Text preview for : SONY STR-DG800 SERVICE MANUAL VER 1.1 20006.05 (9-887-172-02).pdf part of SONY STR-DG800 SONY STR-DG800 MULTI CHANNEL AV RECEIVER. SERVICE MANUAL VERSION 1.1 20006.05 PART#(9-887-172-02)



Back to : SONY STR-DG800 SERVICE MA | Home

STR-DG800
SERVICE MANUAL
Ver. 1.1 2006. 05

US Model Canadian Model E Model

Photo: Silver type

Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", "Surround EX", and the double-D symbol are trademarks of Dolby Laboratories. "DTS", "DTS-ES", "Neo:6", and "DTS 96/24" are trademarks of Digital Theater Systems, Inc. This receiver incorporates High-Definition Multimedia Interface (HDMITM) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. XM is a registered trademark of XM Satellite Radio Inc.

SPECIFICATIONS
AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code US only) With 8 ohm loads, both channels driven, from 20 ­ 20,000 Hz; rated 100 watts per channel minimum RMS power, with no more than 0.09 % total harmonic distortion from 250 milliwatts to rated output. Amplifier section
Power Output Models of area code US, CND Stereo Power Output 1), Reference Power Output 1) 2) 8 ohms 20 Hz ­ 20 kHz, THD 0.09 % 100 W + 100 W, 110 W/ch 8 ohms 1 kHz, THD 0.7 % 110 W + 110 W, 120 W/ch 8 ohms 1 kHz, THD 10 % 125 W + 125 W, 150 W/ch Models of area code E2, TW Stereo Power Output 1), Reference Power Output 1) 2) 8 ohms 20 Hz ­ 20 kHz, THD 0.09 % 85 W + 85 W, 110 W/ch 8 ohms 1 kHz, THD 0.7 % 100 W + 100 W, 120 W/ch 8 ohms 1 kHz, THD 10 % 125 W + 125 W, 150 W/ch Models of area code MY, SP Stereo Power Output 1), Reference Power Output 1) 2) 8 ohms 20 Hz ­ 20 kHz, THD 0.09 % 75 W + 75 W, 90 W/ch 8 ohms 1 kHz, THD 0.7 % 85 W + 85 W, 100 W/ch 8 ohms 1 kHz, THD 10 % 105 W + 105 W, 125 W/ch 1) Measured under the following conditions: Area code Power requirements US, CND 120 V AC, 60 Hz E2 240 V AC, 50 Hz MY, SP 230 V AC, 50 Hz TW 110 V AC, 60 Hz 2) Reference power output for front, center, surround and surround back. Depending on the sound field settings and the source, there may be no sound output. Frequency response Analog

10 Hz ­ 70 kHz, +0.5/­2 dB (with sound field and equalizer bypassed)

­ Continued on next page ­

MULTI CHANNEL AV RECEIVER

9-887-172-02
2006E04-1 © 2006. 05

Sony Corporation
Home Audio Division Published by Sony Techno Create Corporation

1

STR-DG800
Ver. 1.1

Inputs Analog

General
Sensitivity: 500 mV/ 50 kohms S/N 3) : 96 dB (A, 500 mV 4) ) Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) S/N: 100 dB (A, 20 kHz LPF) Voltage: 500 mV/10 kohms Voltage: 2 V/1 kohm ±10 dB, 1 dB step Power requirements Area code US, CND E2 MY, SP TW Power consumption Area code US CND E2 MY, SP TW Power requirements 120 V AC, 60 Hz 120/220/240 V AC, 50/60 Hz 230 ­ 240 V AC, 50/60 Hz 110 V AC, 60 Hz

Digital (Coaxial)

Digital (Optical) Output (Analog) AUDIO OUT SUB WOOFER Equalizer Gain levels

Power consumption 260 W 360 VA 280 W 230 W 550 W

3) INPUT SHORT (with sound field and equalizer bypassed). 4) Weighted network, input level.

FM tuner section
Tuning range Intermediate frequency Useable sensitivity S/N Mono/Stereo: Harmonic distortion at 1 kHz Mono/Stereo: Separation Frequency response 87.5 ­ 108.0 MHz 10.7 MHz 11.2 dBf, 1 µV/75 ohms 76 dB/70 dB 0.3%/0.5% 45 dB at 1 kHz 30 Hz ­ 15 kHz, +0.5/­2 dB

Power consumption (during standby mode) 0.2 W AC outlets Area code AC outlets US, CND 2 switched, 120 W/1A MAX E2 , MY, SP 1 switched, 100 W/0.4A MAX Dimensions (w/h/d) (Approx.) 430 × 157.5 × 351.5 mm (16 7/8 × 6 2/8 × 13 7/8 inches) including projecting parts and controls Mass (Approx.) 11.0 kg (24 lb 5 oz) Supplied accessories FM wire antenna (1) AM loop antenna (1) Remote commander RM-AAP008 (1) (US, CND) Remote commander RM-AAP009 (1) (E2, MY, SP, TW) R6 (size-AA) batteries (2) Optimizer microphone ECM-AC2 (1) Design and specifications are subject to change without notice. · Abbreviation CND : Canadian model E2 : 120 V AC area in E model MY : Malaysia model SP : Singapore model TW : Taiwan model

AM tuner section
Tuning range Models of area code US, CND With 10-kHz tuning scale: 530 ­ 1,710 kHz 5) With 9-kHz tuning scale: 531 ­ 1,710 kHz 5) Models of area code E2 With 10-kHz tuning scale: 530 ­ 1,610 kHz 5) With 9-kHz tuning scale: 531 ­ 1,602 kHz 5) Models of area code MY, SP, TW With 9-kHz tuning scale: 531 ­ 1,602 kHz 5) Intermediate frequency 450 kHz Usable sensitivity 50 dB/m (at 1,000 kHz or 999 kHz) 5) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down CATEGORY MODE (US, CND) or DIMMER (E2, MY, SP, TW), press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.

Video section
Inputs/Outputs Video: S-video: COMPONENT VIDEO: 1 Vp-p, 75 ohms Y: 1 Vp-p, 75 ohms C: 0.286 Vp-p, 75 ohms Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0.7 Vp-p/ 75 ohms PR/CR/R-Y: 0.7 Vp-p/ 75 ohms 80 MHz HD Pass Through

2

STR-DG800
Ver. 1.1

SAFETY CHECK-OUT (US MODEL) After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set

MODEL IDENTIFICATION
-- BACK PANEL --

Part No.

MODEL US CND MY, SP TW E2

PART No. 2-666-932-0s 2-666-932-1s 2-666-932-2s 2-666-932-3s 2-666-932-5s

· Abbreviation CND : Canadian model E2 : 120 V AC area in E model MY : Malaysia model SP : Singapore model TW : Taiwan model

0.15 µF

1.5 k

AC voltmeter (0.75 V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

3

STR-DG800

TABLE OF CONTENTS 1. GENERAL
Description and location of parts (US, CND model) .............. 5

2. DISASSEMBLY
2-1. 2-2. 2-3. 2-4. 2-5. 2-6. Case ................................................................................... 10 Front Panel Section ........................................................... 11 Back Panel Section ............................................................ 11 DIGITAL Board ................................................................ 12 MAIN Board Section ........................................................ 12 STANDBY Board ............................................................. 13

3. TEST MODE ..................................................................... 14 4. DIAGRAMS
4-1. Block Diagram ­ Tuner/Audio Section ­ .......................... 15 4-2. Block Diagram ­ Digital Section ­ ................................... 16 4-3. Block Diagram ­ Video Section ­ ..................................... 17 4-4. Block Diagram ­ XM Section (US, CND model) ­ .......... 18 4-5. Block Diagram ­ Key/Display/HDMI Section ­ .............. 19 4-6. Block Diagram ­ Power Section ­ .................................... 20 4-7. Circuit Boards Location .................................................... 21 4-8. Printed Wiring Board ­ Main Section ­ ............................ 22 4-9. Schematic Diagram ­ Main Section (1/4) ­ ...................... 23 4-10. Schematic Diagram ­ Main Section (2/4) ­ ...................... 24 4-11. Schematic Diagram ­ Main Section (3/4) ­ ...................... 25 4-12. Schematic Diagram ­ Main Section (4/4) ­ ...................... 26 4-13. Printed Wiring Board ­ Digital Section (1/2) ­ ................ 27 4-14. Printed Wiring Board ­ Digital Section (2/2) ­ ................ 28 4-15. Schematic Diagram ­ Digital Section (1/5) ­ ................... 29 4-16. Schematic Diagram ­ Digital Section (2/5) ­ ................... 30 4-17. Schematic Diagram ­ Digital Section (3/5) ­ ................... 31 4-18. Schematic Diagram ­ Digital Section (4/5) ­ ................... 32 4-19. Schematic Diagram ­ Digital Section (5/5) ­ ................... 33 4-20. Printed Wiring Boards ­ Front A/B Speaker Section ­ .......................................... 34 4-21. Schematic Diagram ­ Front A/B Speaker Section ­ .......................................... 35 4-22. Printed Wiring Board ­ Video Section (1/2) ­ .................. 36 4-23. Printed Wiring Board ­ Video Section (2/2) ­ .................. 37 4-24. Schematic Diagram ­ Video Section (1/2) ­ ..................... 38 4-25. Schematic Diagram ­ Video Section (2/2) ­ ..................... 39 4-26. Printed Wiring Board ­ Video (Audio) Section ­ ............. 40 4-27. Schematic Diagram ­ Video (Audio) Section ­ ................ 40 4-28. Printed Wiring Board ­ S-video Section ­ ........................ 41 4-29. Schematic Diagram ­ S-video Section ­ ........................... 41 4-30. Printed Wiring Board ­ HDMI Section ­ .......................... 42 4-31. Schematic Diagram ­ HDMI Section ­ ............................ 43 4-32. Printed Wiring Board ­ XM Section (US, CND model) ­ ................................... 44 4-33. Schematic Diagram ­ XM Section (US, CND model) ­ ................................... 45 4-34. Printed Wiring Boards ­ Panel Section ­ .......................... 46 4-35. Schematic Diagram ­ Panel Section ­ .............................. 47 4-36. Printed Wiring Board ­ Display Section ­ ........................ 48 4-37. Schematic Diagram ­ Display Section ­ ........................... 49 4-38. Printed Wiring Boards ­ Power Section ­ ......................... 50 4-39. Schematic Diagram ­ Power Section ­ ............................. 51

5. EXPLODED VIEWS
5-1. 5-2. 5-3. 5-4. Case Section ...................................................................... 66 Front Panel Section ........................................................... 67 Back Panel Section ............................................................ 68 Chassis Section ................................................................. 69

6. ELECTRICAL PARTS LIST ........................................ 70

4

STR-DG800 SECTION 1 GENERAL
US, CND model:
Name Function
The current status of the selected component or a list of selectable items appears here (page 7). Lights up when multi channel audio is decoded (page 43).

