Text preview for : SONY HCD-RV7, RV8 SERVICE MANUAL VER 1.0 2002.07 ( 9-874-091-01).pdf part of SONY HCD-RV7, RV8 SONY HCD-RV7, RV8
COMPACT DISC DECK RECEIVER.
SERVICE MANUAL VERSION 1.0 2002.07
PART#(9-874-091-01)
Back to : SONY HCD-RV7, RV8 SERVICE | Home
HCD-RV7/RV8
SERVICE MANUAL
Ver 1.0 2002.07
E Model
HCD-RV7/RV8 are the amplifier, video CD/CD player, tape player and tuner section in MHC-RV7/RV8.
Photo: HCD-RV8
Model Name Using Similar Mechanism CD Section CD Mechanism Type Base Unit Name Optical Pick-up Name TAPE Section Model Name Using Similar Mechanism Tape Transport Mechanism Type
NEW CDM58E-30BD62 BU-30BD62 A-MAX.3 NEW TCM-230AWR41CS
SPECIFICATIONS
Amplifier section
Saudi Arabian Models The following are measured at AC 127, 220, 240V, 50/60 Hz DIN power output (rated) 160 + 160 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 210 + 210 watts (HCD-RV8) 200 + 200 watts (HCD-RV7) (6 ohms at 1 kHz, 10% THD) Other Models The following are measured at AC 120, 220, 240V 50/60 Hz DIN power output (rated) 160 + 160 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 210 + 210 watts (HCD-RV8) 200 + 200 watts (HCD-RV7) (6 ohms at 1 kHz, 10% THD) Inputs GAME (VIDEO): 1 Vp-p, 75 ohms (phono jack) GAME (AUDIO): Voltage 250 mV, (phono jacks) impedance 47 kilohms MD/VIDEO (AUDIO) IN: voltage 450 mV/250 mV, (phono jacks) impedance 47 kilohms MIC: sensitivity 1 mV, (phone jack) impedance 10 kilohms Outputs VIDEO OUT: (phono jacks)
Tuner section
max. output level 1 Vp-p, unbalanced, Sync. negative load impedance 75 ohms
FM stereo, FM/AM superheterodyne tuner
FM tuner section
AUDIO OUT: (phono jacks) PHONES: (stereo mini jack) FRONT SPEAKER:
Voltage 250 mV impedance 47 kilohms accepts headphones of 8 ohms or more accepts impedance of 6 to 16 ohms SURROUND SPEAKER: accepts impedance of 24 ohms or more SUBWOOFER: accept impedance of (RV8) 8 ohms or more
Tuning range Antenna Antenna terminals Intermediate frequency
AM tuner section
87.5 108.0 MHz FM lead antenna 75 ohm unbalanced 10.7 MHz
Tuning range Latin American models: 530 1,710 kHz (with the interval set at 10 kHz) 531 1,710 kHz (with the interval set at 9 kHz) 531 1,602 kHz (with the interval set at 9 kHz) 531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) AM loop antenna External antenna terminal 450 kHz
VIDEO CD/CD player section
System Compact disc and digital audio system Laser Semiconductor laser (=795nm) Frequency response 2 Hz 20 kHz (±0.5 dB) Wave length 795 nm Video color system format NTSC, PAL Saudi Arabian models: Other models:
Tape player section
Recording system Frequency response 4-track 2-channel stereo 50 13,000 Hz (±3 dB), using Sony TYPE I cassette Antenna Antenna terminals Intermediate frequency
Continued on next page
COMPACT DISC DECK RECEIVER
9-874-091-01
2002G0500-1 C 2002.07
Sony Corporation
Home Audio Company Published by Sony Engineering Corporation
HCD-RV7/RV8
General
Power requirements Thailand models: Saudi Arabian models: 220 V AC, 50/60 Hz 120 127 V, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector 120 V, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector 300 watts (HCD-RV8) 240 watts (HCD-RV7) Approx. 280 x 360 x 445 mm Approx. 13.1 kg (HCD-RV8) Approx. 11.0 kg (HCD-RV7)
Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270 °C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Other models:
Power consumption Dimensions (w/h/d) Mass :
Design and specifications are subject to change without notice.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
The following caution label is located inside the unit.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-RV7/RV8
TABLE OF CONTENTS 1. 2. SERVICING NOTES ................................................ 4 GENERAL
Location of Controls ....................................................... 5 Setting the Clock ............................................................. 6 7-27. Printed Wiring Boards PANEL/CD OPEN/CD SWITCH Boards ................ 7-28. Schematic Diagram PANEL/CD OPEN/CD SWITCH Boards ................ 7-29. Printed Wiring Boards PAD SWITCH/VOL Boards ..................................... 7-30. Schematic Diagram PAD SWITCH/VOL Boards ..................................... 7-31. Printed Wiring Boards MAIN TRANS/SUB-TRANS Boards ...................... 7-32. Schematic Diagram MAIN TRANS/SUB-TRANS Boards ...................... 7-33. IC Pin Function Description ........................................... 48 49 50 51 52 53 56
3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9.
DISASSEMBLY
7 8 8 9 9 10 10 11 11 12 12 13
Disassembly Flow ........................................................... Top Case .......................................................................... Loading Panel .................................................................. CD Mechanism Deck (CDM58E-30BD62) ................... Front Panel Section ......................................................... Back Panel Section .......................................................... MAIN Board ................................................................... BU-30 (61) Assy ............................................................. DRIVER Board, MOTOR Board, SENSOR (CD) Board and VIDEO Board ...................... 3-10. Tape Mechanism Deck (TCM-230AWR41CS) .............. 3-11. Belt .................................................................................. 3-12. SW Board, HEAD (A) Board and HEAD (B) Board .....
8.
8-1. 8-2. 8-3. 8-4. 8-5. 8-6.
EXPLODED VIEWS
Panel Section ................................................................... Front Panel Section ......................................................... Chassis Section ............................................................... CD Mechanism Deck Section (CDM58E-30BD62) ...... Base Unit Section (BU-30BD62) ................................... Tape Mechanism Deck Section (TCM-230AWR41CS) .................................................... 65 66 67 68 69 70
4. 5. 6.
TEST MODE .............................................................. 14 MECHANICAL ADJUSTMENTS ....................... 18 ELECTRICAL ADJUSTMENTS
Deck section .................................................................... 18 CD Section ...................................................................... 21 VIDEO Section ............................................................... 21
9.
ELECTRICAL PARTS LIST ............................... 71
7.
7-1. 7-2. 7-3. 7-4. 7-5. 7-6. 7-7. 7-8. 7-9. 7-10. 7-11. 7-12. 7-13. 7-14. 7-15. 7-16. 7-17. 7-18. 7-19. 7-20. 7-21. 7-22. 7-23. 7-24. 7-25. 7-26.
DIAGRAMS
Block Diagram CD SERVO Section ....................... Block Diagram AUDIO/VIDEO CD Section .......... Block Diagram TUNER/TAPE DECK Section ...... Block Diagram MAIN Section ................................ Block Diagram DISPLAY/KEY CONTROL/ POWER SUPPLY Section ........................................... Note for Printed Wiring Boards and Schematic Diagrams ....................................................... Printed Wiring Board BD Board ............................. Schematic Diagram BD Board ................................ Schematic Diagram VIDEO Board (1/2) ................ Schematic Diagram VIDEO Board (2/2) ................ Printed Wiring Board VIDEO Board ....................... Printed Wiring Boards DRIVER/MOTOR/SENSOR (CD) Boards .............. Schematic Diagram DRIVER/MOTOR/SENSOR (CD) Boards .............. Printed Wiring Boards SW/HEAD (A)/HEAD (B) Boards .......................... Schematic Diagram SW Board ................................ Printed Wiring Board MAIN Board ........................ Schematic Diagram MAIN Board (1/4) .................. Schematic Diagram MAIN Board (2/4) .................. Schematic Diagram MAIN (3/4)/HEAD (A)/HEAD (B) Boards ............. Schematic Diagram MAIN Board (4/4) .................. Printed Wiring Board GAME IN Board .................. Schematic Diagram GAME IN Board ..................... Printed Wiring Board SUB WOOFER Board ......... Schematic Diagram SUB WOOFER Board ............ Printed Wiring Boards POWER/SENSOR Boards ........................................ Schematic Diagram POWER/SENSOR Boards ........................................ 22 23 24 25 26 27 28 29 30 31 32 33 33 34 35 37 38 39 40 41 42 43 44 45 46 47
3
HCD-RV7/RV8 SECTION 1 SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the "S curve check" in "CD section adjustment" and check that the S curve waveforms is output three times. MODEL RV7: E, Singapore and Malaysia models RV8: E, Singapore and Malaysia models RV7: Thai model RV7: Saudi Arabia model RV8: Saudi Arabia model PART No. 4-237-780-3[] 4-237-780-4[] 4-237-780-8[] 4-239-663-6[] 4-239-663-7[] · MODEL IDENTIFICATION Back Panel
PART No.
4
HCD-RV7/RV8 SECTION 2 GENERAL
LOCATION OF CONTROLS Front Panel
ALPHABETICAL ORDER A-D
ALBUM + ql ALBUM wh CD ek CD SYNC HI-DUB qg CINEMA SPACE rs DECK A A wl DECK B A qj DIMMER 9 DIRECTION q; DISC 1~3 4 DISC SKIP EX-CHANGE 5 Disc tray 3 DISPLAY 7 FM MODE qd GAME ef GAME EQ rj GAME INPUT (jacks) wg GAME MIXING es GROOVE rk IR (receptor) 2
This section is extracted from instruction manual.
