Text preview for : DSC-H2 ver.1.2 L2.pdf part of SONY DSC-H2 level 2,3 S.M.
Back to : SONY DSC-H2 level 2,3.pa | Home
DSC-H2
SERVICE MANUAL
Ver. 1.2 2006. 10
Revision History How to use Acrobat Reader LEVEL
2
Internal memory ON BOARD
US Model Canadian Model AEP Model UK Model E Model Australian Model Chinese Model Argentina Model Hong Kong Model Korea Model Tourist Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· Precaution on Replacing the SY-150 board
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DIGITAL STILL CAMERA
DSC-H2_L2
9-876-937-31
Sony EMCS Co.
2006J1600-1 ©2006.10 Published by Kohda TEC
These specifications are extracted from instruction manual of DSC-H2 (2-673-166-11).
SPECIFICATIONS
Camera
[System]
Image device 7.18 mm (1/2.5 type) color CCD, Primary color filter
[LCD screen]
LCD panel 5.1 cm (2.0 type) TFT drive Total number of dots 84 960 (35424 0) dots
BC-CS2A/CS2B Ni-MH battery charger
Power requirements AC 100 to 240 V, 50/60 Hz, 3W Output voltage 0.5 cm (0.2 type) color AA: DC 1.4V 400 mA × 2 AAA: DC 1.4 V 160 mA × 2
Total pixel number of camera Approx. 6 183 000 pixels Effective pixel number of camera Approx. 6 003 000 pixels Lens Carl Zeiss Vario-Tessar 12× zoom lens f = 6.0 72.0 mm (36 432 mm when converted to a 35 mm still camera) F2.8 3.7
[Finder]
Panel Total number of dots Approx. 200 000 dots equivalent
Operating temperature 0 to +40°C (+32 to +104°F) Storage temperature 20 to +60°C (4 to +140°F) Dimensions Approx. 713091 mm (2 7/8×1 3/16×3 5/8 inches) (W/H/D) Approx. 90 g (3 oz)
[Power, general]
Power HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2), 2.4 V R6 (size AA) alkaline batteries (2), 3 V ZR6 (size AA) Oxy Nickel Primary Battery (2), 3 V AC-LS5K AC Adaptor 4.2 V Power consumption (during shooting with the LCD screen) 1.1 W Operating temperature 0 to 40°C (32 to 104°F) Storage temperature 20 to +60°C (4 to +140°F) Dimensions 113.28 3.094.0 mm (4 1/2 inches×3 3/8 inches× 3 3/4 inches) (W/H/D, excluding protrusions) Approx. 537 g (1 lb 2.9 oz) (including two batterries, shoulder strap, adaptor ring, lens hood, lens cap, etc.) Electret condenser microphone Dynamic speaker Compatible
Mass
Exposure control Automatic exposure, Shutter speed priority, Aperture priority, Manual exposure, Scene Selection (7 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash, One push
Design and specifications are subject to change without notice.
File format (DCF compliant) Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media Internal Memory (30 MB) "Memory Stick Duo" Flash Recommended distance (ISO set to Auto): approx. 0.3 m to 9.0 m (11 7/8 inches to 29 feet 6 3/8 inches) (W)/approx. 0.9 m to 6.8 m (35 1/2 inches to 22 feet 3 3/4 inches) (T) Electric viewfinder (color)
Mass
Viewfinder
Microphone Speaker Exif Print
[Input and Output connectors]
A/V OUT jack (Monaural) Minijack Video: 1 Vp-p, 75 , unbalanced, sync negative Audio: 327 mV (at a 47 k load) Output impedance 2.2 k USB jack mini-B
PRINT Image Matching III Compatible PictBridge Compatible
USB communication Hi-Speed USB (USB 2.0 compliant)
DSC-H2_L2
--2--
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
DSC-H2_L2
--3--
TABLE OF CONTENTS 1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY ······ 1-1 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY ·················································· 1-2 1-3. PRECAUTION ON REPLACING THE SY-150 BOARD ··········································································· 1-3 1-4. VIDEO OUT DEFAULT DATA CHECK ······················· 1-3 1-5. INITIAL LANGUAGE DATA CHECK ·························· 1-3
2.
DISASSEMBLY
2-1. DISASSEMBLY ······························································ 2-3
3.
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM ···································· 3-1 3-2. POWER BLOCK DIAGRAM ········································· 3-5
4.
4-1. 4-2. 4-3. 4-4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
FRAME SCHEMATIC DIAGRAM ································ 4-1 SCHEMATIC DIAGRAMS ············································ 4-5 PRINTED WIRING BOARDS ····································· 4-43 MOUNTED PARTS LOCATION ································· 4-56
5.
REPAIR PARTS LIST
5-1. EXPLODED VIEWS ······················································ 5-3 5-2. ELECTRICAL PARTS LIST ········································ 5-10
DSC-H2_L2
--4--
1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display · C: ss: ss The contents which can be handled by customer, are displayed. · E: ss: ss The contents which can be handled by engineer, are displayed.
Display Code C:32:01
Countermeasure Turn off the main power then back on. Replace the memory stick. Format the memory stick with the DSC-H2. Checking of flash unit or replacement of flash unit.
Cause Trouble with hardware. · The type of memory stick that cannot be used by this machine, is inserted. · Data is damaged. · Unformatted memory stick is inserted. Abnormality when flash is being charged.
Caution Display During Error SYSTEM ERROR
C:13:01
MS ERROR Flash LED Flash display Flashing at 3.2 Hz --
E:91:01 E:61:00 *1
Checking of lens drive circuit E:61:10 *1 E:62:10 *1 E:62:11 *1 Inspect angular velocity sensor peripheral circuits.
When failed in the focus initialization.
Steady shot function does not work well.
--
Note : The error code is cleared if the battery is removed, except defective flash unit. *1: The error display is given in two ways.
DSC-H2_L2 1-1
1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: 1 When replacing the SY-150 board, erase the data in internal memory of the board before replacement. Note: 2 When replacing the SY-150 board or the IC202 on the SY-150 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a "Memory Stick".
OK Cancel
See the following procedure. Cancels the copying.
1 Insert a "Memory Stick" having 32 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be copied Ready?" appears. 3 Select [OK] with v , then press z. Copying starts.
Copying 102_COPY
Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files using batteries with little remaining capacity, the batteries may run out, causing copying to fail or possibly corrupting the data. You cannot copy individual images. The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick" after copying, then execute the [Format] command in Internal Memory Tool. You cannot select a folder copied on a "Memory Stick". The setting of (Print order) marks is not copied even when you copy data.
Method for Formatting the Internal Memory
Format
Formats the internal memory.
Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK Cancel
See the following procedure. Cancels the formatting.
1 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be erased Ready?" appears. 2 Select [OK] with v, then press z. The format is complete.
· PROCESS AFTER FIXING FLASH ERROR
When "FLASH error" (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK Cancel
See the following procedure. Cancels the resetting.
1 Select [OK] with v on the control button, then press z. The message "Initialize all settings Ready?" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting.
Make sure that the power is not disconnected during resetting.
DSC-H2_L2 1-2
1-3. PRECAUTION ON REPLACING THE SY-150 BOARD
· The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not required. · Perform "VIDEO OUT Default Data Check" and "Initial Language Data Check" mentioned below, and also the adjustment items necessary after SY Board replacement.
1-4. VIDEO OUT DEFAULT DATA CHECK
When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcast system (NTSC/PAL). When the data has changed because of board replaceing etc., check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value. VIDEO OUT Default Data Page 4F Address 8D Data NTSC 00 PAL 01
Writing Method: 1) Select page: 00, address: 01, and set data: 01. 2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL). 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is "00". 6) Select page: 80, address: 30, and check that the data is "00". 7) Select page: 00, address: 01, and set data: 00.
1-5. INITIAL LANGUAGE DATA CHECK
If the SY-150 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial language as that of the set distributing in each region. Initial language: Language displayed at the next starting if the setting of Setup menu was reset. It is different from the language setting selectable with the menu. Initial Language Data Page Address Data 00 04 4F 8C 08 0B 0D Language English Spanish Simplified Chinese Russian Korean z z GP2 z GP3 z z GP4 z z z
Note: GP2 is fixed to English. GP3 is either English, Spanish, or Russian. GP4 is either English, Spanish, Simplified Chinese, or Korean. Writing Method: 1) Select page: 00, address: 01, and set data: 01. 2) Select page: 4F, address: 8C, and set the Initial Language Data. 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is "00". 6) Select page: 80, address: 30, and check that the data is "00". 7) Select page: 00, address: 01, and set data: 00. 8) Turn off the camera. 9) Turn on the camera. Execute "Initialize" of Setup screen. 10) Check the language displayed when the camera starts.
DSC-H2_L2 1-3E
2. DISASSEMBLY
Link
DISASSEMBLY HELP
COMMON NOTE FOR DISASSEMBLY
DSC-H2_L2
2. DISASSEMBLY
2. DISASSEMBLY
NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire.
Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside)
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR
The charging elect capacitor 320uF (330V) is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-H2 is simply turned off. Therefore, the remaining voltage must be discharged as described below.
Discharging the Capacitor
Short circuits between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds.
Short jig (1k/1W)
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a resistor of 1 kW /1 W (1-215-869-11) Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
ST-142 board
1 k/1 W
Capacitor
Wrap insulating tape.
ST-142
DSC-H2_L2 2-1
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2. DISASSEMBLY
2-1. DISASSEMBLY
2 8
SW 3 47
7
SW 73 4
6 1 4 2 5
3 1 1 Three screws (M1.7x4) 2 Three screws (M1.7x4) 3 Cabinet (rear) section 1 Claw 2 Claw 3 Remove the LCD unit in the 3 5 Flexible board (from the LCD unit) 6 Two tapping screws (M1.7x4) 7 SW-478 flexible board 8 SW-473 board
direction of the arrow.
4 Flexible board (from the LCD unit)
Note: Be very careful not to
damage the flexible board.
