Text preview for : SONY HDR-CX11E, CX12, CX12E SERVICE MANUAL LEVEL 2 VER 1.1 2008.11 (9-852-601-32).pdf part of SONY HDR-CX12 SONY HDR-CX11E, CX12, CX12E
DIGITAL HD VIDEO CAMERA RECORDER. SERVICE MANUAL VERSION 1.1 2008.11
PART#(9-852-601-32)
Back to : SONY HDR-CX11E, CX12, CX1 | Home
HDR-CX11E/CX12/CX12E RMT-835
SERVICE MANUAL LEVEL 2
US Model
Ver. 1.1 2008.11 Canadian Model
Revision History AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
Photo: HDR-CX12
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS
SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST
· Precaution on Replacing the VC-535 Board
· Precaution on Replacing the Holder (MS)
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
2008K0800-1
HDR-CX11E/CX12/CX12E_L2 © 2008.11
9-852-601-32 Sony EMCS Co. Published by Kohda TEC
These specifications are extracted from instruction manual of
HDR-CX11E/CX12E.
ENGLISH JAPANESE
SPECIFICATIONS
System General Rechargeable battery pack
Video compression format: AVCHD (HD)/ Power requirements: DC 6.8 V/7.2 V (battery NP-FH60
MPEG2 (SD)/JPEG (Still images) pack) Maximum output voltage: DC 8.4 V
Audio compression format: Dolby Digital 2/5.1ch DC 8.4 V (AC Adaptor) Output voltage: DC 7.2 V
Dolby Digital 5.1 Creator Average power consumption: During camera
Capacity: 7.2 wh (1 000 mAh)
recording using the LCD with normal
Video signal: PAL color, CCIR standards
brightness: Type: Li-ion
1080/50i specification
HD: 3.8 W SD: 3.3 W
Recording format: Movie (HD): AVCHD Design and specifications of your camcorder and
Operating temperature: 0°C to 40°C (32 °F to
1080/50i accessories are subject to change without notice.
104 °F)
Movie (SD): MPEG2-PS Manufactured under license from Dolby
Still image: Exif Ver.2.2* Storage temperature: -20°C to + 60°C (-4 °F to
+ 140 °F) Laboratories.
Image device: 5.8 mm (1/3.13 type) CMOS sensor
Recording pixels (still image, 4:3): Dimensions (approx.): 69 × 67 × 129 mm (2 3/4 ×
Max. 10.2 mega (3 680 × 2 760) pixels** 2 3/4 × 5 1/8 in.) (w×h×d)
Gross: Approx. 5 660 000 pixels including the projecting parts
Effective (Movie, 16:9): 69 × 67 × 131 mm (2 3/4 × 2 3/4 × 5 1/4 in.)
Approx. 3 810 000 pixels (w×h×d)
Effective (still image, 16:9): including the projecting parts, and the
Approx. 3 810 000 pixels supplied battery pack attached
Effective (still image, 4:3): Mass (approx.): 370 g (13 oz)
Approx. 5 080 000 pixels main unit only
Lens: Carl Zeiss Vario-Sonnar T 450 g (1 lb) including the supplied
12 × (Optical), 24 ×, 150 × (Digital) rechargeable battery pack
Focal length: F=1.8 - 3.1
Filter diameter: 37 mm (1 1/2 in.) Handycam Station DCRA-C240
f=4.9 - 58.8 mm (7/32- 2 3/8 in.)
When converted to a 35 mm still camera Input/Output connector
For movies: 40 - 480 mm (1 5/8 - 19 in.)