R-Z
REC PAUSE/START qh REPEAT qd SPECTRUM 8 SHUTTLE qa SURROUND SPEAKER MODE e; TAPE A/B eh TUNER/BAND ej TUNER MEMORY ed VOLUME qs
K-Q
KARAOKE PON ea MD (VIDEO) eg MIC jack wd MIC LEVEL ws MOVIE EQ ra MUSIC EQ el OPEN/CLOSE Z 6 P FILE rd PHONES (jack) w; PLAY MODE ed PICTURE EFFECT rg
BUTTON DESCRIPTIONS
@/1 1 hH wf x qf X wj > qk . wk M/+ ql m/ wh v/V/b/B r;
E-J
ECHO LEVEL wa EDIT q; EFFECT ON/OFF rh ENTER rf
1
23
4
5
6
7 8
ek ej eh eg
9 0 K L M
N O
el
r;
ra
ef ed es ea e; wl wk wj wh rk
rs
qh qj qk ql
rfrd
wg
X W ws wa
w;
5
HCD-RV7/RV8
Remote Control
ALPHABETICAL ORDER A-D
ALBUM +/ ed CD rg CINEMA SPACE ws CLEAR qf CLOCK/TIMER SELECT 2 CLOCK/TIMER SET 3 D.SKIP qa DIMMER el DISPLAY ra PLAY MODE es PRESET +/ ef PREV eh REPEAT qs RETURN O eg
S-Z
SELECT qg SLEEP 1 SPECIAL MENU ek SPECTRUM r; SURROUND SPEAKER MODE e; TAPE A/B 6 TUNER/BAND rh TUNING +/ qj TV CH +/ 8 TV @/1 4 TV VOL +/ 7 TV/VIDEO 9 VOL +/ wd
+ +
1 4 7
2 5 8
3 6 9
E-M
EFFECT ON/OFF wa ENTER wk GAME rs GAME EQ wj GAME MIXING rd KARAOKE PON ql KEY CONTROL #/2 w; MD (VIDEO) rf MOVIE EQ wf MUSIC EQ wl
.
.
m
m
3
2
v
+
v
BUTTON DESCRIPTIONS
@/1 5 nN qg X qh x qk ./> ef m/M qj v/V/b/B wh
N-R
NEXT ej Numeric buttons q; ON SCREEN qd P FILE wg PICTURE EFFECT ea
Setting the clock
1 2
Turn on the system. Press CLOCK/TIMER SET on the remote.
When you set the time for the first time, proceed to step 5.
3 4 5 6 7 8
Tip
Press V or v repeatedly to select CLOCK SET. Press ENTER. Press V or v repeatedly to set the hour. Press ENTER. Press V or v repeatedly to set the minute. Press ENTER.
The clock starts functioning.
If you have made a mistake or want to change the time, start over from step 2.
Note
The clock settings are canceled when you disconnect the power cord or if a power failure occurs.
6
HCD-RV7/RV8 SECTION 3 DISASSEMBLY
· This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. TOP CASE (Page 8)
3-3. LOADING PANEL (Page 8)
3-4. CD MECHANISM DECK (CDM58E-30BD62) (Page 9)
3-5. FRONT PANEL SECTION (Page 9)
3-8. BU-30 (61) ASSY (Page 11)
3-9. DRIVER BOARD, MOTOR BOARD, SENSOR (CD) BOARD AND VIDEO BOARD (Page 11)
3-6. BACK PANEL SECTION (Page 10)
3-10.TAPE MECHANISM DECK (TCM-230AWR41CS) (Page 12)
3-7. MAIN BOARD (Page 10)
3-11.BELT (Page 12)
3-12.SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD (Page 13)
7
HCD-RV7/RV8
Note: Follow the disassembly procedure in the numerical order given. 8
3-2.
TOP CASE
4 two screws (case 3 TP2)
9 top case 7 two screws (BVTP 3 × 12)
6 side panel (L)
5 two screws (BVTP 3 × 10)
8
3 side panel (R)
4 screw (case 3TP2)
2 two screws (BVTP 3 × 10)
1 three screws (case 3 TP2)
3-3.
LOADING PANEL
3 four claws
4 loading panel
BOTTOM VIEW CD mechanism deck (CDM58E-30BD62)
2 Pull-out the disc table.
1 Turn the pulley in the direction of the arrow.
Front panel side
8
HCD-RV7/RV8
3-4.
CD MECHANISM DECK (CDM58E-30BD62)
2 connector (CN301)
5 CD mechanism deck (CDM58E-30BD62)
1 wire (flat type) (19 core) (CN201)
2 connector (CN202)
3 screw (BVTP 3 × 10)
3 screw (BVTP 3 × 10)
3-5.
FRONT PANEL SECTION
2 connector (CN783)
4 connector (CN401) 2 connector (CN781)
1 wire (flat type) (17 core) (CN304)
2 connector (CN1)
2 connector (CN2)
5 front panel section 3 four screws (BVTP 3 × 10)
9
HCD-RV7/RV8
3-6.
BACK PANEL SECTION
7 back panel section
5 connector (CN976) 5 connector (CN974) 6 two screws (BVTP 3 × 10)
4 connector (CN701) 3 sensor board 2 screw (BVTP 3 × 10) 5 connector (CN973) 1 wire (flat type) (11core) (CN702)
6 five screws (BVTP 3 × 10)
6 four screws (BVTP 3 × 10)
5 connector (CN891)
3-7.
MAIN BOARD
main board claw
4 two claws
3 connector (CN904) (HCD-RV8)
3 connector (CN903) (HCD-RV8) 5 main board
1 two screws (BVTP 3 × 10)
2 two connectors (CN502, CN503)
10
HCD-RV7/RV8
3-8.
BU-30 (61) ASSY
qd qs screw (PTPWH M2.6)
qf holder (BU) (BU-30) assy
9 0 two insulators (BU-30)
qa BU-30 (61) assy
8 screws (DIA. 12) 0 two insulators (BU-30) 6 two stoppers (BU) 5 two screws (BVTP 2.6 × 8) 4 BD board 1 wire (flat type) (28 core) (CN101) 3 Remove the four solders of sled motor and spindle motors. 7 two screws (PTPWH M2.6)
2 wire (flat type) (16 core) (CN102)
3-9.
DRIVER BOARD, MOTOR BOARD, SENSOR (CD) BOARD AND VIDEO BOARD
qg tray qf screw (PTPWH 2.6 × 8) 9 two screws (BVTP 2.6 × 8) qd motor board
qa wire (flat type) (8 core) (CN721) 0 qh screw (BVTP 2.6 × 8) 5 wire (flat type) (8 core) (CN702) 7 driver board 8 Remove the two solderings of motor. qs connector (CN722) qj sensor (CD) board
6 screw (BVTP 2.6 × 8)
4 Pull out the disc table.
3 video board
2 two screws (BVTP 2.6 × 8) 1 wire (flat type) (28 core) (CN101)
11
HCD-RV7/RV8
3-10. TAPE MECHANISM DECK (TCM-230AWR41CS)
8 tape mechanism deck (TCM-230AWR41CS) 2 five screws (BVTP 2.6 × 8)
3
2 two screws (BVTP 2.6 × 8)
7 shield plate (TC) 5 game in board 4 two screws (BVTP 2.6 × 8)
1 two knobs (mic)
6 two screws (P 2.6 × 3)
3-11. BELT
4 belt (capstan B) 3 belt (capstan C) 2 motor assy (capstan) (M901)
5 belt (FR) 4 belt (capstan B)
5 belt (FR)
1 two screws (PS 2.6 × 5)
12
HCD-RV7/RV8
3-12. SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD
2 five claws
3 SW board
1 Remove the four solders.
5 head (A) board 4 screw (PTT 2 × 4) 7 head (B) board
6 screw (PTT 2 × 4)
13
HCD-RV7/RV8 SECTION 4 TEST MODE
[GC TEST MODE]
· This mode is used to check the fluorescent indicator tube, LED, model, destination software version, volume, key and VACS level. Procedure: 1. Press three buttons x , [ENTER], and [DISC 2] simultaneously. 2. LEDs and fluorescent indicator tube are all turned on. 3. When you want to enter the software version display mode, press [DISC 1]. The model and destination are displayed. 4. Each time [DISC 1] is pressed, the display changes starting from MC version, GC version, CD version, CDDM version, CDMA version, CDMB version, BDA version, BDB version, ST version, TA version, TM version and TC version in this order, and returns to the MC version display. 5. When [DISC 3] is pressed while the version numbers are being displayed except model and destination, year, month and day of the software creation appear. When [DISC 3] is pressed again, the display returns to the software version display. When [DISC 1] is pressed while year, month and day of the software creation are being displayed, the year, month and day of creation of the software versions are displayed in the same order of version display. 6. Press [DISC 2] button, and the key check mode is activated. 7. In the key check mode, the fluorescent indicator tube displays "K0 V0". Each time a button is pressed, "K" value increases. However, once a button is pressed, it is no longer taken into account. "V" value increases like 1, 2, 3 ... if rotating [VOLUME] knob in "+" direction, or it decreases like 0, 9, 8 ... if rotating in "" direction. 8. Also when [DISC 3] is pressed after lighting of all LEDs and fluorescent indicator tubes, value of VACS level appears. 9. To release this mode, press three buttons in the same manner as step 1, or disconnect the power cord. * Tape function 1. When a tape is inserted in tape deck B and recording is started, the input source function selects VIDEO automatically. When [CD SYNC HI-DUB] button is pressed during recording in function, ALC is turned on. 2. When x button is pressed to stop recording, the tape deck B is selected and tape is rewound, tape is rewound using m button, tape is stops at around the record-starting position and playback of the recorded portion of the tape is started. If the [REC PAUSE/ START] button is pressed for a pause and pressed again to resume recording, when tape deck B is rewound, tape deck B will be rewound until the position where the pause is applied. 3. When [CD SYNC HI-DUB] button is pressed during playback of tape deck B, either normal speed or high speed can be selected by this button. * AMS Test Mode 1. Select the function "TAPE A" or "TAPE B". 2. Select the loop and relay by pressing the [DIRECTION] button. Insert a test tape AMS-110A or AMS-120 to selected tape deck. 3. Press the [SPECTRUM] button to enter the AMS test mode. 4. After a tape is rewound first, the FF AMS is checked, and the mechanism is shut off after detecting the AMS signal twice. 5. Then the REW AMS is checked and the mechanism is shut off after detecting the AMS signal twice. 6. When the check is complete, a message of either OK or NG appears. * To release MC Test mode. 1. To release this mode, press the ?/1 button. 2. The cold reset is enforced at the same time.
[COLD RESET]
· The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press three buttons x , [ENTER], and ?/1 simultaneously. 2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.
