Text preview for : SONY DSC-W100 SERVICE MANUAL LEVEL 2 VER 1.3 2007.04 (9-876-941-34).pdf part of SONY DSC-W100 SONY DSC-W100
DIGITAL STILL CAMERA.
SERVICE MANUAL VERSION 1.3 2007.04
PART# (9-876-941-34)
Back to : SONY DSC-W100 SERVICE MAN | Home
DSC-W100
SERVICE MANUAL
Ver. 1.3 2007.04
Revision History How to use Acrobat Reader LEVEL
2
Internal memory ON BOARD
Photo: Silver
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Brazilian Model Tourist Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAM SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· Precaution on Replacing the SY-154 Board
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DIGITAL STILL CAMERA
DSC-W100_L2
9-876-941-31
Sony EMCS Co.
2007D0500-1 © 2007.4 Published by Kohda TEC
SPECIFICATIONS
Camera
[System]
Image device 9.10 mm (1/1.8 type) color CCD, Primary color filter Power consumption (during shooting with the LCD screen on) 0.95 W Operating temperature 0 to 40°C (32 to 104°F) Storage temperature -20 to +60°C (-4 to +140°F) Dimensions 94.2 × 60.6 × 24.8 mm (3 3/4 inches × 2 1/2 inches × 1 inches) (W/H/D, excluding protrusions) Approx. 192 g (6.8 oz) (including NP-BG1 battery pack and wrist strap, etc.) Electret condenser microphone Dynamic speaker Compatible
Total pixel number of camera Approx. 8 303 000 pixels Effective pixel number of camera Approx. 8 068 000 pixels Lens Carl Zeiss Vario-Tessar 3 × zoom lens f = 7.9 - 23.7 mm (38 - 114 mm when converted to a 35 mm still camera) F2.8 - 5.2
Mass
Exposure control Automatic exposure, Manual exposure, Scene Selection (6 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash
Microphone Speaker Exif Print
PRINT Image Matching III Compatible PictBridge Compatible
File format (DCF compliant) Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media Internal Memory (64 MB) "Memory Stick Duo" Flash Recommended distance (ISO set to Auto): approx. 0.2 m to 6 m (7 7/8 inches to 19 feet 8 7/8 inches) (W)/approx. 0.3 m to 3.2 m (11 7/8 inches to 10 feet 6 3/8 inches) (T)
BC-CSG battery charger
Power requirements AC 100 to 240 V, 50/60 Hz, 2W Output voltage DC 4.2 V, 0.25 A Operating temperature 0 to 40°C (32 to 104°F) Storage temperature -20 to +60°C (-4 to +140°F) Dimensions Approx. 62 × 24 × 91 mm (2 1/2 × 31/32 × 3 5/8 inches) (W/H/D) Approx. 75 g (2.7 oz)
[Input and Output connectors]
Multi connector USB communication Hi-Speed USB (USB 2.0 compliant) Mass
Rechargeable battery pack NP-BG1
Used battery Lithium-ion battery Maximum voltage DC 4.2 V Nominal voltage DC 3.6 V Capacity 3.6 Wh (960 mAh)
[LCD screen]
LCD panel 6.2 cm (2.5 type) TFT drive Total number of dots 115 200 (480 × 240) dots
[Power, general]
Power Rechargeable battery pack NPBG1, 3.6 V AC-LS5K AC Adaptor (not supplied), 4.2 V
Design and specifications are subject to change without notice.
DSC-W100_L2 --2--
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. FLEXIBLE Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
DSC-W100_L2
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
TABLE OF CONTENTS
Section Title Page
1.
SERVICE NOTE
1-1. Description on Self-diagnosis Display ···························· 1-1 1-2. Process After Fixing Flash Error ····································· 1-1 1-3. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-2 1-4. Precaution on Replacing the SY-154 Board ···················· 1-3
2.
DISASSEMBLY
2-1. Disassembly ····································································· 2-2 2-2. Exchange Method of Barrier Assy ·································· 2-6
3.
BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-2 3-3. Power Block Diagram ····················································· 3-3
4.
4-1. 4-2. 4-3. 4-4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Frame Schematic Diagram ·············································· 4-1 Schematic Diagrams ························································ 4-3 Printed Wiring Boards ··················································· 4-17 Mounted Parts Location ················································ 4-26
5.
REPAIR PARTS LIST
5-1. Exploded Views ······························································· 5-2 5-2. Electrical Parts List ························································· 5-7
DSC-W100_L2 --4--
1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display · C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) · E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code C:32:ss Countermeasure Turn the power off and on again. Format the "Memory Stick" or internal memory. Insert a new "Memory Stick". Turn the power off and on again. E:61:ss E:91:ss Checking of lens drive circuit. Checking of flash unit or replacement of flash unit. (Note) Cause Trouble with hardware. "Memory Stick" or internal memory is unformatted. "Memory Stick" is broken. Trouble with internal memory. When failed in the focus and zoom initialization. Abnormality when flash is being charged. Caution Display During Error SYSTEM ERROR FORMAT ERROR MEMORY STICK ERROR INTERNAL MEMORY ERROR --
C:13:ss
Note: After repair, be sure to perform "1-2. PROCESS AFTER FIXING FLASH ERROR".
1-2. PROCESS AFTER FIXING FLASH ERROR
When "FLASH error" (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK Cancel
See the following procedure. Cancels the resetting.
1 Select [OK] with v on the control button, then press z. The message "Initialize all settings Ready?" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting.
· Make sure that the power is not disconnected during resetting.
DSC-W100_L2 1-1
1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-154 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-154 board or the IC202 on the SY-154 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a "Memory Stick Duo".
OK Cancel
See the following procedure. Cancels the copying.
1 Insert a "Memory Stick Duo" having 64 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be copied Ready?" appears. 3 Select [OK] with v, then press z. Copying starts.
Copying 102_COPY
· Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files using a battery pack with little remaining charge, thebattery pack may run out, causing copying to fail or possibly corrupting the data. · You cannot copy individual images. · The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick Duo" after copying , then execute the [Format] comm and in (Internal Memory Tool) (page 52). · You cannot select a folder copied on a "Memory Stick Duo". · Even if you copy data, a (Print order) mark is not copied.
Method for Formatting the Internal Memory
This item does not appear when a "Memory Stick Duo" is inserted in the camera. The default settings are marked with .
Format
Formats the internal memory.
· Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK Cancel
See the following procedure. Cancels the formatting.
1 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be erased Ready?" appears. 2 Select [OK] with v, then press z. The format is complete.
DSC-W100_L2 1-2
1-4. PRECAUTION ON REPLACING THE SY-154 BOARD
VIDEO OUT Default Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting because of broadcast system (NTSC/PAL). When the data has changed because of board replacing etc., check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value. VIDEO OUT Default Data Page 4F Address 8D, A2 Data NTSC 00 PAL 01
Writing Method: 1) Select page: 00, address: 01, and set data: 01. 2) Select page: 40, address: 70, and set data: 01. 3) Select page: 40, address: 98, and check that the data is "00". 4) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL). 5) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL). 6) Click [Save] on the SEUS screen. 7) Select page: 80, address: 34, and check that the data is "00". 8) Select page: 80, address: 30, and check that the data is "00". 9) Select page: 00, address: 01, and set data: 00.
Initial Language Data Check
If the SY-154 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial language as that of the set distributing in each region. Initial language: Language displayed at the next starting if the setting of Setup menu was reset. It is different from the language setting selectable with the menu. Initial Language Data Page Address Data 00 04 06 08 0B 0D Language English Spanish Portugal Simplified Chinese Russian Korean GP2 z GP3 z z GP4 z z z z z z
4F
88, 8C
Note: GP2 is fixed to English. GP3 is either English, Spanish, or Russian. GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean. Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 40, address: 70, and set data: 01. 3) Select page: 40, address: 98, and check that the data is "00". 4) Select page: 4F, address: 88, and set the Initial Language Data. 5) Select page: 4F, address: 8C, and set the Initial Language Data. 6) Click [Save] on the SEUS screen. 7) Select page: 80, address: 34, and check that the data is "00". 8) Select page: 80, address: 30, and check that the data is "00". 9) Select page: 00, address: 01, and set data: 00. 10) Turn off the camera. 11) Turn on the camera. Execute "Initialize" of Setup screen. 12) Check the language displayed when the camera starts.
DSC-W100_L2 1-3E
2. DISASSEMBLY
NOTE FOR REPAIR
· Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. · When remove a connector, dont' pull at wire of connector. It is possible that a wire is snapped. · When installing a connector, dont' press down at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)
DISCHARGING OF THE ST-146 FLEXIBLE BOARD'S CHARGING CAPACITOR (C007)
The charging capacitor (C007) of the ST-146 flexible board is charged up to the maximum 330 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a resistor of 1 k /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
1 k/1 W
Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds.
Wrap insulating tape.
R:1 k/1 W (Part code: 1-215-869-11)
DSC-W100_L2 2-1
HELP
2-1. DISASSEMBLY
2-1-1. CABINET SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
HARDWARE LIST
1 Cabinet (Rear) Block (1-1 to 1-6) 2 Cabinet (Front) Block (2-1 to 2-3)
1 Cabinet (Rear) Block
1-6 (Claw) 2-1 1-1 (#26/#27)
1-5 (#20/#21) 2-3 (Claw)
1-3 (#20/#21) 1-2 (Open) 1-4 (#20/#21)
Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds.