(16:9) A/V OUT jack: Component/video and audio
For still images: 37 - 444 mm (1 1/2 - 17 1/2 output jack
in.) (4:3) USB jack: mini-B
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR] AC Adaptor AC-L200/L200B
(5 800 K)
Power requirements: AC 100 V - 240 V, 50 Hz/60
Minimum illumination: 5 lx (lux) ([AUTO SLW Hz
SHUTTR] [ON], Shutter speed 1/25 second)
Current consumption: 0.35A - 0.18A
0 lx (lux) (during NightShot function)
Power consumption: 18 W
* "Exif" is a file format for still images,
established by the JEITA (Japan Electronics Output voltage: DC 8.4 V*
and Information Technology Industries
Association). Files in this format can Operating temperature: 0°C to 40°C (32 °F to
have additional information such as your 104 °F)
camcorder's setting information at the time of Storage temperature: -20°C to + 60°C (-4 °F to
recording. + 140 °F)
**The unique pixel array of Sony's ClearVid Dimensions (approx.): 48 × 29 × 81 mm (1 15/16
CMOS Sensor and image processing system × 1 3/16 × 3 1/4 in.)(w×h×d)
(BIONZ) allows still image resolution excluding the projecting parts
equivalent to the sizes described.
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
Input/Output connectors * See the label of AC Adaptor for other
specifications.
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini connector
LCD screen
Image: 6.7 cm (2.7 type, aspect ratio 16:9)
Total dot number: 211 200 (960 × 220)
HDR-CX11E/CX12/CX12E_L2
--2--
These specifications are extracted from instruction manual of
HDR-CX12.
ENGLISH JAPANESE
SPECIFICATIONS
System General Rechargeable battery pack
Video compression format: AVCHD (HD)/ Power requirements: DC 6.8 V/7.2 V (battery NP-FH60
MPEG2 (SD)/JPEG (Still images) pack) Maximum output voltage: DC 8.4 V
Audio compression format: Dolby Digital 2/5.1ch DC 8.4 V (AC Adaptor) Output voltage: DC 7.2 V
Dolby Digital 5.1 Creator Average power consumption: During camera
Capacity: 7.2 wh (1 000 mAh)
recording using the LCD with normal
Video signal: NTSC color, EIA standards
brightness: Type: Li-ion
1080/60i specification
HD: 4.1 W SD: 3.3 W
Recording format: Movie (HD): AVCHD Design and specifications of your camcorder and
Operating temperature: 0°C to 40°C (32 °F to
1080/60i accessories are subject to change without notice.
104 °F)
MOVIE (SD): MPEG2-PS
Still image:Exif Ver.2.2* Storage temperature: -20°C to + 60°C (-4 °F to Manufactured under license from Dolby
+ 140 °F) Laboratories.
Image device: 5.8 mm (1/3.13 type) CMOS sensor
Recording pixels (still image, 4:3): Dimensions (Approx.): 69 × 67 × 129 mm (2 3/4
Max. 10.2 mega (3 680 × 2 760) pixels** × 2 3/4 × 5 1/8 in.)
Gross: Approx. 5 660 000 pixels (w×h×d) including the projecting parts
Effective (Movie, 16:9) 69 × 67 × 131 mm (2 3/4 × 2 3/4 × 5 1/4 in.)
Approx. 3 810 000 pixels (w×h×d) including the projecting parts, and
Effective (Still image, 16:9) the supplied battery pack attached
Approx. 3 810 000 pixels Mass (Approx.): 370 g (13 oz) main unit only
Effective (Still image, 4:3)
450 g (1 lb) including the supplied
Approx. 5 080 000 pixels
rechargeable battery pack
Lens: Carl Zeiss Vario-Sonnar T
12 × (Optical), 24 ×, 150 × (Digital) Handycam Station DCRA-C240
Focal length: F=1.8 - 3.1
Filter diameter: 37 mm (1 1/2 in) Input/Output connector
f=4.9 - 58.8 mm (7/32 - 2 3/8 in.)
