Text preview for : SONY DSC-T100 SERVICE MANUAL LEVEL 2 VER 1.1 2007.11 (9-852-191-32).pdf part of SONY DSC-T100 SONY DSC-T100
DIGITAL STILL CAMERA.
SERVICE MANUAL VERSION 1.1 2007.11
PART#(9-852-191-32)
Back to : SONY DSC-T100 SERVICE MAN | Home
DSC-T100
SERVICE MANUAL
Ver. 1.1 2007.11
Revision History How to use Acrobat Reader LEVEL
2
Internal memory ON BOARD
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Brazilian Model Japanese Model Tourist Model
Photo: Silver
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAM SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· Precaution on Replacing the SY-171 Board
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DIGITAL STILL CAMERA
DSC-T100_L2
9-852-191-31
Sony EMCS Co.
2007K0500-1 © 2007.11 Published by Kohda TEC
SPECIFICATIONS
Camera
[System]
Image device: 7.18 mm (1/2.5 type) color CCD, Primary color filter Total pixel number of camera: Approx. 8 286 000 pixels Effective pixel number of camera: Approx. 8 083 000 pixels Lens: Carl Zeiss Vario-Tessar 5 × zoom lens f = 5.8 - 29.0 mm (35 - 175mm when converted to a 35 mm still camera) F3.5 - 4.4 Exposure control: Automatic exposure, Scene Selection (9 modes) White balance: Automatic, Daylight, Cloudy, Fluorescent 1, Fluorescent 2, Fluorescent 3, Incandescent, Flash File format (DCF compliant): Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media: Internal Memory (approx. 31 MB), "Memory Stick Duo" Flash: Flash range (ISO (Recommended Exposure Index) set to Auto): approx. 0.1 to 3.7 m (4 inches to 12 feet 1 3/4 inches) (W)/ approx. 0.8 to 2.9 m (2 feet 7 1/2 inches to 9 feet 6 1/4 inches) (T)
[Input and Output connectors]
Multi connector: Video output Audio output (mono) USB communication USB communication: Hi-Speed USB (USB 2.0 compliant)
BC-CSG/BC-CSGB/BC-CSGC battery charger
Power requirements: AC 100 to 240 V, 50/60 Hz, 2 W (BC-CSG/BC-CSGC)/ 2.6 W (BCCSGB) Output voltage: DC 4.2 V, 0.25 A Operating temperature: 0 to 40°C (32 to 104°F) Storage temperature: -20 to +60°C (-4 to +140°F) Dimensions: Approx. 62 × 24 × 91mm (2 1/2 × 31/32 × 3 5/8 inches) (W/H/D) Mass: Approx. 75 g (2.7 oz)
[LCD screen]
LCD panel: 7.5 cm (3.0 type) TFT drive Total number of dots: 230 400 (960 × 240) dots
[Power, general]
Power: Rechargeable battery pack NP-BG1, 3.6 V AC-LS5K AC Adaptor (not supplied), 4.2 V Power consumption (during shooting): 1.1 W Operating temperature: 0 to 40°C (32 to 104°F) Storage temperature: -20 to +60°C (4 to +140°F) Dimensions: 91.85 × 9.2 × 22.3mm (3 5/8 × 2 3/8 × 29/32inches) (W/H/D, excluding protrusions) Mass: Approx. 172 g (6.1 oz) (including NP-BG1 battery pack and wrist strap, etc.) Microphone: Monaural Speaker: Monaural Exif Print: Compatible PRINT Image Matching III: Compatible PictBridge: Compatible
Rechargeable battery pack NPBG1
Used battery: Lithium-ion battery Maximum voltage: DC 4.2 V Nominal voltage: DC 3.6 V Capacity: 3.4 Wh (960 mAh) Design and specifications are subject to change without notice.
DSC-T100_L2 --2--
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. FLEXIBLE Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
DSC-T100_L2 --3--
TABLE OF CONTENTS
Section Title Page
1.
1-1. 1-2. 1-3. 1-4.
SERVICE NOTE
Precaution on Replacing the SY-171 Board ···················· 1-1 Self-diagnosis Function ··················································· 1-1 Process After Fixing Flash Error ····································· 1-2 Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-3 1-5. How to Write Data to Internal Memory ·························· 1-4
2. 3.
3-1. 3-2. 3-3. 3-4.
DISASSEMBLY BLOCK DIAGRAMS
Overall Block Diagram (1/2) ··········································· 3-1 Overall Block Diagram (2/2) ··········································· 3-2 Power Block Diagram (1/2) ············································· 3-3 Power Block Diagram (2/2) ············································· 3-4
2-1. Disassembly ····································································· 2-2
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-3 4-3. Printed Wiring Boards ··················································· 4-19
5.
REPAIR PARTS LIST
5-1. Exploded Views ······························································· 5-2 5-2. Electrical Parts List ························································· 5-5
DSC-T100_L2 --4--
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE SY-171 BOARD
DESTINATION DATA When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting. Refer to Service Manual ADJ, and perform "DESTINATION DATA WRITE". USB SERIAL No. The set is shipped with a unique ID (USB Serial No.) written in it. This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. Refer to Service Manual ADJ, and perform "USB SERIAL No. INPUT".
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the LCD screen what to do. Details of the self-diagnosis functions are provided in the Instruction manual.
1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
LCD screen
Blinks at 3.2 Hz
C
Repaired by:
32
Block
00
Detailed Code
Refer to "1-2-3. Self-diagnosis Code Table". C : Corrected by customer Indicates the appropriate E : Corrected by service step to be taken. engineer E.g. 13 ....Format the "Memory Stick Duo". 32 ....Turn on power again.
DSC-T100_L2 1-1
1-2-3. Self-diagnosis Code Table
Self-diagnosis Code
Repaired by:
Block Function
Detailed Code
Symptom/State
Correction
C
1
3
0
1
C E
3 6
2 1
0 0
1 0
The internal memory has experienced a format error. "Memory Stick Duo" is unformatted. "Memory Stick Duo" is broken. "Memory Stick Duo" type error The camera cannot read or write data on the "Memory Stick Duo". Trouble with hardware
Format the internal memory.
E
6
1
1
0
E E
6 6
2 2
0 1
2 0
E
6
2
1
1
E
6
2
1
2
E E E
6 9 9
2 1 2
2 0 0
0 1 0
Format the "Memory Stick Duo". Insert a new "Memory Stick Duo". Insert a supported "Memory Stick Duo". Turn the power off and on again, or taking out and inserting the "Memory Stick Duo" several times. Turn the power off and on again. Retry turn the power on by the power switch. If it does not recover, check the focus reset sensor of lens block (pin 6 of Difficult to adjust focus (Cannot initialize focus) CN402 on the SY-171 board). If it is OK, check the focus motor drive IC (IC401 on the SY-171 board). Retry turn the power on by the power switch. Check the zoom reset sensor of lens block (pin 9 of CN402 on the SY-171 Zoom operations fault board) when zooming is performed when the zoom button is (Cannot initialize zoom lens.) operated. If it is OK, check the zoom motor drive IC (IC401 on the SY-171 board). Check or replacement of the IC for steadyshot (IC503 on the SYAbnormality of IC for steadyshot. 171 board). Check or replacement of the IC for steadyshot (IC503 on the SYLens initializing failure. 171 board). Check the HALL element (PITCH) of optical image stabilizer (pin ea, es of CN402 on the SY-171 board). If it is OK, check Lens overheating (PITCH). PITCH angular velocity sensor (SE502 on the SY-171 board) peripheral circuits. Check the HALL element (YAW) of optical image stabilizer (pin ed, ef of CN402 on the SY-171 board). If it is OK, check YAW Lens overheating (YAW). angular velocity sensor (SE501 on the SY-171 board) peripheral circuits. Check the OIS temp sensor of optical image stabilizer (pin wa of Abnormality of thermistor. CN402 on the SY-171 board). Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note) Non-standard battery is used. Use the compatible battery only.
Note: After repair, be sure to perform "1-3. PROCESS AFTER FIXING FLASH ERROR".
1-3. PROCESS AFTER FIXING FLASH ERROR
When "FLASH error" (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting. The images stored in the internal memory are retained.
1 Select [Initialize] with v/V/b/B, then press z. The message "Initialize all settings" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting.
To cancel the resetting
Select [Cancel] in step 2, then press z.
· Make sure that the power is not disconnected during resetting.
DSC-T100_L2 1-2
1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-171 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-171 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a "Memory Stick Duo".
1 Insert a "Memory Stick Duo" having 32MB or larger capacity. 2 Select [Copy] with v/V/b/B on the control button, then press z. The message "All data in internal memory will be copied" appears. 3 Select [OK] with v, then press z. Copying starts.
To cancel the copying
Select [Cancel] in step 3, then press z.
· Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. · You cannot copy individual images. · The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick Duo" after copying, then execute the [Format] command in [ Internal Memory Tool]. · When you copy the data in the internal memory to the "Memory Stick Duo", all the data will be copied. You cannot choose a specific folder on the "Memory Stick Duo" as the destination for the data to be copied. · Even if you copy data, a DPOF (Print order) mark is not copied.
Method for Formatting the Internal Memory
This item does not appear when a "Memory Stick Duo" is inserted in the camera.
Format
Formats the internal memory.
· Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V/b/B on the control button, then press z. The message "All data in internal memory will be erased" appears. 2 Select [OK] with v, then press z. The format is complete.
To cancel the formatting
Select [Cancel] in step 2, then press z.
DSC-T100_L2 1-3
1-5. HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement. To change the setting, use the write enable tool "WriteEnableTool.exe".
Data writing method
1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the "Sony Seus USB Driver". 2) Start the Write Enable Tool and the SeusEX. 3) Click the [Activate Write Enable Mode] button of the Write Enable Tool.
4) Upon completion of the setting change, the following message will be displayed.
5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage). 6) Write the data read out into the PC to the internal memory of the camera. 7) Disconnect the PC from the camera, and turn off the camera. Note: By turning off the camera, the write enable setting is reset.
DSC-T100_L2 1-4E
2. DISASSEMBLY
NOTE FOR REPAIR
· Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. · When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped. · When installing a connector, don't press down at wire of connector. It is possible that a wire is snapped. · Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)
DISCHARGING OF THE ST-162 FLEXIBLE BOARD'S CHARGING CAPACITOR (C901)
The charging capacitor (C901) of the ST-162 flexible board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.
Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds. C901
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a resistor of 1 k /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
1 k/1 W
R:1 k/1 W (Part code: 1-215-869-11)
Wrap insulating tape.
DSC-T100_L2 2-1
HELP
2-1. DISASSEMBLY
2-1-1. FRONT CABINET/LENS SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
HARDWARE LIST
1 Cabinet (Front) Assy (1-1 to 1-9) 2 Lens Block (2-1 to 2-5)
Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds. C901
R:1 k/1 W (Part code: 1-215-869-11)
1-4 (#20/#21)
1-8 (#26) 2-5 1-6 (#26)
HELP
1-7 (#26) 2-1 2-2 1-2 (Claw)
2-3 1-9 (RED only) 1-3
HELP
2-4 (#26)
1-5 (#20/#21)
1-1 (#20/#21)
2 Lens Block
HELP
1 Cabinet (Front) Assy
DSC-T100_L2 2-2
2-1-2. LCD/MAIN BOARD SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
HARDWARE LIST
1 SY-171 Board (1-1 to 1-9) 2 Cabinet (Rear) Assy (2-1 to 2-2) 3 LCD Panel Block (3-1 to 3-2)
2 Cabinet (Rear) Assy 3 LCD Panel Block
3-1
3-2 1-2 1-1 2-1 (#20/#21)
1 SY-171 Board
1-9 (Claw)
1-5 (Claw)
SY -17
1-8 (Claw)
1
1-3
2-2 1-6 (Claw) 1-4 (#71) 1-7
HELP
DSC-T100_L2 2-3
2-1-3. BT HOLDER SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
HARDWARE LIST
1 SW-496 Flexible Board (1-1 to 1-5) 2 Flash Unit (2-1 to 2-4) 3 BT-035 Flexible Board (3-1 to 3-3)
1-1 (#26)
HELP
1-2
1-3 (Claw) 2-1 (Claw)
2-2
1-4
1-5 (Claw)
2-3 (Claw) 2-4 (Claw)
1 SW-496 Flexible Board
3-2
3-3
HELP
3-1 (Solder)
3 BT-035 Flexible Board
2 Flash Unit
DSC-T100_L2 2-4E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
SY-171 board
Harness (Black)
Harness (Red) Loudspeaker
Microphone block Harness (Black)
Harness (Red)
SW-496 flexible board
DSC-T100_L2
HELP
PRECAUTIONS WHEN HOLDING THE LSV-1220A
· Hold the LSV-1220A at the center of both sides. · Do not hold the LSV-1220A in the front-rear thickness direction.
LSV-1220A Hold here.
LSV-1220A
· Do not touch the top of lens prism.
· Do not touch the motor coil or terminals.
LSV-1220A
LSV-1220A Motor
Do not touch here. Lens prism Do not touch the coil. Do not touch the terminals.
DSC-T100_L2
HELP
FOCUS MOTOR DISASSEMBLING PROCEDURE
Solder
Lens block Lens Note: Take care not to melt the mold part of .
Cover the lens surface for protection. Focus motor Screw
1 Cover the lens surface to protect from solder splashing. 2 Remove the solder. 3 Remove one screw. * Tightening torque = 0.5 ± 0.1kgf · cm 4 Remove the focus motor from the lens block.
ZOOM MOTOR DISASSEMBLING PROCEDURE
Lens block Lens
Cover the lens surface for protection.
Solder Note: Take care not to melt the mold part of .
Screw
Zoom motor
1 Cover the lens surface to protect from solder splashing. 2 Remove the solder. 3 Remove two screws. * Tightening torque = 0.5 ± 0.1kgf · cm 4 Remove the zoom motor from the lens block.
DSC-T100_L2
HELP
INSTALLATION METHOD OF BATTERY TERMINAL BOARD
1 Install the BT-035 flexible board in the BT holder. 2 Insert the battery terminal board into a slit in the BT holder to install. * The battery terminal board is attached with the notch for installation.
BT holder
1BT-035 flexible board
Notch
Battery terminal board 2Battery terminal board
3 Fold the notch 3 or 4 times repeatedly to break.
Battery terminal board Notch Notch
DSC-T100_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (2/2)
DSC-T100_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS BLOCK
LENS IRIS (METER) 18 IC001 8.1M CCD IMAGER M901 ZOOM MOTOR M902 FOCUS MOTOR 10 IC002 BUFFER 14 38
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-171 BOARD (1/2)
AB21, AC21, AB20, AC20, AB19, AC19, AC18, AE21, AF21, AE20, AF20, AE19, AF19, AE18 N5, P4, M4, N2, L3, L1, P5, L5, N4, N3, M2, L2, K4, K3 D17, B19, E17, A19, B18, D18, B17 E16, A18, D16, A17
CN713 (1/2)
CD-696 FLEXIBLE BOARD
SW-496 FLEXIBLE BOARD (1/2)
CN001
46 - 39
D14
CA_AD00 - CA_AD13
LCD_D0 - LCD_D7
D0 - D7
1, 16
18
POWER_SAVE
6 - 13
CN301 CCD_OUT