Ver. 1.1
This section is extracted from instruction manual.
Name Function

Getting Started

G Display

S CATEGORY +/­ Press to select a category (page 75). T CATEGORY MODE U MEMORY/ ENTER Press to select the category mode (page 74). Press to store a station or enter the selection when selecting the settings (page 33). To connect a camcorder or video game (page 29, 40). Connects to a headphone (page 94).

Getting Started

Description and location of parts
Front panel
1 2 34 56 7 8 9 q; qa qs

H MULTI CHANNEL DECODING lamp

I Remote sensor Receives signals from remote commander. J DISPLAY Press to select information displayed on the display (page 82). Press to select the input mode when the same components are connected to both digital and analog jacks (page 78). Turn to adjust the volume level of all speakers at the same time (page 39, 40, 42, 43). Press to listen to high quality analog sound (page 66). Press to select the audio directly from the components connected to the MULTI CH IN jacks (page 40). Turn to select the input source to playback (page 40, 42, 43, 66, 68, 71, 78, 82, 83). Press to select sound fields for movie or music (page 63). Press to select A.F.D. mode (page 61). Press to select 2CH STEREO mode (page 66, 67).

V VIDEO 3 IN/ PORTABLE AV IN jacks W PHONES jack

?/1
MASTER VOLUME
MULTI CHANNEL DECODING

K INPUT MODE

TONE MODE

TUNING MODE

DISPLAY

INPUT MODE

ñ TONE + SPEAKERS (OFF/A/B/A+B)

ñ TUNING +

INPUT SELECTOR

X AUTO CAL MIC Connects to the supplied jack ECM-AC2 optimizer microphone for the Auto Calibration function (page 35).

AUTO CAL MIC
MEMORY/ ENTER CATEGORY MODE

­ CATEGORY +

2CH

A.F.D.

MOVIE

MUSIC

MULTI CH IN

DIRECT

L MASTER VOLUME

VIDEO 3 IN/PORTABLE AV IN PHONES

VIDEO

L AUDIO R

DIGITAL(OPT)

M DIRECT

wf wd

ws

wa w;

ql

qk qj

qh

qg

qf

qd

N MULTI CH IN

PUSH

O INPUT SELECTOR

To remove the cover Press PUSH. When you remove the cover, keep it out of reach from children.

Name
A ?/1

Function
Press to turn the receiver on or off (page 33, 42, 43, 67, 98). Press to select OFF, A, B, A+B of the front speakers (page 35). Press to select Equalizer mode (page 47). Turn to adjust the EQUALIZER menu parameters (page 47, 52). Press to select the tuning mode (page 71, 98). Turn to scan a station (page 68, 70).

P MOVIE, MUSIC Q A.F.D. R 2CH

B SPEAKERS (OFF/A/B/A+B) C TONE MODE D TONE +/­

E TUNING MODE F TUNING +/­

continued

5US

6US

About the indicators on the display
Getting Started

Name
L COAX

Function
Lights up when INPUT MODE is set to "AUTO 2CH" and the source signal is a digital signal being input through the COAXIAL jack, or when INPUT MODE is set to "COAX FIXED" (page 78). Lights up when a memory function, such as Preset Memory (page 70), etc., is activated. Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations, see page 69. Lights up when using the receiver to tune in radio stations (page 67), etc. Lights up when the digital assign function is used for selected input. Lights up when DTS Neo:6 Cinema/Music decoder is activated (page 62).

Name
U Playback channel indicators

Function
The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound (based on the speaker settings). Front Left Front Right Center (monaural) Surround Left Surround Right Surround (monaural or the surround components obtained by Pro Logic processing) Surround back left Surround back right Surround back (the surround back components obtained by 6.1 channel decoding) Example: Recording format (Front/ Surround): 3/2.1 Output channel: When surround speaker is set to "NO" (page 49) Sound Field: A.F.D. AUTO

1 2

3

4

56 7

8

9

q; qa qs

qd

SP.A SP.B A.DIRECT HDMI EQ D.RANGE ;PL IIx SW LFE SLEEP MULTI CH IN
L C R SL S SR SBL SB SBR

;DIGITAL EX DTS-ES

CAT OPT COAX MONO MEMORY 96/24 NEO:6 D.ASSIGN STEREO

M MEMORY

w;

ql

qk

qj

qh qg qf
N Preset station indicators

wa
Name
A SW

L R C SL SR S SBL SBR SB

Function
Lights up when sub woofer selection is set to "YES" (page 49) and the audio signal is output from the SUB WOOFER jack. Lights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced. Lights up according to the speaker system used. However, these indicators do not light up if the speaker output is turned off or if a headphone is connected. Lights up when ANALOG DIRECT is selected (page 66). Flashes when you select "HDMI V. ASSIGN" in the Video menu (page 81). Lights up when the equalizer is activated (page 47). Lights up when dynamic range compression is activated (page 47).

Name
H ;DIGITAL (EX)

Function
Lights up when Dolby Digital signals are input. "; DIGITAL EX" lights up when Dolby Digital Surround EX signals are decoded. Note When playing a Dolby Digital format disc, be sure that you have made digital connections and that INPUT MODE is not set to "ANALOG FIXED" (page 78). Lights up when DTS signals are input. "DTS-ES" lights up when DTS-ES signals are input. "DTS 96/24" lights up when the receiver is decoding DTS 96 kHz/24 bit signals. Note When playing a DTS format disc, be sure that you have made digital connections and that INPUT MODE is not set to "ANALOG FIXED" (page 78). Lights up when you select category mode to "ONE CAT". For details on presetting XM Radio station, see page 76. Lights up when INPUT MODE is set to "AUTO 2CH" and the source signal is a digital signal being input through the OPTICAL jack, or when INPUT MODE is set to "OPT FIXED" (page 78).

O Tuner indicators P D.ASSIGN

B LFE

Q NEO:6

SW L SL C R SR

C SP.A/SP.B

I DTS (-ES)/ (96/24)

D A.DIRECT E HDMI

F EQ G D.RANGE

J CAT

K OPT

R ;PL (II)/(IIx) Lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. "; PL II" lights up when the Pro Logic II Movie/Music/Game decoder is activated. "; PL IIx" lights up when the Pro Logic IIx Movie/Music/ Game decoder is activated. However, these indicators do not light up if both the center and surround speakers are set to "NO" (page 49) and you select a sound field using the A.F.D. button. Note Dolby Pro Logic IIx decoding does not function for DTS format signals or for signals with a sampling frequency of more than 48 kHz. S MULTI CH IN Lights up when MULTI CH IN is selected (page 40). T SLEEP Lights up when the sleep timer is activated (page 83).

continued

7US

8US

5

STR-DG800
Ver. 1.1

Rear panel
Getting Started

E COMPONENT VIDEO INPUT/ OUTPUT section
2 3 4 5 6
Green Blue Red

Remote commander
You can use the supplied remote to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate. You can also program the remote to control non-Sony audio/video components. For details, see "Programming the remote" (page 86).

1

DIGITAL
OPTICAL VIDEO 1 IN

HDMI
ASSIGNABLE DVD IN

ANTENNA
Y
S-VIDEO IN S-VIDEO IN S-VIDEO OUT S-VIDEO IN S-VIDEO OUT

COMPONENT VIDEO INPUT/ OUTPUT jack*

PB/CB /B-Y PR/CR /R-Y

L + ­

Connects to a DVD player, TV, or a satellite tuner. You can enjoy high quality image (page 25, 27, 28).

