Text preview for : SONY DCR-VX2100, VX2100E SERVICE MANUAL LEVEL 2 VER 1.4 2008.10 REV-1 (9-876-288-35).pdf part of SONY DCR-VX2100 SONY DCR-VX2100, VX2100E.
DIGITAL VIDEO CAMERA RECORDER.
SERVICE MANUAL VER 1.4 2008.10 REVISION-1
PART#(9-876-288-35).
Back to : SONY DCR-VX2100, VX2100E | Home
DCR-VX2100/VX2100E
RMT-811
SERVICE MANUAL
Ver. 1.4 2008. 10
Revision History How to use Acrobat Reader
LEVEL
2
US Model Canadian Model Korea Model
DCR-VX2100
AEP Model UK Model Australian Model Chinese Model
DCR-VX2100E
Revised-1
Replace the previously issued SERVICE MANUAL 9-876-288-31, 9-876-288-81 and 9-876-288-82 with this Manual.
Photo : DCR-VX2100
E Model Hong Kong Model Tourist Model
DCR-VX2100/VX2100E
C MECHANISM
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987628851.pdf). · For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987628841.pdf). · For MECHANISM ADJUSTMENTS, refer to the "DV MECHANICAL ADJUSTMENT MANUAL C MECHANISM " (9-974-050-11). · Reference No. search on printed wiring boards is available.
On the VC-358 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the VC-358 board. Therefore, schematic diagram, printed wiring board, mounted parts location and electrical parts list of the FP-594 and VC-358 board are not shown. The following pages are not shown. Schematic diagram ............................. Pages 4-43 to 4-78 Mounted parts location .................. Pages 4-127 to 4-128 Printed wiring board ............................ Pages 4-113 to 4-118 Electrical parts list ......................... Pages 5-27 to 5-35 Waveforms ........................................... Page 4-121 to 4-123
DIGITAL VIDEO CAMERA RECORDER
DCR-VX2100/VX2100E
SPECIFICATIONS
Video camera recorder
System Video recording system 2 rotary heads Helical scanning system Audio recording system Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs48 kHz, stereo) Video signal DCR-VX2100: NTSC color, EIA standards DCR-VX2100E: PAL color, CCIR standards Usable cassette Mini DV cassette with the mark printed Tape speed SP: Approx. 18.81 mm/s LP: Approx. 12.56 mm/s Recording/playback time (using cassette DVM60) SP: 1 h LP: 1.5 h Fast-forward/rewind time (using cassette DVM60) Approx. 2 min and 30 s Viewfinder Electric viewfinder (color) Image device 1/3 type CCD (3 Charge Coupled Device) Approx. 380 000 pixels (Effective: Approx. 340 000 pixels) Lens Combined power zoom lens Filter diameter 58 mm (2 3/8 in) 12 (Optical), 48 (Digital) F1.6 - 2.4 Focal length 6 - 72 mm (1/4 - 2 7/8 in) When converted to a 35 mm still camera 43.2 - 518.4 mm (1 3/4 - 20 1/2 in) Color temperature Auto, nIndoor (3 200 K), Outdoor (5 800 K), Minimum illumination 1 lux (F1.6)
Input/Output connectors S video input/output Input/output auto switch 4-pin mini DIN Luminance signal: 1 Vp-p, 75 ohms, unbalanced Chrominance signal: DCR-VX2100: 0.286Vp-p DCR-VX2100E: 0.3Vp-p 75 ohms, unbalanced Video input/output Input/output auto switch RCA pin-jack, 1 Vp-p, 75 ohms, unbalanced Audio input/output Input/output auto switch RCA pin-jack, 327 mV, (at output impedance more than 47 kilohms) Output impedance with less than 2.2 kilohms Input impedance more than 47 kilohms Headphones jack Stereo minijack (ø 3.5 mm) LANC control jack Stereo mini-minijack (ø 2.5 mm) MIC jack Minijack, 0.388 mV low impedance with 2.5 to 3.0 V DC, output impedance 6.8 kilohms (ø 3.5 mm) Stereo type DV Interface 4-pin connector Speaker Dynamic speaker (ø 20 mm) LCD screen Picture 6.2cm (2.5 type) Total dot number 211 000 (960 220) General Power requirements 7.2 V (battery pack) 8.4 V (AC Adaptor) Average power consumption (when using the battery pack) During camera recording using LCD 4.7 W Viewfinder 4.0 W Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F)
Dimensions (approx.) 120 × 159 × 393 mm (4 3/4 × 6 3/8 × 15 1/2 in) (w/h/d) Mass (approx.) 1.5 kg (3 lb 6 oz) including the hood with a lens cap 1.6 kg (3 lb 9 oz) including the rechargeable battery pack, NP-F330 and cassette DVM60 Supplied accessories See page 5-37.
AC Adaptor AC-L15A/L15B
Power requirements 100 - 240 V AC, 50/60 Hz Current consumption 0.35 - 0.18 A Power consumption 18 W Output voltage DC OUT: 8.4 V, 1.5 A Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F) Dimensions (approx.) 56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in) (w/h/d) excluding projecting parts Mass (approx.) 190 g (6.7 oz) excluding power cord
Rechargeable battery pack NP-F330
Output voltage DC 7.2 V Capacity 5.0 Wh Dimensions (approx.) 38.4 × 20.6 × 70.8 mm (1 9/16 × 13/16 × 2 7/8 in) (w/h/d) Mass (approx.) 70 g (2.5 oz) Type Lithium ion Design and specifications are subject to change without notice.
--2--
DCR-VX2100/VX2100E
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
DCR-VX2100/VX2100E
TABLE OF CONTENTS 1.
1-1. 1-2. 1. 2.
SERVECE NOTE
NOTE FOR REPAIR ······················································· 1-1 SERVICE NOTE ····························································· 1-2 POWER SUPPLY DURING REPAIRS ·························· 1-2 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ····························································· 1-2 1-3. SELF-DIAGNOSIS FUNCTION ···································· 1-3 1. SELF-DIAGNOSIS FUNCTION ···································· 1-3 2. SELF-DIAGNOSIS DISPLAY ······································· 1-3 3. SELF-DIAGNOSIS CODE TABLE ································ 1-4
2.
DISASSEMBLY
2-1. LCD SECTION (HL-013, PD-217 BOARDS, INVERTER TRANSFORMER UNIT) ················································ 2-2 2-2. EVF SECTION (LB-100 BOARD) ································· 2-3 2-3. (UPPER) HANDLE BLOCK ASSEMBLY ···················· 2-3 2-4. FK-088, MA-430, MI-050, FT-092, RM-091, ZM-030 BOARDS ········································································· 2-4 2-5. CABINET (L) BLOCK ASSEMBLY, MECHANISM DECK, VC-358, DD-216, JK-267 BOARDS (FOR FORCE EJECT OF CASSETTE AND VTR SECTION CHECK) ························································ 2-6 2-6. CABINET (R) BLOCK ASSEMBLY ····························· 2-8 2-7. CABINET BOTTOM ASSEMBLY ································ 2-8 2-8. BATTERY PANEL BLOCK ASSEMBLY (MK-016, KP-013, MS-209 BOARDS) ·························· 2-9 2-9. EVF BLOCK ASSEMBLY ············································· 2-9 2-10. LA-028, DD-216, VC-358, JK-267 BOARDS, MECHANISM DECK ··················································· 2-10 2-11. LENS BLOCK ASSEMBLY, CENTER FRAME ASSEMBLY ·································································· 2-11 2-12. CD-512, SE-147 BOARDS, ZOOM LENS ASSEMBLY ··· 2-12 2-13. CONTROL SWITCH BLOCK (PS-4980), CONTROL SWITCH BLOCK (CF-4980) ······································· 2-12 2-14. CK-140 BOARD ··························································· 2-13 2-15. CONTROL SWITCH BLOCK (ED-4980), HINGE ASSEMBLY ·································································· 2-14 2-16. CIRCUIT BOARDS LOCATION ································· 2-15 2-17. FLEXIBLE BOARDS LOCATION ······························ 2-16
· LA-028 (1/3) (ZOOM/FOCUS DRIVE) SCHEMATIC DIAGRAM ···························· 4-19 · SE-147 (VAP SENSOR) SCHEMATIC DIAGRAM ···························· 4-19 · LA-028 (2/3) (VAP DRIVE) SCHEMATIC DIAGRAM ···························· 4-21 · LA-028 (3/3) (KEY IN/CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-23 · FP-188, FP-189 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-23 · KP-013 (SELECT DIAL), MK-016 (CONTROL KEY), MS-209 (MS CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-25 · ZM-030 (ZOOM SWITCH) SCHEMATIC DIAGRAM ···························· 4-26 · FK-088 (CONTROL SWITCH) SCHEMATIC DIAGRAM ···························· 4-27 · MI-050 (MIC IN), FT-092 (REMOTE) SCHEMATIC DIAGRAM ···························· 4-29 · FP-893, FP-894 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-30 · LB-100 (BACK LIGHT) SCHEMATIC DIAGRAM ···························· 4-31 · CONTROL SWITCH BLOCK (CF-4980, PS-4980) SCHEMATIC DIAGRAM ···························· 4-32 · HL-013 (LCD DRIVE) SCHEMATIC DIAGRAM ···························· 4-33 · FP-195, FP-196, FP-205 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-33 · MA-430 (AUDIO AMP) SCHEMATIC DIAGRAM ···························· 4-35 · DD-216 (1/2) (DC/DC CONVERTER) SCHEMATIC DIAGRAM ···························· 4-37 · DD-216 (2/2) (DC REGURATOR) SCHEMATIC DIAGRAM ···························· 4-39 · RM-091 (REAR REMOCON RECEIVER) SCHEMATIC DIAGRAM ···························· 4-41 Schematic diagrams of the FP-594 and VC-358 board are not shown. Pages from 4-43 to 4-78 are not shown. 4-3. PRINTED WIRING BOARDS ····································· 4-81 · CD-512 (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-81 · JK-267 (JACK BOARD) PRINTED WIRING BOARD ······················· 4-83 · CK-140 (KEY IN) PRINTED WIRING BOARD ······················· 4-85 · PD-217 (RGB DRIVE, TG) PRINTED WIRING BOARD ······················· 4-87 · FP-194 FLEXIBLE PRINTED WIRING BOARD ······················· 4-88 · LA-028 (ZOOM/FOCUS DRIVE, VAP DRIVE, KEY IN/CONNECTOR) PRINTED WIRING BOARD ······················· 4-89 · SE-147 (VAP SENSOR) PRINTED WIRING BOARD ······················· 4-91 · FP-188 FLEXIBLE PRINTED WIRING BOARD ······················· 4-91 · FP-189 FLEXIBLE PRINTED WIRING BOARD ······················· 4-92 · MS-209 (MS CONNECTOR) PRINTED WIRING BOARD ······················· 4-93 · KP-013 (SELECT DIAL) PRINTED WIRING BOARD ······················· 4-95