C7
LCD901
37, 35, 34
4-2
IRIS MOTOR
H1 - H3 LH1 RG V1, V2, V3A, V3B, V4, V5A, V5B, V6 - V10
H3, H1 J2, H4 F1, G2, E2, E1, G1, D4, D3, F4, E4, F3, D1, C2
2
21 - 32
3 - 14
13, 14 34, 33
32, 33 16, 15
ZOOM RESET SENSOR
FOCUS RESET SENSOR
IC202 1 CLOCK 3 GENERATOR 5 (4/11)
32, 33
GEAR_ON GEN_SYS_CLK
Y13 Y12
CPU (4/11, 5/11)
IC_211_2_SO, XIC_211_2_SCK
SI, SCK
18, 17
M
M
M
27 20
6 8
IC304 K13 CCD SIGNAL J13 PROCESS, K14 TIMING GENERATOR P7 (1/11) P8
P10, P9, P11
28 - 30
CA_HD CA_FD GEN_TG_CLK X201 36MHz
AE23 AF22 AF18 IC211 (1/2)
LCD_CK, LCD_HD, LCD_VD XCS_ PANEL XDD_SYS_RST
DCK, HD, VD XCS RESET
14 - 16
U19
31 30
19 20
3.0 inch COLOR LCD UNIT
D901 BACKLIGHT BL_H 1 2
VST1, VST2 VHLD1, VHLD2 LV SUB SUB_CONT Q302
2
D10 XDD_SYS_RST
BL_L
XCS_FE, XIC_211_3_SCK, IC_211_3_SO VSUB_CONT_PRE, VSUB_CONT_POST
V19, D19, C25
D7 - D9
31 1 25
12 19 17
G4 J4
OVERALL (2/2) (PAGE 3-2)
51
BL_L
C6
E18, B23
Q301 IC401 LENS DRIVE D4 (2/11)
R7, AF25
V8 AF8
XCS_AUDIO IC_211_AUIN
D6 A6 A3 2 MIC_SIG MIC901
XLENS_DRIVER_PS
H11
E6, D5
IC_211_2_SO, XIC_211_2_SCK
A1, C1
W16, AD25, Y18, Y17
F5, E5, D3, F1
CN402 IRIS_A, A, B, B
F2, E2, D2, B1
AE8
IC_211_AUOUT
B6
IC602 AUDIO/VIDEO AMP (7/11)
SP±
17 - 14
IRIS MOTOR DRIVER
IRIS_DIR_A, IRIS_BRK_A, IRIS_DIR_B, IRIS_BRK_B
SP901 SPEAKER
FP-636 FLEXIBLE BOARD (1/2)
CN710 (MAGIC FLEXIBLE) E2 AU_LINE_OUT V_LINE_OUT 39 40 AOUT_L V_OUT 9 7
MC-178 BOARD (1/2)
W001 (1/2) 16 20
D5, A6, B6, C5
D6, E6, B7, C6
1-4
FOCUS_A, A, B, B
FOCUS MOTOR DRIVER
FC_DIR_A, FC_DIR_B, FC_BRK_A
W18, AB26, W17
F3 ZOOM_A, A, B, B ZOOM MOTOR DRIVER ZM_DIR_A, ZM_DIR_B, ZM_BRK_A
F1
AB23, AC26, AA23
B4, B5, B3, A3
A2, C3, C4, A1
36 - 39
Q242 - Q244 IC_211_CVOUT AB13 VOUT_1 AF12 VOUT_2 AC12 XHD_EN
Q241 IC_211_YOUT IC_211_PBOUT IC_211_PROUT 26 25 24 HDY HDPb HDPr 20 22 24 24 4 2 CN001 (1/2) MULTI CONNECTOR
FC_SENS FC_SENS_GND ZM_SENS ZM_SENS_GND LENS TEMP SENSOR LENS_TEMP
6 8 9 11 12
FC_SENS XFC_RST_LED ZM_SENS_1ST XZM_RST_LED LENS_TEMP
Y10 M8 AD26 J8 AE3
BUFFER
CLAMP
V7
29, 32
17, 14
USB_DP, USB_DM
D±
OPTICAL IMAGE STABILIZER
OIS TEMP SENSOR
OIS_TEMP
21
TZ_HALL_TEMP
AF3
3
OVERALL (2/2) (PAGE 3-2)
A13 - A15, B13 - B15
MSX_BS, MSX_D0 - MSX_D3, MSX_CLK
USB_VBUS
35
USB_VBUS
11
22, 23, 33, 34 18, 19, 26, 27
SE501
YAW MOTOR
B10, D10
M
YAW±
J5
SWAOUT
13 IC506
21
YAW SENSOR
XMS_IN
CN704 6 MEMORY STICK DUO
D5, D6
24, 25
HALL ELEMENT
YAW_HALL_BIAS±, YAW_HALL±
G6, J8, J9, J7
CLK, DATA
PITCH/YAW SENSOR AMP (3/11) SE502 1 PITCH SENSOR
29 - 32 20, 24, 25
PITCH MOTOR
M
PITCH± PITCH_HALL_BIAS±, PITCH_HALL±
J3, J2, H2, J4 B1, D1
IC503 OPTICAL IMAGE STABILIZATION DRIVE (3/11) G5
SWBOUT
10
HALL ELEMENT
C9 A7 A3 A6 A5
CA_FD XDD_SYS_RST CLK_IC_503 XIC_211_IC_503_RST XCS_IC_503 XDD_SYS_RST
W13 H10 U8
A4, B4, B5
1
OVERALL (2/2) (PAGE 3-2)
2 - 5, 7, 8
IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
05
DSC-T100_L2 3-1
10, 12
6
Y1, AA1
3-2. OVERALL BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-171 BOARD (2/2) FP-636 FLEXIBLE BOARD (2/2)
CN710 (MAGIC FLEXIBLE)
MC-178 BOARD (2/2)
SW-496 FLEXIBLE BOARD (2/2)
S002 POWER S003 N 8
XPWR_ON CN713 (2/2) XPWR_ON
10
XPOWER_ON
W001 (2/2) 37
XPOWER_ON
7
19 - 22
25 - 28
XPWR_ON
B8
H8
BATT_SENS ST_UNREG BATT_SENS CAM_13V CAM_-7.5V PANEL_6.4V TI_DD_5V MT_5.0V D_3.0V A_3.0V DDR_1.8V D_1.8V D_1.2V MS_VCC BL_H D002
ACV_UNREG
ACV_UNREG
7
DIRECT_PB
DIRECT_PB
B7
Q004, Q013
13
XACV_DET
34
BATT_XEXT
19
14 - 18
29 - 33
CHARGE_V
CHARGE_V
S001 (SHUTTER) S004 - S012
14 13
XAE_LOCK_SW XSHUT_SW
IC103 LENS BARRIER 2 DETECT (8/11) Q102 BATT_SENS BATTERY DETECT A8
FUNCTION KEY
12, 11
KEY_AD_1, KEY_AD_2
IC001 DC/DC CONVERTER (9/11)
17, 21
23, 25
D003 (POWER)
4
XPWR_LED Q101 IC101 C6 D8 FRONT CONTROL (8/11) F9
CN001 (2/2) MULTI CONNECTOR
3
OVERALL (1/2) (PAGE 3-1)
XMS_IN USB_VBUS
Q006 BL_EN2 BACKLIGHT CONTROL BL_L
2
OVERALL (1/2) (PAGE 3-1)
X101 32.768kHz
J5 B9 J4 A1 B4
XPWR_OFF XIC_211_RST_REQ XDD_SYS_RST XCS_FR
G8 W12 AB18 A23
K8 G9
XACV_IN XAV_JACK_IN (XACC_IN) IC_211_1_UI, IC_211_1_UO
D003 36 JACK_IN UART_Rx, UART_Tx 12 XAV_JACK_IN UART_Rx, UART_Tx 26
D26, G19
11, 12
35, 36
ST-162 FLEXIBLE BOARD
BT001 LITHIUM BATTERY 1 2 ST_UNREG 4
CN701
VL_3V D101
D1, D2, E1
XE_H + FLASH UNIT TRIGGER TRIGGER_GND
D001 4 3
T001
BACK UP VCC (8/11)
IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK
IC106 RESET (8/11) 1 D102
C901 CHARGING CAPACITOR XE_L Q001 FLASH DRIVE
15
7
10 9 FLASH CONTROL, 6 CHARGE CONTROL 4 IC002
14 13 12 11
1, 2
STRB_CHG XSTRB_FULL STB_CHG_CONT STRB_ON1
1
OVERALL (1/2) (PAGE 3-1)
XDD_SYS_RST IC211 (2/2) IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK CPU (4/11, 5/11)
Q704 D002 SELF-TIMER/ AF ILLUMINATOR 1 XAF_LED AF LED CONTROL
D706 (MS ACCESS) AFLED_CONT
H8
G15
AC8, AF6
XPWR_LED XAE_LOCK_SW XSHUT_SW KEY_AD_1, KEY_AD_2 STRB_CHG XSTRB_FULL STB_CHG_CONT STRB_ON1
Y9 N19 R19 XCS_IC_201, XIC_211_1_SCK, IC_211_1_SO, IC_211_1_SI
H17, A24, G17
3 2
IC102
5 4
D7 A9
E2
W20, H18, B24, G18
V2 H9 H15 Y16
B1, B5, C5, D5
CN702
BT-035 FLEXIBLE BOARD
1-5
BATT_UNREG BATT_SIG BATT_GND
15, 9
IC201 BATTERY E4 AUTHENTICATION (11/11)
+
S
6
XDD_SYS_RST
B2
05
DSC-T100_L2 3-2
7 - 10
BT901 BATTERY TERMINAL
3-3. POWER BLOCK DIAGRAM (1/2)
MC-178 BOARD
W001
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-636 FLEXIBLE BOARD
CN710 (MAGIC FLEXIBLE)
SY-171 BOARD (1/2)
F001 Q001 B+ SWITCH MS_VCC CN704 MEMORY STICK DUO
23, 25
25-28
ACV_UNREG
19-22
ACV_UNREG Q004, 013 XACV_DET D003 D002
F002
IC001 DC/DC CONVERTER (9/11) 28 GD 45 BATT L009 13 PVSD LXSD 16 ONSD 15 DDC1P2_EN
9
19 CN001 MULTI CONNECTOR
BATT_XEXT
MS_PWR_ON
F
POWER (2/2) (PAGE 3-4) ST_UNREG D_1.2V
34
13
17, 21
29-33
14-18
CHARGE_V
CHARGE_V
29 PVBST 7 XPOWER_ON 37 10 XPOWER_ON
LXBST 31 SWBST 30 ONBST 22 LXINV 21 PVINV 20 ONINV 1
D007 L004
CAM_13V
D010 CAMDD_EN
CAM_-7.5V
BT901 BATTERY TERMINAL
BT-035 FLEXIBLE BOARD
CN702
XACV_IN IC201 BATTERY AUTHENTICATION (11/11) E4 TXRX P144_SOA0 P143_SIA0 P142_XSCKA0 P120_INTP0 D5 C5 B5 B1 IC_211_1_SI IC_211_1_SO XIC_211_1_SCK XCS_IC_201 D_3.0V B2 XRESET IC106 RESET (8/11) L007 47 LXSU
L001
+
S
1-5
BATT_UNREG
E
POWER (2/2) (PAGE 3-4) 35 PVLED
BATT_SIG BATT_GND