[MC TEST MODE]
· This mode is used to check operations of the respective sections of Amplifier, Tuner, and Tape. Procedure: * To enter MC Test Mode 1. Press three buttons of x , [ENTER] and [DISC 3] simultaneously. 2. The messages MUSIC, MOVIE, GAME and P FILE flash on the fluorescent indicator tube. The input FUNCTION is changed to VIDEO. * Check of Amplifier 1. When v button is pressed, GEQ increases to its maximum and a message "GEQ MAX" appears. 2. When V button is pressed, GEQ decreases to its minimum and a message "GEQ MIN" appears. 3. When b or B button is pressed, GEQ is set to flat and a message "GEQ FLAT" appears. 4. When the [VOLUME] knob is turned clockwise even slightly, the sound volume increases to its maximum and a message "VOLUME MAX" appears for two seconds, then the display returns to the original display. 5. When the [VOLUME] knob is turned counter-clockwise even slightly, the sound volume decreases to its minimum and a message "VOLUME MIN" appears for two seconds, then the display returns to the original display. * Check of clock frequency 1. To check the frequency of clock used to run the time in the unit, the clock output is available at IC501 pin el (CLOCK-OUT) on the MAIN board only during MC test mode. 2. The frequency is 32.768 kHz or so.
[VACS ON/OFF MODE]
· This mode is used to switch ON and OFF the VACS (Variable Attenuation Control System). Procedure: 1. Press ?/1 button to turn the set ON. 2. Press the [ENTER] and [GAME MIXING] buttons simultaneously. The message "VACS OFF" or "VACS ON" appears.
[TUNER STEP CHANGE] (EXCEPT Saudi Arabia model)
· A step of AM channels can be changed over between 9 kHz and 10 kHz. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function "TUNER", and press [TUNER/BAND] button to select the BAND "AM". 3. Press ?/1 button to turn the set OFF. 4. Press [ENTER] and ?/1 buttons simultaneously, and the display of fluorescent indicator tube changes to "AM 9k STEP" or "AM 10k STEP", and thus the channel step is changed over.
14
HCD-RV7/RV8
[CD SERVICE MODE]
· This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the optical pick-up. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function "CD". 3. Press three buttons x , [ENTER] , and [OPEN/CLOSE] simultaneously. 4. The CD service mode is selected. 5. With the CD in stop status, press M + button to move the optical pick-up to outside track, or press m button to inside track. 6. To release this mode, press the ?/1 button.
Aging mode sequence (CD section) :
Start (from disc 1)
Disc chucking
TOC read
Play first track for 2 seconds
[AGING MODE]
This mode can be used for operation check of CD section and tape deck section. CD section and tape deck section work in parallel. · If an error occurred: The aging operation stops only an error occurred sections and display then status. · If no error occurs: The aging operation continues repeatedly. Procedure: 1. Press the ?/1 button to turn the power ON, and press the [CD] button to select the function "CD". 2. Set discs on all trays, and set tapes into the decks A and B respectively. 3. Press the [PLAY MODE] button to set the "ALL DISCS" mode, and press the [REPEAT] button to "REPEAT" off. 4. Press three buttons of x , [ENTER], and [EX-CHANGE/DISC SKIP] simultaneously. 5. Aging operations of CD and tape are started at the same time. 6. To release this mode, press the ?/1 button or disconnect the power code to turn the power OFF. 1. Display at the Aging Mode Display operating state of CD section and tape deck section alternately. If an error occurred, stop display which that section. 2. CD Section The sequence during the aging mode is following as below. Display at the aging mode is the same as the normal operation.
Play last track for 2 seconds
EX-change open/close
Open the disc tray
Disc skip
Close the tray
Change the next disc.
· Display at an error occurred (Error display mode) Procedure: 1. Press three buttons of x , [ENTER], and [DISC 1] simultaneously to enter the error display mode. 2. It displays of total error. 3. Each time the m or M + button is pressed, display change as below. 4. To clear the error record, operate the cold reset. (Refer to the "MC COLD RESET") 5. To release this mode, press the ?/1 button or disconnect the power plug to turn the power OFF.
Display of total error
m Button M + Button
Display of Mechanical errors
m Button M + Button
Display of no disc errors
15
HCD-RV7/RV8
1) Display of total error
Display
3. Tape Deck Section The sequence during the aging mode is following as below. If an error occurred, stop display that step. Aging mode sequence (Tape deck section) :
EMC**EDC**
EMC**: The number of mechanical error. EDC**: The number of no disc error after chucking the disc. 2) Display of mechanical errors
Display
Rewind the tape A and B "TAPE A AG-1" Shut off FWD play the tape A "TAPE A AG-2" 2 minutes Fast forward the tape A "TAPE A AG-3" Shut off or 20 seconds REV play the tape A "TAPE A AG-4" 2 minutes Rewind the tape A "TAPE A AG-5" Shut off FWD play the tape B "TAPE B AG-2" 2 minutes Fast forward the tape B "TAPE B AG-3" Shut off or 20 seconds
M*$$%%&&##00
M*: The number of mechanical error ("00" is latest one) (Press the . or > button to changes next error display) $$: Not used %%: Loading error (Second figure is not used) D: The error in the midst of close at the except mechanical trouble. E: The error in the midst of open at the except mechanical trouble. C: The error in the midst of chucking up at the except mechanical trouble. F: The error in the midst of chucking down at the except mechanical trouble. &&: Loading error 01: The error in the midst of chucking up. 02: The error in the midst of chucking down. 03: Time-out of EX-open. 05: Time-out of EX-close. ##: Not used 3) Display of no disc errors
Display
D*$$%%&&##00
D*: The number of mechanical error("00" is latest one) (Press the . or > button to changes next error display) $$: Error type 01: Focus error 02: GFS error 03: Set up error %%: Not used &&: 00: No disc judgment without chucking retry. 01: No disc judgment after chucking retry. ##: The state when judged no disc error 01: Stop 02: Set up 03: TOC read 04: Access 05: Play 06: Pause 07: Manual search (Play) 08: Manual search (Pause)
REV play the tape B "TAPE B AG-4" 2 minutes Rewind the tape B "TAPE B AG-5" Shut off
Note: "TAPE * AG-*" is display of each step.
[CD REPEAT 5 LIMIT OFF MODE]
Number of repeat for CD playback is 5 times when the repeat mode is "REPEAT". This mode enables CD to repeat playback for limitless times. Procedure: 1. Press the ?/1 button to turn the power on, and press the [CD] button to select the function "CD". 2. Press three buttons of x , [REPEAT], and [CD] simultaneously to enter the CD repeat 5 limit off mode and display "REPEAT OFF". 3. To release this mode, operate the cold reset. (Refer to the "MC COLD RESET")
16
HCD-RV7/RV8
[CD SHIP MODE (MEMORY CLEAR) ]
· This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Set to the standby state. 2. Press three buttons x , [ENTER] and [GAME] simultaneously. 3. After the "STANDBY" display blinks, a message "LOCK" is displayed on the fluorescent indicator tube, and the CD ship mode is set.
[CD SHIP MODE (NO MEMORY CLEAR) ]
· This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Set to the standby state. 2. Press the [CD] and ?/1 buttons simultaneously. 3. After the "STANDBY" display blinks, a message "LOCK" is displayed on the fluorescent indicator tube, and the CD ship mode is set.
[VCD COLOR SYSTEM MODE ]
· The color system can be changed over PAL, AUTO or NTSC. Procedure: 1. Set to the standby state. 2. Press the [MUSIC EQ] and ?/1 buttons simultaneously to change the color system to PAL, and a message "COLOR PAL" is displayed on the fluorescent indicator tube. 3. Press the [MOVIE EQ] and ?/1 buttons simultaneously to change the color system to AUTO, and a message "COLOR AUTO" is displayed on the fluorescent indicator tube. 4. Press the [GAME EQ] and ?/1 buttons simultaneously to change the color system to NTSC, and a message "COLOR NTSC" is displayed on the fluorescent indicator tube.
[CD TRAY LOCK MODE ]
· This mode is used to lock the CD tray of display set in the shop to prevent demo discs being stolen. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function "CD", then press the x and [OPEN/CLOSE] buttons simultaneously for five seconds. 3. The message "LOCKED" is displayed on the fluorescent indicator tube, and the tray is locked. 4. To release from this mode, press the x and [OPEN/CLOSE] buttons simultaneously for five seconds again. 5. The message "UNLOCKED" is displayed on the fluorescent indicator tube, and the tray is unlocked.
17
HCD-RV7/RV8 SECTION 5 MECHANICAL ADJUSTMENTS
PRECAUTION 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. TORQUE MEASUREMENT
Mode Torque meter Meter reading
SECTION 6 ELECTRICAL ADJUSTMENTS
DECK SECTION
0 dB=0.775 V
FWD
CQ-102C
FWD back tension REV
CQ-102C
CQ-102RC
REV back tension FF/REW
CQ-102RC
CQ-201B
FWD tension
CQ-403A
REV tension
CQ-403R
3.06 N · m to 6.96 N · m 31 to 71 g · cm (0.43 0.98 oz · inch) 0.19 N · m to 0.58 N · m 2 to 6 g · cm (0.02 0.08 oz · inch) 3.06 N · m to 6.96 N · m 31 to 71 g · cm (0.43 0.98 oz · inch) 0.19 N · m to 0.58 N · m 2 to 6 g · cm (0.02 0.08 oz · inch) 6.96 N · m to 14.02 N · m 71 to 143 g · cm (0.98 1.99 oz · inch) 9.80 N · m 100 g or more (3.53 oz or more) 9.80 N · m 100 g or more (3.53 oz or more)
1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and RCH. 7. Switches and controls should be set as follows unless otherwise specified. · Test Tape Tape P-4-A100 WS-48B Signal 10 kHz, 10 dB 3 kHz, 0 dB Used for Azimuth Adjustment Tape Speed Adjustment
RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT DECK A DECK B
Note: Perform this adjustments for both decks
Procedure: 1. Mode: Playback
test tape P-4-A100 (10 kHz, 10 dB) MAIN board CN301 Pin 1 (L-CH) Pin 3 (R-CH) level meter set MAIN board CN301 Pin 2 (GND) +
18
HCD-RV7/RV8
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
TAPE SPEED ADJUSTMENT
DECK B
Note: Start the Tape Speed adjustment as below after setting to the test mode. In the test mode, the tape speed is high during pressing the [CD SYNC HI-DUB] button.
