Text preview for : SONY HDR-SR11, SR11E, SR12, SR12E SERVICE MANUAL LEVEL 2 VER 1.4 2009.03 (9-852-254-35).pdf part of SONY HDR-SR11 SONY HDR-SR11, SR11E, SR12, SR12E
DIGITAL HD VIDEO CAMERA RECORDER. SERVICE MANUAL VERSION 1.4 2009.03
PART#(9-852-254-35)
Back to : SONY HDR-SR11, SR11E, SR1 | Home
HDR-SR11/SR11E/SR12/SR12E RMT-835
SERVICE MANUAL LEVEL 2
US Model
Ver. 1.4 2009.03 Canadian Model
Revision History AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Thai Model
Photo: HDR-SR12 Japanese Model
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS
SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST
· Precaution on Replacing the VC-516 Board
· Precaution on Replacing the CABINET (G(900)) ASSY
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
2009C0800-1
HDR-SR11/SR11E/SR12/SR12E_L2 © 2009.03
9-852-254-32 Sony EMCS Co. Published by Kohda TEC
These specifications are extracted from instruction manual of
HDR-SR11E/SR12E.
ENGLISH JAPANESE
SPECIFICATIONS
System Input/Output connectors Handycam Station DCRA-C210
Video compression format: AVCHD (HD)/ A/V Remote Connector: Component/video and
MPEG2 (SD)/JPEG (Still images) audio output jack Input/Output connectors
Audio compression format: Dolby Digital 2/5.1ch HDMI OUT jack: HDMI Type C mini connector A/V OUT jack: Component/video and audio
Dolby Digital 5.1 Creator Headphone jack: Stereo minijack ( 3.5mm) output jack
Video signal: PAL color, CCIR standards MIC input jack: Stereo minijack ( 3.5mm) USB jack: mini-B
1080/50i specification USB jack: mini-B AC Adaptor AC-L200/L200B
Hard disk: HDR-SR11E: 60 GB
HDR-SR12E: 120 GB LCD screen Power requirements: AC 100 V - 240 V, 50/60 Hz
When measuring media capacity, 1 GB equals Image: 8.0 cm (3.2 type, aspect ratio 16:9) Current consumption: 0.35 - 0.18 A
1 billion bytes, a portion of which is used for Power consumption: 18 W
Total dot number: 921 600 (1 920 × 480)
data management. Output voltage: DC 8.4 V*
Recording format: Movie (HD): AVCHD 1080/ General Operating temperature: 0 °C to + 40 °C (32 °F to
50i Power requirements: DC 6.8 V/7.2 V (battery 104 °F)
Movie (SD): MPEG2-PS pack) Storage temperature: -20 °C to + 60 °C (-4 °F to +
Still image: Exif Ver.2.2* DC 8.4 V (AC Adaptor) 140 °F)
Viewfinder: Electric viewfinder: color Average power consumption: During camera Dimensions (approx.): 48 × 29 × 81 mm
Image device: 5.8 mm (1/3.13 type) CMOS sensor recording using the viewfinder with normal (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
Recording pixels (still image, 4:3): brightness: excluding the projecting parts
Max. 10.2 mega (3 680 × 2 760) pixels** Hard disk: Mass (approx.): 170 g (6.0 oz) excluding the
Gross: Approx. 5 660 000 pixels HD: 4.2 W SD: 3.6 W power cord (mains lead)
Effective (movie, 16:9): "Memory Stick PRO Duo":
Approx. 3 810 000 pixels HD: 4.2 W SD: 3.5 W * See the label on the AC Adaptor for other
Effective (still image, 16:9): During camera recording using the LCD with specifications.