9
7 8 1
A (See page 2-5)
-15 0
5 2 4 6
SY
B (See page 2-5)
0
3
2 1 Fuse replacement caution label 3 2 Flexible board (from the lens section) 3 Tape (CD) retainer 1 Two claws 2 Two tapping screws (M1.7x4) 3 LCD frame 4 CD-621 flexible board 5 AF-105 flexible board 6 Flexible board (from the lens section) 7 Control switch block 8 Flexible flat cable (ST-003) 9 From the microphone q; Tapping screw (M1.7x4) qa Main section qa
SY
-15
59 66
34 1 q; HELP 01 q;
7 8
SY-150
2 1 6
DSC-H2_L2 2-3 2-4
2. DISASSEMBLY
4 1 2 3 3 6
2
1
Refer to page 2-1 "DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR, when discharging the capacitor.
1
2
7 8
4 5 9
HELP 04
3
HELP 07
HELP 05
HELP 06
1
A
2 HELP 08
1 Turn the flexible board. 2 Tapping screw (M1.7x5) 3 Lens section
1 Two tapping screws (M1.7x4) 2 Control switch block
1 Tapping screw (M1.7x4) 2 Microphone holder 3 Microphone cushion (B) 4 Microphone 5 Microphone cushion 6 Tapping screw (M1.7x4) 7 AF-105 flexible board 8 Tapping screw (M1.7x4) 9 AF holder
1 Claw 2 Three harnesses (HA-001) (Red, White, Blue) 3 Open the ST cover in the direction of the arrow. 4 ST section
B
3 1 5 5 4 HELP 03 6 3 3 2 1 1 6 2
SY
5 -1
0
HELP 02 2
SY
15
0
1 Flexible flat cable (MS-030) 7 1 Two claws 2 Flexible board (from the LCD module) 3 EVF section 1 Battery connector 2 From the loudspeaker 3 JK-306 flexible board 4 Two tapping screws (M1.7x4) 2 Two tapping screws (M1.7x4) 4 5 Flexible flat cable (MS-030) 6 SW-478 flexible board 7 SY-150 board 3 MS-307 board 4 Battery connector 5 Three claws 6 Battery terminal board
DSC-H2_L2 2-5 2-6E
HELP
Disassembling and assembling procedures that require attention are described here.
HELP 01
When attaching the fuse replacement caution label to the SY-150 board, cover the harness of the loudspeaker with the fuse replacement caution label.
Fuse replacement caution label
Harnesses of the loudspeaker
HELP 02
When installing the loudspeaker, route the harnesses of the loudspeaker as shown in the figure.
Harnesses of the loudspeaker Loudspeaker (1.0cm)
Bend the harness of the loudspeaker at the route of the connector.
HELP 03
When installing the battery terminal board, route the harnesses of the battery terminal board as shown in the figure. The harness in the area A must be kept below surface B.
Battery terminal board surface B Harnesses of the battery terminal board D A C
The harness in the area C must be kept within the D lines.
Harnesses of the battery terminal board
DSC-H2_L2
HELP
HELP 04
HELP 05
When installing the ST section, route the Harness (HA-004) (Blue) ,Harness (HA-004)(White), and Harness (HA-004) (Red) as shown in the figure.
When installing the ST section, route the Harness (HA-004) (Blue) ,Harness (HA-004)(White), and Harness (HA-004) (Red) as shown in the figure.
Route the harnesses with the ST cover closed.
ST section
Harness (HA-004) (Blue) , Harness (HA-004)(White), Harness (HA-004) (Red) ST section
Harness (HA-004) (Blue)
Harness (HA-004) (White) Harness (HA-004) (Red)
HELP 06 4 1 Harness (H-004) (Red) 5 9 2 Harness (H-004) (White) 3 Harness (H-004) (Blue) 4 Flash unit, ST-144 board q; 5 Apply the soldering in three points. 6 ST-142 board 7 Apply the soldering in three points. 8 ST cover 9 Two claws 2White 3Blue 1Red 8 9 Tapping screw (M1.7x4)
Solder each lead according to the color ( Red, White, Blue) as shown in the figure.
6
Solder each lead according to the color ( Red, White, Blue) as shown in the figure.
ST-144 board
ST-142 board
Blue Red White
7
Blue White
Red
DSC-H2_L2
HELP
HELP 07
Install the microphone tilted as shown in the figure below.
Microphone holder Microphone cushion (B)
Microphone holder Microphone cushion (B) Microphone Microphone cushion
Microphone Microphone cushion
HELP 08
When removing the lens ring, remove the screw and strap sheet metal (R) first. Slide the cap lever in the direction of arrow A while taking care that the cap lever is not caught on the notch of the lens ring. Remove the lens ring by turning it in the direction of arrow B.
Cap lever
1 Tapping screw (M1.7x4) 2 Strap sheet metal (R)
B
Cap lever Lens ring
A
3 Lens ring
Notch of the lens ring
DSC-H2_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (2/2)
DSC-H2_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS UNIT
IRIS SHUTER
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CD-621 FLEXIBLE BOARD MS-030 FLEXIBLE FLAT CABLE
K5,G4,H4,L5 H2,H1,J1,J2 M5,J4,K4,M6 K2,K1 AC4,AE4 AE5,AC5 AB6,AF6 CN301 4,3,5, 7,2,8 6 4,3,5,7,2,8 CN302 MEMORY STICK Duo CONNECTOR
CD-619 BOARD
SY-150 BOARD (1/2)
22 | 35 MS D0-MS D3, MS BS, MS CLK XMS IN 6 CN706
IC002
CCD IMAGER 15 1
V1A,B V2 V3A,B V4 V5A,B V6 V7A,B V8, VST, VHLD
CA AD0 - CA AD13 X101
12MHz XTAL OSC
4,3,5, 7,2,8
IC001
BUFFER
CCD OUT 3 20 20 6
S/H A/D CONV.
(3/8)
EXTAL A6
6
(2/8)
12 10 8 6 14 CN001 12 10 8 6 14 CN301
1-14
27,28 19-17 H1A,B H2A,B RG 1 | 5
CP301
TIMING GENERATOR 47 45 46 CLK TGO E1 H5 J5 CA HD, CA FD
IC101 (1/2)
CAMERA DSP
D21,D22,D20,B22,A22,A23 B23,E20,E21,B24,A24,A25 B25,C25,C26,B26,E10,A10 D10,E11,B10,A11,B11,E12 D11,D12,F12,B12,A12,E13 D13,D14 D17,D18,D16,B18,A19 B19,E16,D19,E19,E17 B20,A20 D8,D7,E8 E7,D6,D5 E6,B4
MS-307 BOARD
CN001 26-39
D0-D31
(4/8)
26-39 CN301
7 | 20
42
XSAN_RST_OUT
X102
33.75MHz XTAL OSC
IC203
A0-A11 256Mbit SDRAM CN702 10 LCD D2-D7 | 15 22 21 18 25 24 28 24 | 19 12 13 16 9 10 6
CLKTGEXT
IRIS MOTOR
M
SHUTTER MOTOR
1 4
IRIS A IRIS XA IRIS B IRIS XB
(1/8)
F2 E2 D2 B1 F3 F4 D6 E6 B7 C6
IC401
(1/2)
IRIS DRIVE SHUTTER DRIVE
SAN1 SO,SCK
F5 E5 D3 F1 G1 E4 D5 A6 B6 C5
DIR2A BRK2A DIR2B BRK2B
C1
SW-473 BOARD (1/2)
CN401 LCD D2-D7 CN403 19 | 24 26 27 25 29 28 31 Including the BACK LIGHT LCD D0-D7 LCD9001 2.0 INCH COLOR LCD PANEL
40, 41 DIR2A BRK2A DIR2B BRK2B
M
FOCUS MOTOR
8 5
SHUTTER + SHUTTERFOCUS A FOCUS XA FOCUS B FOCUS XB
MSHUT DIR MSHUT EN
N4 P6 P4 R2 R25 R5 L2 N5 L4 N6 N2 U4
E9 B8 D9
LCD HD LCD VD LCD CK
M
ZOOM MOTOR
9 16
FOCUS MOTOR DRIVE
FC DIR A FC DIR B FC EN
MSHUT DIR MSHUT EN FC DIR A FC DIR B FC EN ZM DIR A ZM BRK A FC SENS ZM SENS 1ST ZM SENS 2ND
U2 SAN1 SO, SCK R6 AF4 XSAN RST OUT
SAN1 SO, SCK
M
FOCUS RESET SENSOR ZOOM RESET SENSOR 1ST ZOOM RESET SENSOR 2ND ZOOM DC FG
36 39
ZOOM + ZOOM -
B4 B5
ZOOM MOTOR DRIVE
A2 B2
ZM DIR A ZM BRK A
SW-478 FLEXIBLE BOARD (1/2)
CN703 15 | 12 LCD D0-D7 10 | 7 LCD HD LCD VD 18 17 LCD CK 19 SAN1 SO, SCK XMS IN XSAN RST OUT 6 4 20
22
FC SENS ZM DC FG 1A ZM DC FG 1B LENS TEMP
U5 V4 V5 W4 J25
24
ZM SENS 1ST
LCD9002 COLOR EVF UNIT
25 32 31 18
