Text preview for : CT_2088_1488_BL6X_XAP_Chassis_K15A_H_Service_manual.pdf part of samsung ct-2088bl6x/xbm service manual tv samsung ct-2088bl6x



Back to : CT_2088_1488_BL6X_XAP_Cha | Home

COLOR TELEVISION RECEIVER
Chassis : Model: K15A (H) CT2088BL6X/XAP CT1488BL6X/XAP

COLOR TELEVISION RECEIVER

CONTENTS
1. Precautions 2. Specifications 3. Alignment and Adjustments 4. Troubleshooting 5. Exploded Views and Parts List 6. Electrical Parts List

G G UN UN MS MS SA SA

7. Block Diagram 8. Wiring Diagrams 9. Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd. APR. 2000
Printed in Korea 3K15A-8801

Precautions

1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 3-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

LEAKAGE CURRENT TESTER

(READING SHOULD NOT BE ABOVE 0.5mA)

EARTH GROUND

Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the X­ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Samsung Electronics

1-1

Precautions

1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

1-2

Samsung Electronics

Precautions

1-2 Servicing Precautions
Warning 1 : First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last. 9. When some parts inside the optical engine (except lamp) are damaged, replace the whole optical engine.

Samsung Electronics

1-3

Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

1-4

Samsung Electronics

Specifications

2. Specifications
2-1 Specifications

Television System

14" / 20" / 21" NTSC COLOR TV SIGNAL

Picture Tube

A34KQV42X / A48KRD82X (H) / A51KQJ63X

Power Requirement Operating System Tuning Ranges Antenna Input Impedance Intermediate Frequency

AC 120V, 60Hz /AC 100 ~ 240, 50Hz, 60Hz REMOCON SYSTEM (SZM370TH) VHF CH : 2-13, UHF CH : 14-69, CABLE CH : 1,14-125 75 ohm UNBALANCED TYPE FOR VHF/UHF PICTURE 45.75MHz, SOUND 41.25MHz, COLOR SUB CARRIER 42.17MHz

Speaker Impedance

Dual : 8 ohm 6W x 2

Samsung Electronics

2-1

MEMO

2-2

Samsung Electronics

Alignment and Adjustments

3. Alignment and Adjustments
3-1 Service Mode Adjustments
3-1-1 Service Mode Menus
Since there are no VRs in the K15A chassis, all adjustments after parts replacement must be done in the Service Mode. Service Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced.

3-1-2 Entering the Service Mode
Press the following transmitter keys while in STAND-BY mode: MUTE-->1-->8-->2-->POWER "Factory Mode Menu" is displayed ADJUSTMENT PATTERN OPTION RESET <---selected (violet)

Change the data with "Volume +, - " keys. VCO 71

Enter Service Mode using the Volume +,- keys. Service Mode Menu: AGC VCO SBT SCT SCR STT GG BG XX XX XX XX XX XXX XXX XXX RC XXX GC XXX BC XX VA XX VS XX HS XX SS XX SVC : MUTE

Return to the Service mode by pressing MENU. AGC VCO SBT SCT SCR STT GG BG XX XX XX XX XX XXX XXX XXX XXX RC XXX GC XX BC VA XX VS XX HS XX SS XX SVC : MUTE

Select a mode to be adjusted, using the channel down key. Example: VCO. AGC VCO SBT SCT SCR STT GG BG XX XX XX XX XX XXX XXX XXX RC XXX GC XXX BC XX VA XX VS XX HS XX SS XX SVC : MUTE

Return to the Factory mode via the MENU key. ADJUSTMENT PATTERN OPTION RESET Press POWER to enter the Stand-by mode.

Samsung Electronics

3-1

Alignment and Adjustments

3-1-3 Adjustment in Option Mode
This adjustment is necessary whenever the EEPROM is replaced. Input data (as marked on the back cabinet). ADJUSTMENT PATTERN OPTION RESET Select "SET OPTION" by pressing the Channel w key twice. ADJUSTMENT PATTERN OPTION RESET Press the Volume +, - keys to enter the set Option mode. BYTE 0 : 0 0 BYTE 1 : 0 4 Press MENU to go back to the factory mode. ADJUSTMENT PATTERN OPTION RESET

3-1-4 Service Mode Adjustments

ADJUSTMENT PATTERN OPTION RESET 1. The Pattern Adjustment is done only in the factory. Do not attempt to readjust it. 2. Refer to 3-2 for other adjustments. 3. Set OPTION data.

3-1-5 Service Mode Adjustment Ratings
No Item Function Range 0~63 0~127 0~63 0~27 0~27 0~255 0~255 0~255 Initalized MICOM Data 50 63 48 13 7 0 0 0

1 AGC RF AGC Adjustment 2 VCO PIF VCO Adjustment 3 SCT SUB-CONTRAST Adjustment 4 SCR SUB-COLOR Adjustment 5 STT SUB-TINT Adjustment 6 RC 7 GC RED-CUT OFF Adjustment GREEN-CUT OFF Adjustment BLUE-CUT OFF Adjustment

Select RESET with channel ADJUSTMENT PATTERN OPTION RESET

w key.

8 BC

9 SVC Input a Horiz line pattern 10 GG 11 BG GREEN-GAIN Adjustment BLUE-GAIN Adjustment 0~255 0~255 0~63 0~63 0 0~31 0~31 127 127 31 39 0 15 4

12 SBT SUB-BRIGHTNESS Adjustment 13 VA VERTICAL SIZE Adjustment VERTICAL CENTER Adjustment HORIZONTAL Phase Adjustment SUB-SHARPNESS Adjustment

Press volume + key. POWER OFF

14 VS 15 HS 16 SS

Note : The initial MICOM data values take effect when IC902 is replaced.

3-2

Samsung Electronics

Alignment and Adjustments

3-2 Alignment and Adjustment
3-2-1 General Alignment Instructions
1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as picture height, focus and a horizontal and vertical sync. 2. Observe the picture and check for good back and white details. There should be no objectionable color shading: If color shading is present, demagnetize the receiver. If color shading persists, perform purity and convergence adjustments described below. 3. To protect against shock hazard, use an isolation transformer.

3-2-5 IC902 Replacement
1. When IC902 is replaced, all values are reset to "Initialized MICOM Data" and readjustment is necessary. 2. Press the POWER button 10 seconds after plug-in. 3. To enter the Service Mode, refer to Fig. 3-1 (Service Mode Adjustment).

3-2-6 PIF VCO Adjustment
1. Use a Pattern Generator or an off-air signal. 2. Open pin 11 of Micom (IC901) or one side of lead pin for R237. 3. Adjust VCO in the service mode to set IC101 Pin 44 (AFT) to 2.5V ± 0.4V. 4. Connect the opened site.

3-2-2 Power Supply Check
Check the following: A: Power plug is connected; "Stand-by" mode B: Power On when "Power ON" button is pressed C: Power On by FBT Each supply is marked on its lead-in wire. ( )

3-2-3 Focus Adjustment
Adjust the focus control on the FBT for well defined scanning lines.