TV/SAT IN MD/ TAPE IN MD/ TAPE OUT DVD IN SA-CD/ CD IN COAXIAL ASSIGNABLE
(INPUT ONLY)

AM

XM
VIDEO IN VIDEO IN AUDIO IN VIDEO OUT AUDIO OUT VIDEO IN AUDIO IN VIDEO OUT AUDIO OUT VIDEO IN AUDIO IN VIDEO OUT

TV/ SAT IN

MONITOR
AUDIO IN SUR

TV/SAT IN SUB WOOFER

DVD IN

MONITOR OUT

L

L

L

L

ASSIGNABLE

COMPONENT VIDEO

R FRONT B SPEAKERS

F SPEAKER section
L

SIGNAL GND MONITOR OUT

R

TV/SAT DVD
L

R VIDEO 2

R VIDEO 1

R PRE OUT

L + ­ +

L ­ +

Connects to speakers (page 16).
­ AC OUTLET

RM-AAP008
wl wk
TV RM SET UP AV ?/1

L

L

L
CENTER

+
L R
OUT

­

?/1

1 AV ?/1 switch (on/standby) 2 ?/1 (on/standby)
switch

R
IN IN OUT

R
IN FRONT

R

R

SURROUND

SUR BACK

SUB WOOFER

CENTER

PHONO SA-CD/CD

MD/TAPE

MULTI CH IN

ZONE 2

R SURROUND BACK SPEAKERS

R SURROUND

R FRONT A

Connects to sub woofer (page 16). * You can watch the selected input image when you connect the MONITOR OUT jack to a TV monitor (page 25).
wj wh wg wf wd

SYSTEM STANDBY VIDEO 1 VIDEO 2 VIDEO 3 DVD
TV/SAT MD/TAPE SA-CD/CD TUNER PHONO MULTI CH SOURCE 2ND ZONE

3 4 5 6 7 8

A DIGITAL INPUT/OUTPUT section
Connects to a DVD player, etc. The COAXIAL jack provides a better COAXIAL IN quality of loud jack sound (page 26, 28). HDMI IN/ MONITOR OUT jack Connects to a DVD player, or a satellite tuner. The image and the sound are output to TV or a projector (page 30). OPTICAL IN/OUT jack

C AUDIO INPUT/OUTPUT section
White (L) Red (R)

2CH SLEEP

A.F.D.

MOVIE

MUSIC

AUDIO IN/ OUT jack

Connects to an MD deck or CD player, etc. (page 21).

CATEGORY MODE D. TUNING AUTO CAL

1 4

2 5 8 0/10
V B v

3 6 9
ENTER MEMORY TOOLS

9

White (L) Red (R) Black

MULTI CHANNEL INPUT jack

Connects to a Super Audio CD player or DVD player which has an analog audio jack for 7.1 channel sound (page 20).

7
ws
­ /­ ­ CLEAR >10 DISPLAY

q;

wa w; ql
RETURN/ EXIT
.

qa
B

White (L) Red (R)

B ANTENNA section
FM ANTENNA Connects to the FM wire antenna supplied with this receiver (page 32). Connects to the AM loop antenna supplied with this receiver (page 32). Connects to the XM connect-andplay antenna (not supplied with this receiver) (page 72).

PRE OUT jack Connects to an external power amplifier.

MENU
­ CATEGORY + REPLAY ADVANCE < <

AMP

qs qd

>

TUNING ­

TUNING +

m

D VIDEO/AUDIO INPUT/OUTPUT section
White (L) Red (R)

H
X

M

qf

DISC SKIP

x
TV CH PRESET

AM ANTENNA

AUDIO IN/ OUT jack

XM

Connects the video and audio jacks of a VCR or a DVD player (page 25, 26, 27, 28, 29).

TV VOL MASTER VOL

qk

MUTING

qg

DVD TOP MENU MENU

F1 TV/VIDEO

F2

qj
WIDE

qh

Yellow

VIDEO IN/ OUT jack* S-VIDEO IN/ OUT jack*

continued

9US

10US

Name
A AV ?/1

Function
Press to turn on or off the Sony audio/video components that the remote is programmed to operate. To turn the TV on or off, press TV(wj) and then press AV ?/1. If you press ?/1 (B) at the same time, it will turn off the receiver and other components (SYSTEM STANDBY). Note The function of the AV ?/1 switch changes automatically each time you press the input buttons (C). Press to turn the receiver on or off. To turn off all components, press ?/1 and AV ?/1 (A) at the same time (SYSTEM STANDBY).

Name

Function
Getting Started

Name
I Numeric buttons (number 5a))

Function
Press to ­ preset/tune to preset stations. ­ select track numbers of the CD player, DVD player, LD player, DAT deck, tape deck or MD deck. Press 0/10 to select track number 10. ­ select channel numbers of the VCR, satellite tuner, Bluray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press TV (wk), and then press the numeric buttons to select the TV channels. Press to enter the value after selecting a channel, disc or track using the numeric buttons. To enter the value of Sony TV, press TV (wk), and then press ENTER. Press to store a station. Press to display options applicable to the entire disc (e.g. disc protection), recorder (e.g. audio settings during recording), or multiple items on a list menu (e.g. erasing multiple titles). To display the options of Sony TV, press TV (wk), and then press TOOLS. Press AMP to light up the button, then press MENU (M) to display the menu of the receiver. Then, use the control buttons to perform menu operations. Press to display the menus of the VCR, DVD player, satellite tuner, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. on the TV screen. Then, use the control buttons to perform menu operations. To display the menus of Sony TV, press TV (wk), and then press MENU.

Name
N ./>

Function
Press to skip tracks of the VCR, CD player, VCD player, LD player, DVD player, MD deck, DAT deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO.

C Input buttons Press one of the buttons to select the component you want to use. When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components as follows. You can program the remote to control non-Sony components by changing the code. For details see "Programming the remote" (page 86).
Button VIDEO 1 VIDEO 2 VIDEO 3 DVD TV/SAT Assigned Sony component VCR (VTR mode 3) VCR (VTR mode 2) VCR (VTR mode 1) DVD player TV tuner

REPLAY < / Press to replay the previous ADVANCE < scene or fast forward the current scene of the VCR, DVD player, DVD/VIDEO COMBO, or DVD/HDD COMBO. CATEGORY +/­ m/M Press to select XM Radio category you want. Press to ­ search tracks in the forward/ backward direction of the DVD player, LD player, MD deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. ­ fast forward/rewind of the VCR, CD player, MD deck, DAT deck or tape deck. Press to start playback of the VCR, CD player, VCD player, LD player, DVD player, MD deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press to skip disc of the CD player, VCD player, DVD player, MD deck or LD player (multi-disc changer only). Press to pause playback or recording of the VCR, CD player, VCD player, LD player, DVD player, MD deck, DAT deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. (Also starts recording with components in recording standby.)

J ENTER

B ?/1

MEMORY K TOOLS

MD/TAPE MD deck SA-CD/CD Super Audio CD/CD player TUNER PHONO Built-in tuner Not assigned.

Ha)

D 2ND ZONE

Press 2ND ZONE to light up the button to select the command mode of the remote. Press to select the current input for the main receiver. Press to select sound fields (MOVIE, MUSIC). Press to activate the Auto Calibration function. Press to enter direct tuning mode.

L AMP

E SOURCE F MOVIE, MUSIC G AUTO CAL H D.TUNING

DISC SKIP

M MENU

X

11US

12US

6

STR-DG800
Ver. 1.1

Name
qf x

Function
Press to stop playback of the VCR, CD player, VCD player, LD player, DVD player, MD deck, DAT deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press to scan a station. Press TV (wk), and then press TV CH +/­ to select preset TV channels.

Name
R TV VOL +/­ MASTER VOL +/­ MUTING

Function
Press TV (wk) and then press TV VOL +/­ to adjust the TV volume level. Press to adjust the volume level of all speakers at the same time. Press to mute the sound. To mute the sound of the TV, press TV (wk) and then press MUTING. Press to ­ return to the previous menu. ­ exit the menu while the menu or on-screen guide of the VCR, DVD player, LD player, Blu-ray disc recorder, PSX or satellite tuner is displayed on the TV screen. To return to the previous menu of Sony TV, press TV (wk), and then press RETURN/ EXIT O. After pressing AMP (L), then MENU M for receiver operation DVD TOP MENU qj or DVD MENU qj, press the control button V, v, B or b to select the settings. When you press DVD TOP MENU or DVD MENU, press the control button to enter the selection. Press to select information displayed on the TV screen of the VCR,VCD player, satellite tuner, CD player, DVD player, MD deck, Bluray disc recorder, PSX, DVD/ VIDEO COMBO, or DVD/ HDD COMBO.

Name
V -/--

Function
Press to select the channel entry mode, either one or two digits of the Blu-ray disc recorder or satellite tuner. To select the channel mode of the TV, press TV (wk) and then press -/--. Press to select track numbers over 10 of the VCR, satellite tuner, CD player or MD deck, tape deck, TV, Blu-ray disc recorder or PSX. Press to ­ clear a mistake when you press the incorrect numeric button. ­ return to continuous playback, etc. of the satellite tuner, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press to select the category mode for XM radio. Press to activate the Sleep Timer function and the duration which the receiver turns off automatically. Press to select 2CH STEREO mode. Press to select A.F.D. mode. Press to select the audio directly from the components connected to MULTI CH IN jacks (page 40). Press to light up the button. It changes the remote key function to activate the buttons with orange printing. It also activate the TOOLS (qa), MENU (qd), RETURN/EXIT O (ql), and DISPLAY (wa) buttons to perform menu operations for Sony TVs only. Press to set-up the remote.

Notes
· Some functions explained in this section may not work depending on the model. · The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

Getting Started

TUNING +/­

>10

O TV CH +a)/­

PRESET +a)/­ Press to select ­ preset stations. ­ preset channels of the VCR, satellite tuner, Blu-ray disc recorder, DVD, DVD/ VIDEO COMBO, or DVD/ HDD COMBO.

S RETURN/ EXIT O

CLEAR

P F1, F2

Press to select the media (for DVD/VIDEO COMBO and DVD/HDD COMBO models only). Press TV (wk), and then press WIDE to select the wide picture mode. Press to select the media (for DVD/VIDEO COMBO and DVD/HDD COMBO models only) Press TV (wk) and then press TV/VIDEO to select the input signal (TV input or video input). Press to display the DVD title of the DVD player on the TV screen. Then, use the control buttons to perform menu operations. Press to display the menu of the DVD player on the TV screen. Then, use the control buttons to perform menu operations. T Control buttons

W CATEGORY
MODE

WIDE

X SLEEP

Y 2CH Z A.F.D. wj MULTI CH

TV/VIDEO

U DISPLAY

Q DVD TOP MENU

wk TV

DVD MENU

wl RM SET UP
a)

The number 5, PRESET +, TV CH +, and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.

continued

13US

14US

E2, MY, SP, TW model:
Name Function
The current status of the selected component or a list of selectable items appears here (page 6). Lights up when multi channel audio is decoded (page 42).