ZM SENS 2ND ZM DC FG 1A ZM DC FG 1B LENS TEMP CN401 B4 B5 A2
with in BACK LIGHT
LENS TEMP SENSOR
(4/8)
(4/8)
IC201
ACTIVE LENS ACTUATOR PITCH 11 10 7 6 12 13 3 2 BURST FLASH MEMORY PITCH + PITCH PITCH HALL+ PITCH HALLYAW+ YAW-
IC202
ONE NAND FLASH MEMORY L26 AUIN
(5/8)
SAN1 SO, SCK F3 E3 E6
IC602
MIC AMP B6 A5 A2 SPEAKER AMP
CN602 2 1 2 CN601
MIC SIG SP+ SP-
MIC
MIC9001
B1 D1 H2 J4 B10 D10 J9 J7
A7
XSAN RST OUT D0-D15
A01-A21 D0-D15
A01-A16 C1 AUOUT
SP9001 SPEAKER
H
YAW
(6/8)
D0-D15
AB13,AA13,AE13,AF13,AF12 AE12,AA12,AC12,AC11,AB12 AE11,AF11,AE10,AB11,AC10 AB10 AF21,AF20,AE20,AB18,AB19 AC19,AB16,AE19,AF19,AF18 AE18,AA15,AC18,AC17,AB15 AE17,AF17,AE16,AB14,AC16 AC15 SAN27M CK0 XBONOBO CPU RESET AF9 AC25 V OUT H26
K26
E5 AU OUT AMP
D1 C2 CN651 3,2
IC504
STEADY SHOT CONTROL
A01-A21
H
YAW HALL+ YAW HALL-
AC1 AD1 USB VBUS XAV JACK IN
USB DPP, USB DMM
9 8
CN001 (USB)
CN501
A3 A6
SAN 27M CLK0 XBONOBO CPU RESET
6 1
A4 B4
SE501
SAN0 SO, SI, SCK
B5
(6/8)
PITCH SENSOR
SE502
8
IC506
PITCH/YAW SENSOR AMP
2
PITCH AD
G5
B6
KEY BONO XMS IN USB V BUS
TO OVERALL BLOCK DIAGRAM (2/2)
1
U25
1
AU LINE OUT
J001 A/V OUT
3 SAN1 SO, SCK 3
(PAGE 3-3)
(5/8)
YAW SENSOR
12
18
YAW AD
J5
IC601
VIDEO AMP
5
V LINE OUT 2
V LINE OUT
JK-306 FLEXIBLE BOARD
DSC-H2_L2 3-1 3-2
3-2. OVERALL BLOCK DIAGRAM (2/2)
SY-150 BOARD (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
ST-003 FLEXIBLE FLAT CABLE
(3/8)
1 | 3 1 | 3
ST-142 BOARD
ST-144 BOARD
ST UNREG T101 15 D102 (RECT) XE H
IC101 (2/2)
SYSTEM CONTROL
STRB CHG R22 XSTRB FULL V23 STRB CHG CONT AB22
7 6 5
STRB CHG XSTRB FULL STRB CHG CONT
7 6 5
10 9 6
HIGH VOLTAGE CHAGER
1 2
C105
L001 TRIGGER COIL FLASH UNIT
IC101
IGBT DRIVE 7
Q101 FLASH DRIVE XE L D001
STRB ON R4 CN701
4
STRB ON
4 CN101
4
1
TO OVERALL BLOCK DIAGRAM (1/2)
SAN0 SO, SI, SCK KEY BONO
USB VBUS XMS IN
(1/8)
(PAGE 3-1)
STRB PLUNGER ON AA25
A1
IC401 (2/2)
STRB PLUNGER DRIVE
CN705 B3 8 7
AF-105 FLEXIBLE BOARD
STRB PLUNGER 3 4 4 3
RY201 PLUNGER
XSTRB POPUP V22 XLENS COVER SENSE AC23
5 1 XAF LED
XSTRB_POPUP
1 6 CN201
S201 (FLASH POP UP)
S001 (LENS COVER OPEN)
4 BT9001
BATTERY TERMINAL
D001 (AF LED)
PL-045 BOARD
1 2 3 4
UNREG REG GND F001
ST UNREG
CN704 CN001 SAN0 SO C5 SAN0 SI C6 XSAN0 SCK B6
BATT SENS D4 XDD RST OUT
A7 B7
S103
9 6
SAN0 SO, SI, SCK
AB5 AA5 Y5 K25 Y4 R26 AA23
SAN0 SO SAN0 SI XSAN0 SCK BATT SENS XDD RST OUT XPWR OFF
XAE LOCK SW XSHUTTER SW MODE DIAL 0 MODE DIAL 1
N21 P23
SHUTTER
CONTROL SWITCH BLOCK
S105
L22 L25 AB23 W22 G25
14 12 11 10
MODE DIAL
(8/8)
UNREG F002
XPWR OFF
JOG A JOG B
JOG DIAL S106,101,102 EXEC
IC001
DC/DC CONVERTER REAL TIME CLOCK
A8
OSC I OSC O
X001 32.768KHz
A9 B8
EVER SRAM D 3.2V CAM 3.2V A 3.2V MS VCC CAM 2.9V PANEL 2.9V D 1.8V M 5V ST 5V D 1.2V CAM 15V CAM -7.5V BL H BL L A4 XAF LED
KEY AD2
8
FINDER/LCD, FOCUS, BRK S108
XPLAY SW
1 XPWR LED D23 5
PLAY D102 (POWER) S104
3
XPWR ON
POWER S107
VL 3V
BT001 LITHIUM BATTERY (SECONDARY)
2
KEY BONO
STEADY SHOT
C7 C9
XPWR ON USB VBUS
B10 XMS IN
CN702 KEY AD0 K23 8 26
S507, 510, 505, 503, 506, 509 DOWN, RIGHT, UP, LEFT, SET, DUST S504, 508, 501, 502
Including in the LCD unit (LCD9001) LCD BACK LIGHT 1 2 5 6 CN401 CN402
D7
XPLAY SW
KEY AD1 L23
7
27
ZOOM WIDE, ZOOM TELE, MENU, DISPLAY
XACCESS LED E4
1 30 31 32 33 BL H BL L
33 4 3 2 1
D503 (ACCESS)
SW-478 FLEXIBLE BOARD (2/2)
SW-473 BOARD (2/2)
DSC-H2_L2 3-3 3-4
3-3. POWER BLOCK DIAGRAM (1/2)
SY-150 BOARD (1/2)
BT9001
BATTERY TERMINAL
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
ST-003 FLEXIBLE FLAT CABLE
ST UNREG ST UNREG
ST-142 BOARD
T101 1 | 3 7 6 5 8 CN101
15
1 2
UNREG
F001
1 | 3 7 6 5 8
D102(RECT)
XE H
FLASH UNIT
STRB CHG 3 REG GND 4 CN001 XSTRB FULL STRB CHG CONT
L101
10 9 6
IC101
HIGH VOLTAGE CHAGER IGBT DRIVE
1 2
C105
ST 5V
CN701
F002
3
ST-144 BOARD
MS VCC
UNREG
ST UNREG
(5/8) (8/8)
AU 3.0V PWR1-1 A1 PWR1-2 B1 PWR1-3 C2 VO1-1 F1 VO1-2 F2 VFB1 H2 MS PWR IN MS PWR LDO3IN 2.9V REG LDO3
K25 Y4 R26 AA23 T25
AU 3.0V ST 5V CAM 3.2V D 3.2V A 3.2V
MS-307 BOARD
CN302 MEMORY STICK Duo CONNECTOR 9 CN301 MS VCC 10 10 CN706
R002
IC001
DC/DC CONVERTER REAL TIME CLOCK J1 UNREG1-1,2 K1 EVER SRAM
D001
ST 5V CAM 3.2V D 3.2V L001 L011 A 3.2V
IC602
MIC AMP SPEAKER AMP AU OUT AMP
H1
LDO1
3.1V REG.
G1
(5/8)
4 1
VL 3V
MS-030 FLEXIBLE FLAT CABLE
BT001 LITHIUM BATTERY (SECONDARY)
B8 RTC BAT
A8 OSC I
MS VCC
G2
IC603
3
AU 3.0V
3V REG
STRB CHG XSTRB FULL STRB CHG CONT
R22 V23 AB22
X001 32.768KHz
B2
(3/8)
A9 OSC O
CAM 2.9V
A2
CAM 2.9V
IC101
CAMERA DSP SYSTEM CONTROL
BATT SENS XDD RST OUT XPWR OFF MS PWR ON
D4 DTG1 A7 XRESET B7 XPWR OFF MS PWR ON D3
LDO2IN 1.8V REG LDO2
PANEL 2.9V
B3
D 1.8V
A3
UNREG2
CONTROL SWITCH BLOCK
XCS DD SAN0 SO SAN0 SI XSAN0 SCK
W23 AB5 AA5 Y5
XCS DD C5 SAN0 SO C6 SAN0 SI B6 XSAN0 SCK
A6
J6 K6
PWR56 OUT J7 K7 LX5-1 LX5-2 LX5-3 LX5-4
J9 J10 K9 K10
L006 CAM 15V D003 (RECT) Q004 SWITCHING & RECT CAM -7.5V
D102 (POWER)
5
D23
XPWR LED
VFB5 H9
D 3.2V 4 D 3.2V A 3.2V AU 3.0V VI 3.2V D 1.2V 13 D 1.8V SD 1.8V
TO POWER BLOCK DIAGRAM (2/2)
1
GT6 H6 VFB6 H7
L009 M 5V
(PAGE 3-7)
PWR2
D10
L003 LX2 C10 VFB2 D8
C7 XPWRON1
F003
MODE DIAL
A 3.2V
D 1.2V ST UNREG L005
S104 POWER S108 PLAY XPLAY SW
1 CN704 D 3.2V
XPWR ON
XPWR ON
3
XPLAY SW
LX3
D7 XPWRON2
E10
BL H D002 (RECT) BL L
BL H
L201
VO3 E9
(4/8)
LV3 RS3
F9 F8
BL L
IC203
(4/8)
256Mbit SDRAM
L008 Q001 SWITCHING BG4 G9
Q003 SWITCH M 5V ST 5V ST 5V PANEL 8.5V ON
IC202
ONE NAND FLASH MEMORY
(4/8)
AF-105 FLEXIBLE BOARD
D3.2V 3
D 1.8V
IC201
BURST FLASH MEMORY
A4
TG4
F10
VFB4 F7 PSG4 G8
XAF LED
Q002 RECT
MT 5V ON PANEL 2.9V
D001 (AF LED)
XAF LED
4 CN705
PORTB C4 PORTA B4
PANEL 8.5V ON MT 5V ON CAM 3.2V VI 3.2V D601 L602
(5/8)
IC601
VIDEO AMP
D 3.2V A 3.2V, AU 3.0V, VI 3.2V, D 1.8V, D 1.2V
DSC-H2_L2 3-5 3-6
3-4. POWER BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-150 BOARD (2/2)
CAM 3.2V D 3.2V A 3.2V CAM 2.9V ST 5V
4 1
L303 L302
FB308
HDVDD TG 3V DRVDD FE 3V TCVDD RGVDD
(2/8)
(2/8)
L304
CP301
S/H A/D CONV. TIMING GENERATOR
CD-621 FLEXIBLE BOARD
CD-619 BOARD
IC001
BUFFER
IC301
3
3.3V REG
FB302 FB301
CAM 15V CAM -7.5V
L301
CAM 15V CD CAM -7.5V CD CN301
22 18 22 18
IC002
CCD IMAGER CN001
D 3.2V
D 3.2V
(1/8)
A 3.2V M 5V
21
FC RST VCC
IC401
IRIS DRIVE SHUTTER DRIVE FOCUS MOTOR DRIVE ZOOM MOTOR DRIVE PLUNGER DRIVE
27 28
FOCUS RESET SENSOR
LENS UNIT
ZM RST VCC
ZOOM RESET SENSOR
ZM FG VCC
33
(6/8)
L503
C542 D501 (RECT)
ZOOM DC FG
CN401 PANEL 8.5V
4
IC507
6
8.5V REG
9 SW D502 (RECT) 1
PANEL 8.5V 0N
1
TO POWER BLOCK DIAGRAM (1/2)
ST UNREG Q504 ST 5V M 5V ON
6 8
VBAT PS
(6/8)
VOUT 2
5V
IC501
DC/DC CONV.
