Text preview for : SONY MHS-CM1 SERVICE MANUAL VER 1.0 2008.12 (9-852-640-11).pdf part of SONY MHS-CM1 SONY MHS-CM1
MOBILE HD SNAP CAMERA.
SERVICE MANUAL VERSION 1.0 2008.12
PART#(9-852-640-11)
Back to : SONY MHS-CM1 SERVICE MANU | Home
MHS-CM1
SERVICE MANUAL
US Model
Ver. 1.0 2008.12
Revision History
Internal memory
ON BOARD
Photo: Silver
Link
SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST
SERVICE NOTE BLOCK DIAGRAM
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
In case of the main board or main frame assy failure, contact
your local Sony Service Headquarter for the measures.
MOBILE HD SNAP CAMERA
2008L0500-1
MHS-CM1 © 2008.12
9-852-640-11 Sony EMCS Co. Published by Kohda TEC
SPECIFICATIONS
Camera [Power, general] Rechargeable battery pack
Power: Lithium ion battery (built-in), 7.2 V Used battery: Lithium-ion battery (built-in)
[System] AC-DL960 AC Adaptor (supplied), 9.6 V
Image device: 7.13 mm (1/2.5 type) CMOS Maximum voltage: DC 8.4 V
Power consumption: 2.3 W (when the movie Nominal voltage: DC 7.2 V
sensor
image size is [720 30P])
Total pixel number of camera: Maximum charge voltage: DC 8.4 V
Operating temperature: 0 to 40°C (32 to 104°F)
Approx. 5 040 000 (2 592 × 1 944) pixels Maximum charge current: 500 mA
Storage temperature: 20 to +60°C (4 to +140°F)
Effective pixel number of camera: Capacity: 3.6 Wh (500 mAh)
Approx. 5 040 000 (2 592 × 1 944) pixels Dimensions: Approx. 43 × 61 × 105 mm (1 3/4 ×
(still images), Approx. 2 073 600 (1 440 × 2 1/2 × 4 1/4 inches) (W/H/D, excluding
protrusions)
1 080) pixels (movies) Trademarks
Lens: F3.3 Mass: Approx. 210 g (7 oz) (including strap, etc.)
· "Memory Stick", , "Memory Stick PRO",
f = 6.4 to 31.4 mm (9/32 to 1 1/4 inches) Microphone: Monaural
, "Memory Stick Duo",
f = 38 to 190 mm (1 1/2 to 7 1/2 inches) (4:3) Speaker: Monaural , "Memory Stick PRO
when converted to a 35 mm still camera Exif Print: Compatible Duo", , , "Memory
f = 41 to 203 mm (1 5/8 to 8 inches) (16:9) Stick Micro", "MagicGate", and
PRINT Image Matching III: Compatible
when converted to a 35 mm still camera are trademarks of Sony
Exposure control: Automatic exposure, Scene AC-DL960 AC Adaptor Corporation.
Selection (4 modes) · Microsoft, Windows, Windows Vista and
Power requirements: AC 100 V to 240 V,
File format: DirectX are either registered trademarks or
50 Hz/60 Hz
Still images: Exif Ver. 2.21 JPEG compliant, trademarks of Microsoft Corporation in the
DCF compliant Output voltage: DC 9.6 V (See the lavel on the
United States and/or other countries.
Movies: MPEG-4 compliant (.MP4) AC Adaptor for other specifications.)
· Macintosh, Mac OS, iMac, iBook, PowerBook,
Video codec type: MPEG-4 AVC/ Operating temperature: 0 to 40°C (32 to 104°F)
Power Mac and eMac are trademarks or
H.264 Main Profile Storage temperature: 20 to +60°C (4 to registered trademarks of Apple Inc.
Audio codec type: AAC LC +140°F)
· Intel, MMX, and Pentium are trademarks or
Recording media: Internal Memory (approx. Dimensions: Approx. 48 × 29 × 81 mm (1 15/16 × registered trademarks of Intel Corporation.
