Text preview for : DCR-HC21 ADJ.pdf part of SONY SONY DCR-HC21 S.M.
Back to : SONY DCR-HC21.part1.rar | Home
DCR-HC21
RMT-830
Ver 1.0 2005.01 SEÇÃO 6 ADJ
Revision History AJUSTES
Link
Before starting adjustments VIDEO SECTION ADJUSTMENTS
Adjusting items when replacing main parts and boards PREPARATIONS BEFORE ADJUSTMENTS
(Non MS model)
SYSTEM CONTROL SYSTEM ADJUSTMENTS
Adjusting items when replacing main parts and boards
(MS model) SERVO AND RF SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS (Non MS model)
PREPARATIONS BEFORE ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS (MS model)
INITIALIZATION OF 8, A, C, D, E, F, 1C, 1F
PAGE DATA (Non MS model)
SERVICE MODE
INITIALIZATION OF 8, A, B, C, D, E, F, 18, 1A,
1B, 1C, 1E, 1F PAGE DATA (MS model) ADJUSTMENT REMOTE COMMANDER
CAMERA SYSTEM ADJUSTMENTS DATA PROCESS
ELECTRONIC VIEWFINDER SYSTEM SERVICE MODE
ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
MECHANISM SECTION ADJUSTMENTS
HOW TO ENTER RECORD MODE WITHOUT
CASSETE
HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETE
TAPE PATH ADJUSTMENT
NON MS model: DCR-HC21
CÂMARA DE VÍDEO DIGITAL
DCR-HC21 2004L0500-1
© 2005.03
9-876-782-51 Sony EMCS Co. - Sony Brasil Ltda. Publicado por Engenharia da Qualidade
ÍNDICE
Section Title Page Section Title Page
6. ADJUSTMENTS 3. Flange Back Adjustment
1. Before Starting Adjustments ··········································· 6-1 (Using the minipattern box or
1-1. Adjusting Items when Replacing Main Parts and flange back adjustment jig) ··········································· 6-35
Boards (Non MS model) ················································· 6-2 4. Flange Back Adjustment
1-2. Adjusting Items when Replacing Main Parts and (Using the flange back adjustment chart and
Boards (MS model) ························································· 6-4 subject more than 500 m away) ····································· 6-36
6-1. Camera Section Adjustments ··········································· 6-6 4-1. Flange Back Adjustment (1) ·········································· 6-36
1-1. Preparations before Adjustments (CAMERA Section) ··· 6-6 4-2. Flange Back Adjustment (2) ·········································· 6-37
1-1-1. List of Service Tools ························································ 6-6 5. Flange Back Check ························································ 6-37
1-1-2. Preparations ····································································· 6-7 6. Optical Axis Adjustment ··············································· 6-38
1-1-3. Precaution ········································································ 6-8 7. Picture Frame Setting
1. Setting the Switch ···························································· 6-8 (Color reproduction adjustment frame) ························· 6-39
2. Order of Adjustments ······················································ 6-8 8. Picture Frame Setting (Center frame) ··························· 6-40
3. Subjects ··········································································· 6-9 9. F No. standard data input ·············································· 6-40
4. Preparing the Flash Adjustment Box ····························· 6-10 10. Mechanical Shutter Adjustment
1-2. Initialization of 8, A, C, D, E, F, 1C, 1F Page Data (DCR-HC32/HC32E/HC33/HC33E) ···························· 6-41
(Non MS model) ···························································· 6-11 11. Color Reproduction Adjustment ···································· 6-42
1-2-1. Initialization of A, D Page Data ···································· 6-11 12. Auto White Balance Standard Data Input ····················· 6-43
1. Initializing of A, D Page Data ······································· 6-11 13. LV Standard Data Input ················································· 6-43
2. Modification of A, D Page Data ···································· 6-11 14. Auto White Balance Adjustment ··································· 6-44
3. A Page Table ·································································· 6-12 15. Auto White Balance Check ··········································· 6-45
4. D Page Table ·································································· 6-12 16. MAX GAIN Adjustment ··············································· 6-46
1-2-2. Initialization of 8, C, 1C Page Data ······························· 6-13 17. Steadyshot Check ·························································· 6-47
1. Initializing of 8, C, 1C Page Data ································· 6-13 1-5. Electronic Viewfinder System Adjustments ·················· 6-48
2. Modification of 8, C, 1C Page Data ······························ 6-13 1. EVF Automatic Adjustment (LB-109 board) ················ 6-48
3. 8 Page Table ··································································· 6-14 1-6. LCD System Adjustments ············································· 6-49
4. C Page Table ·································································· 6-14 1. LCD Automatic Adjustment (PD-237 board) ················ 6-49