3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/4) ··························· 3-1 OVERALL BLOCK DIAGRAM (2/4) ··························· 3-3 OVERALL BLOCK DIAGRAM (3/4) ··························· 3-5 OVERALL BLOCK DIAGRAM (4/4) ··························· 3-7 POWER BLOCK DIAGRAM (1/3) ································ 3-9 POWER BLOCK DIAGRAM (2/3) ······························ 3-11 POWER BLOCK DIAGRAM (3/3) ······························ 3-13
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3) ······················· 4-1 FRAME SCHEMATIC DIAGRAM (2/3) ······················· 4-3 FRAME SCHEMATIC DIAGRAM (3/3) ······················· 4-5 4-2. SCHEMATIC DIAGRAMS ·········································· 4-11 · CD-512 (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-11 · JK-267 (JACK BOARD) SCHEMATIC DIAGRAM ···························· 4-13 · CK-140 (KEY IN) SCHEMATIC DIAGRAM ···························· 4-15 · CONTROL SWITCH BLOCK (ED-4980) SCHEMATIC DIAGRAM ···························· 4-16 · FP-194, FP-197 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-16 · PD-217 (RGB DRIVE, TG) SCHEMATIC DIAGRAM ···························· 4-17
--4--
DCR-VX2100/VX2100E
· MK-016 (CONTROL KEY) PRINTED WIRING BOARD ······················· 4-95 · FK-088 (CONTROL SWITCH) PRINTED WIRING BOARD ······················· 4-97 · MI-050 (MIC IN) PRINTED WIRING BOARD ······················· 4-99 · FT-092 (REMOTE) PRINTED WIRING BOARD ······················· 4-99 · LB-100 (BACK LIGHT) PRINTED WIRING BOARD ····················· 4-101 · HL-013 (LCD DRIVE) PRINTED WIRING BOARD ····················· 4-103 · FP-196 FLEXIBLE PRINTED WIRING BOARD ····················· 4-104 · MA-430 (AUDIO AMP) PRINTED WIRING BOARD ····················· 4-105 · DD-216 (DC/DC CONVERTER, DC REGURATOR) PRINTED WIRING BOARD ····················· 4-107 · ZM-030 (ZOOM SWITCH) PRINTED WIRING BOARD ····················· 4-109 · RM-091 (REAR REMOCON RECEIVER) PRINTED WIRING BOARD ····················· 4-111 Printed wiring boards of the FP-594 and VC-358 board are not shown. Pages from 4-113 to 4-118 are not shown. 4-4. WAVEFORMS ···························································· 4-119 Waveforms of the VC-358 board are not shown. Pages 4-121 to 4-123 are not shown. 4-5. MOUNTED PARTS LOCATION ······························· 4-124 Mounted parts locations of the VC-358 board are not shown. Page 4-127 to 4-128 are not shown.
5.
REPAIR PARTS LIST
5-1. EXPLODED VIEWS ······················································ 5-3 5-1-1. OVERALL SECTION-1 ················································· 5-3 5-1-2. OVERALL SECTION-2 ················································· 5-4 5-1-3. CABINET (L) SECTION ················································ 5-5 5-1-4. CABINET (R) SECTION-1 ············································ 5-6 5-1-5. CABINET (R) SECTION-2 ············································ 5-7 5-1-6. UPPER HANDLE SECTION ········································· 5-8 5-1-7. BATTERY PANEL SECTION ········································ 5-9 5-1-8. EVF SECTION ······························································ 5-10 5-1-9. CENTER FRAME SECTION ······································· 5-11 5-1-10. LENS BLOCK SECTION ·········································· 5-12 5-1-11. CASSETTE COMPARTMENT, DRUM AND REEL TABLE ASSEMBLY ····················································· 5-13 5-1-12. TAPE GUIDE, PINCH SLIDER ASSEMBLY AND BRAKE SLIDER ASSEMBLY ····································· 5-14 5-1-13. EACH GEARS AND LOADING/CAPSTAN MOTOR ASSEMBLY ·································································· 5-15 5-2. ELECTRICAL PARTS LIST ········································ 5-16 Parts list of the VC-358 board is not shown. Pages from 5-27 to 5-35 are not shown.
--5--
DCR-VX2100/VX2100E SECTION 1 SERVICE NOTE
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire.
Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside)
1-1
DCR-VX2100/VX2100E
1-2. SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the "ADJ" side. Method 2. Use the DC IN terminal. (Use the AC power adaptor. (AC-L10, AC-VQ800 etc. ))
2.
1 2 3 4 5 6
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
Refer to page 2-3 to remove the upper handle block assembly. Refer to page 2-6 to remove the cabinet (L) assembly. Refer to page 2-6 to remove the mechanism deck (Including VC-358 board and DD-216 board). Remove DD-216 board from the mechanism deck (Including VC-358 board). Remove the CN022 (27P 0.3 mm) of VC-358 board. Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
DC power supply (+4.5V)
: loading : unloading
Disconnect from CN022 (27P) of VC-358 board.
Loading motor
1-2
DCR-VX2100/VX2100E
1-3. SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTION
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen or LCD window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
Viewfinder or LCD screen
C:31:11
2.
SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the counter of the viewfinder, LCD screen or LCD window consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
LCD window
C : 3 1 : 11
Blinks at 3.2Hz
C
Repaired by: C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
31
Block
11
Detailed Code
Refer to Indicates the appropriate "Self-diagnosis Code Table". step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
Note: The "self-diagnosis display" data will be backed up by the coin-type lithium battery of ZM-030 board BT801, 802. When the (upper) handle block is removed, the "self-diagnosis display" data will be lost by initialization.
1-3
DCR-VX2100/VX2100E
3.
Repaired by:
SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code Block Detailed Function Code 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4 0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2 Symptom/State Correction
C C C C C C C C C C C C C C C C C C C C C C C
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations Difficult to adjust focus (Cannot initialize focus.)
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin wg of LA-028 board) when focusing is performed when the focus ring is rotated in the focus manual mode, and the focus motor drive circuit (IC140 of LA-028 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ws of LA-028 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC140 of LA-028 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE601 of SE-147 board) peripheral circuits. Inspect yaw angular velocity sensor (SE600 of SE-147 board) peripheral circuits.
E
6
1
0
0
E
6
1
1
0
Zoom operations fault (Cannot initialize zoom lens.) Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)
E
6
2
0
0
E
6
2
0
1
1-4E
DCR-VX2100/VX2100E SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. LCD section (HL-013, PD-217 boards, Inverter transformer unit) HL-013, PD-217 boards service position
2-2. EVF section (LB-100 board)
LB-100 board service position
2-3. (Upper) handle block assembly
2-4. FK-080, MA-430, MI-050, FT-092, RM-091, ZM-030 boards FK-080, MA-430, MI-050, FT-092, RM-091 boards service position
2-5. Cabinet (L) block assembly, Mechanism deck, VC-358, DD-216, JK-267 boards (for force eject of cassette and VTR section check) 2-13. Control switch block (PS-4980), Control switch block (CF-4980)
Mechanism deck service position-1
Service position to check the VTR section
DCR-VX2100/VX2100E
2-6. Cabinet (R) block assembly
CK-140 board service position
2-7. Cabinet bottom assembly
2-14. CK-140 board
2-8. Battery panel block assembly (MK-016, KP-013, MS-209 boards)
2-15. Control switch block (ED-4980), Hinge assembly
2-9. EVF block assembly
2-10. LA-028, DD-216, VC-358, JK-267 boards, Mechanism deck
2-11. Lens block assembly, Center frame assembly
Service position to check the camera section
2-12. CD-512, SE-147 boards, Zoom lens assembly
[Connection diagram for service position (Mainly for voltage measurement and check)] (CK-140, VC-358, JK-267, CD-512, DD-216, LA-028, KP-013, MK-016, MS-209 boards, Mechanism deck-2)
2-1
DCR-VX2100/VX2100E
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD SECTION (HL-013, PD-217 BOARDS, INVERTER TRANSFORMER UNIT)
REMOVING THE PD-217 BOARD, INVERTER TRANSFORMER UNIT
4 Harness (CP-093) (8P) 6 LCD frame, BL retainer, FP-196 flexible board 5 Harness (CP-094) (14P) qa Remove the three solderings qh Inverter transformer unit 1 FP-195 flexible board (7P)
7 -21 PD oard B
2 Two screws (M2 × 3), lock ace
3 P cabinet (C) assembly
q; HL-013 board 9 Release the two claws and slide the HL-013 board in the direction of the arrow B. qs Two screws (M2 × 3), lock ace qd Panel holder 7 Release the two claws and slide the indication panel block assembly in the direction of the arrow A. A 8 Indication panel block assembly 6 FP-205 flexible board (21P)
B
qa Screw (M2 × 3), lock ace
q; Screw (M1.7 × 2.5), lock ace qj PD-217 board
qd PCB clip
qf PCB clip qg Remove the six solderings 7 Two screws (M1.7 × 2.5), lock ace qs Back light Cold cathode fluorescent tube 9 Liquid crystal indicator module (24P) 8 P cabinet (M) assembly 2 Two screws (M2 × 5), lock ace 3 Three claws
5 FP-196 flexible board (5P)
7 -21 PD oard B
1 Two screws (M2 × 5), lock ace 4 FP-195 flexible board (7P)
[HL-013, PD-217 BOARDS SERVICE POSITION]
HL-013 board Indication panel block assembly (21P) Adjustment remote commander (RM-95) 1 LANC jack CN007 20
2 Claw
FP-196 flexible board (5P)
7 -21 PD oard B
FP-195 flexible board (7P) PD-217 board Inverter transformer unit AC POWER ADAPTOR
3 CPC cover
CPC-13 jig (J-6082-443-A) AC IN
1 Screw (M2 × 5), lock ace
2-2
DCR-VX2100/VX2100E
2-2. EVF SECTION (LB-100 BOARD)
2 EVF rear cabinet assembly 4 EVF front cabinet (upper)
B
A
1 Push the lock knob in the direction of the arrow A and remove the EVF rear cabinet assembly in the direction of the arrow B.