12 MB), "Memory Stick PRO Duo" media 1 3/16 × 3 1/4 inches) (W/H/D) In addition, system and product names used in this
[Input and Output connectors] Mass: Approx. 130 g (4 oz) excluding the power manual are, in general, trademarks or registered
cord (mains lead) trademarks of their respective developers or
USB jack: mini B, Hi-Speed USB (USB 2.0 manufacturers. However, the TM or ® marks are
compliant) not used in all cases in this manual.
Design and specifications are subject to change
A/V OUT jack: Minijack, Video out, audio out
without notice.
(mono)
[LCD screen]
LCD panel: 6 cm (2.5 type) TFT drive
Total number of dots: 153 600 (640 × 240) dots
MHS-CM1
--2--
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. · Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
· Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
· Strong viscosity
· Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
· Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. · Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
MHS-CM1
--3--
1. SERVICE NOTE
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note 1: When replacing the main frame assy, erase the data in internal memory of the board before replacement.
Note 2: When replacing the main frame assy, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to "Memory Stick PRO Duo" media.
1 Insert "Memory Stick PRO Duo" media.
2 Select [Copy] with v/V/b/B on the control button, then press B.
3 Select [OK] with v, then press z.
The message "All data in internal memory will be copied" appears.
4 Select [OK] with v, then press z.
Copying starts.
To cancel the copying
Select [Cancel] in step 4, then press z.
· Charge the battery sufficiently. Copying image files when the remaining battery amount is low can cause
data transfer failure or damage the data due to battery exhaustion.
· You cannot copy individual images.
· The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the "Memory Stick PRO Duo" media after copying, then execute the [Format]
command in [Internal Memory Tool].
· When you copy the data in the internal memory to the "Memory Stick PRO Duo" media, a new folder is
created. You cannot choose a specific folder on the "Memory Stick PRO Duo" media as the destination for
the data to be copied.
· Even if you copy data, a (Sharemark) or a (Print order) mark is not copied.