PVM 4 LXM 5 ONM 3 LXLED SWLED FBLLED ONLED 33 34 37 36 D011 SU 43 PVSU 44 ONSU 46 SEQCCD 27 9 PVAFE LXAFE 8 ONAFE 10
L005 DDC2P9_EN D006 L003 BL_EN1 BL_EN2 Q003 B+ SWITCH VSU_EN DDC5PSW_EN Q006 BACKLIGHT CONTROL
A_3.0V D_3.0V
6
BL_H BL_L
7-10
MT_5.0V
A
POWER (2/2) (PAGE 3-4)
XDD_SYS_RST
D102 1 OUT Vdd 4
IC101 FRONT CONTROL (8/11) BATT_SENS H8 DDC2P9_AD H7 DDC1P8_AD J7 D_3.0V D_1.8V BACK_UP_VCC
L006 DDC1P8_EN
G
POWER (2/2) (PAGE 3-4) Q014 B+ SWITCH DDCPV_EN IC006 D008, D009, C023, C025 CHARGE PUMP CIRCUIT 6.4V REG (9/11) 6 Vin Vout 4 Vcont 1 PANEL_6.4V
A9 CS B4 XSYS_RST
IC002 DDC1P2_EN D9 CAMDD_EN B2 DDC2P9_EN E9 BL_EN1 BL_EN2 DDC5PSW_EN VSU_EN DDC1P8_EN DDC1P8_LVDET PANEL_EN EVER_PSB SW1P8_EN LDO1P8_EN DISW1P8_EN DISW2P9_EN F8 F9 F7 J8 E8 C9 B1 J9 J1 H2 C2 C1 DDC1P2_EN CAMDD_EN DDC2P9_EN BL_EN1 BL_EN2 DDC5PSW_EN VSU_EN DDC1P8_EN DDCPV_EN PANEL_EN EVER_PSB SW_1P8_EN LDO_1P8_EN DISW1P8_EN DISW2P9_EN L002 9 6 7 1 SW VBAT LBI EN
5V REG (9/11) PANEL_EN VOUT 2 EVER_PSB D_3.0V D_1.8V SW_1P8_EN IC003 1.8V REG (9/11) B2 VIN VOUT B1 STBY A2 LDO_1P8_EN DISW1P8_EN DISW2P9_EN Q010, 012 B+ SWITCH
TI_DD_5V
PS 8
D_1.8V Q007 1.8V/3.0V DISCHARGE DDR_1.8V
B
POWER (2/2) (PAGE 3-4)
XIC_211_RST_REQ XPWR_OFF
A1 XRESET_REQ B9 XPOWER_OFF
C
POWER (2/2) (PAGE 3-4)
XPWR_ON DIRECT_PB
BACK_UP_VCC
B8 XPOWER_ON0 B7 XPOWER_ON2 A8 XPOWER_ON1
VL_3V IC102 BACK UP VCC (8/11) XRSTX D7 DDC1P2_RESET C8 1.2V_INT D101 2 VCH 3 VBAT VOUT 6 7 VIN VRO 8 5 XRESET 4 CS BATTERY DETECT EVER_3V IC007 VOLTAGE DETECTOR (9/11) 1 VOUT VIN 4 VSEN 3 IC103 LENS BARRIER DETECT (8/11) 2 OUT
D
POWER (2/2) (PAGE 3-4)
DDC2P9_EN
Q102
05
DSC-T100_L2 3-3
3-4. POWER BLOCK DIAGRAM (2/2)
SY-171 BOARD (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SW-496 FLEXIBLE BOARD
CN713 D_1.8V PANEL_6.4V D_3.0V XDD_SYS_RST L702 VCCI VCC2(6V) VCC(3V) RESET
IC501
23, 24 25, 26 27, 28
2.8V REG (3/11) A_3.0V B2 VIN VOUT B1 VCONT A2
IC506 PITCH/YAW SENSOR AMP (3/11) SE502 PITCH SENSOR IC503 OPTICAL IMAGE STABILIZATION DRIVE (3/11) SE501 YAW SENSOR
L701
CN001 VCCI VCC2(6V) VCC(3V) RESET
36 LCD901 37 38 20 3.0 inch COLOR LCD UNIT
IC502 1.5V REG (3/11)
D_1.8V
B2 VIN VOUT B1
30
D_3.0V MT_5.0V
BL_H BL_L
BL_H BL_L
50 51 D003 (POWER) S002 8 POWER S003 7
BL_H BL_L
1 2 D901 BACKLIGHT
A
ST_UNREG D_1.2V CAM_13V CAM_-7.5V POWER (1/2) (PAGE 3-3)
XDD_SYS_RST XIC_211_IC_503_RST
A7 RESET_N A6 XDL
D_3.0V
5
XDD_SYS_RST
C
POWER (1/2) (PAGE 3-3)
XPWR_ON
DIRECT_PB
A_3.0V D_3.0V
G
POWER (1/2) (PAGE 3-3)
BL_H BL_L MT_5.0V
D_1.8V D_3.0V TI_DD_5V MT_5.0V
D_1.8V D_3.0V TI_DD_5V MT_5.0V TI_DD_5V AU_AVCC MT_5.0V L601 IC602 AUDIO/VIDEO AMP (7/11) D601 H10 GPE_09 AB18 XRESET L602 D602
CN701
ST-162 FLEXIBLE BOARD
8, 9
L001
T001 D001 FLASH UNIT
ST_UNREG
ST_UNREG M_5V Q710 AF LED DRIVE M_5V
10
2
PANEL_6.4V TI_DD_5V
D002 SELF TIMER/ AF ILLUMINATOR IC002
Q704 VL_3V
AF LED CONTROL
XAF_LED
1 FLASH CONTROL, CHARGE CONTROL
VL_3V
A_3.0V D_1.8V DDR_1.8V VL_3V D_3.0V R254 D_1.2V DDR_1.8V D_1.8V FB281 IC211 CPU (4/11) (5/11) (6/11) L211 CAM_3.5V IC307 TI_DD_5V 3.5V REG (1/11) CAM_3.5V FB302 D_3.0V D_1.8V IC202 CLOCK GENERATOR (4/11) CAM_13V R253 FB290 L241 TPU2_OUT G15 AFLED_CONT
4
BT001 LITHIUM BATTERY
D706 (MS ACCESS)
IC305 13V REG (1/11) L303 5 Vin Vout 4 L302 CN301 CAM_13V 15
CD-696 FLEXIBLE BOARD
IC001 8.1M CCD IMAGER
CAM_-7.5V
CAM_-7.5V
16
FB201 FB282 FB283
Q303 -7.5V DISCHARGE
IC002 BUFFER
D B
POWER (1/2) (PAGE 3-3) XACV_IN XIC_211_RST_REQ XPWR_OFF W12 XRESET_REQ G8 GPE_00 POWER (1/2) (PAGE 3-3)
B2 VIN VOUT B1 STBY A2
DDC2P9_EN D_3.0V IC306 2.3V REG (1/11) B2 VIN VOUT B1 FB301 FB303 IC304 CCD SIGNAL PROCESS, TIMING GENERATOR (1/11) LENS BLOCK CN402 ZM_SENS_VCC ZOOM RESET SENSOR
K8 GPE_05 G18 B24 H18 W20 SIO1_RXD SIO1_TXD SIO1_SCK GPS_04
E
POWER (1/2) (PAGE 3-3)
IC_211_1_SI IC_211_1_SO XIC_211_1_SCK XCS_IC_201
6 Vin
Vout 4 Q304 2.8V/3.5V DISCHARGE 10
IC308
F
POWER (1/2) (PAGE 3-3)
MS_PWR_ON
T7 GPE_15 XDD_SYS_RST
2.8V REG (1/11)
FC_SENS_VCC D10 RESET IC401 LENS DRIVE (2/11)
7
FOCUS RESET SENSOR
D_3.0V MT_5.0V
05
DSC-T100_L2 3-4E
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
LCD901
38 39
2
CN001
3.0 inch COLOR LCD UNIT
1
D901 BACKLIGHT
SW-496 FLEXIBLE BOARD
MIC901 MICROPHONE BLOCK
FLASH UNIT
LEVEL3 SY-171 BOARD (SIDE B)
51
1
LEVEL3 SY-171 BOARD (SIDE A)
14
CN701
14
ST-162 FLEXIBLE BOARD
1
51
BT-035 FLEXIBLE BOARD
12
CN713
1 2
50
1 1
CN704 MEMORY STICK CONNECTOR
IC211 (Not supplied)
10
CN702
BT901 BATTERY TERMINAL
10
10
2
CN402
1
38
39
1
1
39 38 39
C901 CHARGING CAPACITOR
9 1-6 7 8
39 40 41-46 38 2
CN301
11
BT001 LITHIUM BATTERY
1
26
2 1 27
SP901 SPEAKER
25 28
38 41-46 40 39
W001
8 7 1-6 9
1
LENS BLOCK
LEVEL3 MC-178 BOARD (SIDE A)
CN001 MULTI CONNECTOR
IC001 (Not supplied)
LEVEL3 MC-178 BOARD (SIDE B)
LEVEL3 FP-636 FLEXIBLE BOARD
CN710 (MAGIC FLEXIBLE)
IC002 (Not supplied)
LEVEL3 CD-696 FLEXIBLE BOARD
DSC-T100_L2 4-1
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
SW-496 FLEXIBLE BOARD (LCD, CONTROL SWITCH) ST-162 FLEXIBLE BOARD (FLASH DRIVE) BT-035 FLEXIBLE BOARD (BATTERY IN)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-T100_L2
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor External dimensions (mm) Case size · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B Line · J : IN/OUT direction of (+,) B LINE. · C: adjustment for repair. · A: not use circuit (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.) Precautions for Replacement of Imager · If the imager has been replaced, carry out all the adjustments for the camera section. · As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. 1. Connection
Pattern box
Color bar chart Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = 24 cm (PTB-450) L = 11 cm (PTB-1450) Pattern box L Front of the lens Camera
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
Cyan Green
White Magenta
A B
A=B
Fig. a (Video output terminal output waveform) Electronic beam scanning frame CRT picture frame
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
DSC-T100_L2 4-3
Red Blue
B A
Schematic diagrams of the CD-696 flexible, SY-171, MC-178 and FP-636 flexible boards are not shown. Pages from 4-5 to 4-16 are not shown.