When converted to a 35 mm still camera A/V OUT jack: Component/video and audio
For movies: 40 - 480 mm (1 5/8 - 19 in.) output jack
(16:9) USB jack: mini-B
For still images: 37 - 444 mm (1 1/2 - 17 1/2
in.) (4:3)
Color temperature: [AUTO], [ONE PUSH],
AC Adaptor AC-L200/L200B
[INDOOR] (3 200 K), [OUTDOOR] Power requirements: AC 100 V - 240 V, 50 Hz/60
(5 800 K) Hz
Minimum illumination: 5 lx (lux) ([AUTO SLW Current consumption: 0.35A - 0.18A
SHUTTR] [ON], Shutter speed 1/30 second) Power consumption: 18 W
0 lx (lux) (during NightShot function)
Output voltage: DC 8.4 V*
* "Exif" is a file format for still images,
established by the JEITA (Japan Electronics Operating temperature: 0°C to 40°C (32 °F to
and Information Technology Industries 104 °F)
Association). Files in this format can Storage temperature: -20°C to + 60°C (-4 °F to
have additional information such as your + 140 °F)
camcorder's setting information at the time of Dimensions (Approx.): 48 × 29 × 81 mm (1 15/16
recording. × 1 3/16 × 3 1/4 in.)(w×h×d)
**The unique pixel array of Sony's ClearVid excluding the projecting parts
CMOS Sensor and image processing system Mass (approx.): 170 g (6.0 oz) excluding the
(BIONZ) allows still image resolution power cord (mains lead)
equivalent to the sizes described.
* See the label of AC Adaptor for other
specifications.
Input/Output connectors
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini connector
LCD screen
Image: 6.7 cm (2.7 type, aspect ratio 16:9)
Totaldot number: 211 200 (960 × 220)
HDR-CX11E/CX12/CX12E_L2
--3--
ENGLISH JAPANESE
*
* *
**
*
**
HDR-CX11E/CX12/CX12E_L2
--4--
Model information table
Model HDR-CX11E HDR-CX12 HDR-CX12E
US, CND, E, KR, NE, CH, AUS, HK,
Destination AEP, UK, NE
JE, J E, JE
Color system PAL NTSC PAL
Data CAM PC
copy CAM PC
Supplied accessory 4 GB : EXCEPT J
4 GB 4 GB
"Memory Stick PRO Duo" 8 GB : J
· Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-CX11E/CX12/CX12E_L2
--5--
ENGLISH JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. · Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
· Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
· Strong viscosity
· Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
· Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. · Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-CX11E/CX12/CX12E_L2
--6--
ENGLISH JAPANESE
1. 6.
· 270
·
·
2. 7.
Lead Free
0
3.
· 40
4. 350
·
5. IC
·
· ·
HDR-CX11E/CX12/CX12E_L2
--7--
1. SERVICE NOTE ENGLISH JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function 1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
function starts working, and displays on the LCD screen what to LCD screen shows a 4-digit display consisting of an alphabet and
do. This function consists of two display; self-diagnosis display and numbers, which blinks at 3.2 Hz. This 5-character display indicates
service mode display. the "repaired by:", "block" in which the problem occurred, and
Details of the self-diagnosis functions are provided in the Instruction "detailed code" of the problem.
manual.
LCD screen
C:31:11
Blinks at 3.2Hz
C 31 11
Repaired by: Block Detailed Code
C : Corrected by customer Indicates the appropriate Refer to "1-2-3. Self-diagnosis Code Table".
H : Corrected by dealer step to be taken.
E : Corrected by service E.g.
engineer 31 ....Reload the tape.
32 ....Turn on power again.
HDR-CX11E/CX12/CX12E_L2
1-1
ENGLISH JAPANESE
1-2-3. Self-diagnosis Code Table
Self-diagnosis Code
Repaired by:
Block Detailed Symptom/State Correction
Function Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
"Memory Stick Duo" is unformatted. Format the "Memory Stick Duo".
C 1 3 0 1
"Memory Stick Duo" is broken. Insert a new "Memory Stick Duo".
Remove the power source. Reconnect it again and operate your
C 1 3 0 2 Media access error
camcorder again
Retry turn the power on by the power switch. If it does not
Difficult to adjust focus recover, check the focus MR sensor of lens block (pin w;, wa of
C 3 2 6 0
(Cannot initialize focus) CN5101 on the LD-241 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-241 board).