3-2-7 RF-AGC Adjustment
1. 2. 3. 4. Input a PHILLIPS pattern. Set the input signal to 60 dB. Enter into the AGC in the service mode. Adjust AGC until color bar noise disappears.

3-2-4 Fail Safe Circuit Check (FS) (OPTION)
1. The failsafe check must be the final step in servicing. 2. Turn the power switch ON and adjust customer controls for normal operation. 3. Temporarily short pin X to pin R on the main board (RX06, RX04) with a jumper wire. Raster will disappear. 4. The TV must remain in this state even after removing the jumper wire. This shows that the failsafe circuit is working properly. 5. To recover picture and sound, temporarily turn off the TV and allow the failsafe circuit more than 30 seconds to reset. Then switch power ON to produce normal picture and sound.

Samsung Electronics

3-3

Alignment and Adjustments

3-2-8 Sub-Contrast Adjustment
1. Input a gray scale pattern. Use a pattern generator (PM5518). 2. 3. 4. Short D208 to switch off the ABL feed-back. Check CN201 R-OUT with an oscilloscope. Set RC, BC, GC data to 0 in the Service Mode.

3-2-10 Sub-Color Adjustment
1. Do sub-color adjustment after the SubContrast and Sub-Tint adjustments. 2. D208 should still be shorted. The ABL should still be switched OFF. 3. Input a color bar pattern. Use a pattern generator (PM5518). 4. Check CN201 R-OUT (use an oscilloscope). 5. Ensure that the RC, GC and BC data are 0. BG are 140 and GG should be 90. 6. Adjust SCR to 2.4 ± 0.1Vp-p (black and red levels).
+ 2.5V_ 0.1Vpp

5. Adjust SCT to 2.40 ± 0.1Vp-p

7. Remove the short across D208 and restore ABL.

6. Remove the short across D208 and restore ABL.

+ 2.4V _ 0.1Vpp

3-2-9 Sub-Tint Adjustment
1. 2. Input a rainbow pattern. Check CN201 B-OUT with an oscilloscope.

3. Adjust STT in the service mode until the 6th peak is the highest and the 5th and 7th peaks have equal heights.

3 1 2

4

5

6 7 8 9 10

3-4

Samsung Electronics

Alignment and Adjustments

3-2-11 White Balance Adjustment
3-2-11 (A) LOW-LIGHT ADJUSTMENTS
1. Input either a lion head or "pure white" color pattern. 2. Operate the receiver for 30 minutes. 3. Check the data in the service mode: RC, GC, BC are 0 and SB is 16; Steps BG are 90 and GG are 140. 4. Enter the horizontal line mode by pressing the MUTE key. 5. Adjust the screen VR on the FBT until a dim colored line (red,green or blue) appears on the screen. 6. After pressing the MUTE key, go to RC,BC or GC with channel , w keys. After putting a dim colored line (red, green or blue) in the horizontal line with MUTE key, adjust color with volume ,w keys. 7. Exit the horizontal line via the MUTE key.

3-2-13 Vertical Size Adjustment
1. Input a lion head pattern. 2. After the vertical center adjustment, enter into the service mode. 3. Adjust VA so that the each top and bottom of the screen is 4.0. If the top and bottom values are different, adjust VA so that the sum of the two values is 8.0.

3-2-14 Horizontal Size Adjustment
1. Receive a lion head pattern. 2. Enter into the service mode. 3. Adjust HS to symmetrized right and left.

3-2-11 (B) HIGH-LIGHT ADJUSTMENTS
1. Input a high-light pattern 2. Adjust GG,BG in the Service Mode. 3. Recheck in low light.

3-2-12 Sub-Brightness Adjustment
1. Input a Toshiba pattern. 2. Warm up the receiver for 10 minutes. 3. Enter the Service Mode and set SB to the point where the 5th point is brighter in the gray scale.

Samsung Electronics

w

3-2-15 When CRT Is Replaced
Do the following adjustments after the basic purity and convergence adjustments. 1. White Balance 2. Sub-brightness 3. Vertical Size 4. Horizontal Size 5. Fail safe (should be the final step).

w

W 5 4 3 2 1

3-5

3-3 Option Byte Table
Micom : SZM370TH
Note: The option bytes are adjusted in the Service mode. FUNCTION 0 D7 D6 WIDE AFT AUTO POWER ON D4 AUTO D3 SOUND MUTE D2 TV/Video AUTO POWER OFF (during no signal) TV/Video (during no signal) Video Only Power Off (after 15 minute) during no signal AIR/STD/HRC/AFN 1 for army NT Only REMARK 0 Sound Mute No Sound Mute Not Used Analog (Tuner Input) 1 Used Digital (1 Chip Input) REMARK

BYTE:0

NAME

D5

Not Used

Used

D1

Not Used

D0

CATV

AIR/STD/HRC/IRC

FUNCTION BYTE:1 D7 D6 D5 D4 D3 D2 D1 D0 TURBO MTS V-CHIP No Turbo function No MTS function No V-CHIP function Turbo function exists MTS function exists V-CHIP function exists NAME 0

3-6

Samsung Electronics

Troubleshooting

4. Troubleshooting
4-1 No Power

No Power

OFF

Check LED when AC code is plugged.

ON Check IC802. Abnormal

Abnormal

Check Fuse.

Normal

Check/Replace IC802, R812, D856.

Check and Replace D801S ~ D804S

Check IC801S Pin 1 Oscillation. Abnormal

Abnormal (0 ~ 15V)

Check IC801S Pin 3 B+.

Check/Replace D806, Q401, Q801, D802, D814* Abnormal (0V)

Normal (15~20V)

Check IC801S* Pin 4 Voltage

Normal (0.5 ~ 3V)

Check/Replace PC802

Check/Replace DZ802, D806

Samsung Electronics

4-1

4-2
NO Sound Normal Check Connector CN604 and CN703. Abnormal Abnormal Check Waveform of IC601 pin 4,12 Normal Check CN604 and CN703 Connector Soldering and A/V PCB Check Waveform of ICA02 pin 6,9 Abnormal Normal Check Waveform of Abnormal OK OK Normal Check Waveform of IC201 pin 52 Abnormal Check Voltage of IC601 pin 3,13 Abnormal Normal(approx.12.5V) Replace IC201 or Check power 9V Line Voltage Check SIF(L201) Check power 12.5V Line Voltage Replace IC601

Troubleshooting

4-2 No Sound

Normal

Normal

Check Waveform of ICA02 pin 4,5

Abnormal

OK

OK

Volum Up

N.G

Replace ICA02 or Check power 9V Line Voltage

Samsung Electronics

Troubleshooting

4-3 Horizontal Line Appears

Single Horizontal Line

Normal (24V)

Check 24V-C Voltage.

Abnormal

Abnormal

Check Waveform of IC201S Pins 22,24.

Check FBT Pin 2 (24V) Oscillation. Normal

NG

Check Whether O.K a horizontal line appears in Normal the service mode.. NG Check/Replace IC201S. Check/Replace IC301.