2-2 (#20/#21)
2 Cabinet (Front) Block
R:1 k/1 W (Part code: 1-215-869-11)
DSC-W100_L2 2-2
2-1-2. LCD PANEL SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
HARDWARE LIST
1 Control Switch Block (1-1 to 1-2) 2 LCD Block (2-1 to 2-8)
2-1 2-8
1 Control Switch Block
1-1 (#3)
SW-479
2-2 (#3)
2-5
2-7 2-6
1-2
2-4 (Claw)
2-3 (Claw)
2 LCD Block
DSC-W100_L2 2-3
2-1-3. CABINET (TOP) SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
1 Cabinet (Top) Block (1-1 to 1-8) 2 Capacitor Holder Block (2-1 to 2-4) 3 Lens Block (3-1 to 3-4)
1 Cabinet (Top) Block
1-7 (Open) 1-4 (Claw) 1-1 (Boss) 1-2
1-8 1-3 (Adhesive sheet) 1-5 1-6
2-3
3-3 (Claw) 3-2 (Claw) 3-1
2-4 (Claw)
3-4 2-2 2-1
2 Capacitor Holder Block
3 Lens Block
DSC-W100_L2 2-4
MC-162
2-1-4. BT HOLDER SECTION
Follow the disassembly in the numerical order given.
EXPLODED VIEW
HARDWARE LIST
1 SY-154 Board (1-1 to 1-4) 2 DC-105 Flexible Board (2-1 to 2-13)
2-6
2-2 (Slide in the direction of arrow) 2-5 (Boss) 2-4 2-1 (Boss)
05 -1 C D
2 DC-105 Flexible Board
2-7 (Claw)
2-3 (Claw)
1-3 2-10 (Claw)
1-1 (#3)
1-4
2-12 (Claw) 2-11
2-8 2-9 (#5)
SY -15
4
2-13 1-2 (Claw)
1 SY-154 Board
DSC-W100_L2 2-5
2-2. EXCHANGE METHOD OF BARRIER ASSY
Service parts Part Number 1 2 3 3-091-427-01 X-3954-476-1 3-086-156-31 Part Name Ring (A), Ornamental Barrier Assy Tapping screw (P2) Quantity 1 1 2
1
Tools used Torque driver Soldering iron Weight about 60g Adhesive (Super X) (Note) Note: Use adhesive (Super X) or an equivalent article. Don't use what becomes white after drying like a quick-drying glue.
2
3
2-2-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force. Heat four circled portions with the soldering iron. Heating temperature is about 300ºC. Beware of a burn since the entire Ornamental Ring becomes hot. * As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame. Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring. * Take extreme care so as not to damage the coated surface of the group-1 frame. In case of difficult peeling, heat the ring again with the soldering iron. If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 2 3 4 in the under figure one by one sequentially. * Discard the removed Ornamental Ring A.
4 2 3
Tip
1
DSC-W100_L2 2-6
2-2-2. REMOVE OLD BARRIER ASSY
1 Remove two screws. * Discard the removed screws. 2 Remove the Barrier Assy. * Discard the removed Barrier Assy.
1 1
2
* After removing the Barrier Assy, if the "G1 Dust-Proof Ring" was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction. This is an important part to prevent the dust and light from coming in. * After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-2-3. INSTALL NEW BARRIER ASSY
1 Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure. 2 Tighten two screws. * Tightening torque = 0.5 kgf
Projection 1
2 2
DSC-W100_L2 2-7
2-2-4. ADHERE THE ORNAMENTAL RING A
Apply an adhesive to four recesses on the top surface of the Barrier Assy. * Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.) Meeting a "notch" of the Ornamental Ring A with a "projection" of the group-1 frame, push the Ornamental Ring A into the group-1 frame. * The projection of the spring for preventing static electricity must be tilted. Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens. Note: Be careful not to give a shock. * After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame. A gap, if present, causes the crackle sound NG. * The weight must push in the Ornamental Ring A only. If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Do not put the weight on a black mold part. Notch Adhesive Adhesive Adhesive Projection
Adhesive Not gap in full circumference.
Completion after 30 minutes.
DSC-W100_L2 2-8E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Boss of DC flexible support Claw of main frame DC-105 flexible board
DSC-W100_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM
DSC-W100_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS BLOCK LENS IRIS (METER)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-154 BOARD (1/2) SW-479 BOARD (1/2)
K5, G4, H4, L5, H2, H1, J1, J2, M5, J4, K4, M6, K2, K1
CD-628 FLEXIBLE BOARD
D1, E3 - E1, F3 - F1, G3 - G1, H3 - H1, J1
CN708 (1/2)
11, 10, 14 24 - 17 D8, D7, E8, E7, D6, D5, E9, B8, D9 E6, B4
FP-427 FLEXIBLE BOARD (1/2)
23, 24, 20 10 - 17
CN001 (1/2) D0 - D7
CN002
30, 31, 29 21 - 28
17
1
IC002 BUFFER
3
29
CN301 CCD_OUT
H10
CA_AD00 - CA_AD13
LCD_D0 LCD_D7 LCD D0 - LCD D7 LCD_HD, LCD_VD, LCD_CK
D0 - D7 HSYNC, VSYNC, DCLK
IC001 CCD IMAGER
28, 29, 25, 24 40, 42, 38, 36 K6, K5, J6, J5
HSYNC, VSYNC, DCLK
LCD901 2.5 INCH COLOR LCD MONITOR
IC301 H1A, H2A, H1B, H2B CCD SIGNAL PROCESS, TIMING GENERATOR (1/7)
A2 A3 B1
CA_HD CA_FD
H5 J5
SHUTTER MOTOR
ZOOM MOTOR
FOCUS MOTOR
IRIS MOTOR
W25 F25 IC101 (1/2)
XCS_ PANEL P_ADJ XIC_101_RST_OUT
4 28 3
7, 8
XCS P_ADJ XRESET SO, SI, SCLK
30 6 31
27, 26
XCS VCOMH XRESET SO, SI, SCLK
34 15 35
33, 32
M
M
M
M
23
1, 4, 6 - 15
34
3, 5, 7 - 16
RG V1, V2, V3A, V3B, V4, V5A, V5B, V6, V7, V8, V9, V10
K4
G7, H6, G6, G5, H5, H4, G4, F4, E4, D7, H7, D4
A4
CLKTGO
FOCUS RESET SENSOR
5 3 26 27
6 4 22 21
VHLD VST VSUB VSUB_CONT Q302
E1 F2 U22
IC_101_1_SO, XIC_101_1_SCK
D5 D6 C4
CAMERA DSP, LENS CONTROL, MODE CONTROL (2/7)
C2 C1
B3, C3
XCS_FE XIC_101_RST_OUT
2 1
BL_H BL_L
32 33
BL_H BL_L
CN003 6 1
D901 BACKLIGHT
E7
IC_101_1_SO, XIC_101_1_SCK VSUB_CONT_PRE, VSUB_CONT_POST
Q301
T4, R23
AF4
XIC_101_RST_OUT
IC401 LENS DRIVE (3/7) IRIS_ S_±, IRIS_ M_± FOCUS_A, FOCUS_A, FOCUS_B, FOCUS_B IRIS MOTOR DRIVER FOCUS MOTOR DRIVER ZOOM MOTOR DRIVER SHUTTER MOTOR DRIVER
F2, E2, D2, B1
D4
XCAM_DR_PS
P21
BL_L BL_H
1
OVERALL (2/2) (PAGE 3-2)
CN401
5-8
IRIS_ S_±, IRIS_ M_± F_MOTOR_A, F_MOTOR_A, F_MOTOR_B, F_MOTOR_B
