Text preview for : ETE-3 UOC TDA111xx, TDA121xx SM.pdf part of China service manual for TDA111xxPS, TDA121xxPS
Back to : ETE-3 UOC TDA111xx, TDA12 | Home
COLOR TELEVISION
SERVICE MANUAL
MODELNO.PF21GB300
CHASSISNO.ETE-3
Please read this manual carefully before service.
1 / 32 1 / 32
CONTENTS
Part I. Safty instructions and maintenance 1.1 X-Ray Radiation precaution..................................................... 3 1.2 Safety Precaution.......................................................................3 1.3 Product Safety Notice................................................3 1.4 Safety Symbol Description..........................................4 1.5 Maintenance........................................................... 5 Part II. Adjustments 2.1 Set-up Adjustments................................................... 5 2.1.1 Color Purity Adjustment...................................... 5 2.1.2 Convergence Adjustment..................................... 6 2.1.3 White Balance Adjustment....................................8 2.2 Circuit Adjustments...................................................8 2.2.1 Degaussing.......................................................9 2.2.2 Confirmation and Adjustment for Voltage..................9 2.2.3 High Voltage Inspection......................................10 2.2.4 Lian grid, focus of the adjustment and white balance adjust.......................................11 2.2.5 Service Mode....................................................12 PartIII. Struction and Chassis Function Description 3.1 Structure Block Diagram...........................................18 3.2 Chassis Description..................................................18 3.2.1 General Description...........................................18 3.2.2 The ICs and Assemblies the Chassis mainly uses.........19 PartIV. Service Data 4.1 TV Signal Processor TDA111XX series...........................20 4.1.1 General Description............................................20 4.1.2 Features of TV processor......................................20 4.2 TFA9842AJ............................................................24 4.2.1 General Description............................................24 4.2.2 Features..........................................................24 4.2.3 Block diagram of TFA9842AJ................................25 4.2.4 Pining.............................................................25 4.2.5 Pin Description..................................................26
2
4.3 Vertical Scan Output Stage Circuit...............................26 4.3.1 Features..........................................................................26 4.3.2 General Description........................................27 4.3.3 Block Diagram of TDA4864AJ...........................27 4.4 EEPROM AT24C16................................................28 4.4.1 Features......................................................28 4.4.2 Pin Description..............................................28 4.4.3 Memory Organization......................................29 4.4.4 Block Diagram..............................................29 4.5 Switch-mode Power Supply IC FSCQ0765RT................30
3
1. SAFETY INSTRUCTIONS AND MAINTENANCE WARNING: Before serving the chassis, please read the "x-Ray radiation precaution", "safety precaution" and "product safety notice" instruction below. 1.1 X-RAY RADIATION PRECAUTION 1.1.1 The EHT must be checked every time the TV is serviced to ensure that the CRT does not emit X-ray radiation as result of excessive EHT voltage. The maximum EHT voltage permissible in any operating circumstances must not exceed the rated value. When checking the EHT, use the High Voltage Check procedure in this manual using an accurate EHT voltmeter. 1.1.2 The only source of X-RAY radiation in this TV is the CRT. The TV minimizes X-RAY radiation, which ensures safety during normal operation. To prevent X-ray radiation, the replacement of CRT must be identical to the original fitted way as specified in the parts list. 1.1.3 Some components used in this TV have characteristics concerning safety to prevent the CRT from emitting X-ray radiation. For continued safety, replacement component should be made after referring the PRODUCT SAFETY NOTICE below. 1.1.4 Service and adjustment of the TV may result in changes in the nominal EHT voltage of the CRT anode. So ensure that the maximum EHT voltage does not exceed the rated value after service and adjustment. 1.2 SAFETY PRECAUTION WARNING: Refer servicing to qualified service personal only. 1.2.1 The TV has a nominal working EHT voltage. Extreme caution should be exercised when working on the TV with the back removed. Do not attempt to service this TV if you are not conversant with the precautions and procedures for working on high voltage equipment. When handling or working on the CRT, always discharge the anode to the