Name
S SUR BACK DECODING

Function
Press to select the decoding mode for the surround back signals (page 52). Press to select the receiver to turn off automatically at a specific time (page 76). Press to adjust the brightness of the display (page 59). Press to store a station or enter the selection when selecting the settings (page 33). To connect a camcorder or video game (page 28, 39). Connects to a headphone (page 87).

Getting Started

G Display

Getting Started

Description and location of parts
Front panel
1 2 34 56 7 8 9 q; qa qs
H MULTI CHANNEL DECODING lamp

T SLEEP

U DIMMER

I Remote sensor Receives signals from remote commander. J DISPLAY Press to select information displayed on the display (page 75). Press to select the input mode when the same components are connected to both digital and analog jacks (page 71). Turn to adjust the volume level of all speakers at the same time (page 38, 39, 41, 42). Press to listen to high quality analog sound (page 65). Press to select the audio directly from the components connected to the MULTI CH IN jacks (page 39). Turn to select the input source to playback (page 39, 41, 42, 65, 67, 70, 71, 75, 76). Press to select sound fields for movie or music (page 62). Press to select A.F.D. mode (page 60). Press to select 2CH STEREO mode (page 65, 66). V MEMORY/ ENTER

?/1
MASTER VOLUME
MULTI CHANNEL DECODING

K INPUT MODE

TONE MODE

TUNING MODE

DISPLAY

INPUT MODE

­ TONE + SPEAKERS (OFF/A/B/A+B)

­ TUNING +

INPUT SELECTOR

W VIDEO 3 IN/ PORTABLE AV IN jacks X PHONES jack

AUTO CAL MIC
MEMORY/ ENTER DIMMER SLEEP SUR BACK DECODING 2CH A.F.D. MOVIE

MUSIC

MULTI CH IN

DIRECT

L MASTER VOLUME

VIDEO 3 IN/PORTABLE AV IN PHONES

VIDEO

L AUDIO R

DIGITAL(OPT)

M DIRECT

Y AUTO CAL MIC Connects to the supplied jack ECM-AC2 optimizer microphone for the Auto Calibration function (page 35).

wg wf

wd

ws wa w; ql qk qj

qh

qg

qf

qd

N MULTI CH IN

PUSH

O INPUT SELECTOR

To remove the cover Press PUSH. When you remove the cover, keep it out of reach from children.

Name
A ?/1

Function
Press to turn the receiver on or off (page 32, 41, 42, 66, 91). Press to select OFF, A, B, A+B of the front speakers (page 34). Press to select Equalizer mode (page 46). Turn to adjust the EQUALIZER menu parameters (page 46, 51). Press to select the tuning mode (page 70, 91). Turn to scan a station (page 67, 69).
P MOVIE, MUSIC Q A.F.D. R 2CH

B SPEAKERS (OFF/A/B/A+B) C TONE MODE D TONE +/­

E TUNING MODE F TUNING +/­

4GB

5GB

7

STR-DG800
Ver. 1.1

About the indicators on the display
1 2 3 4 56 7 8 9 q; qa qs

Name
L MEMORY

Function
Lights up when a memory function, such as Preset Memory (page 69), etc., is activated. Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations, see page 68. Lights up when using the receiver to tune in radio stations (page 66), etc. Lights up when the digital assign function is used for selected input. Lights up when DTS Neo:6 Cinema/Music decoder is activated (page 61).

Name
T Playback channel indicators

Function
The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound (based on the speaker settings). Front Left Front Right Center (monaural) Surround Left Surround Right Surround (monaural or the surround components obtained by Pro Logic processing) Surround back left Surround back right Surround back (the surround back components obtained by 6.1 channel decoding) Example: Recording format (Front/ Surround): 3/2.1 Output channel: When surround speaker is set to "NO" (page 48) Sound Field: A.F.D. AUTO

Getting Started

SP.A SP.B A.DIRECT HDMI EQ D.RANGE ;PL IIx SW LFE SLEEP MULTI CH IN
L C R SL S SR SBL SB SBR

;DIGITAL EX DTS-ES
96/24 NEO:6

OPT COAX MONO MEMORY D.ASSIGN STEREO

M Preset station indicators

ql

qk

qj

qh

qg qf qd

N Tuner indicators O D.ASSIGN

w;
Name
A SW

L R C SL SR S SBL SBR SB

Function
Lights up when sub woofer selection is set to "YES" (page 48) and the audio signal is output from the SUB WOOFER jack. Lights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced. Lights up according to the speaker system used. However, these indicators do not light up if the speaker output is turned off or if a headphone is connected. Lights up when ANALOG DIRECT is selected (page 65). Flashes when you select "HDMI V. ASSIGN" in the Video menu (page 74). Lights up when the equalizer is activated (page 46). Lights up when dynamic range compression is activated (page 46).

Name
H ;DIGITAL (EX)

Function
Lights up when Dolby Digital signals are input. "; DIGITAL EX" lights up when Dolby Digital Surround EX signals are decoded. Note When playing a Dolby Digital format disc, be sure that you have made digital connections and that INPUT MODE is not set to "ANALOG FIXED" (page 71). Lights up when DTS signals are input. "DTS-ES" lights up when DTS-ES signals are input. "DTS 96/24" lights up when the receiver is decoding DTS 96 kHz/24 bit signals. Note When playing a DTS format disc, be sure that you have made digital connections and that INPUT MODE is not set to "ANALOG FIXED" (page 71). Lights up when INPUT MODE is set to "AUTO 2CH" and the source signal is a digital signal being input through the OPTICAL jack, or when INPUT MODE is set to "OPT FIXED" (page 71). Lights up when INPUT MODE is set to "AUTO 2CH" and the source signal is a digital signal being input through the COAXIAL jack, or when INPUT MODE is set to "COAX FIXED" (page 71).
P NEO:6

B LFE

C SP.A/SP.B

I DTS (-ES)/ (96/24)

D A.DIRECT E HDMI

F EQ G D.RANGE

J OPT

Q ;PL (II)/(IIx) Lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. "; PL II" lights up when the Pro Logic II Movie/Music/Game decoder is activated. "; PL IIx" lights up when the Pro Logic IIx Movie/Music/ Game decoder is activated. However, these indicators do not light up if both the center and surround speakers are set to "NO" (page 48) and you select a sound field using the A.F.D. button. Note Dolby Pro Logic IIx decoding does not function for DTS format signals or for signals with a sampling frequency of more than 48 kHz. R MULTI CH IN Lights up when MULTI CH IN is selected (page 39). S SLEEP Lights up when the sleep timer is activated (page 76).

SW L SL C R SR

K COAX

6GB

7GB

Rear panel
1 2 3 4 5 6

E COMPONENT VIDEO INPUT/ OUTPUT section
Green Blue

Remote commander
You can use the supplied remote to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate. You can also program the remote to control non-Sony audio/video components. For details, see "Programming the remote" (page 79).
Getting Started

DIGITAL
OPTICAL VIDEO 1 IN

HDMI
ASSIGNABLE DVD IN

ANTENNA
Y
S-VIDEO IN S-VIDEO IN S-VIDEO OUT S-VIDEO IN S-VIDEO OUT

COMPONENT VIDEO INPUT/ OUTPUT jack*

PB/CB /B-Y PR/CR /R-Y

L + ­

Red

Connects to a DVD player, TV, or a satellite tuner. You can enjoy high quality image (page 24, 26, 27).

TV/SAT IN MD/ TAPE IN MD/ TAPE OUT DVD IN SA-CD/ CD IN COAXIAL ASSIGNABLE
(INPUT ONLY)

AM

VIDEO IN

VIDEO IN AUDIO IN

VIDEO OUT AUDIO OUT

VIDEO IN AUDIO IN

VIDEO OUT AUDIO OUT

VIDEO IN AUDIO IN

VIDEO OUT

TV/ SAT IN

MONITOR
AUDIO IN SUR

TV/SAT IN SUB WOOFER

DVD IN

MONITOR OUT

L

L

L

L

ASSIGNABLE

R FRONT B
SPEAKERS

COMPONENT VIDEO

F SPEAKER section
L

SIGNAL GND MONITOR OUT

R

TV/SAT DVD
L

R VIDEO 2

R VIDEO 1

R PRE OUT

L + ­ +

L ­ +

Connects to speakers (page 15).
­ AC OUTLET

RM-AAP009
wl wk
TV RM SET UP AV ?/1

L

L

L
CENTER

+
L R
OUT

­

?/1

1 AV ?/1 switch (on/standby) 2 ?/1 (on/standby)
switch

R
IN IN OUT

R
IN FRONT

R

R

SURROUND

SUR BACK

SUB WOOFER

CENTER

PHONO SA-CD/CD

MD/TAPE

MULTI CH IN

ZONE 2

R SURROUND BACK SPEAKERS

R SURROUND

R FRONT A

Connects to sub woofer (page 15). * You can watch the selected input image when you connect the MONITOR OUT jack to a TV monitor (page 24).
wj wh wg wf wd

SYSTEM STANDBY VIDEO 1 VIDEO 2 VIDEO 3 DVD
TV/SAT MD/TAPE SA-CD/CD TUNER PHONO MULTI CH SOURCE ZONE 2

3 4 5 6 7 8

A DIGITAL INPUT/OUTPUT section
OPTICAL IN/OUT jack Connects to a DVD player, etc. The COAXIAL jack provides a better COAXIAL IN quality of loud jack sound (page 25, 27). HDMI IN/ MONITOR OUT jack Connects to a DVD player, or a satellite tuner. The image and the sound are output to TV or a projector (page 29).

