Text preview for : 987713201.pdf part of Sony D-EJ361 CD Man
Back to : D-EJ361.rar | Home
D-EJ361/EJ361SR/EJ365
SERVICE MANUAL
Ver 1.0 2003.03
Canadian Model
D-EJ361
AEP Model
D-EJ361/EJ361SR
E Model
D-EJ361/EJ365
Australian Model
D-EJ361
Chinese Model
D-EJ365
Photo : D-EJ365 (SILVER)
Model Name Using Similar Mechanism CD Mechanism Type Optical Pick-up Type
New CDM-3325ER DAX-25E
SPECIFICATIONS
System Compact disc digital audio system Laser diode properties Material: GaAlAs Wavelength: = 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Power requirements For the area code of the model you purchased, check the upper left side of the bar code on the package. · Two LR6 (size AA) batteries: 3 V DC · AC power adaptor (DC IN 4.5 V jack): Canadian, Central and South America, Mexican, Taiwan models : 120 V, 60 Hz Australian model : 240 V, 50 Hz AEP, EE, E18 models : 100 - 240 V, 50/60 Hz Hong Kong model : 230 V, 50/60 Hz Chinese model : 220 V, 50 Hz Dimensions (w/h/d) (without projecting parts and controls) Approx. 136 x 26 x 150 mm (5 3 /8 x 1 1 /16 x 6 in.) Mass (excluding accessories) Approx. 185 g (6.6 oz) Operating temperature 5°C - 35°C (41°F - 95°F) Design and specifications are subject to change without notice.
Supplied Accessories
D-EJ361: AC power adaptor (1) Headphones/earphones (1) D-EJ361SR*: AC power adaptor (1) Headphones/earphones (1) Active speaker system (1) * "Operating Instructions for the active speaker system" is enclosed. D-EJ365: Headphones (1) AC power adaptor (1) Remote commander (1) Rechargeable battery (1)
PORTABLE CD PLAYER
9-877-132-01
2003C0200-1 © 2003.03
Sony Corporation
Personal Audio Company Pubulished by Sony Engineering Corporation
D-EJ361/EJ361SR/EJ365
TABLE OF CONTENTS
DANGER Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Specifications ............................................................................ 1
1. SERVICING NOTES ................................................... 3 2. GENERAL
Locating the Controls ......................................................... 3
3. DISASSEMBLY
3-1. Upper Lid ASSY, Cabinet (Upper) Sub ASSY ........... 4 3-2. MD ASSY, Main Board .............................................. 5 3-3. "Motor ASSY (Sled) (M902)", Optical Pick-up (DAX-25E), "Motor ASSY, Turn Table (Spindle) (M901)" ............ 5
4. ELECTRICAL ADJUSTMENS ............................... 6 5. DIAGRAMS
5-1. Block Diagram ............................................................ 7 5-2. Printed Wiring Boards ................................................ 8 5-3. Schematic Diagram MAIN SECTION (1/3) ......... 9 5-4. Schematic Diagram MAIN SECTION (2/3) ....... 10 5-5. Schematic Diagram MAIN SECTION (3/3) ........ 11 5-6. IC Pin Function Description ..................................... 14
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
6. EXPLODED VIEWS
6-1. Cabinet Section ......................................................... 16 6-2. Optical pick-up Section (CDM-3325ER) ................. 17
: LEAD FREE MARK
Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
7. ELECTRICAL PARTS LIST ................................... 18
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE PART NUMBERS APPEAR AS SHO WN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY .
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
2
D-EJ361/EJ361SR/EJ365 SECTION 1 SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30cm away from the objective lens. Before Replacing the Optical pick-up Block Please be sure to check thoroughly the parameters as per the "Optical pick-up Block Checking Procedure" (Part No. : 9-960-027-11) issued separately before replacing the optical Pick-up block. Note and specifications required to check are given below. · FOK output : IC601 yg pin When checking FOK, remove the lead wire to disc motor. · RF signal P-to-P value : 0.4 to 0.8Vp-p Laser Diode Checking Methods During normal operation of the equipment, emission of the laser diode is prohibited unless the upper panel is closed while turning ON the S809 (push switch type). The following two checking methods for the laser diode are operable. Method : Emission of the laser diode is visually checked. 1. Open the upper lid. 2. Push the S809 as shown in Fig. 1 . 3. Check the object lens for confirming normal emission of the laser diode. If not emitting, there is a trouble in the automatic power control circuit or the optical pick-up. During normal operation, the laser diode is turned ON about 2.5 seconds for focus searching.
S809
Fig.1 Method to push S809
LOCATING THE CONTROLS
CD player (front)
SECTION 2 GENERAL
This section is extracted from instruction manual.
Strap holes DC IN 4.5 V (external power input) jack
OPEN
.>
i (headphones) jack u* SOUN/AVLS x (361/361SR) x /CHG (365) P MODE/ F Display VOL +*/ HOLD
*The button has a tactile dot.
CD player (inside)
Battery Compartment
G-PROTECTION
3
D-EJ361/EJ361SR/EJ365 SECTION 3 DISASSEMBLY
z The
equipment can be removed using the following procedure. Set Upper lid ASSY, Cabinet (upper) sub ASSY Main board MD ASSY "Motor ASSY (Sled) (M902)", Optical pick-up (DAX-25E), "Motor ASSY, turn table (spindle) (M901)"
Note : Follow the disassembly procedure in the numerical order given.
3-1. UPPER LID ASSY, CABINET (UPPER) SUB ASSY
5 Upper lid Assy · CAUTION DURING ASSEMBLY
7 Ten screws (B2) 4 1 2 Spring (L)
2 3 Spring (R) 1 Open
6 0 Cabinet (upper) sub ASSY 9
5
4 1
2 3 Spring (R) 6 Spring (L)
8 Four craws
4
D-EJ361/EJ361SR/EJ365
3-2. MD ASSY, MAIN BOARD
5 MD ASSY 1 CN601
4
2 Connector (CN401) 7 MAIN board 3 Connector (CN402)
6
Cabinet (lower) sub ASSY
3-3. "MOTOR ASSY (SLED) (M902)", OPTICAL PICK-UP (DAX-25E), "MOTOR ASSY, TURN TABLE (SPINDLE) (M901)"
1 Three screws (B1.7x4)
2
3 Cover, Gear 6 8 Three screws (B1.7x4)
5 Motor ASSY (Sled) (M902)
7 Optical pick-up (DAX-25E) 4
0 Motor ASSY, Turn table (Spindle) (M901) 9 Chassis
5
D-EJ361/EJ361SR/EJ365 SECTION 4 ELECTRICAL ADJUSTMENTS
The CD section adjustments are done automatically in this set. Precautions for Check 1. Perform check in the order given. 2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise indicated. 3. Power supply voltage requirement : DC4.5 V in DC IN jack. (J401) VOLUME button : Minimum HOLD switch : OFF Focus bias Check Condition: · Hold the set in horizontal state. Connection:
oscilloscope (AC range) TJ601(RF)
[MAIN BOARD] (SIDE B)
Q601
BCE R608
R604 C610 TJ601 (RF) R611 R601 C412 R409 R603 EXCEPT EJ365 R602 R610 EXCEPT EJ365
C202
L601
R2 C604
C607
C606
14
13
IC602
Procedure: 1. Connect the oscilloscope to the test point TJ601(RF) on the MAIN board. 2. Set a disc. (YEDS-18) 3. Press the u button. 4. Check the oscilloscope waveform is as shown below. A good eye pattern means that the diamond shape () in the center of the waveform can be clearly distinguished.