DSC-T100_L2
1
2
3
4
5
6
7
8
9
10
11
A
SW-496 FLEXIBLE BOARD
LCD, CONTROL SWITCH
XX MARK:NO MOUNT
LND051 LND050 BL_L 51 BL_H 50 N.C. 49 GND 48 GND 47 D0 46 D1 45 D2 44 D3 43 D4 42 D5 41 D6 40 D7 39 GND 38 DCK 37 GND 36 HD 35 VD 34 SCK 33 SI 32 XCS 31 RESET 30 OUT61LV 29 VCCI 28 VCCI 27 VCC2(6V) 26 VCC2(6V) 25 VCC(3V) 24 VCC(3V) 23 GND 22 GND 21 OUT18V 20 GND 19 GND 18 GND 17 GND 16 GND 15 AE_LOCK_SW 14 XSHTTER_SW 13 KEY_AD01 12 KEY_AD02 11 REG_GND 10 N.C. 9 XPWR_ON1 8 DIRECT_PB 7 N.C. 6 D_3.0V 5 XPWR_LED 4 REG_GND 3 MIC_SIG 2 MIC_GND 1
Note: All mounted parts except MIC901 are not supplied, though they are included in SW-496 flexible board. However MIC901 is not included in it.
D901 BACKLIGHT CN001 1 2 3 4 5 6 7 8 9 10 11 12 13 CL005 14 15 16 17 18 19 20 C006 1u C001 4.7u C003 1u 21 22 C011 4.7u 23 24 C007 0.1u R008 270 25 26 C008 0.1u 27 28 29 C005 1u 30 31 R009 C002 1u C010 0.047u 270 32 33 34 35 36 37 38 S001 (SHUTTER) 3 2 NO 1 S004 4 (FLASH) R001 2200 S005 (MACRO) R002 2200 S006 (DISP) S007 (SELF-TIMER) R003 2200 R004 2200 S008 (SET) 39 BL_H BL_L N.C. COM GND D0 D1 D2 D3 D4 D5 D6 D7 DCK HD VD SCK SI XCS RESET OUT5.3V COMDC VBRT COMAC OUT71V C71CFP C71CFN C3LCFP C3LCFN OUT3LV C61LCFN OUT61LV C61LCFP OUT58V OUT18V VCCI VCC2(6V) VCC(3V) GND LCD901 3.0 inch COLOR LCD UNIT 39P
B
LND049 LND048 LND047 LND046 LND045 LND044 LND043 LND042 LND041
C
LND040 LND039 LND038 LND037 LND036 LND035 LND034 LND033
D
SY-171 (10/11)
CN713 Page 4-15 of Level 3
LND032 LND031 LND030 LND029 LND028 LND027 LND026 LND025
E
LND024 LND023 LND022 LND021 LND020 LND019 LND018
F
LND017 LND016 LND015 LND014 LND013 LND012 LND011 LND010 LND009
G
LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
S002 POWER
2 4
1 3 S009 T (ZOOM) (+) R005 2200 S010 W (-/INDEX) R006 2200 S012 HOME R007 2200 S011 MENU
D003 SML-412MWT86 POWER
S003
2 4
1 3
H
CL001 MIC901 MICROPHONE BLOCK CL002 05 1 3 2 D001 XX 1 3 2 D002 XX STATIC_GND LND058
DSC-T100_L2 4-17
SW-496
· Refer to page 4-3 for mark 0.
1
2
3
4
5
6
7
8
9
10
11
A
ST-162 FLEXIBLE BOARD
FLASH DRIVE
XX MARK:NO MOUNT NO MARK:REC/PB MODE
T001 1 C007 220p R005 4700 2 D003 RB520S-40TE61 3 4
Note: BT001 (lithium battery), C901 (charging capacitor) and flash unit are not included in ST-162 flexible complete board.
D001 MA2YF8000LS0 R003 1M 1/10W ±5%
B
L001 2.2uH
LND023 CHARGE+ C002 22u CHARGELND022 C901 65u 315V CHARGING CAPACITOR LND018 TRIGGER 17 16 15 14 13 C006 0.047u LND019 TRIGGER_GND LND020 XE_H
C
HGND N.C
4.1
VBATT
N.C
LND014 LND013 LND012
STRB_CHARGE 14
XSTRB_FULL 13 I_PEAK 12
SW SW VCC F_ON
PGND
12
4.1
1
N.C
FLASH UNIT
LND021 XE_L 0 3.1 R004 XX 4 3 2 1 Q001 TIG022TS-S-TL-E FLASH DRIVE 8 7 6 5 0 272
D
SY-171 (10/11)
CN701 Page 4-15 of Level 3
LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004
PGND CHG XFULL
STRB_ON 11 5 M_5V 10 ST_UNREG 9 ST_UNREG 8 REG_GND 7 REG_GND 6 0
FLASH CONTROL, CHARGE CONTROL IC002 TPS65552RGTR
4
G_IGBT
I_PEAK
N.C
REG_GND 5 VL_3V 4 REG_GND 3 M_5V 2 XAF_LED 1 4 5 6 3 2 1 C003 XX C001 1u BT001 LITHIUM BATTERY
E
LND003 LND002 LND001
5
6
7
8
N.C
9
10
3
11
IC002
2
R001 100 1/16W ±5%
0
0
C004 XX
F
05
D002 DOR5352 SELF-TIMER/ AF ILLUMINATOR
R002 1M 1/16W ±5%
1
2
3
4
5
6
A
BT-035 FLEXIBLE BOARD
BATTERY IN
Note: BT901 is not included in BT-035 flexible board.
LND011
B
SY-171 (11/11)
CN702 Page 4-16 of Level 3
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009
BATT_UNREG 1 BATT_UNREG 2 BATT_UNREG 3 BATT_UNREG 4 BATT_UNREG 5 BATT_SIG 6 BATT_GND 7 BATT_GND 8 BATT_GND 9 BATT_GND 10
BATT_UNREG
S
LND012 BATT_SIG
BT901 BATTERY TERMINAL
LND013 BATT_GND
C
05
LND010
DSC-T100_L2 4-18
ST-162, BT-035
4-3. PRINTED WIRING BOARDS
Link
SW-496 FLEXIBLE BOARD ST-162 FLEXIBLE BOARD BT-035 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
DSC-T100_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
· · : Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers' patterns are not indicated) Through hole is omitted. Circled numbers refer to waveforms. There are a few cases that the part printed on diagram isn't mounted in this model. C: panel designation · Chip parts. Transistor
C 6 5 4 4 5 6 5 4 4 5
Diode
3 3 3 1 23
B
E
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 2
2 4
1 2 3 3
1 2
1 6 54
· · · ·
4 6 5 4 4 5 6
5 4 3 3 4 5 4
1
1 3
2 2
2
1 1 2 3 3 2 1
4
1
DSC-T100_L2 4-19
Printed wiring boards of the CD-696 flexible, SY-171, MC-178 and FP-636 flexible boards are not shown. Pages 4-21 and 4-22 are not shown.