4
TV chassis before removing the anode cap in case of electric shock. The CRT, if broken, will violently expel glass fragments. Use shatterproof goggles and take extreme care while handling. Do not hold the CRT by the neck as this is a very dangerous practice.. 1.2.2 Voltage exists between the hot and cold ground when the TV is in operation. Install a suitable isolating transformer of beyond rated overall power when servicing or connecting any test equipment for the sake of safety. 1.2.3 When replacing ICs, use specific tools or a static-proof electric iron with small power (below 3 5W). 1.2.4 Do not use a magnetized screwdriver when tightening or loosing the deflection yoke assembly to avoid electronic gun magnetized and decrement in convergence of the CRT. 1.2.5 When remounting the TV chassis, ensure that all guard devices, such as nonmetal control buttons, switch, insulating sleeve, shielding cover, isolating resistors and capacitors, are installed on the original place. 1.2.6 Replace blown fuses within the TV with the fuse specified in the parts list. 1.2.7 When replacing wires or components to terminals or tags, wind the leads around the terminal before soldering. When replacing safety components identified by the international hazard symbols on the circuit diagram and parts list, it must be the company-approved type and must be mounted as original. 1.3 PRODUCT SAFETY NOTICE WARNING: For your protection, the following product safety notice should Be read carefully before operating and servicing this TV set. 1.3.1 Many electrical and mechanical components in this chassis have special safety-related characteristics. Components which have these special safety characteristics in this manual and its supplements are identified by the
5
international hazard symbols on the circuit diagram and parts list. Before replacing any of these components please read the parts list in this manual carefully. Substitute replacement components which do not have the same safety characteristics as specified in the parts list may create X-ray radiation. 1.3.2 Do not slap or beat the cabinet or CRT, since this may result in fire or explosion. 1.3.3 Never allow the TV sharing a plug or socket with other large-power equipment. Doing so may result in too large load or cause fire. 1.3.4 Do not allow anything to rest on or roll over the power cord. Protect the power cord from being walked on, modified, cut or pinched, particularly at plugs. 1.3.5 Do not place any objects, especially heavy objects and lightings, on top of the TV set. Do not install the TV near any heat sources such as radiators, heat registers, stove, or other apparatus that produce heat. 1.3.6 Service personnel should observe the SAFETY INSTRUCTIONS in this manual during use and servicing of this TV set. Otherwise, the resulting damage is not protected by the manufacturer. 1.4 SAFETY SYMBOL DESCRIPTION The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. Extreme caution should be exercised when working on the TV with the back removed. This is an international hazard symbol, telling you that the components identified by the symbol have special safety-related characteristics. UL This symbol tells you that the critical components identified by the UL marking have special safety-related characteristics. VDE or TUV This symbol tells you that the critical components identified by the VDE/TUV marking have special safety-related characteristics.
6
1.5 MAINTENANCE 1.5.1 Do not place the set near or over a radiator or heat register, or where it is exposed to direct sunlight. 1.5.2 Do not install the TV set in a place exposed to rain, water, excessive dust, mechanical vibrations or impacts. 1.5.3 Allow enough space (at least 10cm) between the TV and wall or enclosures for proper ventilation. 1.5.4 Please power off the TV set and disconnect it from the wall immediately if any abnormal condition is met, such as bad smell, belching smoke, sparkling, abnormal sound, no picture/sound/raster. Hold the plug firmly when disconnecting the power cord. 1.5.6 Unplug the TV set from the wall outlet before cleaning or polishing it. Use a dry soft cloth for cleaning the exterior of the TV set or CRT screen. Do not use liquid cleaners or aerosol cleaners. 2. ADJUSTMENTS 2.1 SET-UP ADJUSTMENTS The following adjustments should be made when a complete realignment is required or a new picture tube is installed. Perform the adjustments in the following order: Color purity Convergence White balance 2.1.1 Color Purity Adjustment Preparation: Before starting this adjustment, adjust the vertical sync, horizontal sync, vertical amplitude and focus. Measures: ·Face the TV set north or south.