RF Signal reference Waveform (Eye Pattern)
VOLT/DIV : 100 mV (With the 10 : 1 probe in use) TIME/DIV : 500ns
RF level 0.4 to 0.8 Vp-p
To watch the eye pattern, set the oscilloscope to AC range and increase the vertical sensitivity of the oscilloscope for easy watch-ing.
5. Stop revolving of the disc motor by pressing the x button.
6
C10
12
13
SECTION 5 DIAGRAMS
5-1. BLOCK DIAGRAM
IC602 D-RAM(16M)
XRAS XCAS XWE
D-EJ361/EJ361SR/EJ365
D0-3 1,2,24,25
A0-9 9-12,14-19,6
5 23 4
IC601
OPTICAL PICK-UP BLOCK (DAX-25E) VCC RF OP IC A A E F RF AMP,SERVO DIGITAL SIGNAL PROCESSOR D-RAM CONTROLLER D/A CONVERTER 16 17 87,88,84,85 97-100,96-91,82 90 83 89 HEADPHONE AMP
IC301
A0-A10
D0-D3
RFGO
DETI
XRAS XCAS
XWE
J301
LDACO 31 14 LIN LOUT 8
VCC1_2.2V 13 9 8 6 7 88 RFI A B E F RFDC A/D RF AMP EFM DEMODULATOR
i
SUB CODE PROCESSOR
DAC RDACO 29 15 RIN ROUT 6 EJ365
PWRSW
SERVO
MUTE BEEP
36 DVDDIO 80 SIO PWM CLOCK OSC VCC2_2.0V
19 17 20
OPGSW OPSTB LD LD DRIVER Q601 VCC1_2.2V PD 2 LD APC
86
SCOR XBUSY_O DEFDCT_O
FDOP FDON TDOP TDON SDOP SDON CLVON CLVOP CLKDRV
CLK4M
SDIN SDOUT
XOUT
XIN
GFS FOK O
SRWI
XRST
SCLK
POFF
AVDD2 2.25V 34 40 DVDDV 1.5V 51 VCHK 5
VCC1_2.2V VCPU_1.5V
+V BAT VCPU_2.0V
VCC
5
IC403 (2/2)
POWER CONTROL VCPU_1.5V
PD
3
75 74 77 76 79 78 72 73 71
38
37 44
53
47
49 50
48 45
43 52 64
70 65
FIN+ FINTIN+ TINSIN+ SINCPOL CLVOP SYNC
X601 16.934MHz VCC2_2.0V 18 VCC2
SEM 23 SEO 22 L410
GSW 21 VCC1_2.2V VCPU_2.0V 15 77 11 7 13 71 6 74 30 12 26 17 VCC1 19 VCPU 2.0V VCC 20 VCC0 16 Q404 STNG 25 AD_CHGMNT 22 AD_BATMNT 24 67 CHGMNT 66 VMMNT_O 61 DCIN 62 REGB 63 DET Q401 CHARGE SWITCH 65 CHGB VIN 12 BATM1 68 BATM2 69 DCIN_S 64 L404 LG 8 Q406
2 XIN
FOCUS COIL
F+ FT+
44 42 48 46
FO3 RO3 FO2 RO2 CH2 H BRIDGE LEVEL SHIFTER CH3 H BRIDGE LEVEL SHIFTER
TRACKING COIL
T-
FIN3 60 RIN3 59 FIN1 56 RIN1 55 FIN2 58 RIN2 57 BRK 70 PWM 72 SYNC 34 FG 74 LATCH
79 OPGSW O 78 XOPSTBY_O FIN+ FINSIN+ SINTIN+ TINCPOL SLVOP SYNC
AMUTE_O BEEP_O HPSW_O WP/AD_RMKEY
SCOR_I XBUSY_I DEFECT_I
POFF_O
SRW O
GFS_I FOK_I
+VBAT D405
IC801
SYSTEM CONTROL MICON 72 FG I 14 16 17 18 66 D802 XPOWLT_O SDTI_I SDTO_O SCK_O XWAKEUP_O
M902 SLED MOTOR
S+
M
52 50 6 4 2 80
FO1 RO1 W U V COM CH4 H BRIDGE CH1 H BRIDGE
DRY BATTERY SIZE "AA" (IEC DESIGNATION LR6) 2PCS, 3V
SW
M901 SPINDLE MOTOR
SWITCH Q402, 403 D402 L401
M
V U COM
I/F
40 DATA 39 CLOCK 38 WAKEUP 37 RESETO 35
J401 DC IN 4.5V
!
WP/AD_KEY_1
WP/AD_DCINMNT 27 L402
GPROSW
+VBAT L403
53 49 45 41
VM1 VM12 VM23 VM3
XRST 36
XRST_O 76
56-41 DEFFERENTIAL Q407
60-57
23
25
28
40
38 19 20 VCPU_2.0V
ADVREF
HOLD_I
8 XREST_I
AD_KEY_2
WP/XOPEN
AVCPU
SEG0 I SEG15
COM0 I COM3
1 SPVCC
IC403 (1/2)
FOCUS/TRACKING COIL DRIVE SLED/SPINDLE MOTOR DRIVE
LCD801 LIQUID CRYSTAL DISPLAY
· SIGNAL PATH : CD PLAY
KEY MATRIX S801 S805
| |
S804
S808
S809 (OPEN)
S810 HOLD. OFF ON
S811 G.PROTECTION OFF ON
7
7
D-EJ361/EJ361SR/EJ365
5-2. PRINTED WIRING BOARDS
1 2
· See page 12 for Notes.
3 4
: USES UNLEADED SOLDER.
5
EJ365
6
7
8
9
10
11
12
MAIN BOARD
A
(SIDE A)
J301(1/2) i
J301(2/2) i
MAIN BOARD
(SIDE B)
D201 D306 C301 D101
D302
D301 EJ365
EJ365 C318
S802 SOUND/AVLS R829
R313 FB201 FB303 R302
D308
FB301 R314 C309 FB101 R204 C203 R823 1
R810
S801 P MODE/ 24 C307 R835 R873 S804
IC301
B
FB302 EJ365
C305
+
C308 EXCEPT EJ365 C101 S803
R605 C605
C302
BCE
25 R838 R832 26
1 100
R602 R610 TJ601 (RF) R611 R601 EXCEPT EJ365
C202
C618
C612
R606
15 L601
R201
C614
Q601
R608
C613
12
13 EXCEPT EJ365
C102 C303 R103
VOL
C103
R104
R102 C104
R309
R604 C610 R603
R101
C201 EXCEPT EJ365 R613 C609
R815
R844
C204 R203
C
C607
CN601
IC601
C633 R802 R805 R845 R619 R849 R620 50 51 L604 R631 C629 75 76 C621 C620
OPTICAL PICKUP BLOCK DAX25E
14 13
C412
R409
R616
1
C606 C604
C608R202
S810 X601 C619 ON HOLD
L602 R615 L603
.