Check R409 Open. Open Check/Replace R409.

Check/Replace FBT.

Samsung Electronics

4-3

Troubleshooting

4-4 No Signal
No Signal

Abnormal

Check each tuner terminal voltage.

Normal

Check voltage line.

Abnormal

Check tuner SCL,SDA waveform.

Normal

Check Micom IC901.

Normal

Check tuner IF terminal waveform. Abnormal Replace tuner.

Check IC201S Pins 7,8 waveform.
Check IC201S Pin 41 waveform level.

Normal
Check whether AGC and AFTadjustment are normal in the service mode.

Normal (2Vp-p)
Check IC201 Pin 43 waveform level.

Abnormal

Normal Abnormal
Check IC201S Pin 47 waveform level. Readjust AGC and AFT.

Normal (1Vp-p)
Check IC201S Pins 19,20, 21 waveform level.

Abnormal

Normal (2Vp-p)
Check IC201S Pin 37 waveform level.

Normal (3~5Vp-p)
Replace IC201S. Check CRT PCB (180V) and heater Voltages.

Normal (1Vp-p)

4-4

Samsung Electronics

Exploded Views & Parts List

5. Exploded Views & Parts List
5-1 CT2088BL6X/XAP

No
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 2 2-1 2-2 2-3 3 3-1 3-2 4

Code No
AA91-00283B AA64-00704B AA64-00703D AA61-60003J AA64-00705B AA64-70123B AA63-00204B AA63-00205B AA63-00226B AA63-00202C AA61-40113A AA65-30105A AA64-00702B 6003-001026 3001-001088 6003-001026 AA03-10029Z AA65-30107A AA60-10050R 3704-001105 AA64-00701C 6003-001026 AA42-10001V AA39-10006X

Description
ASSY CABINET FRONT WINDOW REMOCON KNOB POWER SPRING-CS INDICATOR LED BADGE-BRAND GRILLE-WOOFER,L GRILLE-WOOFER,R COVER-TOP,LATIN COVER-CONTROL STOPPER-PCB CLAMP-WIRE KNOB CONTROL SCREW-TAPTITE SPEAKER SCREW-TAPTITE CRT-COLOR CLAMP-D,COIL SCREW-ASSY SOCKET-CRT CABINET BACK SCREW-TAPTITE ANT-ROD POWER-CORD

Specification
;-,20S4,(SPK)SV704 EPG ;-,20S4,-,PC,V0,VIOLET,-" ;-,20S4,T/S NO-SILK,ABS,HB,G36 ;-,SUS304,0.5,OD6,H12,N7,-,-,;-,20S4,-,ACRYL,-,CLR,;AL,R2000,SILVER,L=50,SAMSUNG ;-,20S4,-,SECC,T0.5,SV704 ;-,20S4,-,SECC,T0.5,SV704 ;-,20S4,T/SOUND,ABS,LG TR ;-,20S4,GD906P EPG NT,HIPS, ;501H,HIPS,NTR,HB,-,;NYLON 66,V2,NTR,15MM,ALL MODE ;-,20S4,-,ABS,HB,G3676 ;RH,+,B,M4,L15,ZPC(BLK),SWR ;5W,8ohm,90dB,250Hz+-50Hz ;RH,+,B,M4,L15,ZPC(BLK),SWR ;-,A48KRD82X(HB),+380mG,20,90d ;NYLON 66,V2,NTR,-,20~22 INC ;WC,HH,+,M5,L31.5,SWRCH18A,ZPC ;11P,20PI,26.5PI,NI,;-,20S4,-,HIPS,HB,BLK,-,;RH,+,B,M4,L15,ZPC(BLK),SWR ;-,3S,620mm,BRN,UL/CSA ;-,KKP419C,KLCE-2F,2.286MT,3P,

Q'ty
1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 12 1 4 4 1 1 6 1 1

Remark

Samsung Electronics

5-1

MEMO

5-2

Samsung Electronics

Electrical Parts List

6. Electrical Parts List
6-1 CT1488BL6X/XAP (CT1488BL6X/XAP and CT2088BL6X/XAP Dissimilar parts)
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

ASSY PCB MAIN(OPT)
* AA94-01968CASSY PCB MAIN(OPT);CT-14S4,K15A,KOREA,C216 C301 C305 C602 CN501 CN604 CN705 CR401S CR402S CR403S CS602 JAW03 JAW04 LC801S LR401S R204 R205 R206 R214 R226 R303 R304 R305 R306 R307 R308 R309 R404 R411 R412 R413 R518 R518A R606 R607 RM01 RM02 RS604 RS605 RU10 T444S V999S 2201-000354 2301-000020 2305-000427 2201-000292 AA39-20109D 3711-002643 3711-002641 2301-001337 2201-000406 2306-000171 2201-000292 3812-000219 3812-000219 AA27-20003U AA27-30003R 2001-000995 2001-000995 2001-000995 2001-000290 2001-000397 2001-000864 2003-001036 2001-000660 2001-001000 2001-000679 2001-000633 2003-000649 2001-000020 2004-001377 2004-001377 2001-001037 2008-000266 2008-001015 2001-000613 2001-000890 2002-001006 2002-001006 2001-000613 2001-000890 2001-000780 AA26-30005S 3704-001112 C-CERAMIC,DISC;0.02nF,5%,50V,NP0,TP,5x3,5 C-FILM,PEF;27nF,5%,100V,TP,7.3x4x12.5mm,5 C-FILM,MPEF;47nF,5%,100V,TP,7.5x12.5x3.5,5 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,5 LEAD CONNECTOR-ASSY;-,YBNH025-08,S,8P,300,1007#26 CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGHT,SN CONNECTOR-HEADER;BOX,10P,1R,2.54mm,STRAIGHT,Sn C-FILM,MPE-PPF;4.3nF,5%,1.6kV,TP,28.5x16x9mm,20 C-CERAMIC,DISC;0.27nF,10%,2kV,Y5P,TP,6.3x5,7.5 C-FILM,MPPF;270nF,5%,250V,TP,21.5x12.5mm,7 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,5 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm COIL-DEGAUSSING;-,14,16.4ohm,75T,890mm,D COIL-LINEARLITY;-,220uH,YL10x10,0.35mm,23x13mm R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL OXIDE(S);3.3ohm,5%,2W,AF,TP,3.9x10mm R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;82KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;36KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;30KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL OXIDE(S);330ohm,5%,1W,AF,TP,3.3x9mm R-CARBON(S);22OHM,5%,1/2W,AA,TP,2.4X6.4MM R-METAL(S);120Kohm,1%,1/2W,AA,TP,2.4x6.4m R-METAL(S);120Kohm,1%,1/2W,AA,TP,2.4x6.4m R-CARBON(S);0.39OHM,5%,1/2W,AA,TP,2.4X6.4MM R-FUSIBLE(S);1ohm,5%,2W,AF,TP,3.9x10mm R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x9mm R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x9mm R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM TRANS-FLYBACK;-,FSV-14A004(S),14,125V SOCKET-CRT;8P,12PI,22.5PI,NI,-