DSC-T100_L2
SW-496 (2 layers), ST-162 (2 layers), BT-035 (1 layer)
: Uses unleaded solder.
SW-496 FLEXIBLE BOARD
Note: All mounted parts except MIC901 are not supplied, though they are included in SW-496 flexible board. However MIC901 is not included in it.
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 LND030 LND031 LND032 LND033 LND034 LND035 LND036 LND037 LND038 LND039 LND040 LND041 LND042 LND043 LND044 LND045 LND046 LND047 LND048 LND049 LND050 LND051
FLASH UNIT
1 51
ST-162 FLEXIBLE BOARD
>PI<
LND020 K
XE_H
XE_L
TRIGGER
TRIGGER_GND
C004
R004
D001
4
A
12 13
9 8 17
D003
R005
C007
IC002
1 4
R001
1 8
LND021
16
3
R002 C003
5
4
14
LND014 LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
C001
T001
L001
LND018 LND019
Q001
5
R003
C002
2 1
C006
LND023
C005
C002
R009 C010 C008 C007
3
4 2 3
D002 MIC901 D001
1 2 3 2 CL002 CL001 1
ST162
1
1
C901 CHARGING CAPACITOR
LND022
S001
R008
C003
(SHUTTER)
C011
K
6 4 LND058
1-873-401- 11
D003
A
S002
K
S003
W (-/INDEX) POWER N
S010
(ZOOM)
T (+)
S009
1
3
D002 SELF-TIMER/ AF ILLUMINATOR
R005
Note: BT001 (lithium battery), C901 (charging capacitor) and flash unit are not included in ST-162 flexible complete board.
1 05 2
BT001
CN001
CL005
BT001 BATTERY, LITHIUM SECONDARY
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
38
R001 C001 S006
MENU
S011 C006
39
v (DISP)
S005
S008
S004
BT-035 FLEXIBLE BOARD
LND011
BT901
S007
LND012
BT-035
b (MACRO)
z (SET)
B (FLASH)
Note: BT901 is not included in BT-035 flexible board.
R006
HOME
S012
R003
R004
R002
>PI<
V (SELF-TIMER)
1
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010
LND013
10 05
R007 05
1-873-402- 11
DSC-T100_L2
1-873-403- 11
4-23
SW-496, ST-162, BT-035
Mounted parts location of the SY-171 and MC-178 boards are not shown. Pages 4-25 and 4-26 are not shown.
DSC-T100_L2 4-26
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
A
B
C
FRONT CABINET/LENS SECTION
LCD/MAIN BOARD SECTION
BT HOLDER SECTION
Link
BT-035 FLEXIBLE BOARD
ELECTRICAL PARTS LIST
C
ACCESSORIES
ST-162 FLEXIBLE BOARD
C
SW-496 FLEXIBLE BOARD C
DSC-T100_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... · Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
· Color Indication of Appearance Parts Example: (SILVER) : Cabinet's Color (Silver) : Parts Color
DSC-T100_L2 5-1
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. FRONT CABINET/LENS SECTION
ns: not supplied
DISASSEMBLY
HARDWARE LIST
#20 (SILVER, RED) #21 (BLACK)
#26 LCD/MAIN Board Section (See page 5-3)
3
#26
4 (Note 1)
#26 ns
6
2 1 9
RED
10
RED
M901
#30 #30 M902 #26
#20 (SILVER, RED) #21 (BLACK) #20 (SILVER, RED) #21 (BLACK)
8
#30
10
RED
(including CD-696 flexible complete board and IC001 (CCD imager)) (Note 2)
Note 1: Be sure to read "Precautions when holding the LSV1220A" on HELP when changing the LSV-1220A. Note 2: Be sure to read "Precautions for Replacement of Imager" on page 4-3 when changing the imager.
Ref. No. 1 1 1 2 2 2 * 3 4 * 6 8
Part No. X-2177-127-1 X-2177-128-1 X-2177-148-1 X-2177-123-1 X-2177-124-1 X-2177-125-1 3-099-395-01 A-1236-991-A 3-099-396-01 A-1212-554-A
Description CABINET (FRONT) (BK) ASSY (BLACK) CABINET (FRONT) (RD) ASSY (RED) CABINET (FRONT) ASSY (SILVER) CABINET (BELT) ASSY (SILVER) CABINET (BELT) (BK) ASSY (BLACK) CABINET (BELT) (RD) ASSY (RED) SHEET (A), SY INSULATING LSV-1220A (SERVICE) (Note 1) CUSHION, LENS CCD BLOCK ASSY (including CD-696 flexible complete board and IC001 (CCD imager)) (Note 2)
Ref. No. * 9 * 10 M901 M902 #20 #21 #26 #30
Part No. 3-198-291-01 3-211-628-01 1-787-538-11 1-787-539-11 2-635-591-31
Description SHEET, BAND LIGHT INTERCEPTION (RED) SHEET, CCD LIGHT INTERCEPTION (RED) STEPPING MOTOR, OPTICAL (Z1220) STEPPING MOTOR, OPTICAL (F1220) SCREW (M1.4), NEW TRUSTAR P2 (Silver)
2-662-396-21 SCREW (M1.4), NEW, TRUSTAR, P2 (Black) 2-635-591-11 SCREW (M1.4), NEW TRUSTAR P2 (Silver) 3-086-156-11 SCREW B1.2 (White)
DSC-T100_L2 5-2
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-2. LCD/MAIN BOARD SECTION
HARDWARE LIST
54 55 53
BT Holder Section (See page 5-4) #20 (SILVER, RED) #21 (BLACK)
52
(including CN710 (FP-636 flexible board) and MC-178 complete board)
LCD901
SY -17 1
D901
51 57
56
SP901
#71
58
Ref. No. * 51 52
Part No.
Description
Ref. No. * 57 * 58 D901 LCD901 SP901 #20 #21 #71
Part No.
Description
53 54 54 55 55 55 56
3-099-398-01 PLATE, MC FIXED A-1257-764-A SY-171 BOARD, COMPLETE (SERVICE) (including CN710 (FP-636 flexible board) and MC-178 complete board) 3-099-399-01 WINDOW, LCD 3-099-401-01 BUTTON, FUNCTION (SILVER, RED) 3-099-401-11 BUTTON, FUNCTION (BLACK) X-2177-157-1 X-2177-158-1 X-2177-159-1 3-099-397-01 CABINET (REAR) ASSY (SILVER) CABINET (REAR) (BK) ASSY (BLACK) CABINET (REAR) (RD) ASSY (RED) SCREW, TRIPOD
3-198-292-01 CUSHION, MC 3-196-553-01 1-480-023-11 A-1257-852-A 1-826-403-31 2-635-591-31 GASKET (SP) BLOCK, LIGHT GUIDE PLATE (3.0) SERVICE, LCD BLOCK ASSY LOUDSPEAKER (1.0CM) SCREW (M1.4), NEW TRUSTAR P2 (Silver)
2-662-396-21 SCREW (M1.4), NEW, TRUSTAR, P2 (Black) 3-208-537-01 0+Z M1.4X2 NEW TORASUTA (Red)
DSC-T100_L2 5-3
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-3. BT HOLDER SECTION
HARDWARE LIST
#26
105 104
MIC901
106 107 113 108 109
103
102
C901 BT001
110
! : BT001 (BATTERY, LITHIUM SECONDARY)
112 101
Board on the mount position. (See page 4-23.)
BT901 (Note)
111
Note: Refer to HELP "Installation method of battery terminal board" when changing the battery terminal board. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Ref. No. 110 110 110 111 0 112 * 113 0 BT001 BT901 0*C901 Part No. X-2177-161-1 X-2177-162-1 X-2177-163-1 1-873-402-11 1-480-014-21 3-208-925-01 1-756-710-11 1-780-456-11 1-114-382-11 Description HOLDER ASSY, BT (SILVER) HOLDER (BK) ASSY, BT (BLACK) HOLDER (RD) ASSY, BT (RED) BT-035 FLEXIBLE BOARD FLASH UNIT SHEET, SW INSULATING LITHIUM RECHARGEABLE BATTERY (MS614) TERMINAL BOARD, BATTERY (Note) CAP, ELECT 65uF 315V
· Refer to page 5-1 for mark 0. Ref. No. 101 * 102 103 103 103 104 105 106 107 108 109 Part No. A-1246-095-A 3-099-408-01 3-099-403-01 3-099-403-11 3-099-403-21 3-099-402-01 3-099-405-01 3-099-407-01 3-099-406-02 3-099-409-01 Description ST-162 FLEXIBLE BOARD, COMPLETE FRAME, RELEASE LID, DC (SILVER) LID, DC (BLACK) LID, DC (RED) HOLDER, MICROPHONE PLATE (REAR), INNER BASE, RELEASE BUTTON, RELEASE SPRING, RELEASE
1-873-403-11 SW-496 FLEXIBLE BOARD
MIC901 1-542-691-21 MICROPHONE BLOCK #26 2-635-591-11 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
DSC-T100_L2 5-4
BT-035
5-2. ELECTRICAL PARTS LIST
Ref. No. Part No. Description Ref. No. Part No. Description 1-873-402-11 BT-035 FLEXIBLE BOARD ******************** (BT901 is not included in BT-035 flexible board.) < BATTERY TERMINAL > BT901 1-780-456-11 TERMINAL BOARD, BATTERY
Electrical parts list of the CD-696, FP-636 flexible and MC-178 boards are not shown. Page 5-6 is not shown.