6
3 Two tapping screws (M1.7 × 8)
REMOVING THE LB-100 BOARD
2 LCD (LCX033ANA-1)(16P) 9 LCD (LCX033ANA-1) 4 Two claws 1 FP-193 flexible board (27P) 5 EVF front cabinet (lower) assembly qs LCD holder assembly
3 Two claws qa LCD cushion q; Light interception sheet 8 Prism sheet 7 Illuminator 5 Lamp guide (20)
6 LB-100 board
[LB-100 BOARD SERVICE POSITION]
Adjustment remote commander (RM-95)
LCD holder assembly LB-100 board CPC-13 jig (J-6082-443-A) AC POWER ADAPTOR AC IN
LANC jack
2-3. (UPPER) HANDLE BLOCK ASSEMBLY
4 Tilt up the finder. 9 (Upper) handle block assembly 6 Tilt down the finder.
2 Two screws (M2 × 5), lock ace 3 Screw (M2 × 5), lock ace 1 Two screws (M2 × 5), lock ace
7 8 FP-895 flexible board (40P)
5 Screw (M2 × 5), lock ace
2-3
DCR-VX2100/VX2100E
2-4. FK-088, MA-430, MI-050, FT-092, RM-091, ZM-030 BOARDS
1 Three screws (M2 × 5), lock ace 1 RM-091 board (21P) 5 Handle cover assembly 7 ZM-030 board 3 MA-430 board (23P) 3 Four tapping screws (B2 × 5) 9 Cabinet (upper) 5 Three screws (M2 × 5), spring bolt 8 FK frame assembly 4 Ferrite core qd FP-896 flexible board (15P) qg FP-893 flexible board (20P) 6 RM-091 board (7P) 8 Tapping screw (B2 × 5) qa RM-091 board 9 Two claws q; RM fixed holder assembly 4 Tapping screw (B2 × 5) qs Screw (M2 × 3), lock ace
qh MA-430 board 2 Cap (ST)
2 Sheet 7 FK-088 board 6 Four screws (M2 × 3), spring bolt qk Two claws
qf FP-894 flexible board (15P) qj Screw (M2 × 5), lock ace ql Microphone cabinet (L)
3 Outer connector (hot shoe), Strap sheet metal, FP-896 flexible board
1 Two screws (M2 × 5), lock ace 4 Microphon sheet 8 Handle assembly
7 Screw (M2 × 5), lock ace q; Nut (M6 × 0.5) qs Microphone cabinet (R) assembly, Microphone terminal bracket, Microphone knob 5 Remove it in the direction of the arrow A. A 6 Screw (M2 × 5), lock ace
2 Screw (M2 × 5), lock ace
9 Screw (M2 × 3), lock ace qa FP-893 flexible board
REMOVING THE MI-050, FT-092 BOARDS
9 Microphone case 1 Two tapping screws (B2 × 5) 7 Four claws 4 Claw 3 Rubber neck assembly
5 Microphone cover 8 Microphone unit (R) qs FP-894 flexible board, MI-050 board, FT-092 board
2 Tapping screw (B2 × 5)
q; Microphone unit (L) 6 Microphone mask assembly
qa Microphone case
2-4
DCR-VX2100/VX2100E
[FK-088, MA-430, MI-050, FT-092, RM-091 BOARDS SERVICE POSITION]
ZM-030 board RM-091 board
FP-894 flexible board (15P) MI-050 board Microphone unit (R)
MA-430 board
CPC-13 jig (J-6082-443-A) FT-092 board FP-893 flexible board FK-088 board
Microphone unit (L) Adjustment remote commander (RM-95)
AC POWER ADAPTOR LANC jack
AC IN
2-5
DCR-VX2100/VX2100E
2-5. CABINET (L) BLOCK ASSEMBLY, MECHANISM DECK, VC-358, DD-216, JK-267 BOARDS (FOR FORCE EJECT OF CASSETTE AND VTR SECTION CHECK)
3 Screw (M2 × 5), spring bolt 6 Cabinet (L) block assembly
(FOR FORCE EJECT OF CASSETTE)
4 Screw (M2 × 3), lock ace 5 Flexible retainer 2 FP-895 flexible board (13P) 1 FP-193 flexible board (27P) q; Claw 8 JK-267 board (40P)
1 Screw (M2 × 5), lock ace 2 Screw (M2 × 5), spring bolt 5 Three screws (M2 × 5), spring bolt 4 Two screws (M2 × 3), spring bolt
3 Screw (M2 × 3), lock ace 6 FP-187 flexible board (50P)
9 Four screws (M2 × 3), EG grip 7 FP-186 flexible board (80P) qa CD-512 board (50P)
qd DC-IN connector (3P) qs Battery terminal board (4P)
qf Mechanism deck, VC-358, DD-216 board, MD frame assembly
(FOR VTR SECTION CHECK)
6 Mechanism deck, VC-358 board, MD frame assembly 4 FP-191 flexible board (60P)
5 -3 VCard o B 8
1 Two screws (M2 × 5), spring bolt
DD 6 21
3 Two screws (M2 × 3), lock ace 5 DD-216 board
2 JK-267 board, JK frame
2-6
DCR-VX2100/VX2100E
[MECHANISM DECK SERVICE POSITION-1]
Note: Use the parts only which can be removed easily from outside of the mechanism deck.
Adjustment remote commander (RM-95)
Mechanism deck
CPC-13 jig (J-6082-443-A)
AC POWER ADAPTOR
AC IN
Cabinet (L) block assembly
[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
To check the VTR Section, set the VTR to the "forced VTR power ON" mode. Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position) (However, connect the cabinet (L) assembly when cassette is going to be ejected only.) Setting the "Forced VTR Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 02, and press the PAUSE button of the adjustment remote commander. Exiting the "Forced VTR Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.
AC IN
AC POWER ADAPTOR
DD-216 board DC-IN connector (3P) (1-794-637-11)
FP-191 flexible board (60P) Insert the FP-191 flexible board in the opposite direction to the normal insertion direction.
CPC-13 jig (J-6082-443-A) Connect here when the tape path check is going to be performed.
V B Co 3 a 5 rd 8
VC-358 board
JK-267 board
Mechanism deck
LANC jack
VIDEO jack
Monitor TV
Cabinet (L) block assembly
Adjustment remote commander (RM-95) Control switch block (CF-4980) (14P) (Connect here when cassette is going to be ejected.)
2-7
DCR-VX2100/VX2100E
2-6. CABINET (R) BLOCK ASSEMBLY
5 Screw (M2 × 5), spring bolt
7 Cabinet (R) block assembly 6 Two screws (M2 × 5), spring bolt 1 Screw (M2 × 5), spring bolt
4 Two screws (M2 × 5), spring bolt
3 CF ornamental plate 2 Claw
[CK-140 BOARD SERVICE POSITION]
CPC-13 jig (J-6082-443-A)
Adjustment remote commander (RM-95) AC POWER ADAPTOR LANC jack
C Bo K-1 ar 40 d
AC IN
CK-140 board Cabinet (R) block assembly
2-7. CABINET BOTTOM ASSEMBLY
REMOVING THE FBS COVER
1 Two tapping screws (B2 × 5) 3 Two tapping screws (B2 × 5)
1 FP-189 flexible board (6P)
5 Cabinet bottom assembly
2 FP-189 flexible board
5 FBS cover
3 Tripod table
4 Two screws (M2 × 5), lock ace 2 Four screws (M2 × 5), lock ace
4 Cabinet (bottom)
2-8
DCR-VX2100/VX2100E
2-8. BATTERY PANEL BLOCK ASSEMBLY (MK-016, KP-013, MS-209 BOARDS)
9 CPC cover q; Battery panel block assembly 8 Screw (M2 × 5), lock ace 7 Two screws (M2 × 5), lock ace 6 Two screws (M2 × 5), lock ace
4 Screw (M2 × 3), lock ace
2 -0 LAard o b 8
1 FP-190 flexible board (20P) 5 Screw (M2 × 5), lock ace 2 DC-IN connector (3P) 3 Battery terminal board (4P)
qs DC-IN connector qa DC jack retainer q; Two tapping screws (B2 × 5) 9 MS holder assembly 8 Two tapping screws (B2 × 5) A
PRECAUTION DURING INSTALLATION
When installing it, align the switch position as shown.