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
Inspect the lens block zoom MR sensor (pin qh, qj of CN5101
Zoom operations fault on the LD-241 board) when zooming is performed when the
E 6 1 1 0 (Cannot initialize zoom lens.) zoom lever is operated, and the zoom motor drive circuit
(IC5201 on the LD-241 board) when zooming is not performed.
The abnormalities in initialization of
the focus lens and the abnormalities in
E 6 1 1 1 Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
E 6 2 0 0 work well. (With PITCH angular Inspect PITCH angular velocity sensors (SE9001 on the LD-241
velocity sensor output stopped.) board) peripheral circuits.
Handshake correction function does not
E 6 2 0 1 work well. (With YAW angular velocity Inspect YAW angular velocity sensors (SE1001 on the VC-535
sensor output stopped.) board) peripheral circuits.
Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
E 6 2 0 2 Abnormality of IC for steadyshot.
Occurred].
IC for steadyshot and micro controller
E 6 2 0 3 Inspect the steadyshot circuit (IC5501 on the LD-241 board).
communication abnormality among.
Replacement of lens block. If an error occurs again, replace the
E 6 2 1 0 Shift lens initializing failure.
LD-241 board. (Note 2)
Shift lens overheating (Pitch) Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
E 6 2 1 1
Occurred].
Shift lens overheating (Yaw) Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
E 6 2 1 2
Occurred].
Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor)
E 6 2 2 0 Abnormality of thermistor.
Occurred].
E 9 1 0 1 Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit.
Fault of writing or erasing the
E 9 4 0 0 Inspect the flash memory (IC2101 on the VC-535 board).
flash memory
Note 1 : Refer to Service Manual, ADJ ("1-3. DESTINATION DATA WRITE").
Note 2 : When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX11E/CX12/CX12E_L2
1-2
ENGLISH JAPANESE
1-3. METHOD OF COPING WITH SHIFT LENS ERROR
about 330 msec
Note: The length of low section will vary a little depending on the
conditions.
Fig. 2
Change in output voltage of R5549 on the LD-241 board
LD-241 BOARD (SIDE B) VC-535 BOARD (SIDE A)
R5526
IC5501
IC1301
R5549
R5534
Fig. 1
Measurement points on the LD-241 board and the VC-535 board
1-3-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order Procedure
1 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501 on the LD-241 board, turn the
2
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
3
the camera control circuit (IC1301 of VC-535 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX11E/CX12/CX12E_L2
1-3
ENGLISH JAPANESE
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data Procedure
1 11 80 7430 01 Write the data. (After it starts, set it before caution is displayed.)
2 11 8E F946 F0 Write the data.
3 11 8E F948 01 Write the data. (Note 1)
4 11 8E F948 00 Write the data.
5 11 8E F946 10 Write the data.
6 11 8E F948 01 Write the data. (Note 1)
7 11 8E F948 00 Write the data.
8 11 80 7430 00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
9
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5526 in the
10
periphery of IC5501 on the LD-241 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
11
varied, proceed to the order 12.
12 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
13 on the LD-241 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14 change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-535 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F948, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX11E/CX12/CX12E_L2
1-4
ENGLISH JAPANESE
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data Procedure
1 11 80 7430 01 Write the data. (After it starts, set it before caution is displayed.)
2 11 8E F947 F0 Write the data.
3 11 8E F949 01 Write the data. (Note 1)
4 11 8E F949 00 Write the data.
5 11 8E F947 10 Write the data.
6 11 8E F949 01 Write the data. (Note 1)
7 11 8E F949 00 Write the data.
8 11 80 7430 00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
9
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5534 in the
10
periphery of IC5501 on the LD-241 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
11
varied, proceed to the order 12.
12 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
13 on the LD-241 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14 change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-535 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F949, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order Procedure
1 Turn the power ON.
Confirm the connections of flexible flat cables and connectors between the lens block and LD-241 board, LD-241 board and
2
VC-535 board.