LED PA+CF SPRING WRMC

AA64-00755B AA60-10002A AA61-60003J AA64-00754B

INDICATOR LED;-,14S4,-,ACRYL,-,CLR,SCREW-TAPPING;RH,+,M4,L12,ZPC(YEL),-,OD14 SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,WINDOW REMOCON;-,14S4,-,PC,V0,VIOLET,-

ASSY-CRT
* AA94-50015E ASSY-CRT;A34KQV42X(B),+380mG,14,BARE,C CRT DY MGNT AA03-10001Z CRT-COLOR;-,A34KQV42X(B),+380MG,14,90DE AA27-50004X DEFLECTION-YOKE; AA27-00001A MAGNET-CONVERGENCE;-,JH225-06A,22.5MM

ASSY-PCB,A/V FRONT
* AA95-00591A ASSY-PCB,A/V FRONT;-,CT1488BL6,K15A,-,-,LEAD PCBF AA39-20067A LEAD CONNECTOR-ASSY;-,YBNH025-10,67096-010,10P,300 AA41-00250A PCB-FRONT A/V;K15A,1L,FR-1,245x245x1.6T,24A,MC-H/VC,51x27

ASSY SPEAKER
* AA96-00321A ASSY SPEAKER;-,8ohm,6W,001034/00320A,350/550 AHDRS LEADC SPK AA91-00320A ASSY HOLDER SPK;-,-,PIEZO ASSY,-,SILVER CAP,CT-14S4 AA39-00105A LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,YSH25004,REC,35155-0200,4P,350/550/100mm,1007#22 3001-001034 SPEAKER;6W,8ohm,90dB,140Hz

ASSY CABINET FRONT
* AA91-00317A ASSY CABINET FRONT;-,14S4,(SPK)SV704 EPG B2,HB,GRAY * AA90-00268A ASSY CABINET;14S4,CT1488BL6X/XAP BACK BADGE CB+CF CMPD CRT+CF CVR CVRT FRONT GRILLE GRILLE ID+CF KNOBC KNOBP AA64-00751B AA64-70127F 6002-000514 AA65-30106A AA60-10050Q AA63-00215B AA63-00227B AA64-00750B AA63-00218B AA63-00219B 6003-001026 AA64-00752B AA64-00753B CABINET BACK;-,14S4,-,HIPS,HB,BLK,-,BADGE-BRAND;AL,SAMSUNG,SILVER,L40,R800,NEW SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWRCH18 CLAMP-D,COIL;NYLON 66,V2,NTR,-,14 INCH,SCREW-ASSY;WC,HH,+,M5,L26.5,SWRCH18A,ZPC( COVER-CONTROL,A;-,14S4,GD906P EPG NT,HIPS,HB,GRAY,COVER-TOP,LATIN;-,14S4,DG703P,ABS,LG TR558,CLR,-,CABINET FRONT;-,14S4,SV704P EPG BIO2000,HIPS,HB,GRAY,-,GRILLE-WOOFER,L;-,14S4,SV704G,SECC,T0.5,-,GRILLE-WOOFER,R;-,14S4,SV704G,SECC,T0.5,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWRCH18 KNOB CONTROL;-,14S4,-,ABS,HB,G3676 KNOB POWER;-,14S4,NT NO-SILK,ABS,HB,G3676

Samsung Electronics

6-1

Electrical Parts List

6-2 CT2088BL6X/XAP
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

ASSY PCB MAIN(OPT)
* AA94-01968BASSY PCB MAIN(OPT);CT20S4Z6X/XAP,K15A-1, C101 C102 C104 C108 C110 C151 C153 C201 C202 C203 C204 C205 C206 C207 C209 C210 C211 C212 C213 C214 C215 C218 C219 C220 C221 C222 C225 C226 C227 C229 C230 C231 C232 C234 C235 C236 C237 C301 C302 C303 C304 C305 C306 C308 C309 C310 C311 C312 C313 C401 C405 C406 C407 C408 C409 C410 C411 C412 C413 C444 C445 C501 C502 C503 C505 C601 C602 C603 2202-000127 2401-000660 2202-000127 2401-000480 2401-002594 2202-000127 2202-000127 2201-000292 2401-001333 2401-002144 2301-000188 2401-001333 2305-001011 2401-001333 2202-002037 2202-002037 2202-002037 2201-000982 2201-000193 2401-000660 2401-001840 2301-000395 2401-000603 2401-000480 2401-002462 2305-000665 2401-000480 2401-000603 2305-000665 2202-000127 2202-002037 2401-002144 2401-002144 2301-000232 2202-000279 2202-000127 2202-000791 2301-000016 2201-000556 2202-000127 2401-000553 2305-000149 2401-002458 2301-000310 2401-000365 2401-000480 2401-001333 2401-000553 2305-000470 2301-000224 2305-000704 2201-000556 2401-001429 2201-000556 2401-001998 2301-000224 2201-000556 2401-000927 2401-002268 2201-000441 2201-000441 2202-000863 2202-000862 2202-000825 2201-002063 2401-001998 2301-000383 2401-000603 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-AL;2.2uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;220uF,20%,16V,GP,TP,8x11.5,5 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5, C-AL;470nF,20%,50V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-FILM,PEF;1nF,5%,100V,TP,10.5x12.5x6.5, C-AL;470nF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;22nF,5%,100V,TP,3.5x12.5x7.5 C-AL;470nF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,DISC;10nF,+80-20%,50V,Y5V,TP,4 C-CERAMIC,DISC;0.01nF,0.25pF,50V,NP0,TP, C-AL;2.2uF,20%,50V,GP,TP,5x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,PEF;18nF,5%,50V,TP,6.5x12.5x3.5mm C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;33uF,20%,16V,GP,TP,5x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-FILM,PEF;3.3nF,5%,50V,TP,8.1x4.5x13mm, C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3. C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP C-FILM,PEF;22nF,5%,100V,TP,7.2x4.5x9.0mm C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-AL;1uF,10%,50V,HR,TP,5x11mm,5mm C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1000uF,20%,35V,GP,TP,16x25,7.5 C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5, C-AL;100uF,20%,50V,WT,TP,10x12.5mm,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;470nF,20%,50V,GP,TP,5x11,5 C-AL;1uF,10%,50V,HR,TP,5x11mm,5mm C-FILM,MPEF;68nF,5%,100V,TP,-,5mm C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5 C-FILM,MPEF;100nF,5%,250V,TP,16.5x10.3x5 C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-AL;470uF,20%,50V,GP,TP,13x20,5 C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5 C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-AL;22UF,20%,250V,GP,TP,13X20mm,5mm C-AL;2.2uF,20%,250V,LZ,TP,8X11,5 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x C-CERAMIC,MLC-AXIAL;560pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;390pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;680pF,10%,50V,Y5P,TP C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,1 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-AL;1uF,20%,50V,GP,TP,5x11,5