09 -2 MS rd oa B
3 MK-016 board 2 MK retainer A 1 Two tapping screws (B2 × 5) 5 KP-013 board 4 Screw (M2 × 3), lock ace
7 MS-209 board
6 Two screws (M2 × 3), lock ace
2-9. EVF BLOCK ASSEMBLY
6 Two screws (M2 × 3), lock ace 1 FP-193 flexible board (27P) 7 EVF block assembly
4 Peel off the area shown by shading. 3 Claw 2 Screw (M2 × 3), lock ace 5 Flexible clamp
28 -0 LAard bo
2-9
DCR-VX2100/VX2100E
2-10.LA-028, DD-216, VC-358, JK-267 BOARDS, MECHANISM DECK
1 Screw (M2 × 3), lock ace 2 Flexible retainer 9 LA joint 3 FP-188 flexible board (6P) 7 LA-028 board
28 -0 LA rd a Bo
8 Screw (M2 × 3), lock ace
6 Three screws (M2 × 3), lock ace
5 Flexible board (27P) (from VAP assembly) 4 Flexible board (39P) (from zoom lens assembly)
1 CD-512 board (50P)
8 -02 LABoard
4 Two screws (M2 × 5), spring bolt 5 3 Two screws (M2 × 3), EG grip 2 Two screws (M2 × 3), EG grip
8 Two screws (M2 × 2), lock ace
9 LD outer lid 7 MD frame assembly
4 VC-358 board q; Mechanism deck A CB D 5 Two step screws (M2) DB qa Two screws C (M2 × 3), lock ace A 3 Three screws (M2 × 3), lock ace 1 Two screws (M2 × 3), lock ace
6 Step screw (M2) qg JK-267 board qs Two screws (M2 × 3), lock ace qd Two claws
58 -3 VCard Bo
DD 6 21
(LA-028 board)
2 -0 LAard Bo 8
2 DD-216 board
qf JK frame
2-10
DCR-VX2100/VX2100E
2-11.LENS BLOCK ASSEMBLY, CENTER FRAME ASSEMBLY
qd Center frame assembly 6 Screw (M2 × 3), lock ace qs FP-188 flexible board (6P) q; Two screws (M2 × 4), lock ace qa Two screws (M2 × 3), lock ace
9 Lens block assembly PRECAUTION DURING INSTALLATION
When installing it. Align the swich position. FP-188 flexible board
8 Two screws (M2 × 5), EG grip 7 Two screws (M2 × 5), EG grip 2 Tapping screw (B2 × 5) 1 Screw (M2 × 3), lock ace 3 CCD cover
Lens block assembly
Center frame assembly
4 Screw (M2 × 3), lock ace 5 CJ-064 harness
[SERVICE POSITION TO CHECK THE CAMERA SECTION]
Connection to Check the CAMERA Section
To check the CAMERA Section, set the CAMERA to the "forced CAMERA power ON" mode. Setting the "Forced CAMERA Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. Exiting the "Forced CAMERA Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.
FP-191 flexible board (60P) Insert the FP-191 flexible board in the opposite direction to the normal insertion direction. AC IN AC POWER ADAPTOR DD-216 board
FP-186 flexible board (80P) Insert the FP-186 flexible board in the opposite direction to the normal insertion direction. CD-512 board (50P) Flexible board (27P) (from VAP assembly)
8 2 -0 d A r L oa B
DC-IN connector (3P) (1-794-637-21) Extension cable (J-6082-496-A) (50P)
LA-028 board VC-358 board JK-267 board Lens block assembly
V B Co 3 a 5 rd 8
Flexible board (39P) (from zoom lens assembly) Mechanism deck Monitor TV LANC jack VIDEO jack
Adjustment remote commander (RM-95)
2-11
DCR-VX2100/VX2100E
2-12.CD-512, SE-147 BOARDS, ZOOM LENS ASSEMBLY
4 Three tapping screws (B2 × 5) 5 SE-147 board 3 Flexible board (6P) (from zoom lens assembly) 9 Zoom lens (VCL-6012WB) 1 Three tapping screws (M1.7 × 7)
2 (CCD) flexible block assembly
REMOVING THE CD-512 BOARD
8 Remove the soldering. 7 Sheet (CD) 9 CJ-064 harness 3 Remove the sixteen solderings. q; CD-512 board 4 Remove the sixteen solderings. 5 Remove the sixteen solderings. 2 Prism cover 1 CCD heat sink
6 CCD emblem 7 Rubber foot (A) 8 Name ring 6 Prism assembly
REMOVING THE ZOOM LENS ASSEMBLY
4 Ornamental ring assembly Rotate it in the direction of the arrow C and remove it in the direction of the arrow D. B A 3 Zoom lens assembly Rotate it in the direction of the arrow A and remove it in the direction of the arrow B. 1 Tapping screw (M1.7 × 4) 5 VAP assembly
2 Two tapping screws (B2 × 7)
C D
2-13.CONTROL SWITCH BLOCK (PS-4980), CONTROL SWITCH BLOCK (CF-4980)
5 Control switch block (PS-4980) 3 Control switch block (CF-4980) 1 Tapping screw (B2 × 5) 4 Two tapping screws (B2 × 5) 2 Control switch block (PS-4980) (8P) 7 Four tapping screws (B2 × 5) 8 Slider assembly PRECAUTION DURING INSTALLATION Install the slider assembly while pushing the eject lever fully to the left (CCW). 6 Push the eject knob in the direction of the arrow, and open the cassette lid.
Cassette lid Eject knob
q; Control switch block (CF-4980) Be careful not to damage the control switch block's (CF-4980) flexible.
9 Two tapping screws (B2 × 5)
Eject lever
2-12
DCR-VX2100/VX2100E
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)] CK-140, VC-358, JK-267, CD-512, DD-216, LA-028, KP-013, MK-016, MS-209 BOARDS, MECHANISM DECK-2
AC IN CPC-13 jig (J-6082-443-A) KP-013 board MK-016 board AC POWER ADAPTOR DC-IN connector (3P) (1-794-637-21) Battery panel assembly
Battery terminal board (4P) DD-216 board
B A
Mechanism deck
A B
MS-209 board Control switch block (PS-4980) (8P) LA-028 board
LA Bo-02 ar 8 d
Flexible board (27P) (from VAP assembly) Flexible board (39P) from zoom lens assembly
Control switch block (CF-4980) (14P) JK-267 board EVF block assembly Adjustment remote commander (RM-95) FP-193 flexible board (27P) CK-140 board Cabinet (R) block assembly VC-358 board FP-187 flexible board (50P) Lens block assembly CD-512 board (50P) Extension cable (J-6082-496-A) (50P)
2-14.CK-140 BOARD
PRECAUTION DURING INSTALLATION
V B Co 3 a 5 rd 8
When installing it. Align the switch position.
qa Claw 9 FP-194 flexible board (5P) qf CK-140 board
q; Seven screws (M2 × 3), lock ace
qd Harness (CP-094) (14P) qs Harness (CP-093) (8P) 3 R flexible protection sheet 5 Two screws (M2 × 3), lock ace 6 SP retainer plate assembly 2 FP-197 flexible board (6P) 1 Control switch block (ED-4980) (6P) 8 Speaker holder 4 Speaker (2P) 7 Speaker
2-13
DCR-VX2100/VX2100E
2-15.CONTROL SWITCH BLOCK (ED-4980), HINGE ASSEMBLY
Start the removal work after the LCD section has been removed referring section 2-1.
2 Control switch block (ED-4980) 1 Bright button
3 Blind door (D) assembly 2 Hinge lid 1 Three screws (M2 × 3), lock ace 8 Three screws (M2 × 5), spring bolt 9
q; Screw (M1.7 × 2.5), lock ace qs Hinge assembly A
2 Screw (M1.7 × 2.5), 3 Three claws lock ace
4 Hinge cover (rear) 6 Two harness fixed tapes
7 6 Three screws (M2 × 3), spring bolt 4 Harness (CP-093) (8P) 5 Harness (CP-094) (14P)
qa FP-197 flexible board 9 Screw (M1.7 × 2.5), lock ace 5 Hinge cover (front)
A
1 Two screws (M1.7 × 2.5), lock ace
7 Harness (CP-093)
8 Harness (CP-094)
2-14
DCR-VX2100/VX2100E
2-16.CIRCUIT BOARDS LOCATION
The circuit boards contained in the zoom lens are not shown.
MI-050 (MIC IN)
LB-100 MA-430 (BACK LIGHT) (AUDIO AMP)
CK-140 (KEY IN)
FT-092 (REMOTE)
PD-217 (RGB DRIVE, TG)
INVERTER TRANSFORMER UNIT HL-013 (LCD DRIVE) SE-147 (VAP SENSOR) CD-512 (CCD IMAGER) FK-088 (CONTROL SWITCH)
RM-091 (REMOTE SENSOR) ZM-030 (ZOOM SWITCH) JK-267 (JACK BOARD)
LA-028 ZOOM, FOCUS DRIVE, VAP DRIVE, KEY IN/CONNECTOR
MK-016 (CONTROL KEY)
KP-013 (LCD DRIVE) MS-209 (MS CONNECTOR)
DD-216 (DC/DC CONVERTER, DC REGULATOR) VC-358 S/H AGC, TG, CAMERA SIGNAL PROCESS, MS I/F, RS232C I/F, STILL CONTROL, MS DRIVE, DV SIGNAL PROCESS, DV INTERFACE, REC/PB AMP, LINE IN/OUT, LINE A/D, RGB DRIVE/TG, CAMERA CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, HI CONTROL, AU LINE A/D, D/A, LINE AMP, CONNECTOR
2-15
DCR-VX2100/VX2100E
2-17.FLEXIBLE BOARDS LOCATION
The flexible boards contained in the mechanism deck and that in the zoom lens are not shown.
