Text preview for : SONY GV-D200, D200E, D800, D800E SERVICE MANUAL VER 1.2 2003.06 (9-929-853-13).pdf part of SONY GV-D800 SONY GV-D200, D200E, D800, D800E.
DIGITAL VIDEO CASSETTE RECORDER.
SERVICE MANUAL VERSION 1.2 2003.06
PART#(9-929-853-13)
Back to : SONY GV-D200, D200E, D800 | Home
GV-D200/D200E/D800/D800E
SERVICE MANUAL
Ver 1.2 2003. 06
US Model Canadian Model
GV-D200/D800
AEP Model UK Model E Model
GV-D200E/D800E
Photo : GV-D800E
B MECHANISM
NTSC MODEL : GV-D200/D800 PAL MODEL : GV-D200E/D800E Function difference table Model GV-D200/200E GV-D800/D800E Function LCD -- 4.0 inches
For MECHANISM ADJUSTMENT, refer to the "8mm Video MECHANICAL ADJUSTMENT MANUAL " (9-973-801-11).
SPECIFICATIONS
VCR
System Video recording system 2 rotary heads Helical scanning system Audio recording system Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs 48 kHz, stereo) Video signal GV-D200/D800: NTSC color, EIA standards GV-D200E/D800E: PAL colour, CCIR standards Recommended cassette Hi8 /Digital8 video cassette Recording/playback time (GV-D200/D800: using 120 min. Hi8 video cassette) (GV-D200E/D800E: using 90 min. Hi8 (PAL) video cassette) SP mode: 1 hour LP mode: 1 hour and 30 minutes Fastforward/rewind time (GV-D200/D800: using 120 min. Hi8 video cassette) (GV-D200E/D800E: using 90 min. Hi8 (PAL) video cassette) Approx. 5 minutes and 15 seconds Input/output connectors S video input 4-pin mini DIN Luminance signal: 1 Vp-p, 75 ohms, unbalanced GV-D200/D800: Chrominance signal: 0.286 Vp-p GV-D200E/D800E: Chrominance signal: 0.3 Vp-p, 75 ohms, unbalanced S video output 4-pin mini DIN Luminance signal: 1 Vp-p, 75 ohms, unbalanced GV-D200/D800: Chrominance signal: 0.286 Vp-p GV-D200E/D800E: Chrominance signal: 0.3 Vp-p, 75 ohms, unbalanced Audio/Video input AV MINIJACK Video: 1 Vp-p, 75 ohms, unbalanced, sync negative Audio: 327 mV, input impedance more than 47 kiloohms Video output Phono jack, 1 Vp-p, 75 ohms, unbalanced, sync negative Audio output Phono jacks (2) 327 mV, output impedance less than 1 kiloohm RFU DC OUT Special minijack DC 5 V DV input/output 4-pin connector Headphone jack Stereo minijack (ø 3.5 mm) jack LANC Stereo mini-minijack (ø 2.5 mm) LCD screen (GV-D800/D800E) Picture 4.0 type 80.6 × 60.5 mm (3 1/4 × 2 1/2 in.) Total dot number 123,200 (560 × 220) General Power requirements 7.2 V (battery pack) 8.4 V (AC power adaptor) Average power consumption (when using the battery pack) GV-D800/D800E only During playback using LCD 4.9 W During playing back when you close the LCD panel 3.0 W Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F) Dimensions (Approx.) GV-D200/D200E: 148 × 50 × 135 mm (5 7/8 × 2 × 5 3/8 in.) GV-D800/D800E: 148 × 65 × 135 mm (5 7/8 × 2 5/8 × 5 3/8 in.) (w/h/d) Mass (approx.) GV-D200/D200E: 660 g (1 lb 7 oz) GV-D800/D800E: 930 g (2 lb) excluding the battery pack and cassette Supplied accessories See page 2.
AC power adaptor
Power requirements 100 - 240 V AC, 50/60 Hz Power consumption 23 W Output voltage DC OUT: 8.4 V, 1.5 A in the operating mode Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F)
-- Continued on next page --
DIGITAL VIDEO CASSETTE RECORDER
Dimensions (approx.) 125 × 39 × 62 mm (5 × 1 9/16 × 2 1/2 in.) (w/h/d) excluding projecting parts Mass (approx.) 280 g (9.8 oz) excluding power cord Cord length (approx.) Power cord: 2 m (6.6 feet) Connecting cord: 1.6 m (5.2 feet) Design and specifications are subject to change without notice.
· SUPPLIED ACCESSORIES
Make sure that the following accessories are supplied with your VCR.
1 2
3
4
1 AC-L10A/L10B/L10C AC power adaptor (1), Mains lead (1) 2 A/V converting cable (1)
3 A/V connecting cable (1) 4 21-pin adaptor (1) GV-D200E/D800E only
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering.
2. 3.
--2--
TABLE OF CONTENTS SERVICE NOTE
1. 2. 3. POWER SUPPLY DURING REPAIRS ····························· 6 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) (1) ·························································· 6 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) (2) (TO TAKE OUT A CASSETTE WITHOUT HURTING THE TAPE) ······················································ 7 2-4. PD-130, LS-56 BOARDS (D800, D800E MODEL) ······ 2-4 2-5. LCD WINDOW CABINET ASSEMBLY (SP-901, 902) (D800, D800E MODEL) ················································· 2-5 2-6. BATTERY PANEL ASSEMBLY, BATTERY TERMINAL BOARD, DC-IN CONNECTOR ····································· 2-6 2-7. VC-250, FU-145 BOARDS ············································· 2-6 2-8. CONTROL SWITCH BLOCK (FK-78), LOADING LID ·· 2-7 2-9. MECHANISM DECK, MAIN FRAME ASSEMBLY ··· 2-7 2-10. CABINET (R) BLOCK ASSEMBLY, JACK FRAME (IO-68, IR-38 BOARDS) ················································ 2-8 2-11. EX-36 BOARD, FP-570 FLEXIBLE BOARD ··············· 2-9 2-12. UPPER CABINET ASSEMBLY, LCD BLOCK ASSEMBLY (D800, D800E MODEL) ···· 2-9 2-13. HINGE UNIT, FP-569 FLEXIBLE BOARD (D800, D800E MODEL) ··············································· 2-10 2-14. CIRCUIT BOARDS LOCATION ································· 2-12 2-15. FLEXIBLE BOARDS LOCATION ······························ 2-13
SELF-DIAGNOSIS FUNCTION
1. 2. 3. 3-1. 3-2. 3-3. 4. SELF-DIAGNOSIS FUNCTION ······································· 8 SELF-DIAGNOSIS DISPLAY ·········································· 8 SERVICE MODE DISPLAY ············································· 8 Display Method ·································································· 8 Switching of Backup No. ··················································· 8 End of Display ···································································· 8 SELF-DIAGNOSIS CODE TABLE ··································· 9
1.
GENERAL
3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6.
BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/4) ··························· 3-1 OVERALL BLOCK DIAGRAM (2/4) ··························· 3-3 OVERALL BLOCK DIAGRAM (3/4) ··························· 3-5 OVERALL BLOCK DIAGRAM (4/4) ··························· 3-7 POWER BLOCK DIAGRAM (1/2) ································ 3-9 POWER BLOCK DIAGRAM (2/2) ······························ 3-11
Getting started Using this manual ·································································· 1-1 Checking supplied accessories ·············································· 1-1 Step 1 Preparing the power supply ········································ 1-1 Connecting to the mains ····················································· 1-1 Using with a battery pack (not supplied) ···························· 1-2 Step 2 Inserting a cassette ····················································· 1-2 Basic operations Playing back a tape ······························································· 1-3 Viewing the recording on TV ················································ 1-4 Recording from the other VCR or TV ··································· 1-5 Advanced operations Enlarging playback images PB ZOOM ······························ 1-6 Watching a tape with special effects Picture effect ············· 1-7 Watching a tape with special performances Digital effect ·· 1-7 Quickly locating a scene Zero set memory ························· 1-8 Searching with recording date Date search ························ 1-8 Searching for a photo Photo search/Photo scan ·················· 1-9 Displaying recording data and screen indicators Data code function ······························································ 1-9 Superimposing a title ··························································· 1-10 Making your own titles ························································ 1-10 Editing Dubbing a tape ····································································· 1-11 Dubbing only desired scenes Digital program editing ····· 1-12 Using with an analogue video unit and a personal computer Signal convert function ····················································· 1-15 Inserting a scene from the other (playback) VCR Insert Editing ···································································· 1-15 Customizing your VCR Changing the menu settings ················································· 1-16 Resetting the date and time ·················································· 1-17 Additional information Digital8 system, recording, and playback ······················· 1-18 About i.LINK ······································································· 1-19 Troubleshooting ··································································· 1-19 Self-diagnosis display ·························································· 1-20 Warning indicators and messages ········································ 1-20 Using your VCR abroad ······················································ 1-21 Maintenance information and precautions ··························· 1-21 Quick reference Identifying the parts and controls ········································ 1-22
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
2.