P6, R2, P4, N4
F5, G6, D3, E3
IRIS_S_IN, IRIS_S_EN, IRIS_M_IN, IRIS_M_EN FC_DIR_A, FC_DIR_B, FC_BRK_A ZM_DIR_A, ZM_BRK_A, ZM_BRK_B
AB6, AC4, AE4, AE5, U2, R6 AC5, AF6
MS_BS, MS_D0 - MS_D3, MS_CLK IC_101_1_SO, XIC_101_1_SCK IC_101_1_SO, XIC_101_1_SCK IC_101_VOUT IC_101_AUOUT IC_101_AUIN XCS_AUDIO
Z_DC_MOTOR_±
ZOOM_DC_±
P5, N2, N6 L4, N5, L2
A2, C4, B2
B4, B5
17 - 20
D5, A6, B6, C5
D6, E6, B7, C6
24 - 27
H26 K26 L26 Y26
AC1, AD1
2
1-4
SHUTTER_±
SHUTTER_±
MSHUT_DIR, MSHUT_EN
R5, R25
OVERALL (2/2) (PAGE 3-2)
G1, E4
F4, F3
USB_DP, USB_DM XIC_101_RST_OUT XIC_101_RST_OUT CPU_D00 - CPU_D15
ZOOM FG
ZOOM RESET SENSOR
F_PI_SENS_OUT Z_PI_SENS_OUT Z_BOX2_PI_SENS_Col, Z_BOX1_PI_SENS_Col
29 21
13, 10
FC_SENS ZM_SENS_1ST ZM_DC_FG_1A, ZM_DC_FG_1B
U4 V4
AB13, AA13, AE13, AF13, AF12, AE12, AA12, AC12, AC11, AB12, AE11, AF11, AE10, AB11, AC10, AB10 AF21, AF20, AE20, AB18, AB19, AC19, AB16, AE19, AF19, AF18, AE18, AA15, AC18, AC17, AB15, AE17, AF17, AE16, AB14, AC16, AC15 V5, W4
CPU_D00 - CPU_ D15
CPU_A01 - CPU_A21
CPU_A20, CPU_ A21
ST-146 FLEXIBLE BOARD
XE_H + TRIGGER FLASH UNIT TRIGGER_GND C007 CHARGING CAPACITOR 5 D002 6
T002
2, 4
ST_UNREG
B5 E8, D8, C8, B8, A8, B7, A7, C7, A2, B2, C2, A1, B1, C1, D2, D1, D4, B6, A6, C6, B3 F7, E6, E5, G5, E4, G3, E3, G1, G7, F6, F5, F4, D5, F3, F2, E2 L11, K10, K12, J11, E11, D12, D10, C10, L12, K11, J10, J12, E10, D11, D9, C9
CPU_A01 - CPU_ A21
CPU_D00 - CPU_ D15
LENS TEMP SENSOR
31
LENS_TEMP
J25
1, 3
M3, E3 IC201
B4
15
1, 2
IC001 FLASH CONTROL, CHARGE CONTROL
10 9 6 4
6 5 8 7
CN704 STRB_CHG XSTRB_FULL STRB_CHG_CONT STRB_ON Q701 MIS-FLASHING PREVENTION D_1.2V
AE6 R22 V23 AB22 R4 AF9
XCPU_CS0 E7 IC_101_27M_CLKO B4
BURST FLASH (4/7)
XE_L
D003
Q001 FLASH DRIVE
7
D15 AC6 A17 A18
D21, D22, D20, B22, A22, A23, B23, E20, E21, B24, A24, A25, B25, C25, C26, B26, E10, A10, D10, E11, B10, A11, B11, E12, D11, D12, F12, B12, A12, E13, D13, D14, F13, B15, F14, E14
XDSP_QCS0 XCPU_CS4 DSP_QCLKE DSP_QCLK
IC202 M8 L3 M7 N7 256M SDRAM, 64M SUPER AND (4/7)
D004 SELF-TIMER/ AF ILLUMINATOR 05
DSP_DQ0 - DSP_DQ31, DSP_DQM0 - DSP_DQM3
14
XAF_LED
DSP_AQ0 - DSP_AQ11, DSP_QBA0, DSP_QBA1
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
H9, G10, H10, F9, E9, D8, C8, F8, E8, G9, G2, G3, G4, D7, C7, F4, E5, D6, C6, G5, H2, H3, H8, F3, E4, D5, C5, M10. L10, H4, J6, F6 K9, J9, M9, L9, K8, J8, M5, L5, K4, J4, M4, L4, K3, J3, F7, F5, J7, J5
D17, D18, D16, B18, A19, B19, E16, D19, E19, E17, B20, A20, B21, A21
XAF_LED
3
OVERALL (2/2) (PAGE 3-2)
DSC-W100_L2 3-1
3-2. OVERALL BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-154 BOARD (2/2)
MS_BS, MS_D0 - MS_D3, MS_CLK
CN703 MS_BS, MS_D0 - MS_D3, MS_CLK
2 - 5, 7, 8
MEMORY STICK DUO
XMS_IN D702 (MS ACCESS) CN706 USB_DP, USB_DM USB_DP, USB_DM USB_VBUS
6
MC-162 FLEXIBLE BOARD
USB_DP, USB_DM USB_VBUS V_OUT 8 20 A_OUT_L XAV_JACK_IN 16 26
10, 12 3, 4
OVERALL (1/2) (PAGE 3-1)
2
1
6 CN001 MULTI CONNECTOR
IC_101_VOUT IC_101_AUOUT IC_101_AUIN XCS_AUDIO IC_101_1_SO, XIC_101_1_SCK
V_LINE_OUT F3 IC603 B6 A6 D6
A1, C1 E6, D5
F1 E2 A3 MIC_SIG AU_LINE_OUT XAV_JACK_IN
AUDIO/VIDEO AMP (5/7)
6 10
SP±
CN601 MIC_SIG
1
MIC901 MICROPHONE UNIT
XIC_101_RST_OUT CN707 (2/2)
7, 9
SP±
RL-064 FLEXIBLE BOARD (2/2)
SP±
SP901 SPEAKER
SW-479 BOARD (2/2) CONTOROL SWITCH BLOCK (SW60610)
MODE DIAL
6, 2
S050 - S057 FUNCTION KEY CN004
CN001 (2/2)
2, 1
FP-427 FLEXIBLE BOARD (2/2)
KEY_AD0, KEY_AD1
32, 33
E4 CN708 (2/2)
K23, L23
XACCESS_LED XAV_JACK_IN
VL_3V
1
U25 IC101 (2/2) FRONT CONTROL (2/7)
BT001 LITHIUM BATTERY
L22, L25
30, 31
4, 3
MODE_DIAL0, MODE_DIAL1
V25
XACV_IN
D001
11 - 14
IC102 (2/2) (2/7)
D003 Q102 BATTERY CHARGE DETECT
CN701
DC-105 FLEXIBLE BOARD
BATT_UNREG BATT_SIG
RL-064 FLEXIBLE BOARD (1/2)
D003 AE/AF LOCK /SELF-TIMER D001 FLASH CHARGING /RECORD D002 (POWER) S001 POWER CN707 (1/2) 3 XAE_LOCK_LED F22
AA26 AB25
IC_101_TXD4 IC_101_RXD4
3
4
+
S
BATT_SIG
10
BT901 BATTERY TERMINAL
IC102 (1/2) (2/7) A6 EXTAL 6 1
4
E22
1-4
XSTRB_LED
X101 12MHz
USB_VBUS XMS_IN
C9 B10
ACV_UNREG BATT/XEXT J001 DC IN
Q001, Q002 5 IC001 DC/DC CONVERTER, RESET (6/7) B8 H1 D004 ST_UNREG EVER_SRAM MS_VCC D_3.2V A_3.2V D_1.8V CAM_2.9V CAM_-7.5V CAM_15V M_5V D_1.2V
6
XPWR_LED
D23 X001 32.768kHz A9 A8
8
XPOWER_ON
2 1 XAE_LOCK_SW XSHUTTER_SW N21 P23
6-8
IC103 BATTERY AUTHENTICATE (2/7)
3
S002 (SHUTTER)
10 11
AA5, AB5, Y5
S003 (ZOOM) T S004 N (PLAYBACK)
S005 W (INDEX) XPLAY_SW
IC_101_0_SI, IC_101_0_SO, XIC_101_0_SCK XDD_RST_OUT XPWR_OFF BATT_SENS MS_PWR_ON
15
R26 Y4 AA23 K25 T25
A7 B7 D4 D3 E9 F9
C6, C5, B6
13
KEY_AD2
W23 H25
XCS_DD
A6
BL_H BL_L
1 3
OVERALL (1/2) (PAGE 3-1) OVERALL (1/2) (PAGE 3-1)
XPOWER_ON XPLAY_SW
C7 D7
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
A4
XAF_LED
05
DSC-W100_L2 3-2
3-3. POWER BLOCK DIAGRAM
J001 DC IN
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
DC-105 FLEXIBLE BOARD
1-4
FB003
SY-154 BOARD
CN701 ACV_UNREG F001 F002 ST_UNREG UNREG CN704 ST_UNREG
ST-146 FLEXIBLE BOARD
T002
9 - 11
L001 D004 SELF-TIMER/ AF ILLUMINATOR IC001 ST_5V
D002 + C007 CHARGING CAPACITOR
FLASH UNIT
BATT/XEXT BT901 BATTERY TERMINAL FB002
D003 5 D001
D_3.2V M_5V
13 12
Q001, Q002
FLASH CONTROL, CHARGE CONTROL
11 - 14
+
S BATT_SIG ACV_GND
BATT_UNREG IC001 DC/DC CONVERTER, RESET (6/7) J1 K1 J6 K6 A1 B1 C2 D10 UNREG1-1 UNREG1-2 UNREG2-1 UNREG2-2 PWR1-1 PWR1-2 PWR1-3 PWR2
10
6-9
FP-427 FLEXIBLE BOARD
CN708 D_3.2V L004 LX3 E10 D005 VO3 E9 VL3 F9 BL_H BL_L 2 1 BL_H BL_L 32 33 29 VDD 5
SW-479 BOARD
LCD901 CN001 L001 CN002 17 VDD 2.5 INCH COLOR LCD MONITOR D901 BACKLIGHT 6 1 BL_H BL_L
RL-064 FLEXIBLE BOARD
D003 AE/AF LOCK /SELF-TIMER D001 FLASH CHARGING /RECORD D002 (POWER) S001 POWER 5 CN707 D_3.2V
F003
CN003
8
XPOWER_ON
VO1-1 F1 VO1-2 F2 VFB1 H2 C7 XPWRON1 L003