FP-896
FP-193 FP-202 FP-893 FP-895
FP-894 FP-190
FP-194
FP-196 FP-189 FP-195 FP-191 FP-188 CONTROL SWITCH BLOCK (ED-4980)
CONTROL SWITCH BLOCK (PS-4980)
FP-186
FP-187 FP-205
FP-197
CONTROL SWITCH BLOCK (CF-4980)
2-16E
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/4) OVERALL BLOCK DIAGRAM (2/4) OVERALL BLOCK DIAGRAM (3/4) OVERALL BLOCK DIAGRAM (4/4) POWER BLOCK DIAGRAM (1/3) POWER BLOCK DIAGRAM (2/3) POWER BLOCK DIAGRAM (3/3)
DCR-VX2100/VX2100E SECTION 3 BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/4)
CD-512 BOARD IC103 IC101
G-CH CCD IMAGER 8 3 1 35 35 31 32 11,14-16 1-4 V1,V2A,V2B,V3 40 40 43 43 44 44 H1,H2,RG,SUB 29 47 47 DICHROIC PRISM 5 R 21 CN025 G CCD OUT 40 42 1 3 G 38 47 G D0-09 2 11
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-358 BOARD(1/4)
AGC CONT 1,2 R,B GAIN R,G,B OFFSET
(1/18)
7
19
(1/18)
(2/18)
(IC705)SPCK 38 Y0-Y7 45
IC704
S/H,AGC 28
IC706
A/D CONVERTER 26 36 R D0-09 79 88
IC771
CAMERA SIGNAL PROCESS
LENS BLOCK
29 C0-C7 36 49 HD,VD,OE
1
TO OVERALL BLOCK DIAGRAM (2/4)
IC104 IC102
R-CH CCD IMAGER 8 R CCD OUT 3 1 19 19
IRIS
11 35 34 B 1 48 26 25 19 28 28 29 29 H1,H2,RG,SUB 32 32 XSHD XSHP XRS 11 14 37 38 44 CLPDM PBLK CLP OB 48 1 2 14
B D0-09
50 99 51 90 HI SO,SI,SCK
(SEE PAGE 3-3)
9
17
11,14-16
1-4 V1,V2A,V2B,V3
25 25
IC105 IC100
B-CH CCD IMAGER 8 B CCD OUT 3 1 9 9 31 X701 27MHz H1,H2,RG 6 H1,H2,RG,SUB 18 18 SUB CN100 V1,V2A,V2B,V3 6 45 13 13 29 46 71 HD,VD 70 32 11,14-16 1-4 V1,V2A,V2B,V3 17 3 3
IC705
TIMING GENERATOR 47 SPCK 47 77
(1/18)
IC701,702
CCD V DRIVE
10 5 9
39 38
(1/18)
IRIS METER
M H
ZOOM RESET SENSOR
DRIVE20 8 HALL17 5 ZM RST SENS 22 1
IC141
54 IRIS DRIVE 10 53 HALL AMP 7 41 42
IRIS PWM
HALL AD EN1 DIR 1A,1B 61 63 62 64 66 68 EN1 DIR 1A,1B 62 63 64
ZOOM MOTOR
M M
2 4 6 34
ZOOM A,B
ZOOM MOTOR DRIVE
65 67
EN0 DIR 0A,0B
59 60 61
IC140
FOCUS A,B FOCUS MOTOR DRIVE
64 FOCUS MOTOR 36 38 39 FC RST SENS FOCUS RESET SENSOR 25 28 ND A,B,C ND FILTER SW 27 29 CN050 55 57 59 53 66 68
63 65 67 60 54 56 58
EN0 DIR 0A,0B
43 66 19 20 17 18 82
(12/18)
AGC CONT1,2 R,B GAIN R,G,B OFFSET
IC803
ZM RST SENS EVR 17 16 FC RST SENS
58 57
IC802
CAMERA CONTROL 33 CAM SO,SI,SCK 35
(12/18)
14 15 66
4 ACTIVE PRISM ACTUATOR
3
2
P Y
21 20
P DRIV A,B
IC070,071 073-076
ACTIVE PRISM ACTUATOR DRIVE
P PWM 56 55
45 64 63 ZM SPD SEL H ZOOM AD
IC801
EEPROM
(12/18)
2
ZM SPD SEL H ZOOM AD ZOOM VR AD TO OVERALL BLOCK DIAGRAM (4/4)
15 14
Y DRIV A,B
Y PWM 58 57
44 48 HI SO,SI,SCK
P OUT 12 Y OUT 22 46 45 44 43
61 60
50 62 ZOOM VR AD
(SEE PAGE 3-7)
25 VAP LOCK 26
VAP LOCK +,-
IC072
VAP LOCK DRIVE
VP LOCK DR 36 35
7
VP LOCK SENS 23 38 37
10
FP-893 (FLEXIBLE)
J001 L MIC/ LINE R 20 20 14 14 7 4 6 7 4 6 5 8 3 9
MI-050 BOARD (1/2)
Q706
MA-430 BOARD (1/2) IC1150
MIC AMP 3 12 L 35 22 1 23
FK-076 BOARD (1/2)
LA-028 BOARD (2/4)
ZOOM RING
3 5
MZ F0,F1 1,2
IC144
8,13 DETECTOR
48 50
47 49
MZ A,B
24 25
MIC L
2 3 CN700
36
27
2
L(CH1) TO OVERALL BLOCK DIAGRAM (2/4) (VC-358)
FOCUS RING
8 9
MF F0,F1 1,2 CN052
IC143
8,13 DETECTOR
S001 47 49 48 50 MF A,B 22 23 MIC
5 8 3 9
Q707
3
MIC R
2 5 3 CN701 CN703 CN1100 10
R
1
14 CN1103
2
22 CN500 CN501
35
26 CN053 CN051
1
R(CH2)
(SEE PAGE 3-3)
X801 20MHz SE601 PITCH SENSOR SE600 YAW SENSOR CN600 YSD OUT 3 10 8 CN050 2 CN051 CN023 45 46 PSD OUT 5 12 12 PITCH/YAW SENSOR AMP YS OUT
40 41
LINE
12 12 11 11 ATT 2 2
L
33
IC200
18
PS OUT 43 44
10 10 59 CN101 1 1 CN1101
36 R 3 48 CN1102
11
SHOE MIC L
INTELLIGENT ACCESSORY SHOE(2/2)
58
16
SE-147 BOARD
AUDIO SIGNAL VIDEO SIGNAL
LA-028 BOARD(1/4)
3-1
3-2
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
3-2. OVERALL BLOCK DIAGRAM (2/4)
VC-358 BOARD(2/4)
(3/18)
SPCK SPCK
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN300
DV
Interface
(6/18)
199 77 203 | Y0-Y7 207 211 215 3 7 17 HD,VD OE 62 21 23 200 202 206 212 216 6 8 213 68 1 | C0-C3 5 64 63 DV SIGNAL PROCESS 205 201
138 139 142 | 145
IC1407
37 60 DIGITAL STILL PROCESS | 51 46
IC301
X301 24.576MHz
(7/18)
45 L BUS 42
CN006 6 9 TPA+,TPB+,6 2 6 2
CN301
70
IC361
DV INTERFACE
YO-Y7
Y0-Y7
1
TO OVERALL BLOCK DIAGRAM (1/4) CO-C7 C0-C7
51 141 152 153 156 133 132 127
TRCK LCK
47 79
29 MC BUS 37
| 38 49
HD,VD,OE
HD,VD,DE
61 48 47 96 204 | 87 214 86 Y0-Y7 208
FRRV,TRRV,TRRT
JK-267 BOARD(1/2)
J301 S VIDEO
(SEE PAGE 3-2)
HI SO,SI,SCK
(9/18)
(10/18)
SPCK 68
JK-267 BOARD (2/2)
DATA TO SFD DATA FROM SFD SFD BCK
IC1301
39 48 42 LINE IN LINE OUT AGC ACC Y C
IC903
A/D CONVERTER 59 Y0-Y7 52 49 C0-C7 42
2 C4-C7 9
4
| 83 80
11 13 15 18
99 97
REC CK REC DT
36 34
2 6
HD,VD,OE 79 22 83 78 24 | 6 6 88 7 82 AFCK SYS CLK(IC1401) AFCK(IC903) SPCK(IC705) 196 48 170 8 | 20 · 19 HD VD 184 · 183 179 MC BUS FRRV,TRRV,TRRT 81 79 PB CK ATF ERR TO OVERALL BLOCK DIAGRAM (3/4) AD DT
C
Y
Y 20 20 C 22 22 17 17
Y
18 26 IC1301 CK 25
38 HD,VD,DE 37
G
G
C V
14 22 28 30 46 7 Y C
5
36 34 63 66
J300 (1/2) V VIDEO
X1301 13.5MHz
10
9
(SEE PAGE 3-5)
(3/18)
20 | 31 1 A0-A8
97 | 106
4
TO OVERALL BLOCK DIAGRAM (4/4)
IC1403
HI SO,SI,SCK 16Mbit DRAM SP+,OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD
IC302
(7/18)
CHARACTER GENERATOR
159 18 · 17 · 16 · 14 COL0 195 | · COL3 194 · 191 · 190 | 161 VSP SO,SI,SCK
129 13 D0-D15 38 111 48 LANC SIG |
PANEL G 75 73 PANEL R PANEL B HD,VD EVF G 67 65 63 Y 55 59 C EVF R EVF B
(SEE PAGE 3-8)
(4/18)
1
3 OSD CS OSD SO OSD SCK
71 105 · 106
IC1404
232C ON J303 LANC SIG/232C RD LANC 35 35 LANC GND/232C TD 37 37 Q111 12 14 9 7 RXD RS232C IF
VSP SO,SCK
141 · 142
12 | 21 4 140 132 143 144 1 JID0-JID7
TXD
J302 26 26 28 28 Q1008,1014 L J300 (2/2) AUDIO R R CN301 9 9 CN006 L 12 12
HP L HP R
(16/18)
64 2
IC1001
AUDIO I/O
(16/18)
8 10 SP+,-
IC1002
D/A CONV. A/D CONV.