t
R612
OFF
C624 R617 R872 R816 R626 R614 C809 L605 R830 R836 C813 C805 R841 R840 R822 C811 C812 S809 (OPEN) R871 LCD801 R827
C632
C622 R628 C626
IC602
R447 C631
R629
ON
S811 G-PROTECTION
D
R446 R814 40 41 21 R859 20 C806
R627
R618
26
1
R630
OFF
IC801
R852 R854
R621 R401 FB405
t
R808 R820 C803 R809 C802 C801
EJ365/EJ361: R804 EXCEPT AEP, EE C810 C807 R825 R427 D802 R812 R833
R858 60 1 61 C804 80 FB408 FB406 C445
C627
C623
E
R404 Q407 BCE R414 C435 C443
LCD801 LIQUID CRYSTAL DISPLAY
C442
C432
C434
· Semiconductor
R448 R801 C427 C437 C436
R434 C430 C409 D409 C441
R436 R440
L411 FB404
C438
C428 L410
C450 R444 C447 R432 R435 R421
L406 D406 C411 R413
C415 R411 R416
C406 Q402
FB401 R428
D410 C433 R425 20
C448 C439 C440 R438
L409 1 2 CN401
ECB
F
Q406 S
R439
D402
C403
Q403 C426 L403
ECB
D404
41
C429
1 R419
60 C404 D403 R403 61 C418 C419 C420 L412 R813 R869 L401 C402 R405 S808 S807 L408 80
1
C425
R864 R811
L407 4
S806
G
VDR402 R408 Q401
x
C423 C422 C421 R863 S805
+
R451
C405
NX
BCE
R407 C410
L402
M
M901 SPINDLE MOTOR
M
M902 SLED MOTOR
DRY BATTERY SIZE "AA" (IEC DESIGNATION LR6) 2PCS, 3V
VDR401
R865
CN402
D405
IC403
C408
E C B
40 FB403 FB402
21
Q404
R423 L404
Ref. No. D101 D201 D301 D302 D306 D308 D402 D403 D404 D405 D406 D409 D410 D802 IC301 IC403 IC601 IC602 IC801 Q401 Q402 Q403 Q404 Q406 Q407 Q601
Location B-4 B-4 B-7 B-4 B-4 B-4 F-8 G-3 F-7 F-8 F-4 F-3 F-10 E-9 B-8 F-9 C-3 D-7 E-2 G-3 F-8 F-8 F-10 F-2 E-3 C-7
R412
>
H J401 DC IN 4.5V 1-685-95512 (12) 1-685-955-
R807
>
12 (12)
8
8
D-EJ361/EJ361SR/EJ365
5-3. SCHEMATIC DIAGRAM MAIN SECTION (1/3) · See page 12 for Notes.
*Q402 CN402 4P 1 M901 COM 2SA1241Y 2SB1237TV2PQR EJ365 EJ361/EJ361SR
S+
T+
T-
R416 220 Q402 * SWITCH
D404 MA111-TX
F+
S-
F-
4
W V U
W V U OPGSW OPSTB L411 47µH C435 22 6.3V
M902
CN401 2P 1 2
FIN+ FINTIN+ TINSIN+ SIN-
L406 47µH
L409 47µH
S+ S-
C438 1
C406 2.2F
15 A B TJ601 (RF)
Q401 2SD1781K CHARGE SWITCH
D405 MA2H735 R403 1
Q403 2SC4116GL SWITCH
R440 47k POWERLT SDTO SCK XWAKE RESET SYNC 1000p 0.047 RESET D409 MA111-TX C427 0.01 C441 0.22 R434 100k Q407 2SC4081T106 DIFFARENTIAL R444 100k
R407 2.2 R436 0 R404 100k
R427 47k
10
LD PD
R408 100
BATMNT CHGMNT
R451 0 C443 1
FOCUS COIL
5
TRACKING COIL
E F F+ TT+ FR601 0 FB404 0 C405 1
CPOL D406 UDZSTE-175.1B R414 0 C418 FG C419 C420 0.022 0.022 C421 C422 C423 0.1
IC403 BH6580KV-F FOCUS/TRACKING COIL DRIVE, SLED/SPINDLE MOTOR DRIVE, POWER CONTROL
C447 C448 R438 10k C440 2200p
XWAKE
C445 1
1 CN601 15P 1-2 2.2V RF 3V A GND CLVOP BUS-2 VCC1 VCPU4
C411 1 FB401 0
4700p 4700p 4700p R435 10k R428 100k C439 220p R432 1k
R439 47k
R421 10k
C442 47 4V
COM R419 10k
C409 1 L410 47µH D410 MA2H735 Q406 CPH3403 SWITCH FB406 0
C410 1 D403 MA2H735 L407 100µH Q404 2SB167900LSO SWITCH C436 47 4V C434 47 4V
W
U
V
L403 47µH DRY BATTERY SIZE"AA" (IEC DESIGNATION LR6) 2PCS,3V DCINMNT D402 MA2H735 VDR402 R411 220k J401 C402 L401 1 4.7µH L408 0 C404 1000p R412 47k FB403 0 FB402 0 C415 0.22 R413 47k
C425 22 10V
L404 220µH
R425 0
C433 1
R423 0 FB408 0
C403 10 16V C426 220 6.3V
C429 0.1 C428 4.7 25V
C408 470p C432 220 4V
C437 47 4V
C450 1
FB405 0
C430 1
VDR401
R405 0
L402 4.7µH
L412 0
POWER GND
9
9
VCPU 2V D GND2 VCC2
D GND AU GND
B1
D-EJ361/EJ361SR/EJ365
5-4. SCHEMATIC DIAGRAM MAIN SECTION (2/3) · See page 12 for Notes.
FOK DEFECT
CPOL SYNC GFS
R627 100k
A3 A2 A1
FIN+ FIN-
R629 0
L604 10µH
C629 47p
C626 0.1
R630 0
R621 0
TINTIN+ SINSIN+ C620 0.1 A10 XCAS D2 D3 D0 D1 XWE XRAS A9 A8 A7 A6 A5 A4 A0 A1 A2 A3 IC601 BU9354KV RF AMP,SERVO, DIGITAL SIGNAL PROCESSOR D-RAM CONTROLLER D/A CONVERTER C633 100 6.3V R616 1M
R619 R620 R618
470 470 470
SDTI SDTO SRW SCK POFF XRST SCOR
L605 0
R626 0
C622 R628 10k
0.01
R401 10
C632 R615 0.1 0
C619 10p
C624 10p
C627 22 4V
C623 1
C621 0.1
L602 X601 16.934MHz 0 R102 *2 C104 470p R202 *2 R103 *3
L603 0
IC301 TA2120FN HEADPHONE AMP
R614 C101 R101 47 *1 10k EXCEPT EJ365 C201 R201 *1 10k C618 2.2 *1
C102 0.001 BEEP R203 C202 *3 0.001 C303 0.47 AMUTE HPSW R104 4.7 C307 10 16V C305 0.1 C103 0.1 C302 2.2 C309 220 6.3V C308 10 16V R302 0
FB303 FB101 J301 FB201 D308 MA3J14700
C204 470p EXCEPT EJ365
100k 100k 100k 100k
R606 0
C614 2200p R612 0 C613 0.01 C612 1000p C605 1000p C607 0.1 C608 0.22
C101, 201 2.2 EJ361:AEP, EE 1 EJ361:AUS, C&SA, CND, E18 MX, TW/EJ361SR/EJ365 R446 0
R204 4.7 C203 0.1
XCAS D2 D3
A4 A5 A6 A7 A8
R617 0
A9 XRAS XWE D1 D0
A0
R631 2.2k
CLK4M XBUSY
R448 0
EJ365 C301 0.01 D301 MA8130
R613 470 C609 1
PD
R611 2.2k
LD
*2 R102, 202 47K EJ361:AEP, EE 4.7K EJ361:AUS, C&SA, CND, E18 MX, TW/EJ361SR/EJ365 *3 R103, 203 4.7K EJ361:AEP, EE 10K EJ361:AUS, C&SA, CND, E18 MX, TW/EJ361SR/EJ365
D302 MA8130 D101 MA8130-TX
D306 MA8130
BATMNT R602 E R603 F R604 B R605 A
R309 4.7
D201 MA8130-TX
R313 10k C318 0.001 FB301
R314 1k RMKEY
R610 100k L601 10µH R608 2.2 C610 4.7 R447 0
C631 0.1
C604 0.1
C606 10 16V
FB302
Q601 2SB167900LSO LD DRIVER
C412 47 6.3V
R409 2.2 EJ365
RF
VCC1
A GND
3V
POWER GND
AU GND
10
10
VCPU 2V
D GND
CLVOP BUS-2
VCPU4
D GND2
VCC2 B1
2.2V
1-2
D-EJ361/EJ361SR/EJ365
5-5. SCHEMATIC DIAGRAM MAIN SECTION (3/3) · See Page 12 for Notes.
VCC2 B1
BATMNT
DCINMNT
CHGMNT
VCPU 2V AU GND
*C811 10k 470p
BEEP
EJ361/EJ361SR EJ365 RMKEY
HOLD
G-PRO
OPEN
R840 0
470 470 0 470
R827 470 R830 0 R832 R833 R836 R838
R841 100k
R845 10k
*R804 47k 22k
EJ365 EJ361: AUS, C&SA, CND. E18, MX, TW/EJ361SR 0.1 0.01 0.1 0.01 * 0.01 OPEN S809 (OPEN)
R802 1k
C805 C812 C813 C814 C811 C809 R804 * TAP806
R805 1k
R871 220k C806 0.01 C808 4700p TAP805 R816 10k
LCD801 LIQUID CRYSTAL DISPLAY
SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 COM3 COM2 COM1 COM0
SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 COM3 COM2 COM1 COM0
OPEN:NORMAL MODE SHORT:TEST MODE SCK SDTO SDTI SRW POWERLT DEFECT HPSW SCOR RESET RESET2 XBUSY FOK TEST C810 0.1 C807 0.22 CLK4M
HOLD R872 10k G-PRO
OFF ON ON OFF
S810 HOLD S811 G-PROTECTION
R849 470
R852 470 R854 0 IC801 T5AW6-Z7C SYSTEM CONTROL MICON D802 MA2ZD14001S0
S805
S806
S807
S808
R858 470 R859 470
R864 2.2k R863 R811 10k 22k
R865 2.2k
R869 10k R813 22k
R823 10k R809 100k S802 SOUND/AVLS R829 2.2k R835 2.2k R844 10k R815 22k R873 22k S803 VOLS804 VOL+ S801 P MODE/
C802 0.1
C804 0.22
R820 470 R822 470
R825 470 R812 470
C801 0.1
R810 22k
XWAKE PGM_SDTO PGM_SDTI PGM_SCK
GFS FG PGM_SEL AMUTE
XRST POFF OPSTB OPGSW
D GND2 D GND POWER GND
C803 0.1 R801 0 R808 100k
R807 0
11
11
D-EJ361/EJ361SR/EJ365
For schematic diagrams.
Note: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specifed. : internal component. · f Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · A : B+ Line. · Power voltage is dc 4.5 V and fed with regulated dc power supply from battery terminal. · Voltages are dc with respect to ground under no-signal conditions. no mark : PLAY · Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. · Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production toler ances. · Circled numbers refer to waveforms. · Signal path. E : CD PLAY · Abbreviation CND : Canadian AUS : Australian MX : Mexican TW : Taiwan C&SA : Central and South America HK : Hong Kong CH : Chinese EE : East European E18 : 100-240V area
Note on Printed Wiring Boards: Note: · X : parts extracted from the component side. · a : Through hole. : Pattern from the side which enables seeing. · (The other layers' patterns are not indicated.) Caution: Pattern face side :Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side : Parts on the parts face side seen from the (Side A) parts face are indicated.
· IC BLOCK DIAGRAM
IC301 TA2120FN (EL)
BST OUT 24 BB SW 23 BIAS IN BIAS 21 22 BIAS PWR SW 20 PW SW MUTE MUTE SW TC 19 18 MT SW BEEP 17 BEEP OUT B OUT A GND 16 RIN 15
ALC
LIN 14
ALC
ATT SW 13 ATT SW
ADDB
· Abbreviation CND : Canadian AUS : Australian MX : Mexican TW : Taiwan C&SA : Central and South America HK : Hong Kong CH : Chinese EE : East European E18 : 100-240V area
+
BST
ADDA
+
+
PW B
PW C
PW A
PWC SW
ALC DET
1 BST NF
2 ADD OUT
3 4 RF IN OCL SW
5 VCC
6
7
8 LOUT
9
10
11 ALC IN
12 ALC DET
ROUT VREF
PWR MIX GND OUT
IC601
BU9354KV
A3 A2 A1 A0 A4 A5 A6 A7 A8 A9 RASB WEB D1 D0 DVDDIO2 D3 D2 CAS1B A10/CAS2B DVSSIO2 DVDDIO SDOP SDON TDOP TDON
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 AVDD1 LD PD VMON VCHK 1 2 3 4 5
APC A/D ESP PWM 75 74 73 72 FDOP FDON CLVOP CLVON
r Waveforms
1
2.0 Vp-p
4
2.0 Vp-p
16.934 MHz
5.7 µsec
IC403 qd DSW
VOLT/DIV : 1 V AC TIME/DIV : 2 µsec
IC601ek XOUT
VOLT/DIV : 1 V AC TIME/DIV : 50 nsec
VE VF VBD VAC AVSS1 VBIAS N.C. RF1 PKC BTC RFGO DETI ASYI ASYO MON1 MON2 ADPFO ADPFI FCO PCO
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
71 CLKDRV 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 1bit DAC CLOCK GEN SUB SIO SYNC EXPLCK TEST_S EFM/YFLG C2FX FOK DEFECT LRCKI DOUTAI LRCKO DOUTAO DOCKO TEST N.C. N.C. N.C. N.C. CLK4M BUSYB DVDD
SERVO CORE RF AMP FLAG
WINDOW D/A
ECC
2
2.0 Vp-p
5
2.3 Vp-p
PLL
5.7 µsec
0.237 µsec
VOLT/DIV : 1 V AC TIME/DIV : 2 µsec
IC403 ef SYNC
IC601 td CLK4M
VOLT/DIV : 1 V AC TIME/DIV : 0.2 µsec
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
AVSS2 RLINO RLINI RDACO VCDACO LDACO LLINI LLINO AVDD2 MUTE DVDD1 XIN XOUT DVSSIO DVDD DOCKI DVSS1 SBSY
44 45 46
RSTB PDWNB DVSSIO
47 48 49 50
SCLK SRW SDIN SDOUT
3
0.4 to 0.8Vp-p
6
2.3 Vp-p
0.237 µsec
TJ601 (RF)
VOLT/DIV : 0.5 V AC TIME/DIV : 0.5 µsec
IC801 2 XIN
VOLT/DIV : 1 V AC TIME/DIV : 0.2 µsec
12
12
D-EJ361/EJ361SR/EJ365
IC403
BH6580KV
PGND1 PGND2 VM12 VM23 0GND PGND3 RIN3 FIN2 RIN2 FIN1 RIN1 FIN3 VM1 RO1 RO2 FO1 FO2 VM3 41 RO3 42 FO3 44
60 59 58 57 56 55
54
53
52
51
50
49
48
47
46
45
43
CH1 H BRIDGE DCIN 61 REGB 62 CONTROLLER DET 63 DCIN_S 64 CHGB 65 VMMNT 66 CHARGE VM VCC HVPROT LEVEL SHIFTER VG
CH2 H BRIDGE
CH3 H BRIDGE 40 LATCH 39 DATA 38 CLOXK 37 WAKEUP 36 XRST RESET 35 RESET_O 34 SYNC
CHGMNT 67 33 PREGND MONTOR AMP SAW GEN BATM1 68 BATM2 69 BBK 70 PREGND 71 PWM 72 SOFTPWM 73 FG 74 CSL2 75 CSL1 76 WI 77 VI 78 UI 79 PRE DRIVE COM 80 21 GSW 1 SPVCC1 2 U_OUT 3 SPGND1 4 V_OUT 5 SPVCC2 6 W_OUT 7 SPGND2 8 LG 9 10 VG SSW 11 VCC3 12 VIN 13 DSW 14 POWERGND 15 USW 16 VCC0 17 VCC1 18 VCC2 19 VCPU_2.0V 20 VCC LOGIC VG VG VCC3 VG VCC4 VG 23 SEM 22 SEO SLOPE SIGNAL VCC INPUT SELECT VCC 30 EI 29 EO 28 VCC2NF 27 VCPUNF 26 PMG 25 STNG VCC2 CLK 32 SOFT 10msec DELAY 31 SLOW
INTERFACE
24 SEP
13
D-EJ361/EJ361SR/EJ365
5-6. IC PIN FUNCTION DESCRINTION
IC801 (SYSTEM CONTROL) T5AW6-Z7C Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 to 56 57-60 61-63 64 65 66 67 Pin name GND XIN XOUT TEST VCPU_2.0V FOK_I XBUSY_I RESET_I ACKCD_I DEFECT CTRL_O SCOR_I HPSW_O DEFECT_I XPOWLT_O SRW_O SDTI_I SDTO_O SCK_O AVCPU ADVREF AD_SEL AD_CHGMNT AD_KEY2 AD_BATTMNT WP/AD_KEY1 WP/AD_RMKEY AD_DCINMNT WP/XOPEN TUPWR BEEP_O NC VDD_EEPROM WP/K2_RM TU_ON_I INSW X4M/16M_I XL_O GPROSW_I LCD_REQ_O HOLD_I SEG0-15 COM0-3 V1-3 C1 C0 XWAKEUP_O PGM_SDTO I/O I O I I I I/O I O I O I O O I O O I I I I I I I I O O O O I O I O I O I O O O Ground terminal System clock input Not used (OPEN) Test mode terminal Power supply for CPU & I/O Focus OK signal input DSP's auto sequencer status Micon reset terminal Not used (FiXed to L) Not used (OPEN) SCOR pulse input Headphone IC power switch DEFECT signal input Power IC's serial interface latch output DSP's serial interface Read/Write signal output Serial interface input Serial interface output Serial interface clock output Power supply for CPU and I/O Analog reference voltage for A/D converter Test mode detection input Charging monitor input Key input Battery voltage monitor input Set's key detection input Remocon's key detection input DC voltage monitoring input OPEN switch status detection input Not used (OPEN) BEEP sound Not used (OPEN) Power supply for EEPROM (OPEN) Not used (OPEN) Not used (fixed at L) Not used (OPEN) DRAM size selection terminal (fixed at H) Not used (OPEN) ESP switch status detection input Not used (OPEN) HOLD switch status detection input LCD segment output LCD common output LCD driver booster LCD driver booster LCD driver booster Wale-up signal output Not used (OPEN) Description
14
D-EJ361/EJ361SR/EJ365
Pin No. 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin name PGM_SDTI PGM_SCK_O CD_ON GFS_I FG_I PGMSEL_O AMUTE_O RESET_TU_O XREST_O POFF_O XOPSTBY_O OPGSW_O C2POEN_O
I/O O I I O O O O O O O Not used (OPEN) Not used (OPEN) Not used (OPEN)
Description
Guard Frame Synchronous signal input FG signal input Not used (OPEN) Mute ON/OFF control output Not used (OPEN) System reset output DSP's power off output Pick-up's power supply ON/OFF control RF IC's gain control Not used (OPEN)
15
D-EJ361/EJ361SR/EJ365 SECTION 6 EXPLODED VIEWS
NOTE : · -XX, -X mean standardized parts, so they may have some difference from the original one. · Color indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ··· (RED) Parts color Cabinet's color · Items marked " * "are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. · Abbreviation CND : Canadian AUS : Australian MX : Mexican TW : Taiwan C&SA : Central and South America HK : Hong Kong CH : Chinese EE : East European E18 : 100-240V area The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
6-1. CABINET SECTION
CDM-3325ER
4 5 3
LCD801
12
10 6 7 11 13 14 8
2
15 16
1
Ref. No. 1 1 2 * 3 * 3
Part No. X-3383-002-1 X-3383-199-1 3-248-574-01 A-3347-968-A A-3347-972-A
Description Remark CABINET (LOWER) SUB ASSY (SILVER) CABINET (LOWER) SUB ASSY (BLUE) SHEET, SHIELD MAIN BOARD, COMPLETE (EJ361:AEP,EE) MAIN BOARD, COMPLETE (EJ365)
Ref. No. 12 12
Part No. Description Remark X-3383-113-1 LID ASSY, UPPER (SILVER) (EJ365) X-3383-201-1 LID ASSY, UPPER (SILVER) (EJ361:AEP,AUS,CND,EE,MX,TW) X-3383-202-1 LID ASSY, UPPER (BLUE) (EJ361:AEP,AUS,C&SA,CND,E18,EE,MX) X-3383-203-1 LID ASSY, UPPER (SILVER) (EJ361:E18/EJ361SR) X-3383-204-1 LID ASSY, UPPER (BLUE) (EJ365) 3-248-061-01 SPRING (L) 3-248-062-01 SPRING (R) X-3383-291-1 X-3383-292-1 3-246-595-01 A-3364-797-A CABINET (UPPER) SUB ASSY (EJ361/EJ361SR) CABINET (UPPER) SUB ASSY (EJ365) LID, BATTERY CASE LCD ASSY
12 12 12 13 14 15 15 16 LCD801
* 3
4 5 6 7 8 10 11
A-3683-758-A MAIN BOARD, COMPLETE (EJ361:AUS,C&SA,CND,E18,MX,TW/EJ361SR) 3-249-578-01 KNOB (GPRO) 3-831-441-99 SPACER, KNOB 3-246-653-01 TERMINAL BOARD (+), BATTERY 3-246-654-01 TERMINAL BOARD (-), BATTERY 3-247-456-01 BOARD (RELAY),TERMINAL,BATTERY 3-245-331-01 INSULATOR 4-908-792-61 SCREW (B2)
16
D-EJ361/EJ361SR/EJ365
6-2. OPTICAL PICK-UP SECTION (CDM-3325ER)
103
104 102 106
M902
M901
107 105
109
108 110 101 111 101
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. Ref. No. 101 102 103 104 105 106 0 107 Part No. 3-318-203-61 3-221-474-01 3-221-472-02 A-3180-952-A 3-221-473-01 Description SCREW (B1.7X4), TAPPING SPRING, SLED CHASSIS FEED ASSY, SCREW COVER, GEAR Remark Ref. No. 108 109 110 111 M901 M902 Part No. 3-221-475-01 3-222-298-01 3-222-299-01 Description SHAFT, STANDARD RACK SPRING, RACK RETAINER Remark
3-221-268-01 GEAR (B) X-3380-950-1 OPTICAL PICK-UP (DAX-25E RP ASSY) (DAX-25E)
3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN A-3180-953-A MOTOR ASSY, TURN TABLE (SPINDLE) A-3180-951-A MOTOR ASSY, SLED (including GEAR)
17
D-EJ361/EJ361SR/EJ365 MAIN
NOTE : · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX, -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms METAL : Metal-film resistor METAL OXIDE :Metal oxide-film resistor F : nonflammable · Items marked " * "are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
SECTION 7 ELECTRICAL PARTS LIST
· SEMICONDUCTORS In each case, u : µ , for example : uA.... : µ A.... , uPA.... : µ PA.... uPB.... : µ PB.... , uPC.... : µ PC.... uPD.... : µ PD.... · CAPACITORS uF : µ F · COILS uH : µ H · Abbreviation CND : Canadian AUS : Australian MX : Mexican TW : Taiwan C&SA : Central and South America HK : Hong Kong CH : Chinese EE : East European E18 : 100-240V area Remark Ref. No. C410 C411 C412 C415 C418 C419 C420 C421 C422 C423 C425 C426 C427 C428 C429 C430 C432 C433 C434 C435 C436 C437 C438 C439 C440 C441 C442 C443 C445 C447 C448 C450 C604 C605 C606 C607 C608 C609 C610 C612 C613 C614 C618 C619 Part No. 1-115-156-11 1-115-156-11 1-110-569-11 1-115-467-11 1-107-826-11 1-164-227-11 1-164-227-11 1-162-968-11 1-162-968-11 1-162-968-11 1-104-852-11 1-126-369-11 1-162-970-11 1-135-970-21 1-164-156-11 1-115-156-11 1-124-434-00 1-115-156-11 1-124-589-11 1-135-852-21 1-124-589-11 1-124-589-11 1-125-837-91 1-162-966-11 1-162-966-11 1-115-467-11 1-124-589-11 1-125-837-91 1-125-837-91 1-162-964-11 1-165-176-11 1-115-156-11 1-164-156-11 1-162-964-11 1-104-913-11 1-107-826-11 1-115-467-11 1-125-837-91 1-117-720-11 1-162-964-11 1-162-970-11 1-162-966-11 1-135-834-91 1-162-915-11 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
Description CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP ELECT CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 1uF 47uF 0.22uF 0.1uF 0.022uF 0.022uF 0.0047uF 0.0047uF 0.0047uF 22uF 220uF 0.01uF 4.7uF 0.1uF 1uF 220uF 1uF 47uF 22uF 47uF 47uF 1uF 0.0022uF 0.0022uF 0.22uF 47uF 1uF 1uF 0.001uF 0.047uF 1uF 0.1uF 0.001uF 10uF 0.1uF 0.22uF 1uF 4.7uF 0.001uF
Remark 10V 10V 6.3V 10V 16V 25V 25V 50V 50V 50V 10V 6.3V 25V 25V 25V 10V 4V 10V 16V 6.3V 16V 16V 6.3V 50V 50V 10V 16V 6.3V 6.3V 50V 16V 10V 25V 50V 16V 16V 10V 6.3V 50V 25V 50V 6.3V 50V
* * *
A-3347-968-A MAIN BOARD, COMPLETE (EJ361:AEP,EE) A-3347-972-A MAIN BOARD, COMPLETE (EJ365) A-3683-758-A MAIN BOARD, COMPLETE (EJ361:AUS,C&SA,CND,E18,MX,TW/EJ361SR)
*******************
3-246-653-01 TERMINAL BOARD (+), BATTERY 3-246-654-01 TERMINAL BOARD (-), BATTERY 3-254-514-01 SHEET (LCD), SHIELD (EJ361:AUS,C&SA,CND,E18,MX,TW/EJ361SR) < CAPACITOR > C101 C101 1-125-838-11 CERAMIC CHIP 1-109-982-11 10% 6.3V (EJ361:AEP,EE) CERAMIC CHIP 1uF 10% 10V (EJ361:AUS,C&SA,CND,E18,MX, TW/EJ361SR/EJ365) CERAMIC CHIP 0.001uF 10% 50V CERAMIC CHIP 0.1uF 10% 16V CERAMIC CHIP 470PF 10% 50V (EJ361:AUS,C&SA,CND,E18,MX,TW/EJ361SR) 10% 6.3V (EJ361:AEP,EE) CERAMIC CHIP 1uF 10% 10V (EJ361:AUS,C&SA,CND,E18,MX, TW/EJ361SR/EJ365) CERAMIC CHIP 0.001uF 10% 50V CERAMIC CHIP 0.1uF 10% 16V CERAMIC CHIP 470PF 10% 50V (EJ361:AUS,C&SA,CND,E18,MX,TW/EJ361SR) 0.01uF 2.2uF 0.47uF 0.1uF 10uF 10uF 220uF 0.001uF 1uF 10uF 0.001uF 1uF 2.2F 470PF 1uF 50V 6.3V 6.3V 16V 16V 16V 6.3V 50V (EJ365) 10V 16V 50V 10V 6.3V 50V 10V 2.2uF 2.2uF
20% 10% 10% 10% 10% 10% 10% 10% 20% 20% 10% 20%
C102 C103 C104
1-162-964-11 1-107-826-11 1-162-962-11
20% 20% 20% 20% 20% 10% 10% 10% 10% 20% 10% 10% 10% 10%
C201 C201
1-125-838-11 CERAMIC CHIP 1-109-982-11
C202 C203 C204
1-162-964-11 1-107-826-11 1-162-962-11
C301 C302 C303 C305 C307 C308 C309 C318 C402 C403 C404 C405 C406 C408 C409
1-162-974-11 1-125-838-11 1-117-863-11 1-107-826-11 1-104-913-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
10% 10% 10% 20% 20% 20% 10%
1-104-913-11 TANTAL. CHIP 1-126-369-11 ELECT 1-162-964-11 CERAMIC CHIP 1-115-156-11 CERAMIC CHIP 1-104-913-11 TANTAL. CHIP 1-162-964-11 1-115-156-11 1-135-834-91 1-162-962-11 1-115-156-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10% 20% 10% 10% 10% 10V 10%
20% 10%
10%
0.01uF 10% 0.0022uF 10% 2.2F 10PF 0.5PF
18
D-EJ361/EJ361SR/EJ365 MAIN
Ref. No. C620 C621 C622 C623 C624 C626 C627 C629 C631 C632 C633 C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C811 C812 C813 C814 Part No. Description 1-164-156-11 CERAMIC CHIP 1-164-156-11 1-162-970-11 1-125-837-91 1-162-915-11 1-164-156-11 1-104-847-11 1-162-923-11 1-164-156-11 1-164-156-11 1-128-964-91 1-164-156-11 1-164-156-11 1-164-156-11 1-115-467-11 1-162-970-11 1-162-974-11 1-115-467-11 1-162-968-11 1-162-970-11 1-164-156-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.01uF 1uF 10PF 0.1uF 22uF 47PF 0.1uF 0.1uF 100uF 0.1uF 0.1uF 0.1uF 0.22uF 0.01uF Remark 25V 25V 25V 6.3V 50V 25V 4V 50V 25V 5V 6.3V 25V 25V 25V 10V 25V 50V 10V 50V 25V 25V Ref. No. FB408 Part No. Description 1-216-864-11 METAL CHIP < IC > IC301 IC403 IC601 IC602 IC801 8-759-681-65 6-703-034-01 6-703-033-01 6-703-609-01 6-802-331-01 IC TA2120FN(EL) IC BH6580KV IC BU9354KV IC MSM51X4400E-10TSK-FS IC T5AW6-Z7C < JACK > J301 J301 J401 1-815-088-41 JACK, HEADPHONE () (EJ365) 1-815-135-32 JACK, HEADPHONE () (EJ361/EJ361SR) 1-778-153-21 JACK,DC(POLARITY UNIFIED TYPE) (DC IN 4.5V) < COIL > 0 5% Remark 1/10W
10% 10% 0.5PF
20% 5% 2 20%
10% 10%
* L401
0.01uF 0.22uF 10% 0.0047uF 10% 0.01uF 10% 0.1uF 470PF 10K 0.01uF 0.1uF 0.01uF 10% L402 L403 L404 L406 L407 L408 L409 L410 L411 L412 L601 L602 L603 L604 L605
1-400-373-21 1-400-373-21 1-400-145-21 1-414-406-41 1-400-145-21 1-419-387-21 1-216-296-11 1-400-145-21 1-400-145-21 1-414-402-11 1-216-296-11 1-469-967-21 1-216-295-91 1-216-295-91 1-469-570-21
INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR SHORT CHIP INDUCTOR INDUCTOR INDUCTOR SHORT CHIP INDUCTOR SHORT CHIP SHORT CHIP INDUCTOR
4.7uH 4.7uH 47uH 220uH 47uH 100uH 0 47uH 47uH 47uH 0 10uH 0 0 10uH 0
1-162-962-11 CERAMIC CHIP 1-216-833-11 METAL CHIP 1-162-970-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP < CONNECTOR >
50V (EJ365) 5% 1/10W (EJ361/EJ361SR) 10% 25V 10% 16V 10% 25V
CN401
* CN402 * CN601
1-784-342-21 HOUSING, CONNECTOR 2P 1-785-877-21 HOUSING, CONNECTOR 4P 1-816-237-21 CONNECTOR, FFC/FPC (ZIF) 15P < DIODE >
1-216-295-91 SHORT CHIP
< LIQUID CRYSTAL DISPLAY > LCD801 A-3364-797-A LCD ASSY D101 D201 D301 D302 D306 D308 D402 D403 D404 D405 D406 D409 D410 D802 8-719-420-87 8-719-420-87 8-719-420-87 8-719-420-87 8-719-420-87 8-719-059-53 8-719-067-42 8-719-067-42 8-719-404-50 8-719-067-42 8-719-069-54 8-719-404-50 8-719-067-42 8-719-072-70 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE MA8130 MA8130 MA8130 MA8130 MA8130-TX (EJ365) MA3J14700LSO MA2H735-(TX).SO MA2H735-(TX).SO MA111-TX MA2H735-(TX).SO UDZSTE-175.1B MA111-TX MA2H735-(TX).SO MA2ZD14001S0 < TRANSISTOR > Q401 Q402 Q402 Q403 Q404 Q406 Q407 Q601 8-729-921-73 TRANSISTOR 2SD1781K-QR 8-729-052-27 TRANSISTOR 2SA1241-Y(LBSONY) (EJ365) 6-550-070-01 TRANSISTOR 2SB1237TV2PQR (EJ361/EJ361SR) 8-729-231-74 TRANSISTOR 2SC4116-GL 8-729-054-79 TRANSISTOR 2SB167900LSO 8-729-044-84 TRANSISTOR CPH3403-TL-E 8-729-905-40 TRANSISTOR 2SC4081T106 8-729-054-79 TRANSISTOR 2SB167900LSO < RESISTOR > R101 R102 R102 5% 1/10W 5% 1/10W (EJ361:AEP,EE) 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (EJ361:AUS,C&SA,CND,E18,MX, TW/EJ361SR/EJ365) 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (EJ361:AEP,EE) 1-216-833-11 METAL CHIP 10K 5% 1/10W (EJ361:AUS,C&SA,CND,E18,MX, TW/EJ361SR/EJ365) 1-216-793-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-841-11 METAL CHIP 4.7 10K 47K 5% 1/10W 5% 1/10W 5% 1/10W (EJ361:AEP,EE) 1-216-833-11 METAL CHIP 1-216-841-11 METAL CHIP 10K 47K
< FERRITE BEAD > FB101 FB201 FB301 FB302 FB303 FB401 FB402 FB403 FB404 FB405 FB406 1-500-234-22 1-500-234-22 1-469-152-11 1-469-152-11 1-500-234-22 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 FERRITE FERRITE FERRITE FERRITE FERRITE METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0uH 0uH 0uH (EJ365) 0uH (EJ365) 0uH 0 0 0 0 0 0 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
R103 R103
R104 R201 R202
1-216-864-11 METAL CHIP
19
D-EJ361/EJ361SR/EJ365 MAIN
Ref. No. R202 Part No. Description Remark Ref. No. R620 R621 R626 R627 R628 R629 R630 R631 R801 R802 R804 R804 R314 R401 R403 R404 R405 R407 R408 R409 R411 R412 R413 R414 R416 R419 R421 R423 R425 R427 R428 R432 R434 R435 R436 R438 R439 R440 R444 R446 R447 R448 R451 R601 R602 R603 R604 R605 R606 R608 R610 R611 R612 R613 R614 R615 R616 R617 R618 R619 1-216-821-11 METAL CHIP 1-216-797-11 1-218-446-11 1-216-845-11 1-216-864-11 1-216-789-11 1-216-809-11 1-216-789-11 1-218-903-11 1-218-887-11 1-216-841-11 1-216-864-11 1-216-813-11 1-216-833-11 1-216-833-11 1-216-864-11 1-216-295-91 1-216-841-11 1-216-845-11 1-216-821-11 1-216-845-11 1-216-833-11 1-216-864-11 1-216-833-11 1-216-841-11 1-216-841-11 1-216-845-11 1-216-864-11 1-216-864-11 1-216-295-91 1-216-864-11 1-216-864-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-864-11 1-216-789-11 1-216-845-11 1-216-825-11 1-216-864-11 1-216-817-11 1-216-805-11 1-216-864-11 1-216-857-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10 1 100K 0 2.2 100 2.2 220K 47K 47K 0 220 10K 10K 0 0 47K 100K 1K 100K 10K 0 10K 47K 47K 100K 0 0 0 0 0 100K 100K 100K 100K 0 2.2 100K 2.2K 0 470 47 0 1M 0 470 470 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W (EJ365) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W R829 R830 R832 R833 R835 R836 R838 R840 R841 R844 R845 R849 R852 R854 R858 R859 R863 R864 R865 R869 R871 R872 R873 1-218-855-11 1-216-864-11 1-216-817-11 1-216-817-11 1-216-825-11 1-216-864-11 1-216-817-11 1-216-864-11 1-216-845-11 1-216-833-11 1-216-833-11 1-216-817-11 1-216-817-11 1-216-864-11 1-216-817-11 1-216-817-11 1-218-871-11 1-218-855-11 1-216-825-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 0 470 470 2.2K 0 470 0 100K 10K 10K 470 470 0 470 470 10K 2.2K 2.2K 10K 220K 10K 22K 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W Part No. Description 470 0 0 100K 10K 0 0 2.2K 0 1K 47K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 4.7K 5% 1/10W (EJ361:AUS,C&SA,CND,E18,MX, TW/EJ361SR/EJ365) 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (EJ361:AEP,EE) 1-216-833-11 METAL CHIP 10K 5% 1/10W (EJ361:AUS,C&SA,CND,E18,MX, TW/EJ361SR/EJ365) 4.7 5% 1/10W 0 4.7 5% 1/10W 10K 0.5% 1/10W (EJ365) 1-216-829-11 METAL CHIP 1-216-817-11 METAL CHIP 1-216-864-11 METAL CHIP 1-216-864-11 1-216-845-11 1-216-833-11 1-216-864-11 1-216-864-11 1-216-825-11 1-216-295-91 1-216-821-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
R203
R203
R204 R302 R309 R313
1-216-793-11 1-216-295-91 1-216-793-11 1-218-871-11
METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
1/10W 1/10W (EJ365) 1-216-837-11 METAL CHIP 22K 5% 1/10W (EJ361:AUS,C&SA,CND,E18,MX,TW/EJ361SR) METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 0 100K 100K 22K 22K 470 22K 22K 10K 470 470 10K 470 470 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
R805 R807 R808 R809 R810 R811 R812 R813 R815 R816 R820 R822 R823 R825 R827
1-216-821-11 1-216-864-11 1-216-845-11 1-216-845-11 1-216-837-11 1-216-837-11 1-216-817-11 1-216-837-11 1-216-837-11 1-216-833-11 1-216-817-11 1-216-817-11 1-218-871-11 1-216-817-11 1-216-817-11
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-849-11 METAL CHIP 1-218-871-11 METAL CHIP 1-216-837-11 METAL CHIP < SWITCH >
S801 S802 S803 S804 S805 S806 S807
1-786-211-21 1-786-211-21 1-786-211-21 1-786-211-21 1-786-211-21
SWITCH, KEYBOARD (P MODE/ F) SWITCH, KEYBOARD (SOUND/AVLS) SWITCH, KEYBOARD (VOL-) SWITCH, KEYBOARD (VOL+) SWITCH, KEYBOARD (u)
1-216-864-11 METAL CHIP 1-216-817-11 METAL CHIP 1-216-817-11 METAL CHIP
1-786-211-21 SWITCH, KEYBOARD (x) 1-786-211-21 SWITCH, KEYBOARD (.)
20
D-EJ361/EJ361SR/EJ365 MAIN
Ref. No. S808 S809 S810 S811 Part No. 1-786-211-21 1-786-275-11 1-771-586-11 Description Remark SWITCH, KEYBOARD (>) SWITCH, PUSH (1 KEY) (OPEN/CLOSE) SWITCH, SLIDE (HOLD .)
1-553-977-00 SWITCH, SLIDE (G-PROTECTION) < VARISTOR >
VDR401 1-801-862-11 VARISTOR, CHIP 1608) VDR402 1-801-862-11 VARISTOR, CHIP (1608) < VIBRATOR > X601 1-795-561-21 VIBRATOR, CERAMIC (16.934MHz)
*****************************************************
MISCELLANEOUS
*************
0 107 X-3380-950-1 OPTICAL PICK-UP (DAX-25E RP ASSY) (DAX-25E) LCD801 A-3364-797-A LCD ASSY M901 A-3180-953-A MOTOR ASSY, TURN TABLE (SPINDLE) M902 A-3180-951-A MOTOR ASSY, SLED (including GEAR) ACCESSORIES
***************************************************** **********
0 0 0 0 0 1-477-499-21 ADAPTOR, AC (AC-ES455K) (EJ365:CH) 1-477-500-21 ADAPTOR, AC (AC-ES455K) (EJ361:AEP,EE,E18/EJ361SR/EJ365:E18) 1-477-501-21 ADAPTOR, AC (AC-ES455K) (EJ365:HK) 1-477-502-21 ADAPTOR, AC (AC-ES455K) (EJ361:C&SA,CND,MX,TW) 1-477-503-21 ADAPTOR, AC (AC-ES455K) (EJ361:AUS) 1-477-524-11 REMOTE COMMANDER (RM-MC20) (EJ365) 1-756-307-21 BATTERY, NICKEL.HYDRIGEN (EJ365) 3-248-746-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH, SPANISH) (EJ361:AEP,AUS,C&SA,CND,MX/EJ361SR) 3-248-746-21 MANUAL, INSTRUCTION (DUTCH, SWEDISH, PORTUGUESE) (EJ361:AEP,C&SA) 3-248-746-31 MANUAL, INSTRUCTION (GERMAN, ITALIAN, FINNISH) (EJ361:AEP) 3-248-746-41 MANUAL, INSTRUCTION (HUNGARIAN, RUSSIAN) (EJ361:EE) 3-248-746-51 MANUAL, INSTRUCTION (POLISH, CZECH, SLOVAKIAN) (EJ361:EE) 3-249-120-12 MANUAL, INSTRUCTION (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (EJ361:E18,TW) 3-249-141-11 MANUAL, INSTRUCTION (ENGLISH, TRADITIONAL CHINESE) (EJ365:HK) 3-249-141-21 MANUAL, INSTRUCTION (ENGLISH, SIMPLIFIED CHINESE) (EJ365:CH,E18) 8-954-008-90 RECEIVER, EAR MDR-E808SP (EJ365) 8-954-008-93 RECEIVER,EAR MDR-E808LP(EJ361,EJ361SR) 8-988-044-90 SPEAKER SYSTEM SRS-A5 (EJ361SR)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
21
D-EJ361/EJ361SR/EJ365
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2003.03 New Description of Revision