Text preview for : SONY DSC-W50 SERVICE MANUAL LEVEL 2 VER 1.3 2008.09 REV-1 (9-876-936-34).pdf part of SONY DSC-W50 SONY DSC-W50
DIGITAL STILL CAMERA.
SERVICE MANUAL VERSION 1.3 2008.09 REVISION-1
PART#(9-876-936-34)
Back to : SONY DSC-W50 SERVICE MANU | Home
DSC-W50
SERVICE MANUAL
Ver. 1.3 2008.09
Revision History How to use Acrobat Reader LEVEL
2
Internal memory ON BOARD
Revised-1
Photo: Silver
Replace the previously issued SERVICE MANUAL 9-876-936-31 with this manual.
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Japanese Model Tourist Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAM SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· Precaution on Replacing the SY-144 Board
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DIGITAL STILL CAMERA
DSC-W50_L2
9-876-936-32
Sony EMCS Co.
2008I0500-1 © 2008.9 Published by Kohda TEC
SPECIFICATIONS
Camera
[System]
Image device 7.18 mm (1/2.5 type) color CCD, Primary color filter
[LCD screen]
LCD panel 6.2 cm (2.5 type) TFT drive Total number of dots 115 200 (480×240) dots
BC-CSG battery charger
Power requirements AC 100 to 240 V, 50/60 Hz, 2W Output voltage DC 4.2 V, 0.25 A Operating temperature 0 to 40°C (32 to 104°F) Storage temperature 20 to +60°C (4 to +140°F) Dimensions Approx. 62 × 24 × 91 mm (2 1/2 × 31/32 ×3 5/8 inches) (W/H/D) Approx. 75 g (2.7 oz)
Total pixel number of camera Approx. 6 183 000 pixels Effective pixel number of camera Approx. 6 003 000 pixels Lens Carl Zeiss Vario-Tessar 3× zoom lens f = 6.3 18.9 mm (38 114 mm when converted to a 35 mm still camera) F2.8 5.2
[Power, general]
Power Rechargeable battery pack NPBG1, 3.6 V AC-LS5K AC Adaptor (not supplied), 4.2 V Power consumption (during shooting with the LCD screen on) 0.9 W Operating temperature 0 to 40°C (32 to 104°F) Storage temperature 20 to +60°C (4 to +140°F) Dimensions 88.9×57.1×22.9 mm (3 1/2 inches × 2 1/4 inches × 29/32 inches) (W/H/D, excluding protrusions) Approx. 157 g (5.5 oz) (including NP-BG1 battery pack and wrist strap, etc.) Electret condenser microphone Dynamic speaker Compatible
Mass
Exposure control Automatic exposure, Scene Selection (7 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash
Rechargeable battery pack NP-BG1
Used battery Lithium-ion battery Maximum voltage DC 4.2 V Nominal voltage DC 3.6 V Capacity 3.6 Wh (960 mAh)
File format (DCF compliant) Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media Internal Memory (32 MB) "Memory Stick Duo" Flash Recommended distance (ISO set to Auto): approx. 0.2 m to 4.2 m (7 7/8 inches to 13 feet 9 3/8 inches) (W)/approx. 0.3 m to 2.2 m (11 7/8 inches to 7 feet 2 5/8 inches) (T)
Mass
Design and specifications are subject to change without notice.
Microphone Speaker Exif Print
PRINT Image Matching III Compatible PictBridge Compatible
[Input and Output connectors]
Multi connector
DSC-W50_L2 --2--
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. FLEXIBLE Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
DSC-W50_L2
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
TABLE OF CONTENTS
Section Title Page
1.
SERVICE NOTE
1-1. Description on Self-diagnosis Display ···························· 1-1 1-2. Process After Fixing Flash Error ····································· 1-1 1-3. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-2 1-4. Precaution on Replacing the SY-144 Board ···················· 1-3
2.
DISASSEMBLY
2-1. Disassembly ····································································· 2-2 2-2. Exchange Method of Barrier Assy ·································· 2-6 2-3. Exchange Method of Zoom Motor Unit ·························· 2-9
3.
BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-2 3-3. Power Block Diagram ····················································· 3-3
4.
4-1. 4-2. 4-3. 4-4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Frame Schematic Diagram ·············································· 4-1 Schematic Diagrams ························································ 4-3 Printed Wiring Boards ··················································· 4-17 Mounted Parts Location ················································ 4-26
5.
REPAIR PARTS LIST
5-1. Exploded Views ······························································· 5-2 5-2. Electrical Parts List ························································· 5-6
DSC-W50_L2 --4--
1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display · C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) · E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code C:32:ss Countermeasure Turn the power off and on again. Format the "Memory Stick" or internal memory. Insert a new "Memory Stick". Turn the power off and on again. E:61:ss E:91:ss Checking of lens drive circuit. Checking of flash unit or replacement of flash unit. (Note) Cause Trouble with hardware. "Memory Stick" or internal memory is unformatted. "Memory Stick" is broken. Trouble with internal memory. When failed in the focus and zoom initialization. Abnormality when flash is being charged. Caution Display During Error SYSTEM ERROR FORMAT ERROR MEMORY STICK ERROR INTERNAL MEMORY ERROR --
C:13:ss
Note: After repair, be sure to perfom "1-2. PROCESS AFTER FIXING FLASH ERROR".
1-2. PROCESS AFTER FIXING FLASH ERROR
When "FLASH error" (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK Cancel
See the following procedure. Cancels the resetting.
1 Select [OK] with v on the control button, then press z. The message "Initialize all settings Ready?" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting.
· Make sure that the power is not disconnected during resetting.
DSC-W50_L2 1-1
1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-144 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-144 board or the IC202 on the SY-144 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a "Memory Stick Duo".
OK Cancel
See the following procedure. Cancels the copying.
1 Insert a "Memory Stick Duo" having 32 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be copied Ready?" appears. 3 Select [OK] with v, then press z. Copying starts.
Copying 102_COPY
· Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. · You cannot copy individual images. · The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick Duo" after copying, then execute the [Format] command in (Internal Memory Tool). · You cannot select a folder copied on a "Memory Stick Duo". · Even if you copy data, a (Print order) mark is not copied.
Method for Formatting the Internal Memory
This item does not appear when a "Memory Stick Duo" is inserted in the camera. The default settings are marked with .
Format
Formats the internal memory.
· Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK Cancel
See the following procedure. Cancels the formatting.
1 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be erased Ready?" appears. 2 Select [OK] with v, then press z. The format is complete.
DSC-W50_L2 1-2
1-4. PRECAUTION ON REPLACING THE SY-144 BOARD
VIDEO OUT Default Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting because of broadcast system (NTSC/PAL). When the data has changed because of board replacing etc., check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value. VIDEO OUT Default Data Page 4F Address 8D Data NTSC 00 PAL 01
Writing Method: 1) Select page: 00, address: 01, and set data: 01. 2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL). 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is "00". 6) Select page: 80, address: 30, and check that the data is "00". 7) Select page: 00, address: 01, and set data: 00.
Initial Language Data Check
If the SY-144 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial language as that of the set distributing in each region. Initial language: Language displayed at the next starting if the setting of Setup menu was reset. It is different from the language setting selectable with the menu. Initial Language Data Page Address Data 00 04 08 0B 0D Language English Spanish Simplified Chinese Russian Korean GP2 z GP3 z z z z GP4 z z z
4F
8C
Note: GP2 is fixed to English. GP3 is either English, Spanish, or Russian. GP4 is either English, Spanish, Simplified Chinese, or Korean. Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 8C, and set the Initial Language Data. 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is "00". 6) Select page: 80, address: 30, and check that the data is "00". 7) Select page: 00, address: 01, and set data: 00. 8) Turn off the camera. 9) Turn on the camera. Execute "Initialize" of Setup screen. 10) Check the language displayed when the camera starts.
DSC-W50_L2 1-3E
2. DISASSEMBLY
NOTE FOR REPAIR
· Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. · When remove a connector, dont' pull at wire of connector. It is possible that a wire is snapped. · When installing a connector, dont' press down at wire of connector. It is possible that a wire is snapped. · Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)
DISCHARGING OF THE ST-133 BOARD'S CHARGING CAPACITOR (C901)
The charging capacitor (C901) of the ST-133 board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a resistor of 1 k /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
1 k/1 W
Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds.
Wrap insulating tape.
R:1 k/1 W (Part code: 1-215-869-11)
DSC-W50_L2 2-1
HELP
2-1. DISASSEMBLY
2-1-1. CABINET BLOCK
EXPLODED VIEW
HARDWARE LIST
2 Cabinet (Rear) Block Assy
2-5 (Claw) 2-3 (Claw) 1-6 2-2 (#18) 2-6
1-5 (#18) 2-4 (Claw)
2-1 (#18) 1-1 (#18) 1-8 (Claw) 1-9 (Claw) 1-2 (Claw) 1-4 1-3 (Claw) 1-7 (#18)
1 Cabinet (Front) Block Assy
Refer to page 2-1 " Discharging of the ST-133 board's charging capacitor (C901) ", when discharging the capacitor.