5. 1C Page Table ································································ 6-15 2. V-COM Adjustment (PD-237 board) ···························· 6-50
1-2-3.Initialization of E, F, 1F Page Data ································ 6-16 3. Transmissive Mode White Balance Adjustment
1. Initializing of E, F, 1F Page Data ·································· 6-16 (PD-237 board) ······························································ 6-50
2. Modification of E, F, 1F Page Data ······························· 6-16 6-2. Mechanism Section Adjustments ·································· 6-51
3. E Page Table ·································································· 6-17 2-1. How To Enter Record Mode Without Cassette ·············· 6-51
4. F Page Table ·································································· 6-17 2-2. How To Enter Playback Mode Without Cassette ·········· 6-51
5. 1F Page Table ································································ 6-19 2-3. Tape Path Adjustment ···················································· 6-51
1-3. Initialization of 8, A, B, C, D, E, F, 18, 19, 1. Preparation for Adjustment ··········································· 6-51
1A, 1B, 1C, 1E, 1F Page Data (MS model) ·················· 6-20 2. Procedure After Operations ··········································· 6-51
1-3-1. Initialization of A, B, D, 1A, 1B Page Data ·················· 6-20 6-3. Video Section Adjustments ··········································· 6-52
1. Initializing of A, B, D, 1A, 1B Page Data ····················· 6-20 3-1. Preparations Before Adjustments ·································· 6-52
2. Modification of A, B, D, 1A, 1B Page Data ·················· 6-20 3-1-1. Equipment Required ······················································ 6-52
3. A Page Table ·································································· 6-21 3-1-2. Precautions on Adjusting ··············································· 6-52
4. B Page Table ·································································· 6-21 3-1-3. Adjusting Connectors ···················································· 6-52
5. D Page Table ·································································· 6-21 3-1-4. Connecting the Equipment ············································ 6-53
6. 1A Page Table ································································ 6-22 3-1-5. Alignment Tapes ···························································· 6-54
7. 1B Page Table ································································ 6-22 3-1-6. Input/Output Level and Impedance ······························· 6-54
1-3-2. Initialization of 8, C, 18, 1C Page Data ························· 6-23 3-2. System Control System Adjustments ···························· 6-55
1. Initializing of 8, C, 18, 1C Page Data ··························· 6-23 1. Initialization of 8, A, C, D, E, F,
2. Modification of 8, C, 18, 1C Page Data ························ 6-23 1C,1F Page Data (Non MS model) ······························· 6-55
3. 8 Page Table ··································································· 6-24 2. Touch Panel Adjustment (Non MS model) ··················· 6-55
4. C Page Table ·································································· 6-25 3. Initialization of 8, A, B, C, D, E, F, 18, 19,
5. 18 Page Table ································································· 6-26 1A, 1B, 1C, 1E, 1F Page Data (MS model) ·················· 6-56
6. 1C Page Table ································································ 6-27 4. Touch Panel Adjustment (MS model) ··························· 6-56
1-3-3.Initialization of E, F, 19, 1E, 1F Page Data ··················· 6-28 5. Node Unique ID No. Input ············································ 6-57
1. Initializing of E, F, 19, 1E, 1F Page Data ······················ 6-28 3-3. Servo and RF System Adjustments ······························· 6-59
2. Modification of E, F, 19, 1E, 1F Page Data ··················· 6-28 1. CAP FG Duty Adjustment
3. E Page Table ·································································· 6-29 (VC-376 board (Non MS model))
4. F Page Table ·································································· 6-29 (VC-377 board (MS model)) ········································· 6-59
5. 19 Page Table ································································· 6-31 2. Switching Position Adjustment
6. 1E Page Table ································································ 6-31 (VC-376 board (Non MS model))
7. 1F Page Table ································································ 6-32 (VC-377 board (MS model)) ········································ 6-60
1-4. Camera System Adjustments ········································· 6-33 3. Error Rate Check
1. 36MHz Origin Oscillation Adjustment (VC-376 board (Non MS model))
(VC-376 board (Non MS model)) (VC-377 board (MS model)) ········································· 6-61
(VC-377 board (MS model)) ········································ 6-33 3-1. Preparations Before Adjustments ·································· 6-61
2. Hall Adjustment ····························································· 6-34 3-2. Error Rate Check ··························································· 6-61