DISASSEMBLY
2-1. CASSETTE LID ASSEMBLY ········································ 2-2 2-2. BOTTOM CABINET ASSEMBLY, FP-571 FLEXIBLE BOARD (LITHIUM BATTERY) ···································· 2-2 2-3. LCD CABINET ASSEMBLY (D800, D800E MODEL) ·· 2-3
4-1. FRAME SCHEMATIC DIAGRAM (1/2) ······················· 4-1 FRAME SCHEMATIC DIAGRAM (2/2) ······················· 4-3 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS ············································ 4-5 · VC-250 (REC/PB AMP, DAC, DV INTERFACE, AD CONVERTER, Y/C PROCESSOR, LINE A/D, LINE I/O, IR, AUDIO I/O, DRUM/CAPSTAN MOTOR DRIVE, MECHA CONTROL, HI CONTROL, DC/DC CONVERTER, CONNECTION) PRINTED WIRING BOARD ························· 4-7 · VC-250 (REC/PB AMP)(1/16) SCHEMATIC DIAGRAM ···························· 4-11 · VC-250 (PB AMP, DAC)(2/16) SCHEMATIC DIAGRAM ···························· 4-13 · VC-250 (DV INTERFACE)(3/16) SCHEMATIC DIAGRAM ···························· 4-15 · VC-250 (DV INTERFACE)(4/16) SCHEMATIC DIAGRAM ···························· 4-17 · VC-250 (AD CONVERTER)(5/16) SCHEMATIC DIAGRAM ···························· 4-19 · VC-250 (Y/C PROCESSOR)(6/16) SCHEMATIC DIAGRAM ···························· 4-21 · VC-250 (LINE A/D)(7/16) SCHEMATIC DIAGRAM ···························· 4-23 · VC-250 (LINE IN/OUT)(8/16) SCHEMATIC DIAGRAM ···························· 4-25 · VC-250 (IR)(9/16) SCHEMATIC DIAGRAM ···························· 4-27 · VC-250 (MECHANISM CONTROL)(10/16) SCHEMATIC DIAGRAM ···························· 4-29 · VC-250 (AUDIO I/O)(11/16) SCHEMATIC DIAGRAM ···························· 4-31 · VC-250 (DRUM/CAPSTAN MOTOR DRIVE)(12/16) SCHEMATIC DIAGRAM ···························· 4-33 · VC-250 (MECHA CONTROL)(13/16) SCHEMATIC DIAGRAM ···························· 4-35 · VC-250 (HI CONTROL)(14/16) SCHEMATIC DIAGRAM ···························· 4-37
--3--
· VC-250 (DC/DC CONVERTER)(15/16) SCHEMATIC DIAGRAM ···························· 4-39 · VC-250 (CONNECTION)(16/16) SCHEMATIC DIAGRAM ···························· 4-41 · FP-575 (LANC), IO-68 (AV IN/OUT) PRINTED WIRING BOARDS ····················· 4-43 · IO-68 (AV IN/OUT) SCHEMATIC DIAGRAM ···························· 4-45 · FU-145 (DC/DC CONVERTER) PRINTED WIRING BOARD ······················· 4-47 · FU-145 (DC/DC CONVERTER) SCHEMATIC DIAGRAM ···························· 4-49 · PD-130 (LCD DRIVER, BACK-LIGHT) PRINTED WIRING BOARD ······················· 4-51 · LS-56 (LCD SWITCH) PRINTED WIRING BOARD ······················· 4-54 · PD-130 (LCD DRIVER, BACK-LIGHT)(1/2) SCHEMATIC DIAGRAM ···························· 4-55 · PD-130 (BACK-LIGHT)(2/2) SCHEMATIC DIAGRAM ···························· 4-57 · IR-38 (IR TRANSMITTER), CONTROL SWITCH BLOCK (FK-78) PRINTED WIRING BOARDS ····················· 4-59 · CONTROL SWITCH BLOCK (FK-78) SCHEMATIC DIAGRAM ···························· 4-61 · EX-36 (MULTI CONNECTOR) PRINTED WIRING BOARD ······················· 4-63 · EX-36 (MULTI CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-65 · FP-571 (BATTERY), FP-249 (S/T REEL) PRINTED WIRING BOARDS ····················· 4-67 4-3. WAVEFORMS ······························································ 4-68 4-4. MOUNTED PARTS LOCATION ································· 4-70
5.
ADJUSTMENTS
1. Before starting adjustment ··············································· 5-1 1-1. Adjusting items when replacing main parts and boards. · 5-2 5-1. ADJUSTMENT PREPARATIONS ································· 5-3 1-1. PREPARATIONS BEFORE ADJUSTMENT ················· 5-3 1-1-1. List of Service Tools ························································ 5-3 5-2. MECHANISM SECTION ADJUSTMENT ···················· 5-4 2-1. Hi8/STANDARD8 MODE ·············································· 5-4 2-1-1. OPERATING WITHOUT CASSETTE ·························· 5-4 2-1-2. TAPE PATH ADJUSTMENT ·········································· 5-4 1. Preparations for Adjustment ············································ 5-4 2-2. DIGITAL8 MODE ·························································· 5-5 2-2-1. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ····································································· 5-5 2-2-2. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ····································································· 5-5 2-2-3. OVERALL TAPE PATH CHECK ··································· 5-5 1. Recording of the tape path check signal ·························· 5-5 2. Tape path check ······························································· 5-5 5-3. ELECTRICAL ADJUSTMENT ······································ 5-6 3-1. PREPARATIONS BEFORE ADJUSTMENTS ·············· 5-6 3-1-1. Equipment to Required ···················································· 5-6 3-1-2. Precautions on Adjusting ················································· 5-7 3-1-3. Adjusting Connectors ······················································ 5-7 3-1-4. Connecting the Equipment ·············································· 5-8 3-1-5. Alignment Tape ······························································· 5-9 3-1-6. Input/output Level and Impedance ································ 5-10 3-2. INITIALIZATION OF C, D, E, F, 7, 8 PAGE DATA ··· 5-11 3-2-1. INITIALIZATION OF C, D, 8 PAGE DATA ················ 5-11 1. Initializing the C, D, 8 Page Data ·································· 5-11 2. Modification of C, D, 8 Page Data ································ 5-11 3. C Page Table ·································································· 5-11 4. D Page Table ·································································· 5-12
5. 8 Page Table ··································································· 5-13 3-2-2. INITIALIZATION OF E, F, 7 PAGE DATA ················· 5-14 1. Initializing the E, F, 7 Page Data ··································· 5-14 2. Modification of E, F, 7 Page Data ································· 5-14 3. F Page Table ·································································· 5-14 4. E Page Table ·································································· 5-15 5. 7 Page Table ··································································· 5-16 3-3. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-17 1. Serial No. Input ····························································· 5-17 1-1. Company ID Input ························································· 5-17 1-2. Serial No. Input ····························································· 5-17 2. Battery End Adjustment ················································ 5-19 3-4. SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-20 1. REEL FG Adjustment (VC-250 Board) ························ 5-20 2. PLL fo & LPF fo Pre-Adjustment (VC-250 Board) ······ 5-20 3. Switching Position Adjustment (VC-250 Board) ·········· 5-21 4. AGC Center Level and APC & AEQ Adjustment ········· 5-21 4-1. Preparations before adjustments ···································· 5-21 4-2. AGC Center Level Adjustment (VC-250 Board) ·········· 5-21 4-3. APC & AEQ Adjustment (VC-250 Board) ··················· 5-22 4-4. Processing after Completing Adjustments ···················· 5-22 5. PLL fo & LPF fo Final Adjustment (VC-250 Board) ··· 5-23 6. Hi8/Standard8 Switching Position Adjustment (VC-250 Board) ····························································· 5-23 7. CAP FG Offset Adjustment (VC-250 board) ················ 5-24 3-5. VIDEO SYSTEM ADJUSTMENTS ····························· 5-25 27MHz Origin Oscillation Adjustment (VC-250 board) ·· 5-25 1. 2. Chroma BPF fo Adjustment (VC-250 Board) ··············· 5-25 3. S VIDEO OUT Y Level Adjustment (VC-250 Board) ·· 5-26 4. S VIDEO OUT Chroma Level Adjustment (VC-250 Board) ····························································· 5-26 5. VIDEO OUT Y, Chroma Level Check (VC-250 Board) ·· 5-27 Hi8/Standard8 Y/C Output Level Setting (VC-250 Board) · 5-27 6. 7. Hi8/standard 8mm AFC fo Adjustment (VC-250 board) ·· 5-28 3-6. IR TRANSMITTER ADJUSTMENTS ························· 5-29 1. IR Video Carrier Frequency Adjustment (VC-250 board) ·· 5-29 2. IR Video Deviation Adjustment (VC-250 board) ·········· 5-29 3. IR Audio Deviation Adjustment (VC-250 board) ········· 5-30 3-7. AUDIO SYSTEM ADJUSTMENTS ···························· 5-31 1. Hi8/Standard8 AFM BPF fo Adjustment (VC-250 board) ·· 5-31 2. Hi8/Standard8 AFM 1.5 MHz Deviation Adjustment (VC-250 board) ····························································· 5-32 3. Hi8/Standard8 AFM 1.7 MHz Deviation Adjustment (VC-250 board) ····························································· 5-32 4. Digital8 Playback Level Check ····································· 5-32 5. Overall Level Characteristics Check ····························· 5-32 6. Overall Distortion Check ··············································· 5-32 7. Overall Noise Level Check ············································ 5-33 8. Overall Separation Check ·············································· 5-33 3-8. LCD SYSTEM ADJUSTMENT (GV-D800/D800E) ··· 5-34 1. LCD Initial Data Input (1) ············································· 5-34 2. LCD Initial Data Input (2) ············································· 5-35 3. VCO Adjustment (PD-130 board) ································· 5-35 4. RGB AMP Adjustment (PD-130 board) ························ 5-36 5. Contrast Adjustment (PD-130 board) ···························· 5-36 6. COM AMP Adjustment (PD-130 board) ······················· 5-37 7. V-COM Adjustment (PD-130 board) ···························· 5-37 8. White Balance Adjustment (PD-130 board) ·················· 5-38 5-4. SERVICE MODE ·························································· 5-39 4-1. ADJUSTMENT REMOTE COMMANDER ················ 5-39 1. Using the Adjustment Remote Commander ·················· 5-39 2. Precautions Upon Using the Adjustment Remote Commander ··································································· 5-39 4-2. DATA PROCESS ··························································· 5-40 4-3. SERVICE MODE ·························································· 5-41 1. Setting the Test Mode ···················································· 5-41 2. Emergence Memory Address ········································ 5-41
--4--
2-1. 2-2. 2-3. 2-4. 3. 4. 5. 6. 7. 8. 9.
C Page Emergence Memory Address ···························· 5-41 F Page Emergence Memory Address ···························· 5-42 EMG Code (Emergency Code) ····································· 5-42 MSW Code ···································································· 5-43 Bit Value Discrimination ··············································· 5-44 Switch check (1) ···························································· 5-44 Switch check (2) ···························································· 5-44 Switch check (3) ···························································· 5-44 Switch check (4) ···························································· 5-45 Record of Use check ······················································ 5-45 Record of Self-diagnosis check ····································· 5-46
6.