Method for Formatting the Internal Memory
This item appears only when "Memory Stick PRO Duo" media is not inserted in the camera.
Format
Formats data stored in the internal memory.
· Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V/b/B on the control button, then press B.
2 Select [OK] with v, then press z.
The message "All data in internal memory will be erased" appears.
3 Select [OK] with v, then press z.
The format is completed.
To cancel the formatting
Select [Cancel] in step 3, then press z.
MHS-CM1
1-1E
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
2 3 2
4
1
1
1
1 M1.4_3_A0.3_D2.5_CR_R 1 TP_1.4_4_A0.3_D2.5_C
2 REAR COVER 2 TP_1.4_3.5_A0.3_D2.5_B
3 KEY TOP R
4 CABINET (R) ASSY
4
5
2 3
5
7
7
6
(To page 2-2)
2 6
3
3
5
1
1
8 3 4
1 TP_1.4_3.5_A0.3_D2.5_B 1 LENS CAP
2 TP_1.4_4_A0.3_D2.5_C 2 TP_1.4_4_A0.3_D2.5_C
3 TP_1.4_3.5_A0.3_D2.5_B 3 TP_1.4_3.5_A0.3_D2.5_B
4 CABINET (L) ASSY 4 CENTER CABINET PIN
5 TP_1.4_3.5_A0.3_D2.5_B 5 TP_1.4_3.5_A0.3_D2.5_B
6 JACK HOLDER 6 SW (TOP) BOARD
7 JACK BOARD 7 TOP+F CABINET ASSY
8 LITHIUM BATTERY
MHS-CM1
2-1
7
0 3 qf
qa
9
8 qg
5
qs qd
6 1
5
4
(From page 2-1)
1
2
2 3
2 2
1 TP_1.4_3.5_A0.3_D2.5_B 1 BATTERY TERMINAL FLEXIBLE BOARD
2 TP1.7_4.5_A0.5_D3_CR 2 TP_1.4_2.8_A0.3_D2.5_B
3 M1.7_3.5_A0.3_D2.5_CR_R 3 MAIN BOARD
4 CAB PANEL (O) ASSY
5 TP_1.4_2.8_A0.3_D2.5_B
6 PLATE-LCD
7 TP_1.4_2.8_A0.3_D2.5_B
8 HINGE CABINET (OUT)
9 HINGE CABINET (IN)
0 MAGNET (PANEL)
qa HINGE ASSY
qs LCD BOARD
qd LCD PANEL
qf MAGNET (PANEL)
qg PANEL CABINET (IN)
MHS-CM1
2-2E
3. BLOCK DIAGRAM
3-1. OVERALL BLOCK DIAGRAM
5 4 3 2 1
DDR DSP_1/3 SWITCH
LENS +1.8V_DDR2 RAMD[0..15] +3.3VD
+1.8V_DDR2 RAMD[0..15] RAMBA[0..2] RAMD[0..15] PLAY_LED +3.3VD +3.3VS
RAMBA[0..2] RAMA[0..12] RAMBA[0..2] PLAY_LED PLAY_LED +3.3VS DGND PCB_SW
RAMA[0..12] RAMCLK_N RAMA[0..12] VERSION DGND HALL_GND
IRIS DGND RAMCLK_N RAMCLK RAMCLK_N VERSION HALL_GND
(MOTER) DGND RAMCLK RAMWE_N RAMCLK PHOTO_S1
RAMWE_N RAMRAS RAMWE_N PHOTO_S1 PHOTO_S2
RAMRAS RAMCAS RAMRAS PHOTO_S2 K_ADC MODE
RAMCAS RAMCAS K_ADC
RAMLDM
RAMLDM
RAMUDM RAMLDM K_REC
K_REC
K_TRASH K_REC K_RESET
K_RESET
K_POWER
DIAL
RAMUDM RAMLDQS_N RAMUDM K_TRASH K_DISP K_TRASH K_POWER K_MARK
RAMLDQS_N RAMLDQS RAMLDQS_N K_DISP K_DISP K_MARK WIDE
D RAMLDQS
RAMUDQS_N
RAMUDQS_N
RAMUDQS
RAMLDQS
RAMUDQS_N W_LED
W_LED WIDE
TELE
TELE
TS
D