DSC-T100_L2 5-5
ST-162
Ref. No. Part No. Description Ref. No. Part No. Description A-1246-095-A ST-162 FLEXIBLE BOARD, COMPLETE ******************************* (BT001 (lithium battery), C901 (charging capacitor) and flash unit are not included in ST-162 flexible complete board.) 0 1-480-014-21 FLASH UNIT < BATTERY TERMINAL > 0 BT001 1-756-710-11 LITHIUM RECHARGEABLE BATTERY (MS614) < CAPACITOR > C001 C002 C006 C007 0* C901 1-165-908-11 1-100-611-91 1-100-758-11 1-164-933-11 1-114-382-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CAP, ELECT < DIODE > 0* D001 * D002 D003 6-501-433-01 DIODE MA2YF8000LS0 6-501-364-01 DIODE DOR5352 (SLEF-TIMER/AF ILLUMINATOR) 6-500-619-01 DIODE RB520S-40TE61 < IC > IC002 6-707-555-01 IC TPS65552RGTR < COIL > * L001 1-400-820-11 INDUCTOR < TRANSISTOR > 0* Q001 6-551-447-01 TRANSISTOR < RESISTOR > R001 R002 R003 R005 1-218-941-81 1-218-989-11 1-216-121-11 1-216-829-11 RES-CHIP RES-CHIP RES-CHIP METAL CHIP 100 1M 1M 4.7K 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W TIG022TS-S-TL-E 2.2uH 1uF 22uF 0.047uF 220PF 65uF 10% 20% 10% 10% 10V 6.3V 250V 50V 315V
SW-496
< TRANSFORMER > 0 T001 1-445-108-21 TRANSFORMER, D.C-D.C CONVERTER
1-873-403-11 SW-496 FLEXIBLE BOARD ******************** (All mounted parts except MIC901 are not supplied, though they are included in SW-496 flexible board. However MIC901 is not included in it.) < MICROPHONE > MIC901 1-542-691-21 MICROPHONE BLOCK
Electrical parts list of the SY-171 board is not shown. Pages 5-8 to 5-12 are not shown.
· Refer to page 5-1 for mark 0.
DSC-T100_L2 5-7
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Checking supplied accessories.
Note 1: This item is supplied with the unit as an accessory, but is not prepared as a service part.
Other accessories
2-319-287-01 2-319-287-11 2-319-287-21 2-319-287-31 2-319-287-41 2-319-287-51 2-319-287-61 2-319-287-71 2-319-287-81 2-319-287-91 2-319-288-11 2-319-288-21 2-319-288-31 2-319-288-41 2-319-288-51 2-319-288-61 2-319-288-71 2-319-288-81 2-319-288-91 2-319-289-11 2-319-289-21 2-319-289-31 2-319-289-41 2-319-289-51 2-319-289-61 HANDBOOK (PDF) (JAPANESE) (Note 2) HANDBOOK (PDF) (ENGLISH) (Note 2) HANDBOOK (PDF) (FRENCH) (Note 2) HANDBOOK (PDF) (ITALIAN) (Note 2) HANDBOOK (PDF) (SPANISH) (Note 2) HANDBOOK (PDF) (PORTUGUESE) (Note 2) HANDBOOK (PDF) (GERMAN) (Note 2) HANDBOOK (PDF) (DUTCH) (Note 2) HANDBOOK (PDF) (TRADITIONAL CHINESE) (Note 2) HANDBOOK (PDF) (SIMPLIFIED CHINESE) (Note 2) HANDBOOK (PDF) (RUSSIAN) (Note 2) HANDBOOK (PDF) (ARABIC) (Note 2) HANDBOOK (PDF) (PERSIAN) (Note 2) HANDBOOK (PDF) (KOREAN) (Note 2) HANDBOOK (PDF) (POLISH) (Note 2) HANDBOOK (PDF) (CZECH) (Note 2) HANDBOOK (PDF) (HUNGARIAN) (Note 2) HANDBOOK (PDF) (SLOVAK) (Note 2) HANDBOOK (PDF) (SWEDISH) (Note 2) HANDBOOK (PDF) (FINNISH) (Note 2) HANDBOOK (PDF) (NORWEGIAN) (Note 2) HANDBOOK (PDF) (DANISH) (Note 2) HANDBOOK (PDF) (THAI) (Note 2) HANDBOOK (PDF) (MALAY) (Note 2) HANDBOOK (PDF) (TURKISH) (Note 2)
Battery Charger Battery Charger BC-CSGB BC-CSGB 0 1-479-791-32 0 1-479-791-12 (J) (EXCEPT US, CND, 0 1-479-791-22 (US, CND) E: Latin America, BR, J) BC-CSGC 0 1-480-175-31 (E: Latin America)
USB, A/V Cable for Multi-use Terminal 1-829-866-51
Power Cord 0 1-555-074-91 (AUS) 0 1-782-476-71 (CH) 0 1-823-947-71 (KR) 0 1-827-269-31 (UK, HK) 0 1-827-826-41 (AEP, E) 0 1-828-050-31 (JE)
Rechargeable Battery Pack NP-BG1 (Note 1)
Battery Case (Note 1)
2-319-289-71 HANDBOOK (PDF) (GREEK) (Note 2) 2-319-290-01 MANUAL, INSTRUCTION (JAPANESE) (J) 2-319-290-12 MANUAL, INSTRUCTION (ENGLISH) (CND, AEP, UK, E, HK, AUS, JE) 2-319-290-22 MANUAL, INSTRUCTION (FRENCH, ITALIAN) (CND, AEP) 2-319-290-32 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (AEP, E, JE) 2-319-290-42 MANUAL, INSTRUCTION (GERMAN, DUTCH) (AEP) 2-319-290-52 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-319-290-72 MANUAL, INSTRUCTION (ARABIC, PERSIAN) (E) 2-319-290-82 MANUAL, INSTRUCTION (KOREAN) (KR, JE) 2-319-290-92 MANUAL, INSTRUCTION (POLISH, CZECH) (AEP) 2-319-294-12 2-319-294-22 2-319-294-32 2-319-294-42 2-319-294-52 MANUAL, INSTRUCTION (HUNGARIAN, SLOVAK) (AEP) MANUAL, INSTRUCTION (SWEDISH, FINNISH) (AEP) MANUAL, INSTRUCTION (NORWEGIAN, DANISH) (AEP) MANUAL, INSTRUCTION (THAI, MALAY) (E) MANUAL, INSTRUCTION (TURKISH, GREEK) (AEP)
Wrist Strap 2-050-981-01 (SILVER, RED) 2-050-981-11 (BLACK)
CD-ROM (Cyber-shot Application Software/ "Cyber-shot Handbook"/ "Cyber-shot Step-up Guide") 2-319-286-01 (EXCEPT US) 3-099-852-01 (US)
2-319-294-62 MANUAL, INSTRUCTION (ENGLISH, SPANISH) (US) Note 2: Handbooks (PDF) of each language are included in CD-ROM (Cyber-shot Application Software).
Conversion (2P) Adaptor 0 1-569-007-12 (JE)
Conversion (2P) Adaptor 0 1-569-008-12 (E: NTSC)
· Refer to the page 5-1 for mark 0.
DSC-T100_L2 5-13E
DSC-T100
LEVEL
2
SERVICE MANUAL
Ver. 1.1 2007.11
SUPPLEMENT-1
File this supplement with the service manual.
(DI07-224)
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Brazilian Model Japanese Model Tourist Model
· Change of Repair Parts
: Points changed portion.
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
Page Former New
5-2
#26
#71
8
#30
8
#30
(including CD-696 flexible complete board and IC001 (CCD imager)) (Note 2)
Ref. No. Part No. Description Ref. No. #71 Part No.
(including CD-696 flexible complete board and IC001 (CCD imager)) (Note 2)
Description
3-208-537-01 0+Z M1.4X2 NEW TORASUTA (Red)
51 57
51 57
5-3
#71
58
#26
#26
58
2-635-591-11 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
#71
3-208-537-01 0+Z M1.4X2 NEW TORASUTA (Red)
DSC-T100_L2
9-852-191-84
Sony EMCS Co.