DCR-HC21
--2--
Section Title Page
3-4. Video System Adjustments ············································ 6-62 16. Record of Self-diagnosis Check ···································· 6-83
1. S VIDEO OUT Y Level Adjustment
(VC-376 board (Non MS model))
(VC-377 board (MS model)) ········································· 6-62
2. S VIDEO OUT Chroma Level Adjustment * The camera optical axis frame is shown on page 6-84.
(VC-376 board (Non MS model)) The camera color reproduction frame is shown on page
(VC-377 board (MS model)) ········································· 6-63 6-85.
3. VIDEO OUT Level Check
(VC-376 board (Non MS model))
(VC-377 board (MS model)) ········································· 6-64 Note : Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
3-5. Audio System Adjustments (Non MS model) ··············· 6-65 HC22E
1. Playback Level Check ··················································· 6-65 MS model: DCR-HC32/HC32E/HC33/HC33E
2. Overall Level Characteristics Check ····························· 6-65
3. Overall Distortion Check ··············································· 6-66
4. Overall Noise Level Check ············································ 6-66
5. Overall Separation Check ·············································· 6-66
3-6. Audio System Adjustments (MS model) ······················· 6-67
1. Playback Level Check ··················································· 6-67
2. Overall Level Characteristics Check ····························· 6-67
3. Overall Distortion Check ··············································· 6-68
4. Overall Noise Level Check ············································ 6-68
5. Overall Separation Check ·············································· 6-68
6-4. Service Mode ································································· 6-69
4-1. Adjustment Remote Commander ·································· 6-69
1. Using the Adjustment Remote Commander ·················· 6-69
2. Precautions Upon Using the Adjustment
Remote Commander ······················································ 6-69
4-2. Data Process ·································································· 6-70
4-3. Service Mode ································································· 6-71
1. Setting the Test Mode ···················································· 6-71
1-1. Setting the Test Mode (Non MS model) ························ 6-71
1-2. Setting the Test Mode (MS model) ······························· 6-71
2. Emergence Memory Address (Non MS model) ············ 6-71
2-1. Emergency Memory Address (Camera section) ············ 6-71
2-2. EMG Code (Emergency Code) ····································· 6-71
3. Emergence Memory Address (MS model) ···················· 6-72
3-1. Emergency Memory Address (Camera section) ············ 6-72
3-2. EMG Code (Emergency Code) ····································· 6-72
4. Emergence Memory Address (Mechanism section) ······ 6-72
4-1. EMG Code (Emergency Code) ····································· 6-73
4-2. MSW Code ···································································· 6-74
5. Bit Value Discrimination ··············································· 6-75
6. Jack Check (Non MS model) ········································ 6-75
6-1. Jack Check (1) (Handycam station) (DCR-HC22E) ····· 6-75
6-2. Jack Check (2) ······························································· 6-75
7. Jack Check (MS model) ················································ 6-76
7-1. Jack Check (1) (Handycam station) ······························ 6-76
7-2. Jack Check (2) ······························································· 6-76
8. Switch Check (Non MS model) ···································· 6-76
8-1. Switch Check (1) ··························································· 6-76
8-2. Switch Check (2) ··························································· 6-76
8-3. Switch Check (3) ··························································· 6-77
8-4. Switch Check (4) ··························································· 6-77
9. Switch Check (MS model) ············································ 6-78
9-1. Switch Check (1) ··························································· 6-78
9-2. Switch Check (2) ··························································· 6-78
9-3. Switch Check (3) ··························································· 6-78
9-4. Switch Check (4) ··························································· 6-79
10. LED, IR Light Check (Non MS model) ························ 6-80
11. LED, IR Light Check (MS model) ································ 6-80
12. Record of Use Check (1) ··············································· 6-80
13. Record of Use Check (2) (Non MS model) ··················· 6-81
14. Record of Use Check (3) (MS model) ··························· 6-82
15. Record of Use Check (4) ··············································· 6-82
DCR-HC21
--3--
SECTION 6
ADJUSTMENTS
1. Before starting adjustments
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a
board is replaced.