C604 C611 C612 C701 C705 C801 C802 C803 C805 C806 C807 C808 C810 C811 C812 C816 C817 C820 C821 C822 C823 C851 C852 C901 C902 C903 C904 C905 C907 C908 C909 C910 C911 C912 C915 CMPF CMPF CMPW CN501 CN604 CN704 CR401S CR402S CR403S CS601 CS602 CS603 CS608 CS609 CU02 CY801S D101 D102 D103 D201 D202 D203 D204 D205 D206 D207 D208 D210 D299 D301 D302 D401 D402 D403 D404 D405 D407 D601

2401-000603 2202-000279 2202-000279 2305-000665 2202-000183 2401-003025 2201-000119 2301-001342 2201-000991 2401-000262 2201-000599 2301-000016 2305-000412 2401-000302 2401-001840 2401-000480 2401-001840 2401-000703 2401-001486 2301-000192 2201-000370 2401-001192 2301-000235 2401-002144 2202-000796 2401-000480 2202-000796 2401-001333 2401-000027 2201-000193 2201-000573 2301-000445 2401-000480 2305-000470 2202-000127 AA65-30009A AA65-30109A AA65-30104C AA39-20109A 3711-000963 3711-003641 2306-000255 2201-000639 2306-000193 2401-000603 2301-000383 2202-000796 2202-000222 2202-000222 2305-000665 2201-000446 0403-000700 0403-000508 0402-000132 0403-000663 0401-000005 0401-000005 0401-000005 0403-000355 0401-000005 0401-000005 0402-000132 0403-000563 0403-000654 0402-001105 0403-000654 0402-000132 0402-000132 0402-001105 0402-001105 0402-001105 0402-001105 0401-000005

C-AL;1uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3. C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3. C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP C-AL;330uF,20%,400V,GP,ST,30x40,10 C-CERAMIC,DISC;100nF,+80-20%,50V,Y5V,TP, C-FILM,PPF;1.5nF,5%,800V,TP,15x6.5x11.5m C-CERAMIC,DISC;0.56nF,10%,2kV,Y5P,TP,7.5 C-AL;100uF,20%,160V,HR,TP,16x25,7.5 C-CERAMIC,DISC;0.56nF,10%,500V,Y5P,TP,5. C-FILM,PEF;22nF,5%,100V,TP,7.2x4.5x9.0mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;2200uF,20%,25V,GP,-,12.5x25mm, C-AL;47uF,20%,160V,HR,TP,13x20mm,5m C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-CERAMIC,DISC;0.22nF,10%,50V,Y5P,TP,4x3 C-AL;33uF,20%,50V,GP,TP,6.3x11,5 C-FILM,PEF;3.9nF,5%,50V,TP,6.5x3.0x5.5mm C-AL;47uF,20%,16V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-AL;470nF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,DISC;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,DISC;0.047nF,5%,50V,NP0,TP,5x3 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;10uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;68nF,5%,100V,TP,-,5mm C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V CLAMP-FBT;ABS,V0,BLK,-,-,CLAMP-FBT;NYLON-66,V2,BLK,-,-,CLAMP-WIRE;NYLON 66,V2,NTR,W1 Z4,ALL MOD LEAD CONNECTOR-ASSY;-,YBNH025-08,S,8P,40 CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGH CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIG C-FILM,MPPF;7.4nF,3%,1.6KV,TP,28.5x18.5x C-CERAMIC,DISC;0.68nF,10%,2kV,Y5P,TP,9x5 C-FILM,MPPF;360nF,5%,200V,TP,21x18.5x13, C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-CERAMIC,DISC;3.3nF,20%,400V,Y5U,TP,15x DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,T DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-ZENER;MTZ3.3B,3.3V,3.32-3.53V,500m DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500 DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-, DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-, DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-, DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-, DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-, DIODE-SWITCHING;1N4148,100V,200MA,DO-35,

6-2

Samsung Electronics

Electrical Parts List

Loc. No.

Code No.

Description ; Specification

Remark

Loc. No.

Code No.

Description ; Specification

Remark

D701 D801S D802 D802S D803 D803S D804 D804S D805 D806 D814A D855 D856 D901 D902 D903 D904 D905 D906 D907 DS602 DS603 DZ201 DZ202 DZ203 DZ204 DZ205 DZ206 DZ207 DZ208 DZ209 DZ601 DZ602 DZ603 DZ610 DZ802 DZ806 DZ808 DZ901 DZ902 DZ903 DZ904 F801A F801B FA801S FP801S GT101A IC201S IC301 IC601 IC801S IC802 IC901 IC902 JA701 L102 L152 L201 L202 L203 L204 L205 L206 L208 L301 L402 L501 L502 L503 L602 L802 L803 L804 L805 L810 L811 L901

0403-000654 0402-000213 0402-000540 0402-000213 0402-001105 0402-000213 0403-000654 0402-000213 0402-000213 0401-000005 0402-001351 0403-000508 0403-000508 0401-000005 0403-000508 0401-000005 0401-000005 0403-000508 0403-000508 0401-000005 0403-000656 0403-000656 0403-000654 0403-000654 0403-000654 0403-000654 0403-000654 0403-000654 0403-000654 0403-000654 0403-000654 0403-000562 0403-000656 0403-000656 0403-000563 0403-000658 0403-000294 0403-000699 0403-000508 0403-000508 0403-000355 0403-000508 3602-000114 3602-000114 3601-001086 3601-001012 AA39-20010D 1204-001259 1204-000475 1201-001308 1203-001932 1203-001532 AA13-00081A 1103-001107 3722-001453 2701-000178 2701-000202 AA26-10004K 2701-000207 2701-000158 2701-000207 AA26-10004C 2701-000111 2701-000114 2701-000116 2701-001032 2701-000184 2701-000184 2701-000184 2701-000158 3301-001223 2901-000297 3301-001223 2901-000297 2701-001032 2901-000297 2701-000197

DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-, DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41 DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-RECTIFIER;YG911S2R,200V,5A,TO-220, DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-SWITCHING;1N4148,100V,200MA,DO-35, DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m DIODE-ZENER;MTZ7.5B,7.5V,7.07-7.45V,500m DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m DIODE-ZENER;MTZ18A,18V,16.22-17.06V,500m DIODE-ZENER;MTZ4.7B,4.7V,4.55-4.80V,500m DIODE-ZENER;TZP27B,27V,27-30.8V,1W,DO-41 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 FUSE-HOLDER;-,-,30mohm FUSE-HOLDER;-,-,30mohm FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS FUSE;250V,4A,SLOW-BLOW,GLASS,5.2x20 LEAD CONNECTOR-ASSY;-,YFH800-01,S,1P,400 IC-VIDEO SYSTEM;TA1282N,DIP,56P,600MIL,P IC-VIDEO SYSTEM;KA2131,SIP,10P,-,PLASTIC IC-POWER AMP;7266,ZIP,15P,-,DUAL,26dB,PL IC-PWM CONTROLLER;5Q0765,TO-220F,5P,185M IC-POSI.FIXED REG.;7631,SIP,10P,-,PLASTI IC-MCU;Z9036512PSC-R4474,SZM-370TH,ST IC-EEPROM;24C021C,256x8Bit,DIP,8P,300MIL JACK-RCA;3P,3.4mm,NI,BLK,INDUCTOR-AXIAL;33uH,10%,3x7mm INDUCTOR-AXIAL;560nH,10%,2.5x3.4mm TRANS-IF;-,7MG,SIF,11.5uH,7mm,100pF,4.8 INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm TRANS-IF;-,7MG,VIF,0.37uH,7mm,27pF,52.3 INDUCTOR-AXIAL;100uH,10%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm INDUCTOR-AXIAL;100uH,10%,5x14mm INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP, FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP, FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;100uH,10%,5x14mm FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm

H/SINK

H/SINK H/SINK H/SINK

L902 L999 LC801S LD901 LR401S LX801S NT801S P801S PC801S Q151 Q201 Q202 Q203 Q401 Q402 Q501 Q502 Q503 Q601 Q801 Q903 QU01 R101 R102 R104 R105 R106 R107 R152 R153 R154 R155 R156 R157 R158 R159 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R213 R214 R215 R218 R219 R222 R223 R226 R227 R228 R229 R230 R231 R233 R234 R235 R236 R237 R239 R240 R241 R242 R251 R252 R253 R257 R301 R302 R303

2701-000114 2701-000115 AA27-20003X AA96-30007A AA27-30001B AA29-30001D 1404-001045 1404-001048 0604-001038 0501-000436 0501-002183 0501-002183 0501-002183 0502-001115 0501-000369 0501-002014 0501-002014 0501-002014 0501-002183 1203-001217 0501-002183 0504-000123 2001-001155 2001-001000 2003-000592 2003-000592 2003-000664 2003-000664 2001-000221 2001-000734 2001-000780 2001-000281 2001-000793 2001-000568 2001-000007 2001-000007 2001-000429 2001-000734 2001-000734 2001-000221 2001-000221 2001-000221 2001-001111 2001-000515 2001-000515 2001-000515 2001-000281 2001-000281 2001-000837 2001-000331 2001-000331 2001-000591 2001-000674 2001-000773 2001-000780 2001-000508 2001-000508 2001-000258 2001-000258 2001-000591 2001-000660 2001-000011 2001-000405 2004-000195 2001-000548 2001-000290 2001-000947 2001-000577 2001-000429 2001-000221 2001-000591 2001-000591 2001-000591 2008-000252 2001-000429 2001-000003 2001-000908

INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,3x7mm COIL-DEGAUSSING;-,20,14.4ohm,48T,L2170, ASSY-LED,GUIDE;-,AA61-50055A,DL-G7GA,GRE COIL-LINEARLITY;-,195uH,QIC1010,PI0.4,4. FILTER-LINE NOISE;SQ1913,-,6.0MH,0.8A,THERMISTOR-NTC;4.7OHM,15%,2900K,35.0MW,T THERMISTOR-PTC;7ohm,30%,200/220V,270Vac, PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST TR-SMALL SIGNAL;KTC3197,NPN,625mW,TO-92, TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92, TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92, TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92, TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L, TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L, TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L, TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L, TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92, IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92, TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,T R-CARBON(S);5.6KOHM,5%,1/2W,AA,TP,2.4X6. R-CARBON;82KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m R-METAL OXIDE(S);33ohm,5%,2W,AF,TP,4x12m R-METAL OXIDE(S);33ohm,5%,2W,AF,TP,4x12m R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;27OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON(S);240OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;51KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;470KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;180OHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m R-CARBON;270KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-FUSIBLE(S);0.47ohm,10%,1/2W,AF,TP,2.5x R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;62KOHM,5%,1/8W,AA,TP,1.8X3.2MM

Samsung Electronics

6-3

Electrical Parts List

Loc. No.

Code No.

Description ; Specification

Remark

Loc. No.

Code No.

Description ; Specification

Remark

R304 R305 R306 R307 R308 R309 R401 R402 R403 R404 R405 R406 R407 R409 R410 R411 R412 R415 R416 R417 R444 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R517 R518 R599 R601 R602 R603 R604 R606 R607 R610 R611 R701 R702 R801 R802 R803 R807 R808 R809 R810A R811 R812 R814 R816 R817 R819 R819A R820 R821 R823 R824 R825 R852 R853 R854 R901 R902 R903 R904 R905 R906

2003-000436 2001-000947 2001-000766 2001-000864 2001-000908 2003-001043 2001-000780 2001-000515 2001-001114 2001-001136 2003-000540 2008-001107 2003-002102 2008-000253 2008-000206 2004-001373 2004-001373 2003-000784 2001-000022 2001-001410 2001-001099 2001-000007 2001-000007 2001-000007 2003-002170 2003-002170 2003-002170 2001-000281 2001-000281 2001-000281 2001-000628 2001-000628 2001-000628 2001-000666 2001-000666 2002-001006 2001-000666 2008-001015 2008-001053 2001-000429 2001-000290 2004-000195 2001-000947 2001-000258 2001-000290 2001-000793 2001-000429 2001-001187 2004-001373 2001-001150 2003-000994 2003-000994 2003-000994 2001-001150 2008-000205 2008-000261 2001-001170 2008-000252 2001-000864 2001-001192 2001-001170 2008-000284 2008-000284 2001-000019 2004-004089 2001-000109 2004-001983 2001-001108 2004-001371 2004-001390 2001-001125 2001-000793 2001-000429 2001-000281 2001-000281 2001-000429 2001-000472

R-METAL OXIDE(S);1.5ohm,5%,1W,AF,TP,3.3x R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;43KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;62KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL OXIDE(S);510ohm,5%,1W,AF,TP,2.5x R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);36OHM,5%,1/2W,AA,TP,2.4X6.4M R-METAL OXIDE(S);1Kohm,5%,2W,AF,TP,4x12m R-FUSIBLE(S);300ohm,5%,2W,AG,TP,3.9x12mm R-METAL OXIDE;68Kohm,5%,2W,AF,TP,4x12mm R-FUSIBLE(S);0.47ohm,5%,1W,AF,TP,3.9x10m R-FUSIBLE(S);1ohm,5%,1/2W,AF,TP,2.5x6.5m R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4 R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4 R-METAL OXIDE(S);7.5Kohm,5%,2W,AF,TP,4x1 R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4M R-CARBON(S);43OHM,5%,1/2W,AA,TP,2.4X6.4M R-CARBON(S);2.7KOHM,5%,1/2W,AA,TP,2.4X6. R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm R-FUSIBLE;22ohm,5%,1/2W,AF,TP,2.5x6.5mm R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON(S);75OHM,5%,1/2W,AA,TP,2.4X6.4M R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4 R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6. R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6. R-FUSIBLE(S);10ohm,5%,1/2W,AF,TP,2.5x6.5 R-FUSIBLE(S);150ohm,5%,1W,AF,TP,3.9x10mm R-CARBON(S);6.8OHM,5%,1/2W,AA,TP,2.4X6.4 R-FUSIBLE(S);0.47ohm,10%,1/2W,AF,TP,2.5x R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON(S);820OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);6.8OHM,5%,1/2W,AA,TP,2.4X6.4 R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4M R-METAL(S);123Kohm,1%,1/2W,AA,TP,2.5x6.5 R-CARBON(S);470OHM,5%,1/2W,AA,TP,2.4X6.4 R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6. R-CARBON(S);22KOHM,5%,1/2W,AA,TP,2.4X6.4 R-METAL(S);1.5Kohm,1%,1/2W,AA,TP,2.4x6.4 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2.4X6. R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

R907 R909 R910 R911 R913 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R929 R930 R931 R932 R933 R936 R937 R938 R939 R940 R941 R951 R952 R988 RH01 RH02 RM901 RR401S RS601 RS602 RS604 RS605 RS606 RS607 RS613 RS614 RU02 RU06 RU07 RU10 RY801S SF101S SW901 SW902 SW903 SW904 SW905 SW906 T401 T444S T801S TU01S V999S VX801S X201 X202 X901 Z201 Z601

2001-000995 2001-000613 2001-000995 2001-000290 2001-000924 2001-000577 2001-000734 2001-000947 2001-000947 2001-000947 2001-000977 2001-000522 2001-000290 2001-000281 2001-000281 2001-000449 2001-000449 2001-000008 2001-000290 2001-000232 2001-000290 2001-000429 2001-000290 2001-000290 2004-000195 2001-000290 2001-000429 2001-000449 2001-000708 2001-000281 2001-000734 2001-000472 2001-000508 2002-001006 2002-001006 AA59-60001U 2004-001390 2001-000734 2001-000734 2001-000258 2001-000290 2001-000429 2001-000085 2001-000273 2001-000281 2001-000780 2001-000397 2001-001062 2001-000924 2002-001013 2904-000304 3404-000244 3404-000244 3404-000244 3404-000244 3404-000244 3404-000295 AA26-50001B AA26-30001Y AA26-00043A AA40-10006U 3704-001105 1405-000152 2801-003725 2802-000172 2801-003224 2903-001022 2903-000135

R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;8.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;39OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2M R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x MODULE-REMOCON;-,ORC-50VF/SR-12V,38KHz,9 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON(S);100KOHM,5%,1/2W,AA,TP,2.4X6. R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MM R-COMPOSITION;4.7Mohm,5%,1/2W,AA,TP,3.7x FILTER-SAW AV;45.75MHz,SIP5K,ST,14.7dB,M SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP SWITCH-TACT;12VDC,50mA,160gf,8.4X22.7,SP TRANS-HORIZ.DRIVE;-,7.1mH,102uH,10-20uH, TRANS-FLYBACK;-,FSV-20A001,20,125V TRANS SWITCHING;-,-,-,AC90~260V,125/12.5 TUNER-F/S;TECC1070PG31A(S),NTSC,TR,181CH SOCKET-CRT;11P,20PI,26.5PI,NI,VARISTOR;560V,2500A,14x8.5mm,TP CRYSTAL-UNIT;3.579545MHz,20ppm,28-AAM,16 RESONATOR-CERAMIC;503.5KHZ,0.5%,BK,7.0X3 CRYSTAL-UNIT;32.768KHZ,20PPM,28-AAY,12.5 FILTER-CERAMIC;BR,4.5MHz,-,-,-,TP,FILTER-CERAMIC;BP,4.5MHz,120KHz,6dB,-,TP

ASSY CABINET FRONT
* AA91-00283B ASSY CABINET FRONT;-,20S4,(SPK)SV704 EPG * AA90-00244B ASSY CABINET;20S4,CT2088BL6X/XAP ASPK AA96-00287A ASSY SPEAKER;-,8ohm,15W,001115/001088,AA

6-4

Samsung Electronics

Electrical Parts List

Loc. No.

Code No.

Description ; Specification

Remark

Loc. No.

Code No.

Description ; Specification

Remark

BACK BADGE C/B CB+CF CMPC CMPD CMPW CRT+CF CVRC CVRT FRONT GRILLEW GRILLEW INLAY KC+CF KNOBC KNOBP LEAD LED PA+CF POWER SPA SPA SPK SPK SPK+CF STOPP WRMC

AA64-00701C AA64-70123B AA63-60001X 6003-001026 AA65-30008A AA65-30107A AA65-30105A AA60-10050R AA63-00202C AA63-00226B AA64-00700D AA63-00204B AA63-00205B AA64-60385G 6003-001026 AA64-00702B AA64-00703D AA39-00091A AA64-00705B 6003-001024 AA61-60003J AA63-60002W AA63-60001P 3001-001088 3001-001115 6003-001026 AA61-40113A AA64-00704B

CABINET BACK;-,20S4,-,HIPS,HB,BLK,-,BADGE-BRAND;AL,R2000,SILVER,L=50,SAMSUNG SPACER-FELT;FELT,T0.5,BLK,330X15,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR CLAMP-CORD;PE,HB,BLK,-,-,CLAMP-D,COIL;NYLON 66,V2,NTR,-,20~22 INC CLAMP-WIRE;NYLON 66,V2,NTR,15MM,ALL MODE SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC COVER-CONTROL;-,20S4,GD906P EPG NT,HIPS, COVER-TOP,LATIN;-,20S4,T/SOUND,ABS,LG TR CABINET FRONT;-,20S4,SV704P PGB2000,HIPS GRILLE-WOOFER,L;-,20S4,-,SECC,T0.5,SV704 GRILLE-WOOFER,R;-,20S4,-,SECC,T0.5,SV704 INLAY BACK;3E,K15A-1 3PIN S/T,PS SHEET,T SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR KNOB CONTROL;-,20S4,-,ABS,HB,G3676 KNOB POWER;-,20S4,T/S NO-SILK,ABS,HB,G36 LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,52 INDICATOR LED;-,20S4,-,ACRYL,-,CLR,SCREW-TAPTITE;RWH,+,B,M4,L12,ZPC(YEL),SW SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,SPACER-FELT;FELT,T0.5,BLK,30X10,-,SPACER-FELT;FELT,T1.0,BLK,230X15,-,SPEAKER;5W,8ohm,90dB,250Hz+-50Hz SPEAKER;15W,8ohm,93dB,110 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR STOPPER-PCB;501H,HIPS,NTR,HB,-,WINDOW REMOCON;-,20S4,-,PC,V0,VIOLET,-

ICA02 PCBS QA01 RA01 RA05 RA06 RA07 RA08 RA18 RA19

1204-001455 AA41-00072A 0501-000389 2001-000449 2001-000577 2001-000577 2001-000281 2001-000281 2001-000674 2001-000281

IC-VOLUME/TONE CONT.;TDA7449,DIP,20P,300 PCB-STEREO MODULE;K15A,1L,FR-1,245X245X1 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM

ASSY-PCB,A/V FRONT
* AA95-00577AASSY-PCB,A/V FRONT;-,CT2088BL6,K15A,-,-, CE01 CE02 CN705A JE601 JR01 PCBAV RE01 RE02 2401-000480 2401-000480 AA39-20071D 3722-000143 3722-001031 AA41-00227A 2001-001077 2001-001077 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 LEAD CONNECTOR-ASSY;-,YBNH025-12,67096-0 JACK-PHONE;1P(VER),3.4mm,AG,BLK,NO JACK-RCA;3P,3.6MM,#18,AU PCB-AV FRONT;K15A-1,1L,FR-1,245x245x1.6T R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4

ASSY-POWER,CORD
* AA96-20109C ASSY-POWER,CORD;-,CP2/NO(4.0),H/C300,KKP HDRP PCORD AA61-20284A HOLDER;-,P-CORD,PP,VO,BLK,KE-002 AA39-10006X POWER-CORD;-,KKP419C,KLCE-2F,2.286MT,3P,

ASSY ACCESSORY
* AA94-02098AASSY ACCESSORY;CT2088BL6X/XAP,K15A,PANAM ANT BATT IB IB IB PLUG TRANS AA42-10001V 4301-000120 AA68-00790A AA68-00791A AA68-30004A 3721-000136 AA26-90001F ANT-ROD;-,3S,620mm,BRN,UL/CSA BATTERY-MN;1.5V,-,AA,14.5x50mm,MANUAL USERS;K15A,W/P100(G),32PAGE,A5,1' MANUAL USERS;K15A,W/P100(G),32PAGE,A5,1' MANUAL-BOOK;-,W/P120(G),-,SEPA,-,PLUG-CONVERSION;2P,4.0mm,N,NI TRANS-MATCHING;-,300ohm/75ohm,NTSC,40-89

REMOCON
* AA59-00077AREMOCON;-,TM59,SZM370PH,25,L/GRAY,SS,E

ASSY-CRT
* AA94-50019L ASSY-CRT;A48KRD82X(HB),+380MG,20,BARE, CRT DY MGNT SPA AA03-10029Z AA27-50004W AA27-00002A AA63-60028A CRT-COLOR;-,A48KRD82X(HB),+380mG,20,90d DEFLECTION-YOKE;-,DSE-1992LL(1H),20'/A48 MAGNET-CONVERGENCE;-,JH291-SC-OB,29.1MM SPACER-DY;NEOPRENE,-,BLK,V0 W12,-,-

ASSY-PCB,SOUND
* AA95-00437AASSY-PCB,SOUND;-,CT5066BZG,K15A,-,-,TURB CA01 CA02 CA03 CA04 CA05 CA06 CA07 CA08 CA09 CA10 CA11 CA12 CA13 CA32 CNA01 CNA02 CNA03 DA01 2401-000480 2401-000603 2401-000603 2401-000603 2401-000603 2305-000708 2305-000355 2305-000355 2305-000708 2301-000289 2301-000289 2401-000027 2401-000027 2202-000121 3711-002702 3711-002703 AA61-10068A 0403-000654 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;150nF,5%,100V,TP,16.5x10.3x5 C-FILM,MPEF;330nF,5%,63V,TP,-,5mm C-FILM,MPEF;330nF,5%,63V,TP,-,5mm C-FILM,MPEF;150nF,5%,100V,TP,16.5x10.3x5 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP CONNECTOR-HEADER;NOWALL,4P,1R,2.5mm,ANGL CONNECTOR-HEADER;NOWALL,5P,1R,2.5mm,ANGL BRACKET-PCB;-,M2160,SPTE,T0.3,-,-,DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m

Samsung Electronics

6-5

MEMO

6-6

Samsung Electronics

Block Diagram

7. Block Diagram

IC601 TU01 SF101 SAW M1859M SOUND AMP SOUND MODULE PCB TURBO SOUND TDA7266S 2- CH

SPEAKER 8ohm 6W

TELH9-212A (TECC107OPG31A)

TUNER

IC902 EEPROM KS24C020 IC901 IC201S

SOUND EXT IN VIDEO R,G,B VIDEO EXT IN AUDIO

CRT

1 - CHIP
MICOM SZM370TH
I C BUS
2

1F/V/C/D KA2163B(TA1282N)
IC301

VERTICAL-AMP IC
D801~D804 125V SWITCHING TRANS POWER-CORD CP2-NO(4.0) S:125V,12.5V 12.5V Q401

KA2131
HORIZONTAL-TR

KSC5386
T444S IC802

IC801S

T801S
PC802

MULTI-REGULATOR

5V MICOM 9V 1-CHIP

SAPS CONTROL IC

KA3SO680

PHOTO COULPER

KA7631

FBT
FSV20A001(S)

Samsung Electronics

7-1

MEMO

7-2

Samsung Electronics

Wiring Diagram

8. Wiring Diagram

S P E A K E R

L+ LL+ L-

CN604

SOUND MODULE PCB

R- OUT L- OUT GND A/V R IN A/V L IN TV-SOUND 9V SCL SDA2 D.Y

R- OUT L- OUT GND A/V R IN A/V L IN TV-SOUND 9V SCL SDA2

C R T

H1 H2 V1 V2

H1 H2 V1 V2

M A I N A S S Y

R G B 9V GND 180V GND HEATER CN201 CN703 R-IN R-OUT V-OUT L - IN L- OUT V - IN GND AV-L OUT AV-L IN

R G B 9V GND 180V GND HEATER CN501

C R T P C B

R-IN R-OUT V-OUT L - IN L- OUT V - IN GND AV-L OUT AV-L IN

A/V ASSY

Samsung Electronics

8-1

MEMO

8-2

Samsung Electronics

Schematic Diagrams

9. Schematic Diagrams
9-1 MAIN 1/4
TP7 TP1

TP8

TP2

TP10 TP11

TP9

TP3

TP9

TP2
TP10 TP4

TP1

TP4 TP3 TP5

TP8
TP11 TP5

TP7
TP6

TP6

: Power Line : Signal Line Samsung Electronics 9-1

Schematic Diagrams

9-2 MAIN 2/4
TP18 TP12

TP19

TP13

TP12

TP20

TP14

TP15 TP13 TP14 TP17
TP21 TP15

TP16 TP18

TP19

TP20

TP21 TP23

TP22

TP16

TP22
TP23 TP17

: Power Line : Signal Line

9-2

Samsung Electronics

Schematic Diagrams

9-3 MAIN 3/4
TP38
TP30 TP24

TP31

TP25

TP36 TP37

TP32

TP26

TP33

TP27

TP32 TP25 TP27 TP33 TP24 TP26 TP30 TP31 TP35
TP34 TP28

TP34

TP28

TP35

TP29

TP29

TP36

TP37

TP38

: Power Line

Samsung Electronics

9-3

Schematic Diagrams

9-4 MAIN 4/4

: Power Line : Signal Line

9-4

Samsung Electronics