REPAIR PARTS LIST
6-1. EXPLODED VIEWS ······················································ 6-1 6-1-1. OVERALL SECTION-1 ················································· 6-1 6-1-2. OVERALL SECTION-2 ················································· 6-2 6-1-3. LCD SECTION (D800/D800E MODEL) ······················· 6-3 6-1-4. MECHANISM SECTION ··············································· 6-4 6-1-5. CASSETTE COMPARTMENT ASSEMBLY ················ 6-5 6-1-6. LS CHASSIS ASSEMBLY ············································· 6-6 6-1-7. MECHANISM CHASSIS ASSEMBLY ························· 6-7 6-2. ELECTRICAL PARTS LIST ·········································· 6-8
--5--
SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power code (J-6082-223-A), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1: Connect the adjustment remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the HOLD switch to the "ADJ" side. Method 2: Use the DC IN terminal. (Use the AC power adaptor. (AC-L10, AC-VQ800 etc.))
2.
1 2 3 4 5
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) (1)
Remove the power supply (Battery or AC power adaptor). Push the EJECT switch and open the cassette lid. Refer to 2-2. to remove the cabinet (lid) assembly. Refer to 2-2. to remove the cabinet (bottom) assembly. Add 5V from the regulated power supply between Pin 5, 6 of CN4401 (ULD5V +) and Pin 7, 8 of CN4401 (ULD5V ), and unload the cassette.
CN4401 8 ULD 5V 1
VC-250 board
Regulated power supply (+5V)
--6--
3.
1 2 3 4 5 6 7 8
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) (2) (TO TAKE OUT A CASSETTE WITHOUT HURTING THE TAPE)
Disconnect the power supply (Battery or AC adaptor) Refer to 2-2. to remove the cabinet (lid) assembly. Refer to 2-2. to remove the cabinet (bottom) assembly. Refer to 2-1. to remove the Cassette (lid) assembly. Refer to 2-6 to 2-8. to remove the LCD block (GV-D800/D800E only) and the cabinet (upper) assembly. Remove the FU-145 board. Refer to 2-9. to remove the lid frame assembly. Add +5V from the regulated power supply and unload with a pressing the cassette lid.
9 Pull the timing belt in the direction of arrow A with a pincette while pressing the cassette lid (take care not to damage) to adjust the bending of a tape.
Press the cassette lid not to rise the cassette compartment
Pincette Regulated power supply (+5V)
Timing belt
0 Let go your hold the cassette lid and rise the cassette compartment to take out a cassette.
Loading motor
Timing belt
Adjust the bending of a tape
--7--
SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTION 2. SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the LCD screen or monitor TV (Note) what to do. This function consists of two display; selfdiagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
LCD screen or monitor TV
C:31:11
When problems occur while the unit is operating, the counter of the viewfinder shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
Note: Set the DISPLAY in the menu system to V-OUT/LCD only for the model with LCD screen, and press the DISPLAY button.
Blinks at 3.2Hz
C
Repaired by:
31
Block
11
Detailed Code
C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
Refer to page 9. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
3.
3-1.
SERVICE MODE DISPLAY
Display Method
The service mode display shows up to six self-diagnosis codes shown in the past.
While pressing the "STOP" key, set the POWER switch from OFF to ON, and continue pressing the "STOP" key for 10 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
LCD screen or monitor TV
[3] C : 3 1 : 1 1
Lights up
[3]
Backup No. Order of previous errors
C:31:11
Control dial self-diagnosis codes
3-2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time
3-3.
End of Display
Turning OFF the power supply will end the service mode display.
Note: The "self-diagnosis display" data will be backed up by the coin-type lithium battery of FP-571 flexible board. When this coin-type lithium battery is removed, the "self-diagnosis display" data will be lost by initialization.
--8--
4.
Repaired by:
SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code Block Detailed Function Code 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4 0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2 Symptom/State Correction
C C C C C C C C C C C C C C C C C C C C C C C
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning.
--9--
SECTION 1 GENERAL
GV-D200/D200E/D800/D800E
This section is extracted from instruction manual. (GV-D800E model)
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23E
SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. Cassette Lid assembly
GV-D200/D200E/D800/D800E
2-2. Bottom cabinet assembly, FP-571 flexible board (Lithium battery) PD-130 board service position (D800, D800E model)
2-3. LCD cabinet assembly (D800, D800E model)
GV-D200/D200E/D800/D800E
2-6. Battery panel assembly, Battery terminal board, DC-IN connector
2-4. PD-130, LS-56 boards (D800, D800E model)
2-7. VC-250, FU-145 boards
2-5. LCD window cabinet assembly (SP-901,902) (D800, D800E model)
2-9. Mechanism deck, Main frame assembly
2-8. Control switch block (FK-78), Loading lid
2-10. Cabinet (R) block assembly, Jack frame (IO-68, IR-38 boards)
2-11. EX-36 board, FP-570 flexible board
2-12. Upper cabinet assembly, LCD block assembly (D800, D800E model) 2-13. Hinge unit , FP-569 flexible board (D800, D800E model)
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)] (VC-250, FU-145, IO-68 boards, Mechanism deck)
2-1
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. CASSETTE LID ASSEMBLY
2 Two screws (M2 × 4), lock ace, p2 6 Cassette lid assembly 1 Open the LCD panel in the direction of the arrow A. (GV-D800/D800E model)
Push
5 Claw
4 Three dowels
A
3 Press the cassette EJECT knob to open the cassette compartment.
2-2. BOTTOM CABINET ASSEMBLY, FP-571 FLEXIBLE BOARD (LITHIUM BATTERY)
7 Bottom cabinet assembly 3 Three screws (M2 × 4), lock ace, p2 4 Two screws (M2 × 4), lock ace, p2 6 Open the jack lid assembly in the direction of the arrow B. B 2 Press the release button to remove the cabinet lid assembly in the direction of the arrow A. 5 Screw (M2 × 4), lock ace, p2
A 0 FP-571 flexible board (4P)
50 Bo ar d
8 Tapping screw (+k 2 ×5)
C
1 Open the LCD panel little. (GV-D800/D800E model) 9 Remove the lithium lid in the direction of the arrow C.
2-2
VC
-2
2-3. LCD CABINET ASSEMBLY (D800, D800E MODEL)
2 Two screws (M2 × 4), lock ace, p2 6 Remove the LCD cabinet assembly in the direction of the arrow.
3 Two screws (M2 × 3), lock ace, p2 1 Two screws (M2 × 4), lock ace, p2 4 Two claws 5 Two claws
[PD-130 BOARD SERVICE POSITION] (D800, D800E MODEL)
Multi-CPC jig (J-6082-311-A)
Touching here is safe when the machine is normal. However touching here can be dangerous if defective parts exist. LANC jack
CN5607
Caution High voltage
0 3 -1 d D r P oa B
Adjustment remote commander (RM-95)
1 2 10 9
PD-130 board AC POWER ADAPTOR
AC IN
CN5502 LS-56 board CN01 (2P)
When the hinge unit is closed to be laid down, remove CN01 (2P) on the LS-56 board. If not, the main power cannot be turned on.
2-3
2-4. PD-130, LS-56 BOARDS (D800, D800E MODEL)
9 Three screws (M2 × 3), lock ace, p2 6 Two tapping screws (B2 × 5)
P Bo D-1 ar 30 d
7 FP-569 flexible board (26, 32P) 0 Remove the PD-130 board in the direction of the arrow.
3 Harness (PL-53) (2P)
8 Harness (EP-51) (2P) qs LS-56 board, LS bracket qa Screw (M2 × 3), lock ace, p2
4 ND901 (10P) 1 SP902 (2P) 5 LCD901 (24P) 2 SP901 (2P)
2-4
2-5. LCD WINDOW CABINET ASSEMBLY (SP-901, 902)(D800, D800E MODEL)
1 Two tapping screws (B2 × 5) 2 Two tapping screws (B2 × 5)
3 PD frame 6 LCD901
5 LCD ground plate 4 Screw (M2 × 3), lock ace, p2
9 ND901
7 Two claws
8 Two claws
REMOVING THE LCD WINDOW CABINET ASSEMBLY (SP901, 902)
1 Tapping screw (B2 × 5)
5 Tapping screw (B2 × 5) 3 SP ground plate 6 SP ground plate 4 SP902 7 SP901 2 Remove the SP ground plate in the direction of the arrow. Dowel
8 LCD window cabinet assembly
Claw
2-5
2-6. BATTERY PANEL ASSEMBLY, BATTERY TERMINAL BOARD, DC-IN CONNECTOR
7 Two tapping screws (B2 × 5)
0 Mechanism section
9 DC-IN connector (3P), DC jack assembly
Bo ar d VC -2 50
6 Battery panel assembly, Battery terminal board 5 FP-247 flexible board (50P) 3 FP-569 flexible board (26, 32P) 1 FP-570 flexible board (40P)
4 FP-572 flexible board (6, 10P)
2 FP-602 flexible board (5P) 8 Two screws (M2 × 4), lock ace, p2
2-7. VC-250, FU-145 BOARDS
3 Three screws (M2 × 3), lock ace, p2 4 VC-250 board A Control switch block (FK-78) (10P) B Flexible board (from loading motor, mode switch) (8P) C Flexible board (from video head) (16P) D Flexible board (from drum motor) (10P) E Flexible board (from capstan motor) (12P) F Flexible board (from S reel/T reel) (15P) 1 Two screws (M2 × 3), lock ace, p2 2 FU-145 board
VC
-2
50
Bo ar
d
F E D C 5 Mechanism deck B A
F E D C B A
Battery panel assembly, Battery terminal board
2-6
2-8. CONTROL SWITCH BLOCK (FK-78), LOADING LID
2 Screw (M1.4 × 1.6) 1 Remove the control switch block (FK-78) (10P) in the direction of the arrow. 6 Control switch block (FK-78) (10P) 3 Screw (M1.4 × 1.6)
7 Two screws (M2 × 4), lock ace, p2
4 Dowel
5 Dowel
8 Loading lid
9 Mechanism deck
2-9. MECHANISM DECK, MAIN FRAME ASSEMBLY
1 Two screws (M2 × 3), lock ace, p2
5 Lid frame assembly
9 Mechanism deck
V Bo C-2 ar 50 d
6 Open the VC-250 board in the direction of the arrow . 3 Two dowels 8 Main frame assembly
2 Screw (M2 × 3), lock ace, p2
4 Two dowels 7 Three screws (M2 × 3), lock ace, p2
2-7
2-10. CABINET (R) BLOCK ASSEMBLY, JACK FRAME (IO-68, IR-38 BOARDS)
2 Cabinet (R) block assembly 1 Three tapping screws (B2 × 5) 3 Five tapping screws (B2 × 6)
REMOVING THE JACK FRAME
8 Screw (M2 × 3), lock ace, p2 5 FP-247 flexible board (50P)
4 Cabinet (R)
3 Screw (M2 × 3), lock ace, p2
-38 IR
4 FP-575 flexible board (6P)
9 IR-38 board, FP-572 flexible board (6, 10P)
0 Jack frame 2 FP-246 flexible board (16P)
FP
-2
46
I BoO-6 ar 8 d
1 Two screws (M2 × 3), lock ace, p2 7 IO-68 board
6 Three screws (M2 × 4), lock ace, p2
2-8
2-11.EX-36 BOARD, FP-570 FLEXIBLE BOARD
1 Three tapping screws (B2 × 5) 2 Harness (EP-51) (2P)
EX -3
6
bo
ar
d
3 EX-36 board, FP-570 flexible board (40P)
2-12.UPPER CABINET ASSEMBLY, LCD BLOCK ASSEMBLY (D800, D800E MODEL)
2 FP-602 flexible board (5P), Strap sheet metal (L) 4 Strap sheet metal (R)
5 Upper cabinet assembly
3 Two screws (M2 × 4), lock ace, p2 1 Two screws (M2 × 4), lock ace, p2
(GV-D800/D800E model)
8 Remove the LCD block assembly in the direction of the arrow A. 7 Claw
A
6 Claw D
qs Shaft cover (R)