DSC-W50_L2 2-2
2-1-2. LCD BLOCK
EXPLODED VIEW
HARDWARE LIST
3-1 (#5)
3 Cabinet (Upper) Block Assy 1 LCD Block
3-2 2-3 2-6 2-4 (#5) 1-5 (Claw) 2-2 2-1 (Boss) 2-5 (Claw)
SW -46
4
1-2 1-4 (Claw)
1-1
2 SW-464 Board
1-3 (Claw)
DSC-W50_L2 2-3
2-1-3. LENS BLOCK
EXPLODED VIEW
HARDWARE LIST
1-2 (Claw) 1-3 1-5
1-1
ST -13 4
ST -13
2-1
3
2-4 (#19)
CD -60
1-4 1-6 (Claw) 1-7 2-2
4
2-5
1 ST-133 Board
2-3
2 Lens Unit
Note 1:When you exchange barrier block assembly and ornamental ring (A), be sure to follow the procedure carried on "2-2. Exchange Method of Barrier Assembly" (2-6 page). Note 2:When you exchange zoom motor unit, be sure to follow the procedure carried on "2-3. Exchange Method of Zoom Motor Unit" (2-9 page).
DSC-W50_L2 2-4
2-1-4. BT HOLDER BLOCK
EXPLODED VIEW
HARDWARE LIST
3 DC-104 Flexible Board
3-1 (Claw) 3-5 (Claw)
DC -10 4
3-6
1 SW-144 Board
1-2 3-4 (Claw) 1-5
1-3 (Claw)
SY -14 4
3-2 (Claw)
HELP
1-4
JK -30 3
3-3
1-1 (#5)
2-2
2 JK-303 Flexible Board
2-3 (#18) 2-4 2-1 (#18)
DSC-W50_L2 2-5
2-2. EXCHANGE METHOD OF BARRIER ASSY
Service parts Part Number 1 2-673-650-01 2 2-673-652-01 3 2-673-651-01 Part Name Ring (A), Ornamental Barrier Assy Tapping screw (B1.2×4) Quantity 1 1 2
1
Tools used Torque driver Soldering iron Weight about 60g Adhesive tape (ornamental ring fixed) (2-677-885-01)
2
3
2-2-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force. Heat four circled portions with the soldering iron. Heating temperature is about 300ºC. Beware of a burn since the entire Ornamental Ring becomes hot. * As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame. Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring. * Take extreme care so as not to damage the coated surface of the group-1 frame. In case of difficult peeling, heat the ring again with the soldering iron. If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 2 in the under figure one by one sequentially. * Discard the removed Ornamental Ring A.
1 2
Tip
DSC-W50_L2 2-6
2-2-2. REMOVE OLD BARRIER ASSY
1 Remove two screws. * Discard the removed screws. 2 Remove the Barrier Assy. * Discard the removed Barrier Assy.
2 1 1
* After removing the Barrier Assy, if the "G1 Dust-Proof Ring" was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction. This is an important part to prevent the dust and light from coming in. * After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-2-3. INSTALL NEW BARRIER ASSY
1 Install new Barrier Assy. 2 Tighten two screws. * Tightening torque = 0.5 kgf
1 2 2
DSC-W50_L2 2-7
2-2-4. ADHERE THE ORNAMENTAL RING A
Apply an adhesive tape to two recesses on the top surface of the Barrier Assy. Meeting a "notch" of the Ornamental Ring A with a "projection" of the group-1 frame, push the Ornamental Ring A into the group-1 frame. * The projection of the spring for preventing static electricity must be tilted. Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens. Note: Be careful not to give a shock. * After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame. A gap, if present, causes the crackle sound NG. * The weight must push in the Ornamental Ring A only. If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Do not put the weight on a black mold part.
Adhesive tape
Adhesive tape
Not gap in full circumference.
Completion after 30 minutes.
DSC-W50_L2 2-8
2-3. EXCHANGE METHOD OF ZOOM MOTOR UNIT
Service parts Part Number 1 2-673-648-01 2 2-673-649-01 Tools used Torque driver Part Name Zoom Motor Unit BT2 P1.4×3 B3C Quantity 1 2
1
2-3-1. REMOVE OLD ZOOM MOTOR UNIT
1 Remove two screws. * Discard the removed screws. 2 Remove the Zoom Motor Unit. 3 Remove the Lens Flexible Board. * Discard the removed Zoom Motor Unit.
2
2
3
1
3 3
1
2-3-2. INSTALL NEW ZOOM MOTOR UNIT
1 Install the Lens Flexible Board in new Zoom Motor Unit. 2 Install new Zoom Motor Unit in the Lens Block. 3 Tighten two screws. * Tightening torque = 0.7 kgf
2
1
1 1
3
3
DSC-W50_L2 2-9E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
CD radiation cushion
Lens cushion (130) LCD frame (130)
DSC-W50_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM
DSC-W50_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS BLOCK IRIS (METER) 17 1 IC001 BUFFER IC002 3 16
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-144 BOARD (1/2)
IC901
CD-604 FLEXIBLE BOARD
LENS
JK-303 FLEXIBLE BOARD(1/2)
K5, G4, H4, L5, H1, H2, J1, J2, M5, J4, K4,M6,K1, K2 D1, E1 - E3, F1 - F3, G1 - G3, H1 - H3, J1 A3, A5, A7 B3 - B7 B4, D5 - D8, E6 - E8
LCD DRIVE (5/7) K2 K3 K1 K6 CS, COM RGT, PSIG, HCK1, HCK2, REF, HST, PCG, XSTBY, DWN, EN, VCK, VST CN901 R 8 G 9 B 7 CN102 R G B CS, COM RGT, PSIG, HCK1, HCK2, REF, HST, PCG, XSTBY, DWN, EN, VCK, VST 21 20 22 LCD901 2.5 INCH COLOR LCD MONITOR
CN301 CCD_OUT
H10
CA_AD00 CA_AD13
LCD_D0 - LCD_D7
6, 10 - 12, 15 - 18, 23 - 26 27, 28
A2, A9, C9
B8, D9, E9
K6, K5, J6, J5
21, 22, 31, 32
2 - 4, 6
SHUTTER MOTOR
ZOOM MOTOR
FOCUS MOTOR
IRIS MOTOR
H1A, H2A, H1B, H2B RG V1A,V1B,V2,V3A,V3B,V4 V5A,V5B,V6,V7A,V7B,V8
M
M
M
M
CCD SIGNAL PROCESS, A3 TIMING GENERATOR (1/7)
CA_FD
J5 X102 33.75MHz C1
W25 IC101 (1/2) CAMERA DSP, CPU, LENS CONTROL, MODE CONTROL (2/7)
XCS_ PANEL
B10 C10
XIC_101_RST_OUT
19
8
K4
23 - 29, 31 - 35
G7, H6, G6, G5, H5, H4, G4, F4, E4, D7, H7, D4
B1, K4, C2, D2, J4, D1, E2, F2, F1, G2, G1, H2
CCD IMAGER
IC301
A2
H5
LCD_HD, LCD_VD,LCD_CK
3 - 6, 11 - 14, 17 - 19, 23
CA_HD
J6
1, 2
1 - 3, 5, 6 8 - 10, 12 14 - 16
ZOOM SENSOR 1, 2
FOCUS RESET SENSOR
A4
CLKTGO
A10, B9 1 3 BL_H BL_L CN101 6 1
E1 F2 U22
D901 BACKLIGHT
Q301
E7
C1
XIC_101_RST_OUT
Q302
T4, R23
VSUB_CONT_PRE, VSUB_CONT_POST
IC_101_1_SO, XIC_101_1_SCK
11 7 26 27
22 30 39 38
VHLD VST VSUB VSUB_CONT
B3, C3
D5 D6 C4
C2
XCS_FE
IC_101_1_SO, XIC_101_1_SCK
BL_L BL_H
IC401 LENS DRIVE D4 (3/7) CN401 IRIS_ M_+, M_
XCAM_DR_PS
1
P21
AF4
XIC_101_RST_OUT
OVERALL (2/2) (PAGE 3-2)