In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of
3
the lens replacement, replace LD-241 board with new one.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX11E/CX12/CX12E_L2
1-5
ENGLISH JAPANESE
1-4. PRECAUTION ON REPLACING THE VC-535 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform "DESTINATION DATA WRITE".
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform "USB SERIAL No. INPUT".
About the PITCH/YAW Sensor Data
The PITCH data the PITCH sensor (SE9001) on LD-241 board uses is saved in the memory on VC-535 board.
Therefore, in case of replacing VC-535 board, the data for the PITCH sensor (SE9001) on LD-241 board is lost.
On replacing VC-535 board, cope with one procedure as following mentioned.
· Replace VC-535 and LD-241 boards at the same time.
· Replace VC-535 board and the PITCH sensor (SE9001) on LD-241 board at the same time.
HDR-CX11E/CX12/CX12E_L2
1-6
1. SERVICE NOTE ENGLISH JAPANESE
1-1.
8.4Vdc 10
DC AC AC-L200/L200B
1-2.
1-2-1. 1-2-2.
LCD
LCD 4 3.2Hz
5
LCD
C:31:11
3.2Hz
C 31 11
C 1-2-3.
H 31
E 32
HDR-CX11E/CX12/CX12E_L2
1-7
ENGLISH JAPANESE
C 0 4 0 0
C 1 3 0 1
C 1 3 0 2
C 3 2 6 0
w; wa
E 2 0 0 0
E 6 1 1 0
qh
qj
E 6 1 1 1
E 6 2 0 0
E 6 2 0 1
E 6 2 0 2
E 6 2 0 3
E 6 2 1 0
E 6 2 1 1
E 9 1 0 1
E 9 4 0 0
HDR-CX11E/CX12/CX12E_L2
1-8
ENGLISH JAPANESE
LD-241 BOARD (SIDE B) VC-535 BOARD (SIDE A)
R5526
IC5501
IC1301
R5549
R5534
HDR-CX11E/CX12/CX12E_L2
1-9
ENGLISH JAPANESE
1 11 80 7430 01
2 11 8E F946 F0
3 11 8E F948 01 1
4 11 8E F948 00
5 11 8E F946 10
6 11 8E F948 01 1
7 11 8E F948 00
8 11 80 7430 00
2 7
9 2
10
HDR-CX11E/CX12/CX12E_L2
1-10
ENGLISH JAPANESE
1 11 80 7430 01
2 11 8E F947 F0
3 11 8E F949 01 1
4 11 8E F949 00
5 11 8E F947 10
6 11 8E F949 01 1
7 11 8E F949 00
8 11 80 7430 00
2 7
9 2 10
HDR-CX11E/CX12/CX12E_L2
1-11
ENGLISH JAPANESE
1-4. VC-535
ADJ DESTINATION DATA WRITE
USB No.
1 ID USB Serial No.
ID ID
ADJ USB SERIAL No. INPUT
PITCH/YAW
LD-241 PITCH (SE9001) PITCH VC-535
VC-535 LD-241 PITCH (SE9001)
VC-535
· VC-535 LD-241
· VC-535 LD-241 PITCH (SE9001)
HDR-CX11E/CX12/CX12E_L2
1-12
(ENGLISH) HDR-CX11E (AEP, UK Models)
1-5. PRECAUTION ON REPLACING
THE HOLDER (MS)
(HDR-CX11E)
The model display adopts the laser printing method.Therefore, the
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the holder (MS) , the serial number for it
Serial No.
will be changed to the one exclusive for service use. Part No. Description
Inform a customer of the serial number change and change the serial A-1556-668-A HOLDER (CX11E-CEH),(MS)
number in the repair data.
HDR-CX11E (North European Model)
(JAPANESE)
1-5. (MS)
(HDR-CX11E)
(MS)
Part No. Description Serial No.
