6DC 0CE227VF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC
DESCRIPTION 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 470UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP
LOCA. NO P002A P002B P005A P005B P036 P100A P101 P101A P102A P102B P104 P105A P106A P107A P108 P108A P111A P600 P741 P800 P801 P802 P803
PART NO 366-921K 366-921K 366-921L 366-921L 6630V601236 6630VL01380 6630VGA001C 6630VL04008 366-932C 387-B04C 6630VGA001C 366-921J 366-921L 366-921K 6602T12002M 6602T12002M 366-932D 6602T11001A 6630VGA004B 6602V25009L 6602V25009F 366-932B 366-932B
DESCRIPTION CONNECTOR, WAFER 2.5MM 11P GIL-G CONNECTOR, WAFER 2.5MM 11P GIL-G CONNECTOR, WAFER 2.5MM 12P GIL-G CONNECTOR, WAFER 2.5MM 12P GIL-G CONNECTOR, WAFER MDR-36 CONNECTOR, WAFER 2-557101-1 AMP 80P 2.54MM CONNECTOR D-SUB 68114-1521 MOLEX 15PIN 2.29MM CONNECTOR, WAFER-AMP 8P 2.5MM 0-0171825-8 CONNECTOR, WAFER 2.5MM 4P GIL-G CONNECTOR ASSEMBLY 4P 2.5MM 200MM H-B UL1185AWG26 CONNECTOR D-SUB 68114-1521 15PIN 2.29MM ANGLE SN CONNECTOR, WAFER 2.5MM 10P GIL-G CONNECTOR, WAFER 2.5MM 12P GIL-G CONNECTOR, WAFER 2.5MM 11P GIL-G CONNECTOR, WAFER 53261-1390 13P 1.25MM R/A SMD CONNECTOR, WAFER 53261-1390 13P 1.25MM R/A SMD CONNECTOR, WAFER 2.5MM 5P GIL-G CONNECTOR, WAFER FI-TWE21P-VF JAE 21P 1.25MM S/T CONNECTOR D-SUB 69107-0921 MOLEX 9P 2.77MM CONNECTOR, WAFER 2.5MM 12P 1-171825-2 AMP MN-42PZ10 CONNECTOR, WAFER 2.5MM 7P 0-171825-7 AMP CONNECTOR, WAFER 2.5MM 3P GIL-G CONNECTOR, WAFER 2.5MM 3P GIL-G LG
JACK
JP1 P101 P102 P102 P103 P103 P104 6612VLH002A 6612JH003CA 380-068D 6612J00010A 380-363K 6612BBBHN6A 6612VMV002A 6612JH003CA 380-068E JACK, SP026B PARK ELEC 4P RD/BK/BK/RD JACK, PPJ137A PARK ELEC. AUDIO L-MONO JACK, UEJ-CV-003 UGCOM E/P WITH S/W JACK, PPJ128A-1 PARKELEC A/V 2P JACK, PJ6046G PARKELEC H=8.0 JACK, 440062-1 AMP DVI INTERACED RIGHT ANGLE JACK, UCT-EX-020 UGCOM BNC MONO JACK, PPJ137A PARK ELEC. AUDIO L-MONO JACK, UEJ-CV-018 UGCOM D3.5 E/P
COIL & INDUCTOR
L200 L400 L401 L402 L403 L404 L405 L406 L470 L471 L472 L473 L474 L870 L886 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 0LC0233002A 6140VB0004B 6140VB0004B INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP INDUCTOR 3.3UH CERATECH R/TP COIL,CHOKE 26UH 1UEWPHY 22.5TURN YL-9N 0.4 COIL,CHOKE 26UH 1UEWPHY 22.5TURN YL-9N 0.4
P105 P106
RESISTOR
A692 AR260 AR261 AR262 AR263 AR264 AR265 AR266 AR267 AR268 AR269 AR270 AR271 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R
CONNECTOR
A6 P001A P001B 6866VA9001B 366-921J 366-921J CONNECTOR D-SUB 2990-9C UL 1161 AWG 26 CONNECTOR, WAFER 2.5MM 10P GIL-G CONNECTOR, WAFER 2.5MM 10P GIL-G
AR330 AR332 AR333
- 35 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO AR334 AR335 AR336 AR337 AR338 AR339 AR340 AR341 AR342 AR400 AR401 AR402 AR403 AR404 AR405 AR406 AR407 AR460 AR461 AR462 AR463 AR465 AR466 AR467 AR468 AR469 AR470 AR471 AR472 AR473 AR474 AR475 AR512 AR513 AR514 AR515 AR550 AR551 AR552 AR553 AR589 AR590 AR691 AR693 AR694 AR695 AR696 IC330 IC332 IC333 IC334 IC335
PART NO 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001C 0RRZVTA001C 0RRZVTA001C 0RRZVTA001C 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D
DESCRIPTION 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES HN-61A40R 22 OHM 1 / 16 W 1608 5% R/TP 4P E24