(Machine before starting repair) PC PC (Machine after a board is replaced)
Save the EVR data Download the saved
to a personal computer. data to a machine.
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed
EEPROM to the replaced board.
Remove the EEPROM and install it.
(Former board) (New board)
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
(Machine to be repaired) (Machine to be repaired)
PC
Download the data.
Save the data.
(The same model of the same destination)
After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 or 6-5 for the items to be checked)
DCR-HC21
6-1
1-1. Adjusting items when replacing main parts and boards (Non MS model)
· Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1: When replacing the drum assy or the mechanism deck, reset the data of page: 7, address: A8 to AB to "00". (Refer to "Record of
Use check" of "6-4. SERVICE MODE")
Note 2: Non MS model: DCR-HC17E/HC19E/HC21/HC21E/HC22E
Note 3: DCR-HC32/HC32E/HC33/HC33E model only.
Replaced part
Block replacement Mounted part replacement
(S/H, AGC, A/D converter)
(Drum assembly) (Note 1)
(LCD panel, Touch panel)
(PITCH, YAW sensor)
Adjustment Section Adjustment
(DV signal process)
(Timing generator)
(Back light (EVF))
(Back light LED)
(CCD imager)
(LCD panel)
(LCD drive)
VC-376 board IC3001, X3001
Mechanism deck MD block
Mechanism deck (Note 1)
SI-042 board SE601, 602
Mechanism deck M901
VC-376 board IC3002
VC-376 board IC6001
CD-533 board IC101
PD-237 board IC602
LCD block LCD901
EVF block LCD902
LB-109 board D303
LCD block D901
Lens device
Initialization of A, D page data
Initialization of 8,
A, C, D, E, F, 1C, Initialization of 8, C, 1C page data
1F page data Initialization of E, F, 1F page data
Camera 36MHz origin oscillation adj. z
HALL adj. z
Flange back adj. z z
Optical axis adj. z z
F No. standard data input z z
Mechanical shutter adj. (Note 3) z
Color reproduction adj. z z
Auto white balance standard data input z z
LV standard data input z z
Auto white balance adj. z z
MAX GAIN adj. z z
Steadyshot check z
EVF EVF automatic adj. z z z
LCD LCD automatic adj. z z
V-COM adj. z z
Transmissive mode white balance adj. z z z
Mechanism Tape path adj. z z z
System control Touch panel adj. z
Node uniqe ID No. input
Servo, RF CAP FG duty adj. z z
Switching position adj. z z z
Error rate check z z z z
Video S VIDEO OUT Y level adj. z
S VIDEO OUT chroma level adj. z
Table 6-1-1 (1)
DCR-HC21
6-2
· Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Replaced part
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE)
(EEP ROM)
Adjustment Section Adjustment
RadarW
VC-376 board IC8602
CD-533 board
VC-376 board
LB-109 board
PD-237 board
SI-042 board
Supporting
Initialization of A, D page data z z
Initialization of 8,
A, C, D, E, F, 1C, Initialization of 8, C, 1C page data z z
1F page data Initialization of E, F, 1F page data z z
Camera 36MHz origin oscillation adj. z z
HALL adj. z z z
Flange back adj. z z z z
Optical axis adj. z z z
F No.standard data input z z z z
Mechanical shutter adj. (Note 3) z z z
Color reproduction adj. z z z
Auto white balance standard data input z z z z
LV standard data input z z z z
Auto white balance adj. z z z z
MAX GAIN adj. z z z z
Steadyshot check z z z z
EVF EVF automatic adj. z z z
LCD LCD automatic adj. z z z z
V-COM adj. z z z
Transmissive mode white balance adj. z z z
Mechanism Tape path adj.