A-1556-669-A HOLDER (CX11E-CEL),(MS)
1: (MS)
HDR-CX11E/CX12/CX12E_L2
1-13
(ENGLISH) HDR-CX12 (Japanese Model)
* Affix the label
1-6. PRECAUTION ON REPLACING
THE HOLDER (MS) Serial No.
(HDR-CX12)
The model display adopts the laser printing method.Therefore, the
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order. * Manufacturing year
Part No. Description
A-1556-656-A HOLDER (CX12-J1), (MS)
Note1: After replacing the holder (MS), the serial number for it
will be changed to the one exclusive for service use. HDR-CX12 (US Model)
* Affix the label
Inform a customer of the serial number change and change the serial
number in the repair data. Serial No.
Note 2: When replacing the holder (MS) for US, affix the
"Manufacturing year" label and the "Factory" label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the holder (MS). * Factory
* Manufacturingyear
Part No. Description
Note 3: When replacing the holder (MS) for Korea and Japanese, A-1556-658-A HOLDER (CX12-U2), (MS)
affix the "Manufacturing year" label on the specified location as
shown in the figure. HDR-CX12 (Canadian Model)
The replacement caution label and inset (how to affix) are supplied
together with the holder (MS).
Serial No.
(JAPANESE)
1-6. (MS) Part No. Description
(HDR-CX12) A-1556-659-A HOLDER (CX12-CA2),(MS)
HDR-CX12 (E Model)
(MS)
1: (MS)
Serial No.
Part No. Description
A-1556-660-A HOLDER (CX12-E23),(MS)
HDR-CX12 (Korea Model) * Affix the label
Serial No.
2: US (MS)
(MS) (
)
* Manufacturing year
Part No. Description
3: Korean Japanese (MS) A-1556-661-A HOLDER (CX12-KR2),(MS)
HDR-CX12 (Tourist Model)
(MS) (
)
Serial No.
Part No. Description
A-1556-662-A HOLDER (CX12-JE3),(MS)
HDR-CX11E/CX12/CX12E_L2
1-14
(ENGLISH) HDR-CX12E (North European Model)
1-7. PRECAUTION ON REPLACING
THE HOLDER (MS)
(HDR-CX12E)
The model display adopts the laser printing method.Therefore, the
holder (MS) for replacement differs depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the holder (MS) , the serial number for it Serial No.
will be changed to the one exclusive for service use. Part No. Description
Inform a customer of the serial number change and change the serial A-1556-667-A HOLDER (CX12E-CEL),(MS)
number in the repair data.
HDR-CX12E (E, Hong Kong, Australian Models)
(JAPANESE)
1-7. (MS)
(HDR-CX12E)
(MS)
Serial No.
Part No. Description
A-1556-663-A HOLDER (CX12E-E34),(MS)
1: (MS)
HDR-CX12E (Chinese Model)
Serial No.
Part No. Description
A-1556-664-A HOLDER (CX12E-CN2),(MS)
HDR-CX12E (Tourist Model)
Serial No.
Part No. Description
A-1556-666-A HOLDER (CX12E-JE3),(MS)
HDR-CX11E/CX12/CX12E_L2
1-15E
2. DISASSEMBLY
NOTE FOR REPAIR
· Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt
Do not insert the cable insufficiently nor crookedly. which comes off at the point.
(Be careful or some
· When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside)
· When installing a connector, don't press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF THE ST-201 BOARD'S CHARGING CAPACITOR (C5206)
The charging capacitor (C5206) of the ST-201 board is charged Note: High-voltage cautions
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the Discharging the Capacitor
Short-circuit between the two points with
capacitor is handled by hand. The electric shock is caused by the short jig about 10 seconds.
the charged voltage which is kept without discharging when the To avoid the spark with the metal plate,
main power of the unit is simply turned off. Therefore, the wrap the short jig with the insulation tape.
remaining voltage must be discharged as described below.
R:1 k/1 W
Preparing the Short Jig (Part code: 1-215-869-11)
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k /1 W (1-215-869-11). ST-201 Board
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1 k/1 W
Wrap insulating tape.