L-CH peak Output level
within 1dB within 1dB
Procedure: 1. Press ?/1 button to turn the set ON. 2. Press three buttons x , [ENTER] and [DISC 3] simultaneously. To release from the test mode, press the ?/1 button. Mode: Playback
test tape WS-48B (3 kHz, 0 dB) MAIN board CN301 Pin 1 (L-CH) frequency counter Pin 3 (R-CH) + set MAIN board CN301 Pin 2 (GND)
Screw position
R-CH peak L-CH peak R-CH peak
Screw position
3. Mode: Playback
test tape P-4-A100 (10 kHz, 10 dB) L-CH MAIN board CN301 set R-CH pin 3 waveform of oscilloscope
oscilloscope pin 1 pin 2 L R V H
1. Insert the WS-48B into the deck B. 2. Press the hH button on the deck B. 3. Press the [CD SYNC HI-DUB] button in playback mode. Then at HIGH speed mode. 4. Adjust RV1001 on the SW board so that frequency counter reads 6,000 ± 180 Hz. 5. Press the [CD SYNC HI-DUB] button. Then back to NORMAL speed mode. 6. Adjust RV1002 on the SW board so that frequency counter reads 3,000 ± 90 Hz. Adjustment Location: SW board Sample Value of Wow and Flutter: 0.3% or less W. RMS (JIS) (WS-48B)
in phase 45 ° good
90 ° 135 ° 180 ° wrong
4. After the adjustments, apply suitable locking compound to the pats adjusted. Adjustment Location: Playback Head (Deck A). Record/Playback/Erase Head (Deck B).
forward
reverse
19
HCD-RV7/RV8
REC BIAS ADJUSTMENT DECK B
Procedure: In the MC test mode, the "REC memory mode" is convenient for this adjustment. In the "REC memory mode" , when the REC starts the input signal FUNCTION is switched to VIDEO automatically. When the REC stops, the tape returns near to the recording start position. 1. Press MD (VIDEO) button to select VIDEO. (This step is not necessary if the above test mode has already been set) 2. Insert a tape into deck B. 3. After press [REC PAUSE/START] button, press [REC PAUSE/ START] button, then recording start. 4. Mode: Record
MAIN board MD/VIDEO (AUDIO) IN (J750) 1) 315 Hz 50 mV (23.8 dB) 2) 10 kHz
attenuator
4. Mode: Record
MAIN board MD/VIDEO (AUDIO) IN (J750) 315 Hz, 50 mV (23.8 dB) 600 attenuator
set
AF OSC
blank tape CS-123
5. Mode: Playback
MAIN board CN301 Pin 1 (L-CH) Pin 3 (R-CH) set
recorded portion
level meter +
AF OSC
600
set
blank tape CN-123
MAIN board CN301 Pin 2 (GND)
5. Mode: Playback
MAIN board CN301 Pin 1 (L-CH) Pin 3 (R-CH) set
recorded portion
level meter +
6. Confirm the play back signal recorded in step 3 becomes adjustable level as follows. If these levels are not adjustable level, adjust the RV301 (LCH) and RV351 (R-CH) on the MAIN board to repeat steps 4 and 5. Adjustable level: CN301 PB level: 47.2 to 53.0 mV (24.3 to 23.3 dB) Adjustment Location: MAIN board
SW BOARD (Component Side) TAPE SPEED ADJUSTMENT
MAIN board CN301 Pin 2 (GND)
(NORMAL) (HIGH) RV1002 RV1001 CN1001
6. Confirm the playback signal recorded in step 3 becomes adjustable level as follows. If these levels are not adjustable level, adjust the RV304 (LCH) and RV354 (R-CH) on the MAIN board to repeat steps 4 and 5. Adjustable level: Playback output of 315 Hz to playback output of 10 kHz: ±1.0 dB Adjustment Location: MAIN board
MAIN BOARD (Component Side)
REC LEVEL ADJUSTMENT DECK B
Procedure: In the MC test mode, the "REC memory mode" is convenient for this adjustment. In the "REC memory mode" , when the REC starts the input signal FUNCTION is switched to VIDEO automatically. When the REC stops, the tape returns near to the recording start position. 1. Press MD (VIDEO) button to select VIDEO. (This step is not necessary if the above test mode has already been set) 2. Insert a tape into deck B. 3. After press [REC PAUSE/START] button, press [REC PAUSE/ START] button, then recording start.
REC LEVEL ADJUSTMENT CN301 3 1 (R-CH) RV351 RV304 (L-CH) (L-CH) RV301 RV354 (R-CH)
REC BIAS ADJUSTMENT
20
HCD-RV7/RV8
CD SECTION
Note: 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use LUV-P01 (Part No. 4-999-032-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
Note: Clear RF signal waveform means that the shape " " can be clearly distinguished at the center of the waveform.
VIDEO SECTION VIDEO LEVEL ADJUSTMENT (AUDIO LEVEL/VIDEO CLOCK/AUDIO SERVO CLOCK CHECK)
oscilloscope
Connecting and Adjustment Location:
VIDEO BOARD (Component Side)
RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500ns
S-CURVE CHECK
oscilloscope BD board TP68 (FE) TP73 (DVC) +
level : 0.75 ±0.1Vp-p (RFDC) 1.05 ±0.3Vp-p (RFAC)
VIDEO board TP308 (V-OUT) +
TP308 (V-OUT)
TRAVERSE LEVEL CHECK
oscilloscope BD board TP70 (TE) TP73 (DVC) +
frequency counter +
TP70 (54 MHz)
VIDEO board TP415 (L-OUT) TP413 (R-OUT)
level meter +
Procedure : 1. Connect an oscilloscope to TP68 (FE) and TP73 (DVC) on the BD board. 2. Turn the power ON. 3. Load a disc (LUV-P01) and actuate the focus search. (In consequence of open and close the disc tray, actuate the focus search) 4. Confirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2 ± 0.5 Vp-p.
S-curve waveform symmetry
TP182 (4.2336 MHz)
VIDEO board TP70 (54 MHz) TP182 (4.2336 MHz)
Procedure : 1. Connect an oscilloscope to TP70 (TE) and TP73 (DVC) on the BD board. 2. Turn the power ON. 3. Load a disc (LUV-P01) and playback the number nine track. 4. Press the hH button. (Becomes the 1 track jump mode.) 5. Confirm that the level B and A (DC voltage) on the oscilloscope waveform.
1 track jump waveform center of waveform B A (DC voltage) DVC level=1.2 ±0.55Vp-p symmetry
TP415 (L-OUT)
TP413 (R-OUT)
RV501 Video Level Adjustment
A within 2 ±0.5Vp-p B
Note: · Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. · Take sweep time as long as possible and light up the brightness to obtain best waveform.
Connecting Location:
BD BOARD (Conductor Side)
Procedure : 1. Connect an oscilloscope to TP308 (V-OUT) on the VIDEO board. 2. Connect a level meter to TP415 (L-OUT) and TP413 (R-OUT) on the VIDEO board. 3. Connect a frequency counter to TP70 (54 MHz) and TP182 (4.2336 MHz) on the VIDEO board. 3. Turn the power ON. 4. Set a test disc (HLV-402 (Part No. 8-909-870-00)) 5. Press three buttons x , [ENTER] , and [OPEN/CLOSE] simultaneously. 6. The message "MPEG AV TEST" is displayed on the fluorescent indicator tube. Color bar signal outputs and sine-wave (1 kHz 0dB) appears. 7. Adjust the RV501 on the VIDEO board for 0.714 ± 0.05 Vp-p.
Note: TP308 (V-OUT) on the VIDEO board must be teminated by 75 .
RF LEVEL CHECK
oscilloscope BD board TP71 (RFDC) TP72 (RFAC) TP73 (DVC) +
0.714 ± 0.05 Vp-p
Procedure : 1. Connect an oscilloscope CH1 to TP71 (RFDC), CH2 to TP72 (RFAC) and TP73 (DVC) on the BD board. 2. Turn the power ON. 3. Load a disc (LUV-P01) and playback the number nine track. 4. Confirm that oscilloscope waveform is clear and check if RF signal level is correct or not.
TP70 (TE) TP72 (RFAC)
TP68 (FE) TP71 (RFDC) TP73 (DVC)
8. Confirm that the value of level meter is 2.5 ± 2.0 dBs. (If audio output disappear, press the [PLAY MODE] button twice) 9. Confirm that the value of frequency counter is 54 MHz ± 400 Hz. 10. Confirm that the value of frequency counter is 4,2336 MHz. 11. Change disc to a MP3 test disc (MP3 1kHz 0dB sine-wave is recorded) 12. Confirm that the value of level meter is 2.4 ± 2.0 dBs.