7
·Connect the power plug into the wall outlet and turn on the main power switch of the TV set. ·Operate the TV for at least 15 minutes. ·Degauss the TV set using a specific degaussing coil. ·Set the brightness and contrast to maximum. ·Counter clockwise rotate the R /B low brightness potentiometers to the end and rotate the green low brightness potentiometer to center. ·Receive green raster pattern signals. ·Loosen the clamp screw holding the deflection yoke assembly and slide it forward or backward to display a vertical green zone on the screen. Rotate and spread the tabs of the purity magnet around the neck of the CRT until the green zone is located vertically at the center of the screen. ·Slowly move the deflection yoke assembly forward or backward until a uniform green screen is obtained. ·Tighten the clamp screw of the assembly temporarily. Check purity of the red raster and blue raster until purities of the three rasters meet the requirement.
2.1.2 Convergence Adjustment Preparation: Before attempting any convergence adjustment, the TV should be operated for at least 15 minutes. Measures:
8
·Center convergence adjustment. ·Receive dot pattern. ·Adjust the brightness/contrast controls to obtain a sharp picture. ·Adjust two tabs of the 4-pole magnet to change the angle between them and red and blue vertical lines are superimposed each other on the center of the screen. ·Turn both tabs at the same time keeping the angle constant to superimpose red and blue horizontal on the center of the screen. ·Adjust two tabs of the 6-pole magnet to superimpose red/blue line and green line. ·Remember red and blue movement. Repeat steps 2.1.3 2. 1.5 until optimal convergence is obtained. ·Circumference convergence adjustment. ·Loosen the clamp screw holding the deflection yoke assembly and allow it tilting. ·Temporarily put the first wedge between the picture tube and deflection yoke assembly. Move front of the deflection yoke up or down to obtain better convergence in circumference. Push the mounted wedge in to fix the yoke temporarily. ·Put the second wedge into bottom. ·Move front of the deflection yoke to the left or right to obtain better convergence in circumference. ·Fix the deflection yoke position and put the third wedge in either upper space. Fasten the deflection yoke assembly on the picture tube. ·Detach the temporarily mounted wedge and put it in either upper space. Fasten the deflection yoke assembly on the picture tube. ·After fastening the three wedges, recheck overall convergence and ensure to get optimal convergence. Tighten the lamp screw holding the deflection yoke assembly.
9
2.1.3 White Balance Adjustment For TVs with I2C bus control, change the bus data to adjust white balance. 2.2 CIRCUIT ADJUSTMENTS Preparation: Circuit adjustments should be made only after completion of set-up adjustments. Circuit adjustments can be performed using the adjustable components inside the TV set. For TVs with 2 I C bus control, first change the bus data. 2.2.1 Degaussing A degaussing coil is built inside the TV set. Each time the TV is powered on, the degaussing coil will automatically degauss the TV. If the TV is
10
magnetized by external strong magnetic field, causing color spot on the screen, use a specific degausser to demagnetize the TV in the following ways. Otherwise, color distortion will be shown on the screen. ·Power on the TV set and operate it for at least 15 minutes. ·Receive red full-field pattern. ·Power on the specific degausser and face it to the TV screen. ·Turn on the degausser. Slowly move it around the screen and slowly take it away from the TV. ·Repeat the above steps until the TV is degaussed completely. 2.2.2 Confirmation and Adjustment for Voltage Caution: +B voltage has close relation to high voltage. To prevent X-ray radiation, set +B voltage to the rated value. The maximal radiator is not GND by reason of linking to TP--12V. Measures: ·Make sure that the supply voltage is within the range of the rated value. ·Connect a digital voltmeter to the voltage output terminal of the main PCB. Power on the TV and set the brightness and sub-brightness to minimum. Ensure that the voltage from the main PCB reads as follows. ·Regulate voltage adjustment components on the power section until the +B the voltage reaches the rated value.