AB6, AC4, AE4, AE5, AC5,AF6
D2, B1
D3, E3
20, 21
IRIS MOTOR DRIVER
P4, N4
IRIS_ (+), ()
IRIS_M_IN, IRIS_M_EN
MS_BS, MS_D0 MS_D3, MS_CLK
12 - 15
F_MOTOR_A, A(), B, B()
FOCUS_A, A, B, B
R6, U2
FOCUS MOTOR DRIVER
D5, A6, B6, C5
D6, E6, B7, C6
N5, L2, L4
FC_DIR_A, FC_DIR_B, FC_BRK_A
H26 U23
IC_101_VOUT VIDEO_AMP_ON
IC602 3 4 VIDEO AMP (6/7) 5
V_LINE_OUT
IC_101_1_SO, XIC_101_1_SCK
IC_101_1_SO, XIC_101_1_SCK IC_101_AUOUT IC_101_AUIN XCS_AUDIO
2
Z_DC_MOTOR (+), ()
ZOOM_DC_+, DC_
ZOOM MOTOR DRIVER
P5, N2, N6
B2, C4, A2
B4, B5
8 - 11
ZM_DIR_A, ZM_BRK_A, ZM_BRK_B
OVERALL (2/2) (PAGE 3-2)
K26 L26 Y26
SHUTTER_(+), () F_PI_SENS_OUT, XFC_RST_LED Z_BOX2_PI_SENS_COL, Z_BOX1_PI_SENS_COL, XZM_RST_LED, Z_BOX1, BOX2, Z_PI_SENS_OUT
SHUTTER_+,
XIC_101_RST_OUT
SHUTTER MOTOR DRIVER
16 - 19
G1, E4
R5, R25
F4, F3
MSHUT_DIR, MSHUT_EN
AC1, AD1
USB_DP, USB_DM XIC_101_RST_OUT XIC_101_RST_OUT
2, 3, 5, 6, 27. 29 24, 26
U4, E5
FC_SENS, XFC_RST_LED ZM_DC_FG_1A, ZM_DC_FG_1B, XZM_FG_LED, ZM_SENS_1ST,XZM_RST_LED LENS_TEMP
B4
B3, D4, V4, V5, W4
LENS TEMP SENSOR
30
J25
AB13, AA13, AE13, AF13, AF12, AE12, AA12, AC12, AC11, AB12, AE11, AF11, AE10, AB11, AC10, AB10 D21, D22, D20, B22, A22, A23, B23, E20, E21, B24, A24, A25, B25, C25, C26, B26, E10, A10, D10, E11, B10, A11, B11, E12, D11, D12, F12, B12, A12, E13, D13, D14, F13, B15, F14, E14, D17, D18, D16, B18, A19, B19, E16, D19, E19, E17, B20, A20, B21, A21
CPU_D00 CPU_D15
C9, C10, D9, D10, D11, D12,E10, E11, J10, J11, J12, K10,K11, K12, L11, L12 C5 - C8, D5 - D8, E4, E5, E8, E9, F3 - F9, G2 - G5, G9, G10, H2, H3, H4, H8, H9, H10, J3 - J9, K3, K4, K8, K9, L4, L5, L9, L10, M4, M5, M9, M10
CPU_D00- CPU_ D15
DSP_AQ0 DSP_AQ11, DSP_DQ0 DSP_DQ31, DSP_DQM0 DSP_DQM3, DSP_QBA0, DSP_QBA1 CPU_A20, CPU_A21 IC201 XIC_101_RST_OUT BURST FLASH E2 - E6, D5, (4/7) F2 - F7, G1, G3, G5, G7 B5 A1, A2, A6, A7, A8, B1, B2, B3, B6, B7, B8, C1, C2, C6, C7, C8, D1, D2, D4, D8, E8 E7 B4
ST-133 BOARD
T001 XE_H C901 CHARGING + CAPACITOR D002 5 4 1 3 2 15 XE_L Q001 FLASH DRIVE IC001 FLASH CONTROL, CHARGE CONTROL 10 9 CN001 9 12 ST_UNREG
ST-134 FLEXIBLE BOARD
M3, E3
IC202 128M SDRAM, 32M SUPER AND (4/7) M7 N7
CPU_D00- CPU_ D15 CN704 STRB_CHG XSTRB_FULL 14 17 R22 V23 AF21, AF20, AE20, AB18, AB19, AC19,AB16, AE19, AF19, AF18, AE18, AA15, AC18, AC17, AB15, AE17, AF17, AE16, AB14, AC16, AC15 AE6 4 6 10 11 STRB_ON STRB_CHG_CONT 15 16 R4 AB22 AF9 A17 A18 14 XAF_LED 19 CPU_A01- CPU_A21 XCPU_CS0 IC_101_27M_CLKO DSP_QCLKE DSP_QCLK
FLASH UNIT
TRIGGER TRIGGER_GND
1, 2
7
DSP_QCLKE DSP_QCLK XAF_LED
05
D003 SELF-TIMER/ AF ILLUMINATOR
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
SP901 SPEAKER MIC901
SP+, SPMIC_SIG
22, 23
SP+, SPMIC_SIG
3
OVERALL (2/2) (PAGE 3-2)
21
DSC-W50_L2 3-1
3-2. OVERALL BLOCK DIAGRAM (2/2)
SY-144 BOARD (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN703 MS_BS, MS_D0 MS_D3, MS_CLK MS_BS, MS_D0 MS_D3, MS_CLK
2 - 5, 7, 8
MEMORY STICK DUO
XMS_IN
F3, E3
6
MIC_SIG IC603 AUDIO AMP (6/7) B6
A5, A2
IC101_1_SO, XIC_101_1_SCK
SP+, SP-
IC_101_AUOUT IC_101_AUIN
3
XAF_LED
E5 E6 E4 D1
OVERALL (1/2) (PAGE 3-1)
OVERALL (1/2) (PAGE 3-1)
2
XCS_AUDIO
JK-303 FLEXIBLE BOARD (2/2)
AU_LINE_OUT V_LINE_OUT AU_LINE_OUT V_LINE_OUT CN702 11 13
6, 8
A_OUT_L V_OUT
16 20
10, 12
USB_DP, USB_DM
USB_DP, USB_DM
USB_DP, USB_DM
XIC_101_RST_OUT
USB_VBUS
4
USB_VBUS 6 XAV_JACK_IN 26
SW-464 BOARD
RL-065 FLEXIBLE BOARD
S003 (SHUTTER) CN705 17 18 CN002 7 XSTRB_LED 9 XAE_LOCK_SW XSHUTTER_SW XSTRB_LED N21 P23 IC101 (2/2)
U25
XAV_JACK_IN
XAV_JACK_IN
14
V1
EVER_SRAM D001 IC102 (2/2) (2/7) IC_101_TXD4 IC_101_RXD4 3 4 Q102 BATTERY CHARGE DETECT BATT_SIG D003 VL_3V 1 BT001 LITHIUM BATTERY CN001 MULTI CONNECTOR
V25
XACV_IN
BATT/XEXT
31
BATT_XEXT
19
E22
D002 (FLASH CHARGING/RECORD) XAE_LOCK_LED D002 (POWER) XAE_LOCK_LED XPWR_LED
FRONT CONTROL AA26 (2/7) AB25 6 8 1 F22 D23 A6 D702 (ACCESS) E4 KEY_AD0, AD1
K23, L23
XAF_LED IC102 (1/2) (2/7) EXTAL 2 IC103 3 BATTERY AUTHENTICATE (2/7) 6-8 1 6 1 X101 12MHz MS_VCC D_3.2V A_3.2V CAM_2.9V D_1.8V M_5V D_1.2V PANEL_8.5V CAM_12V CAM_7.5V
A4
B10 C9 B8 H1
XMS_IN USB_VBUS
D001 (AE/AF LOCK/SELF-TIMER)
D004 ST_UNREG DC/DC CONVERTER (7/7)
23, 25
S001-S009
2, 3, 4
ACV_UNREG
32 - 39
FUNCTION KEY
KEY_AD0, AD1, PLAY_SW
4, 5, 6
IC001
ACV_UNREG
A9 A8
S006 T
(ZOOM)
S005 W 16 KEY_AD2 H25
X001 32.768kHz
Q001, Q002
DC-104 FLEXIBLE BOARD
AA5, AB5, Y5
C6, C5, B6
CHARGE_V BATT_SIG
11 - 14
CONTOROL SW BLOCK (SW110T/SW120TB)
CN001
S002 POWER
3
XPOWER_ON
K25 T25 W23
BATT_SENS MS_PWR_ON XCS_DD IC_101_0_SI, IC_101_0_SO, XIC_101_0_SCK XDD_RST_OUT XPWR_OFF BL_H BL_L
D4 D3 A6
CN701 CHARGE_V BATT_SIG
+
S
10
14, 15
MODE DIAL
L22, L25
11, 12
1, 5
MODE_DIAL0, 1
MODE_DIAL0,1
R26 Y4 AA23
A7 B7 E9 F9 XPLAY_SW XPOWER_ON
2-5
BH001 BATTERY TERMINAL
OVERALL (1/2) (PAGE 3-1)
XPLAY_SW
ACV_UNREG BATT/XEXT
ACV_UNREG BATT/XEXT J001 DC IN
1
1
D7 C7
05
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
DSC-W50_L2 3-2
3-3. POWER BLOCK DIAGRAM
JK-303 FLEXIBLE BOARD (1/2)
23, 25 32-39
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
ST-134 FLEXIBLE BOARD
1-5 1-3
SY-144 BOARD
CN702 F001 CN704 ST_UNREG UNREG F002 13
ST-133 BOARD
T001 CN001
ACV_UNREG
ACV_UNREG
ST_UNREG ST_5V
L001
D002
FLASH UNIT
8 IC001 D003 SELF-TIMER/ AF ILLUMINATOR FLASH CONTROL, CHARGE CONTROL
CN001 MULTI CONNECTOR
D_3.2V
18
D_3.2V
13
BT001 LITHIUM BATTERY BATT/XEXT
VL_3V
1
VL_3V
VL_3V IC001 Q001, Q002 DC/DC CONVERTER (7/7) J1 K1 J6 K6 A1 B1 C2 D10 UNREG1-1 UNREG1-2 UNREG2-1 UNREG2-2 PWR1-1 PWR1-2 PWR1-3 PWR2 L004 LX3 E10 D005 VO3 E9 VL3 F9 VO1-1 F1 VO1-2 F2 VFB1 H2 L003 BL_H BL_L D_3.2V IC601 2.9V REG (6/7) 4 VIN VOUT 3 A_2.9V AU_3.0V M_5V LDO2IN B3
ACV_UNREG BATT/XEXT CHARGE_V XACV_IN
JK-303 FLEXIBLE BOARD (2/2)
LCD901 CN901 PANEL_8.5V 22 F003 VDD CN102 7 2.5 INCH COLOR LCD MONITOR D901 BACKLIGHT 6 1
19
31
BATT/XEXT
D003
D001
CN101 BL_H BL_L 1 3 BL_H BL_L