D_3.2V IC601 2.9V REG (5/7) 4 Vin Vout 3 AU_2.9V D_3.2V M_5V IC603 AUDIO/VIDEO AMP (5/7) XZM_FG_LED LENS BLOCK CN401 Z_BOX1_PI_SENS_VCC 9 Z_BOX1_PI_SENS_OUT 12 GND (Z_BOX1) 11 Z_BOX2_PI_SENS_VCC 14 Z_BOX2_PI_SENS_OUT 15 GND (Z_BOX2) 16 23 22 Q401 28 XFC_RST_LED F_PI_SENS_VCC Z_PI_SENS_VCC GND (Z_PI_SENS)
BT001 LITHIUM BATTERY
1
VL_3V D004
B8 RTCBAT H1 LDO1
LDO2IN B3 LDO2 A3 LDO3IN B2 LDO3 A2
D_1.8V
ZOOM FG
CAM_2.9V D_3.2V L002 D_1.2V D_3.2V L001 L006 Q004, Q005 SWITCHING Q003 M_5V IC401 LENS DRIVE (3/7) XZM_RST_LED ZOOM RESET SENSOR FOCUS RESET SENSOR
D702 (MS ACCESS)
D_3.2V
LX2 C10 VFB2 D8 G2 MS_PWR MS_PWR_IN G1 D3 MS_PWR_ON
MEMORY STICK DUO
9
CN703 MS_VCC
EVER_SRAM
BATT_SIG XACV_IN
BG4 G9 TG4 F10 PSG4 G8 VFB4 F7
DC CONTROL
CAM_2.9V Q006 SWITCHING CAM_-7.5V D_3.2V
L302 FB302 L303 L304 FB304 IC301 CCD SIGNAL PROCESS, TIMING GENERATOR (1/7)
Q102 BATTERY CHARGE DETECT
AN[4] K25
BATT_SENS IC_101_0_SI, IC_101_0_SO, XIC_101_0_SCK
D4 DTG1 SCLK SI SO A6 CE A7 XRESET B7 XPWROFF
L007 PWR56OUT1 PWR56OUT2 LX5-1 LX5-2 LX5-3 LX5-4 VFB5 J7 K7 J9 J10 K9 K10 H9
D008
A_3.2V AU_2.9V
D_1.2V
V25 PH[2]
PJ[0] T25
MS_PWR_ON
GT6 H6 VFB6 H7 VREF6 G6
CAM_15V
FB303 F7 MSHUT(P/S)
AA5, AB5, Y5
4 IC102 (2/7)
3
AA26 TXD4
SCKO TXDO RXDO PG[7] RST RSTA PG[0]
W23 R26 Y4 AA23
XCS_DD XDD_RST_OUT XPWR_OFF
C6, C5, B6
AB25 RXD4
IC103 BATTERY AUTHENTICATE (2/7)
CD-628 FLEXIBLE BOARD
LED0 B3 LED1 E5 LED2 D4 IC101 XZM_RST_LED XFC_RST_LED XZM_FG_LED D_1.2V L102 A_3.2V IC201 BURST FLASH (4/7) L301 FB301 19 IC202 L201 SDRAM_VCC 256M SDRAM, 64M SUPER AND (4/7) PWR_SAVE 25 CN301 26 CAM_15V CAM_-7.5V Q002 IC001 CCD IMAGER 19 GND IC002 BUFFER
D_3.2V
CAMERA DSP, LENS CONTROL, MODE CONTROL, FRONT CONTROL (2/7)
D_1.8V
VI_3.2V
AU_2.9V D_3.2V L101
05
DSC-W100_L2 3-3E
D_3.2V
L601
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
BT001 LITHIUM BATTERY SP901 SPEAKER
RL-064 FLEXIBLE BOARD
DC-105 FLEXIBLE BOARD
BT901 BATTERY TERMINAL
5
4
J001 DC IN
1
3
ST-146 FLEXIBLE BOARD
1 14 1 15
MC-162 FLEXIBLE BOARD
25 28
CN001 MULTI CONNECTOR
26
LEVEL3 SY-154 BOARD (SIDE B)
CN701
14 1
LEVEL3 SY-154 BOARD (SIDE A)
CN704
14 1 15 1 2
27 1
2
C007 CHARGING CAPACITOR
FLASH UNIT
CN707
14
IC201 (Not supplied)
44 45
CD-628 FLEXIBLE BOARD
1
1
10
1 2
CN708
2
CN601
2 1
10
CN703 MEMORY STICK CONNECTOR
33
MIC901 MICROPHONE UNIT
32
CN301
CN706
1
30
CN401
31
1
45
1
10
LENS BLOCK
1
1
1
33
FP-427 FLEXIBLE BOARD
2
11
12
CONTROL SWITCH BLOCK (SW60610)
33
32
33
CN004
6 1
CN001
CN003
6
38
39
1
D901 BACKLIGHT
2
1
LCD901
CN002
2.5 INCH COLOR LCD MONITOR
1
SW-479 BOARD (SIDE B)
SW-479 BOARD (SIDE A)
DSC-W100_L2 4-1
2
1
14
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-628 FLEXIBLE BOARD (CCD IMAGER) SW-479 BOARD (LCD, CONTROL SWITCH) FP-427 FLEXIBLE BOARD CONTROL SWITCH BLOCK (SW60610) ST-146 FLEXIBLE BOARD (FLASH DRIVE) MC-162 FLEXIBLE BOARD (MULTI CONNECTOR) RL-064 FLEXIBLE BOARD (CONTROL SWITCH) DC-105 FLEXIBLE BOARD (BATTERY IN, DC IN)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-W100_L2
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor External dimensions (mm) Case size · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with 5 differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B Line · J : IN/OUT direction of (+,) B LINE. · C: adjustment for repair. · A: not use circuit (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.) Precautions for Replacement of Imager · If the imager has been replaced, carry out all the adjustments for the camera section. · As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. 1. Connection
Pattern box
Color bar chart Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = 30 cm (PTB-450) L = 12 cm (PTB-1450) Pattern box L Front of the lens Camera
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
Cyan Green
White Magenta
A B
A=B
Fig. a (Video output terminal output waveform) Electronic beam scanning frame CRT picture frame
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
DSC-W100_L2 4-3
Red Blue
B A
1
2
3
4
5
6
7
8
9
10
11
A
CD-628 FLEXIBLE BOARD
CCD IMAGER
XX MARK:NO MOUNT
Note: CD-628 flexible complete board and IC001 are not supplied, but they are included in CCD block assy. Note: Voltage of IC001, IC002 and Q002 can not be measured, because they are mounted by the side of lens.
B
LND045 LND044 LND043 LND042 LND041 LND040 LND039 LND038 LND037
CL001 GND 45 GND 44 GND 43 H2A 42 GND 41 H1A 40 GND 39 CL002 H1B 38 GND 37 H2B 36 GND 35 RG 34 GND 33 GND 32 CCD_GND 31 NC 30 CCD_OUT 29 GND 28 GND 27 3
OUT
CL003
CL007
C
CL011
LND036 LND035 LND034 LND033 LND032 LND031 LND030 LND029
CL014
16 15 14 13 12 11 10
V10 V5B NC V9 V8 V7 V6
9
V5A
8
V4
7
V3B
6
V3A
5
VHLD
4
V2
3
VST
2
NC GND
1
V1 NC
D
SY-154 (1/7)
CN301 Page 4-6 of Level 3
LND028 LND027 LND026 LND025 LND024 LND023 LND022 LND021
2
GND
1
CAM_15V 26 PWR_SAVE 25 GND 24 GND 23 VSUB 22 VSUB_CONT 21 GND 20 CAM_-7.5V 19 GND 18 GND 17 V10 16 V9 15 V8 14 V7 13 V6 12 V5B 11 V5A 10 V4 9 V3B 8 V3A 7 VHLD 6 V2 5 C001 XX R010 220k
IDRV
IC002
BUFFER IC002 CXA3691EN-T9
IC001
CCD IMAGER IC001 ICX476CQZ-13
CSUB VOUT GND GND GND VDD SUB H2B H1B H1A H2A RG NC ISF VL
4
5
VCC
E
LND020 LND019 LND018 LND017 LND016 LND015 LND014
IN
6
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 C008 0.01u C003 XX
C007 0.1u
F
LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005
CL020
CL021
Q002 DTC144EMT2L POWER SAVE SWITCH
R004 470
LND003 LND002 LND001
V1 3 GND 2 GND 1
R005 1k
C002 0.22u
G
LND004
VST 4
C005 0.1u
H
05
DSC-W100_L2 4-5
CD-628
Schematic diagrams of the SY-154 board are not shown. Pages from 4-6 to 4-12 are not shown.
DSC-W100_L2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
FP-427 FLEXIBLE BOARD
PRINTED WIRING BOARD is omitted.