11
Test Point
Voltage (21SS) 311 5V
Voltage (21US) 311 5V
Voltage (Others) 311 5V
TP-310V
TP-103V
104 1.5V
104 1.5V 184 3V
115 1.5V 184 3V
TP-184V
184 3V
TP-+12V TP--12V
13 1V 13 1V
16 1V -16 1V
13 1V 13 1V
TP-22V TP-35V TP-36V TP-5V-1 TP-8V TP-5V-2V TP-3.3V
22 1V 35 1V 36 1V 5 0.3V 8 0.3V 5 0.3V 3.3 0.3V
22 1V 35 1V 36 1V 5 0.3V 8 0.3V 5 0.3V 3.3 0.3V
22 1V 35 1V 36 1V 5 0.3V 8 0.3V 5 0.3V 3.3 0.3V
Note: It's impossible to check the power part separately from the main chassis board as the part is mounted on the main chassis board. The power components, etc. should be checked for burnout when power-on. If burned out, do not power on the TV again until the cause is found out.
2.2.3 High Voltage Inspection Measure voltages of test points on the main PCB with the digital voltmeter.
12
Measure the CRT high voltage with the high-voltage testing equipment and heater voltage with the high-frequency effective voltmeter. The rated values are shown as below. Test Point Negative of 21 21"US CRT Voltage 184±3V 25.5±1.5KV 25.5±1.5KV Test Point 14"GS_CRT_ano 21 21"US CRT anode Voltag 22±1.5K 26.5±1.5K 23.5±1.5K V
anode (HUAFEI) Heater 6.3±0.3Vrms
2.2.4 . Lian grid, focuse of the adjustment and white balance adjust Caution: Dangerously high voltages are present inside the TV. Extreme caution should be exercised when working on the TV with the back removed. Measures: ·Power on the TV and preheat it for 15 min. ·Pack P.MODE key to work a television at the natural mode. ·Counterclockwise to adjust the Lian grid to the least. ·Press VSD key of factory remote control, clockwise adjust the Lian grid , adjust to the screen to at the right moment appear a horizon; ·Adjust parameter BLOR, BLOG and BLOB under the horizonadjust the horizon as white.( Generally don't adjust BLOG) ·And then press VSD key again, Adjust Lian grid, make the horizon accommodation(not dazzling, white, if it doesn't white repeated step until white) ·Regulate to focuse , make the light grid focuse good,and you get a sharp picture. 2.2.5 SERVICE mode Entering the SERVICE mode Set the volume to 0. Then press and hold the MUTE button on the remote control, and press the MENU button on the TV to enter the SERVICE mode. To exit from the SERVICE mode, turn off the TV set by the POWER button
13
on the remote control. Caution: The user service mode adjustment can be changed only when service personnel adjust the whole set data during servicing. As the control data have dramatic effects on functions and performance of the TV,service personnel should not tell user how to enter the SERVICE mode to avoid improper data settings. Adjustments and bus data: Symbo l Page 0 V-Bri VSD Pic Brightness Displayed Vertical Scan Disable 32 32 The OTP Software NO Displayed AsGDET03**-** Description Data