Approx. 3 810 000 pixels normal brightness:
Effective (still image, 4:3): Hard disk: Rechargeable battery pack NP-FH60
Approx. 5 080 000 pixels HD: 4.5 W SD: 3.8 W Maximum output voltage: DC 8.4 V
Lens: Carl Zeiss Vario-Sonnar T "Memory Stick PRO Duo": Output voltage: DC 7.2 V
12 × (Optical), 24 ×, 150 × (Digital) HD: 4.5 W SD: 3.8 W Capacity: 7.2 Wh (1 000 mAh)
Focal length: F1.8 ~ 3.1 Operating temperature: 0 °C to + 40 °C (32 °F to Type: Li-ion
Filter diameter: 37 mm (1 1/2 in.) 104 °F)
f=4.9 ~ 58.8 mm (7/32 ~ 2 3/8 in.) Storage temperature: -20 °C to + 60 °C (-4 °F to + Design and specifications of your camcorder and
When converted to a 35 mm still camera 140 °F) accessories are subject to change without notice.
For movies: 40 ~ 480 mm (1 5/8 ~ 19 in.) Dimensions (approx.): 83 × 76 × 138 mm
(16:9) (3 3/8 × 3 × 5 1/2 in.) (w/h/d)
For still images: 37 ~ 444 mm (1 1/2 ~ 17 1/2 including the projecting parts
in.) (4:3) 83 × 76 × 138 mm
Color temperature: [AUTO], [ONE PUSH], (3 3/8 × 3 × 5 1/2 in.) (w/h/d)
[INDOOR] (3 200 K), including the projecting parts, and the supplied
[OUTDOOR] (5 800 K) rechargeable battery pack attached
Minimum illumination: 5 lx (lux) ([AUTO SLW Mass (approx.): HDR-SR11E: 560 g (1 lb 3 oz)
SHUTTR] [ON], Shutter speed 1/25 sec) main unit only
0 lx (lux) (during NightShot function) 640 g (1 lb 6 oz) including the supplied
* "Exif" is a file format for still images, rechargeable battery pack
established by the JEITA (Japan HDR-SR12E: 570 g (1 lb 4 oz) main unit only
Electronics and Information Technology 650 g (1 lb 6 oz) including the supplied
Industries Association). Files in this rechargeable battery pack
format can have additional information
such as your camcorder's setting
information at the time of recording.
** The unique pixel array of Sony's ClearVid
CMOS sensor and image processing
system (BIONZ) allows for still image
resolution equivalent to the sizes
described.
HDR-SR11/SR11E/SR12/SR12E_L2
--2--
These specifications are extracted from instruction manual of
HDR-SR11/SR12.
ENGLISH JAPANESE
SPECIFICATIONS
System Input/Output connectors Handycam Station DCRA-C210
Video compression format: AVCHD (HD)/ A/V Remote Connector: Component/video and
MPEG2 (SD)/JPEG (Still images) audio output jack Input/Output connectors
Audio compression format: Dolby Digital 2/5.1ch HDMI OUT jack: HDMI Type C mini connector A/V OUT jack: Component/video and audio
Dolby Digital 5.1 Creator Headphone jack: Stereo minijack ( 3.5mm) output jack
Video signal: NTSC color, EIA standards MIC input jack: Stereo minijack ( 3.5mm) USB jack: mini-B
1080/60i specification USB jack: mini-B AC Adaptor AC-L200/L200B
Hard disk: HDR-SR11: 60 GB
HDR-SR12: 120 GB LCD screen Power requirements: AC 100 V - 240 V, 50/60 Hz
When measuring media capacity, 1 GB equals Image: 8.0 cm (3.2 type, aspect ratio 16:9) Current consumption: 0.35 - 0.18 A
1 billion bytes, a portion of which is used for Power consumption: 18 W
Total dot number: 921 600 (1 920 × 480)
data management. Output voltage: DC 8.4 V*
Recording format: Movie (HD): AVCHD 1080/ General Operating temperature: 0 °C to + 40 °C (32 °F to
60i Power requirements: DC 6.8 V/7.2 V (battery 104 °F)
Movie (SD): MPEG2-PS pack) Storage temperature: -20 °C to + 60 °C (-4 °F to +
Still image: Exif Ver.2.2* DC 8.4 V (AC Adaptor) 140 °F)
Viewfinder: Electric viewfinder: color Average power consumption: During camera Dimensions (approx.): 48 × 29 × 81 mm
Image device: 5.8 mm (1/3.13 type) CMOS sensor recording using the viewfinder with normal (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
Recording pixels (still image, 4:3): brightness: excluding the projecting parts
Max. 10.2 mega (3 680 × 2 760) pixels** Hard disk: Mass (approx.): 170 g (6.0 oz) excluding the
Gross: Approx. 5 660 000 pixels HD: 4.5 W SD: 3.6 W power cord (mains lead)
Effective (movie, 16:9): "Memory Stick PRO Duo":
Approx. 3 810 000 pixels HD: 4.4 W SD: 3.6 W * See the label on the AC Adaptor for other
Effective (still image, 16:9): During camera recording using the LCD with specifications.