System control Touch panel adj. z z
Node uniqe ID No. input z z
Servo, RF CAP FG duty adj. z z z
Switching position adj. z z z
Error rate check z z z
Video S VIDEO OUT Y level adj. z z
S VIDEO OUT chroma level adj. z z
Table 6-1-1 (2)
DCR-HC21
6-3
1-2. Adjusting items when replacing main parts and boards (MS model)
· Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1: When replacing the drum assy or the mechanism deck, reset the data of page: 7, address: A8 to AB to "00". (Refer to "Record of
Use check" of "6-4. SERVICE MODE")
Note 2: MS model: DCR-HC32/HC32E/HC33/HC33E
Replaced part
Block replacement Mounted part replacement
(Video/Audio DSP, D/A converter etc)
(S/H, AGC, A/D converter)
(Drum assembly) (Note 1)
(LCD panel, Touch panel)
(PITCH, YAW sensor)
Adjustment Section Adjustment
(DV signal process)
(Timing generator)
(Back light (EVF))
(Back light LED)
(Video IN/OUT)
(REC/PB AMP)
(HI/DS control)
(CCD imager)
(LCD panel)
(LCD drive)
(EVF drive)
VC-377 board IC3101, X3101
Mechanism deck MD block
Mechanism deck (Note 1)
SI-042 board SE601, 602
Mechanism deck M901
VC-377 board IC3102
VC-377 board IC4001
VC-377 board IC4201
VC-377 board IC4301
VC-377 board IC4401
VC-377 board IC5102
VC-377 board IC7001
CD-533 board IC101
PD-237 board IC602
LCD block LCD901
EVF block LCD902
LB-109 board D303
LCD block D901
Lens device
Initialization of 8, Initialization of A, B, D, 1A, 1B page data
A, B, C, D, E, F, 18,
Initialization of 8, C, 18, 1C page data
19, 1A, 1B, 1C, 1E,
1F page data Initialization of E, F, 19, 1E, 1F page data
Camera 36MHz origin oscillation adj. z z
HALL adj. z
Flange back adj. z z
Optical axis adj. z z
F No. standard data input z z
Mechanical shutter adj. z
Color reproduction adj. z z
Auto white balance standard data input z z
LV standard data input z z
Auto white balance adj. z z
MAX GAIN adj. z z
Steadyshot check z
EVF EVF automatic adj. z z z
LCD LCD automatic adj. z z
V-COM adj. z z
Transmissive mode white balance adj. z z z
Mechanism Tape path adj. z z z
System control Touch panel adj. z
Node uniqe ID No. input
Servo, RF CAP FG duty adj. z z
Switching position adj. z z z
Error rate check z z z z z
Video S VIDEO OUT Y level adj. z z
S VIDEO OUT chroma level adj. z z
Table 6-1-2 (1)
DCR-HC21
6-4
· Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Note 3: IC5202 (Flash memory) on
Replaced part
the VC-377 board cannot be
replaced.