(6/8)
1
EN
IC506
PITCH/YAW SENSOR AMP 2.9V
3
SE501, 502
PITCH/YAW SENSOR
(PAGE 3-6)
(6/8)
A 3.2V
4
IC503
2.9V REG
SW-478 FLEXIBLE BOARD
4
SW-473 BOARD
30
L403 L402
PANEL 8.5V
VDD2 VDD1D D503 CN403
14 15
LCD9001 2.0 INCH COLOR LCD PANEL
D 3.2V
6
D 3.2V
28
ACCESS LED
BL H BL L CN702
30 31 32 33
BL H BL L
4 3 2 1 CN401
1 2 5 6
CN402
LCD BACK LIGHT
(6/8)
D3.2V ST 5V
4 1
(6/8)
IC505
3
IC504
1.5V STEADY SHOT CONTROL
1.5V REG
PANEL 8.5V 0N M 5V ON PANEL 2.9V L701
4 1
(7/8)
IC701
3
2.5V
22
2.5V REG 5.0V L702
1
LCD9002 COLOR EVF UNIT
ST 5V
LED 5V CN703
11
EVF BACK LIGHT
DSC-H2_L2 3-7 3-8E
I
J E F
L
H
M
P B A D N 1
K
C
O
G
DSC-H2_L2
2
LCD UNIT
33 32 31 30 29 28 27 26 25 24 23 22 14 21 13 20 12 19 18 17 16 15 14 13 12 11 10 2 9 1 CN651 14P XAV_JACK_IN 8 7 6 5 CN401 39P
1 2 10 11 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7 8 9
VCOMI VSS XRST XCS SI XSCK VSYNC HSYNC MCK DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 RSVD RSVD VDD1A VDD1D VDD2 VSSA VSS2C1 VSS2C2 VSS2OUT VSS2IN CSI VCOMO TEST1 TEST2
3
STATIC_GND STATIC_GND NC GND GND D+ DGND VCC NC GND AU_LINE_OUT V_LINE_OUT
4
11 10 9 8 7 6 5 4 3
CN403 33P
EVF UNIT
4-1. FRAME SCHEMATIC DIAGRAM
JK-306 FLEXIBLE BOARD
SPEAKER
4 3 2 1 TEST3 VSS TEST NC
CN703
AV/USB JACK
1
SP_SP_+
5
IRIS_XB IRIS_A
NC SEN 5.0V 2.5V GND GND SDAT SCLK VALID DATA7 DATA6 DATA5 DATA3 DATA2 DATA1 DATA0 LED5V CLOCK DARA4 VSYNC HSYNC NRESET
6
CN601
2 3
22P
4-1
IRIS_B
2P
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 ZM_DC_MOTOR_ZM_DC_MOTOR_ZM_DC_MOTOR_+ ZM_DC_MOTOR_+ XZM_FG_TR XZM_FG_LED ZM_FG_VCC ZM_DC_FG_1A ZM_DC_FG_1B XZM_RST_TR2 XZM_RST_LED2 ZM_RST_VCC2 ZM_RST_VCC1 XZM_RST_LED1 ZM_SENS_2ND ZM_SENS_1ST XZM_RST_TR1 FC_SENS FC_RST_VCC XFC_RST_TR XFC_RST_LED LENS_TMP REG_GND FOCUS_XA FOCUS_XA FOCUS_B CN702 33P XACCESS_LED REG_GND REG_GND PANEL_8.5V REG_GND D_3.2V KEY_AD1 KEY_AD0 REG_GND LCD_D3 LCD_D2 LCD_D5 LCD_D4 LCD_D7 LCD_D6 REG_GND REG_GND LCD_CK REG_GND REG_GND LCD_VD LCD_HD REG_GND XSAN1_SCK SAN1_SO REG_GND XCS_PNAEL FOCUS_B FOCUS_A FOCUS_A FOCUS_XB FOCUS_XB SHUTTER_+ SHUTTER_+ SHUTTER_SHUTTER_-
IRIS_XA
7
SW-473 BOARD
(1/2) LCD PANEL (2/2) FUNCTION SWITCH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 XSAN_RST_OUT NC BL_H BL_H BL_L BL_L 28 29 30 31 32 33
33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
XACCESS_LED REG_GND REG_GND PANEL_8.5V REG_GND D_3.2V KEY_AD1 KEY_AD0 REG_GND
8
LENS UNIT
6
5
4
3
2
1
LCD_D3
NC NC BL_L BL_L BL_H BL_H
9
LCD_D2 LCD_D5 LCD_D4 LCD_D7 LCD_D6 REG_GND REG_GND
CN401 33P
CN402 6P
SW-478 FLEXIBLE BOARD
SY-SW RELAY
10
LCD_CK REG_GND REG_GND LCD_VD LCD_HD REG_GND XSAN1_SCK SAN1_SO
SY-150 BOARD
11
REG_GND XCS_PNAEL XSAN_RST_OUT NC BL_H BL_H BL_L BL_L
CN001 CN301 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 H2A REG_GND RAMDOM_TRIGGER REG_GND CSUB VSUB 6 5 4 3 2 1 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 19 20 21 REG_GND CCD_OUT REG_GND CAM_-7.5V_CD REG_GND REG_GND REG_GND RG REG_GND H1A REG_GND H1B 22 CAM_15V_CD 23 REG_GND 24 REG_GND 25 REG_GND 26 V5A 27 V1A 28 V5B 29 V1B 30 VHLD 31 V2 32 V6 33 V3A 34 V7A 35 V3B 36 V7B 37 VST 38 V8 39 V4 39P V4 V8 VST V7B V3B V7A V3A V6 V2 VHLD V1B V5B V1A V5A REG_GND REG_GND REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND CAM_-7.5V_CD REG_GND REG_GND REG_GND RG REG_GND H1A REG_GND H1B REG_GND H2B REG_GND
39P
12
MIC
(1/8) LENS DRIVE (2/8) CAMERA A/D CONV.TIMING GENERATOR (3/8) CAMERA DSP,SYSTEM CONTROL (4/8) 256Mbit SDRAM,FLASH MEMORY,One NAND (5/8) A/V AMP,A/V,USB JACK RELAY (6/8) STEADY SHOT CONTROL (7/8) CONNECTOR (8/8) DC/DC CONVERTER
13
SY-CD RELAY
PLUNGER
PL-045 BOARD
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
CD-621 FLEXIBLE BOARD
CD-619 BOARD
REG_GND H2B REG_GND H2A REG_GND RAMDOM_TRIGGER REG_GND CSUB VSUB 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NC YAWYAW+ PITCH+ PITCHREG_GND PITCH_HALLBAISPITCH_HALL+ PITCH_HALLPITCH_HALLBAIS+ YAW_HALLBAISYAW_HALL+ YAW_HALLYAW_HALLBAIS+ CN501 14P
CCD IMAGER
CN201 CN602 2P MIC_SIG MIC_GND 2 1 6 5 4 3 2 1 1 2 3 4 5 6 REG_GND REG_GND
6P
14
STRB_PLUNGER STRB_PLUNGER REG_GND XSTRB_POPUP
CN705
10P REG_GND REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND XSTRB_POPUP XAF_LED D_3.2V REG_GND XLENS_COVER_SENSE 10 9 8 7 6 5 4 3 2 1
15
AF-105 FLEXIBLE BOARD
AF LED,LENS COVER SW
16
CN001 4P REG_GND REG_GND UNREG UNREG 4
17
3 2 1
CN704 14P
XAE_LOCK_SW
XSHUTTER_SW
CN701 12@
CN706
18
JOG_A JOG_B
KEY_BONO
MODE_DIAL0
MODE_DIAL1
XPLAY_SW
KEY_AD2
XPWR_LED D_3.2V
A_3.2V
REG_GND
STRB_CHG_CONT
XSTRB_FULL
STRB_CHG
ST_UNREG 1
ST_UNREG ST_UNREG 2 3
REG_GND
REG_GND
REG_GND
REG_GND
XPWR_ON
STRB_ON 4
MS_VCC
XMS_IN
REG_GND
REG_GND
MS_CLK
ST_5V
12P
MS_D1 MS_BS
MS_D0
MS_D3
MS_D2
REG_GND 11
REG_GND 12
10
10
11
12
10
11
12
13
14
5
6
7
8
1
2
3
4
5
6
7
8
9
9
1
2
3
4
5
6
7
8
9
4-2
1 ST_UNREG
ST-003 FLEXIBLE FLAT CABLE
SY-ST RELAY
10 11 12 2 ST_UNREG 3 ST_UNREG 4 STRB_ON 5 STRB_CHG_CONT 6 XSTRB_FULL 7 STRB_CHG 8 ST_5V 9 REG_GND 1 2
MS-030 FLEXIBLE FLAT CABLE
SY-MS RELAY
10 11 12 3 4 5 6 7 8 9 CN301
19
BATTERY
BATTERY
CN101
MS_D1
MS_D0
MS_D2
MS_D3
MS_BS
XMS_IN
MS_VCC
MS_SCLK
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
12P
12P
20
ST-142 BOARD
FLASH DRIVE
REG_GND XE_L 3 2 XE_H 1
21
MS-307 BOARD
MEMORY STICK
6 9 MS_VCC REG_GND 7 8 10 MS_D3 XMS_IN MS_SCLK 1 4 5 MS_D2 MS_D0 3 MS_D1 2 MS_BS CN302 10P REG_GND
22
CONTROL SWITCH BLOCK(MODE DIAL)
MODE/JOG DIAL,FUNCTION SW
23
ST-144 BOARD
FLASH
MEMORY STICK Duo CONNECTOR
24
FRAME SCHEMATIC DIAGRAM
4-2. SCHEMATIC DIAGRAMS
Link
CD-619 BOARD (CCD IMAGER) SW-473 BOARD (1/2) (LCD PANEL) SW-473 BOARD (2/2) (FUNCTION SWITCH) ST-142 BOARD (FLASH DRIVE) ST-144 BOARD (FLASH) MS-307 BOARD (MEMORY STICK) PL-045 BOARD (PLUNGER) CONTROL SWITCH BLOCK
(MODE/JOG DIAL, FUNCTION SW)
AF-105 FLEXIBLE BOARD
(AF LED, LENS COVER SW)
JK-306 FLEXIBLE BOARD (AV/USB JACK) CD-621 FLEXIBLE BOARD (SY-CD RELAY) SW-478 FLEXIBLE BOARD (SY-SW RELAY) MS-030 FLEXIBLE FLAT CABLE (SY-MS RELAY) ST-003 FLEXIBLE FLAT CABLE (SY-ST RELAY)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-H2_L2
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ Link V or less are not indicated except for electrolytics µF. 50 and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor Temperature characteristics External dimensions (mm) · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with * differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B Line · J : IN/OUT direction of (+,) B LINE. · C: adjustment for repair. (Measuring conditions voltage) · Voltages are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.) 1. Connection
Pattern box
Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A
Color bar chart
For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = 1 m (PTB-450) L = 40 cm (PTB-1450) Pattern box L Front of the lens Camera
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
Cyan Green White Magenta
A B
A=B
Fig. a (Video output terminal output waveform)
Red Blue
B A
Electronic beam scanning frame CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of imager
· If the imager has been replaced, carry out all the adjustments for the camera section. · As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. When indicating parts by reference number, please include the board name.
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DSC-H2_L2 4-3
4-2. SCHEMATIC DIAGRAMS
1 CD-619 BOARD
CCD IMAGER
XX MARK:NO MOUNT
2
3
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
4
5
6
7
8
9
10
CL006
CN001
39P V4 V8 VST V7B V3B 39 38 37 14 13 12 11 10 36 9 8 7 6 5
VHLD
V8
V6
V4
VST
V7B
V7A
V5B
V5A
V3B
V3A
V2
V1B
35 34 33 32 CCD IMAGER
B
V7A V3A V6 V2 VHLD V1B V5B TO CD-621 FLEXIBLE BOARD V1A V5A REG_GND REG_GND REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND
IC002
VDD H1B H2B RG
IC002 ICX624BQF-13
CSUB
GND
GND
GND
SUB
N.C.
30 29 28
H1A 16V B
15 16 17 18 19 20 21 22 23 24 25 26 27 28 27 26 25 24 23 22 21 20 19 18 R9.1 P0 C002 0.01u 16V C004 0.1u 16V
C
IC001
BUFFER
C005 0.1u 16V
(PAGE 4-19)
1
IN VCC GND OUT IDRV IC001 CXA3691EN-T9
6
ISF
FB001 0uH
REG_GND REG_GND RG REG_GND H1A REG_GND
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 2 R002 0 0 3 1 R8.1 P0 Q001 DTC144EMT2L VSUB R003 270k R004 1M C001 XX
R007 220k C008 XX
C003 XX R009 1200
C006
E
H1B REG_GND H2B REG_GND H2A REG_GND RAMDOM_TRIGGER REG_GND
F
CSUB VSUB
DSC-H2_L2 4-5 4-6
C007
0.1u
3
4
R9.1 P0
R3.6 P0
0.1u
REG_GND
17
16V B
D
CAM_-7.5V_CD
2
5
R12.1 P0
R-7.5 P0 R2.1 P0.1 R1.2 P0.1
R6.6 P0 R2.1 P0.1 R1.2 P0.1 R2.4 P0
R8.3 P-0.2 R8.7 P0
9.1
12.1
H2A
VL
Note: IC002 is not included in this COMPLETE of CD-619 board.
CCD_OUT
31
V1A
R-6.3 P0 R-6.2 P0 R-6.2 P0 R-0.4 P0 R-7.2 P0 R-0.4 P0 R-0.4 P0 R-0.4 P0 R-5.8 P0 R-0.4 P0 R-0.4 P0 R-0.4 P0 R-0.5 P0 R-0.5 P0
4 3 2 1
CL007
A
CD-619
1
2
3
4
5
6
7
CN402 6 5 4 3 2
8
6P
9
SW-473 BOARD(1/2) A
LCD PANEL
XX MARK:NO MOUNT
BL_L BL_L NC NC BL_H BL_H LCD BACK LIGHT
CN401 33P BL_L BL_L BL_H 1 2
1
33 3 32 BL_H NC XSANN_RST_OUT XCS_PNAEL REG_GND SAN1_SO XSAN1_SCK REG_GND 4 31 5 30 6 29 7 28 8 27 9 26 10 25 11 24 LCD_HD LCD_VD TO SW-478 FLEXIBLE BOARD REG_GND REG_GND LCD_CK REG_GND REG_GND LCD_D6 12 23 13 22 14 21 15 20 16 17 18 18 17 19 16 LCD_D7 LCD_D4 LCD_D5 LCD_D2 LCD_D3 REG_GND KEY_AD0 KEY_AD1 20 21 14 22 23 24 25 26 27 28 29 6 PANEL_8.5V REG_GND REG_GND XACCESS_LED 30 31 32 33 C402 10u 6.3V P L403 10uH C405 2.2u C 5 4 3 2 1 REG_GND L402 10uH C408 10u 10 9 C406 4.7u 8 7 REG_GND C409 JL402 R405 47k C410 XX 0.22u 13 12 11 JL401 15 JL403 19
VCOMI VSS XRST XCS SI XSCK VSYNC HSYNC MCK DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 RSVD RSVD VDD1A VDD1D VDD2 VSSA VSS2C1 VSS2C2 VSS2OUT VSS2IN CSI VCOMO TEST1 TEST2 TEST3 VSS TEST NC 2.0 INCH COLOR LCD PANEL
B
C
(PAGE 4-20)
D
E
D_3.2V
C401 XX
F
D_3.2V
CN403 33P
@01
(2/2)
KEY_AD0 KEY_AD1 XACCESS_LED
LCD9001 (LCD UNIT)
DSC-H2_L2 4-7 4-8
SW-473(1/2)
1
2
3
4
5
6
7
8
SW-473 BOARD(2/2) A
FUNCTION SWITCH
XX MARK:NO MOUNT
8 6 4 2
S504 ZOOM W
S508 ZOOM T
RB501 2200 x 4
7 5 3 1
R501 5600
S501 MENU 2 1
2 NO 3 6
1 4 5
2 NO 3 6
1 4 5
B
4
3 S502 S505 UP 1 2 1
7 5 3 1
KEY_AD1 KEY_AD0
R502 27k 2
DISP
C
4
3
4
3
8 6 4 2 D502 MAZW068H0LS0
R505
330 D_3.2V
@01
(1/2)
RB502 2200 x 4 R503 5600 2 S503 1 S506 SET 4 1 3 4 2 R504 27k 4 3 3 S510 RIGHT 2 1 D501 1SS387-TPL3
D503 SML-310LTT86 XACCESS_LED
3
1
2
(ACCESS)
D
LEFT
REG_GND
2
1
S507 DOWN
4
3 2 1
S509 DUST
E
4
3 LND501 STATIC_GND
DSC-H2_L2 4-9 4-10
SW-473(2/2)
· Refer to page 4-3 for mark 0.
1
2 ST-142 BOARD
FLASH DRIVE
XX MARK:NO MOUNT
CN101 12P ST_UNREG ST_UNREG ST_UNREG 1 2 3 4 5 6 7 8 9 10 11 12
3
4
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
5
6
7
8
9
10
A
T101 CONVERTER TRANSFORMER
L101 4.7uH C101 22u 6.3V C102 22u 6.3V C106 22u 6.3V CL101
5 2 1
3 D102 CRF02(TE85R) 4
LND101 1 XE_H
B
TO ST-003 FLEXIBLE FLAT CABLE
STRB_ON STRB_CHG_CONT XSTRB_FULL STRB_CHG ST_5V REG_GND REG_GND REG_GND REG_GND
(PAGE 4-22)
C105 320u 330V
Note: C105 is not included in this COMPLETE of ST-142 board.