CN001 33P LND034 LND035 LND036 LND037 LND038 LND039 LND040 LND041 LND042 LND043 LND044 LND045 LND046 LND047 LND048 LND049 LND050 LND051 LND052 LND053 LND054 LND055 LND056 LND057 LND058 LND059 LND060 LND061 LND062 LND063 LND064 LND065 LND066 BL_L BL_H XRESET XCS REG_GND SO SI SCLK REG_GND VSYNC HSYNC REG_GND REG_GND DCLK REG_GND REG_GND D7 D6 D5 D4 D3 D2 D1 D0 REG_GND REG_GND REG_GND P_ADJ VDD MODE_DIAL0 MODE_DIAL1 KEY_AD0 KEY_AD1 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 BL_L 1 BL_H 2 XRESET 3 XCS 4 REG_GND 5 SO 6 SI 7 SCLK 8 REG_GND 9 VSYNC 10 HSYNC 11 REG_GND 12 REG_GND 13 DCLK 14 REG_GND 15 REG_GND 16 D7 17 D6 18 D5 19 D4 20 D3 21 D2 22 D1 23 D0 24 REG_GND 25 REG_GND 26 REG_GND 27 P_ADJ 28 VDD 29 MODE_DIAL0 30 MODE_DIAL1 31 KEY_AD0 32 KEY_AD1 33 33 BL_L 32 BL_H 31 XRESET 30 XCS 29 REG_GND 28 SO 27 SI 26 SCLK 25 REG_GND 24 VSYNC 23 HSYNC 22 REG_GND 21 REG_GND 20 DCLK 19 REG_GND 18 REG_GND 17 D7 16 D6 15 D5 14 D4 13 D3 12 D2 11 D1 10 D0 9 REG_GND 8 REG_GND 7 REG_GND 6 P_ADJ 5 VDD 4 MODE_DIAL0 3 MODE_DIAL1 2 KEY_AD0 1 KEY_AD1
SW-479 BOARD
LCD, CONROL SWITCH
XX MARK:NO MOUNT
1 2 3 4 5 6 C013 XX LND005 D007 XX D006 XX LND006 LND007 R007 0 39 38 37 R005 0 C009 XX 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 C005 2.2u R006 56k 20 19 18 17 R064 XX R003 47k ±0.5% C006 2.2u C026 XX C003 2.2u C025 XX C002 2.2u D001 RB520S-30TE61 C004 2.2u D003 XX D002 RB520S-30TE61 C017 XX C010 2.2u C018 XX R004 1M C014 XX C007 2.2u C023 XX C024 XX C001 10u C020 0.01u R001 47k ±0.5% C008 2.2u D004 XX D005 XX C019 XX C011 10u C012 2.2u 16 15 14 13 12 11 10 9 8 7 6 5 4 3 R050 4700 1 2 4 1 3 2 4 R052 4700 2 4 1 3 R054 4700 2 4 1 3 R055 4700 2 4 1 3 C015 XX R010 0 R011 0 C016 XX 2 1 CN002 VCOM TFTCOM NC VSS XRESET XCS SI SCLK VSYNC HSYNC DCLK D7 D6 D5 D4 D3 D2 D1 D0 NC VS VCOMDC VDD VR VCOMH NC VGH VGL C2+ C2C3+ C3COMC VDD2 C1+ C1VSS TFTCOM VCOM LCD901 2.5INCH COLOR LCD MONITOR 39P CN003 BL_L N.C. N.C. N.C. N.C. BL_H 6P D901 BACKLIGHT
B
C
LND009 LND010 LND011 LND012
SY-154 (7/7)
CN708 Page 4-12 of Level 3
LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 LND023 LND024
D
E
LND025 LND026 LND027 LND028 LND029 LND030 LND031
L001 10uH
F
LND032 LND033
IC002 XX R061 XX
1
CE Vout VSS
2
CONTROL SWITCH BLOCK (SW60610)
G
CONTROL SWITCH BLOCK (SW60610) is replaced as block, so that PRINTED WIRING BOARD is omitted.
R115 8200 R114 3600 R113 2200
R062 XX LND004 STATIC_GND 1 D008 XX 1 D009 XX 2 3
3
R116 22000
4 P_AUTO 5 Manual 6
3 AUTO
2 MOVIE
1 Soft snap CN004 6P 6 5 4 3 2 1
S050
3
3
2
4
Vin
R063 XX
S052
S054 (FLASH) R053 4700
S056
S057
H
(SELF TIMER) R051 4700 1 3 2 4
(MACRO)
6 MODE_DIAL0 5
MODE_DIAL0(N.C.)
LND106 LND105 LND104 LND103 LND102 LND101
MODE_DIAL0 MODE_DIAL0(N.C.) REG_GND REG_GND(N.C.) MODE_DIAL1 MODE_DIAL1(N.C.)
IMAGE BRIGHTNESS(EV)
(SET)
4 REG_GND 3 REG_GND(N.C.) ISO 2 MODE_DIAL1 R109 22000 7
Twilight
1 3
2 4
1 3
2 4
8
Twilight portrait
9
Beach
10 Landscape
1
MODE_DIAL1(N.C.)
S051 SCREEN DISPLAY
S053 IMAGE SIZE /DELETE
S055 MENU
I
05
R110 8200
R111 3600
R112 2200
DSC-W100_L2 4-13
SW-479, FP-427, SW60610
· Refer to page 4-3 for mark 0.
1
2
3
4
5
6
7
8
9
10
A
ST-146 FLEXIBLE BOARD
FLASH DRIVE
XX MARK:NO MOUNT NO MARK:REC/PB MODE
L001 2.2uH 2 T002 6 D002 FT02P80TP 1
LND019 XE_H
B
D004 DOR5352 SELF-TIMER/ AF ILLUMINATOR 4 5 3 2 1 4.2
4
C007 145uF 330V CHARGING CAPACITOR 5
R001 1M
LND017 TRIGGER LND018 FLASH UNIT
3
C002 22u 6.3V
TRIGGER_GND C006 0.01u 250V
N.C
N.C
HGND
LND014 LND013 LND012 LND011 LND010
XAF_LED 14 D_3.2V 13 ST_5V 12 ST_UNREG 11 ST_UNREG 10 ST_UNREG 9 5
3
STRB_CHG_CONT 8
VBATT
N.C
C
6
17 16 15 14 13 XE_L LND020 D003 RR255L-400TE25 4.2
1 2
SW SW VCC F_ON
SY-154 (7/7)
LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
IC001
FLASH CONTROL, CHARGE CONTROL IC001 TPS65552RGTR
PGND PGND CHG XFULL
10 11 12
C005 0.047u
0.1 3.2
D
CN704 Page 4-12 of Level 3
0 STRB_ON 7 STRB_CHG 6
4
R004 100k 1/10W C004 0.1u
N.C
REG_GND 3 REG_GND 2 REG_GND 1 C001 XX C003 1u
5 0.1
6
7 0
E
5 6 7 8 R003 33 R002 4.7M 0 1 2 3 4 Q001 CY25BAJ-8F-T23 FLASH DRIVE 266
F
05
DSC-W100_L2 4-14
N.C
REG_GND 4
G_IGBT
I_PEAK
XSTRB_FULL 5
8
9
ST-146
· Refer to page 4-3 for mark 0.
1
2
3
4
5
6
7
1
2
3
4
5
A
MC-162 FLEXIBLE BOARD
MULTI CONNECTOR
XX MARK:NO MOUNT
Note: CN-001(multi connector) is not supplied, but this is included in MC-162 flexible complete board.
CN001 28P (MULTI CONNECTOR) To AV/USB Multi Cable 27
A
DC-105 FLEXIBLE BOARD
BATTERY IN, DC IN
XX MARK:NO MOUNT
2
N.C. N.C.
USB_VBUS USB_GND USB_DP USB_DM USB_GND A_OUT_L A_GND V_OUT V_GND
N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. 28
4
3
1
8
USB_GND 2 USB_DP 3 USB_DM 4 USB_GND 5 AU_LINE_OUT 6 A_GND 7 V_LINE_OUT 8 V_GND 9
XAV_JACK_IN 10
LF001 1 2 3 4
7
B
SY-154 (5/7)
CN706 Page 4-10 of Level 3
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008
USB_VBUS 1
B
6
5
LND001 LND002 LND003 LND004 LND005
ACV_UNREG 1 ACV_UNREG 2 ACV_UNREG 3 ACV_UNREG 4 BATT/XEXT 5 ACV_GND 6 ACV_GND 7 ACV_GND 8 ACV_GND 9 BATT_SIG 10 BATT_UNREG 11 BATT_UNREG 12 BATT_UNREG 13 BATT_UNREG 14 LND016 BATT_UNREG LND017 BATT_SIG LND018 BATT_GND FB002 R001 1k FB001 FB003 1 3 2 5 J001 5P DC IN 4
26 24 22 20 18 16 14 12 10
25 23 21 19 17 15 13 11
9
R004
SY-154 (6/7)
CN701 Page 4-11 of Level 3
LND006 LND007 LND008 LND009
C
LND009 LND010
R005
N.C.
XAV_JACK_IN
C
LND010 LND011 LND012 LND013
1 D001 MAZW068H0LS0
2 3
1
3 2
S
LND014
BT901 BATTERY TERMINAL
STATIC_GND
LND015 STATIC_GND
D
05
D002 MAZW068H0LS0
D003 EDZ TE61 6.8B
D
05
1
2
3
4
5
6
7
A
RL-064 FLEXIBLE BOARD
CONTROL SWITCH
XX MARK:NO MOUNT
LND001 LND002 LND003 VL_3V 1 REG_GND 2
XAE_LOCK_LED 3
BT001 LITHIUM BATTERY D003 SML-412MWT86 (AE/AF LOCK/SELF-TIMER) (GREEN) D001 SML-512WWT86 (FLASH CHARGING/RECORD) (YELLOW) D002 SML-412MWT86 (POWER) (GREEN) SP+ SPLND017
B
SY-154 (7/7)
CN707 Page 4-12 of Level 3
LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012
XSTRB_LED 4 D_3.2V 5 XPWR_LED 6 SP+ 7 XPOWER_ON 8 SP- 9
XAE_LOCK_SW 10 XSHUTTER_SW 11
LND016 SP901 SPEAKER
1 3
2 4
S001 POWER
REG_GND 12 SHUTTER KEY_AD2 13 N.C. 14 XPLAY_SW 15 AE LOCK R001 4700 S005 1 2 S002 (SHUTTER) 4 3
C
LND013 LND014 LND015
D
Note: RL-064 flexible complete board and S002 (shutter) are not supplied, but they are included in cabinet (T) block assy.