0 Remove the shaft cover (R), shaft cover (L) in the direction of the arrow C D.
Claw
C qa Shaft cover (L)
B
9 Open the LCD block assembly in the direction of the arrow B.
2-9
2-13.HINGE UNIT, FP-569 FLEXIBLE BOARD (D800, D800E MODEL)
When attaching the hinge unit, wrap the FP-569 flexible board hinge shaft as shown while taking care so that the flexible board must not be caught or pinched. Hinge unit FP-569 flexible board (26, 32P)
3 FP-569 flexible board (26, 32P) 4 Hinge unit
Hinge shaft
1 Two tapping screws (B2 × 5)
LS-56 board
Hinge unit Harness (EP-51) (2P) Hinge shaft
0 3 -1 D rd P oa B
2 Harness (PL-53) (2P)
When attaching the hinge unit, route the harness through the notch as shown while taking care so that the harness must not be caught or pinched.
Harness (EP-51) (2P)
2-10
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)] (VC-250, FU-145, IO-68 BOARDS, MECHANISM DECK)
Control switch block (FK-78) (10P)
CPC-13 jig (J-6082-443-A) VC-250 board CN933 AC POWER ADAPTOR
V Bo C-2 ar 50 d
20 1
AC IN
DC-IN connector (3P), DC jack assembly
5 -14 FUard Bo
FP-247 flexible board (50P) Mechanism deck FU-145 board
Battery panel assembly, Battery terminal board
-68 IO ard Bo
FP-246 flexible board (16P) IO-68 board
FP-575 flexible board (6P) LANC jack
Adjustment remote commander (RM-95)
2-11
2-14.CIRCUIT BOARDS LOCATION
LCD DISPLAY MODULE (D800/D800E ONLY) PD-130 LCD DRIVER, BACK LIGHT LS-56 (LCD SWITCH) EX-36 (MULTI CONNECTOR)
FP-602 (DV IN/OUT)
IR-38 (IR TRANSMITTER)
FP-575 (LANC)
FU-145 (DC/DC CONVERTER) IO-68 (AV IN/OUT) FP-246 (REMOTE COMMANDER RECEIVER) VC-250 REC/PB AMP, DAC, DV INTERFACE, AD CONVERTER, Y/C PROCESSOR, LINE A/D, LINE IN/OUT, IR, AUDIO IN/OUT, DRUM/CAPSTAN MOTOR DRIVE, MECHA CONTROL, HI CONTROL, DC/DC CONVERTER
2-12
2-15.FLEXIBLE BOARDS LOCATION
The flexible boards contained in the mechanism deck are not shown.
CONTROL SWITCH BLOCK (FK-78) FP-570
FP-571
FP-569 FP-572
FP-247
2-13E
SECTION 3 BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/4)
(SEE PAGE 4-45)
GV-D200/D200E/D800/D800E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
IO-68 BOARD (1/2)
J101 S VIDEO IN Y C 32 31 CN103 30 29
VC-250 BOARD(1/4)
(4-25)
(4-26)
(4-23)
IC3702
CN922 11 EX Y/V IN 5 14 16 EX C IN 36 35 3 1 8 6 9 J103 S VIDEO OUT Y C 20 18 19 17 Y C 18 14 Y C V 39 48 42
IC3701
(TAKO) LINE IN LINE OUT AGC ACC Y C 36 34 2 6
IC3603
(ALIGN) A/D CONVERTER 59 Y0-Y7 52 49 C0-C7 42 38 HD,VD,DE 37 36 34 68 31 65 66 64 63 AFCK SPCK (IC1505) XCS ALIGN (IC4803) TO OVERALL BLOCK(2/4)
(SEE PAGE 3-3)
IC3703 (4-25)
EX VIDEO OUT J102 VIDEO OUT L AUDIO OUT R V L R 16 12 10 15 11 9 1 3 V 22
(4-27)
IC3901
IR TRANSMITTER 41 46 48 7 18 44 5 IR FSC (IC3301) 9 10 11 XCS TAKO (IC4501) IR V IR L IR R 24 46 7
HI SO,HI SI,XHI SCK SIRCS PWM CAIN Y CAIN C KINUTA Y KINUTA C
TO OVERALL BLOCK(4/4)
(SEE PAGE 3-8)
CN001 J001 AUDIO/VIDEO IN J002 (HEADPHONES) 5 7 5 7 HP L HP R CN104 44 42 43 41 1 2 13 1 2 13 L V R 38 40 37 39
22
FP-246(1/2)
(FLEXIBLE) (SEE PAGE 4-45)
XCS AU (IC4501) EX AUDIO L OUT EX AUDIO R OUT IR L IR R L R HP L HP R 55 56 57 58 52 54 20 21 22 23
VSP SO,VSP SI,XVSP,SCK
IR-38 BOARD
(SEE PAGE 4-27)
D362,363 (SUPER LASER LINK) 3 CN361 CN924 4
IC5701
AUDIO I/O 4 5 7 8 L R L R 3 2 15 16
(4-32)
IC5702
AUDIO A/D CONV. D/A CONV. 8 9 12 DATA TO SFD DATA FROM SFD SFD BCK TO OVERALL BLOCK(2/4)
(4-31)
(SEE PAGE 3-3)
EX-36 BOARD(1/2)
(SEE PAGE 4-63)
EX AUDIO L IN CN204 MULTI CONNECTOR 3 20 1 15 14 6 5 2 19 13 17 15 6 4 CN203 (GV-D800/D800E) CN5506 SP901 SPEAKER(L) 1 2 CN5503 2 1 26 25 CN5505 25 26 1 2 SP L+,L13 16 SP R+,RCN923 7 4 2 19 13 17 15 6 4 EX EX EX EX EX EX EX Y/V IN C IN VIDEO OUT AUDIO L OUT AUDIO R OUT AUDIO L IN AUDIO R IN 1 4 8 EX AUDIO R IN 11
IC5703
2 3 9 10 L R 64 3 8mm PB AUDIO PROCESS
14 26
AFM FSC (IC2201) PB RF
(4-31)
Y
CN931
IC5704
SPEAKER AMP 11 9 L R
SP902 SPEAKER(R)
1 2
(4-31)
PD-130 BOARD(1/3)
(SEE PAGE 4-55)
16
3-1
3-2
GV-D200/D200E/D800/D800E
3-2. OVERALL BLOCK DIAGRAM (2/4)
VC-250 BOARD(2/4)
Y0-Y7 Y0-Y7
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
CN1105 DV IN/OUT 138 139 142 L BUS 145 TRCK LCK VREF 42 47 79 X3301 24.576MHz
(4-15)
IC3301
199 203 207 213 1 5 9 201 205 211 215 3 7 16 17 21 23 (CAIN) DV SIGNAL PROCESS
(4-17)
45
CN929 6 9 29 MC BUS 37 TPA+,TPB+,2 5 4 1
CN1104
IC3303
(LIP) DV INTERFACE
C0-C7
C0-C7
51 141 151
FP-602
(FLEXIBLE) (SEE PAGE 4-17)
PB RF (IC3202 14 ) AFC FO (IC2201)
RF MON
16 5 2
CN933(1/2) FOR ADJUSTMENTS
HD, VD, OE
HD,VD,OE
152 PRRV,TRRV,TRRT 153 156 DATA TO SFD 133 DATA FROM SFD 132 SFD BCK 127 99 97 REC CK REC DT REC CK REC DT 40 42
DRUM
(4-12)
ODD FLYING ERASE
IC3103
(TRW) REC/PB AMP 6 7 2 1 Q3107 Q3109,3110 Q3112-3115 FILTER SW 35 31 1 4 2 ODD EVEN Q3104,3108 Q3111,3116 FLYING ERASE OSC
CN3101 10 9 12 13
IR FCS
182
34 83 AFCK (IC2603) SPCK (IC1505) TO OVERALL BLOCK(1/4) 8 196 48 6 88 81 79 20 19 HD VD 184 183 195 194 191 190 170 MC BUS 179 18 17 16 14 COL0 COL3 159 VSP SO, SI, SCK 161 163 162 75 73 71 105 106 PANEL G PANEL R PANEL B PANEL HD,VD XCS SFD (IC4501) XCS VFD (IC4501) XCS TRF (IC4501) PB CK ATF ERR PB CK AD DT 6 AD DT 6 15 20 13
(4-11)
IC3101
(TRF) EQ A/D CONV. PLL 25 22 24
42
PB Y OUT DV PB RF
27 29
16
EVEN
(SEE PAGE 4-11)
(SEE PAGE 3-2)
IC3302
CHARACTER GENERATOR
IC3102
(4-11)
XFE ON DRUM 8PB VC RF SWP DV RF SWP ATF ERR ERRV,TRRV,TRRT DRP SO,XDRP SCK
(4-15)
1 3
XCS OSD OSD SO XOSD SCK CAIN Y CAIN C KINUTA Y KINUTA C 55 59
MC BUS
VSP SO,VSP SI,XVSP SCK
VSP SO,VSP SI,XVSP SCK
(4-21)
(4-21)
OSCI AMPO 67 53
DV PB RF SPCK 81 198 SPCK VCK 5
IC2202
DATA TO SFD DATA FROM SFD SFD BCK VCO
IC2201