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE)
(EEP ROM)
(EEP ROM)
Adjustment Section Adjustment
RadarW
VC-377 board IC5302
VC-377 board IC5101
CD-533 board
VC-377 board
LB-109 board
PD-237 board
SI-042 board
Supporting
Initialization of 8, Initialization of A, B, D, 1A, 1B page data z z
A, B, C, D, E, F, 18,
Initialization of 8, C, 18, 1C page data z z
19, 1A, 1B, 1C, 1E,
1F page data Initialization of E, F, 19, 1E, 1F page data z z
Camera 36MHz origin oscillation adj. z z
HALL adj. z z z
Flange back adj. z z z z
Optical axis adj. z z z
F No.standard data input z z z z
Mechanical shutter adj. z z z
Color reproduction adj. z z z z
Auto white balance standard data input z z z z
LV standard data input z z z z
Auto white balance adj. z z z z
MAX GAIN adj. z z z z
Steadyshot check z z z z
EVF EVF automatic adj. z z z z
LCD LCD automatic adj. z z z z
V-COM adj. z z z
Transmissive mode white balance adj. z z z
Mechanism Tape path adj.
System control Touch panel adj. z z
Node uniqe ID No. input z z
Servo, RF CAP FG duty adj. z z z
Switching position adj. z z z
Error rate check z z z
Video S VIDEO OUT Y level adj. z z
S VIDEO OUT chroma level adj. z z
Table 6-1-2 (2)
DCR-HC21
6-5
6-1. CAMERA SECTION ADJUSTMENTS
1-1. PREPARATIONS BEFORE ADJUSTMENTS (CAMERA SECTION)
1-1-1. List of Service Tools
· Oscilloscope · Color monitor · Vectorscope
· AC power adapter · Frequency counter
J-1 J-2 J-3
Color bar chart
Pattern box PTB-450
Adjustment remote
J-6082-200-A
commander For PTB-450:
or
J-6082-053-B J-6020-250-A
Small pattern box
PTB-1450
For PTB-1450:
J-6082-557-A
J-6082-559-A
J-4 J-5 J-6
Clear chart
For PTB-450: Flange back
J-6080-621-A Minipattern box adjustment jig
J-6082-353-B J-6082-563-A
For PTB-1450:
J-6082-560-A
J-7 J-8 J-9
ND filter 1.0
J-6080-808-A
Filter for color
Siemens star chart temperature correction ND filter 0.4
J-6080-875-A (C14) J-6080-806-A
J-6080-058-A ND filter 0.1
J-6080-807-A
J-10 J-11 J-12
A
A: CPC-15
J-6082-564-A
Back ground paper Camera table
B: I/F unit for
J-2501-130-A J-6082-384-A
LANC control
B J-6082-521-A
Fig. 6-1-1
DCR-HC21
6-6
1-1-2. Preparations
Pattern box
Note: Before perform the adjustment, check that the data of page:
0, address: 10 is "00".
If not, select page: 0, address: 10, and set data "00".
1) Connect the equipment for adjustments according to Fig. 6-1-3.
L
Front of the lens
L = 1m (PTB-450)
L = 40cm (PTB-1450)
Fig. 6-1-2
(Non MS model) (MS model)
A/V OUT jack LANC jack A/V jack LANC jack
Adjustment remote commander
(RM-95)
S Video
(Black)
Except DCR-HC22E
Color monitor Vectorscope
Video
(yellow) Terminated
AC adaptor AC IN 75
Audio L
(White)
To DC IN jack
Note: Non MS model: DCR-HC17E/HC19E/HC21/HC21E/HC22E Audio R
MS model: DCR-HC32/HC32E/HC33/HC33E (Red)
Fig. 6-1-3
DCR-HC21
6-7
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
Note : Non MS model: DCR-HC17E/HC19E/HC21/HC21E/HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
(Non MS model)
1. POWER switch (SS10300 block) ......................... CAMERA 9. D ZOOM (MENU setting) ............................................. OFF
2. LENS COVER switch (Lens block) ........................... OPEN 10. WIDE SEL (MENU setting) ............................................. 4:3
3. NIGHTSHOT PLUS switch (Lens block) ..................... OFF 11. STEADY SHOT (MENU setting) .................................. OFF
4. BACK LIGHT (FP-187 flexible) ................................... OFF 12. P EFFECT (MENU setting) ........................................... OFF
5. PROGRAM AE (MENU setting) ................................ AUTO 13. DEMO MODE (MENU setting) .................................... OFF
6. EXPOSURE (MENU setting) ..................................... AUTO
7. WHITE BAL (MENU setting) .................................... AUTO
8. FOCUS (MENU setting) ...................................... MANUAL
(MS model)
1. POWER switch (SS10300 block) .............. CAMERA-TAPE 9. COLOR SLOW S (MENU setting) ................................ OFF