SW-464 BOARD
D001 AE/AF LOCK/ SELF-TIMER CN002 1
RL-065 FLEXIBLE BOARD
2 D002 (POWER) D_3.2V S002 POWER 3
CN705
D_3.2V
B8 RTCBAT D004 H1 LDO1 XPOWER_ON XPOWER_ON C7 XPWRON1
IC603 AUDIO AMP (6/7) M_5V L901 L904
IC901 LCD DRIVE (5/7)
D002 FLASH CHARGING/ RECORD
LDO2 A3 LDO3IN B2 LDO3 A2 L002 LX2 C10 VFB2 D8 CAM_2.9V
A_3.2V D_1.8V D_3.2V
L903
CN401 D_1.2V
LENS BLOCK Z_BOX1_PI_SENS_VCC 1 Z_BOX2_PI_SENS_VCC 4 Z_PI_SENS_VCC 28 ZOOM RESET SENSOR
MEMORY STICK DUO
9
G2 MS_PWR D3 MS_PWR_ON
MS_PWR_IN G1 Q003
L006
Q004, Q005 SWITCHING M_5V IC401 LENS DRIVE (3/7)
D_3.2V
CN703
MS_VCC
MS_VCC
L001
25
F_PI_SENS_VCC
EVER_SRAM
BG4 G9 TG4 F10 PSG4 G8 VFB4 F7 VREF6 G6 VFB6 H7 BATT_SENS D4 UNREGMON GT6 H6
C6, C5, B6
DC CONTROL
PANEL_8.5V D_1.2V D_1.8V A_3.2V AU_3.0V D_3.2V
FOCUS RESET SENSOR
V1 XACV_IN T25 V25 MS_PWR_ON
D_3.2V IC201 BURST FLASH (4/7) CAM_2.9V CAM_7.5V
L304 L305 FB309 L303 FB307
IC301 CCD SIGNAL PROCESS (1/7)
DC-104 FLEXIBLE BOARD
CN701
K25 IC101 CHARGE_V Q102 BATTERY CHARGE 10 DETECT IC102 (2/7) 4 3 AA26
6-9
+
BH001 BATTERY TERMINAL S
CHARGE_V
BATT_SIG ACV_GND
AB25
CAMERA DSP, CPU, LENS CONTROL, MODE CONTROL, FRONT CONTROL (2/7)
AA5, AB5, Y5
IC_101_0_SI, IC_101_0_SO, XIC_101_0_SCK
11 - 14
SCLK SI SO
L007
Q006 SWITCHING
Q007 B- SWITCH
CAM_7.5V
W23 R26 Y4 AA23
XCS_DD XDD_RST_OUT XPWR_OFF
A6 CE A7 XRESET B7 XPWROFF
PWR56OUT1 J7 PWR56OUT2 K7 LX5-1 J9 LX5-2 J10 LX5-3 K9 LX5-4 K10 VFB5 H9
Q008 B+ SWITCH D008 IC002 8.5V REG (7/7) PANEL_8.5V L201 IC202 128M SDRAM, 32M SUPER AND (4/7) L301 FB301 CAM_12V CAM_12V
FB308
CD-604 FLEXIBLE BOARD
CN301 12 36 CAM_12V IC002 CAM_7.5V CCD IMAGER
BATT/XEXT J001 DC IN ACV_UNREG LF001
1
2-5
BATT/XEXT ACV_UNREG
P25 L102
7.5VON
D_1.2V
D_1.2V IC103 BATTERY AUTHENTICATE (2/7) IC602 VIDEO AMP (6/7) IC001 BUFFER
D_3.2V
A13, B13, D25, D26
SDRAM_VCC A_3.2V AU_3.0V L101 D_3.2V A_3.2V AU_3.0V D_3.2V D601
G26
VIDEO_VCC
L601
FB107
D_3.2V
05
DSC-W50_L2 3-3E
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
BH001 BATTERY TERMINAL
1
3
23
1
DC-104 FLEXIBLE BOARD
3 5
J001 DC IN
MIC901 MICROPHONE BLOCK
1
4
ST-134 FLEXIBLE BOARD
14 1 1 14
SP901 SPEAKER
LEVEL3 SY-144 BOARD (SIDE A)
LEVEL3 SY-144 BOARD (SIDE B)
1 19 23 1 19
C901 CHARGING CAPACITOR
CN701
14 1
22
CN704
18
CN705
1 2
2 39 39
CD-604 FLEXIBLE BOARD
38
RL-065 FLEXIBLE BOARD
ST-133 BOARD (SIDE B)
1 2
1 1 2
10 2 1 1
CN901
30
31
CN301
CN001
13 14
IC201 (Not supplied) CN703 MEMORY STICK CONNECTOR
29
28
1
2
CN702
2
1
CN401
FLASH UNIT
1 12
12
38
39
11
LENS BLOCK SW-464 BOARD (SIDE B)
CN002
12 1
SW-464 BOARD (SIDE A) CONTROL SW BLOCK SW110T/ SW120TB
JK-303 FLEXIBLE BOARD
1
BT001 LITHIUM BATTERY CN001
6 1
29
1
CN101
6 39 26 2 1 25 28 1 27 24
CN102
1
D901 BACKLIGHT
LCD901 CN001 MULTI CONNECTOR 2.5 INCH COLOR LCD MONITOR
DSC-W50_L2 4-1
+
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-604 FLEXIBLE BOARD (CCD IMAGER) ST-133 BOARD (FLASH DRIVE) ST-134 FLEXIBLE BOARD SW-464 BOARD (CONTROL SWITCH) RL-065 FLEXIBLE BOARD (CONTROL SWITCH) CONTROL SW BLOCK (SW110T/SW120TB) JK-303 FLEXIBLE BOARD (MULTI/LCD CONNECTOR) DC-104 FLEXIBLE BOARD (BATTERY IN, DC IN)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-W50_L2
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor External dimensions (mm) Case size · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B Line · J : IN/OUT direction of (+,) B LINE. · C: adjustment for repair. · A: not use circuit (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.) Precautions for Replacement of Imager · If the imager has been replaced, carry out all the adjustments for the camera section. · As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. 1. Connection
Pattern box
Color bar chart Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = 30 cm (PTB-450) L = 12 cm (PTB-1450) Pattern box L Front of the lens Camera
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
Cyan Green
White Magenta
A B
A=B
Fig. a (Video output terminal output waveform) Electronic beam scanning frame CRT picture frame
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
DSC-W50_L2 4-3
Red Blue
B A
1
2
3
4
5
6
7
8
9
10
11
12
13
A
CD-604 FLEXIBLE BOARD
CCD IMAGER
XX MARK:NO MOUNT
B
CL003
CL006
12 11 10 9
VHLD V6 V5B V5A
CL002
8
V4
7
VST
6
V3B
CL004
5
V3A
C
Note: CD-604 flexible complete board, IC001 and IC002 are not supplied, but they are included in CCD block assy. Note: Voltages of IC001 and IC002 can not be measured, because this is mounted by the side of the lens.
CL001 13 14 15 16
N.C. V7A V7B V8 CCD-OUT VH RG N.C.
N.C. V2
4 3 2 1 CL005 32 31 30 29
IC002
CCD IMAGER IC002 ICX624EQP-13
V1B V1A H2A H1A VL N.C.
D
LND039 LND038 LND037 LND036 LND035 LND034 LND033 VSUB 39 VSUB_CONT 38 GND 37 CAM_-7.5V 36 V1A 35 V1B 34 V2 33
17 R001 33 18 19 20 3 2
GND
1
IN
WGND
RSS3
GND
CSUB
IC001
BUFFER IC001 CXA3691EN-T9
OUT
SUB
H1B
H2B
IDRV
VCC
ISF
E
21 22 23 24 25 26 27 28 4 5 6 R008 0 C008 0.01u 16V R004 220k R009 XX C004 0.1u 16V
LND032 LND031 LND030 LND029 LND028 LND027 LND026
V3B 32 V3A 31 VST 30 V8 29 V4 28 V7B 27 V5A 26 V7A 25 V5B 24 V6 23 VHLD 22 GND 21 GND 20 GND 19 CCD_GND 18 NC 17 CCD_OUT 16 GND 15 GND 14 GND 13 CAM_12V 12 GND 11 GND 10 GND RG GND H1B NC H1A H2B H2A GND 9 8 7 6 5 4 3 2 1 R002 0 C001 0.01u 16V
F
SY-144 (1/7)
CN301 PAGE 4-6 of LEVEL3
LND025 LND024 LND023 LND022 LND021 LND020 LND019 LND018 LND017 LND016 LND015 LND014 LND013 LND012 LND011 LND010
R007 560 C002 XX C003 0.1u 16V
C005 XX
C007 0.1u
N.C.
C006 0.1u
G
H
LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002
I
05
LND001
DSC-W50_L2 4-5
CD-604
Schematic diagrams of the SY-144 board are not shown. Pages from 4-6 to 4-12 are not shown.
DSC-W50_L2
· Refer to page 4-3 for mark 0.
1
2
3
4
5
6
7
8
9
10
11
12
13
A
ST-133 BOARD
FLASH DRIVE
B
ST-134 FLEXIBLE BOARD
Note: MIC901 is not supplied, but this is included in ST-134 flexible complete board.
LND048 SP+ SP901 SPEAKER
XX MARK:NO MOUNT NO MARK:REC/PB MODE
T001 4 1 C002 22u C003 22u 2 3 LND006 DISCHARGE D003 DOR5352 SELF-TIMER/ AF ILLUMINATOR 17 LND046 N.C N.C HGND 16 15 VBATT 4 MIC901 5 6 CN001 14P 14 2 13 12 11 4 10 0 9 G_IGBT I_PEAK 8 N.C 7 6 5 4 3 2 1 F_ON 5 3 VCC SW DISCHARGE LND005 4.2 14 13 N.C 250 LND004 XE_L C901 97u 315V CHARGING CAPACITOR R004 1M LND001 TRIGGER LND002 TRIGGER_GND SPLND047 FLASH UNIT 5
L001 2.2uH
D002 MA2YF8000LS0
LND003 XE_H
C
LND023 LND022 LND021 LND020 LND019 SP+ 23 SP- 22 MIC_SIG 21 REG_GND 20 XAF_LED 19 D_3.2V 18 XSTRB_FULL 17 I_PEAK 16 STRB_ON 15 STRB_CHARGE 14 ST_5V 13 REG_GND 12 REG_GND 11 REG_GND 10 REG_GND 9 REG_GND 8 REG_GND 7 REG_GND 6 ST_UNREG 5 ST_UNREG 4 ST_UNREG 3 ST_UNREG 2 ST_UNREG 1
MIC_SIG REG_GND LND045
3 2 1
SW
PGND
14 XAF_LED 13 D_3.2V 12 XSTRB_FULL 11 I_PEAK 10 STRB_ON 9 STRB_CHARGE 8 ST_5V 7 REG_GND 6 REG_GND 5 REG_GND 4 REG_GND 3 ST_UNREG 2 ST_UNREG 1 ST_UNREG
LND044 LND043 LND042 LND041 LND040 LND039 LND038 LND037 LND036 LND035 LND034 LND033 LND032 LND031
XAF_LED D_3.2V XSTRB_FULL I_PEAK STRB_ON STRB_CHARGE ST_5V REG_GND REG_GND REG_GND REG_GND ST_UNREG ST_UNREG ST_UNREG
D
LND018 LND017 LND016 LND015 LND014
IC001
FLASH CONTROL, CHARGE CONTROL IC001 TPS65552RGTR
PGND CHG XFULL
11
12
4.2 1
C007 0.047u 250V
4
3
2
1 Q001 TIG022TS-S-TL-E FLASH DRIVE
8 7 0.1 R003 33 3.2 0 R005 1M
6
5
SY-144 (2/7)
CN704 PAGE 4-7 of LEVEL3
LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003
E
5 0.1
6
7 0
8
C001 0.001u
C004 1u
N.C
9 C005 0.1u
F
05
LND002 LND001
DSC-W50_L2 4-13
10
ST-133, ST-134
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
A
RL-065 FLEXIBLE BOARD
CONTROL SWITCH
XX MARK:NO MOUNT Note: RL-065 flexible complete board and S003 (shutter) are not supplied, but they are included in cabinet (upper) block assy.
LND001 LND002 LND003 LND004 LND005 LND006 XPWR_LED 1 D_3.2V 2 XPOWER_ON 3 KEY_AD0 4 KEY_AD1 5 PLAY_SW 6 REG_GND 7
XAE_LOCK_LED 8
B
SW-464 BOARD
CONTROL SWITCH
XX MARK:NO MOUNT
CN002 1 D_3.2V 2 KEY_AD0 3 KEY_AD1 4 PLAY_SW 5 REG_GND 6 XAE_LOCK_LED 7 XSTRB_LED 8 N.C 9 N.C 10 N.C 11 MODE_DIAL0 12 MODE_DIAL1 LND021 LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 LND030 LND031 LND032 12P 1 2 3 4 5 6 7 8 9 10 11 12 (SELF-TIMER) (MACRO) (FLASH) ADJUSTING EXPOSURE D002 SML-310YTT86 (FLASH CHARGING/RECORD) 4 3 S001 4 3 S004 4 3 4 3 4 3 S009 2 1 2 1 2 1 2 1 2 1 D001 SML-510MWT86S (AE/AF LOCK/SELF-TIMER) R001 2200 R002 2200 R003 2200 R006 3300 D_3.2V KEY_AD0 KEY_AD1 PLAY_SW REG_GND XAE_LOCK_LED XSTRB_LED N.C N.C N.C MODE_DIAL0 MODE_DIAL1
D002 CL-196SYG-CD-T (POWER)
C
LND007
SY-144 (2/7)
CN705 PAGE 4-7 of LEVEL3
LND008 LND009 LND010 LND011 LND012 LND013 LND014
XSTRB_LED 9 REG_GND 10 N.C 11 N.C 12 N.C 13 MODE_DIAL0 14 MODE_DIAL1 15 KEY_AD2 16
XAE_LOCK_SW 17 XSHUTTER_SW 18
S006
S008
D
LND015 LND016 LND017 LND018 LND019
1
2
R004 2200
R005 2200
REG_GND 19
3 S002 POWER R002 XX 2 3 D003 MAZW068H0LS0
4 3 2 3 2 2 D005 XX C001 XX (PLAYBACK) 1 2 4 S002 SCREEN DISPLAY SWITCH 1 3 2 1 2 1
LND001 STATIC_GND
1 D003 XX
1 D004 XX
4
3
4 S005
3
4
3
E
S003
S007 MENU
LND020
STATIC_GND
1 R001 2200
IMAGE SIZE/ DELETE
S005 W (ZOOM)
S006 T
F
S003 (SHUTTER) 4 3
CONTROL SW BLOCK (SW110T/SW120TB)
CONTROL SW BLOCK (SW110T/SW120TB) is replaced as block, so that PRINTED WIRING BOARD is omitted.
R112 2200 R111 3600 R110 8200
2
3 1 1 D001 MAZW068H0LS0 2
SW110T: SILVER model SW120TB: BLACK model
G
10 Landscape CN001 6P 1 MODE_DIAL0 NC REG_GND NC MODE_DIAL1 NC LND101 LND102 LND103 LND104 LND105 LND106 MODE_DIAL0 1
9 Beach
8 Snow
7 Twilight portrait 6 Twilight
R109 22000
H
2 3 4 5 6
NC 2 REG_GND 3 NC 4 MODE_DIAL1 5 1 NC 6 Soft snap MOVIE AUTO P_AUTO 2 3 4 R116 22000 5 MANUAL
I
05
R113 2200
R114 3600
R115 8200
DSC-W50_L2 4-14
SW-464, RL-065, SW110T/SW120TB
· Refer to page 4-3 for mark 0.
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
A
JK-303 FLEXIBLE BOARD
MULTI/LCD CONNECTOR
XX MARK:NO MOUNT Note: CN001 (multi connector) is not supplied, but this is included in JK-303 flexible complete board.
BT001 LITHIUM BATTERY CN001 28P (MULTI CONNECTOR) TO AV/USB MULTICABLE OR CRADLE 27
2 1
A
DC-104 FLEXIBLE BOARD
BATTERY IN, DC IN
XX MARK:NO MOUNT
CHARGE_V LND001 CHARGE_V 14 CHARGE_V 13 CHARGE_V 12 CAHRGE_V 11 BATT_SIG 10 ACV_GND 9 ACV_GND 8 ACV_GND 7 ACV_GND 6 ACV_UNREG 5 ACV_UNREG 4 ACV_UNREG 3 ACV_UNREG 2 BATT/XEXT 1 3 1 2 LF001 0uH 4 2 3 1 4 J001 DC IN 5 3 1 2
B
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009
VL_3V N.C N.C USB_VBUS USB_GND USB_DP N.C USB_DM USB_GND
1 2 3 4 5 6 7 8 9 FB001 1 2 LF001 0uH 3 4 XSTATION_IN(N.C.) SET_ID_IN(N.C.) USB_VBUS USB_GND USB_DP USB_DM USB_GND A_OUT_L A_GND V_OUT V_GND XCHG_ON(N.C.) XAV_JACK_IN
ACV_GND ACV_GND ACV_GND XPOWER_ON(N.C.) KEY_A/DB(N.C.) N.C. N.C. KEY_A/DA(N.C.) CHARGE_V(N.C.) BATT_XEXT CHARGE_V(N.C.) ACV_UNREG ACV_UNREG 28
B
SY-144 (7/7)
CN701 PAGE 4-12 of LEVEL3
LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009
S
BH001 BATTERY TERMINAL
4
6
8
26 24 22 20 18 16 14 12 10
25 23 21 19 17 15 13 11
9
7
5
3
C
LND010 LND011 LND012 LND013 LND014 LND015 LND016
A_GND 10
AU_LINE_OUT
C
LND010 LND011 LND012 LND013 LND014
11 FB002
V_GND 12
V_LINE_OUT XAV_JACK_IN
13 14
N.C 15 ACV_GND 16 ACV_GND 17 ACV_GND 18 ACV_GND 19 ACV_GND 20 ACV_GND 21 ACV_GND 22 N.C 23 N.C 24 N.C 25 N.C 26 N.C 27 N.C 28 N.C 29 N.C 30 BATT/XEXT 31 ACV_UNREG 32 ACV_UNREG 33 ACV_UNREG 34 ACV_UNREG 35 ACV_UNREG 36 ACV_UNREG 37 ACV_UNREG 38 ACV_UNREG 39
STATIC_GND
STATIC_GND
LND018
D
SY-144 (6/7)
CN702 PAGE 4-11 of LEVEL3
LND017 LND018 LND019 LND020 LND021 LND022 LND023 LND024 LND025
D
05
E
LND026 LND027 LND028 LND029 LND030 LND031 LND032
F
LND033 LND034 LND035 LND036 LND037 LND038 LND039
LND129
N.C. 29 COM 28 CS 27 VST 26 VCK 25 EN 24 DWN 23 VDD 22 VSS 21 N.C. 20 VSSG 19 XSTBY 18 PCG 17 HST 16 REF 15
TEST1(N.C.)