Page 1 HSH HPAR
G-0 When Vertical Frequency is Identified as 50Hz,Then 50Hz will be displayed; so is 60Hz. Horizental Shift Horizental Parallelogram Correction 32/38 26/28 32/32 32/32 32/32 53/51 22/18
HBOW Horizental BOW Correction VLIN VSCR EWW PW Vertical Linearity Vertical Scroll E-W Width E-W Parabola Width
Page 3 UCP LCP
G-2
E-W Upper Corner Parabola E-W Bottom Corner Parabola
46/37 42/33
14
TC VSH VA SC VSL
E-W Trapezium Vertical Shift Vertical Amplitude Vertical S Correction Vertical Slope
32/32 36/36 22/22 32/24 32/31
Page 3
G-2
ZOOM Vertical zoom 169 16 ZOOM Vertical zoom normal 43 N ZOOM Vertical zoom expand zoom EX OSD-V 50Hz OSD VERTICAL SHIFT 5 OSD-V 60Hz OSD VERTICAL SHIFT 6 Fac Init Factory Bus open EEPROM init
0
25
51
50
46 0 0
Page 4 BLOC BLOR BLOG BLOB WPR
W-tone
Common course black level offset Fine black level offset R Fine black level offset G Fine black level offset B White point R
7 32 32 32 32
15
WPG WPB
White point G White point B
32 32
Page 5 IF TOP AGCS OIF T-SET TXT-H -POS TXT RGB
Tuning
IF selection
3 20
IF AGC SPEED Off-set if demodulatour
1 32
10
15
Page 6 NTSC SECA M BG-A2 M L
SYS
1 1 0 1 0 2 1
O-SYS 0:DK;1:BG A2;2:BG;3:I;4:M;5:L O-LA NG Prepare to place OSD Language
16
Page 7 AVLE AVL DEG
MENU
AVL/EW function select AVL function DEGAUSS
0 0 0 0 0 0 2
B-TRE Sound effect DISG COF DCXO Gain selection of DISCO Cut-off control range Crystal Frequency Correcting Compensation
Page 8 S-VID EO M-ON OFF-T IME LOGO -ACT NO-SI G LOG0 LOG1
OTHER
S-VIDEO Set
0 1
Memory on Auot off without signal. 0:5 Minutes; 1:10 Minutes; 2: 15Minutes User's logo setup
0
1
Have no signal to hint
1 1 6
Logo color 0 Logo color 1
Page 9
SUB
17
S-BRI
Sub bright
0 63 0 63
M-BRI Max bright S-CON Sub contrast M-CO N MX-C OL LOG-T LOGO Sellection VX-V AM Max color Max contrast
63 0 0
Page 10 PWLD AC CORDEF SSL FSL AAS XDT
Video-0
15 Noise Reducing
1 0 0 2 0
Slicing level Forced slicing level for vertical sync Black area to switch off the black stretch X-ray detection
Page 11
Audio-0
AMLO Audio output signal for AM sound/AM W GSSIF Extra gain-range SSIF for AM
0
0
18
demodulation DSG AGN AGNE Gain from audio inputs to audio outputs Gain FM demodulator Extended gain settings for FM demodulator 0 1 0
Page 12 T.mod
Audio-1
EHT Compensation Set
1 1 1 1
FMWS Window select for FM demodulator BPB2 FFI Bypass sound bandpass filter section 2 Fast filter IF-PLL
Page 13 CL SOC
Video-1
Cathode drive level Soft clipping level PAL/NTSC ident sensitivity (burst
12 2
CHSE
amplitude at strong signal (typical value)
2
CLO HBL WBF WBR
Centre frequency of cloche filter
1 1 0 8
Notes: The data sheet may differ dependent on different models. The data sheet may differ dependent on different CRTs for the same model.