21
21
HCD-RV7/RV8 SECTION 7 DIAGRAMS
7-1. BLOCK DIAGRAM CD SERVO Section
FREQUENCY SELECT SWITCH Q102 FILTER RF AMP, FOCUS/TRACKING ERROR AMP IC103 6 7 8 9 DETECTOR RF DC AMP 11 10 F E F I-V AMP E I-V AMP TRACKING ERROR AMP TE A B C D FOCUS ERROR AMP FE FEI RFDCO RFDCI 16 17 28 29 D/A3 D/A1 DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR IC505 (1/2) 164 FE AC SUM EQ IN CONT
A
(Page 23)
26
168
170 171
169
RFC
FILO
PCO
CLTV
FILI
RF SUMMING AMP
4
3
RFAC VCA
EQ
RFAC
XTSL 189 PCMD BCK LRCK C2PO DATA CLOK XLAT SENS SCOR SQSO L SQCK L SCLK GFS L FOK L CDXRST 91 93 88 124 102 111 109 113 126 96 98 114 121 131 105 DATA BCK LRCK C2PO DATA CLOK XLAT SENS SCOR SQSO SQCK SCLK GFS FOK XRST
15
173 RFAC
DATA, BCK, LRCK, C2PO
B
(Page 23)
DATA, CLOK, XLAT, SENS, SCOR, SQSO, SQCK, SCLK, GFS, FOK, XRST
C
(Page 23)
160 RFDC
· R-ch is omitted due to same as L-ch. · SIGNAL PATH : CD PLAY
18
162 TE 163 SE
SRDR
TRDR
FRDR
SFDR
TFDR
SSTP
XTAO
FFDR
MDP
OPTICAL PICK-UP BLOCK (A-MAX. 3) LASER DIODE AUTOMATIC POWER CONTROL Q101 LD SW 12 D/A4
133 137 138
140 141
142 143
135
150
149
1
APC LD AMP
PD
X501 33.8688MHz 2 DISC TRAY STATUS SENSOR IC711 S711 OPTICAL PICK-UP UP/DOWN DETECT
PD
LD
D/A2
XTAI
TBL-SENS 49
FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE IC102 VO4+ VO4 MOTOR DRIVE IN4 23
BU UP/DOWN-SW 48
M101 (SPINDLE)
M
5 10
OPEN-SW 46 OPEN CLOSE CLOSE-SW 47 S701 DISC TRAY OPEN/CLOSE DETECT
M102 (SLED)
M
1 2
VO3+ VO3 MOTOR DRIVE
IN3+ IN3
27 26 SYSTEM CONTROLLER (CD MECHANISM CONTROL) IC501 (1/4) TURN MOTOR DRIVER IC701 7 9 FIN RIN MOTOR DRIVE OUT2 2 OUT1 4 M721 (TURN)
SYSRST
2-AXIS DEVICE
56 55
VO2+ VO2 COIL DRIVE
IN2+ IN2
LOAD-OUT 45 LOAD-IN 44
M
32 31
(FOCUS) (TRACKING)
43
47 52
VO1+ VO1
IN1+ COIL DRIVE IN1
35 34
D/A1 D/A2 D/A3 D/A4 SHARPNESS HUE
STBY
3 5 6 9 13 2
AO3 AO4 AO5 AO6 AO1 AO2
D/A CONVERTER IC506
DI 12 CLK 11 LD 10
DATA CLK LD
DATA, CLK, LD
D
(Page 23)
8 (LIMIT) ON : When the optical pick-up is inner position
RST
4 SYSRST SHARPNESS, HUE
E F
(Page 23) (Page 23)
22
22
HCD-RV7/RV8
7-2.
(Page 22)
BLOCK DIAGRAM AUDIO/VIDEO CD Section
A B
CONT DATA, BCK, LRCK, C2PO 24 GPIO9 DATA BCK LRCK C2PO DATA CLOK XLAT SENS SCOR SQSO SQCK SCLK GFS FOK XRST CD L-CH
(Page 22)
(Page 22)
C
DATA, CLOK, XLAT, SENS, SCOR, SQSO, SQCK, SCLK, GFS, FOK, XRST
90 92 87 123 103 110 108 112 125 95 99 115 120 132 106
L CDDATA L CDBCK L CDLRCK L CDC2PO L DDAT L DCLK L XLAT L SENS L SCOR L SQSO SQCK SCLK L GFS FOK XRST
AUDDTO0 201 AUDBCK 203 AUDLRCK 204 AUDXCLKO 205 GPIO14 GPIO13 GPIO11 GPIO12 30 29 26 28
2 1 3
DATA BCK LRCK DIGITAL FILTER, D/A CONVERTER IC504
VOUTL VOUTR
7 8
LOW-PASS FILER IC102
G
(Page 25)
R-CH
16 MLCK 13 DATA 14 CLK 15 LAT
· R-ch is omitted due to same as L-ch. · SIGNAL PATH
VCC
VDD
MPEG VIDEO/AUDIO DECODER, VIDEO SIGNAL ENCODER IC505 (2/2)
: CD PLAY (AUDIO) : CD PLAY (VIDEO) : GAME INPUT (VIDEO)
CD D+5V, CD A+5V DATA, CLK, LD
RV501 VRF 3 VIDEO LEVEL
5 +3.3V REGULATOR Q581
6
DATA CLK LD
CPSIG CSIG
6 7
D
(Page 22)
DRADR0 DRADR10 34 37, 39 45
DRDAT0 DRDAT15 49 56, 59 66
GPIO0 GPIO1 GPIO2 GPIO5 GPIO4 GPIO3
CLKB
CLKA
(Page 22)
E
SYSRST
81 SYSRST
NVOEL DRWEL DRRAS DRCAS DRCK DRBS DRDQM0 DRDQM1
207
206
74 73 72 68 70 76 77 78
13 14 15 19 18 16 SYNC BUFFER Q301
Y AMP IC304 Y SYNC BUFFER Q302
D0 D15
A0 A10
X502 27MHz
B.P.F.
10 VIN VOUT 1 CONT IN 5
+
SDO SDI SCK SCS SOK SRQ
ADDRESS BUS C AMP IC303 B.P.F. 1 VIN
SHARPNESS
DATA BUS
A0 A10
D0 D15
D8 D15
A0 A10
VOUT 6
D0 D7
23 26, 29 34, 22 A0 A10 D-RAM IC507
2, 4, 5, 7, 8, 10, 11, 13, 42, 44, 45, 47, 48, 50, 51, 53
5 12 5, 27, 26, 31 A0 A9, A18 PROGRAM ROM IC508 13 15, 17 21 DQ0 DQ7 23, 25, 4, 28, 29, 3, 2, 30 A10 A17 SYNC SEPARATOR IC301 C SYNC BUFFER IC302
TINT
8 HUE SHARPNESS, HUE
UDQM LDQM BA0 CLK CAS RAS WE
DQ0 DQ15
BGP
F
39 15 20 38 17 18 16
24 VIDEO AMP IC307
OE
(Page 22)
VIDEO SELECT SWITCH, VIDEO AMP IC781 J401 VIDEO OUT 3 IN OUT 6 OUTSAG 5 1 3 VIN1 VIN2 VOUT 7
8
BUF IN
BUF 1 OUT
STBY 2 J601(1/2) GAME INPUT VIDEO VIDEO MUTING CONTROL SWITCH Q370
SW1
2
V SW
H
(Page 25)
V MUTE SDO, SDI, SCK, SCS, SOK, SRQ
J K
(Page 25)
(Page 25)
23
23
HCD-RV7/RV8
7-3.
BLOCK DIAGRAM TUNER/TAPE DECK Section
ANTENNA FM ANT TUNER UNIT L-CH R-CH ST-DOUT ST-DIN ST-CLK ST-CE ST-MUTE TUNED STEREO R-CH DI DO CLK CE MUTING TUNED STEREO TUNER L-CH
FM 75 ANT GND AM ANT AM ANT GND
L
(Page 25)
DECK A/B SELECT SWITCH, PB EQ AMP IC301 (1/2)
MUTE L-CH HP901 (PB) R-CH R-CH 32 34 AIN1 BIN1
REC MUTE ON/OFF A/B NORMAL/HIGH SPEED
PB-OUT1 EQOUT1 28 27 TAI1
26
TAPE L-CH
M
(Page 25)
MUTE ON/OFF
R-CH
LOW-PASS FILTER IC303 MUTING Q306 MUTING CONTROL SWITCH Q389
BUFFER Q390, 398, 399
+
L-CH REC/PB SWITCHING IC302 R-CH
· R-ch is omitted due to same as L-ch. · SIGNAL PATH : TUNER (FM/AM) : TAPE PLAY (DECK A) : TAPE PLAY (DECK B) : REC
R-CH
R-CH
3 R-CH
1
15 13 12
14
4 2 HRPE901 (REC/PB/ERASE) BIAS TRAP RV304 REC BIAS (L) (DECK B) REC/PB SWITCHING Q304, 305 R-CH RV354 REC BIAS (R) (DECK B) 21 REC EQ AMP, ALC IC301 (2/2) RECOUT1 REC L-CH
REC MUTE A/B NOR/HIGH
EQ
REC-IN1
24 RV301 23 REC LEVEL (L) (DECK B)
N
(Page 25)
ALC ON/OFF
R-CH
ALC
ALC1
R-CH
BIAS OSC T301
11 REC BIAS SWITCH Q301, 307, 310 TC +10V
DI DO CLK CE MUTING TUNED STEREO REC MUTE A/B NOR/HIGH
BIAS OSC Q302, 303 69
TC-RELAY
25 23 27 22 21 3 2
ST-DIN ST-DOUT ST-CLK ST-CE ST-MUTE TUNED STEREO
68
ALC
61 67 66
REC-MUTE PB-A/B EQ-H/N
58
TC-MUTE
53
AMS-IN A-TRIG
65 BIAS
M901 (CAPSTAN)
M
CAPSTAN MOTOR DRIVE Q396, 397 Q395
55 CAPM-CNT1
SYSTEM CONTROLLER (CD MECHANISM CONTROL) IC501 (2/4)
A-SHUT A-PLAY B-PLAY A-HALF B-HALF B-SHUT B-TRIG
CAPSTAN MOTOR CONTROL SWITCH Q1001 RV1002 TAPE SPEED (NORMAL) RV1001 TAPE SPEED (HIGH)
54 CAPM-H/L
56
57
70
91
89
90
51
52
D +3.3V D +3.3V S1001 (DECK A PLAY) S1002 (DECK B PLAY) S1003 (DECK A HALF) D +3.3V S1009 (DECK B REC) S1006 (DECK B HALF) S1005 (DECK A REC) ROTATION DETECT SENSOR (DECK A) IC1001 ROTATION DETECT SENSOR (DECK B) IC1002
TRIGGER PLUNGER DRIVE (DECK A) Q393, 394 PM901 TRIGGER PLUNGER (DECK A)
TRIGGER PLUNGER DRIVE (DECK B) Q391, 392 PM902 TRIGGER PLUNGER (DECK B)
24
24
HCD-RV7/RV8
7-4. BLOCK DIAGRAM MAIN Section