VSP SO, SCK
L
54
HI SO,SI SCK
R L R
55 19 51 53 46 49 17 25 23 R L R 16 3 12 2 109 9 8 DATA FROM SFD DATA TO SFD SFD BCK X1401 7.375MHz 77 79 54-52 19 21 2 4 L 15
(4/18)
IC1406
EEPROM DI,CI 1 2
SPCK1(IC705)
6
(4/18)
(17/18)
(17/18)
IC1092
3
L(CH1) TO OVERALL BLOCK DIAGRAM (1/4) (LA-028) 1 10 8 3
IC1008
1 58
IC1412
SYSCLK 27 88
(3/18)
(4/18)
112
SHUTTER SOUND
4
IC1401
DIGITAL STILL CONTROL 50 51 TXD RXD
IC1005
EVR
14 13 JID0-JID7
34 41
IC1409
JPEG 2,9-16 58-64 18
IC1408
16Mbit DRAM 1-13 38-48
(5/18)
ATT R(CH2) 2 CN023 7 12 13 14 VSP SO,SCK 15 KASHAON 5 5 7 60
(17/18)
SYSCLK(IC1401) 5-15 55-75 20-31
(SEE PAGE 3-2)
28 36
A0-A10
| 38
(5/18)
4
IC1410
MEMORY STICK I/F 15 | DIO SCLK BS CN023 31 30 33 31 30 33
MS-209 BOARD
CN051 18 20 17 CN056 6 8 5 CN776 CN775 4 8 2
10 | D0-D15 1 · 48 X1411 20MHz 2 4 XTAL OSC SCK | 17 40
MEMORY STICK SLOT
VSP SO,SCK
IC1411
(5/18)
13
16
LA-028 BOARD(3/4)
AUDIO SIGNAL VIDEO SIGNAL VIDEO/AUDIO SIGNAL
3-3
3-4
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
3-3. OVERALL BLOCK DIAGRAM (3/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN007 FOR ADJUSTMENTS 3 2 RF MON
C MECHA DECK
(SEE PAGE 4-39) (8/18)
REC CK REC DT
VC-358 BOARD(3/4)
REC CK REC DT
SWP
IC102
40 42 REC/PB AMP 6 7 2 1 EVEN CN101 ODD 5 6 DRUM 8 9
(8/18)
AD DT 6 AD DT 6 20 15
42
PB Y OUT
27
IC101
EQ A/D CONV. PLL 34 22 24 31
5
TO OVERALL BLOCK DIAGRAM (2/4)
PB CK
PB CK
13
ATF ERR
(SEE PAGE 3-4)
95 60 78 | DRP SO,XDRP SCK SWP
SWP
MC BUS FRRV TRRT,TRRV
(13/18)
80
CN024 CAP FG CAP ON,CAP FWD 2,3 32 14,15 24
M902
IC501
MECHA CONTROL
115 45 46
CAPSTAN FG AMP
CAPSTAN 25 FG
VSP SO,SI,SCK
(13/18)
26 | 37 FRRV TRRT TRRV 106 | 108 74 | 76 68 DRUM PWM 53 52 47 48 LPF 1 DRUM ERROR 22 58 LPF PWM DRIVE 69 CAP PWM 56
IC402
(14/18)
CAPSTAN MOTOR DRIVE 21,23,19
17 | 20 7 | 10 11 | 14 CN020 M901 6 | 1
IC502
EEPROM 2-4
(14/18)
CN021 CN450 CAP ERROR 18
(1/2)
Q319 CN450 CN021 CAP VS 40 39 18.22
M
CAPSTAN MOTOR
IC401
(2/2)
54 45 46
IC300
(2/2)
SWITCHING 61
Q320 DRUM VS SWITCHING 38 37 11
IC401
(14/18)
(1/2) DRUM MOTOR DRIVE
20,22,24
M
DRUM MOTOR
DD-216 BOARD(1/2)
47 DRUM ON,DRUM FWD,DRUM START 48 63 DRUM FG 1 16,6,3
X501 20MHz
2
10
DRUM FG
83
11
DRUM PG
6
TO OVERALL BLOCK DIAGRAM (4/4)
HI SO,SI,SCK
82 81
116 CHIME SDA,CHIME SCK,CHIME VDD XCC DOWN 117
DRUM FG AMP
64
(SEE PAGE 3-8)
DRUM PG
59 DRUM PG AMP
61 CN022 27 M903 LOADING MOTOR
49 50
LOAD,UNLOAD
26,25
LOADING MOTOR DRIVE
28,30
| 24
M
DEW SENSOR
114 113
TREEL FG SREEL FG
40 48 REEL FG AMP
42,43 45,46 23
54
TAPE END
34 TAPE END DETECT
35
8 9
T REEL SENSOR
H902
53
TAPE TOP
37 TAPE TOP DETECT
36
12 11
S REEL SENSOR
H901
96
DEW DET 21
Q901 TAPE END SENSOR
55
TAPE LED ON Q902 TAPE TOP SENSOR
44
REC PROOF SW
1
39 | 42
MODE SW A - MODE SW D 14
D901 TAPE LED
REC PROOF 3 5 | 7 XCC DOWN 4 C IN 19 | 16 S903 MODE SWITCH S902 4PIN CONNECTOR CN901 S901
16
VIDEO/AUDIO SIGNAL
3-5
3-6
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
3-4. OVERALL BLOCK DIAGRAM (4/4)
CONTROL SWITCH BLOCK (ED-4980)
EXPOSURE DIAL 1 2 S251,253,261 CN252 EXPOSURE/SW 4 CN255 DISPLAY SW SELF TIMER SW DATA CODE SW KEY AD5 36 36 X1101 20MHz X1102 32.768KHz 98 40 41 52 53 97 S252,254,257,259,262 KEY AD6 4 MEMORY FUNCTION SW 38 38 99 KEY AD6 XCC DOWN S256 RESET HI XRESET RESET 32 32 CN008 CN254 VTR UNREG MENU 2 BATT UNREG BATT LI 3V 3 7 42 5 38 XRESET 18 KEY AD5 20MHz OUT 20MHz IN 32KHz IN 32KHz OUT KEY AD4 CHIME AD2 73 CHIME SDA CHIME SCK CHIME VDD XCC DOWN CHIME SDA CHIME SCL CHIME AD0 5 6 71 HSY 5 PSIG 4 COM 2 VG 1 CN2105 FOR ADJUSTMENTS CN1703
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-358 BOARD(4/4)
(15/18)
CK-140 BOARD(1/2)
CN250 40 40 42 42 DIAL C,D 82 83 DIAL C DIAL D
IC1104
HI CONTROL KEY AD7 100 22 22
CK-140 BOARD(2/2)
CN250 KEY AD7 5 OSD SO,SCK 4 3 6 5 4
HL-013 BOARD
CN1702 1
FP-196
(FLEXIBLE)
VOLUME SW LCD BRIGHT SW 5 S001-004 LCD902
CN1701
IC1701
8 7 LCD DRIVE
11
2
COM1-4 SEG1-16
LCD INDICATOR
30
21
FP-197
(FLEXIBLE)
S002 PANEL OPEN/ CLOSE SW S001 PANEL REVERSE SW 2 CN256
S250,255,258,260,263 ZEBRA SW,TITLE SW, DIGITAL EFECT SW, PICTURE EFECT SW, MEMORY MIX SW KEY AD4 34 34
PD-217 BOARD
6
TO OVERALL BLOCK DIAGRAM (3/4)
20 20 PANEL R,G,B 16 16 18 18
3 2 1
3 2 1
48 47 46
IC2101
RGB DRIVE
20 VR,VG,VB 22 24 27 PSIG
4 5 3 6 COM 23 7 15
LCD901
LCD UNIT
HI SO,SI,SCK
FP-194
(FLEXIBLE)
(SEE PAGE 3-5)
VDD
40 39 29 29 31 31 12
IC1102
VDD SWITCH
6
51 77 87
(15/18)
CN009
HI SO HI SI HI SCK 19 92 16 14 15 20 17 XPHOTO FREEZE KEY AD8 XS/S SW XVTR MODE SW XCAM+STBY SW XPHOTO STBY SW XEJECT SW XCS OSD OSD SO XOSD SCK
33 34 35 XHD 9 9 XVD 11 11 CN251 44 45 41 41 SP+,1 2 CN253 46 43 43 CN008 SP901 SPEAKER 12 12 CN2100 HD OUT 13 13 HI SO,SCK 35 35 37 37 10 8 10 8
46 45 42 1 48
IC2103
TIMING GENERATOR
15
19 22
CONTROL SWITCH BLOCK (CF4980)
ZOOM VR AD ZOOM VR XPHOTO FREEZE PHOTO SW 4 XPHOTO REC 5 XS/S SW START/STOP SW XVTR MODE SW XCAM+STBY SW PHOTO STBY SW 6 7 8 9 XEJECT SW EJECT SW 10 3
24 CN2104
2
4
9 PWM BL ON INVERTER BLOCK ND901 BACK LIGHT
POWER SW
PANEL 4.6V P UNREG
BACK LIGHT DRIVE
START/STOP SW (LOW ANGLE) LID OPEN LID OPEN SW
12
13
31
LID OPEN 48 EVF R,G,B
(11/18)
BATT/EXT SW FAST CHARGE 66 50 29 28 81 14 14 47 46 40 39
LB-100 BOARD
20 22 24 12 35 25 26 24 27 23 3 R,G,B 2 4 COM 1 5 16 12 15 13 14
LCD903 LCD UNIT
IC1802
RGB DRIVE
FP-189
(FLEXIBLE)
2 FADER SW BACK LIGHT SW SPOT LIGHT SW 3 CN054
LA-028 BOARD(4/4)
CN051 KEY AD2 29 KEY AD3 5 24 23 30 95 96 KEY AD2 KEY AD3
VTR DD ON CAM DD ON SHOE ON
3
FP-188
(FLEXIBLE)
S550-552 INDEX SW FOCUS SW 6 CN055 Q1102,1105 1
46 HI SO,SCK 45 42 6 2 CN550 6 EXCUTE(DIAL) 2 CN056 28 27 XVD 25 26 98 DIAL B XHD 1 48 1 S550 SEL/PUSH EXEC DIAL 1 DIAL A,B 27 28 97 DIAL A
(11/18)
IC221
24 PWM 3 25 24 14 4 VR INVERTER BACK LIGHT DRIVE Q221,222
CN201
KP-013 BOARD
IC1803
TIMING GENERATOR
2
8 LED K
14 VG 18 8 7 CN002 CN007 FOR ADJUSTMENTS 20 21 CN200 EVF BL 4.6V VB 13 VCO 15 XHD 12 EVF BL17 EVF BL+
D201 BACK LIGHT
MK-016 BOARD