S003
W (INDEX)
(ZOOM)
T
1 3
2
S004
4
(PLAYBACK)
3
2
2
3 R002 XX
E
05
1 D004 XX
1 D005 XX D006 XX STATIC_GND LND018
DSC-W100_L2 4-15
MC-162, RL-064, DC-105
4-3. PRINTED WIRING BOARDS
Link
CD-628 FLEXIBLE BOARD SW-479 BOARD ST-146 FLEXIBLE BOARD MC-162 FLEXIBLE BOARD RL-064 FLEXIBLE BOARD DC-105 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
DSC-W100_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
: Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers' patterns are not indicated) · Through hole is omitted. · There are a few cases that the part printed on diagram isn't mounted in this model. · C: panel designation · · · Chip parts. Transistor
C 6 5 4 4 5 6 5 4 4 5
Diode
3 3 3 1 23
B
E
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 2
2 4
1 2 3 3
1 2
1 6 54
4 6 5 4 4 5 6
5 4 3 3 4 5 4
1
1 3
2 2
2
1 1 2 3 3 2 1
4
1
DSC-W100_L2 4-17
CD-628 (2 layers)
: Uses unleaded solder.
CD-628 FLEXIBLE BOARD
45
LND045 LND043 LND041 LND039 LND037 LND035 LND033 LND031 LND029 LND027 LND025 LND023 LND021 LND019 LND017 LND015 LND013 LND011 LND009 LND007 LND005 LND003 LND001 LND044 LND042 LND040 LND038 LND036 LND034 LND032 LND030 LND028 LND026 LND024 LND022 LND020 LND018 LND014 LND012 LND010 LND008 LND006 LND004 LND002 LND016
Note: CD-628 flexible complete board and IC001 are not supplied, but they are included in CCD block assy.
C007
16
15
3
2 1
C001
IC001
3 1
R010
IC002
4 6
C008
C003
17 18 19 31 32
Q002
B
C002
R004
E
C
1
R005
CL020
CL001 CL021
CL007 CL011
C005
CL003
CL002 CL014
05
1-870-222- 11
DSC-W100_L2 4-19
CD-628
Printed wiring boards of the SY-154 board are not shown. Page 4-20 is not shown.
DSC-W100_L2
SW-479 (4 layers)
: Uses unleaded solder.
SW-479 BOARD (SIDE A)
S051 SCREEN DISPLAY
SW-479 BOARD (SIDE B)
3
S051
A
1 3
1
2
4
A
6 1
R053
2
4
R064
D009
3
6
LND005 1
R007
S054
CN003
3
LND006
(FLASH)
S054 2
R054
R005
C009
LND007
R055
D008
R062
R006
B
2
4
CN001
S055 MENU
S055
D006 D007
32
CN004
33
1
1
3
2
B
4
C013
C020
1
2
S052 (MACRO)
S052
38
39
S056
3 4
1
3
3
IMAGE BRIGHTNESS (EV)
C003 CN002
S056
S057
2 2
1
(SET)
1 4
1
2
R063
3 4
D002
C025
R003 C010 C017
R001
C026
R050 R052
3 2
S050
C018
C024
D001
R004 C014
S050
1 2
IC002
1
C
C002
LND004
C023 L001
C006
4
C004 C016
(SELF-TIMER)
4
C
1-870-219- 11
C019
C008
2
1
D003
D005
D004
1-870-219-
11
05
1
2
05
1
2
2
R051
R011
S053 IMAGE SIZE /DELETE
C011
C012
3
C007
C005 C015
C001
S053
R010
1
DSC-W100_L2 4-21
R061
SW-479
ST-146 (2 layers), MC-162 (2 layers)
: Uses unleaded solder.
14
LND014 LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
1
ST-146 FLEXIBLE BOARD
FLASH UNIT
XE_L XE_H
TRIGGER_GND TRIGGER
R002
C007 CHARGING CAPACITOR D003
1
C006
C005
LND020
K
D002
R003
1 2 1
C001
2
8
1
2
C003
8
5
3
Q001
C002
17
13 13
16 16
12
5
13
16
2
1 5
T002
17
4
12
5
1
1
C004
9
4
4
8
9
5
4
1
2
3
4
1
2
IC001
1 6
LND018 LND017
2
L001
1
6
C007
05 10
LND010 LND010 LND009 LND009 LND008 LND008 LND007 LND007 LND006 LND006 LND005 LND005 LND004 LND004 LND003 LND003 LND002 LND002 LND001 LND001
MC-162 FLEXIBLE BOARD
>PI< >PI< >PI<
D003
R005 R004
D001 D002
3 1 4 2 2 3 2 3
LF001
1
1
LND011
26
2
25 28 05 CN001
1 27
(MULTI CONNECTOR)
Note: CN001 (multi connector) is not supplied, but this is included in MC-162 flexible complete board.
DSC-W100_L2 4-22
MCMC162 162 162 162 162 162 162 162 162 162 62 2
1
2 2 2
1
2
R004 2
1 R001 2
A
LND019
D004 SELF-TIMER/ AF ILLUMINATOR
1
1 2
1 2
1 4
8 5
6
2
4
6
4
-
ST-146 >PI<
1
1
D004
3
3
1-870-220- 11
1
1 1 1 1 1 1 1 1 8 0 1 8 0 1 8 70 1 8 70 1 8 70 1 8 70 1-870 1-870 1-8700 0 22 2212211-870-221- 11
ST-146, MC-162
RL-064 (1 layer), DC-105 (2 layers)
: Uses unleaded solder.
RL-064 FLEXIBLE BOARD
1
3
S001 POWER D006
4
1 2 3
RL-064
S005 W (INDEX)
D004 S003 T
S00 3
R001 R002
>PI<
LND018
Note: RL-064 flexible complete board and S002 (shutter) are not supplied, but they are included in cabinet (T) block assy.
K
1 S00
1
D002 (POWER)
2
A
S002
S002 (SHUTTER) D001 FLASH CHARGING/ RECORD
LND017
2
3
4
S00 5
1-870-224- 11
SP-
D005
S004
D001
K A
BT 00 1
2 3 1
SP+
D003
SP901 SPEAKER
+
4
2
1
1-870224-
S004
N
3
LND016
(PLAYBACK)
05
D003 AE/AF LOCK/ SELF-TIMER
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
BT001 BATTERY, LITHIUM SECONDARY
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015
-
S
+
BT901
LND018 LND017 LND016
1
15
DC-105 FLEXIBLE BOARD
DC-105 1-870-223LND015
5
3
FB002 FB001 FB003
R001
05
J001 DC IN
J001
4
1
LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014
1-870-223- 11
1
14
DSC-W100_L2 4-23
RL-064, DC-105
Mounted parts location of the SY-154 board are not shown. Page 4-25 is not shown.
DSC-W100_L2
4-3. PRINTED WIRING BOARDS
4-4. MOUNTED PARTS LOCATION
SW-479 BOARD
* C001 * C002 C003 C004 * C005 C006 * C007 * C008 * C010 C011 C012 * C020 * CN001 CN002 CN003 CN004 D001 D002 * L001 * R001 * R003 R004 * R005 R006 R007 * R010 R011 * R050 * R051 * R052 * R053 * R054 * R055 * * * * * * * * S050 S051 S052 S053 S054 S055 S056 S057 C-1 C-2 C-1 C-1 C-1 C-1 C-2 C-2 C-2 C-1 C-2 B-1 B-1 C-2 B-2 A-1 C-1 C-1 C-1 C-2 C-2 C-1 B-2 B-1 B-2 C-1 C-1 C-1 C-2 C-1 B-2 B-2 B-2 C-1 A-2 B-1 C-2 B-1 A-2 B-2 B-1
no mark : side A * mark : side B
DSC-W100_L2 4-26E
SW-479
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
A
B
C
CABINET SECTION
LCD PANEL SECTION
CABINET (TOP) SECTION
D
E
BT HOLDER SECTION
LENS BLOCK SECTION
Link
CD-628 FLEXIBLE BOARD DC-105 FLEXIBLE BOARD
ELECTRICAL PARTS LIST
E D
ACCESSORIES
E B
MC-162 FLEXIBLE BOARD C RL-064 FLEXIBLE BOARD
C
ST-146 BOARD SW-479 BOARD
DSC-W100_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... · Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
· Color Indication of Appearance Parts Example: (SILVER) : Cabinet's Color (Silver) : Parts Color
· Language that can be selected about SY-154 board
Traditional Chinese Arabic Dutch Russian Swedish Korean Norwegian Danish Finnish Polish Hungarian Czech
z z z z z z z z z z z z z
Japanese English French German Spanish Italian Portugal Simplified Chinese
GP1 GP2
GP3
GP4
J US CND AUS Vietnam AEP UK E AR BR TW JE HK CH KR
z
z z
z z
z
z z z z z z
z
z
z
z
z z
DSC-W100_L2 5-1
Persian Thai
Area
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. CABINET SECTION
ns: not supplied
DISASSEMBLY
HARDWARE LIST
5
6
LCD Panel Section (See page 5-3)
4 3
#26 (SILVER) #27 (BLACK) #20 (SILVER) #21 (BLACK)
#20 (SILVER) #21 (BLACK)
2
#20 (SILVER) #21 (BLACK)
1
ns #20 (SILVER) #21 (BLACK) #20 (SILVER) #21 (BLACK)
Ref. No. 1 1 2 3 3 4 4
Part No. X-2109-132-1 X-2109-133-1 2-676-233-01 2-676-269-01 2-676-269-11
Description CABINET (F) ASSY (S) (SILVER) CABINET (F) ASSY (B) (BLACK) SCREW, TRIPOD CABINET (L) (SILVER) CABINET (L) (BLACK)
Ref. No. 5 5 6 #20 #21 #26 #27
Part No.