SURROUND SIGNAL PROCESSOR IC181 10 L-OUT L-IN 7 3 AUDO OUT ON/OFF SWITCH IC430 4 R-CH 5
J430 L AUDIO OUT R
SUR1 SUR2 SUR3
BP/SR CONT2 CONT3
1 2 3
(Page 24)
N
REC L-CH J750 L 42 8 INPUT SELECT SWITCH, TONE CONTROL, ELECTRICAL VOLUME IC102 FEED BACK SWITCH Q101 16 17
R-CH D841
AUDIO OUT ON/OFF SWITCH Q430
J631 PHONES HEADPHONE MUTING Q812, 862
RECB1
BB A1
R
R-CH
+
R-CH
R-CH
+
BB B1
SUR1
MD/VIDEO (AUDIO) IN
MUTING CONTROL SWITCH Q861 T501
+
(Page 23)
G L M
CD L-CH IND1 6 INB1 INPUT 4 INC1 SELECT 5 INA1 SWITCH 3 INEX1 TOUT1 SOUND CONTROL CIRCUIT VOLIN1 VOLUME 15 CONTROL OUT1 2 18 POWER AMP IC501
(Page 24)
TUNER L-CH
14
1
(Page 24)
TAPE L-CH 7 J601 (2/2)
R-CH R-CH
D507
CPU INTERFACE
MUTING Q103 R-CH
GAME INPUT AUDIO
SAOUT
SWOUT
MIC
DATA CLOCK
L R R-CH RV721 ECHO LEVEL DIGITAL ECHO IC721
STANDBY SWITCH Q503, 504, 581
D511
+
R-CH
+ + + +
RY502
L FRONT SPEAKER IMPEDANCE USE 616 R
+
2
19
24
21 22
OVER LOAD DETECT Q501, 551
L
+
DC DETECT SWITCH Q507, 508 RY501
R
SURROUND SPEAKER IMPEDANCE USE 24
81 82
GEQ DATA
GEQ CLK
MIC AMP IC722 (1/2) J721 MIC RV722 MIC LEVEL
MIC AMP IC722 (2/2)
SUR1 SUR2 SUR3
SUR1 5 SUR2 6 SUR3 7
+
D502
OVER LOAD DETECT SWITCH Q509
OVER LOAD DETECT SWITCH Q510
OVER LOAD DETECT SWITCH Q511
FRONT SPEAKER PROTECT RELAY DRIVE Q512
AUDIO-OUT 77 ON/OFF PROTECTOR 88 FRONT-RELAY 87 SYSTEM CONTROLLER (CD MECHANISM CONTROL) IC501 (3/4) SYSOUT SYSIN SYSCLK STK-MUTE 83 SYSCS SYSOK SYSRQ HP MUTE 78 HP-DETECT 79 LINK-RELAY 86 SW RELAY 97
PROTECT SWITCH Q502
SURROUND SPEAKER PROTECT RELAY DRIVE Q513 1 TM801
MIC CONTROL Q721 SDO SDI SCK SCS SOK SRQ
+
2 TEMPERATURE DETECT SWITCH Q505, 506 FAN MOTOR ON SWITCH Q831 TH701 FAN MOTOR DRIVE Q891, 892
M891 (FAN) RY801
SUB WOOFER OUT IMPEDANCE USE 8
(Page 26)
P
SPEANA
A +10V
(Page 23) (Page 23) (Page 23)
K J H
SDO, SDI, SCK, SCS, SOK, SRQ V MUTE V SW CN101 SYSTEM CONTROL (TO SS-WGV8) 1 AD-KEY 7
35 36 37 19 32 40
M
OVER LOAD DETECT SWITCH Q825 SUB WOOFER PROTECT RELAY DRIVE Q824
33 VIDEO MUTE VIDEO-OUT 76 GAME/VCD
94 SW-AD-KEY 59 SW-ON-LED 5 71 SW-LINK-LED 4 SW-MATRIX72 SURR-1-LED SW-MATRIX60 SURR-2-LED LINE-MUTE 80
MUTING CONTROL SWITCH Q504, 505
SW-SOLID-LED SW-LINK-LED SW-MTRX-SURR-LED 6 SW-WIDE-LED
R-ch is omitted due to same as L-ch. SIGNAL PATH : TUNER (FM/AM) : TAPE PLAY : REC : CD PLAY : MD/VIDEO (AUDIO) IN : GAME INPUT (AUDIO) : AUDIO OUT : MIC INPUT
BUFFER IC901 (2/2)
LOW-PASS FILTER IC901 (1/2)
2
4
7
VOLUME CONTROL
9
LINE AMP IC903 (1/2)
FILTER AMP IC903 (2/2)
SUB WOOFER AMP IC502 (1/2)
SUB WOOFER AMP IC502 (2/2)
LINE AMP, ELECTRICAL VOLUME IC902 2 VOLUME (RV8)
8
AGC Q905
MUTING Q999
STANDBY SWITCH Q1001-1003
OVER LOAD DETECT Q1004, 1054
25
25
HCD-RV7/RV8
7-5.
BLOCK DIAGRAM DISPLAY/KEY CONTROL/POWER SUPPLY Section
1 10, 12 22, 24 41, 43, 44
P1 P41
52 59, 74
FL601 FLUORESCENT INDICATOR TUBE
LED-TAPE, LED-TUNER, LED-MD-VIDEO, LED-CD, LED-GAME, LED-DISC1, LED-DISC2, LED-DISC3, LED-REC
1G 15G
100 86
LED DRIVE Q601 605, Q791 793, 795
D604 608, D791 793, 795
KEY0 KEY2 64 66
S751 792
BAND-PASS FILTER IC602
FLUORESCENT INDICATOR TUBE DRIVER, KEY CONTROL IC601 +VL
T910 MAIN POWER TRANSFORMER RECT D541
BPF0 BPF5
(Page 25)
P X
4 LINE IN 6 REC IN
67 72
SPEANA
F01 F06 17 12
VL
+VH VH
L+R 11
73 ALL-BAND
RECT D543
VOLUME
ROTARY ENCODER S748
VG 80 VOLUME-A 79 VOLUME-B SYSTEM CONTROLLER (CD MECHANISM CONTROL) IC501 (4/4)
33V REGULATOR Q941
RECT D977
83 X1 X601 4MHz 82 X0
I2C-DATA 60 I2C-CLOCK 61 RESET 77
30 IIC-DATA 29 IIC-CLK 41 GC-RESET
TO FLUORESCENT INDICATOR TUBE FL601 +4.5V +4.5V REGULATOR Q201 +2.5V REGULATOR IC201 +3.3V REGULATOR IC202 CD D+5V CD A+5V SYSPWR 38 +4V REGULATOR IC951 D503 A +10V TC +10V D920 922 M +7V +9V REGULATOR IC961 +10V REGULATOR IC101 RECT D914 917
VF1 VF2
M +9V +2.5V
RECT D906 909
D D +3.3V D794 LED DRIVE Q794 75 STBY-LED
+5V REGULATOR IC911
B+ SWITCH Q911, 912 (RV7: Thai)
S749
D +4V 74 POWER-KEY D501 73 DISPLAY-KEY S750 DISPLAY STBY-RELAY 84 REMOTE CONTROL RECEIVER IC603 4 SIRCS D +3.3V D502 D504
RECT D918, 919, 923, 924 VOLTAGE SELECTOR S901 (EXCEPT RV7: Thai) POWER ON/OFF RELAY DRIVE Q971 RY971
T972 SUB POWER TRANSFORMER 15 X-IN X502 16MHz 13 X-OUT RESET 12 10 XC-IN RESET SWITCH Q601 RESET SIGNAL GENERATOR IC601 EVER +4V +4V REGULATOR IC971 RECT D972 975 (AC IN)
D505
X501 32.768kHz 11 XC-OUT
AC-CUT 20
26
26
HCD-RV7/RV8
7-6.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. · · 2 : nonflammable resistor. · 5 : fusible resistor. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · · · · A : B+ Line. B : B Line. H : adjustment for repair. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : TUNER (FM/AM) E : TAPE PLAY (DECK A) d : TAPE PLAY (DECK B) G : REC J : CD PLAY (AUDIO) L : CD PLAY (VIDEO) q : MD/VIDEO (AUDIO) IN j : GAME INPUT (AUDIO) k : GAME INPUT (VIDEO) f : AUDIO OUT N : MIC INPUT Abbreviation EA : Saudi Arabia model MY : Malaysia model SP : Singapore model TH : Thai model
· Circuit Boards Location
VIDEO board SUB-TRANS board MAIN TRANS board SENSOR board CD OPEN board SUB WOOFER board (HCD-RV8)
Note on Printed Wiring Board: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. · : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
CD SWITCH board TUNER PACK PANEL board
· VIDEO board is multi-layer printed board. However, the patterns of intermediate-layer have not been included in diagram. · Indication of transistor.
C Q B E These are omitted.
MAIN board PAD SWITCH board
·
Q B C E These are omitted.
· ·
POWER board
VOL board GAME IN board
Q B C E These are omitted.
MOTOR board SENSOR (CD) board BD board
·
DRIVER board
SW board
HEAD (A) board
HEAD (B) board
27
27
HCD-RV7/RV8
7-7.
PRINTED WIRING BOARD BD Board
· See page 27 for Circuit Boards Location.
BD BOARD (COMPONENT SIDE)
BD BOARD
(CONDUCTOR SIDE)
(SPINDLE)
M
IC102
E
D101
TP70 (TE)
TP68 (FE) TP72 (RFAC)
30
16
TP71 (RFDC)
A
1
IC103
15
TP73 (DVC)
VIDEO BOARD CN101 (Page 32)
E
11 1-684-174(11)
M
OPTICAL PICK-UP BLOCK (A-MAX. 3)
(SLED)
11 1-684-174(11)
28
28
HCD-RV7/RV8
7-8.
SCHEMATIC DIAGRAM BD Board
· See page 35 for Waveforms.
· See page 54 for IC Block Diagram.