C AUDIO INPUT/OUTPUT section
White (L) Red (R)

2CH

A.F.D.

MOVIE

MUSIC

AUDIO IN/ OUT jack

Connects to an MD deck or CD player, etc. (page 20).

SLEEP FM MODE D. TUNING AUTO CAL

1 4

2 5 8 0/10
V B v

3 6 9
ENTER MEMORY TOOLS

9

White (L) Red (R) Black

MULTI CHANNEL INPUT jack

Connects to a Super Audio CD player or DVD player which has an analog audio jack for 7.1 channel sound (page 19).

7
ws
­ /­ ­ CLEAR >10 DISPLAY

q;

wa w; ql
RETURN/ EXIT
.

qa
B

White (L) Red (R)

B ANTENNA section
FM ANTENNA Connects to the FM wire antenna supplied with this receiver (page 31). Connects to the AM loop antenna supplied with this receiver (page 31).

PRE OUT jack Connects to an external power amplifier.

MENU
REPLAY ADVANCE < <

AMP

qs qd

>

TUNING ­

TUNING +

m

D VIDEO/AUDIO INPUT/OUTPUT section
White (L) Red (R)

H
X

M

qf

DISC SKIP

x
TV CH PRESET

AM ANTENNA

AUDIO IN/ OUT jack

Connects the video and audio jacks of a VCR or a DVD player (page 24, 25, 26, 27, 28).

TV VOL MASTER VOL

qk

MUTING

qg

DVD TOP MENU MENU

F1 TV/VIDEO

F2

qj
WIDE

qh

Yellow

VIDEO IN/ OUT jack* S-VIDEO IN/ OUT jack*

continued

8GB

9GB

8

STR-DG800
Ver. 1.1

Name
A AV ?/1

Function
Press to turn on or off the Sony audio/video components that the remote is programmed to operate. To turn the TV on or off, press TV(wk) and then press AV ?/1. If you press ?/1 (B) at the same time, it will turn off the receiver and other components (SYSTEM STANDBY). Note The function of the AV ?/1 switch changes automatically each time you press the input buttons (C). Press to turn the receiver on or off. To turn off all components, press ?/1 and AV ?/1 (A) at the same time (SYSTEM STANDBY).

Name

Function

Name
I Numeric buttons (number 5a))

Function
Press to ­ preset/tune to preset stations. ­ select track numbers of the CD player, DVD player, LD player, DAT deck, tape deck or MD deck. Press 0/10 to select track number 10. ­ select channel numbers of the VCR, satellite tuner, Bluray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press TV (wk), and then press the numeric buttons to select the TV channels. Press to enter the value after selecting a channel, disc or track using the numeric buttons. To enter the value of Sony TV, press TV (wk), and then press ENTER. Press to store a station. Press to display options applicable to the entire disc (e.g. disc protection), recorder (e.g. audio settings during recording), or multiple items on a list menu (e.g. erasing multiple titles). To display the options of Sony TV, press TV (wk), and then press TOOLS. Press AMP to light up the button, then press MENU (M) to display the menu of the receiver. Then, use the control buttons to perform menu operations. Press to display the menus of the VCR, DVD player, satellite tuner, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. on the TV screen. Then, use the control buttons to perform menu operations. To display the menus of Sony TV, press TV (wk), and then press MENU.

Name
N ./>

Function
Press to skip tracks of the VCR, CD player, VCD player, LD player, DVD player, MD deck, DAT deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO.

C Input buttons Press one of the buttons to select the component you want to use. When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components as follows. You can program the remote to control non-Sony components by changing the code. For details see "Programming the remote" (page 79).
Button VIDEO 1 VIDEO 2 VIDEO 3 DVD TV/SAT Assigned Sony component VCR (VTR mode 3) VCR (VTR mode 2) VCR (VTR mode 1) DVD player TV tuner

Getting Started

REPLAY < / Press to replay the previous ADVANCE < scene or fast forward the current scene of the VCR, DVD player, DVD/VIDEO COMBO, or DVD/HDD COMBO. m/M Press to ­ search tracks in the forward/ backward direction of the DVD player, LD player, MD deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. ­ fast forward/rewind of the VCR, CD player, MD deck, DAT deck or tape deck. Press to start playback of the VCR, CD player, VCD player, LD player, DVD player, MD deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press to skip disc of the CD player, VCD player, DVD player, MD deck or LD player (multi-disc changer only). Press to pause playback or recording of the VCR, CD player, VCD player, LD player, DVD player, MD deck, DAT deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. (Also starts recording with components in recording standby.)

J ENTER

B ?/1

MEMORY K TOOLS

MD/TAPE MD deck SA-CD/CD Super Audio CD/CD player TUNER PHONO Built-in tuner Not assigned.

Ha)

D ZONE 2

Press ZONE 2 to light up the button to select the command mode of the remote. Press to select the current input for the main receiver. Press to select sound fields (MOVIE, MUSIC). Press to activate the Auto Calibration function. Press to enter direct tuning mode.

DISC SKIP

L AMP

E SOURCE F MOVIE, MUSIC G AUTO CAL H D.TUNING

X

M MENU

continued

10GB

11GB

Name
qf x

Function
Press to stop playback of the VCR, CD player, VCD player, LD player, DVD player, MD deck, DAT deck, tape deck, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press to scan a station. Press TV (wk), and then press TV CH +/­ to select preset TV channels.

Name
R TV VOL +/­ MASTER VOL +/­ MUTING

Function
Press TV (wk) and then press TV VOL +/­ to adjust the TV volume level. Press to adjust the volume level of all speakers at the same time. Press to mute the sound. To mute the sound of the TV, press TV (wk) and then press MUTING. Press to ­ return to the previous menu. ­ exit the menu while the menu or on-screen guide of the VCR, DVD player, LD player, Blu-ray disc recorder, PSX or satellite tuner is displayed on the TV screen. To return to the previous menu of Sony TV, press TV (wk), and then press RETURN/ EXIT O. After pressing AMP (L), then MENU M for receiver operation DVD TOP MENU qj or DVD MENU qj, press the control button V, v, B or b to select the settings. When you press DVD TOP MENU or DVD MENU, press the control button to enter the selection. Press to select information displayed on the TV screen of the VCR,VCD player, satellite tuner, CD player, DVD player, MD deck, Bluray disc recorder, PSX, DVD/ VIDEO COMBO, or DVD/ HDD COMBO.

Name
V -/--

Function
Press to select the channel entry mode, either one or two digits of the Blu-ray disc recorder or satellite tuner. To select the channel mode of the TV, press TV (wk) and then press -/--. Press to select track numbers over 10 of the VCR, satellite tuner, CD player or MD deck, tape deck, TV, Blu-ray disc recorder or PSX. Press to ­ clear a mistake when you press the incorrect numeric button. ­ return to continuous playback, etc. of the satellite tuner, Blu-ray disc recorder, PSX, DVD/VIDEO COMBO, or DVD/HDD COMBO. Press to select FM monaural or stereo reception. Press to activate the Sleep Timer function and the duration which the receiver turns off automatically. Press to select 2CH STEREO mode. Press to select A.F.D. mode. Press to select the audio directly from the components connected to MULTI CH IN jacks (page 39). Press to light up the button. It changes the remote key function to activate the buttons with orange printing. It also activate the TOOLS (qa), MENU (qd), RETURN/EXIT O (ql), and DISPLAY (wa) buttons to perform menu operations for Sony TVs only. Press to set-up the remote.

Notes
· Some functions explained in this section may not work depending on the model. · The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

Getting Started

TUNING +/­

>10

O TV CH +a)/­

PRESET +a)/­ Press to select ­ preset stations. ­ preset channels of the VCR, satellite tuner, Blu-ray disc recorder, DVD, DVD/ VIDEO COMBO, or DVD/ HDD COMBO.

S RETURN/ EXIT O

CLEAR

P F1, F2

Press to select the media (for DVD/VIDEO COMBO and DVD/HDD COMBO models only). Press TV (wk), and then press WIDE to select the wide picture mode. Press to select the media (for DVD/VIDEO COMBO and DVD/HDD COMBO models only) Press TV (wk) and then press TV/VIDEO to select the input signal (TV input or video input). Press to display the DVD title of the DVD player on the TV screen. Then, use the control buttons to perform menu operations. Press to display the menu of the DVD player on the TV screen. Then, use the control buttons to perform menu operations. T Control buttons

W FM MODE X SLEEP

WIDE

Y 2CH Z A.F.D. wj MULTI CH

TV/VIDEO

U DISPLAY

Q DVD TOP MENU

wk TV

DVD MENU

wl RM SET UP
a)

The number 5, PRESET +, TV CH +, and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.

12GB

13GB

9

STR-DG800
Ver. 1.1

SECTION 2 DISASSEMBLY

Note : This set can be disassemble according to the following sequence.

SET 2-1. CASE (Page 10)

2-2.

FRONT PANEL SECTION (Page 11)

2-3.

BACK PANEL SECTION (Page 11)

2-6.

STANDBY BOARD (Page 13)

2-4.

DIGITAL BOARD (Page 12) MAIN BOARD SECTION (Page 12)

2-5.

Note : Follow the disassembly procedure in the numerical order given.