Approx. 3 810 000 pixels normal brightness:
Effective (still image, 4:3): Hard disk: Rechargeable battery pack NP-FH60
Approx. 5 080 000 pixels HD: 4.8 W SD: 4.0 W Maximum output voltage: DC 8.4 V
Lens: Carl Zeiss Vario-Sonnar T "Memory Stick PRO Duo": Output voltage: DC 7.2 V
12 × (Optical), 24 ×, 150 × (Digital) HD: 4.6 W SD: 3.9 W Capacity: 7.2 Wh (1 000 mAh)
Focal length: F1.8 ~ 3.1 Operating temperature: 0 °C to + 40 °C (32 °F to Type: Li-ion
Filter diameter: 37 mm (1 1/2 in.) 104 °F)
f=4.9 ~ 58.8 mm (7/32 ~ 2 3/8 in.) Storage temperature: -20 °C to + 60 °C (-4 °F to + Design and specifications of your camcorder and
When converted to a 35 mm still camera 140 °F) accessories are subject to change without notice.
For movies: 40 ~ 480 mm (1 5/8 ~ 19 in.) Dimensions (approx.): 83 × 76 × 138 mm
(16:9) (3 3/8 × 3 × 5 1/2 in.) (w/h/d)
For still images: 37 ~ 444 mm (1 1/2 ~ 17 1/2 including the projecting parts
in.) (4:3) 83 × 76 × 138 mm
Color temperature: [AUTO], [ONE PUSH], (3 3/8 × 3 × 5 1/2 in.) (w/h/d)
[INDOOR] (3 200 K), including the projecting parts, and the supplied
[OUTDOOR] (5 800 K) rechargeable battery pack attached
Minimum illumination: 5 lx (lux) ([AUTO SLW
Mass (approx.): HDR-SR11: 560 g (1 lb 3 oz)
SHUTTR] [ON], Shutter speed 1/30 sec)
main unit only
0 lx (lux) (during NightShot function)
640 g (1 lb 6 oz) including the supplied
* "Exif" is a file format for still images, rechargeable battery pack
established by the JEITA (Japan HDR-SR12: 570 g (1 lb 4 oz) main unit only
Electronics and Information Technology 650 g (1 lb 6 oz) including the supplied
Industries Association). Files in this rechargeable battery pack
format can have additional information
such as your camcorder's setting
information at the time of recording.
** The unique pixel array of Sony's ClearVid
CMOS sensor and image processing
system (BIONZ) allows for still image
resolution equivalent to the sizes
described.