19
3. STRUCTURE AND CHISSIS FUNCTION DESCRIPION 3.1 STRUCTUE BLOCK DIAGRAM
IR KEY Video Amplifier
UOC-TOP TUNER
H.OUT V.OUT
Side AVIN
RCA/SCART
3.2 CHASSIS DESCRIPTION 3.2.1 General Description ETE-3 chassis is applied in SS21GG300A series. By the use of Philips UOC-TOP for TV small signal processing and bus control, the chassis enables TV tuning, adjustment, control and picture correction, featuring high-integration, high-performance-to-price ratio and high-reliability and compact circuit with fewer external components. The chassis, widely used in small and medium TVs, provides much more convenience for manufacturing and technical service. Features: ·Color systems: PAL, SECAM (OPT), NTSC(OPT)
AVOUT
20
Power Supply Circuit
Audio Amplifier
·Sound systems: D/K, B/G, I , M(OPT) ·236 programs preset ,AV stereo, Hotel , Child lock , Teletext OPT,ZOOM, Channel swap, Recall, Timer. ·UOC TDA11136PS/N3/3 for PAL/NTSC /SECAM small signal processing and bus control EEPROM AT24C16 for data memory. ·TDA4864AJ for vertical output power amplifying ·TFA9842AJ for audio power amplifying ·Thick-film IC FSCQ0765RT for power circuit adjustment and control 3.2.3 The chassis mainly uses the following ICs and assemblies Positio Type N201 AT24C16 N202 TDA111XXPS TDA121XXPS ` 4 5 6 N601 N300 N801 A001 TFA9842AJ TDA4864AJ TDA4865AJ FSCQ0765 TAF5-C4I23 TAF5-E4I22 TAF5-U2F22 Description EERPOM Micro processor,MONO-90 /MONO110 Versions for 90 Micro processor,AV -90/AV-110 Versions for Audio power amplifier For Ultra-slim CRT Switch-mode power supply IF 38MHz tuner IF 38.9MHz tuner IF 45.75MHz tuner
1 2
4. SERVICE DATA 4.1 TV signal processor TDA111XX series 4.1.1 GENERAL DESCRIPTION The various versions of the TDA111XX /TDA121XX series combine the functions of a video processor together with a -Controller and US Closed Caption decoder. Most versions have a Teletext decoder on board. The Teletext decoder has an internal RAM memory for 1 page text. The ICs are intended to be used in economy television receivers with 90and 110picture tubes. The ICs have
21
supply voltages of 8 V and 3.3 V and they are mounted in an SDIP-64 envelope. The features are given in the following feature list. 4.1.2 FEATURES of TV processor Available in TDA111XX versions ·Multi-standard vision IF circuit with alignment-free PLL demodulator ·Internal (switchable) time-constant for the IF-AGC circuit ·The mono intercarrier sound circuit has a selective FM-PLL demodulator which can be switched to the different FM sound frequencies (4.5/5.5/6.0/6.5 MHz). The quality of this system is such that the external band-pass filters can be omitted. ·The FM-PLL demodulator can be set to centre frequencies of 4.72/5.74 MHz so that a second sound channel can be demodulated. In such an application it is necessary that an external band pass filter is inserted. ·Integrated chrominance trap circuit ·Integrated luminance delay line with adjustable delay time · Picture improvement features with peaking (with switchable centre frequency, depeaking, variable positive/negative overshoot ratio and video dependent coring) and blue- and black stretching. All features are available for CVBS, Y/C and YPBPR signals. ·Tint control for external RGB/YPBPR signals ·Integrated chroma band-pass filter with switchable centre frequency ·Only one reference (12 MHz) crystal required for the -Controller, Teletextand the colour decoder ·Multi-standard colour decoder with automatic search system ·Internal base-band delay line ·Indication of the Signal-to-Noise ratio of the incoming CVBS signal · A linear RGB/YUV/YPBPR input with fast blanking for external
22
RGB/YUV sources. The synchronisation circuit can be connected to the incoming Y signal. The Text/OSD signals are internally supplied from the -Controller/Teletext decoder. ·RGB control circuit with `Continuous Cathode Calibration', white point and black level off-set adjustment so that the colour temperature of the dark and the light parts of the screen can be chosen independently. ·2 levels of contrast reduction of main picture possible during OSD/Text insertion (`halftone') ·OSD/Text gain reduction control ·Adjustable `wide blanking' of the RGB outputs ·Horizontal synchronization with two control loops and alignment-free horizontal oscillator ·Vertical count-down circuit ·Vertical driver optimized for DC-coupled vertical output stages ·Horizontal and vertical geometry processing ·Horizontal and vertical zoom function for 16:9 applications ·Horizontal parallelogram and bow correction for large screen picture tubes ·Low-power start-up of the horizontal drive circuit ·Macrovision keying possibility for horizontal synchronisation. Controller: ·80C51-controller core standard instruction set and timing ·0.9766 s machine cycle ·maximum of 64 k x 8-bit late programmed ROM ·maximum of 3 k x 8-bit Auxiliary RAM (2 k required for Display) ·I2C byte level bus interface.