S001-005 REC LEVEL GAIN SW AUTO WHITE BALANCE SW SHUTTER SW PROGRAM AE SW AUTO LOCK SW CN001 3 10 CN056 INTELLIGENT ACCESSORY SHOE (2/2) 5 6 7
MA-430 BOARD(2/2)
CN1102 5 14 16
FK-088 BOARD(2/2)
LANC SIG 20 32 34 6 18 20 22 9 7 21 10 8
36 MOD 59
MELODY SIRCS ENV
20 80 70 4 HOT SHOE ID1 HOT SHOE ID2 26 XSIRCS IN 24 23 R391,392 93 KEY AD0 KEY AD1 IB SI IB SO LANC IN LANC OUT 1 2 HI,SO,SI,SCK TO OVERALL BLOCK DIAGRAM (2/4) EVF 2.8V EVF 13.5V PANEL R,G,B EVF R,G,B XHD,XVD,SP+,SPOSD,CS,SO,SCK 48 49 25 EVF BL 4.6V
FT-092 BOARD IC750
CN750 REMOTO COMMANDER RECEIVER (FRONT) 1 8 8
MI-050 BOARD(2/2)
S500-511 VTR FUNCTION SW
94
4
(1/2)
DD-216 BOARD(2/2)
PANEL 2.8V PANEL 4.6V PANEL 13.5V D 1.5V D 1.9V A 2.8V AU 2.8V D 2.8V 36 35 TRF 2.8V 38 37 D 3.1V MS 3.1V
IC300
DC/DC CONVERTER
CN702
CN703 14 1
CN1100 SIRCS SIG1 1 18 4 22 24 BATT SIG I/F 19 7 19 20 LANC SIG 11 CN023 10 11 3 ZM SPD SEL 1 2 4 CN004 ZOOM VR AD H ZOOM AD 4 2 1 3 CN501 TO OVERALL BLOCK DIAGRAM (1/4) Q1104
LANC SIG
(SEE PAGE 3-3)
Q700,702,704 7 D751 (IR EMITTER) 7 LED DRIVE SIRCS PWM 13 2 6 CN500 9 S803,804 ZOOM SW S801 ZOOM SPEED SW S802 START/STOP SW 3 2 4 ZM SPD SEL XS/S SW (HAND) 2 LI 4 5 6 CN502 H ZOOM AD 3 1 12 22 8 CN053 20 19
IC1103
LANC I/O
(15/18)
10 12
SHOE UNREG
SHOE ON 34 33 Q339
A 4.6V AU 4.6V
2
P UNREG
RP 4.6V 5 6 5 6 MT 5.2V CAM 12V CAM -7V CAM DD ON 30 32 29 VTR DD ON 31 Q301 CN301 1 2 3 J902 DC IN
(SEE PAGE 3-2)
D1107-1110
IC1102
REMOTE COMMANDER RECEIVER (REAR)
1
49 VTR UNREG 51 11 S1106 CUSTOM PRESET SW 13 CN021 SIRCS SIG BATT UNREG 50 41 46 44
50 52
VTR UNREG CN300 BATT UNREG 1 3 4 FAST CHARGE
BT801,802 LITHIUM BATTERY (SECONDRY)
5 CN801
49 42 BATT/EXT SW 45 BATT SIG 43 CN450
S
J901 BATTERY TERMINAL
16
ZM-030 BOARD
RM-091 BOARD
AUDIO SIGNAL VIDEO SIGNAL
3-7
3-8
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
3-5. POWER BLOCK DIAGRAM (1/3)
DD-216 BOARD
(4-61) Q329, 339 SHOE UNREG 43 INIT CHARGE ON 27 VTR DD ON 31 CAM DD ON CN300 1 BATT UNREG DCPACK SW 29 F300 FAST CHARGE 42 BATT/XEXT SW 45 Q300, 301 Q302-304 CHARGE SWITCH F305 F304 F303 F302 5.2V REG F301 BATT UNREG 49 Q315-317,324 MT 5.2V 54 56 MT 5.2V BATT UNREG J901 BATTERY TERMINAL
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CHARGE INH 44 SHOE ON 33 BATT SIG
S
2 3 4 BATT SIG
J902 DC IN 1 2 BATT/XEXT 3 CN301
INIT CHARGE ON
50 52 35 37
VTR UNREG
ACV UNREG
SHOE UNREG
BATT FET ON
CHARGE INH
TRF 2.8V Q306, 307 D308 T300 EMERGENCY DETECT DC/DC CONVERTER
SHOE ON
IC300
(1/2)
5 Q312 SWITCHING 6
P UNREG PANEL 2.8V
L303
L307 L306
MS 3.1V D 3.1V
17 PANEL 13.5V 20 PANEL 4.6V 19
5 D306 RECT
55 2
VCC(0)1234 VCC(0)5678
OUT7-1 OUT7-2 -IN7
64 1 13
Q321 SWITCHING
28
VCC 30 Q313 SWITCHING
AU 4.6V
7 46 8 D307 RECT 49 4 1 2 3 D305 RECT 60 VDD(0)123 VDD(0)567 -IN3 40 57 VSS(0)1234
L304
L308
D 1.9V
51 53
D 1.9V
VSS(0)567 OUT3-1 OUT3-2
53 54 Q322 SWITCHING L319 Q340,341 1.5V REG D 1.5V 32 47
A 2.8V AU 2.8V 28 D 2.8V
1
TO POWER BLOCK DIAGRAM (2/3) (VC-358)
IC301
Q314 SWITCHING AMP L305 L312 L314 L315 IC301 ERR AMP
34
(2/2)
D 2.8V AU 2.8V A 2.8V PANEL 2.8V
24 26
D 1.5V
8 7
+IN8 -IN8 OUT2-1 50 51
(SEE PAGE 3-11)
3 Q305 SWITCHING
OUT8
OUT2-2
Q323 SWITCHING
L309 Q325 EMERGENCY DETECT L317
EVF 2.8V 39 EVF 13.5V PANEL 13.5V RP 4.6V 55 41 A 4.6V Q327,331,332,337 13.5V REG L318 22 D 3.1V
-IN2
43 T301 Q308 SWITCHING 4 5 6 7 8 2 D312 RECT D311 RECT
VREF
27
VREF OUT4 -IN4 56 37 1
Q344,348,349,351 CAM 12V 12V REG 18 TRF 2.8V
CAP VS D313 RECT 40 Q333-335,338 CAM -7V -7V REG 46 DRUM VS 38 CAP ERROR
33 34 35
VB RT CT
COMP
11
3
Q309 SWITCHING
L302
L316 L311
DRUM ERROR PANEL 4.6V A 4.6V RP 4.6V AU 4.6V EVF BL 4.6V 48
OUT1-1 OUT1-2 VTR DD ON 29 30 CTL1-6,8 CTL7 -IN1
47 48
Q318 SWITCHING
L313 L310
44 Q310 SWITCHING 13 L300 CAP VS 15
CAM 12V CAM -7V MS 3.1V 14 Q319 SWITCHING
OUT6-1 OUT6-2
61 62
+IN6
18 Q311 SWITCHING L301
CAP ERROR 21 36
EVF 2.8V EVF 13.5V
DRUM VS
R391,392
EVF BL23 EVF BL+ 25
OUT5-1 OUT5-2
58 59
Q320 SWITCHING
CN450
DRUM ERROR +IN5 22
16
3-9
3-10
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
3-6. POWER BLOCK DIAGRAM (2/3)
VC-358 BOARD IC1104
CN021 CHARGE INH SHOE ON BATT SIG INIT CHARGE ON VTR DD ON CAM DD ON 30 FAST CHARGE BATT XEXT SW BATT UNREG 41 46 50 D1103 2 43 34 44 28 32 90 91 BATT SENS ACV SENS SHOE ON IB SO IB SI 81 49 48 I/F EVF VCC 11 INIT CHARGE ON RESET 3 D1104 53 55 D1102 7 REG 3 6 5 38 42 51 86 87 XRESET VDD FAST CHARGE CHARGE INH VTR DD ON CAM DD ON 25 29 28 50 47 66 14 15 20 CN009 7 8 CAMERA 9 MEMORY 2 D 2.8V ZOOM VR POWER VCR (CHG) 8 9 CN002 EVF BL 4.6V 17 20 21 1 Q1104 CN006 BATT SIG 32 32 CN301 HI CONTROL
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
(15/18)
JK-267 BOARD
LANC DC
J303 LANC DIGITAL I/O
LB-100 BOARD
CN200 CN201
LCD903 LCD UNIT
(16/18)
IC1102
(16/18)
IC1101
REG
MT 5.2V
IC1103
LANC I/O 1 UNREG POWER 4
BATTER IN DETECT
4 8
61
BATT IN
BATT/XEXT XVTR MODE SW XCAM+STBY SW
(15/18)
VTR UNREG
49 51 12 Q1106 14 LANC DC VCC 8 XLANC ON
XPHOTO STBY SW
CONTROL SWITCH BLOCK (CF-4980)
IC221
BACK LIGHT DRIVE
BACK LIGHT LED D201
CHIME PWR CONT
7
CK-140 BOARD
D 2.8V SHOE UNREG 36 38 32 32 P UNREG PANEL 2.8V 5 6 18 Q1011 REG VTR UNREG PANEL 4.6V 8 PANEL 13.5V PANEL 4.6V 19 20 LANC DC AU 4.6V 10 10 2 4 2 4 EVER 3.0V 14 14 CN008 6 CN250 CN252 6 8 PANEL 2.8V 6 PANEL 13.5V 6 P UNREG 7 UNREG 5 TO POWER BLOCK DIAGRAM (3/3) (PD-217) 7 BTT LI 3V CN251 44 44 SHOE UNREG S256 RESET CN255 3 EXPOSURE IRIS DIAL
CONTROL SWITCH BLOCK(ED-4980)
2
(16/18)
(15/18)
(17/18)
(17/18)
(SEE PAGE 3-13)
IC1001
AU 4.6V 29 L1073
IC1002
AUDIO ADC&DAC L1002
1
TO POWER BLOCK DIAGRAM (1/3) (DD-216) D 1.9V 52 54 A 2.8V 48
AUDIO I/O FB1002 L1001
IC1092 IC1008
ATT,AMP
IC1005
EVR
(13/18)
(13/18)
IC502
EEPROM
IC501
MECHA CONTROL
105
XREEL HALL ON
CN004 D 2.8V 9 VTR UNREG BATT LI 3V 5 6 4 15 16 AU 2.8V 12 AU 4.6V 14 LI
TO POWER BLOCK DIAGRAM (3/3) (FK-088)
3
A 2.8V FB501
(SEE PAGE 3-10)
(SEE PAGE 3-13)
SHOE UNREG
AU 2.8V D 2.8V
27 31 33
AU 2.8V D 2.8V FB901 L902 FB1301 EVER 3.0V
VCC 36 D 3.1V D 2.8V 73 A 4.6V 75 MT 5.2V 78 80 CN023 70 72