HDR-SR11/SR11E/SR12/SR12E_L2
--3--
ENGLISH JAPANESE
/ AC AC-L200/L200B
AVCHD HD /MPEG2 SD /JPEG A/V AC 100 V - 240 V 50/60 Hz
18 W
Dolby Digital2/5.1ch HDMI OUT HDMI C DC 8.4 V *
5.1 ¯ 3.5 mm 0 +40
NTSC EIA MIC ¯ 3. 5 mm 20 +60
1080/60i
USB mini-B 48 29 81 mm
HDR-SR11 60 GB
HDR-SR12 120 GB
1GB 10 170 g
8.0 cm 3.2 16 9
* AC
921 600
1 920 480
HD AVCHD 1080/60i
SD MPEG2-PS NP-FH60
Exif Ver.2.2* 6.8 V/7.2 V DC 8.4 V
DC 8.4 V
DC 7.2 V
5.8 mm 1/3.13 CMOS 7.2 Wh 1 000 mAh
1 020 ** Li-ion
3 680 2 760 4 3 HD 4.5 W SD 3.6 W
566 PRO
16 9 381 HD 4.4 W SD 3.6 W
16 9 381
4 3 508
HD 4.8 W SD 4.0 W
T PRO
12 24 150 HD 4.6 W SD 3.9 W
37 mm
F1.8 3.1 0 +40
f=4.9 58.8 mm 20 +60
35mm 83 76 138 mm
40 480 mm 16 9
37 444 mm 4 3 83 76 138 mm
3 200 K 5 800 K
5 lx HDR-SR11 560 g
1/30 HDR-SR12 570 g
0 lx NightShot HDR-SR11 640 g
* JEITA
HDR-SR12 650 g
** CMOS DCRA-C210
BIONZ
/
A/V OUT
USB mini-B
HDR-SR11/SR11E/SR12/SR12E_L2
--4--
Model information table
Model HDR-SR11 HDR-SR11E HDR-SR12 HDR-SR12E
AEP, UK, NE, E, AEP, UK, NE, E,
Destination US, CND, E, KR, JE, J US, CND, E, KR, JE, J
CH, HK, AUS, JE CH, HK, AUS, JE
Color system NTSC PAL NTSC PAL
Hard disk 60GB 60GB 120GB 120GB
· Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-SR11/SR11E/SR12/SR12E_L2
--5--
ENGLISH JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. · Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
· Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
· Strong viscosity
· Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
· Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. · Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-SR11/SR11E/SR12/SR12E_L2
--6--
ENGLISH JAPANESE
1. 6.
· 270
·
·
2. 7.
Lead
Free
0
3.
· 40
4. 350
·
5. IC
·
· ·
HDR-SR11/SR11E/SR12/SR12E_L2
--7--
1. SERVICE NOTE ENGLISH JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function 1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
function starts working, and displays on the Viewfinder or the LCD Viewfinder or the LCD screen shows a 4-digit display consisting of
screen what to do. This function consists of two display; self- an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
diagnosis display and service mode display. display indicates the "repaired by:", "block" in which the problem
Details of the self-diagnosis functions are provided in the Instruction occurred, and "detailed code" of the problem.
manual.
Viewfinder or LCD screen
C:31:11
Blinks at 3.2Hz
C 31 11
Repaired by: Block Detailed Code
C : Corrected by customer Indicates the appropriate Refer to "1-2-3. Self-diagnosis Code Table".
H : Corrected by dealer step to be taken.
E : Corrected by service E.g.
engineer 31 ....Reload the tape.
32 ....Turn on power again.
HDR-SR11/SR11E/SR12/SR12E_L2
1-1
ENGLISH JAPANESE
1-2-3. Self-diagnosis Code Table
Self-diagnosis Code
Repaired by:
Block Detailed Symptom/State Correction
Function Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
"Memory Stick Duo" is unformatted. Format the "Memory Stick Duo".
C 1 3 0 1
"Memory Stick Duo" is broken. Insert a new "Memory Stick Duo".
Remove the power source. Reconnect it again and operate your
C 1 3 0 2 Disc access error
camcorder again
Retry turn the power on by the power switch. If it does not
Difficult to adjust focus recover, check the focus MR sensor of lens block (pin w;, wa of
C 3 2 6 0
(Cannot initialize focus) CN5103 on the LD-230 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-230 board).
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
E 3 1 0 0 Drive fault Inspect or replacement of the hard disk drive.
Inspect the lens block zoom MR sensor (pin qh, qj of CN5103
Zoom operations fault on the LD-230 board) when zooming is performed when the
E 6 1 1 0 (Cannot initialize zoom lens.) zoom lever is operated, and the zoom motor drive circuit
(IC5201 on the LD-230 board) when zooming is not performed.