23
·Interrupt controller for individual enable/disable with two level priority ·Two 16-bit Timer/Counter registers ·One 24-bit Timer (16-bit timer with 8-bit Pre-scaler) ·16-bit Data pointer ·WatchDog timer ·Auxiliary RAM page pointer ·Stand-by, Idle and Power Down modes ·Up to 13 general-purpose I/O pins ·14 bits PWM for Voltage Synthesis Tuning ·8-bit A/D converter with 4 multiplexed inputs ·4 PWM (6-bits) outputs for analogue control functions
Data Capture: ·Text memory for 1 page ·Inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) ·Data Capture for US Closed Caption ·Data Capture for 525/625 line WST, VPS (PDC system A) and 625 line Wide Screen Signalling (WSS) bit decoding ·Automatic selection between 525 WST/625 WST ·Automatic selection between 625 WST/VPS on line 16 of VBI ·Real-time capture and decoding for WST Teletext in Hardware, to enable optimized -processor throughput ·Automatic detection of FASTEXT transmission ·Real-time packet 26 engine in Hardware for processing accented,G2 and G3 characters
24
·Signal quality detector for video and WST/VPS data types ·Comprehensive teletext language coverage ·Full Field and Vertical Blanking Interval (VBI) data capture of WST data
Display: ·Up to 4 character sets with 256 characters each (size 16 pixels x 18 lines) ·Enhanced OSD modes ·50Hz/60Hz display timing modes ·Serial and Parallel Display Attributes ·Single/Double/Quadruple Width and Height for characters ·Scrolling of display region ·Variable flash rate controlled by software ·Enhanced display features including overlining, underlining and italics ·Soft colours using CLUT with 4096 colour palette ·Global selectable matrix: (12/16) ·Fringe colour selectable ·Contrast reduction of defined area ·Programmable Cursor ·Special Graphics Characters with two planes, allowing four colours per character 4.2 TFA9842AJ 2-channel audio amplifier with volume control (SE: 1 W to 7.5 W) 4.2.1 General description The TFA9842AJ contains two identical audio power amplifiers. The TFA9842AJ can be used as two Single-Ended (SE) channels with a volume control. The maximum gain is 26 dB. The TFA9842AJ comes in a 9-pin DIL-bent-SIL
25
(DBS9P) power package. The TFA9842AJ is pin compatible with the TFA9843AJ, TFA9843(B)J, TFA9842(B)J and TFA9841J. The difference between the TFA9843AJ and the TFA9843(B)J,TFA9842(B)J, TFA9841J is the functionality of pin 7. The TFA9843AJ has a Volume Control (VC) on pin 7. The TFA9843(B)J, TFA9842(B)J and TFA9841J have a mode select (Mode) on pin 7.The TFA9842AJ contains a unique protection circuit that is solely based on multiple temperature measurements inside the chip. This gives maximum output power for all supply voltages and load conditions with no unnecessary audio holes. Almost any supply voltage and load impedance combination can be made as long as thermal boundary conditions (number of channels used, external heatsink and ambient temperature) allow it. 4.2.2 Features ·2 Channel SE: 1 W to 7.5 W operation possibility ·Soft clipping ·Input clamps ·Volume control ·Standby and mute mode ·No on/off switching plops ·Low standby current ·High supply voltage ripple rejection ·Outputs short-circuit protected to ground, supply and across the load ·Thermally protected ·Pin compatible with the TFA9843AJ, TFA9843(B)J, TFA9842(B)J, TFA9841J. 4.2.3 Block diagram of TFA9842AJ
26
4.2.4 Pining
4.2.5 Pin Description Symbol IN2 OUT2 CIV IN1 Pin 1 2 3 4 Description input 2 loudspeaker terminal 2 common input voltage decoupling input 1
27
GND SVR
5 6