(KINUTA) HI8/STD8 PB Y/C PROCESS
(4-19)
(4-19)
IC1505
1/2 1 4
IC1504
27MHz XTAL OSC 4 2
X1501 27MHz
AFC FO AFM FSC 79 139 Y0-Y7 122 112 C0-C3 199 HD,VD,OE 146 144 142 4 213
(4-13)
101 100 51 CK CONT 1,2(IC4902) RF AGC OUT 9
TO OVERALL BLOCK(3/4)
IC3201
HI8/STD8 PB RF AMP 18 ADJUSTMENT VOLTAGE 36 PB C RF 11 3
(4-13)
(SEE PAGE 3-5)
IC2291
D/A CONV. (EVR) 1 2
IC1502
196 AD1-AD10 187 185 AD CK 11 16 2 A/D REC 34 PB RF 14 PB
Y C MECHA HD MECHA VD MECHA FLD TBC VD
(4-19)
46 48
(4-13)
DA STB (IC4902)
IC3202
5 DOP 7 3 RF ENV DET 4 RF ENV DET
49 93 94 89 168 95 96 97 98 77
PB C RF
MECHA HD MECHA VD MECHA FLD TBC VD XCS CH CH SO XCH SCK
XCS KINUTA(IC4902)
VC SO,VC SI,XVC SCK PB RF Y PANEL R PANEL G PANEL B PANEL HD,VD
TO OVERALL BLOCK(4/4)
XCS OSD OSD SO XOSD SCK
(SEE PAGE 3-8)
16
3-3
3-4
GV-D200/D200E/D800/D800E
3-3. OVERALL BLOCK DIAGRAM (3/4)
VC-250 BOARD(3/4)
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
(4-33) (4-35)
DRUM PWM CAP PWM DRUM PWM CAP PWM
FU-145 BOARD(1/2)
(4-33)
29 27 DRUM ERROR CAP ERROR
B710-MECHA DECK
(SEE PAGE 4-56)
CN4402 DRUM YS 6 M901 DRUM MOTOR CN921 Q1306 SWITCHING SWITCHING Q1305 3 4 1 2 CN1301 3 4 1 2
DRP SO,DRP SI,XDRP SCK
78 79 80 74 75 76 26
IC4501
DIGITAL8 MECHA CONTROL SIGNAL PROCESS CONTROL
IC4401
28 25
IC1301
9 9 15 11
68 69
(3/3)
LPF
(1/2)
PWM DRIVE
58 64
IC4401
(1/3)
DRUM MOTOR DRIVE
10 10 CN921 CN1301
61 59 57
U, V, W
10 5
M
VSP SO,VSP SI,XVSP SCK
(4-49)
DRUM FG DRUM PG DRUM FG DRUM PG
MC BUS 38 FRRV,TRRT,TRRV 106 107 108 95
16 22
FG AMP PG AMP
17 20
3 1
DRUM FG DRUM PG
116 117 115 110 109 96 39 40 41 49 50
ATF ERR
CN4403 CAP FG DEW DET CAP FG MODE SW A-C LOAD UNLOAD CAP VS 8 7 1
M902 CAPSTAN MOTOR
M
CAPSTAN FG
2
3
4
IC4502
EEPROM 1
XCS VFD (IC3301) XCS SFD (IC3301) XCS TAKO (IC3701) XCS EEP XCS AU (IC5701) XCS TRF (IC3101) VREF (IC3301)
17 28 18 88 21 23 112 62 59 111 99
DEW DET
12
DEW SENSOR
(4-36)
DV RF SWP XFE ON DRUM 8 PB RF ENV DET
CN4401 MODE SW A-C 54 53 114 113 55 44 TAPE END TAPE TOP T REEL FG S REEL FG TAPE LED ON REC PROOF TAPE END 47 LOAD UNLOAD 2 3 4 S901 MODE SWITCH
(4-33)
XCS MECHA (IC4803)
72 81 82 83 1
IC4401
(2/3)
55 56 LOADING MOTOR DRIVE TAPE END DETECT TAPE TOP DETECT T REEL FG AMP S REEL FG AMP 53 51 LM(+),LM(-) 5 8
M903 LOADING MOTOR
HI SO,HI SI,XHI SCX
M
Q002 D001 TAPE LED
46
TAPE END(C)
8 Q001 2 12 11 5 4
(4-29)
TO OVERALL BLOCK(2/4)
TAPE END SENSOR TAPE TOP SENSOR T REEL SENSOR S REEL SENSOR H001
(4-29)
TAPE TOP X4901 20MHz 1 LINE OUT V (IC3301) 2 1 114 39 78 79 80 19 21 27 111 112 113 118 47 83 82 81 CK CONT 1,2 (IC2201) 104 110 74 75 76 78 42 41 96 95 31 HI SO,HI SI,XHI SCX 38 40 XCS VC (IC4803) TAPE END TAPE TOP T REEL AFG S REEL AFG TAPE LED ON ME SW HI8 MP SW XCS LCD (IC4803) 13 14 PANEL R PANEL G PANEL B 22 21 20 5 6 7 48 47 46 41 40 39
IC4902
HI8/STD8 MECHA CONTROL
69 68 116 117 115 109 35 36 37 32 33
DRUM PWM CAP PWM DRUM FG DRUM PG
44
45 38 39 36 35
TAPE TOP(C)
(SEE PAGE 3-4)
IC4901
EEPROM 2 3 4
T REEL FG 41 T REEL AFG 39 S REEL FG 33 S REEL AFG 34
T REEL(+),(-)
S REEL(+),(-)
H002
CAP FG TAPE LED ON MODE SW A-C LOAD UNLOAD Q4401 LED DRIVE REC PROOF ME SW HI8 MP SW XCC DOWN 14 S001 7 6 3 15 REC PROOF ME/MP HI8 MP CC DOWN S002
VC SO,VC SI,XVC SCX
VC SO,VC SI,XVC SCX XCS KINUTA (IC2201) DA STRB (IC2291) XCS EEPROM
MECHA FLD MECHA HD MECHA VD TBC VD
CN4404
(GV-D800/D800E)
VC RF SWP XCS CH,CH SO,XCH SCK
PD-130 BOARD(2/3)
HD OUT PANEL COM VR,VG,VB
8 4 5 3 1 19 20 21
CN5502 FOR ADJUSTMENTS
IC5501
RGB DRIVE
20 VR,VG,VB 22 24 27 COM DA VCOM VGLAC
LCD UNIT
ND901 BACKLIGHT BL HIGH 10
T5601 Q5602 INVERTER BACK LIGHT DRIVE BL REG
11 4 5 10 12
PANEL R PANEL G PANEL B PANEL HD,VD
(4-55)
35
(4-57)
44 XCC DOWN HI SO,XHI SCK TO OVERALL BLOCK(4/4) PANEL HD PANEL VD 14 12 17 16 13 15 10 11 HD OUT BL CONT DV RF SWP (IC4501 62 ) VC RF SWP (IC4902 47 ) 46 45 42 1 48
IC5502
TIMING GENERATOR
IC5602
BL LOW CN5604 3 3 CURRENT DET 4
10 24 Q5601 9
18 CN5501
HI SO,HI SI,XHI SCK
(4-55)
2 8 5
(SEE PAGE 3-8)
BL DET 5 1 2 7 6 PANEL 2.8V
(4-57)
BL CONT CN923 8 13 15 CN933(2/2) FOR ADJUSTMENTS 4 23 CN5503
IC5601
16
3-5
3-6
GV-D200/D200E/D800/D800E
3-4. OVERALL BLOCK DIAGRAM (4/4)
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
(GV-D800/D800E)
FK-78 BOARD
(SEE PAGE 4-61)
CN001 S001016 FUNCTION SWITCH 6 6 · · 5 5 · · 7 7 2 2 4 4 3 3
VC-250 BOARD (4/4)
(4-37)
IC4803
HI CONTROL
PD-130 BOARD (3/3)
S5601, 5602 23 CN923 80 3 58 27 XCS MECHA (IC4501) XCS VC (IC4902) XCS ALIGN (IC3603) XCS LCD (IC5501, 5502) XCC DOWN TO OVERALL BLOCK(3/4) LCD BRIGHT AD6 1 4 SW CN5608 CN5503 1
LS-56 BOARD
S001 LCD ON/OFF SW CN001
93 KEY AD0 · 94 KEY AD1 · 95 KEY AD2 X REC LED X PAUSE LED X CAUTION LED X4801 20MHz X4802 32.768kHz 5 Q906908 LED DRIVE
KEY AD6 99
D001 (REC) D002 (PAUSE) D003 (CAUTION)
XCS MECHA XCS VC 6 X REC LED XCS ALIGN 8 X PAUSE LED XCS LCD
(SEE PAGE 4-57)
(SEE PAGE 4-56)
55 X CAUTION LED 40 41 52 53 20MHz OUT 20MHz IN 32kHz IN 32kHz OUT
XCC DOWN 18
(SEE PAGE 4-37)
(4-37)
HI SO, HI SI, XHI SCK BL CONT HI SO HI SI HI SCK 33 · 34 · 35
IC4801
CN926 BT001 1 · 2 BATT LI 3V VTR UNREG BATT UNREG 3 7 RESET
(SEE PAGE 3-5)
TO OVERALL BLOCK(1/4)
FP-571
(FLEXIBLE)
VANADIUM LITHIUM BATTERY
VDD SWITCH
6 S4801 RESET
38 XRESET 42 · 51 · VDD 77 · 87
HI SO, HI SI, XHI SCK SIRCS, PWM XCS OSD OSD SO XOSD SCK Q4802, 4805 MOD Q4803 MOD
(SEE PAGE 3-2)
TO OVERALL BLOCK(2/4)
IO-68 BOARD (2/2)
(SEE PAGE 4-45)
EXEC S103 SEL/PUSH EXEC DIAL S101, 102, 104, 105 VOLUME SW MENU SW S. LASER LINK SW CN103 23 26 · 25 CN922 24 25 · 26
XCS OSD OSD SO XOSD SCK
44 · 45 · 46
(SEE PAGE 3-3)
FU-145 BOARD (2/2)
(4-49)
SIRCS ENV 59 MELODY 36 98 KEY AD5 MELODY ENV 56 67 DIAL A · 68 DIAL B