CN102 24P 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 COM CS VST VCK EN DWN VDD VSS N.C. VSSG XSTBY PCG HST REF TEST1(N.C.) N.C. HCK2 HCK1 PSIG G R B RGT TEST2(N.C.) LCD901 2.5INCH COLOR LCD MONITOR
G
LND128 LND127 LND126 LND125 LND124 LND123 LND122 LND121
H
SY-144 (5/7)
CN901 PAGE 4-10 of LEVEL3
LND120 LND119 LND118 LND117 LND116 LND115 LND114 LND113 LND112 LND111 LND110 LND109 LND108 LND107 LND106 LND105
14
I
N.C. 13 HCK2 12 HCK1 11 PSIG 10 G R B RGT
TEST2(N.C.)
9 8 7 6 5 4 3 2 1
J
LND104 LND103 LND102 LND101
N.C. BL_L N.C. BL_H
CN101 6P 6 5 4 3 2 BL_H NC NC NC NC BL_L D901 BACKLIGHT
K
05
1
DSC-W50_L2 4-15
JK-303, DC-104
4-3. PRINTED WIRING BOARDS
Link
CD-604 FLEXIBLE BOARD ST-133 BOARD ST-134 FLEXIBLE BOARD SW-464 BOARD RL-065 FLEXIBLE BOARD JK-303 FLEXIBLE BOARD DC-104 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
DSC-W50_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
: Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers' patterns are not indicated) · Through hole is omitted. · There are a few cases that the part printed on diagram isn't mounted in this model. · C: panel designation · · · Chip parts. Transistor
C 6 5 4 4 5 6 5 4 4 5
Diode
3 3 3 1 23
B
E
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 2
2 4
1 2 3 3
1 2
1 6 54
4 6 5 4 4 5 6
5 4 3 3 4 5 4
1
1 3
2 2
2
1 1 2 3 3 2 1
4
1
DSC-W50_L2 4-17
CD-604 (2 layers)
: Uses unleaded solder.
CD-604 FLEXIBLE BOARD
39
LND039 LND038 LND037 LND036 LND035 LND034 LND033 LND032 LND031 LND030 LND029 LND028 LND027 LND026 LND025 LND024 LND023 LND022 LND021 LND020 LND019 LND018 LND017 LND016 LND015 LND014 LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
CD 604 CD-604 >PI< PI 1 867 705 1-867-705R007 C005
CL002 CL001
A
C001
R002
R001
R004
CL006
CL003
CL004 CL005
C008 R009
1
R008
C002
12 13
IC001
6
4
1
3
5 4
C004
C003
C006
20
29 21
28
1-867-705- 11
05
Note: CD-604 flexible complete board, IC001 and IC002 are not supplied, but they are included in CCD block assy.
DSC-W50_L2 4-19
C007
IC002
1 32
CD-604
Printed wiring boards of the SY-144 board are not shown. Page 4-20 is not shown.
DSC-W50_L2
ST-133 (4 layers), ST-134 (2 layers)
: Uses unleaded solder.
ST-133 BOARD (SIDE B)
FLASH UNIT
XE_L XE_H TRIGGER_GND TRIGGER
ST-133 BOARD (SIDE A)
5 1
LND004
ST-133
B
C004
2
5 17 8 9 12 13
T001
IC001
4 1 16
C007
14
4
3
ST-133
C001
CN001
13
1
C005
1-867-701- 11
LND002
LND001
C002
C003
Q001
L001
R003
1
8
3
4
LND005
LND006
05
1-867-701- 11
05
ST-134 FLEXIBLE BOARD
LND044 LND043 LND042 LND041 LND040 LND039 LND038 LND037 LND036 LND035 LND034 LND033 LND032 LND031
C901 CHARGING CAPACITOR
+
LND047
LND048
14
1
SP-
SP+
SP901 SPEAKER
MIC901
R005
D003
D003 SELF-TIMER/ AF ILLUMINATOR
4
5
R004
1
6
LND046 LND045
ST-134
>PI< >PI<
05
1
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 LND023
23
1-867-792- 11
DSC-W50_L2 4-21
ST-133, ST-134
D002
>EP GW<
LND003
2
SW-464 (2 layers)
: Uses unleaded solder.
SW-464 BOARD (SIDE A)
D001
D001 AE/AF LOCK/ SELF-TIMER
D005
LND001
SW-464 BOARD (SIDE B)
2
4
S003 (PLAYBACK)
K
A
S003
D002
K
A
D002 FLASH CHARGING/ RECORD
1
3
C001
D003 D004
3
1
2
A
CN002 12 1
A
1 2 3
S002 SCREEN DISPLAY SWITCH
B
R004
3
1
B
CN001 6 1
S002
4
2
S007 MENU
2 4
R003
S007
S006
3
1
C
(FLASH)
2 4
R006
R002
C
S006
1
3
S009
S008 ADJUSTING EXPOSURE
3
4 3
1
1 2
S009
S004 (MACRO)
S008
3
S004
2
1
4
2
R001
3 1
S001
D
R005
4
4
S001
(SELF-TIMER)
2 4
D
S005 IMAGE SIZE/ DELETE
2
S005
1-867-709- 11
1 3
1-867-709- 11
05
1
2
3
05
3
2
1
DSC-W50_L2 4-22
SW-464
RL-065 (2 layers), JK-303 (2 layers), DC-104 (2 layers)
: Uses unleaded solder.
RL-065 FLEXIBLE BOARD
1
LND001 LND003 LND005 LND007 LND009 LND011 LND013 LND015 LND017
DC-104 FLEXIBLE BOARD
+ S -
19
LND019
LND002
LND004
LND006
LND008
LND010
LND012
LND014
LND016
LND018
BH001
Note: RL-065 flexible complete board and S003 (shutter) are not supplied, but this is included in cabinet (upper) block assy.
1
3
DC-104 >PI<
LND018
3
LF001
3
LND020
D002 (POWER)
1
4
J001
S005 W
RL-065 S003 >PI<
S006 T
1
2
5
J001 DC IN
4
D001
(SHUTTER)
2 2 1
A
2 3 1
-392-
1
4
D002
1-867-704- 11
S002
S003
S00 6 5 S00
1 2 3
4
3
3
R002
D003
05
R001
S002 POWER
1-868-392- 11
05
14
JK-303 FLEXIBLE BOARD
LND021 LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 LND030 LND031 LND032
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014
1
1
LND101 LND103 LND105 LND107 LND109 LND111 LND113 LND115 LND117 LND119 LND121 LND123 LND125 LND127
LND102 LND104 LND106 LND108 LND110 LND112 LND114 LND116 LND118 LND120 LND122 LND124 LND126 LND128
1
12
303-KJ -707-768-1
BT001 BATTERY, LITHIUM SECONDARY
29
LND129
1
LND001 LND003 LND005 LND007 LND009 LND011 LND013 LND015 LND017 LND019 LND021 LND023 LND025 LND027 LND029 LND031 LND033 LND035 LND037
LND002 LND004 LND006 LND008 LND010 LND012 LND014 LND016 LND018 LND020 LND022 LND024 LND026 LND028 LND030 LND032 LND034 LND038 LND036
BT001
39
FB002
LND039
2 4
1 3
B
2 1 24 CN102
6
CN101 27 1
FB001
LF001
26
28
LND040
25 CN001
1-867-707- 11
(MULTI CONNECTOR)
05
Note: CN001 (multi connector) is not supplied, but this is included in JK-303 flexible complete board.
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
DSC-W50_L2 4-23
RL-065, JK-303, DC-104
1
Mounted parts location of the SY-144 board are not shown. Page 4-25 is not shown.
DSC-W50_L2
4-3. PRINTED WIRING BOARDS
4-4. MOUNTED PARTS LOCATION
SW-464 BOARD
CN001 B-3 * CN002 A-2 D001 D002 R001 R002 R003 R004 R005 R006 S001 S002 S003 S004 S005 S006 S007 S008 S009 A-1 A-1 D-3 C-3 C-2 B-2 D-2 C-2 D-3 B-2 A-1 D-3 D-2 C-3 C-2 D-2 D-3
no mark : side A * mark : side B
DSC-W50_L2 4-26E
SW-464
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
A
B
C
CABINET BLOCK
LCD BLOCK
LENS BLOCK
D
BT HOLDER BLOCK
Link
CD-604 FLEXIBLE BOARD DC-104 FLEXIBLE BOARD JK-303 FLEXIBLE BOARD
ELECTRICAL PARTS LIST
C D D
ACCESSORIES
C B
RL-065 FLEXIBLE BOARD ST-133 BOARD
B C
ST-134 FLEXIBLE BOARD SW-464 BOARD
DSC-W50_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... · Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
· Language that can be selected about SY-144 board
Traditional Chinese Arabic Dutch Russian Swedish Korean Norwegian Danish Finnish Polish Hungarian Czech
z z z z z z z z z z z z z
Japanese English French German Spanish Italian Portugal Simplified Chinese
GP1 GP2
GP3
GP4
J US CND AUS Vietnam AEP UK E AR BR TW JE HK CH KR
z
z z
z z
z
z z z z z z
z
z
z
z
z z
DSC-W50_L2 5-1
Persian Thai
Area
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. CABINET BLOCK
DISASSEMBLY
HARDWARE LIST
7
6 5 2 3
#18 #18
#18
#18
LCD Block (See page 5-3.)