D 1.5V
23 25
TO POWER BLOCK DIAGRAM (3/3) (LA-028)
4
IC903
A/D CONV. D 3.1V 40 42 A 4.6V 21 A 4.6V D 3.1V RP 4.6V 56 RP 4.6V MT 5.2V D 1.9V D 2.8V
IC1301
VIDEO LINE IN/OUT AMP L1301,1304
IC301
DV SIGNAL PROCESS
IC361
DV INTERFACE
IC302
CHARACTER GENERATER
(SEE PAGE 3-13)
(10/18)
(9/18)
(6/18)
(7/18)
(7/18)
M902 HE VCC 15 26 27 Q1109,1108 CN024 CHIME VDD 7 CN901 4PIN CONNECTOR H901, H902 SENSOR VCC R024
CHIME PWR CONT XREEL HALL ON
(14/18) (14/18)
MR VCC
CAPSTAN MOTOR
IC401
13 25 MR VCC HE VCC DRUM ERROR 52 54 11 DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP
FB706 TRF 2.8V 17 L802 EVF 13.5V L801 FB771 FB772 L701 FB707 L702 CAP_VS 37 45 39 47 EVR CAMERA CONTROL EEPROM CAMERA SIGNAL PROCESS S/H AGC A/D CONV. D 2.8V VTR UNREG MT 5.2V 18 22
IC402
Q402 13
(12/18)
CAP VS CAP ERROR DRUM VS DRUM ERROR
(12/18)
(12/18)
CAP ERROR CAPSTAN MOTOR DRIVE, CAP FG AMP DRUM VS
T REEL, S REEL SENSOR
IC803
IC802
IC801
IC771
IC704
IC706
L402
L401
D901 TAPE LED A CN022 15 TAPE LED
R424
CAM 12V CAM -7V
(2/18)
14 16
(1/18)
(1/18)
C MECHA DECK
RP 4.6V L1803 FB1801 EVF VCC L102
MS 3.1V
13
EVF 2.8V
22 L1801
(11/18)
(3/18)
L103 L101 FB101
D 1.9V CN025 A 4.6V 39 39 CAM DD ON Q701,702 CAM 12V MS VCC ON CAM -7V REC/PB AMP EQ, A/D CONV. PLL 38 38 Q1404,1405 48 48 AMP(G-CH) L106
CD-512 BOARD IC103
L100 CCD IMAGER (G-CH)
IC1802
(11/18)
EVF 13.5V 35 EVF BL24 EVF BL+ 26 RGB DRIVE
IC1803
TIMING GENERATOR EVF 13.5V EVF BL 4.6V
IC1407
(8/18)
DIGITAL STILL PROCESS
IC102
IC101
(8/18)
IC101
FB1404
(5/18) (4/18)
L710
(1/18) (1/18)
L104 23 23
IC104
AMP(R-CH) L101
IC1404
CN007 FOR ADJUSTMENTS 20 17
IC1403
(3/18)
16M DRAM
IC1409
(3/18)
JPEG
IC1408
(5/18)
16M DRAM
IC1406
(4/18)
EEPROM
IC1401
(4/18)
DIGITAL STILL CONTROL FB1403 118
IC1412
SHUTTER SOUND
IC1410 IC1411
MEMORY STICK I/F
IC102
CCD IMAGER (R-CH)
IC705
TIMING GENERATOR
(4/18)
RS232C I/F
IC701 IC702
CCD V DRIVE
34 34 24 24
L105 14 14
IC105
AMP(B-CH) L107
IC100
CCD IMAGER (B-CH)
D 2.8V MS 3.1V
FB1401
FB1402
FB1406
FB1405
R1455
D 2.8V FB704
8
8
12 12 CN100
16
FB1407
3-11
3-12
DCR-VX2100/VX2100E
3. BLOCK DIAGRAMS
3-7. POWER BLOCK DIAGRAM (3/3)
PD-217 BOARD
PANEL 4.6V 7 PANEL 2.8V 5 PANEL 13.5V 6 CN2100 L2103 L2101 L2102 14 P OFF CN2104 18 LCD UNIT Q2102,2104 VDD LCD901
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
RM-091 BOARD
D 2.8V 1 LI D 3.1V MT 5.2V 5
CN801
S803,804,801 ZOOM SW ZOOM SPEED SW
2
TO POWER BLOCK DIAGRAM (2/3) (CK-140)
IC2101
RGB DRIVE
IC2103
TIMING GENERATOR 4 ND901 BACKLIGHT INVERTER BLOCK BACK LIGHT DRIVE 7 7 CN1701
BT801,802
(SEE PAGE 3-12)
HL-013 BOARD IC1701
LCD INDICATOR DRIVE
R1121
R1125
ZM-030 BOARD
SIRCS SIG SELECTOR
BL ON
TALLY LED (REAR) D1105
IC1102
REMOTE COMMANDER RECEIVER (REAR)
D1107-1110
UNREG 7 EVER 3.0V 6 CN2101 CN2103
3
TO POWER BLOCK DIAGRAM (2/3) (VC-358)
CN502 CN501 D 2.8V 10 UNREG LI 5 6 3 VTR FUNCTION KEY ILLUMINATION LED 4 5 16 8 CN053 15 16 AU 2.8V 11 AU 4.6V 13 15 11 1 27 D 3.1V 23 MT 5.2V 13 2 22 CN1103 3 12 CN703 CN702 5 5 CN750 R750 D750 TALLY LED (FRONT) CN500 CN1100 10 7 14 17 8 5 7 10 17 29 12 12 Q701,703, 705-707 4 4 R751 SHOE UNREG 12 13 25 26 8 9 15 18 L1150 MIC AMP MIC POWER IR LED DRIVE Q700, 702, 704 REMOTE COMMANDER RECEIVER (FRONT) D500-511 7 1 2 INTELLIGENT ACCESSORY SHOE
FT-092 BOARD
IC1150
CN1102 MIC AMP
3 4
(SEE PAGE 3-12)
MI-050 BOARD
IC750
4
TO POWER BLOCK DIAGRAM (2/3) (VC-358)
FK-088 BOARD
VCC 35 69 71 D 2.8V 74 A 4.6V 76 77 79 CN051 MT 5.2V R178 R186 D 3.1V
MA-430 BOARD
(SEE PAGE 3-12)
SE-147 BOARD
Q200,201 L200 L142 11 SE VCC 4 CN600 PITCH/YAW SENSOR
F750 D751 IR LED (SIRCS OUTPUT)
(1/3)
(1/3)
(1/3)
(2/3)
IC143
FOCUS RING PHASE DETECTOR
IC144
ZOOM RING PHASE DETECTOR
IC141 IC142
IRIS DRIVE, V REF
IC200
PITCH/YAW SENSOR AMP
LENS BLOCK
Q140,141 ZMFC SENS VCC 26 ZOOM RESET SENSOR FOCUS RESET SENSOR
D003 ACCESS LED CN001 D 2.8V 4 9 Q073,074
L143
ND SENS VCC 32 L141 R187 21 CN050 FB140 L140 L070 L071 Q072,075 L072 2 Q077 MZ VCC ZOOM RING ND FILTER SW DRIVE + IRIS METER
MK-016 BOARD
(1/3)
Q076,078
(2/3)
(2/3)
3 9
VCC
3 4
15 16 CN056
IC140
ZOOM MOTOR FOCUS MOTOR DRIVE
IC070-072
ACTIVE PRISM ACTUATOR DRIVE VAP LOCK DRIVE
CN776 MEMORY STICK SLOT
CN775
IC075 IC076
P PWM Y PWM AMP
IC073,074
ACTIVE PRISM ACTUATOR PRE DRIVE L073
MF VCC 10 FOCUS RING
(2/3)
MS-209 BOARD
VAP VCC 11 CN052
LA-028 BOARD
ACTIVE PRISM ACTUATOR
16
3-13
3-14E
DCR-VX2100/VX2100E
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3)
1 2 3 4 5 6 7 8 9 10 11
CN100 1 GND H1B SUBB GND B_CCD_OUT GND V2BB V3B GND R_CCD_OUT GND VDD2R V2AR V1R H1R SUBR GND G_CCD_OUT GND VDD2G V2AG V1G H1G SUBG GND 50P
12
CN025 GND H2B RGB VDDB GND VLB VDD2B V2AB V1B GND GND VLR V2BR V3R H2R RGR VDDR GND VLG V2BG V3G H2G RGG VDDG GND 2 4 6 8 10 12 14 16
13
14
15
16
17
18
19
20
A
LENS UNIT
CCD IMAGER
3
CD-512 BOARD
CCD IMAGER
5 7 9 11 13
RM-091 BOARD
CN502 21P 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 21P REG_GND REG_GND REG_GND REG_GND F_TALLY_LED D_3.1V SIRCS_SEL1 TALLY_LED XCUSTOM_PRESET SIRCS_SEL2 SIRCS_SIG MT_GND MT_GND MT_5.2V D_2.8V SIRCS_SIG1 LI LI H_ZOOM_AD XS/S_SW(HAND) ZM_SPD_SEL 7P D_2.8V ZM_SPD_SEL XS/S_SW(HAND) H_ZOOM_AD LI REG_GND REG_GND 1 2 3 4 5 6 7 1 2 3 4 5 6 7 CN801 7P D_2.8V ZM_SPD_SEL XS/S_SW(HAND) H_ZOOM_AD LI REG_GND REG_GND REG_GND REG_GND REG_GND
CCD IMAGER
15 17
18 20 REG_GND 22 24 26 28 30 XCUSTOM_PRESET 32 SIRCS_SEL2 34 SIRCS_SIG 36 MT_GND 38 MT_GND 40 MT_5.2V 42 D_2.8V 44 SIRCS_SIG1 46 LI 48 LI 50 H_ZOOM_AD XS/S_SW(HAND)
B
SE-147 BOARD
6P
19 21 23 25 27 29
CN600
1
CONTINUED ON
F_TALLY_LED D_3.1V
ZM-030 BOARD
(PAGE 4-3)
SIRCS_SEL1 TALLY_LED
31 33 35
PSD_OUT
SE_VCC
PS_REF
YS_REF
C
YSD_OUT
GND
37 39 41 43 45 47 49
6
5
4
3
2 9
D
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
8
1 7
6
5
4
3
2
MZ_GND
GND
GND
GND
1
ZOOM_B
ZOOM_A
MF_GND
NDC
NDA
NDB
P_DUMP_A
P_DUMP_B
Y_DUMP_A
Y_DUMP_B
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
TEMP_OUT
MZ_VCC
TEMP_OUT
VAP_GND
MF_VCC
PSD_OUT
YSD_OUT
LOCK+
Y_OUT
P_OUT
ZOOM_A-
NC
ZM_RST