IC1301
(GV-D800/D800E) BL CONT 42 46 · 45 44 43 26 · 25 22 | 19 16 · 15 · 14 13 8 · 7 32 · 31 30 29 35 36 39 38 37 42 46 · 45 44 43 26 · 25 22 | 19 16 · 15 · 14 13 8 · 7 32 · 31 30 29 35 36 39 38 37 VTR UNREG BATT UNREG FAST CHARGE BATT/EXT SW BATT SIG CN1301 Q502 DC-DC CONVERTER (2/2)
FP-246 (2/2)
(FLEXIBLE)
(POWER) (CHARGE)
D001 CN001
CN104 X POWER LED 8 8 X CHARGE LED 10 10
Q48084810 46 43 45 44 LED DRIVE
BATT/EXT SW FAST CHARGE VTR DO ON SHOE ON 5 X POWER LED 57 X CHARGE LED
66 50 29 81
BL REG PANEL 15V PANEL 13V
1.5V 2.8V
IC001
REMOTE COMMANDER 1 RECEIVER 14 14 SIRCS SIG 45 46 S4802 EJECT SW 4 SIRCS SIG
4.75V 17 X EJECT SW RP UNREG MT 5V 1 1 2 2 LANC SIG CN105 2 1 1 2 14 X VTR MODE SW 72 ID1 · 73 ID2 48 IB SI · 49 IB SO 10 · 11 23 | 26 8 39 · 40 10 · 11 23 | 26 8 39 · 40 CN931 LANC IN 1 · LANC OUT 2 Q4804 EX UNREG SHOE ON VTR DO ON VTR UNREG BATT UNREG
(SEE PAGE 4-45)
J001 (LANC)
FP-575
(FLEXIBLE)
S001 POWER OFF ON
Q507 CN502 1 2 3 1 5 4 J902 DC IN
(SEE PAGE 4-45)
EX-36 BOARD(2/2)
11, 17 CN204 18, 19 MULTI CONNECTOR 8 LANC SIG BZ201 BUZZER CN203
CN501
+
S
(4-37)
EX UNREG LANC SIG BEEP
IF
BATT SIG
J901 BATTERY TERMINAL
IC4802
10 11 LANC I/O · 12
CN921
16
(SEE PAGE 4-65)
3-7
3-8
GV-D200/D200E/D800/D800E
3-5. POWER BLOCK DIAGRAM (1/2)
FU145 BOARD
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
VC250 BOARD(1/2)
CN1301 CN921 31 32 31 32 EX UNREG EX UNREG
DC PACK SW SHOE ON BATT SIG INIT CHARGE ON VTR DD ON FAST CHARGE
J901 BATTERY TERMINAL CN501 BATT (+) BATT SW(+) BATT SW() BATT() BATT SIG Q501, 502
Q506, 507
F501 BATT/XEXT SW BATT UNREG BATT UNREG BATT UNREG
1 2
S
3 4 5
F502 Q503505 CHARGE SWITCH F504 F505 F503 (GVD800/D800E)
36
36
C/D VS D1.5V BL UNREG VTR UNREG
5V REG Q13101313
MT 5V
7 8
7 8
MT 5V
J902 DC IN 1 2 3 BATT/XEXT SW CN502 INIT CHARGE ON ACV UNREG
VTR UNREG 35 35
VTR UNREG
(GVD800/D800E) L501 BL CONT BL CONT FAST CHARGE DC PACK SW 42 42
EX UNREG
BL CONT
SHOE ON
(449)
IC1301
DC/DC CONVERTER
Q1309 SWITCHING
L1317
L1318
BL REG
45 46
45 46 L1309 L1320
BL REG PANEL 2.8V PANEL 13.3V PANEL 15.3V L1315 Q1322,1324,1326 PANEL 4.75V
7
NONINV INPUT7
OUTPUT7 OUTPUT MONITOR-7 OUTPUT VCC7 OUTPUT VCC4,5,6 OUTPUT4
2 6 Q1303 SWITCHING
31 STANDBY7
5 1 57 54
L1305
L1310
1.5V
25 26
25 26
15.3V REG (GVD800/D800E) L1313 AV 4.75V
TO POWER BLOCK(2/2)
28 VCC MOS GATE4 OUTPUT MONITOR4 18 COMP 41 Q1304 SWITCHING
Q1308 SWITCHING
(SEE PAGE 3-11)
(439)
1 5 L1307 L1308
IC1302
4 1.9V REG
19 L302 2.8V Q1314 EMERGENCY DETECT 20 21 22
19 20 21 22
D 1.9V
A 2.8V AU 2.8V D 1.5V
OUTPUT1 MOS GATE1 OUTPUT MONITOR1
45 42 40 T1301
Q1307 SWITCHING
OUTPUT VCC1,2,3 VREF 27 VREF OUTPUT3 OUTPUT MONITOR3
49
Q1301 SWITCHING 4
D1302 (1/2) RECT 5 6 7 8 2 D1302 RECT D1301,305 RECT D1306 RECT
PANEL 13V RP UNREG
43 13
43 13
50 34
1
L1314 PANEL 15V 44 14 15 16 44 14 15 16 L1321
A 4.75V
21 RT 22 CT Q1302 SWITCHING
3
L1301
4.75V
OUTPUT2 VTR DD ON
46
L1306
D 2.8V
29 STANDBY3 30 STANDBY
OUTPUT MONITOR2
37
Q1305 SWITCHING
L1303
CAP VS
CAP VS CAP ERROR DRUM VS
1 2
1 2 10 3 4 9 L1316
CAP VS CAP ERROR DRUM VS DRUM ERROR RP 4.75V
OUTPUT6 OUTPUT MONITOR6 NONINV INPUT6
64 10 11 CAP ERROR Q1306 SWITCHING
10 3 4
DRUM ERROR L1304 DRUM VS VTR DD ON
9
29 30 37 38 39 40 41
29 30 37 38 39 40 41 L1311 2 5
OUTPUT5 58 OUTPUT MONITOR5 14 NONINV INPUT5 15 DRUM ERROR
SHOE ON BATT SIG BATT/XEXT SW FAST CHARGE INIT CHARGE ON DC PACK SW
IC1303
5.9V REG
RP 6.0V 3
(439)
16
3-9
3-10
GV-D200/D200E/D800/D800E
3-6. POWER BLOCK DIAGRAM (2/2)
VC-250 BOARD(2/2)
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
BT001 VANADIUM LITHIUM BATTERY
BATT LI3V CN926
1 2
FP-571 (FLEXIBLE)
(SEE PAGE 4-37)
IC4803 (4-37)
DC PACK SW SHOE ON BATT SIG INIT CHARGE ON VTR DD ON FAST CHARGE BATT XEXT SW BATT UNREG D4802 2 D4801 MT 5V 7 REG BATTER IN DETECT HI CONTROL SHOE ON 81 90 BATT SENS 91 ACV SENS Q4804 IB SO 49 IB SI 48 INIT CHARGE ON 25 VTR DD ON 29 FAST CHARGE 50 CHARGE INH 47 BATT/XEXT 66 XVTR MODE SE 14 XPOWER LED 5 Q4806 12 XLANC ON XCHARGE LED 57 S4801 RESET DC PACK SW 22 45 44 47 21 46 43 48 I/F BATT SIG 1 5 2 6
(SEE PAGE 4-45)
IO-68 BOARD
XVTR MODE SW LANC SW CN105 LED EVER 3.0V XPOWER LED XCHARGE LED A 4.75V CN104 12 11 RFU DC OUT CN103 CN001 6 8 10 12 6 8 10 12 1 6
S001 POWER ON OFF
FP-575 (FLEXIBLE)
(SEE PAGE 4-45)
J001 (LANC)
(4-37)
IC4801 (4-37)
D901 3 3 RESET 5 6 4 8 38 XRESET 42 51 VDD 86 87 61 BATT IN
IC901
REG
IC001
D001 (POWER) (CHARGE) REMOTE COMMANDER RECEIVER
(4-45)
IC4802 (4-37)
LANC I/O 1 UNREG LANC DC 14 LANC DC POWER 4 VCC 8
VTR UNREG EX UNREG BL CONT BL REG
Q4809,4810 LED DRIVE Q4808 LED DRIVE
FP-246 (FLEXIBLE) (SEE PAGE 4-45)
J102 RFU DC OUT (GV-D800/D800E) Q5502-5506 24 3 18 23 CN5501 5 4 2
PANEL 2.8V PANEL 13.3V PANEL -15.3V PANEL 4.75V
VTR UNREG MT 5V AU 4.75V
PD-130 BOARD
(4-36) (4-31) (4-31) (4-31) (4-31) (4-35)
IC5701
AU 4.75V AUDIO I/O
IC5702
AUDIO ADC&DAC L5701 FB3303
IC5703
AUDIO INPUT SELECT
IC5704
SPEAKER AMP (GV-D800/D800E)
IC4502
EEPROM
IC4501
DIGITAL8 MECHA CONTROL
Q904,905 CURRENT LIMITER
PANEL 4.75V PANEL -15.3V PANEL 13.3V PANEL 2.8V BL CONT
9 5 6 10 4 CN923
18 22 6 17 23
PANEL 4.75V PANEL -15.3V PANEL 13.3V PANEL 2.8V BL CONT CN5503
L5504 L5503 L5501 L5502
LCD UNIT
(4-55)
(SEE PAGE 4-61)
IC5501
RGB DRIVE
IC5502
TIMING GENERATOR 28
D 1.9V A 2.8V TO POWER BLOCK (1/2) AU 2.8V
A 2.8V AU 2.8V D 2.8V FB3601 L3602 FB3701 FB3370 REG 1.5V EVER 3.0V FB2291
FK-78 BOARD
FB4501 D 2.8V CN927 1 1 CN001 LED
(4-55)
IC5503
(4-56)
ND901 BACKLIGHT
(SEE PAGE 3-10)
D 1.5V
IC5601,5602
INVERTER BL HIGH 1 CN205 2 BL REG CN5607 BACKLIGHT DRIVE 10
IC3603
(ALIGN) A/D CONV.