ground half supply voltage decoupling (ripple rejection) volume control input (standby, mute and volume control) loudspeaker terminal 1 supply voltage Description
VC OUT1 VCC Symbol
7 8 9 Pin
4.3 VERTICAL SCAN OUTPUT STAGE CIRCUIT 4.3.1 FEATURES TDA4864AJ: Output current up to 2.5A (p-p) 4.3.2 GENERAL DESCRIPTION The TDA4864AJ is deflection boosters for use in vertical deflection systems for frame frequencies up to 200 Hz. The TDA4864AJ needs a separate flyback supply voltage, so the supply voltages are independently adjustable to optimize power consumption and flyback time. For the TA4864AJ the flyback supply voltage will be generated internally by doubling the supply voltage and therefore a separate flyback supply voltage is not needed. 4.3.3 Block diagram of TDA4864AJ
28
PIN SYMBOL DESCRIPTION 1 VP1 positive supply voltage 1 2 VP3 flyback generator output 3 VP2 supply voltage 2 for vertical output 4 GND ground or negative supply voltage 5 V-OUT vertical output 6 INN inverted input of differential input stage 7 INP non-inverted input of differential input 4.4 EEPROM AT24C16 4.4.1 Features Data EEPROM internally organized as 1024/2048 bytes and 64/128 pages×16 bytes Page protection mode, flexible page-by-page hardware write protection -Additional protection EEPROM of 64/128 bits, bit per data page 1-Protection setting for each data page by writing its protection bit -Protection management without switching WP pin Low power CMOS Vcc=2.7 to 5.5V operation Two wire serial interface bus, IIC-Bus compatible Filtered inputs for noise suppression with Schmitt trigger Clock frequency up to 400 kHz
29
High programming flexibility - Internal programming voltage - Self timed programming cycle including erase - Byte-write and page-write programming, between 1 and 16 bytes - Typical programming time 6ms(< 1 0ms) for up to 16 bytes High reliability - Endurance 106 cycles 1) - Data retention 40 years 1) - ESD protection 4000 V on all pins 8 pin DIP/DSO packages Available for extended temperature ranges - - Industrial: -40to +85 Automotive: -40to +125
4.4.2 Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bi-directional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. The AT24C08 only uses the A2 input for hardwire addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1 pins are no connects. 4.4.3 Memory Organization T24C16, 16K SERIAL EEPROM: Internally organized with 64 pages of 16 bytes each, the 16K requires a 10-bit data word address for random word addressing.
30
4.4.4 Block Diagram
4.5 SWITCH-MODE POWER SUPPLY IC FSCQ0765RT
Internal Block Diagram
31
Pin Number 1 2
Pin Name Pin Function Description
Drain GND
High voltage power SenseFET drain connection. This pin is the control ground and the SenseFET source. This pin is the positive supply input. This pin provides
3
Vcc
internal operating current for both start-up and steady-state operation. This pin is internally connected to the inverting input of the PWM comparator. The collector of an opto-coupler is
4
Vfb
typically tied to this pin. For stable operation, a capacitor should be placed between this pin and GND. If the voltage of this pin reaches 7.5V, the over load protection triggers, which results in the FPS shutting down. This pin is internally connected to the sync detect comparator for quasi-resonant switching. In normal
5
Sync
quasi-resonant operation, the threshold of the sync comparator is 4.6V/2.6V. Whereas, the sync threshold is changed to 3.0V/1.8V in an extended quasi-resonant operation.
32