Description
X-2109-134-1 CABINET (B) ASSY (S) (SILVER) X-2109-135-1 CABINET (B) ASSY (B) (BLACK) 2-676-274-01 WINDOW, LCD 2-635-591-31 2-662-396-21 2-635-591-11 2-662-396-11 SCREW (M1.4), NEW TRUSTAR P2 (Silver) SCREW (M1.4), NEW, TRUSTAR, P2 (Black) SCREW (M1.4), NEW TRUSTAR P2 (Silver) SCREW (M1.4), NEW, TRUSTAR, P2 (Black)
2-671-731-01 KEY, CURSOR (SILVER) 2-671-731-11 KEY, CURSOR (BLACK)
DSC-W100_L2 5-2
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-2. LCD PANEL SECTION
HARDWARE LIST
52 53
#3
SW-479
LCD901
#3
51
D901 Cabinet (Top) Section (See page 5-4)
Ref. No. 51 51 * 52 53
Part No. 1-479-668-11 1-479-668-21 1-870-217-11 A-1178-792-A
Description CONTROL SW BLOCK (SW60610) (SILVER) CONTROL SW BLOCK (SW60610) (BLACK) FP-427 FLEXIBLE BOARD SW-479 BOARD, COMPLETE
Ref. No. D901
Part No.
Description
1-479-623-11 BLOCK, LIGHT GUIDE PLATE (2.5)
LCD901 A-1185-814-A LCD SUB BLOCK ASSY #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
DSC-W100_L2 5-3
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-3. CABINET (TOP) SECTION
ns: not supplied
102
(including RL-064 flexible board)
101
ns
103
BT001 SP901
106
(Size: 5mm x 5mm) BT Holder Section (See page 5-5)
104
105
! : Board on the mountLITHIUM SECONDARY) BT001 (BATTERY, position.
(See page 4-23.) Lens Block Section (See page 5-6)
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Note: For the part of 106: SHEET (55), ADHESIVE (2-685267-01), cut SHEET, ADHESIVE (2-649-300-01) into the desired length and use it.
· Refer to page 5-1 for mark 0. Ref. No. 101 101 102 102 103 103 Part No. Description Ref. No. 104 * 105 * 105 106 0 BT001 SP901
Part No. A-1178-824-A 2-676-273-01 2-676-273-11 Note
Description MC-162 FLEXIBLE BOARD, COMPLETE HOLDER, CAPACITOR (SILVER) HOLDER, CAPACITOR (BLACK) SHEET, ADHESIVE
X-2109-136-1 LID ASSY (S), DC (SILVER) X-2109-137-1 LID ASSY (B), DC (BLACK) A-1178-698-A CABINET (T) BLOCK ASSY (S) (including RL-064 flexible board) (SILVER) A-1178-699-A CABINET (T) BLOCK ASSY (B) (including RL-064 flexible board) (BLACK) 2-676-268-01 CABINET (R) (SILVER) 2-676-268-11 CABINET (R) (BLACK)
1-756-539-11 BATTERY, LITHIUM SECONDARY 1-826-403-11 LOUD SPEAKER (1.0CM)
DSC-W100_L2 5-4
MC-162
5. REPAIR PARTS LIST
DISASSEMBLY
5-1-4. BT HOLDER SECTION
ns: not supplied
HARDWARE LIST
155
157
BT901
154
156
#5
05 -1 C D
ns
E (Middle east, Gulf)
159 158
#3
SY -15 4
MIC901
153
151
152
* Refer to the table of page 5-1 about language of SY-154 board. · Refer to page 5-1 for mark 0. Ref. No. 151 151 151 152 152 153 0 154 * 155 * 156 Part No. A-1185-818-A A-1187-402-A A-1187-403-A 2-676-216-01 2-676-216-11 X-2109-613-1 A-1178-825-A 2-676-266-01 2-676-267-01 Description SY-154 BOARD, COMPLETE (SERVICE) (GP2) SY-154 BOARD, COMPLETE (SERVICE) (GP3) SY-154 BOARD, COMPLETE (SERVICE) (GP4) LID, BT (SILVER) LID, BT (BLACK) ASSY, BTH PRE DC-105 FLEXIBLE BOARD, COMPLETE SUPPORT, DC FLEXIBLE FRAME, MAIN Ref. No. * 157 * 158 * 159 0 BT901 MIC901 #3 #5 Part No. Description
2-676-272-01 SUPPORT, SW 2-676-276-01 2-687-368-01 1-780-061-21 1-542-691-11 SHEET, LCD INSULATING LABEL, FUSE RATING BATTERY TERMINAL BOARD MICROPHONE BLOCK
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) 3-080-204-01 SCREW, TAPPING, P2 (Black)
DSC-W100_L2 5-5
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-5. LENS BLOCK SECTION
ns: not supplied
211 212
ST -14
6
ns
209 210
208
(including IC001 (CCD imager) and CD-628 flexible complete board) (Note 1, 2) #28 #5
206 201
(Note 3) ns
207
205 213
204
(Note 3)
203
(Note 3)
202
(Note 3)
Note 1: CCD block assembly is including CD-628 flexible complete board. Note 2: Be sure to read "Precuations for Replacement of Imager" on page 4-3. Note 3: Be sure to read "Exchange method of barrier assy" on page 2-6.
· Refer to page 5-1 for mark 0. Ref. No. 201 202 203 204 205 206 207 208 Part No. A-1060-696-A 3-091-427-01 X-3954-476-1 3-086-156-31 2-021-317-01 Description LENS BLOCK ASSY 890 (J1) (Note 3) RING (A), ORNAMENTAL (Note 3) BARRIER ASSY (Note 3) TAPPING SCREW (P2) (Note 3) MASK, LPF Ref. No. 0 209 0 210 * 211 * 212 * 213 #5 #28 Part No. Description
A-1178-823-A ST-146 FLEXIBLE BOARD, COMPLETE 1-479-690-11 FLASH UNIT 2-676-271-01 HOLDER, AF 2-676-270-01 HOLDER, ST X-2109-138-1 FRAME ASSY, LENS 3-080-204-01 SCREW, TAPPING, P2 (Black) 3-348-998-61 SCREW (M1.4X4), TAPPING, PAN (Dark Silver)
1-788-391-11 OPTICAL FILTER BLOCK (OFB-02-27) 2-021-318-01 SEALGOM 890 A-1178-700-A CCD BLOCK ASSY (including IC001 (CCD IMAGER) and CD-628 flexible complete board) (Note 1, 2)
DSC-W100_L2 5-6
CD-628
5-2. ELECTRICAL PARTS LIST
Ref. No. Part No. Description
DC-105
Ref. No. Part No.
MC-162
Description
RL-064
ST-146
A-1178-700-A CCD BLOCK ASSY (Note 1) (Not supplied) CD-628 FLEXIBLE BOARD, COMPLETE ******************************* (CD-628 flexible complete board and IC001 are not supplied, but they are included in CCD block assy.) < CAPACITOR > C002 C005 C007 C008 1-127-715-91 1-125-777-11 1-100-505-91 1-164-943-81 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < IC > IC001 IC002 (Not supplied) ICX476CQZ-13 (Note 1) 8-753-230-85 IC CXA3691EN-T9 < TRANSISTOR > 0.22uF 0.1uF 0.1uF 0.01uF 10% 10% 20% 10% 16V 10V 16V 16V
< LINE FILTER > LF001 1-456-583-21 COMMON MODE CHOKE COIL < RESISTOR > R004 R005 1-500-283-11 INDUCTOR, FERRITE BEAD (Note 2) 1-500-283-11 INDUCTOR, FERRITE BEAD (Note 2)
A-1178-698-A CABINET (T) BLOCK ASSY (S) (SILVER) A-1178-699-A CABINET (T) BLOCK ASSY (B) (BLACK) (Not supplied) RL-064 FLEXIBLE BOARD, COMPLETE ******************************* (RL-064 flexible complete board and S002 (shutter) are not supplied, but they are included in cabinet (T) block assy.) < SPEAKER > SP901 1-826-403-11 LOUD SPEAKER (1.0CM) < BATTERY >
Q002
6-550-119-01 TRANSISTOR < RESISTOR >
DTC144EMT2L
0 BT001 R004 R005 R010 1-218-949-11 RES-CHIP 1-218-953-11 RES-CHIP 1-218-981-11 RES-CHIP 470 1K 220K 5% 5% 5% 1/16W 1/16W 1/16W D001 0 A-1178-825-A DC-105 FLEXIBLE BOARD, COMPLETE ******************************* < BATTERY TERMINAL > D002 D003
1-756-539-11 BATTERY, LITHIUM SECONDARY < DIODE > 6-500-252-01 DIODE SML-512WWT86 (FLASH CHARGING/RECORD) 6-501-030-01 DIODE SML-412MWT86 (POWER) 6-501-030-01 DIODE SML-412MWT86 (AE/AF LOCK/SELF-TIMER) < RESISTOR >
0 BT901
1-780-061-21 BATTERY TERMINAL BOARD R001 < FERRITE BEAD > < SWITCH > 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
FB001 0 FB002 0 FB003
1-414-228-11 INDUCTOR, FERRITE BEAD 1-469-324-21 FERRITE, EMI (SMD) (2012) 1-469-324-21 FERRITE, EMI (SMD) (2012) < JACK >
S001 S002 S003 S004 S005
1-786-157-31 (Not supplied) 1-786-179-31 1-786-157-11 1-786-180-31
TACTILE SWITCH (POWER) TACTILE SWITCH (SHUTTER) SWITCH, PUSH (1KEY) (T (ZOOM)) SWITCH, TACTILE (N (PLAYBACK)) SWITCH, PUSH (1KEY) (W (ZOOM)/INDEX)
0 J001
1-817-331-11 DC JACK 5P (DC IN) < RESISTOR > 0 1K 5% 1/10W 0 A-1178-824-A MC-162 FLEXIBLE BOARD, COMPLETE ******************************* (CN001 (multi connector) is not supplied, but this is included in MC-162 flexible complete board.) < CONNECTOR > 1-479-690-11 FLASH UNIT < CAPACITOR > C002 C003 C004 0 C005 1-100-611-91 1-100-506-91 1-125-777-11 1-100-758-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22uF 1uF 0.1uF 0.047uF 20% 20% 10% 10% 6.3V 6.3V 10V 250V A-1178-823-A ST-146 FLEXIBLE BOARD, COMPLETE *******************************
R001
1-216-821-11 METAL CHIP
CN001
(Not supplied) CONNECTOR, MULTIPLE (SOCKET) < DIODE >
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Note 1: Be sure to read "Precautions for Replacement of Imager" on page 4-3 when changing the imager. Note 2: Ferrite beads are mounted to the location where R004 and R005 are printed.