TP27
C115 47 6.3V R104 15k R227 100k C107 33p R120 120k
C117 0.1
C120 47 4V
C109 0.1
C112 47 4V CC1 TP49 AA5 TP26
CN102 16P I1-6 VC CC2 TP25 I5-10 VCC
AA1 AA9 AA3
FE FEI TE C103 470p C101 470p R102 15k R105 1k TE_BAL CE C102 0.1 C104 0.0033 R112 0 CEI VCC AA10 D101 1SS355 R103 100k R111 120k R114 47k RFG BST Q102 UN2111-TX FREQUENCY (CHASSIS) TP21 AA4 AA7 RFDCI CN101 28P 7V MGND MGND STBY MDP SFDR SRDR TFDR TRDR FFDR FRDR SSTP VCC(4.5V) GND GND FE TP68 (FE) TP69 TP70 (TE) TP71 (RFDC) TP72 (RFAC) TP73 TP74 TP75 TP76 TP77 TP78 TP79 TP80 R234 0 AA6 AA7 (DVC) C213 0 AA1 TP57 TP58 TP59 TP60 TP61 TP62 TP63 TP64 TP65 TP66 TP67 TP55 TP56 R236 1k R229 2.2k R118 0 R117 47k DC_OFST SELECT SWITCH R113 2.7k R109 100k VFC RFC VC RFDCO
RFAC DVC DVCC R231 1k SW R126 33k F R125 33k E TP24 D TP23 C B A VCC GND TP51 AC_SUM EQ_IN PD TP52 LD C114 0.001 F+ C110 0.1 CC5 TP53 TP50 TFT+ R228 470k LD_GND AA8 LD CC4 CC5 PD CC3 TP54 SW CC2 CC4 PD1 CC1 GND AA6 CC3 PD2
AA2
IC103 CXA2581N-T
BB7 RF AMP, BB8 BB1 BB2 FOCUS/TRACKING ERROR AMP
Q101 2SB710A-RT AUTOMATIC POWER CONTROL TP22 R124 10
C118 1
BB3 BB4 BB5 BB6 R235 1k C108 0.1 C111 47 4V
R122 100k
C113 100 4V
C119 1 R123 10
BB3
TE RFDC RFAC DVC DVCC(2.5V) LD ON(D/A4) D/A3 D/A2 D/A1 CTRL LD GND
AA3 AA4 AA5
BB6
BB5
BB4
(Page 30)
SE
AA2
C166 0.1
C182 100 10V
IN2-
IN2+
IN1-
IN1+
VO1+
VO1-
VO2+ VO3-
NC (VPUMP1)
NC(BC1)
NC(BC2)
PVCC1
OPO2(NC)
OPO1(NC)
NC(VDD)
PVCC1
PVCC/ 2(NC)
SGND
OP.O
PGND1
AA9 AA10 C165 10 16V C153 0.1 FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE
OPO3(NC)
NC(SW)
ABS
NC(CT)
NC(FB)
(VPUMP2)
NC(BC3)
NC(BC4)
PGND2
SVCC
STBY
VO4+
IN4
NC
VO3+
NC
NC
VO4-
IN4R
IN3+
IN3-
NC
NC
NC
NC
IC102 AN41020A
PGND2
VREF
PVCC2
PVCC2
PGND1
VO2-
OP+
OP-
NC
NC
NC
NC
NC
AA8
R179 10k
M102 (SLED)
R176 0 R152 4.7k M101 (SPINDLE)
R151 100k
C151 0.022
BB1
BB8
BB7
BB2
C163 100 10V
C164 0.1
· Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
29
29
HCD-RV7/RV8
7-9.
SCHEMATIC DIAGRAM VIDEO Board (1/2)
· See page 35 for Waveforms.
· See page 54 for IC Block Diagrams.
(1/2)
N.C. D+5V(SW) D-0UT D-GND L-CH A-GND R-CH A+5V(SW) SYS RST SYS OUT SYS IN SYS CLK TP419 TP418 TP417 TP416 TP415 (L-OUT) TP414 TP413 (R-OUT) TP412 TP411 TP410 TP409 TP408 TP407 TP406 TP405 TP404 TP403 TP402 TP401 SCS 1887SI 1887SO SCK SRQ SOK C259 100 6.3V C258 0.1
R152 100
C155 0.0047
R158 1.5k
C154 22 6.3V
204 203 201
IC301 BA7046F-E2 TP311 GND TP312 R301 220k
C303 10 16V
VD OUT TP310
R306 1k
4 1 R102 100 IC102(1/2) NJM2100M(T E2) C116 100 6.3V LOW-PASS L102 2.2µH R114 2.2k FILTER C156 1200p DIGITAL FILTER, D/A CONVERTER 2 3 R159 1.5k R157 10k
VIDEO SYNC IN OUT VCC HD OUT
TP304 R307 10k
TP309 C307 150p
TP313 P.CP ROSC
R308 10k TP305
AGND ROUT VCOM LOUT DZFR VCC
DGND LRCK
C308 150p
MCLK BCK DATA
VDD
R309 10k
R310 1k
R302 470
DZFL
DATA
SYNC SEPARATOR C301 10 C302 C305 16V 0.1 0.1 R303 120k R305 10k
C309 220p IC302 TC74VHCU04 FT(EL)
CLK
(Page 38)
SYS RQ SYS OK N.C. VIDEO MUTE SYS CS M-GND M+7V(UNSW) CN201 19P
C114 22 6.3V C115 0.1 R115 2.2k 7
8
C106 1200p 5 6
R109 1.5k
R108 1.5k
R107 10k
IC504 PCM1748E/2K Q581 2SC4154TP -1EF R581 100 R582 470 +3.3V REGULATOR
29 26 30
LAT
C SYNC BUFFER
C596 10 16V
C581 0.1
IC102(2/2) NJM2100M(T E2)
C104 22 6.3V C105 0.0047
205
L301
C584 0.1
C583 0.1
C582 10 16V
C597 10 16V
A1
A2
CN101 28P LD GND CTRL D/A1 D/A2 D/A3 LD ON(D/A4) DVCC(2.5V) DVC RFAC RFDC TE SE FE GND GND TP434 TP433 TP432 TP431 TP430 TP429 TP428 TP427 TP426 TP425 TP424 135 143 142 141 TP448 TP447 TP446 TP445 TP444 TP443 TP442 TP441 TP440 TP439 TP438 TP437 TP436 165 173 160 162 163 164
JW203 0
IC201 µPC2925T-E1 I O G C201 22 6.3V C202 0.1
+2.5V REGULATOR FB201
A4 A5
3 5 6 9 FB251 C254 0.1
C213 22 6.3V
C203 100 6.3V
C204 0.1
C205 0.1
C206 0.1
C207 0.1
C208 0.1
A6 A7 A8 A9
R316 10k +3.3V REGULATOR IC202 I C209 22 6.3V BA033FP-E2 G O C214 22 6.3V FL201 I G O C211 100 6.3V L311 R312 0 C312 15p
R314 10k
C AMP IC303 NJM2255M (TE2)
C253 0
TP301
C314 0.1
R318 100 C315 47p
TP302
2
C210 0.1
C212 0.1 FL501 O G I R311 220 C313 10p
VIN COLOR OFFSET COLOR C311 22p R317 10k R315 10k C318 100 6.3V FL502 O C567 0.1 G I R323 470 TP303 L322 220µH R326 2.2k C317 0.1 V+
TINT GND
(Page 29)
VCC(4.5V) SSTP FRDR FFDR TRDR TFDR SRDR SFDR MDP STBY MGND MGND 7V
VOUT
C255 0.1
R561 1k
C574 0.1
BGP
C339 100 6.3V
C338 0.1
FB561
FB252
140 138 137 133
C257 68 10V
C566 100 6.3V C561 0.1
IC506 BU2507FV-E2
C328 0.0047 R325 2.7k
C327 22p C329 0.01
13
R327 100 TP306
VDD AO5
VCC AO6
6 R202 100 5
9 28 D-RAM IC507 VG3612816BT -7L VDD 49 DQ0 VDDQ 50 DQ1 DQ14 64 DQ2 C575 100 6.3V VSSQ 52 DQ3 53 DQ4 DQ11 VSSQ 61 DQ5 55 DQ6 45 VSSQ 66 63 C571 0.1 56 DQ7 VDD 62 77 LDQM 43 73 WE 44 68 CAS 60 72 RAS JW524 0 74 CS 59 76 BA0 JW523 0 BA1 56 45 A10/AP 55 34 A0 54 35 A1 53 36 A2 52 37 A3 VDD C576 100 6.3V A4 VSS C364 10 16V A5 39 BUF OUT STBY IN GND OUTSAG BUFIN VCC OUT A6 40 A7 41 IC307 BD7600FV-E2 A8 42 A11 44 A9 43 NC Q370 RT1N141M-TP-1 VIDEO MUTING CONTROL SWITCH VIDEO AMP CKE CLK UDQM 70 R376 10k NC/RFU 78 D8 VSS DQ9 VDDQ 59 C572 0.1 C361 0.1 DQ10 60 FB360 VDDQ C573 0.1 54 DQ12 62 R321 220 DQ13 VDDQ 63 VSS 66 DQ15 VSSQ 65 C321 22p C323 10p Q301 2SA1602TP1EF SYNC BUFFER C322 15p
AO4 RST 3 AO3
LD 29 CLK 30 DI 13 AO1 GND
V+
DIF
DIF
CUNT
TP422 TP421
2 AO2 VSS
L321 2.2µH
R322 0
Y AMP
COMPENSATION
PHASE
FREQ
VIN
GND
NC
NC
D/A CONVERTER
51
C324 22 6.3V C325 220p R324 150 C326 150p
IC508 MR27V401E066MAZ020 VPP 65 A16 64 A15 61 A12 42 A7 C221 R201 10 100 16V C222 10 16V C223 100 6.3V C224 0.1 41 A6 40 A5 39 A4 37 A3 36 A2 35 A1 34 A0 49 DQ0 50 DQ1 CN301 3P VMP GND VMP-VIDEO IN VMP GND
TP307
NC
IC304 NJM2209M (TE2)
DELAY
VOUT
IN
IN
OUT
NC
NC
(Page 31)
A10
Q201 2SD999-T1 -CLCK +4.5V REGULATOR
VCC A18 A17 A14 A13 A8 A9 A11 OE A10 CE DQ7 DQ6 DQ5 DQ4 DQ3
C360 100 6.3V
Q302 2SC4154TP1EF Y SYNC BUFFER JW301 0
C363 10 16V
51 DQ2 VSS
R374 4.3k
R372 2.2k
R373 2.2k
C365 100 6.3V
R375 75
PROGRAM ROM
(Page 38)
TP308 (V-OUT)
C366 100 6.3V
A11 A12 A13
A14
30
30
· Voltages are dc with respect to ground under no-signal conditions. no mark : VIDEO CD PLAY : Impossible to measure
HCD-RV7/RV8
7-10. SCHEMATIC DIAGRAM VIDEO Board (2/2) · See page 35 for Waveforms.