C
HGND VBATT N.C
R2.4/P2.6 17 16 15 14 13
TO ST-144 BOARD
(PAGE 4-13)
N.C
R2.4/P2.6
SW SW VCC F_ON
4
IC101 TPS65552RGTR
D101 MAZS068008SO
N.C
N.C
R102 XX
C103 1u B
G_IGBT
I_PEAK
9
D
5.0
2
PGND CHG XFULL
10 11 12
R2.4/P2.6
N.C
IC101
HIGH VOLTAGE CHARGE, IGBT DRIVE
1
PGND
0 3.2
LND102 2 REG_GND
0
3
Q101 GT8G133 (T2LSONY.Q) FLASH DRIVE 283 LND103 3 XE_L 1 2 0 R103 4.7M C104 XX R104 33 3 4 5 6 7 8
5
6
7
8
0
E
F
DSC-H2_L2 4-11 4-12
0
ST-142
Ver. 1.1 2006. 06
· Refer to page 4-3 for mark 0.
1
FLASH
2 ST-144 BOARD
3
4
5
6
1
2 PL-045 BOARD
3
4
A
XX MARK:NO MOUNT
A
LND001 LND005 XE_+
PLUNGER
XX MARK:NO MOUNT
CN201 6P 1 2 3 4 5 6 S201 (FLASH POP UP) C201 1u 1 2 RY201 (PLUNGER) D202 1SS355TE-17 D203 MAZW068H0LS0
REG_GND TO AF-105 FLEXIBLE BOARD REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND XSTRB_POPUP
XE_H
1
R001 1M
3
B
TO ST-142 BOARD
C002 0.047u 250V
L001 TRIGGER COIL 1 3 LND004 TRIGGER FLASH UNIT
B
(PAGE 4-17)
(PAGE 4-12)
LND002 XE_L 2
C003 0.01u 250V
2
LND006 XE_D001 RR255L-400TE25 R002 100k
NOTE: RY201 is not included in this COMPLETE of PL-045 board.
C
LND003 REG_GND 3
1 MS-307 BOARD A
MEMORY STICK
XX MARK:NO MOUNT
2
3
4
5
6
CN301 12P REG_GND MS_BS MS_D1 1 2 3 4 5 6 FB304 MS_D3 MS_SCLK REG_GND MS_VCC REG_GND 7 8 9 10 11 12 C301 22u 6.3V C302 0.1u B R304 82 0uH 7 8 9 10 MS_D3 R306 0 R302 1k R303 82 R305 0 FB301 FB302 FB303 0uH 0uH 0uH 1 2 3 4 5 6
10P REG_GND MS_BS MS_D1 MS_D0 MS_D2 XMS_IN CN302 MEMORY STICK Duo CONNECTOR
B
TO MS-030 FLEXIBLE FLAT CABLE
MS_D0 MS_D2 XMS_IN
(PAGE 4-21)
MS_SCLK MS_VCC REG_GND
C
REG_GND
LND302
STATIC_GND
DSC-H2_L2 4-13 4-14
ST-144/MS-307/PL-045
1
2
3
4
5
6
7
8
CONTROL SWITCH BLOCK A
MODE/JOG DIAL, FUNCTION SW
XX MARK:NO MOUNT
(MODE DIAL) S101 FOCUS 2 1 S102 BRK 2 1 3 R104 2k R105 2k R106 2k R107 2k 5 4 3 2 1 8 6 7 13 12 11 10 9 R117 2k R118 2k R115 2k R116 2k R109 2k R111 2k R112 2k S107 S106 FINDER 2 4 1 3 2 1 STEADY SHOT
4
3
4
3
4
B
R101 4900
R110 2k R108 10k R103 2200
R114 2k
C
R102 9300
S103 SHUTTER S105 3 4 1 2 S104 POWER 3 1 JOG DIAL
7
1
2
3
4
5
2
4
D
S108 PLAY 1 3 D102 2 4 POWER
E
LND101 LND102 LND103 LND104 LND105 LND106 LND107 LND108 LND109 LND110 LND111 LND112 LND113 LND114
CONTROL SWITCH BLOCK is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
XSHUTTER_SW
MODE_DIAL1
XPLAY_SW
14P
10
11
12
13
TO SY-150 BOARD(7/8) CN704
G
(PAGE 4-35 of LEVEL 3)
DSC-H2_L2 4-15 4-16
14
1
2
3
4
5
6
7
8
9
MODE_DIAL0
XPWR_LED
KEY_BONO
XPWR_ON
REG_GND
KEY_AD2
F
XAE_LOCK_SW
D_3.2V
A_3.2V
JOG_B
JOG_A
6
MODE DIAL
Ver. 1.1 2006. 06
1
2
3
4
5
6
AF-105 FLEXIBLE BOARD A
AF LED,LENS COVER SW
XX MARK:NO MOUNT
S001 (LENS COVER OPEN) 10P 1 2 3 TO SY-150 BOARD (7/8) CN705 4 5 6 7 8 9 10 XLENS_COVER_SENSE LND002 REG_GND LND003 D_3.2V LND004 XAF_LED LND005 XSTRB_POPUP LND006 REG_GND LND007 STRB_PLUNGER LND008 STRB_PLUNGER LND009 REG_GND LND010 REG_GND LND016 REG_GND 6 LND015 REG_GND 5 LND014 STRB_PLUNGER 4 LND013 STRB_PLUNGER 3 LND012 REG_GND 2 LND011 XSTRB_POPUP 6P 1 TO PL-045 BOARD CN201 LND001 1 2 3 D001 DOR5073 (AF LED) 6 5 4
B
(PAGE 4-35 of LEVEL 3)
(PAGE 4-14)
C
NOTE: D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.
1
2
3
4
5
6
JK-306 FLEXIBLE BOARD A
AV/USB JACK
XX MARK:NO MOUNT
14P XAV_JACK_IN V_LINE_OUT AU_LINE_OUT GND 1 LND002 2 LND003 3 LND004 4 LND005 5 LND006 VCC GND DD+ GND GND NC 6 LND007 7 LND008 8 LND009 9 LND010 10 LND011 11 LND012 12 LND013 13 LND014 STATIC_GND 14 LND015 STATIC_GND STATIC_GND 1 VCC 2 D3 D+ (USB) 4 ID 5 GND CN001 5P NC LND001 3 1 2 4 J001 A/V OUT
B
TO SY-150 BOARD (5/8) CN651
(PAGE 4-32 of LEVEL 3)
C
DSC-H2_L2 4-17 4-18
AF-105/JK-306
1
2
3
4
5
1
2
3
4
5
A
CD-621 FLEXIBLE BOARD
SY-CD RELAY
XX MARK:NO MOUNT
39P V4 V8 VST V7B 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 39P
SW-478 FLEXIBLE BOARD A
39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 V4
BL_L 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 BL_L BL_H BL_H NC XSAN_RST_OUT XCS_PANEL REG_GND SAN1_SO XSAN1_SCK REG_GND LCD_HD LCD_VD REG_GND REG_GND LCD_CK REG_GND REG_GND LCD_D6 LCD_D7 LCD_D4 LCD_D5 LCD_D2 LCD_D3 REG_GND KEY_AD0 KEY_AD1 D_3.2V REG_GND PANEL_8.5V REG_GND REG_GND XACCESS_LED TO SW-473 BOARD(1/2) CN401
SY-SW RELAY
XX MARK:NO MOUNT
33P BL_L 33 1 33P BL_L
V8
BL_H
VST
BL_H
V7B V3B V7A
XCS_PANEL
B
V3B V7A V3A V6 V2 VHLD V1B V5B
B
NC XSAN_RST_OUT
V3A
REG_GND
V6
SAN1_SO
V2
XSAN1_SCK
VHLD
REG_GND
V1B
LCD_HD
V5B V1A V5A REG_GND REG_GND
C
V1A V5A REG_GND REG_GND TO SY-150 BOARD(2/8) CN301 REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND CAM_-7.5V_CD REG_GND REG_GND REG_GND RG REG_GND H1A
C
TO SY-150 BOARD(7/8) CN702
LCD_VD REG_GND REG_GND LCD_CK REG_GND
(PAGE 4-36 of LEVEL 3)
TO CD-619 BOARD CN001
(PAGE 4-7)
REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND CAM_-7.5V_CD
REG_GND LCD_D6 LCD_D7
D
(PAGE 4-25 of LEVEL 3)
(PAGE 4-5)
D
LCD_D4 LCD_D5 LCD_D2
REG_GND
LCD_D3
REG_GND
REG_GND
REG_GND
KEY_AD0
RG
KEY_AD1
REG_GND
D_3.2V
H1A REG_GND H1B
REG_GND
E
REG_GND H1B REG_GND H2B REG_GND H2A REG_GND RANDOM_TRIGGER
E
REG_GND PANEL_8.5V
REG_GND
REG_GND
H2B
XACCESS_LED
REG_GND H2A REG_GND RANDOM_TRIGGER REG_GND CSUB VSUB
F
REG_GND CSUB VSUB
DSC-H2_L2 4-19 4-20
CD-621/SW-478
1
2
SY-MS RELAY
XX MARK:NO MOUNT
12P REG_GND MS_BS MS_D1 MS_D0 1 2 3 4 5 6 7 8 9 10 11 12
3
4
5
1
2
SY-ST RELAY
XX MARK:NO MOUNT
12P
3
4
5
MS-030 FLEXIBLE FLAT CABLE A A
12P 1 2 3 4 5 6 7 8 9 10 11 12 REG_GND MS_BS MS_D1 MS_D0 MS_D2 XMS_IN MS_D3 MS_SCLK REG_GND MS_VCC REG_GND REG_GND TO MS-307 BOARD CN301
ST-003 FLEXIBLE FLAT CABLE
12P 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 REG_GND REG_GND REG_GND REG_GND ST_5V STRB_CHG XSTRB_FULL STRB_CHG_CONT STRB_ON ST_UNREG ST_UNREG ST_UNREG TO ST-142 BOARD CN101
REG_GND REG_GND REG_GND REG_GND
B
TO SY-150 BOARD(7/8) CN706
MS_D2 XMS_IN MS_D3 MS_SCLK REG_GND MS_VCC REG_GND REG_GND
B
TO SY-150 BOARD(7/8) CN701
ST_5V STRB_CHG XSTRB_FULL STRB_CHG_CONT STRB_ON ST_UNREG ST_UNREG ST_UNREG
(PAGE 4-35 of LEVEL 3)
(PAGE 4-13)
(PAGE 4-35 of LEVEL 3)
(PAGE 4-11)
C
MS-030 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
C
ST-003 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
Schematic diagram of the SY-150 board and CH-169 board are not shown. Pages from 4-23 to 4-40 are not shown.