4 1
#18
Ref. No. 1 1 2 3 4
Part No. A-1174-923-A A-1174-930-A 2-666-506-01 2-666-418-01 2-666-507-01
Description CABINET (FRONT) BLOCK ASSY (SILVER) CABINET (FRONT) BLOCK ASSY (BLACK) CABINET, BT SIDE BRACKET, STRAP CABINET, LE SIDE
Ref. No. 5 5 6 7 #18
Part No. A-1166-462-A A-1166-464-A 2-666-491-01 2-666-505-01
Description CABINET (REAR) BLOCK ASSY (SILVER) CABINET (REAR) BLOCK ASSY (BLACK) SHEET (130), WINDOW ADHESIVE WINDOW (130), LCD
2-635-591-21 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
DSC-W50_L2 5-2
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-2. LCD BLOCK
HARDWARE LIST
#5
53
(including RL-065 flexible board)
LCD901 D901 #5
52
SW -46
4
54 51
Lens Block (See page 5-4.)
Ref. No. 51 52 52 53
Part No. A-1167-019-A 1-479-584-11 1-479-584-21 A-1166-159-A
Description SW-464 BOARD, COMPLETE CONTROL SW BLOCK (SW110T) (SILVER) CONTROL SW BLOCK (SW120TB) (BLACK) CABINET (UPPER) BLOCK ASSY (including RL-065 flexible board)
Ref. No. * 54
Part No.
Description
2-666-428-01 SHEET (130), LCD REINFORCEMENT
D901 1-479-554-11 BLOCK, LIGHT GUIDE PLATE (2.5) LCD901 8-753-257-48 ACX336AKA-3 #5 3-080-204-01 SCREW, TAPPING, P2 (Black)
DSC-W50_L2
5-3
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-3. LENS BLOCK
ns: not supplied
HARDWARE LIST
BT holder Block (See page 5-5.)
104
(including MIC901)
111
ST -13 4
SP901
105
(including IC001, IC002 (CCD imager) and CD-604 flexible board) (Note 1, 2)
3
ST -13
#19
CD -60 4
103 102 110
(Note 4) C901
108
(Note 3)
107
(Note 3)
101
ns
109
(Note 3)
106
(Note 3, 4) M901 (Note 4) ns
ns
ns
Note 1:
CCD block assembly is including CD-604 flexible completed board. Be sure to read "Precuations for Replacement of Imager" on page 4-3.
Note 3:
Be sure to read "Exchange method of barrier assembly" on page 2-6. Be sure to read "Exchange method of zoom motor unit" on page 2-9.
Note 2:
Note 4:
·
Refer to page 5-1 for mark 0. Part No. A-1166-208-A 1-479-663-21 2-666-420-01 A-1166-044-A Description Ref. No. 108 109 110 111 0* C901 M901 SP901 #19 Part No. Description
Ref. No. 0 101 0 102 * 103 104 105
ST-133 BOARD, COMPLETE FLASH UNIT HOLDER, STROBOSCOPE ST-134 FLEXIBLE BOARD, COMPLETE (including MIC901) A-1166-155-A CCD BLOCK ASSY (including IC001, IC002 (CCD IMAGER) and CD-604 flexible board) (Note 1, 2) 1-788-363-11 OPTICAL UNIT (ED13A) (Note 3, 4) 2-673-650-01 RING (A), ORNAMENTAL (Note 3)
2-673-652-01 BARRIER ASSY (Note 3) 2-673-651-01 TAPPING SCREW (B1.2X4) (Note 3) 2-673-649-01 BT2 P1.4X3 B3C (Note 4) 3-941-343-01 1-112-819-11 2-673-648-01 1-826-281-11 TAPE (A) ELECT 97uF ZOOM MOTOR UNIT (Note 4) LOUDSPEAKER (1.0CM)
315V
106 107
3-086-156-21 SCREW B1.2 (Red)
DSC-W50_L2
5-4
Ver. 1.3 2008.09
The changed portions from Ver. 1.2 are shown in blue.
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-4. BT HOLDER BLOCK
ns: not supplied
158 157
DC -10
161
4
159 156 163 162 160 155
ns
SY -14
4
153
JK -30 3
#5 BT001
151
#18
154
152
#18
! : BT001on the mountLITHIUM SECONDARY) (BATTERY, Board position.
(See page 4-23.)
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
* Refer to the table of page 5-1 about language of SY-144 board. · Refer to page 5-1 for mark 0.
Ref. No. 151 151 151 * 152 153 154 * 155 156 156 157
Part No. A-1176-190-A A-1176-191-A A-1176-192-A 2-666-424-01 2-666-423-01 A-1166-050-A 2-666-425-01 X-2108-259-1 X-2108-260-1 2-666-426-01
Description SY-144 BOARD, COMPLETE (SERVICE) (GP4) SY-144 BOARD, COMPLETE (SERVICE) (GP2) SY-144 BOARD, COMPLETE (SERVICE) (GP3) PLATE, MULTI FIXED SCREW (130), TRIPOD JK-303 FLEXIBLE BOARD, COMPLETE PLATE (130), BT GROUND HOLDER ASSY (130) (J), BT (SILVER) HOLDER ASSY (130) (J), BT (BLACK) LID (130), DC
Ref. No. 158 * 159 * 160 * 161 162 163 0 BT001 #5 #18
Part No. A-1166-045-A 2-666-427-01 2-666-429-01 2-666-422-01 2-666-392-01 2-666-391-02 1-528-999-61 3-080-204-01 2-635-591-21
Description DC-104 FLEXIBLE BOARD, COMPLETE CUSHION (130), LENS CUSHION, CD RADIATION FRAME (130), LCD SPRING, BT LOCK CLAW, BT LOCK BATTERY, LITHIUM SECONDARY SCREW, TAPPING, P2 (Black) SCREW (M1.4), NEW TRUSTAR P2 (Silver)
DSC-W50_L2
5-5
CD-604
Ref. No. Part No.
DC-104
Description
JK-303
RL-065
ST-133
Ref. No. Part No. Description < FERRITE BEAD > FB001 FB002 1-469-580-11 INDUCTOR, FERRITE BEAD (1005) 1-469-580-11 INDUCTOR, FERRITE BEAD (1005) < LINE FILTER >
5-2. ELECTRICAL PARTS LIST
A-1166-155-A CCD BLOCK ASSY (Note) (Not supplied) CD-604 FLEXIBLE BOARD, COMPLETE ******************************* (CD-604 flexible complete board, IC001 and IC002 are not supplied, but they are included in CCD block assy.) < CAPACITOR > LF001 C001 C003 C004 C006 C007 C008 1-164-943-81 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 0.1uF 0.1uF 0.1uF 0.01uF 10% 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V 16V 1-456-583-11 COMMON MODE CHOKE COIL
1-164-943-81 CERAMIC CHIP < IC >
A-1166-159-A CABINET (UPPER) BLOCK ASSY (Not supplied) RL-065 FLEXIBLE BOARD, COMPLETE ******************************* (RL-065 flexible complete board and S003 (shutter) are not supplied, but they are included in cabinet (upper) block assy.) < DIODE > D001 D002 D003 6-500-776-01 DIODE MAZW068H0LS0 6-500-594-01 DIODE CL-196SYG-CD-T (POWER) 6-500-776-01 DIODE MAZW068H0LS0 < RESISTOR >
IC001 IC002
(Not supplied) IC CXA3691EN-T9 (Not supplied) ICX624EQP-13 (Note) < RESISTOR >
R001 R002 R004 R007 R008
1-218-935-11 1-218-990-81 1-218-981-11 1-218-950-11 1-218-990-81
RES-CHIP SHORT CHIP RES-CHIP RES-CHIP SHORT CHIP
33 0 220K 560 0
5% 5% 5%
1/16W R001 1/16W 1/16W S002 S003 S005 S006 1-786-157-11 (Not supplied) 1-786-180-31 1-786-179-31 1-216-825-11 METAL CHIP < SWITCH > SWITCH, TACTILE (POWER) TACTILE SWITCH (SHUTTER) SWITCH, PUSH (1KEY) (W (ZOOM)) SWITCH, PUSH (1KEY) (T (ZOOM)) 2.2K 5% 1/10W
A-1166-045-A DC-104 FLEXIBLE BOARD, COMPLETE ******************************* < BATTERY TERMINAL > 0 0 BH001 1-780-061-21 BATTERY TERMINAL BOARD < JACK > J001 1-817-331-11 DC JACK 5P < LINE FILTER > * LF001 1-457-217-21 COMMON MODE CHOKE COIL 0
A-1166-208-A ST-133 BOARD, COMPLETE ******************** 1-479-663-21 FLASH UNIT < CAPACITOR > C001 C002 C003 C004 C005 1-162-964-11 1-100-611-91 1-100-611-91 1-165-908-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 22uF 22uF 1uF 0.1uF 0.047uF 97uF 10% 20% 20% 10% 10% 10% 50V 6.3V 6.3V 10V 10V 250V 315V
A-1166-050-A JK-303 FLEXIBLE BOARD, COMPLETE ******************************* (CN001 (multi connector) is not supplied, but this is included in JK-303 flexible complete board.) < BATTERY >
0 C007 0* C901
1-100-758-11 CERAMIC CHIP 1-112-819-11 ELECT < CONNECTOR >
CN001 0 BT001 1-528-999-61 BATTERY, LITHIUM SECONDARY
1-815-762-51 CONNECTOR, FFC/FPC 14P < DIODE >
< CONNECTOR > CN001 * CN101 * CN102 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P 1-816-650-51 FFC/FPC CONNECTOR (LIF) 24P 0* D002 * D003 6-501-433-01 DIODE MA2YF8000LS0 6-501-364-01 DIODE DOR5352 (SELF-TIMER/AF ILLUMINATOR) < IC > IC001 Note: Be sure to read "Precautions for Replacement of Imager" on page 4-3 when changing the imager. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. * L001 6-707-555-01 IC TPS65552RGTR < COIL > 1-400-820-11 INDUCTOR 2.2uH
· Refer to page 5-1 for mark 0.