The abnormalities in initialization of
the focus lens and the abnormalities in
E 6 1 1 1 Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
E 6 2 0 0 work well. (With PITCH angular Inspect PITCH angular velocity sensors (SE9001 on the FR-278
velocity sensor output stopped.) board) peripheral circuits.
Handshake correction function does not
E 6 2 0 1 work well. (With YAW angular velocity Inspect YAW angular velocity sensors (SE9002 on the FR-278
sensor output stopped.) board) peripheral circuits.
Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
E 6 2 0 2 Abnormality of IC for steadyshot.
Occurred].
IC for steadyshot and micro controller
E 6 2 0 3 Inspect the steadyshot circuit (IC5501 on the LD-230 board).
communication abnormality among.
Replacement of lens block. If an error occurs again, replace the
E 6 2 1 0 Shift lens initializing failure.
LD-230 board. (Note 2)
Shift lens overheating (Pitch) Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
E 6 2 1 1
Occurred].
Shift lens overheating (Yaw) Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
E 6 2 1 2
Occurred].
Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor)
E 6 2 2 0 Abnormality of thermistor.
Occurred].
E 9 1 0 1 Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit.
Fault of writing or erasing the
E 9 4 0 0 Inspect the flash memory (IC2101 on the VC-516 board).
flash memory
Note 1 : Refer to Service Manual, ADJ ("1-3. DESTINATION DATA WRITE").
Note 2 : When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-2
ENGLISH JAPANESE
1-3. METHOD OF COPING WITH SHIFT LENS ERROR
about 330 msec
Note: The length of low section will vary a little depending on the
conditions.
Fig. 2
Change in output voltage of R5549 on the LD-230 board
LD-230 BOARD (SIDE A) VC-516 BOARD (SIDE A)
R5549
IC1301
IC5501
R5526
R5534
R5525
R5538
R5549: No Mount
(Short Land)
C5513
31
4
Fig. 1
Measurement points on the LD-230 board and the VC-516 board
1-3-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order Procedure
1 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501 on the LD-230 board, turn the
2
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
3
the camera control circuit (IC1301 of VC-516 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-3
ENGLISH JAPANESE
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data Procedure
1 11 80 7430 01 Write the data. (After it starts, set it before caution is displayed.)
2 11 8E F946 F0 Write the data.
3 11 8E F948 01 Write the data. (Note 1)
4 11 8E F948 00 Write the data.
5 11 8E F946 10 Write the data.
6 11 8E F948 01 Write the data. (Note 1)
7 11 8E F948 00 Write the data.
8 11 80 7430 00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
9
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5526 in the
10
periphery of IC5501 on the LD-230 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
11
varied, proceed to the order 12.
12 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
13 on the LD-230 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14 change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-516 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F948, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-4
ENGLISH JAPANESE
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data Procedure
1 11 80 7430 01 Write the data. (After it starts, set it before caution is displayed.)
2 11 8E F947 F0 Write the data.
3 11 8E F949 01 Write the data. (Note 1)
4 11 8E F949 00 Write the data.
5 11 8E F947 10 Write the data.
6 11 8E F949 01 Write the data. (Note 1)
7 11 8E F949 00 Write the data.
8 11 80 7430 00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
9
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5534 in the
10
periphery of IC5501 on the LD-230 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
11
varied, proceed to the order 12.
12 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
13 on the LD-230 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14 change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-516 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F949, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order Procedure
1 Turn the power ON.
Confirm the connections of flexible flat cables and connectors between the lens block and LD-230 board, LD-230 board and
2
VC-516 board.
In case of no malfunction of connections, replace the lens block with new one. (Note) When the error has occurred in spite of the
3
lens replacement, replace LD-230 board with new one.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-5
ENGLISH JAPANESE
1-4. PRECAUTION ON REPLACING THE VC-516 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform "DESTINATION DATA WRITE".