2-1. CASE

2 two screws (case 3 TP2)

3 two screws (+BVTP 3 × 8)

4 case

1 two screws (case 3 TP2)

10

STR-DG800
Ver. 1.1

2-2. FRONT PANEL SECTION

5 two screws (+BVTP 3 × 8) 1 CNP2000 (4P)

2 CNP4092 (4P)

4 CNS505 (27 core) 3 CNP4091 (5P) 7 front panel section 6 six screws (+BVTP 3 × 8)

2-3. BACK PANEL SECTION
qd screw (+BVTP 3 × 8) qj two screws (+BVTP 3 × 8) qh eight screws (+BVTP 3 × 8) 2 CN3002 (4P) 1 CNP901 (2P) qg five screws (+BVTP 3 × 8)

qk back panel section

qs CNP2850 (7P)

3 CNP2101 (4P)

9 CNP2208 (7P) 0 CNP2209 (3P) qa CNP2300 (9P)

qf four screws (+BVTP 3 × 8) 4 CNS509 (21 core) 5 CNS508 (11 core) 8 CNS803 (5 core) 6 CNS503 (9 core) 7 CN103 (3 core)

11

STR-DG800

2-4. DIGITAL BOARD
2 CNP503 (5P) 1 CNP505 (10P)

3 CNP504 (7P)

5 DIGITAL board

4 screw (+BVTP 3 × 8)

2-5. MAIN BOARD SECTION
7 screw (+BV3 (3-CR)) 6 two screws (+BV3 (3-CR)) 4 CN908 (5P) 5 CNP802 (5P) 8 two screws (+BV3 (3-CR)) 2 CNP817 (6P)

3 CNP815 (3P)

1 CN851 (4P)

9 MAIN board section

12

STR-DG800

2-6. STANDBY BOARD
2 screw (+BVTP 3 × 8) 3 STANDBY board

1 CNP905 (2P) 4 CNP816 (4P)

13

STR-DG800
Ver. 1.1

SECTION 3 TEST MODE
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed. * Procedure: While depressing the [SPEAKERS $OFF/A/B/A+B%] and the [DIRECT] buttons simultaneously, press the ?/1 button to turn on the main power. The model name, destination and the software version are displayed for a moment.

FACTORY PRESET MODE
* All preset contents are reset to the default setting. * Procedure: While depressing the [TONE MODE] and the [DIRECT] buttons simultaneously, press the ?/1 button to turn on the main power. The message "FACTORY" appears for a moment and the present contents are reset to the default values.

AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Turn the [INPUT SELECTOR] control to set AM and press the ?/1 button to turn off the main power. While depressing the [CATEGORY MODE] (US, CND) or [DIMMER] (E2, MY, SP, TW) button, press the ?/1 button to turn on the main power. Either the message "9k STEP" or "10k STEP" appears for a moment and select the desired step.

KEY CHECK MODE
* Button check * Procedure: While depressing the [SPEAKERS $OFF/A/B/A+B%] and the [MULTI CH IN] buttons simultaneously, press the ?/1 button to turn on the main power. Either the message "REST 15" appears. Every pressing of any button other than the ?/1 counts down the buttons. The buttons which are already counted once are not counted again. When all buttons are pressed "REST 00" appears.

COMMAND MODE SELECTION MODE VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested. When this test is activated, all segments light on at the same time, then each segment lights on one after another. * Procedure: While depressing the [SPEAKERS $OFF/A/B/A+B%] and the [DISPLAY] buttons simultaneously, press the ?/1 button to turn on the main power. 1. ALL segments light on.
SW

* The command mode (AV1 or AV2) of the remote commander can be selected. * Procedure: While depressing the [INPUT MODE] button, press the ?/1 button to turn on the main power. Either the message "C.MODE.AV 1" or "C.MODE.AV 2" appears for a moment and select the desired mode.

SP.A SP.B A.DIRECT HDMI EQ D.RANGE LFE SLEEP MULTI CH IN 1 2 D D PL II x
C
S

D DDIGITAL EX DTS-ES D DD + CAT OPT COAX MONO NIGHT DTS-HD 96/24 NEO:6 kHz MHz D.ASSIGN STEREO

MEMORY

RDS

L
SL

R
SR
SBR

SBL SB

dB f t. m

[MULTI CHANNEL DECODING] LED light on. 2. Turn the [INPUT SELECTOR] control, confirm display.
SW L
S
SB

LFE
R

A A.DIRECT HDMI EQ D D PL x SLEEP 1

EX DTS-HD

[MULTI CHANNEL DECODING] LED light on. 3. Turn the [INPUT SELECTOR] control, confirm display.
-ES 96/24 D DD + Hz OPT MONO RDS

m

[MULTI CHANNEL DECODING] LED light on. 4. Turn the [INPUT SELECTOR] control, all segments light off. [MULTI CHANNEL DECODING] LED light off.

SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the [2CH] button, press the ?/1 button to turn on the main power. The message "S.F. INITIALIZE" appears for a moment and initialization is performed.

14

STR-DG800 SECTION 4 DIAGRAMS
4-1. BLOCK DIAGRAM -- TUNER/AUDIO SECTION --
DVD TV/SAT VIDEO 2 VIDEO 1 VIDEO 3 IN/ PORTABLE AV IN AUDIO L J2554 (1/2) -2 -3 R J4091 (2/2)

AUDIO IN L -1 -2 R

AUDIO IN L -3 -4 J2552 R

AUDIO IN L -1 -2 R

AUDIO OUT L -3 -4 J2553 R

AUDIO IN L -3 -4 R

AUDIO OUT L -5 -6 R

R­CH

R­CH

R­CH

R­CH

R­CH

R­CH

R­CH

INPUT SELECT IC2560 MD/TAPE 12 10 8 4 6 2 V3L V1L V2L TV L DVD L AU INL V2 OUTL SEL SW V1 OUTL 17 15 J302 AU OUTL 13 DIR FUNCTION SELECT IC401 ­7V +7V PHONO AMP IC301 5 44 45 22 23 32 33 26 27 41 42 3 -1 OUT L -2 R -3 L -4 IN R -1 L -2 PHONO IN R -3 L -4 SA-CD/CD IN R J301 -1 PRE OUT SUR L -2 R J2554 (2/2)

LOGIC

CLK

DA

22

23 46

68 AVEE

66 AVCC R­CH R­CH

US,CND MODEL XM L XM R XM REQ XM DBPOWER XM COMMAND XM DACMS XM RESET

38 28 R­CH SEL SW

7

1

XM SECTION (Page 18)

D

R­CH R­CH R­CH

L­CH R­CH

TN1 FM/AM TUNER UNIT L­CH 53 RDS DATA/XM COMMAND 52 RDS CLK/XM DPOWER ANALOG SW DATA 85 43 RDS SIG/XM REQ ANALOG SW CLK 71 76 STEREO 75 TUNED SYSTEM CONTROL 78 MUTE XM_RST 26 IC1101 (1/5) XM DACMS 47 74 S LATCH VOL DA 60 73 DO VOL CL 59 17 TUNER DATA/FL DATA 16 T.SERIAL CLK/FL CLK 70 SW RY 36

A

DIGITAL (Page 16) SECTION
RY2300

R­CH RELAY DRIVE Q2300 REAR RY L SEL R­CH 88 87 L­CH R­CH

FM 75 COAXIAL R­CH STEREO TUNED MUTING CE DO DATA CLOCK R­CH

ANTENNA AM

TU+10V

60 59

MCU I/F

SL SEL R­CH

85 84

SL­CH SR­CH

F

KEY/ DISPLAY/ HDMI SECTION (Page 19)

10

86

C­CH

E

FL DATA

13 12 C SEL SW SEL SBL­CH 81 SBR­CH 83 R­CH SBL SEL R­CH R­CH 82

R­CH

R­CH

R­CH

R­CH

R­CH R­CH R­CH

17 11 14 15 16 19 20

R­CH R­CH

J304 -1 L -2 R -3 L -4 R -5 L -6 R

J305 -1 -2 -3 L -4 R OUT ZONE 2 MULTI CH IN RY300 RELAY DRIVE Q300

POWER SECTION (Page 20) · Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : CD (ANALOG) · R­ch is omitted due to same as L­ch. · Abbreviation CND : Canadian model
J2551 SUB WOOFER PRE OUT

FRONT

SURROUND

SUR BACK

CENTER

SUB WOOFER

R­CH

54 SBL OUT

56

51

52

49

RY351

VIDEO SECTION (Page 17)

C

2ND ROOM

DIGITAL SECTION (Page 16)

B

SW OUT C OUT SL OUT L OUT

RELAY DRIVER Q351

STR-DG800

15

15

R­CH

STR-DG800

4-2. BLOCK DIAGRAM -- DIGITAL SECTION --
ADC IC1401 DSP IC1501 8CH DAC IC1452

AMP IC1403 VOUT5 10 3 1 L OUT

L-IN

1

L IN

ADC

LPF

AUDIO I/F

DOUT

15

18 SDI1

R-IN

R-CH

+5V-2 A.5V

SYS CLK

TUNER/ AUDIO SECTION (Page 15)

D1503

D1502

LRCK 13 BCK 14
RST

D1501

A

SD01 23 SD02 24 SD03 25

DATA3 47

DAC VOUT6 9 5 7 R-CH

AMP IC1405 VOUT1 DATA1 14 5 7 SL OUT

SD04 26 SCKOUT LRCKO BCKO
D1504

16

6 SCKOUT 14 LRCKO 19 BCKO 20

ADCC_INT

45

DAC VOUT2 13 3 1 R-CH

IC1353 MD/TAPE OUT (OPTICAL) DIN 3 IC1303 DVD -1 IN (COAXIAL) J1301 3 WAVE SHAPER 2 2 5

DIGITAL AUDIO I/F RECEIVER IC1301 20
XMCK

DOUT DIN2

AUDIO 24 CKOUT 13 BCK 14

69 GP8 22 KFSI0 29 BCKI2 28 LRCKI2 30 SDI2

MCLK1 9 MCLK2 12 CSO 44 WEO 45 OEO 43
D0-15 108,107,105 -102,99, 98,80 - 77,75 - 72

X1502 13.9MHz

AMP IC1404 SDRAM IC1502 DATA2 46 SCKOUT LRCKO BCKO DAC VOUT4 38 SCKI 41 LRCK 40 BCK AMP IC1406 VOUT7 11 5 7 SW OUT VOUT3 12 3 1 C OUT