DSC-W50_L2 5-6
ST-133
Ref. No. Part No. Description < TRANSISTOR > 0* Q001 6-551-447-01 TRANSISTOR < RESISTOR > R003 0 R004 R005 1-216-803-11 METAL CHIP 1-216-121-11 RES-CHIP 1-216-857-11 METAL CHIP 33 1M 1M 5% 5% 5% 1/10W 1/10W 1/10W TIG022TS-S-TL-E Ref. No. Part No. Description
ST-134
SW-464
Electrical parts list of the SY-144 board is not shown. Pages 5-8 to 5-11 are not shown.
< TRANSFORMER > 0 T001 1-443-648-21 DC-DC CONVERTER TRANSFORMER
A-1166-044-A ST-134 FLEXIBLE BOARD, COMPLETE ****************************** (MIC901 is not supplied, but this is included in ST-134 flexible complete board.) < MICROPHONE > MIC901 (Not supplied) MICROPHONE BLOCK < SPEAKER > SP901 1-826-281-11 LOUDSPEAKER (1.0CM)
A-1167-019-A SW-464 BOARD, COMPLETE ************ < CONNECTOR > * CN001 * CN002 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P < DIODE > D001 D002 8-719-075-29 DIODE SML-510MWT86S (AE/AF LOCK/SELF-TIMER) 8-719-077-34 DIODE SML-310YTT86 (FLASH CHARGING/RECORD) < RESISTOR > R001 R002 R003 R004 R005 R006 1-218-957-11 1-218-957-11 1-218-957-11 1-218-957-11 1-218-957-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 2.2K 2.2K 2.2K 2.2K 2.2K 3.3K 5% 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
1-218-959-11 RES-CHIP < SWITCH >
S001 S002 S003 S004 S005 S006 S007 S008 S009
1-786-885-41 1-786-885-41 1-786-885-41 1-786-885-41 1-786-885-41
SWITCH, TACTILE (V (SELF-TIMER)) SWITCH, TACTILE (SCREEN DISPLAY SWITCH) SWITCH, TACTILE (N (PLAYBACK)) SWITCH, TACTILE (B (MACRO)) SWITCH, TACTILE (IMAGE SIZE/DELETE)
1-786-885-41 SWITCH, TACTILE (v (FLASH)) 1-786-885-41 SWITCH, TACTILE (MENU) 1-786-885-41 SWITCH, TACTILE (b (ADJUSTING EXPOSURE)) 1-786-885-41 SWITCH, TACTILE (z)
· Refer to page 5-1 for mark 0.
DSC-W50_L2 5-7
Checking supplied accessories. Other accessories
2-667-828-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP) 2-667-828-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN) (AEP) 2-667-828-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) (AEP) 2-667-834-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAK) (AEP) 2-667-834-21 INSTRUCTION (READ THIS FIRST) (SWEDISH, FINNISH) (AEP) 2-667-834-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN, DANISH) (AEP) 2-673-200-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP, UK, E, HK, AUS, JE) 2-673-200-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-673-200-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-673-200-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-673-200-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-673-365-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US, CND) 2-673-365-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND, AEP) 2-667-836-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (CND, AEP) 2-667-836-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) (AEP) 2-667-836-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN) (AEP) 2-667-836-91 INSTRUCTION (USER'S GUIDE) (POLISH, CZECH) (AEP) 2-667-837-11 INSTRUCTION (USER'S GUIDE) (HUNGARIAN, SLOVAK) (AEP) 2-667-837-21 INSTRUCTION (USER'S GUIDE) (SWEDISH, FINNISH) (AEP) 2-673-204-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (US, CND, AEP, UK, E, HK, AUS, JE) 2-673-204-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-673-204-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-673-204-71 INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E) 2-673-204-81 INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE)
Battery Charger BC-CSG 0 1-479-583-21 (US, CND)
Battery Charger BC-CSG 0 1-479-583-31 (EXCEPT US, CND)
USB/AV Cable for Multiuse Terminal 1-829-866-11
Power Cord 0 1-555-074-71 (AUS) 0 1-782-476-41 (CH) 0 1-783-374-22 (HK) 0 1-783-952-51 (AR) 0 1-792-549-31 (JE) 0 1-823-947-51 (KR) 0 1-824-910-31 (AEP, E) 0 1-827-269-22 (UK)
Rechargeable Battery Pack NP-BG1 (not supplied)
Battery Case (not supplied)
Wrist Strap 2-050-981-01
CD-ROM (Cyber-shot Application Software) 2-666-673-01
Conversion (2P) Adaptor 0 1-569-007-12 (JE)
Conversion (2P) Adaptor 0 1-569-008-12 (E)
· Refer to the page 5-1 for mark 0.
DSC-W50_L2 5-12E
DSC-W50
LEVEL
2
SERVICE MANUAL
Ver 1.1 2006.08
SUPPLEMENT-1
File this supplement with the service manual.
(DI06-023)
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Japanese Model Tourist Model
· Addition of Japanese Model · Change of SY-144 Board's Suffix No. · Change of Repair Parts
DSC-W50_L2
9-876-936-82
Sony EMCS Co.
2006H0500-1 © 2006.8 Published by Kohda TEC
1. SERVICE NOTE
1-4. PRECAUTION ON REPLACING THE SY-144 BOARD
Initial Language Data Check : Points added portion.
&
Initial Language Data Page Address Data 00 01 04 08 0B 0D Language English Japanese Spanish Simplified Chinese Russian Korean GP1 z z z z z z GP2 z GP3 z GP4 z
*
4F
8C
Note: GP1 is fixed to Japanese. GP2 is fixed to English. GP3 is either English, Spanish, or Russian. GP4 is either English, Spanish, Simplified Chinese, or Korean.
*
3. BLOCK DIAGRAMS
& : Points added portion.
3-1. OVERALL BLOCK DIAGRAM (1/2)
(Service manual page 3-1) SUFFIX: -11
ST-134 FLEXIBLE BOARD
D10, E11, B10, A1 D11, D12, F12, B1 D13, D14, F13, B1 D17, D18, D16, B1 E16, D19, E19, E1 B21, A2
SUFFIX: -12
ST-134 FLEXIBLE BOARD
D10, E11, B10, A1 D11, D12, F12, B1 D13, D14, F13, B1 D17, D18, D16, B1 E16, D19, E19, E1 B21, A2
CN001 9 12
CN704 STRB_CHG XSTRB_FULL 14 17 R22 V23 AF21, AF20, AE20, AB18, AE19, AF19, AF18, AE18, AB15, AE17, AF17, AE16,
CN001 9 12
CN704 STRB_CHG XSTRB_FULL 14 17 Q701 FLASH CONTROL R22 V23 R4 AB22 AF21, AF20, AE20, AB18, AE19, AF19, AF18, AE18, AB15, AE17, AF17, AE16,
10 11
STRB_ON STRB_CHG_CONT
15 16
R4 AB22
10 11
STRB_ON STRB_CHG_CONT
15 16
14
XAF_LED
19
14
XAF_LED
19
5. REPAIR PARTS LIST
& : Points added portion.
5-1. EXPLODED VIEWS
Page
Ref. No. Part No.
Former
Description Ref. No. Part No. 151
New
Description A-1206-275-A SY-144 BOARD, COMPLETE (SERVICE) (GP1)
5-5
)
DSC-W50_L2 --2--
& : Points added portion. : Points changed portion. ! : Points deleted portion.
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory, but is not prepared as a service part.
*
Other accessories
2-667-828-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP) 2-667-828-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN) (AEP) 2-667-828-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) (AEP) 2-667-834-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAK) (AEP) 2-667-834-21 INSTRUCTION (READ THIS FIRST) (SWEDISH, FINNISH) (AEP) 2-667-834-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN, DANISH) (AEP) 2-673-237-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP, UK, E, HK, AUS, JE) 2-673-237-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-673-237-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-673-237-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-673-237-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-673-368-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US, CND) 2-673-368-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND) 2-673-365-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND, AEP) 2-886-440-01 INSTRUCTION (READ THIS FIR