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform "USB SERIAL No. INPUT".
HDR-SR11/SR11E/SR12/SR12E_L2
1-6
1. SERVICE NOTE ENGLISH JAPANESE
1-1.
8.4Vdc10
DCACAC-L200/L200B
1-2.
1-2-1. 1-2-2.
L C D LCD4
3.2Hz5
LCD
C:31:11
3.2Hz
C 31 11
C
1-2-3.
H
31
E
32
HDR-SR11/SR11E/SR12/SR12E_L2
1-7
ENGLISH JAPANESE
C 0 4 0 0
C 1 3 0 1
C 1 3 0 2
C 3 2 6 0
w; wa
E 2 0 0 0
E 3 1 0 0
E 6 1 1 0
qh
qj
E 6 1 1 1
E 6 2 0 0
E 6 2 0 1
E 6 2 0 2
E 6 2 0 3
E 6 2 1 0
E 6 2 1 1
E 9 1 0 1
E 9 4 0 0
HDR-SR11/SR11E/SR12/SR12E_L2
1-8
ENGLISH JAPANESE
LD-230 BOARD (SIDE A) VC-516 BOARD (SIDE A)
R5549
IC1301
IC5501
R5526
R5534
R5525
R5538
R5549: No Mount
(Short Land)
C5513
31
4
HDR-SR11/SR11E/SR12/SR12E_L2
1-9
ENGLISH JAPANESE
1 11 80 7430 01
2 11 8E F946 F0
3 11 8E F948 01 1
4 11 8E F948 00
5 11 8E F946 10
6 11 8E F948 01 1
7 11 8E F948 00
8 11 80 7430 00
27
9 2
10
HDR-SR11/SR11E/SR12/SR12E_L2
1-10
ENGLISH JAPANESE
1 11 80 7430 01
2 11 8E F947 F0
3 11 8E F949 01 1
4 11 8E F949 00
5 11 8E F947 10
6 11 8E F949 01 1
7 11 8E F949 00
8 11 80 7430 00
27
9 210
HDR-SR11/SR11E/SR12/SR12E_L2
1-11
ENGLISH JAPANESE
1-4. VC-516
ADJDESTINATION
DATA
WRITE
USBNo.
1IDUSB
Serial
No.
IDID
ADJUSB
SERIAL
No.
INPUT
HDR-SR11/SR11E/SR12/SR12E_L2
1-12
(ENGLISH) HDR-SR11 * Manufacturing year
(JAPANESE Model)
1-6. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR11)
The model display adopts the laser printing method.Therefore, the
cabinet (G(900)) assy for replacement differs depending on the Serial No. * Affix the label
destination. Part No. Description
As similar displays are provided, choose the suitable one for order. A-1526-522-A CABINET(G(900))(SR11J1)
Note1: After replacing the cabinet (G(900)) assy, the serial number HDR-SR11
for it will be changed to the one exclusive for service use. (Tourist Model)
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the cabinet (G(900)) assy for US, affix the
"Manufacturing year" label and the "Factory" label on the specified Serial No.
location as shown in the figure. Part No. Description
A-1526-524-A CABINET(G(900))(SR11JE3)
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
HDR-SR11
(US Model) Serial No.
Note 3: When replacing the cabinet (G(900)) assy for Korea and
Japanese, affix the "Manufacturing year" label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
* Factory * Manufacturing year * Affix the label
Part No. Description
(JAPANESE) A-1526-525-A CABINET(G(900))(SR11U2)
1-6. (G(900)) HDR-SR11
(HDR-SR11) (Canadian Model)
(G(900))
Serial No.
Part No. Description
A-1526-526-A CABINET(G(900))(SR11CA2)
1:(G(900))
HDR-SR11
(E Model)
2:US(G(900))
Serial No.