B

8 IC1103 J1301 SA-CD/CD -2 IN (COAXIAL) IC1354 VIDEO 1 IN (OPTICAL) OUT 1 3 5 6 4 A B 14 2 3 WAVE SHAPER 2 4

SDIN INPUT DIN1 DATA DEMODULATOR

LRCK 15 DATAO 16

6 CS 17 WE 41 OE

TUNER/ AUDIO SECTION (Page 15)

D1301 Pa,Pb DETECTION C bit DETECTION DIN0 LOCK DETECTION ERROR 34

17 BCKI1 59 EXLOCK

DIGITAL ASSIGNABLE (INPUT ONLY)

SELECTOR IC1302 7 3

29 - 32,35 - 38, 16-13,10 - 7 D0-15

15 LRCKI1

A0-15 112,110,109,97 - 92, 85-82,66 - 64

24 - 27,42 - 44, 1 - 5,18 - 21 A0-15

MICROPROCESSOR I/F

16

5

7

SBL OUT

DATA4 31 DAC VOUT8 20 3 1 R-CH

IC1351 TV/SAT IN (OPTICAL) OUT 1

21 XOUT 8
BPSYNC CKSEL0 XSTATE

+2.6V VDDI
XMODE

22 XIN X1301 12.288MHz VDD +3.3V
CLK

IC1352 MD/TAPE IN (OPTICAL) DIGITAL (OPT) OUT 1 IC4081 OUT 1

+3.3V VDDE

38

37

36

35

33 NC

46

17

48 37 GP12
HCS HACN

SWITCH IC1503
ADCC_INT

BST 56
XRST PM HDOUT HDIN HCLK

5 6

2 1

LRCKO

33 34 35 36 37

MDO MDI MC ML RST

DO

CE

DI

68 VIDEO 3 IN/ PORTABLE AV IN

GP9

36 32 2 113 35 33 34

US,CND MODEL XM DAC MC XM DAC MDI

G

XM SECTION

95
DIR_CLK

96
DIR CE

97
DIR DI

98
DIR DO

94 100 93
CKSEL1 XSTATE XMODE

91 90
SELECT1 SELECT2

99
ERROR

1
DATAO

8
GP12

2
GP9

4 5 6 7 18 19 20
XRST PM HDOUT HDIN HCS HACN HCLK

92
BST SEL

57 3
ADCC_INT BST

10 12 13 14 15
PCM1609 RST PCM1609 ML PCM1609 MC/XMDAC MC PCM1609 MDI/XMDAC MDI PCM1609 MDO

· Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : CD (ANALOG) : CD (DIGITAL) : VIDEO · R-ch is omitted due to same as L-ch. · Abbreviation CND : Canadian model

(Page 18)

SYSTEM CONTROL IC1101 (2/5)

STR-DG800

16

16

STR-DG800
Ver. 1.1

4-3. BLOCK DIAGRAM -- VIDEO SECTION --
Y VIDEO AMP IC3721

14 VI(B-Y) IC3253 1 J3301 (1/2) Y TV/SAT PB/CB/B-Y IN (ASSIGNABLE) PR/CR/R-Y COMPONENT VIDEO J3301 (2/2) -1 -7 -2 RY3303 -3 -4 Y -5 -6 RELAY DRIVER Q3302 RY3304 RELAY DRIVER Q3301,3304 -9 RY3301 -8 PB/CB/B-Y MONITOR OUT COMPONENT VIDEO Y SYNC SEPARATION Q3701 38 39 34 32 36 37 VSYNC HSYNC CVBS/Y IN C IN SCL SDA SYNC SEPARATION 2 SWITCH Q3252 1 26 28 23 24 22 21 X3703 X3701 X3702 500kHz 3.5795MHz 4.43MHz 16 VI(R-Y)

VO(B-Y) 12 VO(R-Y) 11

E2,MY,SP MODEL

(R,Y) OUT (B,Y) IN

443/358

(B,Y) OUT

(R,Y) IN

SECAM REF 30 YOUT 18 U2OUT 7 V2OUT 6

VIDEO AMP IC3321 1 4 7

VIDEO BUFFER Q3651-3653 15 13 11 VOUT1 VOUT2 VOUT3

CERA

PR/CR/R-Y

XNTSC

VIDEO PROCESS IC3701

MUTE1

COMP SW1

COMP SW2

DVD PB/CB/B-Y IN (ASSIGNABLE) PR/CR/R-Y

RY3302

MUTE2

3

1O

VIDEO 1

-2 J3401 (2/3) VIDEO IN -2 VIDEO IN -1 VIDEO IN J4091 (1/2) J3403 (1/2)

INPUT SELECT IC3431 13 V1 IN 6dB AMP 75 DRIVER LD J3402 (1/2) 6dB AMP 3 TV 6dB AMP 75 DRIVER M.OUT 1 -1 VIDEO OUT MONITOR V1.OUT 15 VCC +5V-3 J3401 (1/3) -1 VIDEO OUT 33 34 88 89 87 86 UPCON UPCON CLK D595 OE D595 LAT D595 CLK D595 DATA SYSTEM CONTROL IC1101 (3/5)

IC3101 +VCC7V +7V 3 REG IC3102 +9V +9V 3 REG IC3103 +5V-3 +5V 3 REG IC3104 -5V-3 IC1602 (1/2) DATA VIDEO CONTROL 13 12 11 SIN 14 3 1 4 BUFFER 6 OSD ON IC3141 11 3 HDMI CONTROL OSD ON/OFF 12 CS MUTE -5V 3 REG 2 -VCC 1 +VCC 1 +15V 1 +VCC

VIDEO 1

DVD

5

TV/SAT

2ND ROOM 75 DRIVER V2.OUT 11 15 7 6 5 SW4 4 COMP SW1 3 COMP SW2 2 UP SEL 1 SW1 SW2 SW3

C

VIDEO 3 IN/ PORTABLE AV IN

-1 VIDEO -2 VIDEO IN

J3402 (2/2)

7 V2 IN 9

V3

(Page 15) TUNER/ AUDIO SECTION

FUSE DETECT 63 MODEL/CSMUTE 64

IC1601

SW2

SW3 SW4

SW1

SW5

VIDEO 2

VEE

-5V-3

10

4 6

14 OR

2

14 OE 13 LAT 12 CLK 11 9

D3431,3432 Y SWITCH IC2101

SOUT

UP-MUTE 1 V-MUTE 2 M-MUTE 15

SW2

SW3

SW4

SW1

VCC 6dB AMP 75 DRIVER 6dB AMP 75 DRIVER M.OUT 1 VEE V1.OUT 15

J2106 (2/2) -2 S-VIDEO IN Y G

13

V1 IN

+5V-3 J2106 (1/2) Y G -1 S-VIDEO OUT VIDEO 1 37 F IN VIDEO BUFFER Q3601,3604 2 AD IN 23 26 19 17 Y/C SELECT IC3751 AYO 9 Y AMP Q3621 Y AMP Q3631 Y PROCESS Q3622,3623,3647 C PROCESS Q3624,3632,3633 5 3 12 13 11 10 9 6 A B C 4 Y AMP Q3673,3674 C AMP Q3675,3676

VIDEO 1

PNR

MOD1

C

C -5V-3

G

SW3

SW1

SW2

J2105 (1/2) -1 S-VIDEO IN Y G

SW4

SW5

10

4

6

14

2

Y/C SEPARATION IC3601

NTPL1

MOD2

G

TV 3 LD 5 V3 7 V2 IN 9

ACO 7

14

DVD

SW2

SW3

SW4

SW1

C

G

J2105 (2/2) -2 S-VIDEO IN Y G 13 V1 IN

C SWITCH IC2102 6dB AMP 75 DRIVER 6dB AMP 75 DRIVER M.OUT 1 VEE -5V-3 V1.OUT 15 MONITOR Y/IN MONITOR C/IN VCC +5V-3 MONITOR V/IN 12 2 5

SW5

VIDEO SELECT IC3651 14 15 4 IC3731 VIDEO AMP Q3671,3672

VIDEO MUTE CONTROL IC3671 7 VIN3 VOUT3 11

J3401 (3/3)

-3 VIDEO OUT MONITOR

TV/SAT

C

G

SW3

SW4

SW1

SW5

TV 3 LD 5 V3 7 V2 IN 9

4 1 SWITCH Q3731

VIN2 VIN1

VOUT2 VOUT1

13 15

Y

G

J2104 S-VIDEO OUT

MONITOR

SW2

C

G

CS MUTE

10

4

6

14

2

11 10 9 6 A B C

SYNC 1 SEPARATION 2

3 MUTE1 MUTE Q3677,3678

10 MUTE2

OR D2102,2103

· Signal path : VIDEO · Abbreviation E2 : 120V AC area in E model MY : Malaysia model SP : Singapore model

SW3

SW4

SW1

STR-DG800

SW2

SW5

17

17

STR-DG800

4-4. BLOCK DIAGRAM -- XM SECTION (US, CND MODEL) --
XM DIGITAL TRANSCEIVER IC102 SCTXOUT 3 SCRXIN 5 18 COMRXP 19 COMRXT 2 3 +D ­D 23 COMTXP 22 COMTXM COMMSEL 7 IRQ 9 XM64FS XMDATA XMFS XM256FS