2. LENS COVER switch (Lens block) ........................... OPEN 10. DIGITAL ZOOM (MENU setting) ................................ OFF
3. NIGHTSHOT PLUS switch (Lens block) ..................... OFF 11. WIDE SELECT (MENU setting) ..................................... 4:3
4. BACK LIGHT (FP-187 flexible) ................................... OFF 12. STEADY SHOT (MENU setting) .................................. OFF
5. PROGRAM AE (MENU setting) ................................ AUTO 13. D EFFECT (MENU setting) .......................................... OFF
6. EXPOSURE (MENU setting) ..................................... AUTO 14. PICT EFFECT (MENU setting) .................................... OFF
7. WHITE BAL. (MENU setting) ................................... AUTO 15. DEMO MODE (MENU setting) .................................... OFF
8. FOCUS (MENU setting) ...................................... MANUAL
2. Order of Adjustments
Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame)
Electronic beam scanning frame
H
Yellow
Magenta
White
Cyan
Green
C C=D D
Red
Blue
Magenta
Yellow
Green
White
Cyan
Blue
Red
CRT picture frame
V
A B A=B B A
Fig. b (monitor TV picture)
Fig. a Enlargement
(VIDEO terminal of A/V jack
output waveform)
Difference in level
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a and
B A the monitor TV display shown in Fig. b.
Fig. 6-1-4
DCR-HC21
6-8
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2) Mixed color compensation chart (Color reproduction White
adjustment frame) 841 mm
Remove the color bar chart from the pattern box and insert a
Black
mixed color compensation chart in its place. (Do not perform
zoom operations during this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm × 841
1189 mm
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.
Fig. 6-1-5
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
DCR-HC21
6-9
4. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment.
If it is not available, prepare the flash adjustment box as given
below;
1) Provide woody board A, B and C of 15 mm thickness.
woody board A (2) woody board B (2) woody board C (1)
400 mm 370 mm 700 mm
513 mm 513 mm 700 mm
730 mm 700 mm
Fig. 6-1-6
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper
side of woody board A, B and C are internal. (Fig. 6-1-7)
woody board A
woody board B
woody board A
woody board B
woody board C
Fig. 6-1-7
DCR-HC21
6-10
1-2. INITIALIZATION OF 8, A, C, D, E, F, 1C, 1F
PAGE DATA (Non MS model) 2. Modification of A, D Page Data
Note 1: If reading/writing data on pages 1C, 1F, set data: 01 to If the A, D page data has been initialized, change the data of
page: 0, address: 10, and then select pages C, F. By this the"Fixed data-2" address shown in the following table by manual
data setting, the pages 1C, 1F can be selected. input.
After the data reading/writing finished, return the data
on page: 0, address: 10 to "00". Modifying method:
Note 2: Non MS model: DCR-HC17E/HC19E/HC21/HC21E/ 1) Before changing the data, select page: 0, address: 01, and set
HC22E data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
1-2-1. Initialization of A, D Page Data the data built in the same model.
Note: Check that the data of page: 0, address: 10 is "00". Note 1: If copy the data built in the different model, the
camcorder may not operate.
1. Initializing of A, D Page Data 3) When changing the data, press the PAUSE button of the ad-
Note 1: If "Initialization of Pages A, D" is executed, all data on justment remote commander each time when setting new data
pages A, D are initialized. to write the data in the non-volatile memory.
Note 2: If the A, D page data has been initialized, the following 4) Check that the data of adjustment addresses is the initial value.
adjustments need to be performed again. If not, change the data to the initial value.
1) Modification of A, D page data
2) Touch panel adjustment Processing after completing modification A, D page data:
Note 3: NTSC model: DCR-HC21/HC32/HC33
PAL model: DCR-HC17E/HC19E/HC21E/HC22E/ Order P