D001 D002 D003
6-500-776-01 DIODE MAZW068H0LS0 6-500-776-01 DIODE MAZW068H0LS0 8-719-083-91 DIODE EDZ TE61 6.8B
· Refer to page 5-1 for mark 0.
DSC-W100_L2 5-7
ST-146
Ref. No. C006 0* C007
SW-479
Description 0.01uF 145uF 10% 250V < RESISTOR > 330V R001 R003 R004 R005 R006 R007 R010 R011 R050 R051 R052 R053 R054 R055 1-208-927-11 1-208-927-11 1-218-989-11 1-218-990-81 1-218-974-11 1-218-990-81 1-218-990-81 1-218-990-81 1-218-961-11 1-218-961-11 1-218-961-11 1-218-961-11 1-218-961-11 1-218-961-11 METAL CHIP METAL CHIP RES-CHIP SHORT CHIP RES-CHIP SHORT CHIP SHORT CHIP SHORT CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP < SWITCH > S050 S051 S052 S053 S054 S055 S056 S057 1-786-157-31 1-786-157-31 1-786-157-31 1-786-157-31 1-786-157-31 TACTILE SWITCH (V (SELF-TIMER)) TACTILE SWITCH (SCREEN DISPLAY) TACTILE SWITCH (B (MACRO)) TACTILE SWITCH (IMAGE SIZE/DELETE) TACTILE SWITCH (v (FLASH)) 47K 47K 1M 0 56K 0 0 0 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 0.5% 0.5% 5% 5% 1/16W 1/16W 1/16W 1/16W Ref. No. Part No. Description
Part No.
1-100-761-21 CERAMIC CHIP 1-114-120-11 CAP, ELECT
0 D002 0 D003 * D004
< DIODE > 6-501-141-01 DIODE FT02P80TP 6-500-811-01 DIODE RR255L-400TE25 6-501-364-01 DIODE DOR5352 (SELF-TIMER/AF ILLUMINATOR) < IC >
IC001
6-707-555-01 IC TPS65552RGTR < COIL >
5% 5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
* L001
1-400-820-11 INDUCTOR < TRANSISTOR >
2.2uH
0 Q001
6-550-656-01 TRANSISTOR < RESISTOR >
CY25BAJ-8F-T23
0 R001 R002 R003 R004
1-216-121-11 1-243-975-11 1-218-935-11 1-216-097-11
RES-CHIP METAL CHIP RES-CHIP RES-CHIP
1M 4.7M 33 100K
5% 5% 5% 5%
1/10W 1/16W 1/16W 1/10W
< TRANSFORMER > 0 T002 1-443-568-21 TRANSFORMER, D.C.-D.C.CONVERTER
1-786-157-31 TACTILE SWITCH (MENU) 1-786-157-31 TACTILE SWITCH (b (IMAGE BRIGHTNESS (EV))) 1-786-157-31 TACTILE SWITCH (z (SET))
A-1178-792-A SW-479 BOARD, COMPLETE *********************** < CAPACITOR > C001 C002 C003 C004 C005 C006 C007 C008 C010 C011 C012 C020 1-137-710-11 1-100-743-91 1-100-743-91 1-100-743-91 1-100-743-91 1-100-743-91 1-100-743-91 1-100-743-91 1-100-743-91 1-137-710-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 10uF 2.2uF 0.01uF 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 10% 6.3V 16V 16V 16V 16V 16V 16V 16V 16V 6.3V 16V 16V
Electrical parts list of the SY-154 board is not shown. Pages 5-9 to 5-11 are not shown.
1-112-021-91 CERAMIC CHIP 1-164-943-81 CERAMIC CHIP < CONNECTOR >
* CN001 CN002 * CN003 * CN004
1-817-564-51 1-817-544-51 1-816-654-51 1-816-654-51
CONNECTOR, FPC (ZIF) 33P CONNECTOR, FPC (ZIF) 39P FFC/FPC CONNECTOR (LIF) 6P FFC/FPC CONNECTOR (LIF) 6P < DIODE >
D001 D002
8-719-069-29 DIODE RB520S-30TE61 8-719-069-29 DIODE RB520S-30TE61 < COIL >
L001
1-400-588-11 INDUCTOR, LAMINATE CHIP 10uH
· Refer to page 5-1 for mark 0.
DSC-W100_L2 5-8
Checking supplied accessories. Other accessories
2-674-774-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP, UK, E, HK, AUS, JE) 2-674-774-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (AEP) 2-674-774-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, JE) 2-674-774-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP) 2-674-774-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-674-774-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN) (AEP) 2-674-774-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-674-774-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-674-774-91 INSTRUCTION (READ THIS FIRST) (CZECH, POLISH) (AEP) 2-674-775-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAK) (AEP) 2-674-775-21 INSTRUCTION (READ THIS FIRST) (SWEDISH, FINNISH) (AEP) 2-674-775-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN, DANISH) (AEP) 2-674-776-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US, CND) 2-674-776-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND) 2-674-788-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT KR, CH) 2-674-788-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (CND, AEP) 2-674-788-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, JE) 2-674-788-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) (AEP) 2-674-788-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-674-788-61 2-674-788-71 2-674-788-81 2-674-788-91 2-674-790-11 INSTRUCTION (USER'S GUIDE) (RUSSIAN) (AEP) INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E) INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE) INSTRUCTION (USER'S GUIDE) (CZECH, POLISH) (AEP) INSTRUCTION (USER'S GUIDE) (HUNGARIAN, SLOVAK) (AEP)
Battery Charger BC-CSG 0 1-479-583-21 (US, CND)
Battery Charger BC-CSG 0 1-479-583-31 (EXCEPT US, CND)
USB, A/V Cable for Multiuse Terminal 1-829-866-41
Power Cord 0 1-555-074-71 (AUS) 0 1-782-476-41 (CH) 0 1-783-374-22 (HK) 0 1-792-549-31 (JE) 0 1-823-947-51 (KR) 0 1-824-910-31 (AEP, E) 0 1-827-269-22 (UK)
Rechargeable Battery Pack NP-BG1 (not supplied)
Battery Case (not supplied)
Wrist Strap 2-050-981-01
CD-ROM (Cyber-shot Application Software) 2-666-673-01
Conversion (2P) Adaptor 0 1-569-007-12 (JE)
Conversion (2P) Adaptor 0 1-569-008-12 (E)
2-674-790-21 INSTRUCTION (USER'S GUIDE) (SWEDISH, FINNISH) (AEP) 2-674-790-31 INSTRUCTION (USER'S GUIDE) (NORWEGIAN, DANISH) (AEP) · Refer to the page 5-1 for mark 0.
DSC-W100_L2 5-12E
DSC-W100
LEVEL
2
SERVICE MANUAL
Ver 1.1 2006.07
SUPPLEMENT-1
File this supplement with the service manual.
(DI06-024)
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Brazilian Model Tourist Model
· Addition of LCD Type (TYPE SA) · Addition and Change of Repair Parts
Link
SERVICE NOTE BLOCK DIAGRAMS SCHEMATIC DIAGRAMS REPAIR PARTS LIST
· Along with TYPE SH, TYPE SA is added at type of LCD. · For ADJUSTMENTS of LCD, refer to the SERVICE MANUAL, ADJ SUPPLEMENT-1 (9-876-941-82). · When the machine needs to be repaired, make sure to follow the item of "LCD TYPE CHECK". · A combination of LCD (LCD901) and SW-479 board varies depending on the type of LCD panel (see the following table). Normal display will not be attained unless correct LCD (LCD901), SW-479 board, and adjustment data are combined respectively. Readjustment is required if LCD (LCD901) or SW-479 board is changed. Combination table
LCD TYPE TYPE S