3 12 11 2 6 7 5 4 9 18 XMCOMMAND XMREQ BUFFER IC103 8 17 XM MIXMI XM MIXMO

H

KEY/DISPLAY/HDMI SECTION (Page 19)

J101 XM

26 OSCOUT X101 45.158MHz 1 BCK 2 DATA 3 LRCK 16 SCK MD 13 MC 14 ML 15 VOUTL 7 VOUTR 8 D/A CONVERTER IC105 RESET 11 RESET Q101,104 6 2 XM DACMDI XM DACMC

28 OSCIN

I2SSCLK 39 I2SDATA 37 I2SLRCLK 41 I2SOCLK 43

G

(Page 16) DIGITAL SECTION
XMDACMS 7 1 XM AMP IC104 XM RESET DBPOWER F40 XML XMR

D

TUNER/AUDIO SECTION (Page 15)

1 XM+5.3V 4 XM5.3V REG 2 IC106 IC107 XM+5V IC101 XM+3.3V XM+3.3V 3 REG 1 XM+5V 3 REG 1

RECT D104

AC1

AC2

STR-DG800

18

18

STR-DG800

4-5. BLOCK DIAGRAM -- KEY/DISPLAY/HDMI SECTION --
MIC AMP IC2000 J2000 AUTO CAL MIC D2014 5 1 X1101 24MHz EEPROM IC1131 SDA 5 SCL 6 S141 I/ I 38 ADCC 83 X1 82 X0 SIRCS 54 29 SDA 30 SCL ENC A 31 ENC B 32 56 POWER KEY VOL ENC A 65 VOL ENC B 64 CNS504 1 2 7 6 5 8 9 FLASH1 FLASH2 MD2 MD0 RESET SCL SDA 28 27 51 49 FLASH1/XM_TX FLASH2/XM_RX MD2 MD0 TUNING A 21 TUNING B 22 1 3 RV105 TUNING +/1 3 RV103 MASTER VOLUME FL LAT 9 FL CLK 25 FL RESET 24 SIRCS 1 OUT REMOTE CONTROL RECEIVER IC103 RV104 INPUT SELECTOR LATCH CLK RESET DATA X101 8MHz 19 17 9 15 P51 P17 RESET P15 PD4 41 I I PD0 45 P97 I P60 46 I 77 FL101 VACUUM FLUORESCENT DISPLAY SYSTEM CONTROL IC1101 (4/5)

FL DISPLAY DRIVER IC100

2 XIN 3 XOUT

1 3

P47 37

LED DRIVER Q101

D101 MULTI CHANNEL DECODING

US,CND MODEL

XM SECTION (Page 18)

H

XM MIXMO XM MIXMI

FL DATA

E

TUNER/ AUDIO SECTION (Page 15)

FLASH PROGRAMMING

TONE EN A 46 TONE EN B 45

1 3

RV101 TONE +/-

+3.3V (STBY) 2 RESET IC1111 1 77 RSTX

A/D1 39 A/D2 40 SW NETWORK S100-107

SW NETWORK S110-116

· Abbreviation CND : Canadian model
CN5001 1 3 4 6 7 9 DVD IN 10 (ASSIGNABLE) 12 15 16 19 13 18 CN5002 1 3 4 6 7 9 TV/SAT IN 10 (ASSIGNABLE) 12 15 16 19 13 18 CN5003 1 3 4 6 7 MONITOR OUT 9 10 12 15 16 19 13 18 DATA2+ DATA2­ DATA1+ DATA1­ DATA0+ DATA0­ CLOCK+ CLOCK­ SCL(5V) SDA(5V) HOT PLUG DET CEC +5V POWER 77 76 74 73 71 70 68 67 64 63 62

HDMI RECEIVER/TRANSCEIVER IC5001 A24 B24 A23 B23 A22 B22 A21 B21 SCL2 SDA2 HPD2 IC1602 (2/2)

HDMI CONTROL

CTL(HDMI) 7 PRE(HDMI) 6 OEB(HDMI) 5 SI(HDMI) 4

DATA2+ DATA2­ DATA1+ DATA1­ DATA0+ DATA0­ CLOCK+ CLOCK­ SCL(5V) SDA(5V) HOT PLUG DET CEC +5V POWER DATA2+ DATA2­ DATA1+ DATA1­ DATA0+ DATA0­ CLOCK+ CLOCK­ SCL(5V) SDA(5V) HOT PLUG DET CEC +5V POWER

HDMI

15 14 12 11 9 8 6 5 3 2 80

A14 B14 A13 B13 A12 B12 A11 B11 SCL1 SDA1 HPD1

OEB 42 S1 21

LEVEL SHIFT IC5004 25 26 28 29 31 32 34 35 38 39 40 Y4 Z4 Y3 Z3 Y2 Z2 Y1 Z1 SCL SINK SDA SINK HPD SINK 1 5 3 7 1

6 4 3 ANALOG SWITCH IC5005 IC5003 HDMI+3.3V 3 +3.3V REG 1

4

1 POWER 5 CONTROL IC5002

4

1 +5.8V REG IC5006

2

+7V

STR-DG800

19

19

STR-DG800
Ver. 1.1

4-6. BLOCK DIAGRAM -- POWER SECTION --

J4086 PHONES PRE DRIVER IC600 IN 2 PRE DRIVE +VOUT2 12 -VOUT2 11 R-CH

TM2880 POWER AMP Q671-674 RELAY DRIVER Q240 RELAY DRIVER Q2880 RY2881 RELAY DRIVER Q500 R-CH R RY500 RY600 CURRENT DETECT Q475,476 R-CH R-CH OVERLOAD DETECT D475,Q477 R-CH RELAY DRIVER Q600 RY700 RELAY DRIVER Q700 L CURRENT DETECT Q525,526 R-CH R-CH OVERLOAD DETECT D525,Q527 R-CH RELAY DRIVER Q400 RY400 R-CH R TM602 TM601 R CURRENT DETECT Q725,726 OVERLOAD DETECT D725,Q727 D290 -30V -30V REG Q250 D291 R290 T901 POWER TRANSFORMER CENTER E2 MODEL S901 VOLTAGE SELECTOR 240V 220V 120V S901 -3 SURROUND BACK R-CH L R SURROUND SPEAKERS IMPEDANCE USE 8-16 L R-CH RY240 TM600 L FRONT A FRONT B R

L-CH R-CH R-CH

8

DRIVE

-B-1 +B-1

CURRENT DETECT Q675,676 R-CH R-CH

OVERLOAD DETECT D675,Q677 R-CH

PRE DRIVER IC400 IN 2 PRE DRIVE +VOUT2 12 -VOUT2 11

SL-CH

8

DRIVE

POWER AMP Q471-474

TUNER/ AUDIO SECTION (Page 15)

SR-CH

R-CH PRE DRIVER IC500 -B-1 +B-1

F
SBL-CH 6 IN1 PRE DRIVE

DRIVE

+VOUT1 2 -VOUT1 3

POWER AMP Q521-524

PRE DRIVER IC700 C-CH 6 IN1 PRE DRIVE +VOUT1 DRIVE -VOUT1 2 3

POWER AMP Q721-724

REAR RY

-B-1 +B-1 PROTECTOR 61
D1110 D1108 D1107 D1111

PROTECTOR D201-204 Q200-202,255,256 +B -B FRONT-RY REAR-RY TU+10V C/SB RY IC210 HP DETECT SB-RY +B-1 OVERLOAD 2 DETECT 7 AMP IC260 +7V INVERTER Q210 B+ SWITCH Q220,225 -7V +5V-2 +5V-1 +2.6V +3.3V 3 IC1001 +5V REG IC1901 5 +3.3V/+2.6V 4 REG 2 1 3 3 3 +7V REG -7V REG IC265 +5V REG IC1031 -30V RELAY DRIVER Q911 IC1904 +3.3V (STBY) 3 +3.3V 1 REG 1 1 +15V 3 -B-1 B- SWITCH Q221,228,235 IC1902 +9V REG 1 RECT D801,802 RELAY DRIVER Q809

HP DETECT

SR-CH

R-CH

HP-RY SB-RY FRONT RY REAR-RY C/SB RY

-B-1 +B-1

· Signal path : TUNER (FM/AM) · R-ch is omitted due to same as L-ch. · Abbreviation CND : Canadian model E2 : 120V AC area in E model TW : Taiwan model

HP_RY 62 FRONT RY 66 REAR_RY 69 C/SB RY 68 HP DETECT 55 SP_B_RY 67

HP-RY

RELAY SWITCH

-2 RY802,803 R861 RECT D865 R860 EXCEPT E2 MODEL
F901

F904 US,CND MODEL -1

2 -15V +VCC -VCC D251 F1 F2 RY911 RECT D866

AC1 R851

SYSTEM CONTROL IC1101 (5/5)

J911 AC OUTLET

AC2

R852 F902 EXCEPT TW MODEL T902 POWER TRANSFORMER
JW809

BRIDGEABLE RY 72 P0WER RY 58

RECT D921-924 AC IN DETECT Q914

EXCEPT E2 MODEL

D925

D926

STOP 48

AC IN ~

STR-DG800

20

20

STR-DG800
Ver. 1.1

4-7. CIRCUIT BOARDS LOCATION

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)

STANDBY board DC-SPEAKER A board

POWER KEY board MAIN board ADCC board

for schematic diagram: · All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. · · 2 : nonflammable resistor. · 5 : fusible resistor. · C : panel designation.
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce port