Text preview for : PANASONIC SA-AK177.pdf part of PANASONIC SA-AK177 S.M.
Back to : PANASONIC SA-AK177.part1 | Home
ORDER NO. MD0105111C3
CD Stereo System
SA-AK177
Colour (S)... Silver Type Area (GC)...Asia, Latin America, Africa and Middle Near East TAPE SECTION : AR2 MECHANISM SERIES CD SECTION : RAE0152Z-3 TRAVERSE DECK SERIES
1
2005-05-13
SPECIFICATIONS
Specifications
AMPLIFIER SECTION PMPO RMS power output THD 10%, both channels driven Front 80 Hz (Low channel) Front 1 kHz (High channel) Center 1 kHz Surround 1 kHz Total power output in Dolby Pro Logic mode RMS power output THD 10%, both channels driven 80 Hz (Low channel) 1 kHz (High channel) Total power output in stereo mode Input sensitivity AUX MIC Input Impedance AUX MIC FM TUNER SECTION Frequency range Sensitivity S/N 26 dB Antenna terminal(s) AM TUNER SECTION Frequency range 75 3000 W
75 W per channel (8 40 W per channel (8
) )
100 W (8 ) 35 W per channel (8 ) 400 W
) 75 W per channel (8 40 W per channel (8 ) 115 W
250 mV 0.7 mV 13 k 680 87.50 - 108.00 MHz (50 kHz steps) 2.5 V (IHF) V 2.2 (unbalanced)
522 - 1629 kHz (9 kHz steps) 520 - 1630 kHz (10 kHz steps)
Sensitivity S/N 20 dB (at 999 kHz) CASSETTE DECK SECTION
560
V/m
2
2005-05-13
Track system Heads Record/playback Erasure Motor Recording system Erasing system Tape speed
4 track, 2 channel Solid permalloy head Double gap ferrite head DC servo motor AC bias 100 kHz AC erase 100 kHz
4.8 cm/s Frequency response (+3 dB, -6 dB at DECK OUT) NORMAL (TYPE I) 35 Hz - 14 kHz HIGH (TYPE II) S/N 35 Hz - 14 kHz 50 dB (A weighted) 0.18% (WRMS) Approx. 120 seconds with C-60 cassette tape
Wow and flutter Fast forward and rewind time CD SECTION Sampling frequency Decoding
44.1 kHz
16 bit linear Beam source/wave length Semiconductor laser/780 nm Number of channels Stereo Frequency response Wow and flutter Digital filter D/A converter Video CD Video data Audio data Video output Video format Output voltage Physical format GENERAL Power supply Power consumption Power consumption in standby mode 0.9 W Dimensions (W x H x D) Mass SYSTEM SC-AK177 (GC) 250 x 332 x 319 mm 9.0 kg Music Center: SA-AK177 (GC) Speaker: SB-AK77 (GC)
3 2005-05-13
20 Hz - 20 kHz (+1, -2 dB) Below measurable limit 8 fs MASH (1 bit DAC) Based on MPEG 1 Based on MPEG 1 Layer 2 NTSC/PAL 1 Vp-p, 75 k Based on CD-ROM format AC 110 V/127 V/220-230 V /240V, 50/60 Hz 150 W
Speaker: SB-AK77 (GC) Center speaker: SBPC70A (GC) Surround speaker: SBPS70A (GC) Notes:
1. Specifications are subject to change without notice. Weight and dimensions are approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. 3. HIGH stands for High Frequency. LOW stands for Low Frequency.
1
1. Before Use
Be sure to disconnect the mains cord before adjusting the voltage selector. Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will be used. (If the power supply in your area is 117V or 120V, set to the "127V" position.) Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries, the correct voltage is already set.)
2. Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C572, C584-C587 through a 10 , 5W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent. Current consumption at AC 110V, 50Hz and AC 240V, 50Hz in NO SIGNAL mode should be ~600 mA.
4
2005-05-13
3. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
- No sound is heard when the power is turned on. - Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are "shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used. If this occurs, follow the procedure outlines below: 1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power once again after one minute. Note: When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
4. Accessories
Remote Control Transmitter
FM indoor antenna
AC mains lead
5
2005-05-13
AM Loop antenna
Power plug adapter
6
2005-05-13
Video connection cable
5. Handling Precautions For Traverse Deck
The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
- Handling of traverse deck (optical pickup)
1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock. 2. The short land between the No.4(LD) and No.5(GND) pins on the flexible board (FFC) is shorted with a solder build-up to prevent damage to the laser diode.To connect to the PC board, be sure to open by removing the solder build-up, and finish the work quickly. 3. Take care not to apply excessive stress to the flexible board (FFC). 4. Do not turn the variable resistor (laser power adjustment). It has already been adjusted.
7
2005-05-13
- Grounding for electrostatic breakdown prevention
1. Human body grounding Use the anti-static wrist strap to discharge the static electricity from your body. 2. Work table grounding Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is placed, and ground the sheet.
Caution :
The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the traverse deck (optical pickup).
Caution when Replacing the Traverse Deck :
The traverse deck has a short point shorted with solder to protect the laser diode against electrostatics breakdown. Be sure to remove the solder from the
8
2005-05-13
short point before making connections.
6. Precaution of Laser Diode
Caution :
This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens. Wavelength : 780 nm Maximum output radiation power from pick up : 100 W/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous. 2. Do not adjust the variable resistor on the pick up unit. It was already adjusted. 3. Do not look at the focus lens using optical instruments. 4. Recommend not to look at pick up lens for a long time.
ACHTUNG :
Dieses Produkt enthält eine Laserdiode. Im eingeschalteten Zustand wird unsichtbare Laserstrahlung von der Lasereinheit abgestrahlt. Wellenlänge : 780nm W/VDE Maximale Strahlungsleistung der Lasereinheit :100 Die Strahlung an der Lasereinheit ist ungefährlich, wenn folgende Punkte beachtet werden: 1. Die Lasereinheit nicht zerlegen, da die Strahlung an der freigelegten Laserdiode gefährlich ist. 2. Den werkseitig justierten Einstellregler der Lasereinhit nicht verstellen.
9
2005-05-13
3. Nicht mit optischen Instrumenten in die Fokussierlinse blicken. 4. Nicht über längere Zeit in die Fokussierlinse blicken.
ADVARSEL: I dette a apparat anvendes laser. CAUTION!
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Use of Caution Labels
10
2005-05-13
7. Operation Procedures
11
2005-05-13
12
2005-05-13
8. Disassembly and Main Component Replacement Procedures
13
2005-05-13
"ATTENTION SERVICER" Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. 2. For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required. 3. Select items from the following index when checks or replacement are required. Contents
- Disassembly and assembly main unit
1. Checking of the Main, VCD, Panel, Deck and Power P.C.B.
- Main Component Replacement Procedures
1. Replacement of the Traverse Deck. 2. Replacement of the Power Amplifier IC.
- Disassembly and assembly of the Traverse Unit - Disassembly and assembly of the Disc Tray
Warning:
This product uses a laser diode. Refer to caution statement Precaution of Laser
14 2005-05-13
Diode.
ACHTUNG:
Die Lasereinheit nicht zerlegen. Die Lasereinheit darf nur gegen eine vom Hertsteller spezifizierte Einheit ausgetauscht werden.
8.1. Disassembly Procedure For Each Major P.C.B. Checking
8.1.1. Checking of the Main, VCD, Transformer, Panel and Deck P.C.B.
Step 2 Remove the top cabinet. Step 3 Remove the T-bracket.
15
2005-05-13
16
2005-05-13
Step 5 Turn locating pin on both sides 90°. (Locating pin need not to be bent back.)
17
2005-05-13
Step 6 Release the Main P.C.B. connectors CN305,CP402, CP403, CN204, CN205, CP400,and VCD P.C.B. connectors CN802, CN 803. Remove rear panel by pulling it backward and lift the rear panel assembly.
18
2005-05-13
Step 7 Use a hexagonal wrench and turn clockwise to release the tray.
19
2005-05-13
Step 8 Pull the CD tray in the direction shown above.
20
2005-05-13
Step 9 Remove the CD lid in the direction of the arrow.
21
2005-05-13
Step 11 Release the two catches shown above to remove the front cabinet from the CD traverse unit.
22
2005-05-13
Step 12 Connect back the wire to CN302, CN303 and CN304. Use the extension wire (REXX0261) to connect to CN502. Use a FFC wire (REEX0137) to connect CN1 to CN309.
8.1.2. Checking for Panel, Main and Deck P.C.B.
23
2005-05-13
24
2005-05-13
Step 1 Remove 2 screws each side.
8.1.3. Checking for Power P.C.B.
25
2005-05-13
8.2. Main Component Replacement Procedures
1. Replacement of the Traverse Deck Step 1 Follow the procedures in `Disassembly of the Traverse Unit' ( Step 1 Step 4 )
26
2005-05-13
Step 3 Desolder the 4 legs of the 2 motors and pull out the Servo P.C.B. Step 4 Widen the 3 bosses with a flat screwdriver and pull out the 3 pins. Then remove the Traverse Deck.
27
2005-05-13
Step 5 Remove the flexible cable CN 701.
- Removal of the flexible cable. Push the top of the connector in the direction of
the arrow 1, and then pull out the flexible cable in the direction of the arrow 2. Note: Insert a short pin into the flexible cable for traverse unit.
- Installation of the CD servo P.C.B. after replacement
Step 1 Connect the FFC board. Step 2 Install the CD servo P.C.B. in the traverse deck assembly.
28
2005-05-13
Note: Before installing the CD servo P.C.B., move the optical pickup towards the outer edge from the marking (black triangle). [Otherwise, the reset detect switch (S701) mounted on the CD servo P.C.B. may be damaged.]
29
2005-05-13
2. Replacement of the Power Amplifier IC Step 1 Follow the procedures in `Checking Procedure for each major P.C.B.' ( Step 1 - Step 4 ).
Step 2 Remove the wires at CP400 and CP401 and pull out the Main P.C.B. Step 3 Remove 4 screws fixed to the Power Amplifier IC.
30
2005-05-13
Step 4 Unsolder the terminals of Power Amp IC and replace the respective component.
31
2005-05-13
8.3. Disassembly and assembly of the Traverse Unit
Step 1 Push the lever from position A to B. Step 2 Pull the stopper (black) in the direction of arrow 1 and push the lever in the direction of arrow 2. Step 3 Push the stpeer (black) down until the white lever eject out.
32
2005-05-13
Step 4 Lift up the traverse unit and slide out the unit as shown.
- Replacement of Traverse Unit
33
2005-05-13
Step 1 Place the traverse unit as shown. Step 2 Press in the lever shaft in the direction of arrow 1 as shown and push the traverse unit into the position in the direction of arrow 2.
Step 3 Pull the stopper in the direction of arrow 1 and release the lever in the direction of arrow 2 as shown.
34
2005-05-13
Step 4 Pull out the tray half way and push it back fully.
Step 5 Push the lever to the initial position indicated `I---I'.
8.4. Disassembly and assembly of the Disc Tray
35
2005-05-13
Step 2 With lifting the claw in the direction of arrow 1, draw the clamp SW P.C.B. in the direction of arrow 2. Step 3 Remove the mechanism cover.
36
2005-05-13
Step 4 Insert the gear with hexagonal wrench into the hole.
37
2005-05-13
Step 5 Rotate the hexagonal wrench in the direction of arrow (clockwise), and then open the disc tray fully.
38
2005-05-13
Step 6 Upset the CD changer unit again. Step 7 Release both the claws, and then draw the disc tray.
39
2005-05-13
Step 8 With forcing the left guide bar manually because the left guide bar interfers with claw, draw the disc tray.
- Installation of the disc tray after replacement
40
2005-05-13
Step 1 Slide the drive rack fully in the direction of arrow.
41
2005-05-13
42
2005-05-13
Step 2 Holding the drive rack not to move, install the disc tray.
Step 3 Align the drive rack with the driver gear.
43
2005-05-13
Step 4 Holding the disc tray manually, rotate the pulley gear in the direction of arrow. Step 5 Rotate the gear 5 or 6 times manually, and then push the disc tray.
9. Self-Diagnostic Function
9.1. Self-diagnostic display
This unit is equipped with a self-diagnostic display function which, if a problem occurs, will display an error code corresponding to the problem. Use this function when performing maintenance on the unit.
9.2. How to enter the Self-Diagnostic Function
44
2005-05-13
9.3. Cassette Mechanism Test (For error code H01, H02, H03, F01, F02)
1. Press "TAPE, DECK 1/2" to select Deck 2. 2. Load a cassette tape with the erasure prevention tab, remove from left side only and close the cassette holder. 3. Press "FAST FORWARD MEMORY" (Tape will be stop after 2 seconds) 4. Load a cassette tape with the erasure prevention tab, remove from right side only and close the cassette holder. 5. Press "REVERSE FM MODE/BP" (Tape will be stop after 2 seconds) 6. Load a pre-recorded tape with both side record tabs intact and close the cassette holder. 7. Press "PLAY/TUNE/TIME ADJ UP" (After TPS function, tape will stop
45
2005-05-13
automatically) 8. Press "REC/STOP" (Tape will not move) 9. Press "STOP/TUNE MODE" to indicate Error code. - If several problem exist, error code will change each time when " TUNE MODE" is pressed. (e.g. H01 H03 F01 .....etc.) 10. Press "TAPE, DECK 1/2" to select Deck 1. 11. Repeat step 2 to 9 to test Deck 1. (Tape Deck 1 will not check H02 because of no recording function) /
9.4. CD Mechanism Test (F15, F26, F16, F17, F27, F28, F29, H15)
1. Press "CD". 2. Press "OPEN/CLOSE (1)" and place a CD. 3. Press "OPEN/CLOSE (1)" to close the tray. 4. Press "OPEN/CLOSE (5)" and wait until the tray is open. 5. Press "OPEN/CLOSE (1)" and remove the CD. 6. Press "OPEN/CLOSE (1)" to close the tray. 7. Press " /TUNE MODE" to indicate Error Code. /
- If several problem exist, error code will change each time when " TUNE MODE" is pressed. (e.g. F15 F26 F16 ....etc).
9.5. To clear all Error code
1. Press "STOP/TUNE MODE" button for 5 seconds. 2. FL indicator shows "CLEAR" for 1 second and change to "T".
9.6. How to get out from Self-Diagnostic function
1. Press "Power" button OFF.
9.7. Power Amplifier Failure (F61)
1. When power amplifier fail, F61 will indicate automatically.
46
2005-05-13
10. Description of Error Code
10.1. Error detection for Cassette Mechanism block
No. 1 Error MODE SW detection error REC INH SW detection error HALF SW detection error Reel Pulse detection error TPS abnormal Error Problem condition Display H01 Faulty operation of cassette mechanism. Faulty contact or short-circuit of mechanism mode switch (S951, S971). H02 Recording not possible. Faulty contact or short-circuit of REC INH switch (S974, S975). H03 Playback cannot perform. Faulty contact or short-circuit of HALF siwtch (S952, S972). F01 The tape advances slightly and then stops. Faulty reel pulse, faulty hole detect IC (IC951, IC971). F02 Cassette deck will not perform TPS function. Faulty playback EQ/recording amplifier IC (IC101).
2
3
4 5
10.2. Error detection for CD/Changer block
No. 1 Error REST SW detection error Error Problem condition Display F15 CD does not function. This error occurs when the Optical Pick Up REST SW (S701) is not detected within the specified time (about 8 seconds) F16 CLAMP switch (S4) NG (Check & Replace) F17 BOTTOM switch (S5) NG (Check & Replace)
2 3
4
CD tray opens automatically Does not startup when [PLAY] button is pressed Transmission error between CD servo LSI and micon Startup fails even when you insert CD or the selected disc tray does not open Cannot insert CD
F26
5
F27
CD does not function. This error occurs when the POWER is ON for the CD block and an error is detected after the transmission has started. Tray 1 detect switch or Tray 2 detect switch NG (Check & Replace)
6
F28
Tray 1 detect switch NG (Check & Replace)
47
2005-05-13
No. 7 8
Error Cannot eject CD The CD tray closes
Error Problem condition Display F29 Check if disc is stuck. Tray 2 detect switch NG (Confirm & Replace) H15 CD disc tray detect switch NG (S3) (Check & Replace)
10.3. Power Supply related error detection
No. 1 Error POWER AMP output abnormal Error Problem condition Display F61 When POWER is switched on, power become off automatically. During normal operation, if DC DET become L, PCNT shall become L and the error display on the left shall be displayed. (IC501)
11. CD Test Mode Function
This CD test mode is provided to check CD unit without connecting to changer loading mechanism. This mode shall operate CD PLAY with CD unit being connected only and CD Automatic Alignment result is shown on FL display.
11.1. How to set CD test mode
48
2005-05-13
11.2. CD Automatically Adjustment result indication
Under CD test mode, pressing the numeric key `0' on the remote controller will display the auto adjustment result. FLOCK, TLOCK and CLVS status shall be shown as below:
During the above display, executing CD PLAY will display auto adjustment result for CD PLAY mode.
12. Measurements and Adjustments
49
2005-05-13
12.1. Cassette Deck Section
- Measurement Condition - Reverse-mode selector switch: - Tape edit: NORMAL - Record timer: OFF - Make sure head, capstan and press roller are clean. - Judgeable room temperature 20 ± 5 °C (68 ± 9°F) - Measuring instrument - EVM (Electronic Volmeter) - Digital quency counter - Test Tape - Head azimuth adjustment (8 kHz, -20 dB); QZZCFM - Tape speed gain adjustment (3 kHz, -10 dB); QZZCWAT - Playback gain adjustment (315 Hz, 0 dB); QZZCFM
12.1.1. Head Azimuth Adjustment (Deck 1/2)
Caution:
- Please replace both azimuth adjustment screw (RHE5152ZB) and springs
(RM0331) simultaneously when readjusting the head azimuth. (shown in Fig. 2) Even if you wish to readjust the head azimuth without replacing the acrews and springs, a fine adjustment to the azimuth screw and spring.
- Please remove the screw-locking bond left on the head base when replacing
the azimuth screw.
- If you wish to readjust the head azimuth, be sure to adjust with adhering the
cassette tape closely to the mechanism by pushing the center of cassette tape with your finger. (shown in Fig. 3) 1. Playback the azimuth adjustment portion (8 kHz, -20dB) of the test tape (QZZCFM) in the forward play mode. Vary the azimuth adjustment screw until
50
2005-05-13
the output of the R-CH (PB OUT-R) are maximized. 2. Perform the same adjustment in the reverse play mode. 3. After the adjustment, apply screwlock to the azimuth adjusting screw.
12.1.2. Tape Speed Adjustment (Deck 1/2)
1. Set the tape edit button to "NORMAL" position. 2. Insert the test tape (QZZCWAT) to DECK 2 and playback (FWD side) the middle portion of it.
51
2005-05-13
3. Adjust Motor VR (DECK 2) for the output value shown below.
Adjustment target: 2940 ~ 3060 Hz (NORMAL speed)
4. After alignment, assure that the output frequency of the DECK 2 REV and DECK 1 FWD are within ±45 and ±60 Hz respectively of the value of the output frequency of DECK 2 FWD.
12.1.3. Bias and Erase Voltage Check
1. Set the unit "AUX" position. 2. Insert the Normal blank tape (QZZCRA) into DECK 2 and the unit to "REC" mode (use " REC/STOP" key). 3. Measure and make sure that the output is within the standard value.
Bias voltage for Deck 2 Erase voltage for Deck 2 19 ± 4mV (Normal) more than 100mV (Normal)
52
2005-05-13
12.1.4. Bias Frequency Adjustment (Deck 1/2)
1. Set the unit to "AUX" position. 2. Insert the Normal blank tape (QZZCRA) into DECK 2 and set the unit to "REC" mode ( use "REC/STOP" key). 3. Adjust L1002 so that the output frequency is within the standard value.
Standard Value: 98 ±8 kHz
53
2005-05-13
12.2. Tuner Section
12.2.1. AM-IF Alignment
- AM-IF ALIGNMENT
SIGNAL GENERATOR OR SWEEP GENERATOR CONNECTIONS FREQUENCY INDICATOR REMARKS ADJUSTMENT(Shown (ELECTRONIC in Fig.3) VOLTMETER OSCILLOSCOPE) Fashion a loop 450 kHz 30% Point of nonHeadphone Jack Z102 (AM IFT) Adjust for several Mod. at 400Hz. interference (on/ (32 ) Fabricate maximum turns of wire about 600 kHz) the plug as shown output. and radiate in Fig. 2 and then signal into connect the lead loop of wires of the plug receiver. to the measuring instrument. RADIO DIAL SETTING
- AM-RF ALIGNMENT
SIGNAL GENERATOR OR SWEEP GENERATOR CONNECTIONS FREQUENCY Fashion a 522 kHz loop of several turns of wire and radiate signal into loop of receiver. Fashion a 603 kHz loop of several turns of wire and radiate signal into loop of receiver. REMARKS INDICATOR ADJUSTMENT(Shown (ELECTRONIC in Fig.1) VOLTMETER OSCILLOSCOPE) Tuning capacitor Headphone Jack (32 Z101 (AM OSC Coil) Adjust for fully closed. ) Fabricate the maximum plug as shown in output. Fig. 2 and then connect the lead wires of the plug to the measuring instrument. Tuning capacitor Headphone Jack (32 Z101 (AM ANT Coil) Adjust for fully open. ) Fabricate the maximum plug as shown in output. Fig. 2 and then connect the lead wires of the plug to the measuring instrument. RADIO DIAL SETTING
12.3. Alignment Points
54
2005-05-13
Cassette Deck Section
Tuner Section
13. Illustration of IC's, Transistors and Diodes
55 2005-05-13
14. Terminal Function of IC's
14.1. IC701 (AN8885SBE1) Servo Amplifier
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Mark PDE PDF VCC PDA PDB LPD LD RF RFIN CSBRT CEA BDO I/O I I I I I I O O I I I O Function Tracking signal input 1 Tracking signal input 2 Power supply Focus signal input terminal 1 Focus signal input terminal 2 APC amp input APC amp output RFsumming output Detector's input Capacitor for OFTR connection Capacitor for HPF amp connection BDO output ("H" : drop out) APC control Ground NRFDET output ("L" : detection) Power-down input OFTR output N.C. 3T-ENV output N.C. N.C. TE amp input TE amp output FE amp output FE amp input Reference voltage output Tracking balance control Focus balance control
LDON I GND -- /RFDET O PDOWN OFTR NC ENV NC NC TEN TEOUT FEOUT FEN VREF TBAL FBAL O O O O I I I O O I O I I
56
2005-05-13
14.2. IC702 (MN662790RSC) Servo processor/ Digital signal processor/ Digital filter/ D/A converter
Pin No. 1 2 3 4 5 6 Mark BCLK LRCK SRDATA DVDD1 DVSS1 TX I/O O O O I I O Function N.C. N.C. N.C. Power supply input (for digital circuit) GND (for digital circuit) Digital audio interface signal output (Latches data at first transition) Microprocessor command clock signal input Microprocessor command data signal input Microprocessor command load signal input Sense signal output (OFT, FESL,MAGEND , NAJEND,POSAD,SFG) (Not used, open) Focus servo feeding signal output ("L" : Feed) Tracking servo feeding signal output ("L" : Feed) Sub-code block clock signal output (BLKCKf = 75Hz during normal playback) External clock signal input for sub-code Q resistor Sub-code Q code output
7
MCLK
I
8
MDATA
I
9
MLD
I
10
SENSE
O
11
/FLOCK
O
12
/TLOCK
O
13
BLKCK
O
14
SQCK
I
15
SUBQ
O
57
2005-05-13
Pin No. Mark 16 DMUTE 17 STAT
I/O I O
18 19
/RST SMCK
I O
20
CSEL
I
21 22 23 24
TRV TVD PC ECM
O O O O
25
ECS
O
26 27 28 29
KICK TRD FOD VREF
O O O I
30 31 32 33 34
FBAL TBAL FE TE RFENV
O O I I I
Function Muting input ("H" : mute) Status signal output (CRC,CUE,CLVS , TTSTVP,FCLV,SQCK) Reset signal input 1/2-diveded clock signal of crystal osscillating at MSEL = "H" (fSMCK = 8.4672 MHz) 1/4-divided clock signal of crystal oscillating at MSEL = "L" (fSMCK = 4.2336 MHz) Frequency Selection Terminal H = 33.8688 MHz ; L = 16.9344 MHz N.C Traverse drive output Spindle motor ON output ("L" : ON) Spindle motor drive signal output(forced mode output) Spindle motor drive signal output (servo error signal output) N.C. Tracking drive output Focus drive output D/A (drive) output (TVD, ECS, TRD, FOD, FBAL, TBAL) Reference voltage input Focus balance adjustment output Tracking balance adjustment output Focus error signal input (analog input) Tracking error signal input (analog input) RF envelope signal input
58
2005-05-13
Pin No. Mark 35 VDET
I/O I
36 37 38 39 40 41 42
OFT TRCRS /RFDET BDO LDON PLLF2 DSLF2
I I I I O I/O O
43 44 45 46 47 48 49 50 51 52 53
WVEL ARF IREF DRF DSLF PLLF VCOF AVDD2 AVSS2 EFM PCK
O I I I I/O I/O I/O I I -
54
VCOF2
I/O
55
SUBC
O
Function Vibration detection signal input ("H" : detection) Off-track signal input ("H" : off track) Track cross signal input RF detection signal input ("L" : detection) Dropout signal input ("H" : Dropout) Laser on signal output ("H" : ON) N.C. Tracking Offset alignment output/DSL Balance Output (DA Output) N.C. RF signal input Reference current input DSL bias terminal (Not used, open) DSL loop filter terminal PLL loop filter terminal VCO loop filter terminal Power supply input (for analog circuit) GND (for analog circuit) EFM signal output PLL extraction clock output (fPCK = 4.321 MHz during normal playback) VCO Loop filter for 33.8688 MHz conversation terminal for 16.9344 MHz crystal mode, must use other circuit Sub-code serial data output
59
2005-05-13
Pin No. Mark 56 SBCK 57 58 VSS X1 IN
I/O I I I
59
X2 OUT
O
60 61 62
VDD BYTCK /CLDCK
I -
63
FCLK
-
64
IPFLAG
-
65 66
FLAG CLVS
-
67
CRC
-
68
DEMPH
-
69
RESY
-
70 71 72 73 74
IOSEL /TEST AVDD1 OUTL AVSS1
I I I O I
Function Clock input for subcode serial data GND Crystal oscillating circuit input (f = 16.9344MHz) Crystal oscillating circuit input (f = 16.9344 MHz) Power supply input (for oscillating circuit) Byte clock output Sub-code frame clock signal output (fCLDCK = 7.35 kHz during normal playback) Crystal frame clock signal output (fCLK = 7.35 kHz, double = 14.7 kHz) Interpolation flag output ("H" : Interpolation) Flag output Spindle servo phase synchronizing signal output ("H" : CLV, "L" : rough servo) Sub-code CRC checked output ("H' : OK, "L" :NG) De-emphassis ON signal output ("H" : ON) Frame resynchronizing signal output Mode Switching Terminal Test input Power supply input (for analog circuit) Left channel audio signal output GND
60
2005-05-13
Pin No. Mark 75 OUTR 76 RSEL
I/O O I
77 78 79
IOVDD PSEL MSEL
I I I
80
SSEL
I
Function Right channel audio signal output RF signal polarity assignment input (at "H" level, RSEL="H", at "L" level, RESL= "L") 5V supply input Test terminal (connected to Gnd) SMCK oscillating frequency designation input ("L" :4.2336 MHz, "H": 8.4672 MHz) SUBQ output mode select ("H":Q-code buffer mode)
14.3. IC703 (AN8739SBE2) Focus coil/ Tracking coil/ Traverse motor/ Spindle motor driver
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Mark /RST NC IN2 PC2 NC IN1 NC PVCC1 I/O I I I I I Function RESET output terminal N.C. Motor Drive (2) input Turntable motor drive signal ("L :ON) N.C. Motor driver (1) input N.C. Power supply (1) for driver Ground connection (1) for driver N.C. Motor driver (1) reverseaction output Motor driver (1) forwardaction output Motor driver (2) reverseaction output Motor driver (2) forwardaction output
PGND1 NC D1D1+ D2D2+ O O O O
61
2005-05-13
Pin No. Mark 15 D316 17 18 19 20 21 22 23 24 25 26 27 28 D3+ D4D4+
I/O O O O O
NC PGND2 PVCC2 I NC VCC VREF IN4 IN3 RSTIN NC I I I I I -
Function Motor driver (3) reverseaction output Motor driver (3) forwardaction output Motor driver (4) reverseaction output Motor driver (4) forwardaction output N.C. Ground connection (2) for driver Power supply (2) for driver N.C. Power supply terminal Reference voltage input Motor driver (4) input Motor driver (3) input Reset terminal N.C.
14.4. IC600 (M38B79MFA062) System Microprocessor
62
2005-05-13
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Mark DECK2 KEY 4 KEY 3 KEY 2 KEY 1
I/O I
I I I I V_JOG_ADI J_JOG_ADI SER 1 SER 2 SER 3 SPE SER 4 SER 5 SER 6 SER 7 ECONO O O O I O O O O O
Function Deck 2 mechanism condition input Key 4 input Key 3 input Key 2 input Key 1 input Volume jog A-D detection input EQ Joy jog A-D detection input Serial data/clock output Serial data/clock output Serial data/clock output Spectrum analyzer input Serial data/clock output Serial data/clock output Serial data/clock output Serial data/clock output Main transformer control output for economy mode
63
2005-05-13
Pin No. 17 18 19 20 21 22 23 24 25 26 27
Mark CNVSS /RESET XCOUT XCIN VSS XIN XOUT VCC MBP1 MBP2 MCLK / PLLCK MDATA / PLLDA MLD / PLLCE ST/D0 RMT SYNC DCDET N.C. SD DPL/ST MM_RST / EEDA SSEQ_A SSEQ_B SPA SPB SPC SEG1 SEG20 SEG2128 /REG81
I/O O O O
28 29 30 31 32 33 34-36 37 38 39
O O I I I I I I/O
40 41 42 43 44 45-64 65-72
O O O O O
73-76 77-88 89
SEG29-32 O GRD12-1 O VEE -
Function Flash mode terminal (connect to ground) RESET input 32.768 kHz sub clock 32.768 kHz sub clock Ground (0V) 4.19 MHz main clock 4.19 MHz main clock Power supply (+5V) MPU beat proof output 1 MPU beat proof output 2 CD command clock output/tuner PLL clock output CD command data output /tuner PLL data output CD command load output /tuner PLL chip enable Tuner IF data/stereo input Remote control input AC failure detect input DC detect input N.C. Tuner signal detect input Not used Mecha micon reset control output/EEPROM data input Not used Not used Speana control output A Speana control output B Speana control output C Segment drive output (Anode drive output) Segment drive output (Anode drive output) For regional setting/function selection use Segment drive output (Anode drive output) Digit drive output (Grid drive output) Power supply (-30V)
64
2005-05-13
Pin No. 90 91 92 93 94 95
Mark MM_DIN
I/O I
MM_DOUT O MM_CLK I MM_REQ O MM_CS I
REG_IN / I/O EE_CS ECHO_LVLO AVSS VREF TPS DECK 1 I I
96 97 98 99 100
Function Data input from mecha micon Data output to mecha micon Clock input from mecha micon mecha micon request output Chip select input from mecha micon Region and function setting input and eeprom chip select output ECHO level control D/A output Analog ground (0V) Reference for A-D Tape mecha TPS Input/ chrome 1/ chrome 1 tape mecha condition input(Half1/Mode/Photo1 /Photo2)
15. Block Diagram
16. Schematic Diagram
(All schematic diagrams may be modified at any time with the development of the new technology) Note: S501 : Voltage Selector switch S701 : Reset switch S900 : CD Manager switch
65 2005-05-13
S901 : CD 1 switch S902 : CD 2 switch S903 : CD 3 switch S904 : CD 4 switch S905 : CD 5 switch S906 : Rec/Stop select switch S907 : Reverse Mode select switch S908 : Tape Edit select switch S909 : Tune Down switch S910 : FM mode/BP switch S911 : Memory switch S912 : Tune Mode switch S913 : Tune Up switch S914 : Deck 2 Eject switch S920 : CD Eject switch S940 : AUX switch S941 : Tuner switch S942 : Tape switch S943
66 2005-05-13
: CD switch S944 : SSEQ switch S945 : AI EQ switch S950 : S.woofer switch S952 : EQ Up switch S953 : EQ Right switch S954 : EQ Left switch S955 : EQ Down switch S951 : Mode switch S952 : Half switch S953 : Cr02 switch S956 : Power switch S958 : Play/Rec Timer switch S959 : Clock/Timer switch S960 : Karaoke switch S961 : Display /Demo switch S962 : Deck 1 Eject switch S963 : Echo switch S965 : SSS switch
67
2005-05-13
S966 : 6CH switch S967 : DPL switch S971 : Mode switch S972 : Half Switch S973 : Cr02 switch S974 : RECINH_R switch S975 : RECINH_F switch SW1 : Push switch SW2 : Push switch SW3 : Leaf switch SW4 : CD switch SW5 : Lock switch SW 401 : Selector switch SW600 : Joy Jog switch VR900 : VR Volume Jog VR930 : VR Mic
- The voltage value and waveforms are the reference voltage of this unit
measured by DC electronic voltmeter (high impedance) and oscilloscope on the basis of chassis. Accordingly, there may arise some error in voltage values and waveforms depending upon the internal impedance of the tester or the measuring unit.
68
2005-05-13
No mark (( ))
: << >> : Rec Playback : CD () : AM
<> []
: FM : AUX
- Importance safety notice :
mark have special characteristics important for Components identified by safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacturer's specified parts shown in the parts list.
Caution !
IC, LSI and VLSI are sensitive to static electricity. Secondary trouble can be prevented by taking care during repair.
- Cover the parts boxes made of plastics with aluminium foil. - Put a conductive mat on the work table. - Ground the soldering iron. - Do not touch the pins of IC, LSI or VLSI with fingers directly.
"CAUTION: REPLACE FUSIBLE RESISTOR WITH THE SAME TYPE RSFMB40KT-L FUSIBLE RESISTOR""ATTENTION: REMPLACER LA RESISTANCE FUSIBLE PAR UNE RESISTENCE FUSIBLE DE MEME TYPE RSFMB40KT-L.
69
2005-05-13
17. Printed Circuit Board
Note: Circuit board diagrams may be modified at any time with the development of new technology.
70
2005-05-13
18. Wiring Connection Diagram
71
2005-05-13
72
2005-05-13
19. Troubleshooting Guide
73 2005-05-13
74
2005-05-13
75
2005-05-13
20. Parts Location and Replacement Parts List
Notes:
- Important safety notice:
Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used. When replacing any of these components, be sure to use only manufacturer's specified parts shown in the parts list.
- The parenthesized indications in the Remarks columns specify the areas or
colour. (Refer to the cover page for area or colour) Parts without these indications can be used for all areas.
- Warning: This product uses a laser diode. Refer to caution statements on
"Precaution of Laser Diode". ACHTUNG:
- Die Lasereinheit nicht zerlegen. - Die Lasereinheit darf nur gegen eine vom Hertsteller spezifizierte Einheit
ausgetauscht werden.
- Capacitor values are in microfarads (
farads (pF), F= Farads.
F) unless specified otherwise, P= Pico-
- Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM). - The marking (RTL) indicates that the Retention Time is limited for this items.
After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of a availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available.
- [M] Indicates in the Remarks columns indicates parts supplied by MESA.
76 2005-05-13
- The "(SF)" mark denotes the standard part. - Remote Control Unit: Supply period for three years from terminal of production. - Reference for O/I book languages are as follows:
Ar : Cf : Cz : Da : Arabic Du : Canadian French En : Czech Fr : Danish Ge : Dutch English French German It : Ko : Po : Ru : Italian Korean Polish Russian Sp : Sw : Co : Cn : Spanish Swedish Traditional Chinese Simplified Chinese
20.1. Deck Mechanism (RAA3408)
20.1.1. Deck Mechanism Parts Location
20.1.2. Deck Mechanism Parts List
Ref. No. Part No. Part Name & Description CASSETTE DECK 101 101-1 102 102-1 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 RED0050 RHE5152ZB RED0051 RHE5152ZB RDG0300 RDG0301 RDK0026 RDR0029 RDV0033-4 RDV0034-1 RDV0057 RMB0312 RMB0400 RMB0403 RMB0404 RMB0406 RMB0408 RML0370 RML0371 RML0372 R/P HEAD BLOCK UNIT SCREW P/B HEAD BLOCK UNIT SCREW REEL BASE GEAR WINDING RELAY GEAR MAIN GEAR RELAY PULLEY WINDING BELT CAPSTAN BELT `A' MAIN BELT B TRIGGER LEVER SPRING REEL SPRING HEAB PANEL SPRING BRAKE ROD SPRING FR LEVER SP THRUST SPRING TRIGGER LEVER FR LEVER WINDING LEVER [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] Remarks
77
2005-05-13
Ref. No. 119 120 121 122 123 124 125 126 127 128 129 130 130-1 131 131-1 132 133 133-1 133-2 134 135 136 137 138 139
Part No. RML0374 RMM0131 RMM0133-1 RMQ0519 RMS0398-1 RSJ0003 RMC0061 RXF0061 RXF0062 RXG0040 RMK0283A-J RXL0124 RMB0401 RXL0125 RMB0402 RXL0126 RXQ0412 RMB0405 RMM0132 REM0088 RHD26022 XTW2+5L XTW26+10S XYC2+JF17 RFKJXED70-K
Part Name & Description EJECT LEVER BRAKE ROD EJECT ROD REEL HUB MOVING CORE PLUNGER PACK SPRING FLYWHEEL `F' ASS'Y FLYWHEEL `R' ASS'Y FF RELAY GEAR ASS'Y SUB CHASSIS PINCH ROLLER `F' ASS PINCH ARM SPRING `F' PINCH ROLLER `R' ASS PINCH ARM SPRING `R' WINDING ARM ASS'Y HEAD PANEL ASS'Y FR ROD SPRING FR ROD CAP MOTOR ASS'Y MOTOR SCREW HEAD BLOCK UNIT SCREW SUB-CHASSIS SCREW PCB EARTH SCREW CHASSIS ASS'Y
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
20.2. CD Loading Mechanism (RD-DAC026-S)
20.2.1. CD Loading Mechanism Parts Location
20.2.2. CD Loading Mechanism Parts List
78
2005-05-13
Ref. No.
Part No.
Part Name & Description TRAVERSE DECK
Remarks
301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 341 343 344 345 346 347 348 349 350 351 352 353 354
RML0517 RML0516 RMB0551 RMQ0744 RDV0056 RML0525 RML0526 RDG0424 RDG0425 RDG0427 RDG0428 RDG0426 RDG0429 RMB0549-1 RMQ0748 RMB0553 RML0530 RML0518 RMM0201 RME0258 RML0521 RME0257 RML0520 RMM0202 XTB3+10J RMR0334 RMR0624-W2 RMB0561 RMR1121-K RMA1110-2 RMR1122-H1 RMM0204 RMM0203 RDG0432 RML0524 RML0523 RME0260-1 RMR1123-H RXQ0595 RSJ0003 RMA1106 RML0519 RML0522 RMQ0745 RMQ0746 RMB0550 RMQ0747 RME0263 RMQ0743 RMB0552 RDG0430
TIMING LEVER PLUNGER LEVER UPPER SPINDLE SPRING LOWER HOOK BELT FRONT LOCK LEVER DISC LEVER DRIVE GEAR CHANGE GEAR TRAVERSE CAM GEAR TRAVERSE RELAY GEAR UP/DOWN GEAR PULLEY GEAR CHANGE GEAR SPRING PITCH PLATE PUSH SPRING ASSIST LEVER CONNECTION LEVER SLIDE PLATE 1 REAR LOCK SPRING REAR LOCK TRAY LOCK LEVER SPRING TRAY LOCK SLIDE PLATE 2 SCREW FIXED PLATE CLAMPER ASSIST LEVER SPRING MECHA COVER TRAY ANGLE TRAY BASE CARRIER DRIVE RACK SPEED UP GEAR SLIDE LOCK CARRIER LOCK SLIDE LOCK SPRING TRAY MOTOR SUB ASS'Y SOLENOLD ASS'Y UPPER PLATE 8CD LEVER TURNING STOPPER LOWER SPINDLE UP/DOWN BASE LOWER SPINDLE SPRING UPPER HOOK CLICK SPRING SPINDLE SHAFT CUSHION SPRING RELAY GEAR `A'
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
RFKNAAK27GCS MECHA BASE ASS'Y
79
2005-05-13
Ref. No. 355 356 357 358 358-1 358-2 358-3 358-4 358-5 358-6 358-7 358-8 358-9 358-10 359 360 361 362 363 369 370 371 372 373 374
Part No. RDG0431 RME0262 RMA1105 RAE0152Z-3 SHGD113-1 SNSD38 RAF0150A-4S RDG0247 RDG0248 RXQ0339 RXQ0304-1 XQN17+CG5 XQS17+A35FZ XQS17+A35FZ RME0142 RME0109 RMR1124A-K RMS0632 XTN2+6G RMX0141 RMQ0749 RHM0001 RMX0140 RME0261 RMQ0742
Part Name & Description RELAY GEAR `B' DISK LEVER SP. SUPPORT PLATE TRV FLOATING CUSHION TRV MOTOR ASSY SCREW OPU ASSY DRIVE GEAR RELAY GEAR TRV MOTOR ASSY NUT PLATE ASSY NUT PLATE ASSY SCREW TRV MOTOR SCREW SCREW FLOATING SPRING A FLOATING SPRING B TRV CHASSIS TRV PIN SCREW PUSH SPACER UPPER SPINDLE MAGNET DISC SPACER FRONT LOCK SPRING SPINDLE BASE
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
20.3. Cabinet
20.3.1. Cabinet Parts Location
20.3.2. Cabinet Parts List
80
2005-05-13
Ref. No.
Part No.
Part Name & Description CABINET AND CHASSIS
Remarks
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 48-1 49 50 51
REEX0129 REEX0101-1 REEX0131-1 REEX0134 RGB0113-N RGKX0070A-S RGKX0071F-S RGLX0028-Q RGLX0030-Q RGPX0038N-S RGRX0019F-A RGUX0368-S RGUX0369-S RGUX0371-S RGUX0372A-S RGUX0378-S RGUX0379-S RGUX0397-S RGUX0400-S RGUX0377-S RGUX0375-Q1 RGUX0367-Q RGWX0055-S RHD30002-H RKA0059-K RKFX0083-S RKFX0084-S RKFX0085-K1 RKFX0086-K1 RKMX0057-S RKWX0148A-H RKWX0149A-H RKWX0156A-1 RMBX0016-1 RMKX0043 RMKX0044 RMKX0045 RMNX0039-H RMNX0038 RSC0027-2 RSCX0060 RSCX0058 RUS757ZAA RXGX0001 RXXX0021 RYQX0040B-S RYQX0037-S2 RYQX0045C-S RKWX0155-H SHE187-5J XTB3+10J XTB3+10JFZ
14P FFC 28P FFC 18P FFC WIRE 30P FFC WIRE PANA BADGE CD LID CD ORNAMENT POWER LIGHTING CHIP DISC LIGHT CHIP FRONT PANEL REAR PANEL POWER BUTTON CD EJECT BUTTON DISC BUTTON DECK BUTTON DECK EJECT BUTTON L DECK EJECT BUTTON R DISPLAY BUTTON AUXILIARY BUTTON S. WOOFER BUTTON AMAZING BUTTON FUNCTION BUTTON VOLUME KNOB SCREW LEG RUBBER CASS. LID (L) CASS. LID (R) CASS HOLDER (L) CASS HOLDER (R) TOP CABINET (BENT) CASS. WINDOW (L) CASS. WINDOW (R) FL FILTER CASS. OPEN SPRING BOTTOM CHASSIS INNER CHASSIS T-BRACKET SUB TRANS HOLDER FL HOLDER TUNER PACK SHIELD PLATE HEAD DECK SHIELD PLATE CASSETTE HALF SPRING DAMPER GEAR HEAT SINK UNIT CONTROL BTN UNIT JOY JOG UNIT FL ORNAMENT UNIT REMOTE SENSOR WINDOW PCB SUPPORT SCREW SCREW
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
81
2005-05-13
Ref. No. 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67
Part No. XTB3+20J XTBS26+10J XTBS3+8JFZ1 XTW3+15T XTW3+8T RGUX0376-S RGUX0381-Q RGUX0380A-S REM0072-3 RMNX0047 RSCX0051 RGW0341-S SHR301 REEX0135 RMQX0049 RJFX0001
Part Name & Description SCREW SCREW SCREW SCREW SCREW 3D AI BUTTON PPL/SSS 6 CH BUTTON KARAOKE / RDS BUTTON FAN MIC PCB HOLDER SHIELD PLATE MIC MIC KNOB LEAD CLAMPER 30P FFC WIRE DPL LIGHT LEAKAGE CO PCB SPACER
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
20.4. Component Parts List
82
2005-05-13
Ref. No.
Part No.
Part Name & Description PRINTED CIRCUIT BOARD
Remarks
REPX0145C RD-DVK029-SY REPX0257A REPX0259B REPX0258B REPX0258B REPX0258B REPX0258B REPX0258B REPX0198C REPX0108 REPX0108A REP1999B REPX0245E REPX0251A REPX0251A REPX0251A REP2578A-N REP2578A-N REP2578A-N
CD SERVO P.C.B. VIDEO P.C.B. VCD P.C.B. MAIN/TUNER P.C.B. PANEL P.C.B. MIC P.C.B. HEADPHONE P.C.B. TACT SWITCH (1) P.C.B. TACT SWITCH (2) P.C.B. DECK P.C.B. MECHANISM (DECK 1) P.C.B. MECHANISM (DECK 2) P.C.B. TUNER PACK P.C.B. POWER P.C.B. AC TRANSFORMER P.C.B. SUB-TRANSFORMER P.C.B. VOLTAGE SELECTOR P.C.B. CD LOADING P.C.B. CD DETACT P.C.B. SPINDLE POSITION P.C.B. INTEGRATED CIRCUITS
[M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL) [M](RTL)
IC1 IC101 IC102 IC262 IC263 IC300 IC301
TA7291P
IC DRIVE
[M] [M] [M] [M] [M] [M] [M]
LA1833NMNTLM IC IF & MPX LC72131MDTRM IC PLL BA4558FE2 TC4052BFNELM BU9255FS-E2 TC4052BFNELM IC BUFFER AMP IC ANALOG SWITCH IC SOUND MIXER IC ANALOG SWITCH
83
2005-05-13
Ref. No. IC302 IC303 IC304 IC307 IC308 IC309 IC310 IC400 IC401 IC500 IC501 IC600 IC601 IC602 IC603 IC701 IC702 IC703 IC802 IC803 IC951 IC971 IC1000 IC1001 IC1001 IC1002 IC1002 IC1003 IC1003 IC1004 IC1004
Part No. BH3874AKS2 M62464FP BA4558FE2 BU4066BCF-E2 M5218AP M5228FPE1 M62429FP BA033T SI8050JLF118 RSN311W64B-P STK470-080 M38B79MFA062 BU2090AF-E2 BU2090AF-E2 BR93LC46F-GG AN8885SBE1 MN662790RSC AN8739SBE2 M38039MC052 TC7W14FTE12L 0N2180RLC1 0N2180RLC1 MN89103M2 AN7348STA-E1 LH532KU1 BU2090AF-E2 M44260CTP7 BA4558FE2 TC7WU04FUT2L BA7755A TC7W14FUTE1L
Part Name & Description IC ASP IC DOLBY PROLOGIC DECODER IC BUFFER AMP IC QUAD ANALOG SW IC BUFFER AMP IC QUAD OP AMP IC 2CH ELECTRONIC VOL IC 3.3V REC IC VOLTAGE REGULATOR IC HIC IC REGULATOR IC MICROPROCESSOR IC I/O EXPANDER IC I/O EXPANDER IC EEPROM IC RFAMP IC LSI IC 4CH DRIVER IC MICROPROCESSOR IC INVERTER IC PHOTO INTERRUPTER IC PHOTO INTERRUPTER IC TAPE PB IC 2M ROM IC I/O EXPANDER IC 4M DRAM IC BUFFER AMP IC INVERTER IC R/P SELECT IC INVERTER TRANSISTORS
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
IC MPEG VIDEO AUDIO DECODER [M]
Q1 Q1 Q2 Q3 Q4 Q101 Q106 Q108 Q201 Q202 Q203 Q204 Q205 Q210 Q211 Q250 Q251 Q252
2SK544F-AC RVTDTC143EST 2SC2786MTA 2SC2787FL1TA 2SC2787FL1TA 2SC2058SPTA KRA102MTA KRC101STA KTD1304TA KTD1304TA KTD1304TA KTD1304TA KTD1304TA KTD1304TA KTD1304TA 2SC2412KT96R KTA12710YTA 2SC2412KT96R
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
84
2005-05-13
Ref. No. Q253 Q262 Q300 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q401 Q402 Q403 Q405 Q409 Q410 Q411 Q412 Q420 Q422 Q424 Q450 Q503 Q505 Q510 Q514 Q520 Q521 Q570 Q571 Q572 Q573 Q600 Q601 Q602 Q603 Q604 Q605 Q607 Q608 Q609 Q701 Q801 Q802 Q803 Q804 Q805 Q806 Q807
Part No. 2SC2412KT96R KTD1304TA KTA1504GRTA KRA102STA 2SB621ARSTA KRC102STA 2SB621ARSTA KRC102STA KRA111STA KRC111STA KRA111STA KTC3875GRTA KTD1304TA KTD1304TA KTD1304TA KTD1304TA KRA102STA 2SD2114K1V KRA102STA KRA102STA 2SB621ARSTA KRC102STA KRA111STA KTC3875GRTA KTC3199GRTA KTC3199GRTA 2SD2144STA KTC3199GRTA KTC3199GRTA KRA102MTA 2SD2137PQTA KRC102MTA KTC3199GRTA 2SD2144STA KTA12710YTA KRC103MTA KRC102MTA 2SA933SSTA KTC3199GRTA KRC102MTA KTC3199GRTA KTC3199GRTA KTC3199GRTA 2SA1037AKSTX KRC102STA 2SC2712GRT5T 2SC2712GRT5T 2SC2712GRT5T KRC101STA KRC101STA KRC101STA
Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
85
2005-05-13
Ref. No. Q808 Q930 Q931 Q932 Q1001 Q1003 Q1004 Q1005 Q1006 Q1007 Q1008 Q1009 Q1010 Q1011 Q1012 Q1013 Q1014 Q1015 Q1016 Q1017 Q1018 Q1019 Q1020 Q1021 Q1022 Q1023 Q1024
Part No. KRC101STA 2SC1740SSTA KTC3199GRTA 2SC1740SSTA KTC3199GRTA 2SD2144STA 2SD2144STA 2SD2144STA KRC114STA KTC3875GRTA KTC3875GRTA KTC3875GRTA KTC3875GRTA KTC3875GRTA KTD1304TA KTD1304TA 2SC2412KT96R 2SC2412KT96R KRA102STA KTD1146YTA KTA12710YTA KTA12710YTA KTD1304TA KTD1304TA KRA102STA KRA102STA 2SD2144STA
Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DIODES
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
D1 D1 D2 D2 D3 D101 D250 D300 D301 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D313 D403 D405 D502 D503
GP1S94 SVC211SPA-AL MTZJ4R7BTA SVC211SPA-AL SVC211SPA-AL UDZSTE175R1B DAP202KT146 MA728TX MA728TX UDZSTE175R1B RL1N4003S-P RL1N4003S-P MA8300MTX 1SS355TE17 DAP202KT146 DAP202KT146 DAP202KT146 RL1N4003S-P RL1N4003S-P UDZSTE177R5B RL1N4003N02 EK14LFH2K RL1N4003S-P RL1N4003S-P
DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
86
2005-05-13
Ref. No. D504 D505 D510 D512 D513 D514 D515 D516 D517 D518 D519 D520 D521 D522 D570 D572 D573 D574 D576 D577 D578 D580 D581 D601 D602 D603 D604 D605 D606 D607 D610 D611 D612 D613 D620 D621 D693 D695 D696 D697 D800 D801 D903 D904 D914 D915 D916 D917 D918 D946 D947
Part No. RVD1SS133TA RVD1SS133TA RVD1SS133TA 1N5402BM21 1N5402BM21 1N5402BM21 RVD1SS133TA 1N5402BM21 RK306LFU1 1N5402BM21 RK306LFU1 1N5402BM21 1N5402BM21 1N5402BM21 1T3T 1T3T 1T3T RVD1SS133TA KBP152G4R5 1T3T 1SS291TA MTZJ7R5ATA 1T3T RVD1SS133TA RVD1SS133TA
Part Name & Description DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
SLR325MCT31W DIODE SLR325MCT31W DIODE SLI325URCT31 RVD1SS133TA RVD1SS133TA MA723TA RVD1SS133TA MA700ATA MA4020LTA 1SS291TA 1SS291TA RVD1SS133TA RVD1SS133TA RVD1SS133TA RVD1SS133TA 1SS355TE17 1SS355TE17 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE SLR325MCT31W DIODE
87
2005-05-13
Ref. No. D948 D949 D951 D951 D953 D954 D971 D1002 D1003 D1004
Part No. SLR325DCT31 MA165TA SLR325DCT31 SLR325DCT31 MA165TA 1SS355TE17 1SS355TE17 UDZTE173R6B
Part Name & Description DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE VARIABLE RESISTORS
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
SLR325MCT31W DIODE
SLR325MCT31W DIODE
VR900 VR930
EVEKE2F2524B RRV06A02C24A
VR VOLUME JOG VR MIC SWITCHES
[M] [M]
S501 S701 S900 S901 S902 S903 S904 S905 S906 S907 S908 S909 S910 S911 S912 S913 S914 S920 S940 S941 S942 S943 S944 S945 S950 S951 S952 S952 S953 S953 S954 S955 S956 S958 S959 S960
RSR4B008S-Q RSH1A043-U EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R RSH1A018-3U EVQ11G07K RSH1A019-2U EVQ11G07K RSH1A019-2U EVQ11G07K EVQ11G07K EVQ21405R EVQ21405R EVQ21405R EVQ21405R
SW VOLTAGE SELECTOR SW RESET SW CD MANAGER SW CD 1 SW CD 2 SW CD 3 SW CD 4 SW CD 5 SW REC STOP SW REV MODE SW TAPE EDIT SW TUNE DOWN SW FM MODE/BP SW MEMORY SW TUNE MODE SW TUNE UP SW DECK 2 EJECT SW CD EJECT SW AUX SW TUNER SW TAPE SW CD SW SS EQ SW AI EQ SW S. WOOFER SW MODE SW EQ UP SW HALF SW EQ RIGHT SW CR02 SW EQ LEFT SW EQ DOWN SW POWER PLAY/REC SW CLOCK/TIMER SW KARAOKE
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
88
2005-05-13
S960
EVQ21405R
SW KARAOKE
[M]
89
2005-05-13
Ref. No. S961 S962 S963 S965 S966 S967 S971 S972 S973 S974 S975
Part No. EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R RSH1A018-3U RSH1A019-2U RSH1A019-2U RSH1A019-2U RSH1A019-2U
Part Name & Description SW DISPLAY/DEMO SW DECK 1 EJECT SW ECHO SW SSS SW 6CH I/P SW DPL SW MODE SW HALF SW CR02 SW RECINH_R SW RECINH_F SWITCHES
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
SW1 SW2 SW3 SW4 SW5 SW401 SW600
RSH1A032-U RSH1A032-U RSH1A005-1U RSH1A91ZA-A RSP1A017-A RSS2A56ZA-H ESE24SV2
SW PUSH SW PUSH SW SW CD SW LOCK SW SELECTOR SW JOY JOG CONNECTORS
[M] [M] [M] [M] [M] [M] [M]
CN1 CN204 CN205 CN250 CN305 CN500 CN501 CN502 CN701 CN702 CN801 CN802 CN803 CN900 CN1000 CN1001 CP400 CP401 CP402 CP403 CP500 CP501 CP605 CP607 CP900 CP1001 CP1002 CS951
RJS1A9414 RJS1A5210 RJS1A9414-1 RJP2G4YA RJS1A9430 RJT029W03VT RJT119W13H RJP6G18ZA RJS2A8616 RJS2A4230-1F RJU107K30M RJS2A3330 RJS1A9430 RJT066H12F RJT107K30T RJS8T7ZA RJU057G12 RJU057G12 RJS1A9428-1 RJS1A9418 RJT057G12 RJT057G12 RJS1A9418 RJS1A9428-1 RJU066H12M RJT071K09A RJT071K09A RJU071H09M1
FF CONNECTOR 10P WIRE HOLDER 14P CONNECTOR CONNECTOR 30P CONNECTOR CONNECTOR 13P CONNECTOR SOCKET 16P FPC CONNECTOR 30P CONNECTOR 30P CONNECTOR 30P CONNECTOR 30P CONNECTOR 12P BTB CONNECTOR (M 30P CONNECTOR 8P MOLEX 12P P2 MQ CONNECTOR 12P P2 MQ CONNECTOR 28P FFC CONNECTOR CONNECTOR 12P P2 MQ CONNECTOR 12P P2 MQ CONNECTOR CONNECTOR 28P FFC CONNECTOR 12P BTB CONNECTOR 9P B/B CONNECTOR 9P B/B CONNECTOR CONNECTOR
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
90
2005-05-13
Ref. No. CS971 CS1001 CS1002
Part No. RJU071H09M1 RJS1A6805-J RJS1A6805-J
Part Name & Description CONNECTOR 5P CONNECTOR SOCKET 5P CONNECTOR SOCKET COILS & TRANSFORMERS
Remarks [M] [M] [M]
L1 L2 L102 L401 L402 L403 L406 L603 L605 L701 L702 L703 L704 L801 L802 L803 L920 L921 L922 L930 L931 L1000 L1001 L1002 L1002 T501 T502
RLQZP1R2KT-Y RLQZPR47KT-Y RLQB1R0KTD-D RLL500050T-Y RLQX101M-T RLL500050T-Y RLL500050T-Y RLQB3R3JTD-D RLQB101JTD-D RLBN102V-Y RLBN102V-Y RLBN102V-Y RLBN102V-Y RLL500050T-Y RLL500050T-Y RLL500050T-Y RLQB101JTD-D RLQB101JTD-D RLQB100JTD-D RLQB100JTD-D RLQB100JTD-D RLQP1R8KT2-Y RLQB470JTD-D 7L1A62N RLQP2R7KT2-Y RTP1P3E009-V RTP1H3E001
COIL COIL INDUCTOR RF CHOKE COIL COIL RF CHOKE COIL RF CHOKE COIL COIL INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR RF CHOKE COIL RF CHOKE COIL RF CHOKE COIL INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR COIL RF CHOKE COIL BIAS OSC COIL COIL MAIN POWER TRANSFORM BACKUP TRANSFORMER
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
[M] [M]
COMPONENT COMBINATION Z101 Z102 Z501 Z940 Z971 Z1001 Z1002 RLA2Z006M-T RLI2Z021M-T ERZV10V511CS RCD37142TC5 EXBF7L355SYV RGSD12A1445T RGSD12A1445T ANT COIL BLOCK AM IF BLOCK ZENER REMOTE CONTROL SENSO RADA RESISTOR SENSOR SENSOR CERAMIC FILTERS CF201 CF202 RLFFETWND01M FM CF RLFFETWND01M FM CF RELAY RL502 RSY0056M-C PRIMAY RELAY [M] [M] [M] [M] [M] [M] [M] [M] [M]
[M]
91
2005-05-13
[M]
92
2005-05-13
Ref. No. RL504
Part No. RSY0060M-R
Part Name & Description RELAY OSCILLATORS
Remarks [M]
X102 X103 X600 X601 X701 X800 X1000
RLFDFT22DD RSXC7M20S05T RSXZ4M19B01T RSXD32K7S02 RSXB16M9J02T RSXY6M00D01T RSXC27M0S02T
DISCRIMINATOR CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR CERAMIC RESONATOR OSCILLATOR DISPLAY TUBE
[M] [M] [M] [M] [M] [M] [M]
FL600
RSL0316-F
FL DISPLAY FUSES
[M]
F1 F2
XBA2C31TB0 XBA2C16TB0
FUSE 1.6A PRIMAY FUSE
[M] [M]
FUSE HOLDERS FC1 FC2 FC3 FC4 EYF52BC EYF52BC EYF52BC EYF52BC FUSE HOLDER FUSE HOLDER FUSE HOLDER FUSE HOLDER HOLDERS H501 H600 H601 H920A H920B H930A H930B H940A H940B H1001 RJS1A5513 RMR0317 RMR0315 RMR0315 RMR0315 RMR0314 RMR0314 RMR0318 RMR0318 RMR0319 13P WIRE HOLDER 8P CABLE HOLDER 6P CABLE HOLDER 6P CABLE HOLDER 6P CABLE HOLDER 5P CABLE HOLDER 5P CABLE HOLDER 9P CABLE HOLDER 9P CABLE HOLDER 10P CABLE HOLDER JACKS JK101 JK201 JK202 JK203 JK400 JK500 JK502 JK503 JK504 JK920 RJH5414-1 RJH2405N RJH2603N-4 RJH2110N-2 SJFD7-6 SJS9236-J RJR0054K-J RJR0054K-J RJH5603-4 RJJ37TK07-X JK ANTENNA JK 4P RCA JK 6P RCA PIN JK SUB-WOOFER JK VIDEO JK AC INLET JK SPEAKER JK SPEAKER JK SPEAKER TERMINAL JK HP/MIC [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
93
2005-05-13
Ref. No. JK930 JK931
Part No. RJJ37TK09 RJJ37TK09
Part Name & Description JK PHONE JK PHONE EARTH TERMINAL
Remarks [M] [M]
E500
SNE1004-2
EARTH TERMINAL WIRES
[M]
W1 W1 W2 W2 W3 W5 W6 W7 W8 W500 W501 W600 W601 W920 W930 W940 W1001 W1002
REE0854 REZ1023-1 REEX0061 REZ1024 REEX0059 REEX0086 REEX0057 REEX0062 REE0782 REXX0206 REXX0235 RWJ0208155RX REXX0253 RWJ0206250XX RWJ0205250XX RWJ1109140RR RWJ8010160RX RWJ0102050CK
PRI WIRE YELLOW 4P WIRE WIRE (BLACK) 3P WIRE WIRE (BLUE) WIRE (RED) WIRE (ORANGE) WIRE (WHITE) WIRE (GREY) 2P STANDBY WIRE 13P FLAT WIRE WIRE 8P PANEL TO DEC 6P WIRE 6P (2) FLAT WIRE 5P FLAT WIRE 9P WIRE 10P WIRE WIRE JUMPER PLATE
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
PL1
RJR0199
JUMPER PLATE RESISTORS
[M]
R1 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R102 R103 R104 R105 R106 R107 R110 R111
ERDS2TJ102T ERDS2TJ104T ERDS2TJ104T ERDS2TJ221T ERDS2TJ104T ERDS2TJ564T ERDS2TJ391T ERDS2TJ272T ERDS2TJ684T ERDS2TJ391T ERDS2TJ391T ERDS2TJ684T ERJ3GEYJ472V ERJ3GEYJ271V ERJ3GEYJ102V ERJ3GEYJ471V ERJ3GEYJ474V ERJ3GEYJ331V ERJ3GEYJ102V ERJ3GEYJ391V
1K 1/4W 100K 1/4W 100K 1/4W 220 1/4W 100K 1/4W 560K 1/4W 390 1/4W 2.7K 1/4W 680K 1/4W 390 1/4W 390 1/4W 680K 1/4W 4.7K 1/16W 270 1/16W 1K 1/16W 470 1/16W 470K 1/16W 330 1/16W 1K 1/16W 390 1/16W
[M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
94
2005-05-13
Ref. No. R112 R113 R114 R115 R116 R117 R118 R119 R120 R121 R122 R123 R124 R125 R126 R127 R128 R129 R130 R131 R132 R133 R134 R135 R136 R137 R138 R141 R142 R143 R145 R146 R151 R152 R155 R156 R157 R158 R159 R160 R161 R169 R170 R171 R174 R175 R176 R177 R178 R179 R180 R181 R182 R183
Part No. ERJ3GEYJ104V ERJ3GEYJ103V ERJ3GEYJ562V ERJ3GEYJ561V ERJ3GEYJ102V ERJ3GEYJ473V ERJ3GEYJ332V ERJ3GEYJ332V ERJ3GEYJ473V ERJ3GEYJ223V ERJ3GEYJ272V ERJ3GEYJ683V ERJ3GEYJ330V ERJ3GEYJ471V ERJ3GEYJ102V ERJ3GEYJ471V ERJ3GEYJ820V ERJ3GEYJ273V ERJ3GEYJ103V ERJ3GEYJ680V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ471V ERJ3GEYJ102V ERJ3GEYJ102V ERJ3GEYJ102V ERJ3GEYJ332V ERJ3GEYJ682V ERJ3GEYJ682V ERJ3GEYJ223V ERJ3GEYJ104V ERJ3GEYJ104V ERJ3GEYJ820V ERJ3GEY0R00V ERJ3GEYJ683V ERJ3GEYJ104V ERJ3GEYJ1R0V ERJ3GEYJ1R0V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ103V ERJ3GEYJ222V ERJ3GEYJ101V ERJ3GEYJ102V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ223V ERJ3GEYJ103V ERJ3GEYJ822V ERJ3GEYJ222V ERJ3GEYJ123V ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ122V
Part Name & Description 100K 1/16W 10K 1/16W 5.6K 1/16W 560 1/16W 1K 1/16W 47K 1/16W 3.3K 1/16W 3.3K 1/16W 47K 1/16W 22K 1/16W 2.7K 1/16W 68K 1/16W 33 1/16W 470 1/16W 1K 1/16W 470 1/16W 82 1/16W 27K 1/16W 10K 1/16W 68 1/16W 10K 1/16W 1K 1/16W 470 1/16W 1K 1/16W 1K 1/16W 1K 1/16W 3.3K 1/16W 6.8K 1/16W 6.8K 1/16W 22K 1/16W 100K 1/16W 100K 1/16W 82 1/16W 0 1/16W 68K 1/16W 100K 1/16W 1 1/16W 1 1/16W 10K 1/16W 1K 1/16W 10K 1/16W 2.2K 1/16W 100 1/16W 1K 1/16W 10K 1/16W 10K 1/16W 22K 1/16W 10K 1/16W 8.2K 1/16W 2.2K 1/16W 12K 1/16W 4.7K 1/16W 10K 1/16W 1.2K 1/16W
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
95
2005-05-13
Ref. No. R184 R186 R187 R188 R189 R190 R191 R192 R193 R194 R195 R196 R197 R198 R199 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R213 R214 R215 R216 R217 R218 R221 R222 R223 R224 R225 R226 R227 R228 R229 R230 R231 R232 R233 R234 R235 R236 R237 R238 R239 R240 R241 R242 R243
Part No. ERJ3GEYJ104V ERJ3GEYJ223V ERJ3GEYJ223V ERJ3GEYJ1R0V ERJ3GEYJ471V ERJ3GEYJ104V ERJ3GEYJ472V ERJ3GEYJ102V ERJ3GEYJ103V ERJ3GEYJ123V ERJ3GEYJ473V ERJ3GEYJ153V ERJ3GEYJ153V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEYJ392V ERJ3GEYJ102V ERJ3GEYJ473V ERJ3GEYJ152V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ563V ERJ3GEYJ224V ERJ3GEYJ222V ERJ3GEYJ103V ERJ3GEYJ222V ERJ3GEYJ103V ERJ3GEYJ104V ERJ3GEYJ272V ERJ3GEYJ472V ERJ3GEY0R00V ERJ3GEYJ104V ERJ3GEYJ102V ERJ3GEYJ472V ERJ3GEYJ473V ERJ3GEYJ472V ERJ3GEYJ273V ERJ3GEYJ332V ERJ3GEYJ681V ERJ3GEYJ273V ERJ3GEYJ472V ERJ3GEYJ104V ERJ3GEYJ390V ERJ3GEYJ390V ERJ3GEYJ222V ERJ3GEYJ103V ERJ3GEYJ101V ERJ3GEYJ272V ERJ3GEYJ333V ERJ3GEYJ152V ERJ3GEYJ104V ERJ3GEYJ102V ERJ3GEYJ104V
Part Name & Description 100K 1/16W 22K 1/16W 22K 1/16W 1 1/16W 470 1/16W 100K 1/16W 4.7K 1/16W 1K 1/16W 10K 1/16W 12K 1/16W 47K 1/16W 15K 1/16W 15K 1/16W 0 1/16W 0 1/16W 10K 1/16W 3.9K 1/16W 1K 1/16W 47K 1/16W 1.5K 1/16W 10K 1/16W 1K 1/16W 56K 1/16W 220K 1/16W 2.2K 1/16W 10K 1/16W 2.2K 1/16W 10K 1/16W 100K 1/16W 2.7K 1/16W 4.7K 1/16W 0 1/16W 100K 1/16W 1K 1/16W 4.7K 1/16W 47K 1/16W 4.7K 1/16W 27K 1/16W 3.3K 1/16W 680 1/16W 27K 1/16W 4.7K 1/16W 100K 1/16W 39 1/16W 39 1/16W 2.2K 1/16W 10K 1/16W 100 1/16W 2.7K 1/16W 33K 1/16W 1.5K 1/16W 100K 1/16W 1K 1/16W 100K 1/16W
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
96
2005-05-13
Ref. No. R244 R245 R246 R247 R248 R249 R250 R251 R252 R253 R254 R255 R256 R257 R258 R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R269 R270 R271 R272 R273 R275 R276 R279 R281 R282 R283 R284 R300 R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R314 R315 R316
Part No. ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ103V RSFMB10KT-L ERJ3GEYJ683V ERJ3GEYJ472V ERJ3GEYJ824V ERJ3GEYJ103V ERJ3GEYJ824V ERJ3GEYJ562V ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ563V ERJ3GEYJ103V ERJ3GEYJ101V ERJ3GEYJ563V ERDS1FVJ180T ERJ3GEYJ563V ERJ3GEYJ104V ERJ3GEYJ821V ERJ3GEYJ101V ERJ3GEYJ473V ERJ3GEYJ182V ERJ3GEYJ223V ERJ3GEYJ563V ERJ3GEYJ471V ERJ3GEYJ102V ERJ3GEYJ152V ERJ3GEYJ824V ERJ3GEYJ824V ERJ3GEY0R00V ERJ3GEYJ821V ERJ3GEYJ681V ERJ3GEY0R00V ERJ3GEYJ223V ERJ3GEY0R00V ERJ3GEYJ102V ERJ3GEYJ103V ERJ3GEYJ104V ERJ3GEYJ104V ERJ3GEYJ103V ERJ3GEYJ473V ERJ3GEYJ473V ERJ3GEYJ822V ERJ3GEYJ473V ERJ3GEYJ473V ERJ3GEYJ822V ERJ3GEYJ183V ERJ3GEYJ123V ERJ3GEYJ392V ERJ3GEYJ683V ERJ3GEYJ472V ERJ3GEYJ273V ERJ3GEYJ222V
Part Name & Description 220 1/16W 10K 1/16W 10K 1/16W PROTECTOR 68K 1/16W 4.7K 1/16W 820K 1/16W 10K 1/16W 820K 1/16W 5.6K 1/16W 4.7K 1/16W 10K 1/16W 56K 1/16W 10K 1/16W 100 1/16W 56K 1/16W 18 1/2W 56K 1/16W 100K 1/16W 820 1/16W 100 1/16W 47K 1/16W 1.8K 1/16W 22K 1/16W 56K 1/16W 470 1/16W 1K 1/16W 1.5K 1/16W 820K 1/16W 820K 1/16W 0 1/16W 820 1/16W 680 1/16W 0 1/16W 22K 1/16W 0 1/16W 1K 1/16W 10K 1/16W 100K 1/16W 100K 1/16W 10K 1/16W 47K 1/16W 47K 1/16W 8.2K 1/16W 47K 1/16W 47K 1/16W 8.2K 1/16W 18K 1/16W 12K 1/16W 3.9K 1/16W 68K 1/16W 4.7K 1/16W 27K 1/16W 2.2K 1/16W
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
97
2005-05-13
R316
ERJ3GEYJ222V
2.2K 1/16W
[M]
98
2005-05-13
Ref. No. R317 R318 R319 R320 R321 R322 R323 R324 R325 R326 R327 R328 R329 R330 R331 R332 R333 R334 R335 R336 R337 R338 R339 R340 R341 R342 R343 R344 R345 R346 R347 R348 R349 R350 R351 R352 R353 R354 R355 R356 R357 R358 R359 R360 R393 R394 R395 R396 R397 R398 R399 R400 R401 R402
Part No. ERJ3GEYJ272V ERJ3GEYJ472V ERJ3GEYJ104V ERJ3GEYJ104V ERJ3GEYJ753V ERJ3GEYJ473V ERJ3GEYJ154V ERJ3GEYJ753V ERJ3GEYJ473V ERJ3GEYJ154V ERJ3GEYJ334V ERJ3GEYJ100V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEYJ101V ERJ3GEYJ101V ERJ3GEYJ272V ERJ3GEYJ271V ERJ3GEYJ104V ERJ3GEYJ683V ERJ3GEYJ102V ERD2FCVJ4R7T ERJ3GEYJ472V ERJ3GEYJ151V ERJ3GEY0R00V ERJ3GEYJ473V ERJ3GEYJ472V ERJ3GEYJ472V ERJ3GEYJ471V ERJ3GEYJ393V ERJ3GEYJ153V ERJ3GEYJ472V ERJ3GEYJ102V ERJ3GEYJ102V ERJ3GEYJ104V ERJ3GEYJ104V ERJ3GEYJ222V ERJ3GEYJ183V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ154V ERJ3GEYJ102V ERJ3GEYJ102V ERJ3GEY0R00V ERJ3GEY0R00V
Part Name & Description 2.7K 1/16W 4.7K 1/16W 100K 1/16W 100K 1/16W 75K 1/16W 47K 1/16W 150K 1/16W 75K 1/16W 47K 1/16W 150K 1/16W 330K 1/16W 10 1/16W 0 1/16W 10K 1/16W 0 1/16W 10K 1/16W 0 1/16W 10K 1/16W 0 1/16W 10K 1/16W 100 1/16W 100 1/16W 2.7K 1/16W 270 1/16W 100K 1/16W 68K 1/16W 1K 1/16W 4.7 1/4W 4.7K 1/16W 150 1/16W 0 1/16W 47K 1/16W 4.7K 1/16W 4.7K 1/16W 470 1/16W 39K 1/16W 15K 1/16W 4.7K 1/16W 1K 1/16W 1K 1/16W 100K 1/16W 100K 1/16W 2.2K 1/16W 18K 1/16W 10K 1/16W 1K 1/16W 4.7K 1/16W 10K 1/16W 1K 1/16W 150K 1/16W 1K 1/16W 1K 1/16W 0 1/16W 0 1/16W
Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]
99
2005-05-13
Ref. No. R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R421 R422 R423 R424 R425 R426 R427 R428 R429 R430 R431 R432 R433 R434 R435 R436 R437 R438 R439 R440 R441 R442 R443 R444 R446 R447 R448 R449 R450 R451 R454 R455 R456 R457 R458 R459 R460
Part No. ERJ3GEYJ103V ERJ3GEYJ392V ERJ3GEYJ102V ERJ3GEYJ473V ERJ3GEYJ152V ERJ3GEYJ103V ERJ3GEYJ102V E