(2/2)
FL503 FB504 FB503 TP197 I TP216 C550 8p C549 8p A1
204 205 203 201
FL504 O G I FB502 TP191 C545 C543 1 50V 470p C544 0.47 R552 820
TP193
FB501 TP177 C542 0.1 C541 C539 0.01 0.47
R548 680k C537 100p
G
O
R557 10
R556 10
X502 27MHz
R558 1M
TP208
TP204
TP201
TP205
TP192
TP203
R551 1.6k
C540 0.47
TP183 (4.2336MHz) TP178 TP172 TP173
C535 0.068 R545 1k
R544 1M
TP182
TP198
TP209 TP202
R546 180k
TP215 R501 47k
RESERVE
V AVD1
A2
V AVS1
RV501 100k
RESERVE
R543 470k
C551 0.1
R559 470
R555 10
C548 0.1
C546 0.1
C536 150p
R542 0
R554 10
C538 100 6.3V
C534 470p
R550 10k
C570 0.0033 R547 10k
165
163
C552 1 50V
164
C547 1 50V
173
R549 100k
C533 0.1
R541 0
C502 0.1 R502 3.3k C501 10 16V A4 C503 0.1
TP1 TP2 TP3 TP4 TP5
R534 0 162
160 TP159 TP158 TP157 TP156 CSIG C524 20p C525 1 50V
A5 TP6 A6 TP7 A7 TP8 A8 TP9 V AVS2 TP10 A9 TP11 I2C CLK TP12 I2C DATA 1887SI 1887SO SCK SRQ R503 10 R504 10 R505 10 R506 10 TP13 TP14 TP15 TP16 TP17 SOK SCS R507 10 R508 10 TP18 TP19 TP20 R513 10k C504 0.1 TP21 TP22 TP23 TP24 R509 10 TP25 TP26 TP27 DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, MPEG VIDEO/AUDIO DECODER, VIDEO SIGNAL ENCODER 30 R512 10 TP30 TP31 IC505 CXD1887R 133 TP132 TP136 135 TP134 138 137 R531 100k C521 0.1 143 142 141 140 TP146 TP145 R532 4.7k X501 33.8688MHz C522 7p C523 7p RESERVE TP151 V AVD2 RESERVE R533 33k R538 10k
A10 26
(Page 30)
28 29
R510 10 R511 10
TP28 TP29
L FOK TP33 34 35 36 37 L SCOR 39 40 L CDC2PO 41 42 43 L GFS 44 45 TP119 TP118 TP117 C505 0.1 TP116 TP115 49 L SCLK 50 51 L SENS 52 53 L DCLK 54
L CDLRCK L CDDATA RESERVE RESERVE L CDBCK L CDXRST
TP130 TP129 TP128 TP127 TP126
TP124
TP122 TP121
TP113
TP111
TP109
SYSRST
L SQCK
DRWEL
L SQSO
DRRAS
DRCAS
L DDAT
TP70 (54MHz)
IVS5
TP94
TP88
TP93
TP89
TP102
TP100
TP74
TP72
TP73
TP84
TP82
TP81
TP83
TP79
TP80
TP67
TP85
TP68
TP86
TP97
TP96
62
55
64
63
56
59
60
65
68
66
61
73
70
76
72
74
77
78
A11 A12
C513 0.001
C511 0.1
C510 0.1
R522 10k
A13 A14
TP99
TP91
31
31
· Voltages are dc with respect to ground under no-signal conditions. no mark : VIDEO CD PLAY : Impossible to measure
TP106
L XLAT
NVOEL
DRCK
HCD-RV7/RV8
7-11. PRINTED WIRING BOARD VIDEO Board
· Semiconductor Location
Ref. No. IC102 IC201 IC202 IC301 IC302 IC303 IC304 IC307 IC504 IC505 IC506 IC507 IC508 Q201 Q301 Q302 Q370 Q581 Location D-6 I-12 I-2 D-6 C-6 E-6 F-6 B-9 G-9 F-4 C-12 C-11 C-4 H-12 F-9 C-8 A-9 G-8
· See page 27 for Circuit Boards Location.
1
2
3
4
5
6
(Page 37)
7
8
9
10
11
12
13
A
VIDEO BOARD (COMPONENT SIDE)
Q
MAIN BOARD CN784
VIDEO BOARD (CONDUCTOR SIDE)
E
B
TP308 (V-OUT) 17 16
IC307
IC506
27 1 8 7
C
TP70 (54MHz)
IC508
IC302
7 1 E
14
1
IC507
8 14 E 28 54
D
108 109
32
1
55 54
IC301
E
28 27
IC303 IC505
E
F
8 7
A
BD BOARD CN101
162 163 TP182 (4.2336MHz) 216
1
(Page 28)
14
1
G
2 1
IC304
E 1 16
IC504
8 9 E
H
TP415 (L-OUT) TP413 (R-OUT)
I
IC202
3
1
IC102
12 1-684-173(12)
3
1
IC201
1-684-173-
12 (12)
J
T
MAIN BOARD CN201
(Page 37)
32
32
HCD-RV7/RV8
7-12. PRINTED WIRING BOARDS DRIVER/MOTOR/SENSOR (CD) Boards
· See page 27 for Circuit Boards Location.
M721 (TURN)
C712
IC711
IC701
S701 DISC TRAY OPEN/CLOSE DETECT
OPTICAL PICK-UP UP/DOWN DETECT
4
14 14 (14)
1
(14)
14 (14)
B
CN202 (Page 37)
7-13. SCHEMATIC DIAGRAM DRIVER/MOTOR/SENSOR (CD) Boards · See page 54 for IC Block Diagram.
TURN MOTOR DRIVER
S701 DISC TRAY OPEN/CLOSE DETECT OPEN CLOSE (LOAD IN) (LOAD OUT) D+3.3V D+3.3V 3.3 0.2 C712 0.1 D. GND S711 OPTICAL PICK-UP UP/DOWN DETECT D+3.3V
IC711 SG-264 DISC TRAY STATUS SENSOR
B
MAIN BOARD (1/4) CN202
(Page 38)
D. GND D. GND
· Voltages are dc with respect to ground under no-signal conditions. no mark : CD PLAY
33
33
HCD-RV7/RV8
7-14. PRINTED WIRING BOARDS SW/HEAD (A)/HEAD (B) Boards
1 2 3 4 5
· See page 27 for Circuit Boards Location.
6
M901 (CAPSTAN)
7
8
9
10
PM902 (DECK B)
11
12
M
A
PM901 (DECK A)
IC1002 IC1001
B
1 (DECK A PLAY) (DECK B HALF) (DECK B REC) 4
(DECK B PLAY)
C
DECK A HALF
(DECK A REC)
D
C
CN304 (Page 37)
E
HP901 (PB HEAD) (DECK A)
HPRE901 (REC/PB/ERASE HEAD) (DECK B)
· Semiconductor Location
Ref. No. D1001 D1002 Location B-4 B-10 B-2 B-10 B-3
(12)
F
(12)
IC1001 IC1002 Q1001
R
NO302 (Page 37)
S
NO303 (Page 37)
34
34
HCD-RV7/RV8
7-15. SCHEMATIC DIAGRAM SW Board
· Waveforms BD Board
1 IC103 qg (RFAC) (CD Play Mode)
VIDEO Board
ea IC504 1 (BCK)
1.05 ± 0.3 Vp-p
(CAPSTAN)
3.3 Vp-p
[8.2] [0] C1001 33 10V CAPSTAN MOTOR CONTROL SWITCH [8.2]
474 ns
2 IC103 qh (FE) (CD Play Mode)
TAPE SPEED (NORMAL) TAPE SPEED (HIGH)
es IC504 3 (LRCK)
Approx. 250 mVp-p
2.7 Vp-p
[] {2.9} <<2.9>> [3.3] [3.3]
[1.5] {} <<>>
22.7 µs
3 IC103 qk (TE) (CD Play Mode) ed IC504 qh (MCLK)
PM902 (DECK B)
PM901 (DECK A)
ROTATION DETECT SENSOR (DECK A)
ROTATION DETECT SENSOR (DECK B)
CAPM- CAPM+ CAPMH/L ATRGM+
S1003 (DECK A HALF)
+3.3V
TRGMGND BTRGM+
Approx. 350 mVp-p
3.4 Vp-p
S1005 (DECK A REC) +3.3V +3.3V
C
MAIN BOARD (3/4) CN304
S1006 (DECK B HALF)
(Page 40)
S1009 (DECK B REC)
59.5 ns
4 IC103 wk (RFDC) (CD Play Mode) ef IC303 1 (VIN), IC505 7 (CSIG) (Video CD Play Mode)
S1001 (DECK A PLAY)
S1002 (DECK B PLAY)
0.75 ± 0.1 Vp-p
480 mVp-p
+3.3V
H
eg IC303 6 (VOUT) (Video CD Play Mode) · Voltages are dc with respect to ground under no-signal conditions. [ ] : TAPE PLAY (DECK A) { } : TAPE PLAY (DECK B) : REC : Impossible to measure
600 mVp-p
H
35
35
HCD-RV7/RV8
MAIN Board
eh IC304 1 (VOUT), IC505 6 (CPSIG) (Video CD Play Mode) ra IC505
PANEL Board
wa IC601 is (X0)
1.5 Vp-p
1.05 ± 0.3 Vp-p
580 mVp-p
2.1 Vp-p
2.1 Vp-p
2.8 Vp-p
H
7.6 µs
rs IC505
12.1 µs
qs Q302, Q303 (Collector) (Rec Mode)
H
250 ns
ej IC307 8 (BUF IN) (Video CD Play Mode)
3.3 Vp-p
300 mVp-p
2.9 Vp-p
10.8Vp-p
H
29.5 ns
rd IC505
37 ns
12.1 µs
qd Q302, Q303 (Emitter) (Rec Mode)
ek IC307 6 (BUF OUT) (Video CD Play Mode)
0.75 ± 0.1 Vp-p
2.1 Vp-p
0.4 Vp-p
H
el IC505 ij (L CDLRCK), ik (LRCK) rf IC505
12.1 µs
qf IC501 qa (XC-OUT)
2.7 Vp-p
Approx. 350 mVp-p
2.4 Vp-p
22.7 µs
r; IC505 os (L CDBCK), od (BCK) rg IC505
30.5 µs
qg IC501 qd (X-OUT)
3.3 Vp-p
Approx. 250 mVp-p
1.9 Vp-p
474 ns
62.