DSC-H2_L2 4-21 4-22
MS-030/ST-003
4-3. PRINTED WIRING BOARDS
Link
CD-619 BOARD SW-473 BOARD ST-142 BOARD ST-144 BOARD MS-307 BOARD PL-045 BOARD AF-105 FLEXIBLE BOARD JK-306 FLEXIBLE BOARD CD-621 FLEXIBLE BOARD SW-478 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
DSC-H2_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block)
(For printed wiring boards) · : Uses unleaded solder. · : Pattern from the side which enables seeing. (The other layers' patterns are not indicated) · Through hole is omitted. · There are a few cases that the part printed on diagram isn't mounted in this model. · C: panel designation
· Chip parts. Transistor
C
6 5 4 4 5 6 5
4 4
5
Diode
3
3
3
1 23
B
E
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 4
2 1
1 2 2 3
1 2 4 4
1 6 54 3 3 4
5 4 3 3 4 5 2
1
4 5
3 2 4
6
1 1 2 4 3
2
1
1
3 1
3
1
2
DSC-H2_L2 4-41
4-3. PRINTED WIRING BOARDS
CD-619 (4 layers) · : Uses unleaded solder.
CD-619 BOARD(SIDE A)
CD-619 BOARD(SIDE B)
Note:IC002 is not included in this COMPLETE of CD-619 board
A
28 15
A
C005
C003 C004
IC001
3
IC002
FB001
R009 C008
1
C007
B
1 14
2 1
C002
4 R007
6
R003 R004 C001
R002
1-869-220C006
B
38
1 2 3
11
Q001
CL007 CL006
CN001
39
1-869-220-
11
1
2
3
1
2
3
DSC-H2_L2 4-43 4-44
CD-619
SW-473 (4 layers), ST-142 (2 layers)
·
: Uses unleaded solder.
SW-473 BOARD(SIDE A)
1
SW-473 BOARD(SIDE B)
RB502 R503 2
S501 MENU C401
1
2
1
S502 DISP
7
2
A
A
R504 S510 RIGHT
3
4
3
4
8
5
B
1
S508 6 T 3
D501 1
2
4 2 4
LND501
2
D502
1
3
A K D503 ACCESS
R505
3
ZOOM SW-473
>EP GW< 1-869-219
C402 L403 C405
L402
S505 UP
S506 SET
S507 DOWN
B
2 1
3
4
3
4
3
4
CN401
32 33 R502
2 8 RB501 1 7
1
2
1
2
1
R405
3
4
3 6 4
W 1 S504
5 2
S503 LEFT C409 C406 2 1
1 2
3 4 S509 DUST
2
R501
JL402 JL401
JL403
1
C408
C410
2
+ P
C 1 2
32 CN403 33
1
6
1-869-219-
C
11
CN402
1-869-219- 11
3
4
4
3
2
1
ST-142 BOARD(SIDE A)
L101
ST-142 BOARD(SIDE B)
3 2
C101
C102
A
LND101 LND103 LND102
5
T101
C103 CL101
1
1 4 R103
Q101
5
R104 5 4
8 9
1 17
16 13
C106 R102 A K
4
12
IC101
D102
1 C105
8
D101 C104
B
ST-142 1-869-218-
1
12
CN101
1-869-218-
11
2
1
2
3
4
4
3
2
DSC-H2_L2 4-45 4-46
ST142-
>EP GW<
A
B
1-869-218-
11
1
SW-473/ST-142
Ver. 1.1 2006. 06
ST-144 (1 layer), MS-307 (4 layers), PL-045 (2 layers) · : Uses unleaded solder.
ST-144 BOARD
D001
C002
LND002 C003 LND003 R002 LND001 R001
ST144 >PI<
PL-045 BOARD (SIDE A)
PL-045 BOARD (SIDE B)
1 6
-11
CN201
2 3
S201 1 2 RY201
(FLASH POP UP)
1
LND006
1
LND004
11
1-869-217-
11
NOTE: RY201 is not included in this COMPLETE of PL-045 board.
LND302
MS-307 BOARD(SIDE A)
MS-307 BOARD(SIDE B)
11
CN301
MS-307 >EP 1-869-221R304 R303
12 1
R305 FB301 FB302 FB303 R302 FB304 R306
1
MEMORY STICK Duo CONNECTOR
10
C302
12
1-869-221-
11
DSC-H2_L2 4-47 4-48
+ P
CN302
C301
1-869-22111
PL045
3
1-869-225-
(PLUNGER)
2
2
LND005 L001
1
D203
C201
>EP GW<
D202
1-869-217-
11
GW<
ST-144/MS-307/PL-045
Ver. 1.1 2006. 06
AF-105 FLEXIBLE (1 layer), JK-306 FLEXIBLE (1 layer), CD-621 FLEXIBLE (2 layers), SW-478 FLEXIBLE (1 layer) · : Uses unleaded solder.
AF-105 FLEXIBLE BOARD
LND011 LND012 LND013 LND014 LND015 LND016
CD-621 FLEXIBLE BOARD
1 1
1
6
D001 10
K
AF LED
6 4
LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002
39
S001
1-869-222- 39 11
(LENS COVER OPEN)
2 1 3 1
1
3
A
AF-105
1-869-223-
>PI<
1-869-223-
11
SW-478 FLEXIBLE BOARD
33 1
NOTE: D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.
JK-306 FLEXIBLE BOARD
4 2 J001 3 1 A/V OUT
>PI<
>PI<
1 CN001 1 2 (USB) 5 14
FX
JK-3061-869-22411
SY
FX
1-869-227-
SW-478-
Printed wiring board of the SY-150 board and CH-169 board are not shown. Pages from 4-51 to 4-55 are not shown.
11
1 33
DSC-H2_L2 4-49 4-50
AF-105/JK-306/CD-621/SW-478
4-3. PRINTED WIRING BOARDS
4-4. MOUNTED PARTS LOCATION
CD-619 BOARD
* * * * * * * * C001 C002 C003 C004 C005 C006 C007 C008 B-2 B-1 B-1 B-1 B-1 B-2 B-1 B-2 B-2 B-3
no mark : side A * mark : side B ST-142 BOARD
C101 C102 C103 C104 * C105 C106 CL101 A-2 A-2 A-2 B-2 B-3 B-3 A-2
SW-473 BOARD
C401 C402 C405 C406 C408 C409 C410 A-3 B-2 B-2 C-2 C-2 C-2 C-2
* CL006 * CL007
* CN401 B-4 CN402 C-4 CN403 C-3 * D501 * D502 D503 JL401 JL402 JL403 L402 L403 B-4 B-4 B-4 C-3 C-3 C-4 B-2 B-2
CN101 B-3 D101 D102 IC101 L101 B-2 B-3 B-3 A-1
* CN001 B-1 * FB001 * IC001 IC002 * Q001 * * * * * R002 R003 R004 R007 R009 B-1 B-1 B-2 B-2 B-2 B-2 B-2 B-1 B-2
LND101 A-1 LND102 A-2 LND103 A-1 Q101 B-1 B-3 B-2 B-2 A-3
* LND501 B-4 R405 * R501 * R502 R503 R504 * R505 C-2 C-2 C-2 B-3 A-3 B-4 R102 R103 R104 T101
* RB501 C-2 RB502 B-3 S501 S502 S503 S504 S505 S506 S507 S508 S509 S510 A-2 A-2 B-3 C-1 B-2 B-3 B-4 B-1 B-4 B-3
Mounted parts location of the SY-150 board is not shown. Page 4-57 is not shown.
DSC-H2_L2 4-56E
CD-619/SW-473/ST-142
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
F
I G B
D
OVERALL SECTION
CABINET (REAR) SECTION
MAIN SECTION
LENS SECTION
A
H C E
CABINET (FRONT) SECTION
ST SECTION
Link
AF-105 FLEXIBLE BOARD CD-619 BOARD JK-306 FLEXIBLE BOARD
ELECTRICAL PARTS LIST
A D G
ACCESSORIES
C F I
MS-307 BOARD PL-045 BOARD ST-142 BOARD
B E H
ST-144 BOARD SW-473 BOARD SY-150 BOARD
DSC-H2_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Language that can be selected about SY-150 board
Arabic Dutch Russian Swedish Korean Norwegian Danish Finnish Polish Hungarian Czech Persian
z z z z z z z z z z z
Simplified Chinese Traditional Chinese
Portugal
Spanish
German
English
French
Italian
Area
GP2
US CND z z AUS Vietnam AEP UK E AR JE HK CH KR
z z
z
z
GP3
z z z z z z
GP4
z
z
z
z
z
z z
· Abbreviation AR : Argentine model AUS : Australian model CH : Chinese model CND : Canadian model HK : Hong Kong model JE : Tourist model KR : Korea model
DSC-H2_L2 5-1
Thai
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. OVERALL SECTION
Cabinet (front) section
9 (See page 5-7) 1
5 6 7 8 2 3
-15 SY 0
2 10 1
Lens section (See page 5-6)
2
Main section (See page 5-5)
11
4
LCD9001
1
Cabinet (rear) section (See page 5-4)
1
Ref. No. 1 2 3 * 4 5 * 6
Part No. 2-655-582-11 3-080-204-11 2-673-327-01 2-673-307-01 A-1176-910-A
Description SCREW 0+P2 M2 NEWTRU-STAR SCREW, TAPPING, P2 CABINET (UPPER) FRAME, LCD SW-473 BOARD, COMPLETE
Ref. No. 7 8 9 * 10 * 11
Part No. 2-666-551-21 2-673-346-01 2-673-341-01 2-685-307-01 2-673-339-01
Description SCREW, TAPPING, P2 PLATE, ORNAMENTAL EMBLEM (320), ST RETAINER, TAPE (CD) LABEL, FUSE REPLACEMENT CAUTION
2-678-099-01 SHEET, SW MUFFLE
LCD9001 8-753-248-51 ACX351AKM-3
DSC-H2_L2 5-3
5. REPAIR PARTS LIST
5-1-2. CABINET (REAR) SECTION
ns : not supplied
51
53
ns
54 55
52
Ref. No. 51 52 53
Part No.