Part No. Description
A-1526-527-A CABINET(G(900))(SR11E23)
(G(900))
() HDR-SR11
(Korea Model) * Affix the label
3:KoreanJapanese(G
( 9 0 0 ) )
(G(900))
() Serial No. * Manufacturing year
Part No. Description
A-1526-528-A CABINET(G(900))(SR11KR2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-13
(ENGLISH) HDR-SR11E
(E, Hong Kong, Australian Models)
1-7. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR11E)
The model display adopts the laser printing method.Therefore, the Serial No.
cabinet (G(900)) assy for replacement differs depending on the Part No. Description
destination. A-1526-529-A CABINET(G(900))(SR11EE34)
As similar displays are provided, choose the suitable one for order.
HDR-SR11E
Note1: After replacing the cabinet (G(900)) assy, the serial number (NE Models)
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Serial No.
(JAPANESE) Part No. Description
1-7. (G(900)) A-1526-530-A CABINET(G(900))(SR11ECEL)
(HDR-SR11E)
HDR-SR11E
(Tourist Model)
(G(900))
Serial No.
Part No. Description
1:(G(900)) A-1526-560-A CABINET(G(900))(SR11EJE3)
HDR-SR11E
(AEP, UK Model)
Serial No.
Part No. Description
A-1526-561-A CABINET(G(900))(SR11ECEH)
HDR-SR11E
(Chinese Model)
Serial No.
Part No. Description
A-1526-562-A CABINET(G(900))(SR11ECN2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-14
(ENGLISH) HDR-SR12 * Manufacturing year
(Japanese Model)
1-8. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR12)
The model display adopts the laser printing method.Therefore, the
cabinet (G(900)) assy for replacement differs depending on the Serial No. * Affix the label
destination. Part No. Description
As similar displays are provided, choose the suitable one for order. A-1526-563-A CABINET(G(900))(SR12J1)
HDR-SR12
Note1: After replacing the cabinet (G(900)) assy, the serial number (Tourist Model)
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the cabinet (G(900)) assy for US, affix the
Serial No.
"Manufacturing year" label and the "Factory" label on the specified
Part No. Description
location as shown in the figure. A-1526-565-A CABINET(G(900))(SR12JE3)
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy. HDR-SR12
Serial No.
(US Model)
Note 3: When replacing the cabinet (G(900)) assy for Korea and
Japanese, affix the "Manufacturing year" label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
* Factory * Manufacturing year * Affix the label
Part No. Description
A-1526-566-A CABINET(G(900))(SR12U2)
(JAPANESE) HDR-SR12
1-8. (G(900)) (Canadian Model)
(HDR-SR12)
(G(900))
Serial No.
Part No. Description
A-1526-567-A CABINET(G(900))(SR12CA2)
1:(G(900)) HDR-SR12
(E Model)
2:US(G(900)) Serial No.
Part No. Description
A-1526-568-A CABINET(G(900))(SR12E23)
HDR-SR12
(G(900)) (Korean Model) * Affix the label
()
3:KoreanJapanese(G
( 9 0 0 ) )
Serial No. * Manufacturing year
(G(900))
Part No. Description
() A-1526-575-A CABINET(G(900))(SR12KR2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-15
(ENGLISH) HDR-SR12E
(E, Hong Kong, Australian Models)
1-9. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR12E)
The model display adopts the laser printing method.Therefore, the Serial No.
cabinet (G(900)) assy for replacement differs depending on the Part No. Description
destination. A-1526-576-A CABINET(G(900))(SR12EE34)
As similar displays are provided, choose the suitable one for order. HDR-SR12E
(NE Models)
Note1: After replacing the cabinet (G(900)) assy, the serial number
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Serial No.
(JAPANESE) Part No.
A-1526-577-A
Description
CABINET(G(900))(SR12ECEL)
1-9. (G(900))
HDR-SR12E
(HDR-SR12E) (Tourist Model)
(G(900))
Serial No.
Part No. Description
A-1526-578-A CABINET(G(900))(SR12EJE3)
1:(G(900))
HDR-SR12E
(AEP, UK Model)
Serial No.
Part No. Description
A-1526-579-A CABINET(G(900))(SR12ECEH)
HDR-SR12E