RAMUDQS RAMODT RAMUDQS SHUT1 TS
RAMODT RAMCLK_EN RAMODT SHUT1 SHUT2
RAMCLK_EN RAMCLK_EN SHUT2 SWITCH
SENSOR_VD CMOS_PWR
DDR CMOS_TRIG SENSOR_VD CMOS_PWR
CMOS_STANDBY CMOS_TRIG UART0_RX
CMOS_RST# CMOS_STANDBY UART0_RX UART0_TX
CMOS_SCLK CMOS_RST# UART0_TX DC_DET
ZOOM SENSOR CMOS_SDATA CMOS_SCLK DC_DET
MOTOR DRIVER CMOS_SDATA DGND
LCD_SDATA LENS_SEN DGND +3.3VD
ZOOM MOTER LCD_SCLK LCD_SDATA LENS_SEN MOTO_EXT1 LENS_SEN +3.3VD +1.8V_DDR2
THRM2 LCD_SCLK MOTO_EXT1 MOTO_EXT2 MOTO_EXT1 +1.8V_DDR2
MOTO_RESET THRM2 MOTO_EXT2 MOTO_MOB1 MOTO_EXT2
FOCUS SENSER +3.3VD MOTO_RESET MOTO_MOB1 MOTO_MOB2 MOTO_MOB1 +2.8VD
+4VM +3.3VD MOTO_MOB2 MOTO_MCLK MOTO_MOB2 +2.8VD
+4VM MOTO_MCLK MOTO_MCLK LCD
FOUCE MOTER DGND
SHUT1 DGND AF_PI LCD_CLK_CTL +3.3VD
SHUT2 SHUT1 AF_PI ZOOM_PI AF_PI LCD_CLK_CTL BL_PWM +3.3VD
SHUT2 ZOOM_PI ZOOM_PI BL_PWM BL_POWER BL_PWM +4VM
IRIS MOTER CF_STSCHG BL_POWER LCD_SEN BL_POWER +4VM
MOTOR DRIVER NAND_CE2 CF_STSCHG LCD_SEN LCD_SCLK LCD_SEN
SHUTTER SENSER
NAND_CE2 LCD_SCLK LCD_SDATA LCD_SCLK 2.5'' inch
LCD_SDATA LCD_SDATA DGND
MS_LED DGND LCD
MS_LED
HIC_DET1
HIC_DET1 HIC2
PANEL
PWR_HOLD HIC2 HIC2
PWR_HOLD VD_OUT6
NAND VD_OUT6 VD_OUT6
NAND_WP VD_OUT7 VD_OUT7
VD_OUT10 VD_OUT7
NAND_WP NAND_WP VD_OUT10
LCD_backlight
+3.3VD
+3.3VD DSP_1/3
DGND
DGND
C NAND_IO[0..7]
DSP_2/3
VD_OUT10
3 LED 1 C
NAND_IO[0..7] NAND_CE NAND_IO[0..7] VD_OUT10 LCD_VD
NAND_CE NAND_R/B NAND_CE LCD_VD LCD_HD LCD_VD
NAND_R/B NAND_RE NAND_R/B LCD_HD LCD_MCLK LCD_HD
NAND_RE NAND_WE NAND_RE LCD_MCLK LCD_MCLK
NAND_WE NAND_ALE NAND_WE VD_OUT[0..5]
NAND_ALE NAND_CLE NAND_ALE VD_OUT[0..5] VD_OUT[0..5]
NAND_CLE NAND_CLE
LCD_CLK_CTL LCD
LCD_CLK_CTL
NAND K_ADC
K_ADC CMOS
THRM2
THRM2 CMOS_MCLK CMOS_SCLK
UART0_RX CMOS_MCLK CMOS_PIXCLK CMOS_MCLK CMOS_SCLK CMOS_SDATA
UART0_TX UART0_RX CMOS_PIXCLK CMOS_VD CMOS_PIXCLK CMOS_SDATA CMOS_RST#
UART0_TX CMOS_VD CMOS_HD CMOS_VD CMOS_RST# CMOS_TRIG
MS CARD CMOS_HD CMOS_HD CMOS_TRIG
CMOS_D[0..11] CMOS_STANDBY
CMOS_D[0..11] SENSOR_VD CMOS_D[0..11] CMOS_STANDBY CMOS_PWR FPC_CMOS
SENSOR_VD CMOS_PWR
CF_STSCHG
CF_STSCHG NAND_CE2
NAND_CE2 +3.3VD
RESET +2.8VD +3.3VD +1.8V_DDR2
RESET NAND_RE RESET +2.8VD +2.8VD +1.8V_DDR2 DGND
NAND_RE NAND_WE DGND
NAND_WE NAND_ALE K_MARK PCB_TOP
NAND_ALE NAND_IO[0..7] K_MARK TELE SW1
NAND_IO[0..7] NAND_IO[0..7] TELE
NAND_CLE
NAND_CLE
WIDE
WIDE 1 A B 2
CMOS
CF_D[11..15] PHOTO_S1