IC3701
(TAXO) VIDEO LINE IN/OUT AMP L3701, 3705
IC3301
(CAIN) DV SIGNAL PROCESS
IC3303
(LIP) DV INTERFACE
IC3302
CHARACTER GENERATER
IC2291
(EVR) D/A CONV. 34 36 23 34 36 23 26
EX-36 BOARD
BL REG
(4-57)
CN5604
(4-23)
A 4.75V A 4.75V A 2.8V MT 5V D 1.5V D 2.8V L3707
(4-26)
(4-15)
(4-17)
(4-15)
L2291
(4-13)
EX UNREG
18 19 CN203
CN204 MULTI CONNECTOR
26 CN931
D 2.8V
(SEE PAGE 4-65)
L3706 L3901
(4-25)
CAP VS CAP ERROR DRUM VS DRUM ERROR
(4-27)
L2204 L2209
IR DRV Q3903
FB2203, FB2205
FB2202
FB2204
IC3703
VIDEO OUT AMP
IC3702
VIDEO INPUT SELECT
L2201-2203, L2208
FB1504
L1501
CAP VS
IC3901
IR TRANSMITTER 24
(4-33) (4-29) (4-29)
7 8 9 10 CN4403 SENSOR VCC R4407 13
CAPSTAN MOTOR
IC2201
HI8/STD8 PB Y/C PROCESS
IC1502
(4-21)
AGC, A/D CONV.
IC4901
EEPROM
IC4902
HI8/STD8 MECHA CONTROL DRUM ERROR 29 CAP ERROR 27 DRUM VS 6
IC4401
(RABI) DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP
(4-25)
RP 4.75V RP 4.75V A 2.8V D 2.8V FB1501 L3201
(4-19)
T REEL, S REEL SENSOR
L3102 L3104
RF 1.9V L3103
FB4901
D 2.8V VTR UNREG MT 5V R4411
IC1504
XTAL OSC
IC1505
FREQUENCY DIVIDER
IC3201
HI8/STD8 PB RF AMP
IC3202
RF ENV DET
IC3103
(TRW) REC/PB AMP
IC3101
(TRF) EQ. A/D CONV. PLL
TAPE LED(A) CN4404
9
TAPE LED
(4-19)
RP 6.0V
(4-19)
(4-13)
(4-14)
(4-12)
(4-11)
IR DRV
Q901-903 IR 5V CN924 1 2 1 2 CN361
F361
D362,363 IR LED SUPER LASER LINK
IR-38 BOARD
(SEE PAGE 4-27)
B710 MECHA DECK
(SEE PAGE 4-33)
16
3-11
3-12E
SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
GV-D200/D200E/D800/D800E
17
18
19
A
J102 VIDEO OUT CN5713 50P LANC_SIG RFU DC OUT L XLANC_JACK_IN 4 5 6 7 8 9 4 5 6 7 8 9 XVTR_MODE_SW REG_GND (MONO) R 1 2 3 1 2 3
FP-247
FLEXIBLE
CN002 LANC_SIG XVTR_MODE_SW REG_GND XLANC_JACK_IN REG_GND LANC_DC LCH_DET RCH_DET AUDIO_GND AUDIO_R_OUT RF_DC_OUT AUDIO_L_OUT VIDEO_OUT_GND V_JACK_OUT_DET S_C_GND VIDEO_OUT S_Y_GND S_C_OUT REG_GND S_Y_OUT EVER_3.0V XS_JACK_OUT KEY_AD5 XIR_LED_ON DIAL_B DIAL_A S_Y_GND XS_JACK_IN S_C_GND S_Y_IN REG_GND S_C_IN VIDEO_GND AV_JACK_IN REG_GND VIDEO_IN AUDIO_GND AUDIO_L_IN XHP_SENS AUDIO_R_IN HP_GND HP_R XCHRGE_LED HP_L XSIRCS_LED XPOWER_LED REG_GND A_4.75V REG_GND REG_GND 50P CN001 50P XVTR_MODE_SW LANC_SIG XLANC_JACK_IN REG_GND LANC_DC REG_GND RCH_DET LCH_DET AUDIO_R_OUT AUDIO_GND AUDIO_L_OUT RF_DC_OUT V_JACK_DET VIDEO_OUT_GND VIDEO_OUT S_C_GND S_C_OUT S_Y_GND S_Y_OUT REG_GND XS_JACK_OUT_DET EVER_3.0V XIR_LED_ON KEY_AD5 DIAL_A DIAL_B XS_JACK_IN S_Y_GND S_Y_IN S_C_GND S_C_IN REG_GND AV_JACK_IN VIDEO_GND VIDEO_IN REG_GND AUDIO_L_IN AUDIO_GND AUDIO_R_IN XHP_SENS HP_R HP_GND HP_L XCHARGE_LED XPOWER_LED XSIRCS_SIG A_4.75V REG_GND REG_GND REG_GND 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 CN922 50P XVTR_MODE_SW 1/16 LANC_SIG 2/16 XLANC_JACK_IN 3/16 REG_GND 4/16 DV INTERACE AD CONVERTER Y/C PROCESSOR LINE A/D LINE IN/OUT IR MECHANISM CONTROL AUDIO I/O DRUM/CAPSTAN MOTOR DRIVE MECHA CONTROL HI CONTROL DC/DC CONVERTER CONNECTION LANC_DC 5/16 LANC_DC LCH_OUT_DET RCH_OUT_DET D109 (SUPER LASER LINK) C S VIDEO OUT S G G Y S REG_GND AUDIO_R_OUT RF_DC_OUT AUDIO_L_OUT VIDEO_OUT_GND S103 V_JACK_OUT_DET S_C_GND SEL/PUSH EXEC J101 C S VIDEO IN S G G Y S VIDEO_OUT S_Y_GND S_C_OUT REG_GND S_Y_OUT EVER_3.0V XS_JACK_OUT_DET KEY_AD5 XIR_LED_ON DIAL_B DIAL_A S_Y_GND S101 SUPER LASER LINK XS_JACK_IN_DET S_C_GND S102 MENU S_Y_IN REG_GND S_C_IN S104 VOLUME+ VIDEO_GND AV_JACK_IN_DET S105 VOLUMEREG_GND VIDEO_IN AUDIO_GND CN105 POWER OFF-ON S001 J001 LANC 1 2 3 4 5 6 XVTR_MODE_SW AUDIO_R_IN LANC_SIG HP_GND REG_GND HP_R REG_GND XCHRGE_LED REG_GND HP_L LANC_DC XSIRCS_LED XPOWER_LED REG_GND A_4.75V REG_GND REG_GND 45 45 46 46 47 47 48 48 49 49 50 50 45 45 46 46 47 47 48 48 49 49 50 50 XPOWER_LED XSIRCS_SIG A_4.75V REG_GND REG_GND REG_GND 35 37 39 41 43 45 47 VTR_UNREG BATT_SIG FAST_CHARGE DC_PACK_SW PANEL_13V BL_REG REG_GND BATT_UNREG BATT/XEXT_SW INIT_CHARGE BL_CONT PANEL_-15V BL_REG REG_GND 36 38 40 42 44 46 48 35 37 39 41 43 45 47 VTR_UNREG BATT_SIG FAST_CHARGE DC_PACK_SW PANEL_13V BL_REG REG_GND BATT_UNREG BATT/XEXT_SW INIT_CHARGE BL_CONT PANEL_-15V BL_REG REG_GND 36 38 40 42 44 46 48 44 44 44 44 XCHARGE_LED 33 REG_GND REG_GND 34 33 REG_GND REG_GND 34 43 43 43 43 HP_L 31 SHOE_UNREG SHOE_UNREG 32 31 SHOE_UNREG SHOE_UNREG 32 42 42 42 42 HP_GND 29 VTR_DD_ON SHOE_ON 30 29 VTR_DD_ON SHOE_ON 30 41 41 41 41 HP_R 27 REG_GND REG_GND 28 27 REG_GND REG_GND 28 BATT/XEXT 3 3 BATT/XEXT 40 40 40 40 XHP_SENS 25 1.5V 1.5V 26 25 1.5V 1.5V 26 ACV_GND 2 2 ACV_GND DC IN 6P AUDIO_L_IN XHP_SENS REG_GND 6/16 RCH_OUT_DET 7/16 LCH_OUT_DET 8/16 AUDIO_R_OUT 9/16 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 REG_GND 10/16 AUDIO_L_OUT 11/16 RF_DC_OUT 12/16 V_JACK_OUT_DET 13/16 VIDEO_OUT_GND 14/16 VIDEO_OUT 15/16 S_C_GND 16/16 S_C_OUT S_Y_GND S_Y_OUT REG_GND XS_JACK_OUT_DET EVER_3.0V XIR_LED_ON KEY_AD5 DIAL_A DIAL_B XS_JACK_IN_DET S_Y_GND S_Y_IN S_C_GND S_C_IN REG_GND AV_JACK_IN_DET VIDEO_GND VIDEO_IN REG_GND AUDIO_L_IN AUDIO_GND AUDIO_R_IN 1 3 5 7 9 11 13 15 17 19 21 23 CAP_VS DRUM_VS MT_GND MT_5V DRUM_ERROR REG_GND RP_UNREG 4.75V REG_GND 2.8V 2.8V REG_GND CN921 CAP_VS DRUM_VS MT_GND MT_5V CAP_ERROR REG_GND 4.75V 4.75V REG_GND 2.8V 2.8V REG_GND 48P 2 4 6 8 10 12 14 16 18 20 22 24 B TO B 1 3 5 7 9 11 13 15 17 19 21 23 CAP_VS DRUM_VS MT_GND MT_5V DRUM_ERROR REG_GND RP_UNREG 4.75V REG_GND 2.8V 2.8V REG_GND CN1301 CAP_VS DRUM_VS MT_GND MT_5V CAP_ERROR REG_GND 4.75V 4.75V REG_GND 2.8V 2.8V REG_GND 48P 2 4 6 8 10 12 BATT_SW(+) 14 BATT_SW(-) 16 BATT(-) 18 BATT_SIG 20 22 CN502 24 ACV_UNREG 1 1 ACV_UNREG 3P CN902 3P 5 5 BATT_SIG 4 4 BATT(-) 3 3 BATT_SW(-) 2 2 BATT_SW(+) BATTERY TERMINAL CN501 5P BATT(+) 1 1 BATT(+) CN901 5P DV INTERACE PB AMP,DAC REC/PB ANP