Elect Cap
70uF 330V
(C5206)
ST-201 Board
NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE)
When disconnecting the harness (COAXIAL CABLE), do not
pull the harness part but pull off the connector body with tweezers
etc.
Harness
(coaxial cable)
Tweezers etc.
HDR-CX11E/CX12/CX12E_L2
2-1
2-1. IDENTIFYING PARTS
Cabinet L Section Top Cabinet Section BT Panel Section
PH-003 Board CR-092 Board
Lens Section
LD-241 Board
CM-094 Board
VC-535 Board
Cabinet R Section
CK-203 Board
Flash Unit Section
ST-201 Board
LCD Panel Section
PD-371 Board
Front Panel Section
MS-402 Board Section
MS-402 Board
- DISASSEMBLY FLOW -
2-2-1. OVERALL SECTION
- LCD Panel Section
- Front Panel Section
2-2-4. MAIN BODY SECTION 2-2-2. LCD PANEL SECTION
- Top Cabinet Section - LCD Panel Section
- MS-402 Board Section
- Cabinet L Section
2-2-5. LENS/BT SECTION 2-2-3. CABINET R SECTION
- VC-535 Board Block - Hinge Block
- BT Panel Section - CK-203 Board
- ST-201 Board Block - Loud Speaker (SP901)
HDR-CX11E/CX12/CX12E_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1 LCD Panel Section (1-1 to 1-15)
2 Front Panel Section (2-1 to 2-10)
Main Body Section
(See Page 2-6)
HELP01
1 LCD Panel
2 Front Panel Section
Section (See Page 2-4) 1-8
(#2)
1-7
2-2 2-9 (Open)
1-10
(Claw) (#2) (#2)
1-14 1-13
(Claw)
2-10
2-8 (#2) 1-15
1-1
2-3 2-6
(Open)
2-4 1-2
2-5 (#1/#14)
1-4 1-6
(Claw) 1-9 (#2)
(#2)
1-5
1-3
1-12 (#2) 1-11 (#2)
2-1 (#2/#10) 2-7 (#2)
HDR-CX11E/CX12/CX12E_L2
2-3
2-2-2. LCD PANEL SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 LCD Panel Section (1-1 to 1-9)
1-3
(#2/#10) Cabinet R Section
(See Page 2-5)
1-2
A
(#2/#10)
HELP02
HELP02
1-6 (Claw)
1-7 (Claw)
C
1-9
1-8 A
1-4
(Claw)
1-5
1-1 B
(#2/#10)
C PD
-3
71
B
1 LCD Panel Section
HDR-CX11E/CX12/CX12E_L2
2-4
2-2-3. CABINET R SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Hinge Block (1-1 to 1-3)
2 CK-203 Board (2-1 to 2-6)
3 Loud Speaker (SP901) (3-1 to 3-2)
2-1 (#3)
2-2
HELP03 2 CK-203 Board
2-4
Note: On installation of the CK-203 board,
adjust the position of the "NIGHTSHOT"
switch and the "NIGHTSHOT" nob.
2-3
HELP04
3 3 Loud
- 20 3-1 (#3)
CK 3-2 Speaker
2-6 (#3)
(SP901)
2-5
1-1
1-2
HELP05
1-3 (#2)
1 Hinge Block
HDR-CX11E/CX12/CX12E_L2
2-5
2-2-4. MAIN BODY SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Top Cabinet Section (1-1 to 1-5)
2 MS-402 Board Section (2-1 to 2-3)
3 Cabinet L Section (3-1 to 3-5)
Note: High-voltage cautions
R:1 k/1 W
(Part code: 1-215-869-11)
Discharging the Capacitor
Short-circuit between the two points with
the short jig about 10 seconds. C5206 ST-201 Board
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
1-3 (#2) HELP06
3-3 1 Top Cabinet Section
(#11) Note: Don't touch the grease
spreading part.
1-1
(#2)
3-4
(#2)
1-5 Lens/BT Section
3-5 (Claw) (See Page 2-7)