2007K0500-1 © 2007.11 Published by Kohda TEC
HARDWARE LIST (1/4)
#1: M1.7 X 2.5 (Black) 2-635-562-11 #2: M1.7 X 4.0 (Black) 2-635-562-31 #3: M1.7 X 2.5 (Red) 2-660-401-01 #4: M1.4 X 2.5 (Tapping) (Dark Silver) 3-348-998-81
1.7 2.5 4.0
1.7
1.7
1.4
2.5
2.5
#5: M1.7 X 3.5 (Tapping) (Black) 3-080-204-01
#6: M1.4 X 1.7 (Silver) 2-598-474-01
#7: M1.7 X 1.6 (Black) 7-627-552-18
#8: M1.7 X 3.5 (Tapping) (Silver) 3-078-890-01
1.7
1.4
1.7
1.7
3.5
1.7
1.6
3.5
#9: M1.7 X 5.0 (Tapping) (Silver) 3-078-890-21
#10: M1.7 X 4.0 (Silver) 2-599-475-31
#11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11
#12: M1.7 X 5.0 (Tapping) (Black) 3-080-204-21
1.7 4.0
1.7
1.7
1.7
5.0
4.0
5.0
#13: M1.7 X 2.5 (Tapping) (Silver) 3-085-397-01
#14: M1.7 X 2.5 (Silver) 2-599-475-11
#15: M1.4 X 1.5 (Silver) 3-062-214-01
#16: M1.4 X 2.5 (Silver) 2-586-337-01
1.7 2.5
1.7 1.5
1.4
1.4
2.5
2.5
#17: M1.7 X 1.5 (Silver) 2-586-389-01
#18: M1.4 X 2.5 (Silver) 2-635-591-21
#19: M1.2 X 4.0 (Tapping) (Red) 3-086-156-21
#20: M1.4 X 3.0 (Silver) 2-635-591-31
1.7 2.2 1.5 3.5 2.5
1.4 4.0
1.2
1.4
3.0
HARDWARE LIST (2/4)
#21: M1.4 X 3.0 (Black) 2-662-396-21 #22: M1.7 X 5.0 (Tapping) (Silver) 3-083-261-01 #23: M1.7 X 4.0 (Tapping) (Black) 3-080-204-11 #24: B1.7 X 5.5 (Tapping) (Black) 4-679-805-11
1.4 5.0
1.7
1.7
1.7
3.0
4.0
5.5
#25: M1.7 X 3.0 (Black) 2-635-562-21
#26: M1.4 X 2.0 (Silver) 2-635-591-11
#27: M1.4 X 2.0 (Black) 2-662-396-11
#28: M1.4 X 4.0 (Tapping) (Dark Silver) 3-348-998-61
1.7 3.0
1.4
1.4 4.0
1.4
2.0
2.0
#29: M1.4 X 2.5 (Black) 2-662-396-01
#30: M1.2 X 4.0 (Tapping) (White) 3-086-156-11
#31: M3.0 X 4.0 (Silver) 2-102-434-01
#32: M2.0 X 4.5 (Tapping) (Silver) 2-102-498-01
1.4 3.5
1.2
3.0
2.0
2.5
4.0
4.5
#33: M3.0 X 6.0 (Silver) 3-077-331-21
#34: M3.0 X 8.0 (Black) 3-077-331-41
#35: M4.0 X 6.0 (Tapping) (Silver) 3-975-291-02
#36: M3.0 X 6.0 (Silver) 4-886-821-11
3.0 6.0 8.0
3.0
4.0
3.0
6.0
6.0
#37: M2.0 X 6.0 (Tapping) (Black) 3-080-206-31
#38: M3.0 X 20.0 (Tapping) (Silver) 7-685-651-79 3.0 2.0
#39: M2.6 X 5.0 (Tapping) (Black) 7-685-791-09
#40: M2.0 X 4.0 (Tapping) (Silver) 7-685-851-04
2.6 20.0 5.0 4.0
2.0
6.0
HARDWARE LIST (3/4)
#41: M3.0 X 8.0 (Tapping) (Silver) 3-065-748-01 #42: M2.0 X 4.0 (Tapping) (Silver) 7-628-253-00 #43: M1.7 X 4.0 (Red) 2-660-401-31 #44: M1.7 X 3.0 (Tapping) (Silver) 3-078-890-61
3.0
2.0
1.7
1.7
8.0
4.0
4.0
3.0
#45: M1.4 X 2.5 (Silver) 2-587-151-01
#46: M1.7 X 3.0 (Red) 2-660-401-11
#47: M1.4 X 3.0 (Tapping) (Silver) 2-665-774-01
#48: M1.7 X 2.5 (Silver) 3-973-497-91
1.4 3.0
1.7
1.4
1.7
2.5
3.0
2.5
#49: M2.0 X 4.0 (Black) 2-630-005-31
#50: M2.0 X 3.0 (Red) 2-891-494-11
#51: M2.0 X 2.5 (Silver) 3-073-686-01
#52: M2.0 X 4.0 (Tapping) (Black) 3-080-206-11
2.0
2.0
2.0 4.0 2.5
2.0
4.0
3.0
#53: M2.0 X 5.0 (Tapping) (Black) 3-080-206-21
#54: M1.75 X 6.0 (Tapping) (Black) 3-318-203-11
#55: M2.0 X 4.0 (Silver) 2-655-582-11
#56: M2.0 X 3.5 (Silver) 3-067-187-11
2.0 5.0 6.0
1.75
2.0
2.0
4.0
3.5
#57: M1.7 X 4.0 (Black) 7-627-852-18
#58: M2.0 X 6.0 (Tapping) (Silver) 3-719-408-11
#59: M2.0 X 5.0 (Tapping) (Silver) 3-080-205-21
#60: M2.6 X 5.0 (Black) 3-061-062-11
1.7 4.0 6.0
2.0 5.0
2.0 5.0
2.6
HARDWARE LIST (4/4)
#61: M3.0 X 10.0 (Black) 7-682-549-09 #62: M2.0 X 3.0 (Silver) 3-080-202-21 #63: M5.0 X 12.5 (Black) 3-060-811-21 #64: M1.7 X 5.0 (Tapping) (Silver) 2-666-551-21
3.0 10.0
2.0 12.5
5.0 5.0
1.7
3.0
#65: M1.4 X 3.5 (Silver) 2-635-591-01
#66: M1.4 X 1.4 (Silver) 2-635-591-41
#67: M1.4 X 2.0 (Silver) 3-389-523-16
#68: M1.7 X 4.0 (Silver) 2-655-581-01
1.4
1.4 2.0
1.4
1.7
3.5
1.4
4.0
#69: M1.7 X 3.0 (Silver) 2-599-475-21
#70: M1.7 X 5.0 (Silver) 2-599-475-41
#71: M1.4 X 2.0 (Red) 3-208-537-01
1.7 3.0 5.0
1.7
1.4
2.0
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar Printing a text
1. Click the Print button . 2. Specify a printer, print range, number of copies, and other options, and then click [OK].
Reversing the screens displayed once
· To reverse the previous screens (operation) one by one, click . the · To advance the reversed screens (operation) one by one, click the .
Application of printing:
To set a range to be printed within a page, select the graphic and drag on the page to enclose a range to selection tool be printed, and then click the Print button.
Application to the Service Manual:
This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it will be convenient for the voltage check.
Finding a text
1. Click the Find button . 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary)
Moving with link
1. Select either palm tool , zoom tool , text selection tool
Application to the Service Manual:
To execute "find" from current page toward the previous pages, select the check box "Find Backward" and then click the "Find".
, or graphic selection tool . 2. Place the pointer in the position in a text where the link exists (such as a button on cover and the table of contents page, or blue characters on the removal flowchart page or drawing page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:
Click an item (text) on the bookmark pallet, and you can move can display the to the link destination. Also, clicking hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.)
Application to the Service Manual:
The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on the circuit diagram or printed circuit board diagram successively. Note: The find function may not be applied to the Service Manual depending on the date of issue.
Zooming or rotating the screen display
"Zoom in/out" · Click the triangle button in the zoom control box to select the display magnification. Or, you may click ing in or out. or for zoom-
Switching a page
· To move to the first page, click the · To move to the last page, click the · To move to the next page, click the . . . . "Rotate" · Click rotate tool , and the page then rotates 90 degrees each.
· To move to the previous page, click the
Application to the Service Manual:
The printed circuit board diagram you see now can be changed to the same direction as the set.
Reverse
985219132.pdf
Revision History
Ver. 1.0 1.1 Date 2007.02 2007.11 History Official Release Supplement-1 (S1 DI07-224) Contents -- · Change of Repair Parts S.M. Rev. issued -- No
DSC-T100_L2