VC-250 BOARD(1/2)
B
AUDIO 0UT
IO-68 BOARD
REG_GND
TO(2/2)
J103
C
D
FU-145 BOARD
E
S
F
FP-575
FLEXIBLE
G
CN104
H
16P
AV_JACK_IN_DET
XPOWEER_LED
XCHARGE_LED
AUDIO_R_IN
XSIRCS_SIG
AUDIO_L_IN
EVER_3.0V
XHP_SENS
VIDEO_IN
HP_GND
AV_GND
AV_GND
A_4.75V
HP_R
HP_L
GND
CN924
10P IR_5V IR_5V 1 2 1 IR_5V 3 2 IR_CL_OUT IR_ME_OUT IR_GND KEY_AD3 REG_GND 4 5 6 7 6 8 CN361
IR-38 BOARD
6P D362,363 (SUPER LASER LINK)
10
11
12
13
14
15
I
1 2 3 4 5 6 7 AUDIO_L_IN VIDEO_IN HP_L EVER_3.0V HP_R AV_GND AV_JACK_IN_DET
16
1
2
3
4
5
6
7
8
9
B to B CN1105 4P 1 NTPB 1 2 DV IN/OUT TPB NTPA TPA 2 3 3 4 4 5 NTPB TPB TPA NTPA GND CN929 5P
IR_CL_OUT IR_EM_OUT IR_GND IR_GND IR_GND KEY_AD3 REG_GND REG_GND
FP-572
FLEXIBLE
10
11
12
13
14
15
16
3 4 5
8 XPOWER_LED
XHP_SENS
9
HP_GND
AUDIO_R_IN
XCHARGE_LED
XSIRCS_SIG
A_4.75V
AV_GND
GND
16P
(SUPER LASER LINK) 9 10
CN001
J
J002
FP-602
D001 POWER/ CHARGE
FLEXIBLE
IC001 CN927 10P D_2.8V 1 2 3 4 STOP/ KEY_AD1 KEY_AD0 CN926 4P KEY_AD2 1 2 3 4 LI_3V REG_GND LI_3V REG_GND GND REG_GND GND REC/CAUTION/PAUSE 10 9 8 D001~D003 7 5 FRAME-/ 6 DIGITAL EFFECT/TITLE/PB ZOOM FLAME+/SLOW/DATE CODE/DISPLAY/ PLAY/REC / FF/ REW/PAUSE/X2/
(HEADPHONES) XREC_LED J001 XCAUTION_LED XPAUSE_LED
CONTROL SWITCH BLOCK S001~S016 (FK-78)
K
AUDIO/VIDEO IN
FP-246
FLEXIBLE
BT001 LITHIUM BATTERY
L
FP-571
FLEXIBLE
M
16
4-1
4-2
FRAME SCHEMATIC DIAGRAM (1/2)
GV-D200/D200E/D800/D800E
FRAME SCHEMATIC DIAGRAM (2/2)
1 2
GV-D800/D800E MODEL ND901 BACK LIGHT
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
A
LCD 901
4 INCH COLOR LCD UNIT
10P
STBYB
STBYB
RESET
VCOM
MCLK
GPCK
GRES
HCNT
GSRT
VGH
VDD
VDD VSH3V 23
LED_GND
BL_LOW
BL_HIGH
VDD3V
LS-56 BOARD
CN01 2P AD_6 S001 (LCD ON/OFF) GND 1 2
PL-53
HARNESS
1 2 AD_6 GND CN5608
10
11
12
13
14
15
16
17
18
19
20
21
22
10
24
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
9
VSH5V
VCOM
PSS1
PSS2
MO1
MO2
MO3
GND
GND
VGH
SPD
SPS
VGL
RES
CTR
CLD
N.C
N.C
N.C
LED
N.C
N.C
N.C
CLS
EX1
EX2
VR
VG
VB
VSH
VSS
VBC
VSS
N.C.
VGL
CLR
SRT
VR
VG
VB
OE
B
CN5604
CN5501
24P
CN5502
10P VB 1 2 3 4 5 6 7 8 9 10 CPC (FOR CHECK)
2P S5601 BLIGHT+ LCD S5602 BLIGHT-
C
XVD_OUT
PD-130 BOARD
LCD DRIVER(1/2) BACK LIGHT(2/2)
VG PANEL_COM VR SHARP/XCASIO C-SYNC/XHD
CN5506 SP901 SPEAKER L 1 2 SP_L_+ SP_L_-
2P
26P
2P
XHD_OUT GND GND
PANEL_-15.3V
PANEL_2.8V
PANEL_XVD
2
SP_R_-
PANEL_HOLD
XCS_LCD_DA
PANEL_13.3V
PANEL_4.75V
C-SYNC/XHD
D
SP902 SPEAKER R
1
SP_R_+
CN5503
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
XVC_SCK
BL_CONT
PANEL_G
PANEL_R
PANEL_B
CN5607
CN5505
2P
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
2
BL_HIGH
BL_LOW
SP_R_+
SP_L_+
SP_R_-
SP_L_-
VC_SO
AD_6
E
10 11 1 2 3 4 5 6 7 8 REG_GND REG_GND REG_GND 9 REG_GND SP_R_+ BL_CONT SP_R_PANEL_13.3V PANEL_4.75V PANEL_-15.3V CN933 1 2 3 4 SWP AFC_FO BPF_MONI F0_ADJ_RF_IN PB_RF REG_GND RF_AGC_OUT VC_RF_SWP NC(EVF_BL) NC(EVF_BL_4.6V) NC(VCO) NC(EVF_VG) DV_RF_SWP RF_IN CAP_FG RF_MON TMS TCK TDO TDI CPC (FOR CHECK) 20P 32P PANEL_2.8V
FP-569
12 13 14 15 16 17 REG_GND XCS_LCD_DA XVC_SCK VC_SO C-SYNC/XHD PANEL_XVD
EP-51
FLEXIBLE
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
HARNESS
CN205 1 2 BL_HIGT BL_LOW
2P
REG_GND
REG_GND
AD_6
SP_L_+
SP_L_-
NC
NC
NC
NC
NC
PANEL_-HOLD
PANEL_B
PANEL_G
PANEL_R
NC
CN931
40P VIDEO_GND V/Y_IN V/Y_IN_GND AUDIO_R_IN AUDIO_R_IN_GND AUDIO_L_IN AUDIO_L_IN_GND LANC_SIG LANC_GND ID1 ID2 VIDEO_GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 2 3 4 5 6 7 8 9 10 11 12 VIDEO_GND V/Y_IN V/Y_IN_GND
CN203
40P
F
CN923
EX-36 BOARD
BZ201 BUZZER
5 6 7 8 9 10 11 12
AUDIO_R_IN AUDIO_R_IN_GND AUDIO_L_IN AUDIO_L_IN_GND LANC_SIG LANC_GND ID1 ID2 VIDEO_GND VIDEO_OUT VIDEO_OUT_GND AUDIO_R_OUT AUDIO_R_OUT_GND AUDIO_L_OUT AUDIO_L_OUT_GND C_IN VIDEO_GND IO_GND IO_GND EX_UNREG EX_UNREG EX_UNREG EX_UNREG REG_GND REG_GND REG_GND REG_GND BL_GND BL_GND BL_GND BL_REG BL_REG BL_REG REG_GND REG_GND BEEP BEEP CN204 20P VIDEO_OUT VIDEO_OUT_GND V/Y_IN VIDEO_IN_GND AUDIO_R_IN AUDIO_L_IN AUDIO_IN_GND LANC_SIG IO_GND LANC_GND ID1 EX_GND EX_GND AUDIO_R_OUT AUDIO_L_OUT AUDIO_OUT_GND ID2 EX_UNREG EX_UNREG C_IN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MULTI CONNECTOR
G
13
TO(1/2)
14 15 16 17 18 19 20
VC-250 BOARD(2/2)
VIDEO_OUT VIDEO_OUT_GND AUDIO_R_OUT AUDIO_R_OUT_GND AUDIO_L_OUT AUDIO_L_OUT_GND C_IN VIDEO_GND
FP-570
FLEXIBLE
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
H
8P 16P 10P 12P 15P CN4401 CN3101 CN4402 CN4403 CN4404
IO_GND IO_GND EX_UNREG SENSOR_VCC TAPE_TOP(C) TAPE_END(C) TAPE_LED(A) TAPE_LED(K) EX_UNREG C_LOCK_SW EX_UNREG EX_UNREG REG_GND REG_GND REG_GND REC_PROOF
OFFSET_ADJ
FG-PG_COM
HALL_COM
STAND_BY
S_REEL(+)
COM_GND
M-SW(A)
M-SW(B)
M-SW(C)
XEVEN
YEVEN
LM(+)
LM(+)
XODD
YODD
LM(-)
LM(-)
LP2Y
LP2X
LP1X
LP1Y
GND
GND
GND
GND
GND
GND
FEY
FEX
I
10
11
12
T_REEL(+)
S_REEL(-)
T_REEL(-)
REG_GND
REG_GND
MT_GND
MT_GND
FG_OUT
HI8_MP
ME/MP
VCC_2
VCC_1
COM
DEW
FRC
PG
VS
VS
FG
W
W
U
U
V
V
13
10
10
10
11
12
13
14
15
16
11
14
12
FP-220
FLEXIBLE
10 12 10 11 12 14 16 11 10 13 15 2 3 4 6 8 1 9 5 7 6 5 6 5 4 2 4 2 8 8 3 1 3 1 7 9 7 9 M-SW(A) LM(+) W COM_GND FEY FEX PG FG M-SW(B) M-SW(C) LM(-) LM(+) LP2Y LP2X LP1X LP1Y SP1Y SP1X SP2X SP2Y COM GND GND GND GND GND GND W V V U U LM(-) FG-PG_COM FRC FG_OUT OFFSET_ADJ STAND_BY
FP-433
FLEXIBLE
14 13 12 15 11 6 5 4 8 3 2 7 1 MT_GND MT_GND VS VCC_2 REG_GND DEW S_REEL(+) VS VCC_1 HI8_MP S_REEL(-) REG_GND TAPE_TOP(C)
FP-221
FLEXIBLE
10 6 5 4 8 3 2 9 7 1 ME/MP REC_PROOF HALL_COM T_REEL(-) SENSOR_VCC TAPE_END(C) TAPE_LED(A) TAPE_LED(K) C_LOCK_SW T_REEL(+)
15
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7