Text preview for : SONY GV-D1000, D1000E SERVICE MANUAL LEVEL 2 VER 1.2 2003.06 (9-929-929-33).pdf part of SONY GV-D1000 SONY GV-D1000, D1000E.
DIGITAL VIDEO CASSETTE RECORDER.
SERVICE MANUAL VERSION 1.2 2003.06
PART#(9-929-929-33)
Back to : SONY GV-D1000, D1000E SER | Home
GV-D1000/D1000E
RMT-811
SERVICE MANUAL
Ver 1.2 2003. 06
Revision History
LEVEL
2
US Model Canadian Model
GV-D1000
AEP Model UK Model E Model
GV-D1000E
Photo : GV-D1000E
J200 MECHANISM
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS ADJUSTMENTS REPAIR PARTS LIST
· For INSTRUCTION MANUAL, refer to separate file (992992972.pdf). · For MECHANISM ADJUSTMENTS, refer to the "DV MECHANICAL ADJUSTMENT MANUAL J MECHANISM " (9-929-807-11). On the MS-95 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the MS-95 board. Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the MS-95 board are not shown. The following pages are not shown. Schematic diagram ............................. Pages 4-43 to 4-52 Mounted parts location ............................. Page 4-80 Printed wiring board ............................ Pages 4-71 to 4-72 Electrical parts list ................................... Pages 6-10 to 6-11 Waveforms ........................................... Page 4-76
DIGITAL VIDEO CASSETTE RECORDER
GV-D1000/D1000E
COVER
SPECIFICATIONS
VCR
System
Video recording system 2 rotary heads Helical scanning system Audio recording system Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs 48 kHz, stereo) Video signal PAL colour, CCIR standards Usable cassette Mini DV cassette with the mark printed Tape speed SP: Approx. 18.81 mm/s LP: Approx. 12.56 mm/s Recording/playback time (using cassette DVM60) SP: 1 hour LP: 1.5 hours Fastforward/rewind time (using cassette DVM60) Approx. 2 min.
Input/output connectors
S video input 4-pin mini DIN Luminance signal: 1 Vp-p, 75 (ohms), unbalanced GV-D1000 : Chrominance signal: 0.286 Vp-p 75 (ohms), unbalanced GV-D1000E : Chrominance signal: 0.3 Vp-p, 75 (ohms), unbalanced
S video output 4-pin mini DIN Luminance signal: 1 Vp-p, 75 (ohms), unbalanced GV-D1000 : Chrominance signal: 0.286 Vp-p 75 (ohms), unbalanced GV-D1000E : Chrominance signal: 0.3 Vp-p, 75 (ohms), unbalanced Audio/Video input AV MINIJACK Video: 1 Vp-p, 75 (ohms), unbalanced, sync negative Audio: 327 mV, input impedance more than 47 k (kilohms) Video output Phono jack, 1 Vp-p, 75 (ohms), unbalanced, sync negative Audio output Phono jacks (2) 327 mV, output impedance less than 1 k (kilohms) DV jack 4-pin connector: S100 Headphone jack Stereo minijack (ø 3.5 mm) LANC jack Stereo minijack (ø 2.5 mm) USB jack Mini-B
LCD screen
AC power adaptor
Power requirements 100 - 240 V AC, 50/60 Hz Output voltage DC OUT: 8.4 V, 1.5 A in the operating mode Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F) Dimensions (approx.) 125 × 39 × 62 mm (5 × 1 9/16 × 2 1/2 in.) (w/h/d) excluding projecting parts Mass (approx.) 280 g (9.8 oz) excluding power cord Design and specifications are subject to change without notice.
Picture 10 cm (4.0 type) 80.6 × 60.5 mm (3 1/4 × 2 1/2 in.) Total dot number 123 200 (560 × 220)
General
Power requirements 8.4 V (AC power adaptor) 7.2 V (battery pack) Average power consumption During playback using LCD 5.2 W During playback when you close the LCD panel 3.5 W Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F) Dimensions (Approx.) 148 × 65 × 133 mm (5 7/8 × 2 5/8 × 5 1/8 in.) (w/h/d) Mass (approx.) 880 g (1 lb 15 oz) excluding the battery pack and cassette Supplied accessories See page 3.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
--2--
GV-D1000/D1000E
· SUPPLIED ACCESSORIES
Make sure that the following accessories are supplied with your camcorder.
1 2 3
4
5
6
7
8
9
1 AC-L10A/L10B/L10C AC power adaptor (1), power cord (mains lead) (1) 2 A/V converting cable (1) 3 A/V connecting cable (1) 4 USB cable (1) 5 Wireless Remote Commander (1)
6 Size R6 (AA) battery for Remote Commander (2) 7 CD-ROM (SPVD-008 (I) USB Driver) (1) (GV-D1000) CD-ROM (SPVD-008 USB Driver) (1) (GV-D1000E) 8 21-pin adaptor (1) (GV-D1000E : AEP, UK only) 9 2-pin conversion adaptor (GV-D1000E : E only)
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
GV-D1000/D1000E
TABLE OF CONTENTS 1. SERVICE NOTE
1-1. SERVICE NOTE ····························································· 1-1 1. POWER SUPPLY DURING REPAIRS ·························· 1-1 2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ····························································· 1-1 1-2. SELF-DIAGNOSIS FUNCTION ···································· 1-2 1. SELF-DIAGNOSIS FUNCTION ···································· 1-2 2. SELF-DIAGNOSIS DISPLAY ······································· 1-2 3. SERVICE MODE DISPLAY ·········································· 1-2 3-1. Display Method ······························································· 1-2 3-2. Switching of Backup No. ················································ 1-2 3-3. End of Display ································································· 1-2 4. SELF-DIAGNOSIS CODE TABLE ································ 1-3 · VC-275 (DV INTERFACE)(3/13) SCHEMATIC DIAGRAM ···························· 4-21 · VC-275 (VIDEO IN/OUT)(4/13) SCHEMATIC DIAGRAM ···························· 4-23 · VC-275 (USB SIGNAL PROCESS)(5/13) SCHEMATIC DIAGRAM ···························· 4-25 · VC-275 (MECHANISM CONTROL)(6/13) SCHEMATIC DIAGRAM ···························· 4-27 · VC-275 (DRUM/CAPSTAN MOTOR DRIVE)(7/13) SCHEMATIC DIAGRAM ···························· 4-29 · VC-275 ((HI CONTROL)(8/13) SCHEMATIC DIAGRAM ···························· 4-31 · VC-275 (AUDIO)(9/13) SCHEMATIC DIAGRAM ···························· 4-33 · VC-275 (VIDEO, AUDIO, USB JACK)(10/13) SCHEMATIC DIAGRAM ···························· 4-35 · VC-275 (DC IN, CHARGE)(11/13) SCHEMATIC DIAGRAM ···························· 4-37 · VC-275 (DC/DC CONVERTER)(12/13) SCHEMATIC DIAGRAM ···························· 4-39 · VC-275 (CONNECTOR)(13/13) SCHEMATIC DIAGRAM ···························· 4-41 Shematic diagram of the MS-95 board are not shown. Pages from 4-43 to 4-52 are not shown. 4-3. PRINTED WIRING BOARDS ····································· 4-53 · FK-81 (SWITCH BLOCK) PRINTED WIRING BOARD ······················· 4-53 · PD-130 (LCD DRIVER, BACK LIGHT) PRINTED WIRING BOARD ······················· 4-55 · LS-56 (LCD SWITCH), PRINTED WIRING BOARD ······················· 4-58 · EX-39 (MULTI CONNECTOR) PRINTED WIRING BOARD ······················· 4-59 · IO-69 (AV IN/OUT) PRINTED WIRING BOARD ······················· 4-61 · PR-41 (REMOTE COMMANDER RECEIVER), FP-575 (LANC) PRINTED WIRING BOARDS ····················· 4-63 · FP-100 (MODE SWITCH), FP-228 (DEW SENSOR), FP-102 (TAPE TOP/END SENSOR, S/T REEL), FP-571 (BATTERY) FLEXIBLE BOARDS ··································· 4-65 · EJ-35 (EJECT SWITCH) PRINTED WIRING BOARD ······················· 4-65 · VC-275 (REC/PB AMP, DV SIGNAL PROCESS, DV INTERFACE, VIDEO IN/OUT, USB SIGNAL PROCESS, MECHANISM CONTROL, DRUM/ CAPSTAN MOTOR DRIVE, HI CONTROL, AUDIO, VIDEO, USB JACK, DC IN, CHARGE, DC/DC CONVERTER, CONNECTOR) PRINTED WIRING BOARD ······················· 4-67 Printed wiring board of the MS-95 board are not shown. Pages from 4-71 to 4-72 are not shown. 4-4. WAVEFORMS ······························································ 4-73 Waveforms of the MS-95 board are not shown. Page 4-76 is not shown. 4-5. MOUNTED PARTS LOCATION ································· 4-77 Mounted parts location of the MS-95 board is not shown. Page 4-80 is not shown.
2.
DISASSEMBLY
2-1. LCD CABINET ASSEMBLY ········································· 2-2 2-2. PD-130 BOARD, LS-56 BOARD ··································· 2-3 2-3. LCD WINDOW CABINET ASSEMBLY (LCD901, ND901, SP901, SP902) ·································· 2-4 2-4. BOTTOM CABINET ASSEMBLY, FP-571 FLEXIBLE BOARD (V/L RECHARGEABLE BATTERY) ············· 2-5 2-5. VC-275 BOARD ····························································· 2-5 2-6. BATTERY TERMINAL BOARD ··································· 2-6 2-7. FP-575 FLEXIBLE BOARD (LANC), PR-41 BOARD, IO-69 BOARD ································································· 2-6 2-8. MS-95 BOARD ······························································· 2-7 2-9. MECHANISM DECK ····················································· 2-7 2-10. EJ-35 BOARD ································································· 2-8 2-11. EX-39 BOARD ······························································· 2-9 2-12. MEMORY STICK CONNECTOR (10P), FK-81 BOARD ······························································ 2-10 2-13. FP-602 FLEXIBLE BOARD (DV IN/OUT), LCD BLOCK ASSEMBLY ··········································· 2-11 2-14. HINGE UNIT, FP-569 FLEXIBLE BOARD ················ 2-12 2-15. CIRCUIT BOARDS LOCATION ································· 2-14 2-16. FLEXIBLE BOARDS LOCATION ······························ 2-15
3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8.
BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/5) ··························· 3-1 OVERALL BLOCK DIAGRAM (2/5) ··························· 3-3 OVERALL BLOCK DIAGRAM (3/5) ··························· 3-5 OVERALL BLOCK DIAGRAM (4/5) ··························· 3-7 OVERALL BLOCK DIAGRAM (5/5) ··························· 3-9 POWER BLOCK DIAGRAM (1/3) ······························ 3-11 POWER BLOCK DIAGRAM (2/3) ······························ 3-13 POWER BLOCK DIAGRAM (3/3) ······························ 3-15
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2) ······················· 4-1 FRAME SCHEMATIC DIAGRAM (2/2) ······················· 4-3 4-2. SCHEMATIC DIAGRAMS ············································ 4-7 · PD-130 (LCD DRIVER)(1/2) SCHEMATIC DIAGRAM ······························ 4-7 · PD-130 (BACK LIGHT)(2/2) SCHEMATIC DIAGRAM ······························ 4-9 · FK-81 (SWITCH BLOCK) SCHEMATIC DIAGRAM ···························· 4-11 · EX-39 (MULTI CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-13 · IO-69 (AV IN/OUT) SCHEMATIC DIAGRAM ···························· 4-15 · VC-275 (REC/PB AMP)(1/13) SCHEMATIC DIAGRAM ···························· 4-17 · VC-275 (DV SIGNAL PROCESS)(2/13) SCHEMATIC DIAGRAM ···························· 4-19
--4--
GV-D1000/D1000E
5.
ADJUSTMENTS
1. Adjusting items when replacing main parts and boards. · 5-2 5-1. ADJUSTMENT PREPARATIONS ································· 5-3 1-1. PREPARATIONS BEFORE ADJUSTMENT ················· 5-3 1-1-1. List of Service Tools ························································ 5-3 5-2. MECHANISM SECTION ADJUSTMENT ···················· 5-4 2-1. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ····································································· 5-4 2-2. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ····································································· 5-4 2-3. TAPE PATH ADJUSTMENT ·········································· 5-4 1. Preparation for Adjustment ············································· 5-4 2. Processing after Completing Operations ························· 5-4 5-3. ELECTRICAL ADJUSTMENT ······································ 5-5 3-1. PREPARATIONS BEFORE ADJUSTMENTS ·············· 5-5 3-1-1. Equipment to Required ···················································· 5-5 3-1-2. Precautions on Adjusting ················································· 5-6 3-1-3. Adjusting Connectors ······················································ 5-6 3-1-4. Connecting the Equipment ·············································· 5-7 3-1-5. Alignment Tapes ······························································ 5-8 3-1-6. Input/Output Level and Impedance ································· 5-8 3-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA · 5-9 3-2-1. INITIALIZATION OF E, F, 7 PAGE DATA ··················· 5-9 1. Initializing the E, F, 7 Page Data ····································· 5-9 2. Modification of E, F, 7 Page Data ··································· 5-9 3. F Page Table ···································································· 5-9 4. E Page Table ···································································· 5-9 5. 7 Page Table ····································································· 5-9 3-2-2. INITIALIZATION OF C, D, 8 PAGE DATA ················ 5-10 1. Initializing the C, D, 8 Page Data ·································· 5-10 2. Modification of C, D, 8 Page Data ································ 5-10 3. C Page Table ·································································· 5-10 4. D Page Table ·································································· 5-12 5. 8 Page Table ··································································· 5-13 3-2-3. INITIALIZATION OF B PAGE DATA ························· 5-14 1. Initializing the B Page Data ··········································· 5-14 2. Modification of B Page Data ········································· 5-14 3. B Page Table ·································································· 5-14 3-3. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-15 1. Serial No. Input ····························································· 5-15 1-1. Company ID Input ························································· 5-15 1-2. Serial No. Input ····························································· 5-15 3-4. SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-17 1. Cap FG Duty Adjustment (VC-275 board) ··················· 5-17 2. PLL f0 & LPF f0 Adjustment (VC-275 board) ·············· 5-17 3. Switching Position Adjustment (VC-275 board) ··········· 5-18 4. AGC Center Level and APC & AEQ Adjustment ········· 5-18 4-1. Preparations before adjustments ···································· 5-18 4-2. AGC Center Level Adjustment (VC-275 board) ··········· 5-19 4-3. APC & AEQ Adjustment (VC-275 board) ···················· 5-19 4-4. Processing after Completing Adjustments ···················· 5-20 5. PLL f0 & LPF f0 Fine Adjustment (VC-275 board) ······ 5-20 3-5. VIDEO SYSTEM ADJUSTMENTS ····························· 5-21 1. 40.5MHz/54MHz Origin Oscillation Adjustment (MS-95 board) ······························································· 5-21 2. Chroma BPF f0 Adjustment (VC-275 board) ················ 5-21 3. S VIDEO OUT Y Level Adjustment (VC-275 board) ··· 5-22 4. S VIDEO OUT Chroma Level Adjustment (VC-275 board) ····························································· 5-22 3-6. AUDIO SYSTEM ADJUSTMENTS ···························· 5-24 1. Playback Level Check ··················································· 5-24 2. Overall Level Characteristics Check ····························· 5-24 3. Overall Distortion Check ··············································· 5-24 4. Overall Noise Level Check ············································ 5-25 5. Overall Separation Check ·············································· 5-25 3-7. LCD SYSTEM ADJUSTMENT ··································· 5-26 1. LCD Initial Data Input (1) ············································· 5-26
2. 3. 4. 5. 6. 7. 8. 5-4. 4-1. 1. 2. 4-2. 4-3. 1. 2. 2-1. 2-2. 3. 4. 5. 6. 7. 8. 9. 10.
LCD Initial Data Input (2) ············································· 5-27 VCO Adjustment (PD-130 board) ································· 5-27 RGB AMP Adjustment (PD-130 board) ························ 5-28 Contrast Adjustment (PD-130 board) ···························· 5-28 COM AMP Adjustment (PD-130 board) ······················· 5-29 V-COM Adjustment (PD-130 board) ···························· 5-29 White Balance Adjustment (PD-130 board) ·················· 5-30 SERVICE MODE ·························································· 5-31 ADJUSTMENT REMOTE COMMANDER ················ 5-31 Using the adjustment remote commander ····················· 5-31 Precautions upon using the adjustment remote commander ···································································· 5-31 DATA PROCESS ··························································· 5-32 SERVICE MODE ·························································· 5-33 Setting the Test Mode ···················································· 5-33 Emergence Memory Address ········································ 5-33 EMG Code (Emergency Code) ····································· 5-33 MSW Code ···································································· 5-34 Bit value discrimination ················································ 5-35 Switch check (1) ···························································· 5-35 Switch check (2) ···························································· 5-35 Switch check (3) ···························································· 5-35 Switch check (4) ···························································· 5-36 Switch check (5) ···························································· 5-36 Record of Use check ······················································ 5-37 Record of Self-diagnosis check ····································· 5-37
6.
REPAIR PARTS LIST
6-1. EXPLODED VIEWS ······················································ 6-1 6-1-1. OVERALL SECTION ····················································· 6-1 6-1-2. CABINET (UPPER) SECTION-1 ·································· 6-2 6-1-3. CABINET (UPPER) SECTION-2 ·································· 6-3 6-1-4. LCD SECTION ······························································· 6-4 6-1-5. CASSETTE COMPARTMENT AND DRUM BLOCK ASSEMBLY ···································································· 6-5 6-1-6. LS CHASSIS BLOCK ASSEMBLY ······························· 6-6 6-1-7. MECHANISM CHASSIS BLOCK ASSEMBLY ··········· 6-7 6-2. ELECTRICAL PARTS LIST ·········································· 6-8 Parts list of the MS-95 board are not shown. Pages from 6-10 to 6-11 are not shown.
--5--
GV-D1000/D1000E
COVER
1-1. SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
SECTION 1 SERVICE NOTE
In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal, the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1: Use the DC IN terminal. (Use the AC power adaptor. (AC-L10, AC-VQ800 etc.)) Method 2: Connect the adjustment remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the HOLD switch to the "ADJ" side.
2.
1 2 3 4 5
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
Remove the power supply (Battery or AC power adaptor). Push the EJECT switch and open the cassette lid. Refer to 2-4. to remove the cabinet (lid) assembly. Refer to 2-4. to remove the cabinet (bottom) assembly. Add 5V from the regulated power supply between ULD 5V + (Pin 3, 4 of CN936) and ULD 5V (Pin 1, 2 of CN936), and unload the cassette.
ULD5V
+
VC-275 board
Regulated power supply (+5V)
1-1
GV-D1000/D1000E
1-2. SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTION 2. SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the LCD screen what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
LCD screen or monitor TV
C:31:11
When problems occur while the unit is operating, the counter of the LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
Blinks at 3.2Hz
C
Repaired by: C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
31
Block
11
Detailed Code
Refer to page 1-3. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
3.
SERVICE MODE DISPLAY
The service mode display shows up to six self-diagnosis codes shown in the past. 3-1. Display Method While pressing the "STOP" key, set the POWER switch from OFF to ON, and continue pressing the "STOP" key for 10 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
LCD screen or monitor TV
[3] C : 3 1 : 1 1
Lights up
[3]
Backup No. Order of previous errors
C:31:11
Control dial
self-diagnosis codes
3-2. Switching of Backup No. By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time 3-3. End of Display Turning OFF the power supply will end the service mode display.
Note: The "self-diagnosis display" data will be backed up by the coin-type lithium battery of FP-571 flexible board. When this coin-type lithium battery is removed, the "self-diagnosis display" data will be lost by initialization.
1-2
GV-D1000/D1000E
4.
Repaired by:
SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code Block Detailed Function Code 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4 0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2 Symptom/State Correction
C C C C C C C C C C C C C C C C C C C C C C C
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning.
1-3E
GV-D1000/D1000E
COVER
SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. LCD cabinet assembly PD-130 board service position
2-2. PD-130 board, LS-56 board
2-3. LCD window cabinet assembly (LCD901, ND901, SP901, SP902) 2-4. Bottom cabinet assembly, FP-571 flexible board (V/L rechargeable battery)
GV-D1000/D1000E
2-5. VC-275 board
2-6. Battery terminal board
2-8. MS-95 board
2-7. FP-575 flexible board (LANC), PR-41 board, IO-69 board
2-9. Mechanism deck
2-12. MS connector, FK-81 board
2-10. EJ-35 board
2-11. EX-39 board
2-13. FP-602 flexible board (DV IN/OUT), LCD block assembly
2-14. Hinge unit , FP-569 flexible board
[SERVICE POSITION TO CHECK THE VTR SECTION (Mainly for voltage measurement and check)] (VC-275, MS-95, IO-69, PR-41 boards, Mechanism deck)
[CONNECTION OF EQUIPMENT]
Adjustment remote commander (RM-95) AC power adaptor AC IN
2-1
GV-D1000/D1000E
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD CABINET ASSEMBLY
2 Two screws (M2 × 4), lock ace, p2 6 Remove the LCD cabinet assembly in the direction of the arrow.
3 Two screws (M2 × 3), lock ace, p2 1 Two screws (M2 × 4), lock ace, p2 4 Two claws 5 Two claws
[PD-130 BOARD SERVICE POSITION]
Multi-CPC jig (J-6082-311-A)
Touching here is safe when the machine is normal. However touching here can be dangerous if defective parts exist. LANC jack
CN5607
Caution : High voltage
0 3 -1 d D r P oa B
Adjustment remote commander (RM-95)
1 2 10 9
PD-130 board
CN5502 AC IN AC POWER ADAPTOR LS-56 board CN001 (2P) When the hinge unit is closed to be laid down, remove CN001 (2P) on the LS-56 board. If not, the main power cannot be turned on.
2-2
GV-D1000/D1000E
2-2. PD-130 BOARD, LS-56 BOARD
9 Three screws (M2 × 3), lock ace, p2 4 Harness (EP-51) (2P)
2 Two tapping screws (B2 × 6) 3 FP-569 flexible board (26, 32P)
P Bo D-1 ar 30 d
0 Remove the PD-130 board in the direction of the arrow.
1 Harness (PL-53) (2P)
qd LS bracket
qf LS-56 board
qs Screw (M2 × 3), lock ace, p2 qa Screw (M2 × 3), lock ace, p2 5 SP902 (2P) 7 ND901 (10P) 8 LCD901 (24P) 6 SP901 (2P)
2-3
GV-D1000/D1000E
2-3. LCD WINDOW CABINET ASSEMBLY (LCD901, ND901, SP901, SP902)
1 Two tapping screws (B2 × 6) 2 Two tapping screws (B2 × 6)
5 PD frame
4 LCD ground plate 3 Screw (M2 × 3), lock ace, p2
6 LCD901
9 ND901
7 Two claws
8 Two claws
REMOVING THE LCD WINDOW CABINET ASSEMBLY (SP901, 902)
1 Tapping screw (B2 × 6)
5 Tapping screw (B2 × 6) 3 SP ground plate 6 SP ground plate 4 SP902 7 SP901 2 Remove the SP ground plate in the direction of the arrow. Dowel
8 LCD window cabinet assembly
Claw
2-4
GV-D1000/D1000E
2-4. BOTTOM CABINET ASSEMBLY, FP-571 FLEXIBLE BOARD (V/L RECHARGEABLE BATTERY)
7 Bottom cabinet assembly 3 Three MI screws (M2 × 4) (H) 4 Three MI screws (M2 × 4) (H) 6 Open the jack lid assembly in the direction of the arrow B. B 2 Press the release button to remove the cabinet lid assembly in the direction of the arrow A. 5 MI screw (M2 × 4) (H) A 0 FP-571 flexible board (4P) (V/L rechargeable battery)
VC -2 75 Bo a rd
C 8 Tapping screw (+k 2 × 6)
1 Open the LCD panel little. 9 Remove the lithium lid in the direction of the arrow C.
2-5. VC-275 BOARD
9 Three screws (M2 × 3), lock ace, p2
0 Three screws (M2 × 3), lock ace, p2 qf DBB button
qa Remove the VC-275 board in the direction of the arrow. D C B
qd Switch cover assembly
A
qs Claw 1 Two FP-404 flexible boards (60P) D C B 7 FP-569 flexible board (26, 32P) A 8 FP-247 flexible board (50P)
2 FP-570 flexible board (40P) 3 Harness (PL-53)
6 Harness (EP-51) 4 FP-602 flexible board (5P) 5 Flexible flat cable (5P)
A Flexible board (from DRUM HEAD) (10P) B Flexible board (from MD MOTOR) (10P) C Flexible board (from MD SENS) (27P) D Flexible board (from MD CAP) (27P)
2-5
GV-D1000/D1000E
2-6. BATTERY TERMINAL BOARD
3 Battery frame 5 Battery terminal board
4 Battery panel assembly
2 Two MI screws (M2 × 4) (H)
1 MI screw (M2 × 4) (H)
2-7. FP-575 FLEXIBLE BOARD (LANC), PR-41 BOARD, IO-69 BOARD
1 Three tapping screws (B2 × 6) 8 Board to board connector (10P) qa Screw (M2 × 3), lock ace, p2 4 Cabinet (R)
7 Screw (M2 × 3), lock ace, p2 9 PR-41 board 3 Five tapping screws (B2 × 6) A A 0 Two MI screws (M2 × 4) (H)
qd IO-69 board (Note) qs Jack frame 6 FP-575 flexible board (6P)
5 Screw (M2 × 3), lock ace, p2 2 FP-247 flexible board (50P) Note: To remove the IO-69 board, remove the PR-41 board beforehand.
2-6
GV-D1000/D1000E
2-8. MS-95 BOARD
3 Two FP-404 flexible boards (60P) 2 Two screws (M2 × 3), lock ace, p2 4 MS-95 board
1 FP-405 flexible board (10P)
2-9. MECHANISM DECK
1 Screw (M2 × 3), lock ace, p2 3 Harness (EX-CB) A 4 Two tapping screws (B2 × 6) qs MD frame 8 Ferrite bead 6 Tapping screw (B2 × 6) 9 Screw (M2 × 3), lock ace, p2 A qg Mechanism deck 0 FC holder qf Cassette compartment cover 7 FP-405 flexible board (10P) FC holder 2 Screw (M1.4 × 1.5) qa Three screws (M1.4 × 1.5) 5 Tapping screw (B2 × 6)
PRECAUTION DURING INSTALLATION
MD frame Ferrite bead
qd Two screws (M1.7 × 3), lock ace, p2
2-7
GV-D1000/D1000E
2-10.EJ-35 BOARD
1 Two MI screws (M2 × 4) (H)
2 Cassette lid assembly
A 3 Press the cassette EJECT button in the direction of the arrow A and open the Lid frame assembly.
4 Four tapping screws (B2 × 6)
6 Harness (PL-53)
8 EJ-35 board
5 Lid frame assembly
7 Screw (M2 × 3), lock ace, p2
2-8
GV-D1000/D1000E
2-11.EX-39 BOARD
1 Tapping screw (B2 × 6)
4 FP-570 flexible board 3 Lid lock assembly 9 EX-39 board
7 Two screws (M2 × 3), lock ace, p2
8 EX frame
2 Two MI screws (M2 × 4) (H)
5 MI screw (M2 × 4) (H)
6 Harness (EP-51)
2-9
GV-D1000/D1000E
2-12.MEMORY STICK CONNECTOR (10P), FK-81 BOARD
1 Three screws (M1.7 × 3), lock ace, p2 3 Memory stick connector (10P)
2 FP-405 flexible board (10P) 4 Four tapping screws (B2 × 6)
7 FK frame
8 FK-81 board
6 Three screws (M2 × 3), lock ace, p2 5 Flexible flat cable (FFC-322) (10P)
2-10
GV-D1000/D1000E
2-13.FP-602 FLEXIBLE BOARD (DV IN/OUT), LCD BLOCK ASSEMBLY
8 Hinge retainer bracket (R)
4 Hinge retainer bracket (L)
5 FP-602 flexible board (5P) 3 Two screws (M2 × 3), lock ace, p2
7 Two dowels
6 Two MI screws (M2 × 4) (H) 1 Two MI screws (M2 × 4) (H) 0 Claw
2 Dowel qa Remove the LCD block assembly in the direction of the arrow A.
A
9 Claw D
qg Shaft cover (R)
qd Remove the shaft cover (R), shaft cover (L) in the direction of the arrow C D. C qf Shaft cover (L) Claw
B
qs Open the LCD block assembly in the direction of the arrow B.
2-11
GV-D1000/D1000E
2-14.HINGE UNIT, FP-569 FLEXIBLE BOARD
When attaching the hinge unit, wrap the FP-569 flexible board hinge shaft as shown while taking care so that the flexible board must not be caught or pinched. Hinge unit FP-569 flexible board (26, 32P) 3 FP-569 flexible board (26, 32P) 4 Hinge unit
Hinge shaft
1 Two tapping screws (B2 × 6) LS-56 board
Hinge unit Harness (EP-51) (2P) Hinge shaft
0 3 -1 D rd P oa B
2 Harness (PL-53) (2P)
When attaching the hinge unit, route the harness through the notch as shown while taking care so that the harness must not be caught or pinched.
Harness (EP-51) (2P)
2-12
GV-D1000/D1000E
[SERVICE POSITION TO CHECK THE VTR SECTION (Mainly for voltage measurement and check)] (VC-275, MS-95, IO-69 PR-41 BOARDS, MECHANISM DECK) Connection to Check the VTR Section Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Adjustment remote commander (RM-95) Battery terminal board LANC jack IO-69 board AC POWER ADAPTOR
AC IN
Mechanism deck
PR-41 board
FP-247 flexible board (50P)
1 20
CPC-13 jig (J-6082-443-A)
V Bo C-2 ar 75 d
Insulation sheet Insert an insulation sheet between the MD block and the VC-275 board.
1 20
VC-275 board
M Bo Sar 95 d
FP-404 flexible board (60P)
When you eject the cassette, connect Pin 1 and Pin 2 (GND) of CN938 on VC-275 board for 1 second.
2
CN938
MS-95 board
1
2-13
GV-D1000/D1000E
2-15.CIRCUIT BOARDS LOCATION
PD-130
FP-602 EJ-35 LS-56 EX-39 FK-81 FP-575
MS-95
IO-69 VC-275 PR-41
NAME EJ-35 EX-39 FK-81 FP-575 FP-602 IO-69 LS-56 MS-95 PD-130 PR-41 VC-275
FUNCTION EJECT SWITCH MULTI CONNECTOR CONTROL SWITCH BLOCK LANC DV IN/OUT AV IN/OUT LCD SWITCH CAMERA CONTROL, Y/C PROCESS, DIGITAL STILL CONTROL, MEMORY LCD DRIVER, BACK LIGHT REMOTE COMMANDER RECEIVER DV SIGNAL PROCESS, VIDEO SIGNAL PROCESS, AUDIO SIGNAL PROCESS, MECHA/HI CONTROL, SERVO, DC/DC CONVERTER
2-14
GV-D1000/D1000E
2-16.FLEXIBLE BOARDS LOCATION
The flexible boards contained in the mechanism deck are not shown.
Flexible flat cable (FFC-322) FP-570 FP-569
FP-571
FP-404 FP-247 FP-405
2-15E
GV-D1000/D1000E
COVER
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/5) OVERALL BLOCK DIAGRAM (2/5) OVERALL BLOCK DIAGRAM (3/5) OVERALL BLOCK DIAGRAM (4/5) OVERALL BLOCK DIAGRAM (5/5) POWER BLOCK DIAGRAM (1/3) POWER BLOCK DIAGRAM (2/3) POWER BLOCK DIAGRAM (3/3)
GV-D1000/D1000E
COVER
SECTION 3 BLOCK DIAGRAMS
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/5)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
IO-69 BOARD (1/2)
J402 S VIDEO IN Y C 32 31 CN402 30 29
VC-275 BOARD(1/4)
(4/13)
(4/13)
(1/5)
MS-95 BOARD (1/2)
IC3702
CN922 11 EX Y/V IN 5 14 16 EX C IN 3 1 8 6 9 J401 S VIDEO OUT Y C 20 18 19 17 Y C 18 14 Y C V 39 48 42
IC3701
LINE IN LINE OUT AGC ACC 36 34 CN939 Y 50 C 51 CN102 50 51 2 6
IC701
A/D CONVERTER 59 Y0-Y7 52 49 C0-C7 42 38 HD,VD,OE 37 36 34 68 31 65 66 64 63 TO OVERALL BLOCK(2/5) AFCK SPCK (IC302) XCS IC701 (IC1104 of VC-275) TO OVERALL BLOCK(2/5)
(PAGE 3-3)
Q3702
EX VIDEO OUT J403 VIDEO OUT L AUDIO OUT R V L R 16 12 10 15 11 V 22
HI SO,SI,SCK 9
(PAGE 3-3)
J1701 AUDIO/VIDEO INPUT J1702 (HEADPHONES)
L V R 9 10 HP L HP R 11
46 7
Y (IC3301) C (IC3301)
XCS IO (IC4702) VSP SO,SI,SCK XCS AU1 (IC4702) EX AUDIO L OUT EX AUDIO R OUT 15 14 13
(9/13)
L R HP L HP R 54 55 64 2
(9/13)
IC6101
AUDIO I/O 25 23 19 17 L R L R 3 2 15 16
IC6001
AUDIO A/D CONV. D/A CONV. 8 9 12 DATA TO SFD DATA FROM SFD SFD BCK TO OVERALL BLOCK(2/5)
(9/13)
(PAGE 3-4)
EX-39 BOARD(1/2)
3 20 1 15 14 6 5 2 19 13 17 15 6 4 CN201 2 19 13 17 15 6 4 EX EX EX EX EX EX EX Y/V IN C IN VIDEO OUT AUDIO L OUT AUDIO R OUT AUDIO L IN AUDIO R IN
IC6103
AUDIO L IN AUDIO R IN EX AUDIO L IN 1 4 8 EX AUDIO R IN 11 2 3 9 10 L R 51 53
62 63
L R
CN203 MULTI CONNECTOR
4
CN931
(9/13)
CN5506 SP901 SPEAKER(L) 1 2 CN5503 2 1 26 25 CN5505 25 26 1 2 SP L+,L- 7 4
(9/13)
(9/13)
IC6102
SPEAKER AMP 9 11 1 7
IC6105
BEEP MIX 3 5 2 6 2 3 10 9
IC6104
MUTE 1 11 L R MIX 11 CN940
BEEP
TO OVERALL BLOCK (5/5)
(PAGE 3-10)
SP902 SPEAKER(R)
1 2
PD-130 BOARD(1/3)
SP R+,R- 13 16 CN923
KASYAON
TO OVERALL BLOCK (2/5) (MS-95)
16
(PAGE 3-3)
3-1
3-2
GV-D1000/D1000E
COVER
3-2. OVERALL BLOCK DIAGRAM (2/5)
MS-95 BOARD(2/2)
36 272
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN103
10 9 10 9
CN940 SPCK AFCK
199 · 201 203 · 205 207 · 211 213 · 215 1·3 5·7 17 · 21 · 23 200 · 202 204 · 206 208 · 212 214 · 216 2·4·6 8 · 9 · 11 13 · 15 18 · 22 · 24 135 134 127 · 128 196 48 8
(2/13)
138 139 142
VC-275 BOARD(2/4)
X3301 24.576MHz (3/13)
45
CN101 (DV) IN/OUT
48
48
IC3301
DV SIGNAL PROCESS
Y0 Y7
28 45
(3/5)
265 276 273 1 · 2 · 3 27
Y0Y7
41 40 41 40
Y0Y7
C0 C7 HD,VD,OE TO OVERALL BLOCK (1/5)
IC361
Y/C PPOCESS
L BUS
145 52 51 141 42
IC3303
DV INTERFACE
6 9 29 37
TPA+, TPB+,
CN929
2 5
C0C3
37 37 28 · 27 · 29 56 49 36
38 46 · 47 · 48
C0C3
28 · 27 · 29 56
TRCK LCK
47 79
HD,VD,OE
HD,VD,OE
MC BUS
FP-602
(FLEXIBLE)
AFCK
49
Y0Y7
18 16 12
49 36
Y0Y7
152 · 153 · 156 133 132 127 99 97 167 83
FRRV,TRRV,TRRT DATA TO SFD DATA FROM SFD SFD BCK REC CK REC DT SWP(IC4702) AD DT 6 PB CK TO OVERALL BLOCK (3/5)
(PAGE 3-2)
SPCK (1/5) CS CAM (IC452)
3
C4C7
33 33 30 · 31 · 32 23 24 25
C4C7
30 · 31 · 32 23 24 25
9 · 10 · 11 7 25 24 33 · 34 · 35
HD,VD,OE DATA TO SFD2 DATA FROM SFD2 SFD BCK
HD,VD,OE DATA TO SFD2 DATA FROM SFD2 SFD BCK AFCK (ON940) SPCK (CN940) HD VD
HI SO, SI,SCK
IC302
TIMING GENERATOR
SPCK CH
160 158 124 · 123 · 122
6 5
6
88 81 79 170
(PAGE 3-5)
2 · 47 · 1
HD,VD,FLD
(2/13)
30 29
IC3302
CHARACTER GENERATOR
180
20 · 19
184 · 183 195 · 194 · 191 · 190
MC BUS
179 159 161 163 162
X301 54MHz GV-D1000 40.5MHz GV-D1000E (5/5)
20
18 COLO · 17 COL3 · 16 · 14
VSP SO,SI,SCK
XCS OSD OSD SO XOSD SCK XCS SFD (IC4702) XCS VFD (IC4702)
TO OVERALL BLOCK (5/5)
IC391
SDRAM
A0A13
35 2 13 · 42 53 209 164
13
D0 D15
191
TO OVERALL BLOCK (1/5)
XCS OSD CSD SO XOSD SCK Y (IC3301) C (IC3301) DATA TO SFD DATA FROM SFD SFD BCK VSP SO,SI, SCK L R
55 59
75 PANEL G 73 PANEL B 71 105 PANEL HD,VD · 106
PANEL R
FRRV, TRRV, TRRT ATF ERR
(PAGE 3-10)
MC BUS
(PAGE 3-2)
CAM SO,SI,SCK
62 · 61 · 60 52
TO OVERALL BLOCK (3/5)
XCS IC361 (IC4702)
(PAGE 3-5)
VSP SO,SI,SCK PANEL R PANEL G PANEL B
67 · 56 · 54 38
CN923
22 21 20 16
(IC452) CS CAM (2/5)
17 · 16
59
56 · 54 · 53
VSP SO,SI, SCK
15 · 16 · 14
15 · 16 · 14
VSP SO,SI, SCK
PANEL HD,VD 17
55
TO OVERALL BLOCK (4/5) (PD-130)
IC453
EVR
YO Y7
49 34
(5/13)
SYRB DA (IC452)
15
IC2001
MPEG ENCODER
XCS IC2001 (IC4702)
(PAGE 3-7)
C4 C7 HD,VD,OE
3 · 4 · 2
37 24 · 25 · 33
(2/5)
(5/13) L R
8
IC451
EEPROM AUCLK (IC1407)
3 2
IC2003
AUDIO A/D CONV.
XCS EEPROM (IC452)
1
9 11
SDT MCLK SPCL (CN940) LCK (IC3301)
57 47 30 · 32 52
64 · 63
USB D+, D
KASYA ON
22 28
151
X2001 48MHz
3, 2 D+, D
CN1701 (USB)
33 · 34 · 35
(2/5)
(5/5)
(5/5)
IC452
CAMERA CONTROL
IC1406
4Mbit FLASH MEMORY
1 25 48 226 215 29 45
IC1404
16Mbit SDRAM
19 32 2 12 39 49 54
(4/5)
(4/5)
143 140 13 · 12 · 4 · 5
IC1407
DIGITAL STILL CONTROL A0 A20
IC1405
USB I/F
11 · 10
CN102
13 · 14 13 · 14
CN939 USB D+, D
TO OVERALL BLOCK (1/5) (VC-275)
KASYA ON
CN103
11
CS CAM XCS EEPROM STRB DA XCS CAM (IC1104 of VC-275)
98 28 97 47
A0 A11
129 77 52
UCLK
1 4 XTAL
OSC
X1402 48MHz (4/5) BS DIO SCLK
(PAGE 3-2)
48 · 49 · 50
254
D0 D15
227
IC1403
155 156 187
34
LED DRIVE TO OVERALL BLOCK (5/5) (VC-275) XACCESS LED HI SO,SI,SCK CN102
22 5 · 6 · 8
LED ON AUCLK
13 159 171 · 164 · 165
X1401 25.8048MHz MS BS,DIO,SCLK
CN101
8 · 6 · 4
Q1408 HI SO,SI,SCK
185
MEMORY STICK
FP-405
(FLEXIBLE)
(PAGE 3-10)
(IC1104) XCS DS
170
3-3
3-4
GV-D1000/D1000E
COVER
3-3. OVERALL BLOCK DIAGRAM (3/5)
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN933 FOR ADJUSTMENTS 17 20 RF MON
J MECHA DECK
(1/13)
REC CK REC DT 40 42 REC/PB AMP 42 PB Y OUT 27
VC-275 BOARD(3/4)
REC CK REC DT
SWP
IC3103
6 7 2 1
CN3101 ODD 5 6 EVEN 8 9 DRUM HEAD
(1/13)
AD DT 6 AD DT 6 20 TO OVERALL BLOCK (2/5) EQ A/D CONV. PLL 15
IC3101
PB CK
PB CK
13 34
22 24
25
31 SWP
(PAGE 3-4)
ATF ERR 95 60 79 DRP SO,XDRP SCK 78 MC BUS FRRV TRRT,TRRV
SWP(IC3301) XCS TRF (IC4702)
(6/13)
M902 CN937 14,15 CAP FG CAP ON,CAP FWD 2,3 32 FG 1,2 22 25 CAPSTAN FG
IC4702
MECHA CONTROL
115 45 46
CAPSTAN FG AMP
VSP SO,SI,SCK
(7/13)
(6/13)
26 | 36 FRRV TRRT TRRV 106 | 108 74 | 76 68 DRUM PWM 28 29 DRUM ERROR 15 LPF 1 X4701 20MHz 2 58 LPF PWM DRIVE Q1306 DRUM VS SWITCHING 6 69 CAP PWM 25
IC4701
EEPROM 1 2-4
(7/13) (12/13)
IC1002
Q1305 CAP VS SWITCHING 64 18,22 CAPSTAN MOTOR DRIVE
17 | 20 21,23,19 CAP U,V,W 1 | 4 11 | 14 CN934 M901 5 DRUM U,V,W | 10
M
CAPSTAN MOTOR
IC1001
(2/2)
27
CAP ERROR 11
IC1301
(2/2)
(7/13)
61,59,57
M
DRUM MOTOR
IC1001
(1/2) DRUM MOTOR DRIVE DRUM FG SENS
2
DRUM FG
XCS EEP
88 83
70 DRUM ON,DRUM FWD,DRUM START 98 63 DRUM FG 16 DRUM FG AMP 17 1,11,14 DRUM PG SENS 1 DRUM PG
TO OVERALL BLOCK (5/5)
HI SO,SI,SCK
82 81 XCS MECHA (IC1104) 72
116
(PAGE 3-10)
CHIME SDA,SCK,VDD XCC DOWN
117 XCS VFD (IC3301) XCS IO (IC3701) XCS AU1 (IC6101) XCS TRF (IC3101) XCS SFD (IC3301) XCS IC361 XCS IC2001 17 18 21 23 40 114 71 111 113 41 42
DRUM PG
22 DRUM PG AMP
20 CN936
M903 1 | 4
LOAD,UNLOAD
55,56
LOADING MOTOR DRIVE
53,51
LM +,
M
DEW SENSOR
LOADING MOTOR
TREEL FG SREEL FG
41 33 REEL FG AMP
38,39 36,35 5
54
TAPE END
47 TAPE END DETECT
46
T REEL +,
20 21
T REEL SENSOR
H902
53
TAPE TOP
44 TAPE TOP DETECT
45
S REEL +,
24 23
S REEL SENSOR
H901
96
DEW DET TAPE END C TAPE LED ON 25
Q901 TAPE END SENSOR
55
TAPE TOP C 44 REC PROOF SW
Q902 TAPE TOP SENSOR 27
47 | 49
MODE SW A - MODE SW C 12
D901 TAPE LED
REC PROOF 15 16 4PIN | 18 XCC DOWN 11 CC DOWN 7 | 9 MODE SWITCH S902 S903 CONNECTOR CN901 S901
16
3-5
3-6
GV-D1000/D1000E
COVER
3. BLOCK DIAGRAMS
3-4. OVERALL BLOCK DIAGRAM (4/5)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
PD-130 BOARD(2/3)
CN5502 S/C R5553 8.2K GND HD OUT PANEL COM VR,VG,VB 6 10 8 4 5 3 1 19 20 21 VCOM VGLAC 11 4 5 10 12 18 CN5501 CPC FOR ADJUSTMENTS
PANEL R PANEL G PANEL B TO OVERALL BLOCK (2/5) (VC-275)
5 6 7
48 47 46 41 40 39
IC5501
RGB DRIVE
20 VR,VG,VB 22 24 27 COM DA
LCD901 4INCH LCD UNIT ND901 BACKLIGHT BL HIGH 10 T5601 Q5602 INVERTER BACK LIGHT DRIVE BL REG
(1/2)
35
(PAGE 3-4)
PANEL HD PANEL VD
10 11
(2/2)
44 HI SO, SCK 13 15 46 45 42 1 48 XCS LCD
IC5502
TIMING GENERATOR
IC5602
BL LOW CN5604 3 3 CURRENT DET 4
12 24 Q5601 9
TO OVERALL BLOCK (5/5) (VC-275)
(1/2)
2 8 5
14
HD OUT
BL DET 5 1 6 PANEL 2.8V 2 7
(PAGE 3-10)
BL CONT 23 CN5503
(2/2)
IC5601
3-7
3-8
GV-D1000/D1000E
COVER
3-5. OVERALL BLOCK DIAGRAM (5/5)
FK-81 BOARD
CN301 S301318,320 S322 PHOTO SWITCH FUNCTION SWITCH S319 MPEG SWITCH D301 (MS ACCESS) 5 6 · · 4 7 · · 3 8 6 5 8 3 9 2 X PHOTO FREEEZE X MPEG X ACCESS LED
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-275 BOARD (4/4)
CN927
(8/13)
IC1104
HI CONTROL
PD-130 BOARD (3/3)
CN923 23 CN923 13 14 · 12 4 4 S5601, 5602 LCD BRIGHT AD6 1 SW CN5503 CN5608 XCS LCD HI SO, SCK BL CONT TO OVERALL BLOCK(4/5) (PD-130) 2
LS-56 BOARD
S001 LCD ON/OFF SW CN001
(8/13)
IC1101
EJ-35 BOARD
S101 EJECT CN101 2
FP-571
(FLEXIBLE)
BT001 VANADIUM/ LITHIUM BATTERY 1 · 2
X1101 20MHz X1102 32.768kHz 5
CN926 BATT LI 3V 3 VTR UNREG BATT UNREG 1 CN938 S1701 USB MODE 7
RESET
VDD SWITCH
6 S1001 RESET
IO-69 BOARD (2/2)
EXEC S401 SEL/PUSH EXEC DIAL 23 26 · 25
XCS MECHA 51 XCS DS 55 6 X PHOTOXCS 50 FREEZE 3 X MPEG XCS LCD 49 XCS CAM 176 XCC DOWN 5 69 20MHz OUT CHIME SDA 90·121 70 20MHz IN CHIME SCK 91·122 99 32kHz IN CHIME VDD 120 100 32kHz OUT 67 XRESET HI SO 53 · 17 HI SI 52 · · 73 HI SCK 54 · 71 VDD · 98 · XCS OSD 125 124 · · OSD SO 45 151 · XOSD SCK 46 4 XE JECT SW 130 KEY AD4 MELODY 157 131 KEY AD5 MELODY ENV 13 104 DIAL A · 105 DIAL B
126 KEY AD0 · 127 KEY AD1 · 128 KEY AD2
KEY AD6 132
XCS MECHA (IC4702) XCS DS (IC1407) XCS IC701 XCS LCD (IC5501, 5502) XCS CAM (IC452)
(PAGE 3-7)
CN939 22 5 · 6 · 8 XACCESS LED HI SO, SI SCK TO OVERALL BLOCK(2/5) (MS-95)
(PAGE 3-3)
HI SO, SI, SCK XCS OSD OSD SO XOSD SCK
HI SO, SI SCK XCC DOWN TO OVERALL BLOCK(2/5) CHIME SDA, SCK, VDD
TO OVERALL BLOCK(3/5)
(PAGE 3-5)
(PAGE 3-4) (12/13)
Q1110,1111 MOD BEEP TO OVERALL BLOCK(1/5)
VCR MEMORY STICK
CN922 24 25 · 26
IC1301,1302,1303
DC-DC CONVERTER (2/2) BL CONT
(PAGE 3-2)
PR-41 BOARD
(FLEXIBLE)
(POWER ON) (CHARGE)
D505 3 · 4 5 · 6 3 · 4 5 · 6 X POWER LED X CHARGE LED 46 43 45
Q1117,1118 LED DRIVE 44
BATT/EXT SW FAST CHARGE VTR DO ON SHOE ON 9 POWER LED
171 85 26 21
IC502
REMOTE COMMANDER RECEIVER
14 CHARGE LED ON
8 8 CN501
SIRCS SIG CN104
45
46
D1711 (SIRCS EMITTER) SIRCS PWM
86 SIRCS SIG Q1101,1104,1105,1108 89 SIRCS ENV MOD 20 IR ON
J001 (LANC)
FP-575
(FLEXIBLE)
S001 POWER ON
BL REG PANEL -15.3V PANEL 13.3V PANEL 2.8V AU 2.8V A 2.8V D 2.8V D 1.5V D 1.6V D 1.9V AU 4.6V A 4.6V RP 4.6V PANEL 4.6V MT 4.9V EX UNREG SHOE ON Q2507 CN2501 Q2502 4 3 2 6 5 1 DC IN BT901
OFF(CHG)
1 1 2 2 LANC SIG CN401 CN402
2 1
1 2
1 X VTR MODE SW 115 ID1 · 116 ID2 88 IB SI · 87 IB SO LANC IN 82 · LANC OUT 83 Q1109
VTR DO ON VTR UNREG BATT UNREG
EX-39 BOARD(2/2)
11, 17 CN203 18, 19 MULTI CONNECTOR 8 LANC SIG CN201 10 · 11 23 | 26 8 10 ID1,ID2 · 11 23 EX UNREG | 26 8 CN931
(8/13)
IF
BATT SIG
IC1105
LANC SIG 10 11 LANC I/O · 12
FAST CHARGE BATT/EXT SW BATT SIG
+
S
BATTERY TERMINAL
16
3-9
3-10
GV-D1000/D1000E
COVER
3-6. POWER BLOCK DIAGRAM (1/3)
VC275 BOARD (1/2)
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SHOE ON BT901 BATTERY TERMINAL CN2501 BATT UNREG Q2506, 2507 EX UNREG EX UNREG BATT SIG INIT CHARGE ON VTR DD ON FAST CHARGE F2501 BATT/XEXT SW BATT UNREG BATT UNREG BATT UNREG
6
S
1 5
BATT GND BATT SIG
Q2501, 2502
F2502 Q2503,2504 CHARGE SWITCH F2504 F2505
C/D VS D1.5V BL UNREG VTR UNREG
5V REG Q13101313
MT 4.9V
MT 4.9V
DC IN 4 3 2 ACV UNREG ACV GND BATT/XEXT SW
F2503
VTR UNREG
VTR UNREG
EX UNREG L2501
INIT CHARGE ON
BL CONT
BL CONT
BL CONT
FAST CHARGE
SHOE ON
(12/13)
IC1301
DC/DC CONVERTER
Q1309 SWITCHING
L1317
L1318
BL REG
BL REG PANEL 2.8V
(458)
7
IC1303
Q1330 D 1.6V
NONINV INPUT7
PANEL 13.3V PANEL 15.3V PANEL 4.6V
OUTPUT7 OUTPUT MONITOR-7 OUTPUT VCC7 OUTPUT VCC4,5,6 OUTPUT4
2 6
1.6V REG
31 STANDBY7
(458)
Q1303 SWITCHING
5 1 57 54
IC1302
L1305 L1321 Q1328 1.5V REG Q1308 SWITCHING L1310 L1306 L1307 D 1.5V
TO POWER BLOCK(2/3)
(PAGE 3-13)
28 VCC
D 1.9V AU 4.6V D 2.8V A 2.8V AU 2.8V PANEL 2.8V A 2.8V AU 2.8V D 1.5V D 1.9V
MOS GATE4
OUTPUT MONITOR4 18 COMP
41
Q1304 SWITCHING
L1302
L1308 L1309
OUTPUT1 MOS GATE1 OUTPUT MONITOR1
45 42 40
Q1307 SWITCHING
Q1314 EMERGENCY DETECT
T1301 OUTPUT VCC1,2,3 VREF
27 VREF 49
Q1301 SWITCHING
4
D1301 (1/2) RECT
5 6 7 8 2
PANEL 13.3V
OUTPUT3 OUTPUT MONITOR3
50 34
1
D1301 (2/2) RECT
D1302 RECT L1313 L1314
Q1322, 1324, 1326 -15.3V REG AU 4.6V A 4.6V PANEL 4.6V RP 4.6V PANEL -15.3V
A 4.6V D 2.8V PANEL 13.3V
21 RT 22 CT
3
Q1302 SWITCHING
L1301
OUTPUT2 VTR DD ON
46
CAP VS CAP ERROR DRUM VS DRUM ERROR
L1315 L1316
29 STANDBY3 30 STANDBY
OUTPUT MONITOR2
37
Q1305 SWITCHING
L1303
CAP VS
CAP VS CAP ERROR DRUM VS
RP 4.6V D 3.1V
OUTPUT6 OUTPUT MONITOR6 NONINV INPUT6
64 10 11
CAP ERROR Q1306 SWITCHING DRUM ERROR L1304 DRUM VS 39 41 30 32 26 28 35 37 DRUM ERROR 27 29 38 40 31 33 A 2.8V D 2.8V D 1.6V PANEL 13.3V D 1.9V A 4.6V D 3.1V TO POWER BLOCK (3/3) (MS-95)
OUTPUT5 58 OUTPUT MONITOR5 14 NONINV INPUT5 15
(PAGE 3-15)
16
CN939
3-11
3-12
GV-D1000/D1000E
COVER
3-7. POWER BLOCK DIAGRAM (2/3)
VC-275 BOARD(2/2)
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
BT001 VANADIUM/ LITHIUM BATTERY
BATT LI3V CN926
1 2
FP-571 (FLEXIBLE)
IC1104 (8/13)
HI CONTROL SHOE ON BATT SIG INIT CHARGE ON VTR DD ON FAST CHARGE BATT/ XEXT SW BATT UNREG SHOE ON 21 112 BATT SENS 113 ACV SENS Q1109 IB SO 87 IB SI 88 INIT CHARGE ON 24 VTR DD ON 26 FAST CHARGE 85 BATT/XEXT 171 XVTR MODE SW 1 Q1118 LED DRIVE Q1117 LED DRIVE 22 45 44 47 21 46 43 48 EVER 3.0V XPOWER LED XCHARGE LED A 4.6V CN402 CN403 CN501 1 2 3 4 5 6 7 1 2 3 4 5 6 7 D505 (POWER ON) (CHARGE) I/F BATT SIG CN922 1 5 2 6
IO-69 BOARD
XVTR MODE SW LANC DC CN401 1 6
S001 POWER ON OFF(CHG)
FP-575 (FLEXIBLE)
J001 (LANC)
(8/13)
D1106 2
IC1101 (8/13)
D1101 3 3 6 7 REG BATTER IN DETECT 4 8 Q1107 92 XLANC ON RESET 5 67 XRESET 17 71 73 124 VDD 98 151 80 BATT IN
IC1103
REG
MT 4.9V
IC1105 (8/13)
LANC I/O 1 UNREG LANC DC 14 LANC DC POWER 4 VCC 8
XPOWER LED 9 XCHARGE LED 14 CHIME PEW CONT 16
VTR UNREG EX UNREG BL CONT BL REG
IC502
PR-41 BOARD
S1011 RESET VTR UNREG MT 4.9V AU 4.6V
PANEL 2.8V PANEL 13.3V PANEL -15.3V PANEL 4.6V
PD-130 BOARD
(9/13) (9/13) (9/13) (9/13) (9/13) (9/13)
IC6101
AU 4.6V AUDIO I/O
IC6001
AUDIO ADC&DAC L6001
IC6103
AUDIO INPUT SELECT
IC6102
SPEAKER AMP
IC6104
SPEAKER MUTE
IC6105
BEEP MUTE
PANEL 4.6V PANEL -15.3V PANEL 13.3V PANEL 2.8V BL CONT
9 5 6 10 4 CN923
18 22 21 17 23
PANEL 4.6V PANEL -15.3V PANEL 13.3V PANEL 2.8V BL CONT CN5503
L5504 L5503 L5501 L5502
LCD901 24 3 1 23 CN5501
4INCH LCD UNIT
(1/2)
IC5501
IC5502
TIMING GENERATOR ND901 BACKLIGHT
D 1.9V A 2.8V TO POWER BLOCK (1/3) AU 2.8V
A 2.8V AU 2.8V D 2.8V FB3701 FB3302
FK-81 BOARD
FB3303 CN301 D 2.8V CN927 EVER 3.0V 1 10 LED
RGB DRIVE
(1/2)
(PAGE 3-12)
D 1.5V
IC5601,5602
IC3701
VIDEO LINE IN/OUT AMP L3701, 3705
IC3301
DV SIGNAL PROCESS
IC3303
DV INTERFACE
IC3302
CHARACTER GENERATER
D1711 SIRCS EMITTER BL REG 34 36 23 34 36 23 26
EX-39 BOARD
1 CN202
2
BL REG CN5607
INVERTER BACKLIGHT DRIVE
BL HIGH
10
(2/2)
CN5604
(4/13)
(2/13)
(3/13)
(2/13)
F1701 EX UNREG
A 4.6V
D 2.8V
A 4.6V MT 4.9V A 2.8V D 1.5V D 2.8V
18 19 CN201
CN203 MULTI CONNECTOR
26 CN931
L3706 PANEL 13.3V CAP VS CAP ERROR DRUM VS DRUM ERROR
FB2003
FB2004
L2001
L3102 CHIME PWR CONT
IC3702
VIDEO INPUT SELECT
IC2001
MPEG ENCODER
IC2003
AUDIO A/D CONV.
IC3101
EQ, A/D CONV, PLL
IC3103
REC/PB AMP
(7/13) (6/13) (6/13)
IC4701
EEPROM
IC4702
MECHA CONTROL 105 DRUM ERROR 29 CAP ERROR 27 DRUM VS 6
IC1001
DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP
(4/13
RP 4.6V D 3.1V
(5/13)
FB2001
(5/13)
(1/13)
L3103
(1/13)
L3104
FB4701
D 2.8V VTR UNREG MT 4.9V
J MECHA DECK
D901 TAPE LED(A) 13 R1025 CN901 TAPE LED
PANEL 13.3V 18 CAP VS 22
IC1002
CAPSTAN MOTOR DRIVE CAP FG AMP XREEL HALL ON Q1106
CHIME VDD
18
4PIN CONNECTOR H901,902
SENSOR VCC
(7/13)
16
19
Q1002
CN936
SREEL TREEL SENSOR
3-13
3-14
GV-D1000/D1000E
COVER
3-8. POWER BLOCK DIAGRAM (3/3)
MS-95 BOARD
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
IC361
Y/C PROCESS
IC391
SDRAM
IC302
TIMINB GENERATOR
IC303
AMP
IC701
VIDEO A/D CONV.
IC452
CAMERA CONTROL
IC451
EEPROM
IC453
EVR
(3/5)
(5/5)
(1/5)
(1/5)
(1/5)
(2/5)
(2/5)
(2/5)
FB364, 365 A 2.8V D 2.8V D 1.6V PANEL 13.3V A 4.6V 39·41 30·32 26·28 35·37 38·40 D 2.8V
R305 FB363 L361 FB391 L302 FB305 L702 L701 L451 FB701 L452
FB1404
FB1406
FB1402
(4/5)
TO POWER BLOCK(1/3) (VC-275)
IC1404
SDRAM
IC1406
FLASH MEMORY
IC1407
DIGITAL STILL CONTROL FB1403, 1408 32 MS VCC ON
IC1403
XTAL OSC
IC1401
BUFFER
IC1405
USB I/F
(PAGE 3-12)
(5/5)
D 1.9V 27·29
(5/5)
(4/5)
(4/5)
(4/5)
FB1405
IC1408
D4.6V FB1409 2 · 5 3.1V REG 3 D3.1 FB1407 Q1412,1413 MS VCC
CN101 3 · 7 MEMORY STICK
(5/5)
D 3.1V 31·33 CN102
FP-405
(FLEXIBLE)
3-15
3-16E
GV-D1000/D1000E
COVER
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2)
1 2 3 4 5 6 7 8 9
CN939 60P REG_GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 REG_GND REG_GND REG_GND REG_GND HI_SO HI_SI XCS_CAM XHI_SCK XSYS_RST USB_D+PULLUP GND GUARD GND GUARD USB_D+ USB_DGND GUARD GND GUARD USB_DET DS_MAD XDS_RST XDS_WAKE_UP XCS_DS XACCESS_LED XDS_FLASH_RST MS_XIN AUDIO_MUTE_DS D_1.6V D_1.9V D_1.6V D_1.9V D_2.8V D_3.1V D_2.8V D_3.1V REG_GND PANEL_13.3V REG_GND PANEL_13.3V A_4.6V
10
11
CN102
12
60P
13
14
15
16
17
18
19
20
A
REG_GND REG_GND REG_GND HI_SO HI_SI
IO-69 BOARD B
CN402 50P LANC_SIG XVTR_MODE_SW REG_GND XLANC_JACK_IN REG_GND LANC_DC LCH_OUT_DET 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 LANC_SIG
FP-247
FLEXIBLE
CN002 50P CN001 50P XVTR_MODE_SW LANC_SIG XLANC_JACK_IN REG_GND LANC_DC REG_GND RCH_OUT_DET LCH_OUT_DET AUDIO_R_OUT REG_GND AUDIO_L_OUT RF_DC_OUT V_JACK_OUT_DET VIDEO_OUT_GND VIDEO_OUT S_C_GND S_C_OUT S_Y_GND S_Y_OUT REG_GND XS_JACK_OUT_DET EVER_3.0V XIR_LED_ON KEY_AD5 DIAL_A DIAL_B XS_JACK_IN_DET S_Y_GND S_Y_IN S_C_GND S_C_IN REG_GND AV_JACK_IN_DET VIDEO_GND VIDEO_IN REG_GND AUDIO_L_IN AUDIO_GND AUDIO_R_IN XHP_SENS HP_R HP_GND HP_L XCHARGE_LED XPOWER_LED SIRCS_SIG A_4.6V REG_GND REG_GND REG_GND 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 CN922 50P XVTR_MODE_SW LANC_SIG XLANC_JACK_IN REG_GND LANC_DC REG_GND RCH_OUT_DET LCH_OUT_DET AUDIO_R_OUT REG_GND AUDIO_L_OUT RF_DC_OUT V_JACK_OUT_DET VIDEO_OUT_GND VIDEO_OUT S_C_GND S_C_OUT S_Y_GND S_Y_OUT REG_GND XS_JACK_OUT_DET EVER_3.0V XIR_LED_ON KEY_AD5 DIAL_A DIAL_B XS_JACK_IN_DET S_Y_GND S_Y_IN S_C_GND S_C_IN REG_GND AV_JACK_IN_DET VIDEO_GND VIDEO_IN REG_GND AUDIO_L_IN AUDIO_GND AUDIO_R_IN XHP_SENS HP_R HP_GND HP_L XCHARGE_LED XPOWER_LED SIRCS_SIG A_4.6V REG_GND REG_GND REG_GND XVTR_MODE_SW REG_GND XLANC_JACK_IN REG_GND LANC_DC LCH_OUT_DET RCH_OUT_DET REG_GND AUDIO_R_OUT RF_DC_OUT AUDIO_L_OUT VIDEO_OUT_GND V_JACK_OUT_DET S_C_GND VIDEO_OUT S_Y_GND S_C_OUT REG_GND S_Y_OUT EVER_3.0V XS_JACK_OUT_DET KEY_AD5 XIR_LED_ON DIAL_B DIAL_A S_Y_GND XS_JACK_IN_DET S_C_GND S_Y_IN REG_GND S_C_IN VIDEO_GND AV_JACK_IN_DET REG_GND VIDEO_IN AUDIO_GND AUDIO_L_IN XHP_SENS AUDIO_R_IN HP_GND HP_R XCHARGE_LED HP_L SIRCS_SIG XPOWER_LED REG_GND A_4.6V REG_GND REG_GND
XCS_CAM XHI_SCK XSYS_RST USB_D+PULLUP GND GUARD GND GUARD USB_D+ USB_DGND GUARD GND GUARD USB_DET DS_MAD XDS_RST XDS_WAKE_UP XCS_DS XACCESS_LED XDS_FLASH_RST MS_XIN AUDIO_MUTE_DS D_1.6V D_1.9V D_1.6V D_1.9V D_2.8V D_3.1V D_2.8V D_3.1V REG_GND PANEL_13.3V REG_GND PANEL_13.3V A_4.6V A_2.8V A_4.6V A_2.8V REG_GND REG_GND REG_GND REG_GND AGC_CONT ACC_CONT REG_GND REG_GND IC3701_Y_OUT IC3701_C_OUT REG_GND REG_GND TD_2-3 TDO XCS_IC701 REG_GND REG_GND REG_GND REG_GND
MS-95 BOARD
1/5 2/5 3/5 4/5 5/5 CH,IN BLOCK CM BLOCK CA BLOCK MS1 BLOCK MS2 BLOCK
CN101 10P VSS VSS BS VCC DIO INS SCLK VCC VSS VSS 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 VSS BS VCC DIO N.C. INS N.C. SCLK VCC VSS MEMORY STICK CONNECTOR
FP-405
FLEXIBLE
C
J403 R AUDIO 0UT L (MONO) VIDEO OUT
RCH_OUT_DET REG_GND AUDIO_R_OUT RF_DC_OUT AUDIO_L_OUT VIDEO_OUT_GND V_JACK_OUT_DET S_C_GND VIDEO_OUT S_Y_GND S_C_OUT REG_GND J401 C S VIDEO OUT S G G S401 SEL/PUSH EXEC Y S S_Y_OUT EVER_3.0V XS_JACK_OUT_DET KEY_AD5 XIR_LED_ON DIAL_B DIAL_A S_Y_GND J402 C S VIDEO IN S G G Y S XS_JACK_IN_DET S_C_GND S_Y_IN REG_GND
10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 40 40 41 41 42 42 43 43 44 44 45 45 46 46 47 47 48 48 49 49 50 50
10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 40 40 41 41 42 42 43 43 44 44 45 45 46 46 47 47 48 48 49 49 50 50
FLEXIBLE
FP-404
D
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
E
A_4.6V A_2.8V REG_GND REG_GND REG_GND REG_GND AGC_CONT
CN103
60P
A_2.8V
S_C_IN VIDEO_GND AV_JACK_IN_DET
DATA_TO_SFD2
XCS_IC361
F FP-575
FLEXIBLE
CN401 6P POWER OFF/ON S001 J001 LANC 1 2 3 4 5 6 XVTR_MODE_SW LANC_SIG XLANC_JACK_IN REG_GND REG_GND LANC_DC
DATA_FROM_SFD2
XVSP_SCK
SFD_LRCK
IC361_ON
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND 59 59 REG_GND
REG_GND VIDEO_IN AUDIO_GND AUDIO_L_IN XHP_SENS AUDIO_R_IN HP_GND HP_R XCHARGE_LED HP_L SIRCS_SIG XPOWER_LED REG_GND
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
ACC_CONT REG_GND REG_GND IC3701_Y_OUT IC3701_C_OUT REG_GND
G
FP-404
FLEXIBLE
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 60 REG_GND
TO F/H (2/2)
1
2
3
4
5
6
7
8
REG_GND TD_2-3 TDO
9
XCS_IC361
REG_GND
CN940 60P
DATA_TO_SFD2
XCS_IC701
DATA_FROM_SFD2
XVSP_SCK
SFD_LRCK
IC361_ON
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
VFIO_C7
VFIO_C6
VFIO_C5
VFIO_C4
VSP_SO
VFO_HD
VFO_VD
VFO_OE
VFO_Y7
VFO_Y6
VFO_Y5
VFO_Y4
VFO_Y3
VFO_Y2
VFO_Y1
REG_GND
REG_GND
CN403 10P
XCHARGE_LED
XCHARGE_LED
XPOWER_LED
XPOWER_LED
A_4.6V
GND
GND
I
XSIRCS_SIG
J1702
EVER_3.0V
EVER_3.0V
VC-275 BOARD(1/2)
1/13 2/13 3/13 4/13 5/13 6/13 7/13 RF BLOCK JC-1 BLOCK JC-2 BLOCK IO BLOCK USB BLOCK MC BLOCK MD BLOCK 8/13 9/13 10/13 11/13 12/13 13/13 HI BLOCK AU BLOCK JK BLOCK FU BLOCK DD BLOCK CN BLOCK
(HEADPHONES)
10
1
2
3
4
5
6
7
8
9
J1701 B TO B AUDIO/VIDEO INPUT
FK-81 BOARD
CN927 10P D_2.8V XACCESS_LED XMPEG REG_GND XPHOTO_FREEZE 1 2 3 4 5 6 7 8 9 10 10 9 D_2.8V XACCESS_LED XMPEG REG_GND XPHOTO_FREEZE KEY_AD0 KEY_AD1 KEY_AD2 REG_GND REG_GND D301 (MS ACCESS) STOP FRAME + /PLAY /REC /FF /REW /PAUSE / CN301 10P S301-321,323
XCHARGE_LED
XCHARGE_LED
XPOWER_LED
XPOWER_LED
XSIRCS_SIG
EVER_3.0V
EVER_3.0V
A_4.6V
GND
GND
J
CN501 10P
10
1
2
3
4
5
6
7
8
9
FFC-322
FLAT CABLE
8 7 6 5 4 3 2 1
/MENU/PB ZOOM/VOLUM +,-/ DELETE/ /MPEG/
CN929 CN1105 4P NTPB TPB DV IN/OUT NTPA 3 4 TPA 4 5 NTPB TPB 1 2 2 3 TPA NTPA 1 GND
5P
KEY_AD0 KEY_AD1 KEY_AD2 REG_GND REG_GND
INDEX/MEMORY +,-/MEMORY PLAY/MPEG SLOW /FRAME /DISPLAY S322 PHOTO
K
PR-41 BOARD FP-602
D505 POWER ON/CHARGE IC502
FLEXIBLE
L
CN926 4P BT001 VANADIUM/ LITHIUM BATTERY CN938 1 2 3 4 LI_3V XEJECT_SW LI_3V REG_GND GND GND 1 1 2 2P
EJ-35 BOARD PL-53
HARNESS
2 XEJECT_SW REG_GND EJECT CN101 2P S101
M
16
FP-571
FLEXIBLE
TMS
SSS
N.C.
N.C.
N.C.
N.C.
TCK
TDI
REG_GND
REG_GND
4-1
4-2
FRAME SCHEMATIC DIAGRAM (1/2)
VFO_Y0
VSP_SI
VFI_HD
VFI_VD
TD_1-2
VFI_OE
VFI_C3
VFI_C2
VFI_C1
VFI_C0
VFI_Y7
VFI_Y6
VFI_Y5
VFI_Y4
VFI_Y3
VFI_Y2
VFI_Y1
VFI_Y0
A_4.6V
REG_GND
SFD_BCK
IFI_VD
XSWE
SPCK
AFCK
H
REG_GND
60
1
2
3
4
5
6
7
8
9
REG_GND
SFD_BCK
VFIO_C7
VFIO_C6
VFIO_C5
VFIO_C4
VSP_SO
VFO_HD
VFO_VD
VFO_OE
VFO_Y7
VFO_Y6
VFO_Y5
VFO_Y4
VFO_Y3
VFO_Y2
VFO_Y1
VFO_Y0
VSP_SI
VFI_HD
VFI_VD
TD_1-2
VFI_OE
VFI_C3
VFI_C2
VFI_C1
VFI_C0
VFI_Y7
VFI_Y6
VFI_Y5
VFI_Y4
VFI_Y3
VFI_Y2
VFI_Y1
VFI_Y0
IFI_VD
XSWE
SPCK
AFCK
TMS
SSS
N.C.
N.C.
N.C.
N.C.
TCK
TDI
GV-D1000/D1000E
COVER
FRAME SCHEMATIC DIAGRAM (2/2)
1 2 3 4
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
5
6
7
8
ND901 BACK LIGHT LCD 901
9
10
11
12
13
14
15
16
17
18
A
4 INCH COLOR LCD UNIT
CN5604 10P
LED_GND
BL_LOW
BL_HIGH
B LS-56 BOARD
CN001 2P AD_6 1 2 GND
CN5501 24P
VGLAC
VSH3V 23
PL-53
HARNESS
1 2 AD_6 GND
10
11
12
13
14
15
16
17
18
19
20
21
22
10
24
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
9
VSH5V
VCOM
PSS1
PSS2
MO1
MO2
GND
GND
VGH
PSG
SPD
SPS
VGL
RES
CTR
CLD
LED
N.C
N.C
N.C
N.C
N.C
N.C
CLS
EX1
EX2
VR
VG
VB
CN5502 10P CN5608 2P S5601 BRIGHT+ LCD CN5506 2P S5602 BRIGHTVB XVD_OUT 1 2 3 4 5 6 7 8 9 10 CPC (FOR CHECK)
C
S001 (LCD ON/OFF)
PD-130 BOARD
1/2 RGB,TG BLOCK 2/2 BL BLOCK
CN5607 2P
VG PANEL_COM VR SHARP/CASIO C-SYNC/XHD
SP901 SPEAKER L
1 2
SP_L_(+) SP_L_(-)
26P
XHD_OUT GND GND
CN5505 2P SP902 SPEAKER R 1 2 SP_R_(+) SP_R_(-)
CN5503
PANEL_-15.3V
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
BL_CONT
PANEL_G
PANEL_R
REG_GND
XVC_SCK
PANEL_B
BL_LOW
BL_HIGH
SP_R_+
SP_L_+
SP_R_-
AD_6
SP_L_-
VC_SO
D
PANEL_HOLD
XCS_LCD_DA
PANEL_13.3V
PANEL_4.75V
C-SYNC/XHD
PANEL_2.8V
PANEL_XVD
26
25
24
22
21
20
19
18
17
16
13
12
11
10
23
15
14
EX-39 BOARD FP-51
HARNESS
CN202 2P 2 1 BL_LOW BL_HIGT
9
8
7
6
5
4
3
2
1
1 29 30 31 NC NC NC NC 32
FP-569 E
10 11 12 13 14 15 16 17 1 2 3 4 5 6 7 8 SP_R_9 SP_R_+ REG_GND REG_GND REG_GND REG_GND VC_SO REG_GND BL_CONT XVC_SCK PANEL_-15.3V PANEL_13.3V PANEL_4.75V XCS_LCD_DA C-SYNC/XHD PANEL_2.8V PANEL_XVD
FLEXIBLE
18 19 20 21 22 23 24 25 26 27 28
NC
REG_GND
AD_6
REG_GND
SP_L_+
PANEL_-HOLD
PANEL_B
PANEL_G
PANEL_R
SP_L_-
NC
2
CN931 40P VIDEO_GND V/Y_IN V/Y_IN_GND AUDIO_R_IN AUDIO_R_IN_GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 2 3 4 5 6 7 8 9 10 11 12 VIDEO_GND V/Y_IN V/Y_IN_GND AUDIO_R_IN
CN201 40P
F VC-275 BOARD(2/2)
S1101
CN923 32P
TO F/H(1/2)
AUDIO_R_IN_GND AUDIO_L_IN AUDIO_L_IN_GND LANC_SIG LANC_GND ID1 ID2 VIDEO_GND VIDEO_OUT VIDEO_OUT_GND AUDIO_R_OUT AUDIO_R_OUT_GND AUDIO_L_OUT AUDIO_L_OUT_GND C_IN VIDEO_GND IO_GND IO_GND EX_UNREG EX_UNREG EX_UNREG EX_UNREG REG_GND REG_GND REG_GND REG_GND BL_GND BL_GND BL_GND BL_REG BL_REG BL_REG REG_GND REG_GND BEEP BEEP CN203 20P VIDEO_OUT VIDEO_OUT_GND V/Y_IN VIDEO_IN_GND AUDIO_R_IN AUDIO_L_IN AUDIO_IN_GND LANC_SIG IO_GND LANC_GND ID1 EX_GND EX_GND AUDIO_R_OUT AUDIO_L_OUT AUDIO_OUT_GND ID2 EX_UNREG EX_UNREG C_IN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MULTI CONNECTOR
CN933 1 2 3 4 5
20P
AUDIO_L_IN AUDIO_L_IN_GND LANC_SIG LANC_GND ID1 ID2 VIDEO_GND VIDEO_OUT VIDEO_OUT_GND AUDIO_R_OUT CPC (FOR CHECK) AUDIO_R_OUT_GND AUDIO_L_OUT AUDIO_L_OUT_GND C_IN VIDEO_GND IO_GND IO_GND EX_UNREG EX_UNREG EX_UNREG EX_UNREG REG_GND REG_GND REG_GND REG_GND
LANC_SIG N.C. EVF_LED_DA EVF_VG EVF_VGO GND PANEL_VG PD_VCO H_START XHD/PSIG PANEL_COM TMS TCK JIG_TDI JIG_TDO GND SWP RF_IN/LANC_JACK_IN GND RF_MON
G
RESET 6 7 8 9 10 S1701 D1711 VCR (SIRCS MITTER) 11 12 13 14 VCR CN1701 5P 1 2 (USB) 3 4 5 VCC DD+ ID GND (MEMORY STICK) 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
FP-570
FLEXIBLE
13 14 15 16 17 18 19 20
H
I
SW_COM/SW_GND MIC/REC_SW_GND XCCDOWN_SW TOP/END_GND
BL_GND
XREC_PROOF
27P
MODE_SW_A
MODE_SW_B
MODE_SW_C
10P
LM_UNLOAD
LM_UNLOAD
BL_GND
TAPE_LED_K
TAPE_LED_A
CN934 10P
CHIME_VDD
CHIME_SDA
CHIME_SCK
PG/FG COM
HALL_GND
27P
HALL_VCC
TAPE_END
DRUM_W
TAPE_TOP
LM_LOAD
DRUM_W
DRUM_U
DRUM_U
DRUM_V
DRUM_V
LM_LOAD
BL_GND
HE_GND
FG_GND
CN3101
FG_GND
HE_VCC
FG_VCC
FG_VCC
SREEL+
TREEL+
CAP_W
CAP_W
CAP_W
CAP_W
SREEL-
M COM
TREEL-
CAP_U
CAP_U
CAP_U
CAP_U
CAP_V
CAP_V
CAP_V
CAP_V
YEVEN
XEVEN
CN936
CN937
DEW+
WHE+
YODD
XODD
WHE-
DEW-
YSDL
XSDL
UHE+
VHE+
UHE-
VHE-
BL_REG BL_REG BL_REG REG_GND REG_GND BEEP BEEP
GND
GND
GND
GND
N.C.
FG1
J
10
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
FG2
PG
FG
26 26 FG_GND
10
10
10
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
26
25
24
23
22
21
20
19
18
17
16
15