CF_D[11..15] CF_A[0..2] CF_D[11..15] PHOTO_S1 PHOTO_S2
6 5 PHOTO SHUT
Memory Stick CF_A[0..2] CF_CE1 CF_A[0..2] PHOTO_S2 3
C D
4
MS_LED CF_CE1 CF_CE2 CF_CE1
MS_LED CF_CE2 CF_CE2
1
3
4
CF_WP
MS_PWR CF_WP CF_IORD CF_WP
7 6 TELE/WIDE CMOS
A
B
C
MS_PWR CF_IORD CF_WAIT CF_IORD 7 6
CF_WAIT CF_WAIT 2 A. C. 5
CF_RESET
CF_RESET CF_RESET SW2
B +3.3VD
+3.3VD
+1.8V_DDR2
B
+1.8V_DDR2 DGND
DGND
BAT CHARGER
K_POWER_DET USB5V
MS_PWR K_POWER_DET USB5V USB_D+
SPKR_ON MS_PWR USB_D+ USB_D- PWR_CTRL +3.3VS
SPEAKER SPKR_ON USB_D- PWR_CTRL +3.3VS
MOTO_RESET VIDEO_IOR VP
DGND MOTO_RESET VIDEO_IOR VIDEO_IOG VP
DGND +3.3VD DGND VIDEO_IOG VIDEO_IOB DC_DET +3.3VD
+3.3VD +1.0VD +3.3VD VIDEO_IOB C_DET DC_DET +3.3VD
+1.0VD BAT_LEVEL +1.0VD C_DET VERSION TS DGND
VP BAT_LEVEL BAT_LEVEL VERSION TS DGND
VP
DSP_2/3
+1.8V_DDR2 BAT CHARGER
+1.8V_DDR2 DSP_3/3
C_DET
PWR_CTRL C_DET VIDEO_IOB
PWR_CTRL +4VM VIDEO_IOB VIDEO_IOG
+4VM +4VM VIDEO_IOG VIDEO_IOR TV
+3.3VS VIDEO_IOR SPKR_ON
+3.3VS +3.3VS SPKR_ON W_LED
+3.3VD W_LED USB5V
+3.3VD USB5V USB_D+
POWER DGND USB_D+ USB_D- PC
DGND USB_D-
DSP_3/3
A A
5 4 3 2 1
MHS-CM1
3-1E
4. REPAIR PARTS LIST
(ENGLISH)
NOTE: When indicating parts by reference number,
· -XX, -X mean standardized parts, so they may have some differences from please include the board name.
the original one.
· Items marked "*" are not stocked since they are seldom required for routine The components identified by mark 0 or
service. Some delay should be anticipated when ordering these items. dotted line with mark 0 are critical for safety.
· The mechanical parts with no reference number in the exploded views are not Replace only with part number specified.
supplied. Les composants identifiés par une marque
· Due to standardization, replacements in the parts list may be different from 0 sont critiques pour la sécurité.
the parts specified in the components used on the set. Ne les remplacer que par une pièce portant
le numéro spécifié.
· Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet's Color
(Silver) : Parts Color
· Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
MHS-CM1
4-1
4-1. EXPLODED VIEWS
4-1-1. OVERALL SECTION
ns: not supplied
2 3 3
1 3 4 9
8
7
ns
J1
Main Frame Section
JC2 JC1
(see page 4-4)
10
5
7 3
3
13
3 12
3 LCD Section
(see page 4-3)
6
3 3
1
1 3
16 3 11
3
3
1
3 1
18 15
15
3 17
14
19
· Refer to page 4-1 for mark 0.
Ref. No. Part No. Description Ref. No. Part No. Description
1 3-277-535-01 TP_1.4_4_A0.3_D2.5_C 12 4-134-371-01 KEY TOP R (SILVER) (SILVER)
2 X-2345-574-1 CABINET (L) ASSY (SILVER) (SILVER) 12 4-134-372-01 KEY TOP R (ORANGE) (ORANGE)
2 X-2345-575-1 CABINET (L) ASSY (ORANGE) (ORANGE) 12 4-134-373-01 KEY TOP R (VIOLET) (VIOLET)
2 X-2345-576-1 CABINET (L) ASSY (VIOLET) (VIOLET) 13 X-2345-562-1 CABINET (R) ASSY (SILVER) (SILVER)
3 3-277-534-01 TP_1.4_3.5_A0.3_D2.5_B 13 X-2345-563-1 CABINET (R) ASSY (ORANGE) (ORANGE)
4 A-1675-938-A JACK BOARD, COMPLETE 13 X-2345-564-1 CABINET (R) ASSY (VIOLET) (VIOLET)
5 4-134-386-01 HOLDER, JACK 0 14 A-1599-878-A SQX-3185 (UC)
6 X-2345-565-1 CABINET ASSY (SILVER), TOP+F (SILVER) 15 4-134-405-01 TP1.7_4.5_A0.5_D3_CR
6 X-2345-566-1 CABINET ASSY (ORANGE), TOP+F (ORANGE) 16 A-1675-936-A SW (TOP) BOARD, COMPLETE
6 X-2345-567-1 CABINET ASSY (VIOLET), TOP+F (VIOLET) 17 4-136-943-01 PIN, CENTER CABINET
7 3-277-533-01 TP_1.4_2.8_A0.3_D2.5_B 18 4-134-400-01 CAP, LENS
8 A-1675-933-A SW (REAR) BOARD, COMPLETE 19 4-142-014-01 CUSHION, BATTERY
9 4-134-370-01 KEY TOP (REAR) J1 4-134-399-01 CONNECTOR, USB
10 X-2345-561-1 CABINET ASSY, REAR JC1 1-815-794-13 CONNECTOR (MULTIPLE) (A/V OUT)
11 4-134-404-01 M1.4_3_A0.3_D2.5_CR_R JC2 4-134-398-01 JACK, DC (DC IN)
MHS-CM1
4-2
4-1-2. LCD SECTION
ns: not supplied
54
54 51
60 55 59
58 59
57
53
55 (Note) 52
(Note)
55
ns
55
55
56
Note: The adjustment is not required after replacing the LCD
panel and the LCD board.
Ref. No. Part No. Description Ref. No. Part No. Description
51 4-134-379-01 CABINET (IN), PANEL 56 X-2345-572-1 CAB PANEL (O) ASSY (CM1VIOLET) (VIOLET)
52 4-134-380-01 PANEL, LCD (Note) 57 4-134-381-01 CABINET (OUT (SILVER)), HINGE (SILVER)
53 A-1675-937-A LCD BOARD, COMPLETE (Note) 57 4-134-382-01 CABINET (OUT (ORANGE)), HINGE (ORANGE)
54 4-134-403-01 M1.7_3.5_A0.3_D2.5_CR_R
55 3-277-533-01 TP_1.4_2.8_A0.3_D2.5_B 57 4-134-383-01 CABINET (OUT (VIOLET)), HINGE (VIOLET)
58 X-2345-573-1 HINGE ASSY
56 X-2345-570-1 CAB PANEL (O) ASSY (CM1SILVER) (SILVER) 59 4-134-385-01 MAGNET (PANEL)
56 X-2345-571-1 CAB PANEL (O) ASSY (CM1ORANGE) 60 4-134-384-01 CABINET (IN), HINGE
(ORANGE)
MHS-CM1
4-3
4-1-3. MAIN FRAME SECTION
ns: not supplied
ns
(Note)
104
101
102
103 102
102
ns
(Note)
102 102
Note: In case of the main board or main frame assy failure,
contact your local Sony service Headquarter for the
measures.
Ref. No. Part No. Description Ref. No. Part No. Description
101 4-134-396-01 SPEAKER 104 A-1700-049-A BATTERY TERMINAL FLEXIBLE BOARD,
102 3-277-533-01 TP_1.4_2.8_A0.3_D2.5_B COMPLETE
103 A-1675-942-A LIGHT BOARD, COMPLETE
MHS-CM1
4-4
4-2. ACCESSORIES
Checking supplied accessories.
AC Adaptor Power Cord Lens Cap Lens Cap String
(AC-DL960) 0 1-790-107-61 4-134-400-01 4-134-401-01
0 1-487-165-11
Mobile HD Snap Camera Handbook (PDF)
The CD-ROM supplied contains all of language version of
Component A/V Cable A/V Connecting Cable the Mobile HD Snap Camera Handbook (PDF) for printing.
1-834-646-11 1-823-156-61 The printed matter is not supplied. If required, please
order it with the part number below.
* 4-123-312-11 (ENGLISH)
* 4-123-312-21 (FRENCH)
* 4-123-312-31 (SPANISH)