Description
Ref. No. 54 * 55
Part No.
Description
X-2108-908-1 CABINET (REAR) ASSY 2-673-247-01 LID, DC 2-673-333-01 WINDOW, LCD
2-673-303-01 LID, JK 2-685-484-01 CUSHION (REAR)
DSC-H2_L2 5-4
5. REPAIR PARTS LIST
5-1-3. MAIN SECTION
ns : not supplied
108
LCD9002
110 109
BT9001
101
MS
-30
A
7
111
112 104
BT001 ns
107
A
105 102 106
-1 SY
50
101
103
SP9001
113
ns
101
: BT001 (Lithium battery) SY-150 board on the mount position. (See page 4-52)
Ref. No. 101 102 * 103 104 104 104 105 * 106 107 * 108 Part No. 3-080-204-11 A-1176-915-A 2-672-564-01 A-1176-916-A A-1176-917-A A-1176-918-A 1-869-227-11 2-673-306-01 X-2108-910-1 2-673-337-01 Description SCREW, TAPPING, P2 JK-306 FLEXIBLE BOARD SHEET (JK), RADIATION SY-150 BOARD, COMPLETE (SERVICE) (GP2) SY-150 BOARD, COMPLETE (SERVICE) (GP3) SY-150 BOARD, COMPLETE (SERVICE) (GP4) SW-478 FLEXIBLE BOARD PLATE, JK GROUND HOLDER ASSY, BATTERY RETAINER, MODULE Ref. No. 109 110 111 * 112 * 113 Part No. X-2108-913-1 A-1176-912-A 1-831-557-11 2-677-004-01 2-684-446-01 Description ASSY, VF MS-307 BOARD, COMPLETE FLEXIBLE FLAT CABLE (MS-030) SHEET (INR), RADIATION SPACER, SP BATTERY, LITHIUM SECONDARY TERMINAL BOARD, BATTERY LCD MODULE LOUDSPEAKER (1.0CM)
0 BT001 1-756-539-21 * BT9001 1-780-338-11 LCD9002 1-802-033-11 SP9001 1-826-403-21
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
DSC-H2_L2 5-5
· Refer to page 5-1 for mark 0.
5. REPAIR PARTS LIST
5-1-4. LENS SECTION
ns : not supplied
154
158
159
IC002
151 153 156 155
CD -6 19
152
157 160 157
ns
Ref. No. 151 * 152 153 * 154 155 156
Part No. A-1177-128-A 2-672-563-01 2-592-693-01 2-672-565-01 2-592-605-01
Description OPTICS UNIT (B191A) (SERVICE) SHEET (LNS), RADIATION PLATE (T), LIGHT INTERCEPTION SHEET (TB), RADIATION RUBBER (TM), SEAL
Ref. No. 157 * 158 159 160 IC002
Part No. 2-666-551-21 2-672-562-01 1-869-222-11 A-1176-911-A
Description
1-788-338-11 OPTICAL FILTER BLOCK
SCREW, TAPPING, P2 SHEET (CD), RADIATION CD-621 FLEXIBLE BOARD CD-619 BOARD, COMPLETE (IC002 is not included in this COMPLETE board.) A-1176-034-A CCD BLOCK ASSY (CCD IMAGER) (IC002 is not included in this COMPLETE board of CD-619.)
Be sure to read "Precautions upon replacing CCD imager" on page 4-3 when changing the CCD imager.
DSC-H2_L2 5-6
5. REPAIR PARTS LIST
5-1-5. CABINET (FRONT) SECTION
ns : not supplied
208
ST section (See page 5-8)
209 212 207 210
211 213 202
206 205 202 217 215
ns
214
MIC9001
202
203 218 204 202 201 202 216 202
Ref. No. 201 202 203 * 204 205 206 207 208 209 * 210
Part No. X-2108-906-1 3-080-204-11 2-673-230-01 2-673-328-01 2-673-324-01 2-673-323-01 2-673-325-01 X-2108-325-1 2-673-301-01 2-673-305-01
Description CABINET (FRONT) ASSY SCREW, TAPPING, P2 SCREW, TRIPOD SHEET METAL (R), STRAP RING, ORNAMENTAL RING, LENS GRIP RELEASE ASSY BUTTON, FB PLATE, GRIP GROUND
Ref. No. * 211 212 213 * 214 * 215
Part No. 2-673-302-01 1-831-558-11 1-479-699-11 2-673-335-01 2-673-334-01
Description HOLDER, AF FLEXIBLE FLAT CABLE (ST-003) SWITCH BLOCK, CONTROL CUSHION, MICROPHONE HOLDER, MICROPHONE AF-105 FLEXIBLE BOARD CUSHION (B), MICROPHONE SHEET (LNS), RADIATION MICROPHONE
216 A-1176-913-A * 217 2-678-097-01 * 218 2-672-563-01 MIC9001 1-542-618-21
DSC-H2_L2 5-7
5. REPAIR PARTS LIST
5-1-6. ST SECTION
255 257 254 256
C105
251
Blue
RY201
Red
261
White
260 259 262
258 253
252
251
PRECAUTION DURING SOLENOID PLUNGER INSTALLATION
7 6
5 4 2 3
1
1 Close the ST cover. 2 Plunger solenoid
3 Two claws 4 Solenoid retainer
5 PL-045 board 6 Apply the soldering in two points. 7 Tapping screw (M1.7x4)
Ref. No. 251 252 253 254 0 255 256 257
Part No. 3-080-204-11 A-1176-908-A 2-629-818-01 X-2108-912-1 1-479-553-11
Description SCREW, TAPPING, P2 PL-045 BOARD, COMPLETE RETAINER, SOLENOID BASE ASSY, ST FLASH UNIT
Ref. No. 258 259 260 261 * 262 0 C105 RY201
Part No. 1-964-411-11 1-964-411-21 1-964-411-31 A-1176-909-A 2-678-098-01
Description HARNESS (HA-004) (RED) HARNESS (HA-004) (WHITE) HARNESS (HA-004) (BLUE) ST-142 BOARD, COMPLETE SHEET, ST ELECTROSTATIC
A-1176-914-A ST-144 BOARD, COMPLETE 2-673-326-01 COVER, ST
1-112-763-11 CAP, ELECT 320uF 330V 1-455-038-11 SOLENOID, PLUNGER
DSC-H2_L2 5-8
· Refer to page 5-1 for mark 0.
5. REPAIR PARTS LIST
Checking supplied accessories.
Make sure that the following accessories are supplied with your camcorder.
0 Ni-MH battery charger BC-CS2A/CS2B (1) (US,CND,JE model) 1-479-378-11 0 Ni-MH battery charger BC-CS2A/CS2B (1) (AEP,UK,E,AUS,HK,AR model) 1-479-378-21 0 Ni-MH battery charger BC-CS2A/CS2B (1) (KR,CH model) 1-479-378-31
HR6 (size AA) Nickel-Metal Hydride batteries (2) (not supplied)
Adaptor ring (1) 2-629-861-01
Battery case (1) 3-074-757-01
Lens cap (1) X-2055-960-1
0 Power cord (Mains lead) (1) (US,CND model) 1-790-107-51 0 Power cord (Mains lead) (1) (AEP,E model) 1-824-910-31 0 Power cord (Mains lead) (1) (AUS model) 1-827-945-41 0 Power cord (Mains lead) (1) (KR model) 1-823-947-51 0 Power cord (Mains lead) (1) (UK model) 1-827-269-22 0 Power cord (Mains lead) (1) (HK model) 1-783-374-22 0 Power cord (Mains lead) (1) (AR model) 1-783-952-51 0 Power cord (Mains lead) (1) (CH model) 1-782-476-41 0 Power cord (Mains lead) (1) (JE model) 1-792-549-31
USB cable (1) 1-829-868-41
Lens cap strap (1) 3-979-194-31
AV cable (1) 1-824-519-11
CD-ROM (Cyber-shot application software) (1) 2-666-673-01
Shoulder strap (1) 2-629-892-01
2-pin conversion adaptor (1) (JE model) 1-569-007-12
Lens hood (1) 2-629-860-01
2-pin conversion adaptor (1) (E model) 1-569-008-12
2-673-166-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (US,CND,AEP,UK,E,HK,AUS,JE) 2-673-166-21 INSTRUCTION (USER'S GUIDE) (FRENCH/ITALIAN) (CND,AEP) 2-673-166-31 INSTRUCTION (USER'S GUIDE) (SPANISH/PORTUGUESE)(AEP,E,AR,JE) 2-673-166-41 INSTRUCTION (USER'S GUIDE) (GERMAN/DUTCH)(AEP) 2-673-166-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE/SIMPLIFIED CHINESE)(E,HK,CH,JE) 2-673-166-61 2-673-166-71 2-673-166-81 2-673-166-91 2-673-167-11 INSTRUCTION (USER'S GUIDE) (RUSSIAN)(AEP) INSTRUCTION (USER'S GUIDE) (ARABIC/PERSIAN)(E) INSTRUCTION (USER'S GUIDE) (KOREAN)(KR,JE) INSTRUCTION (USER'S GUIDE) (POLISH/CZECH)(AEP) INSTRUCTION (USER'S GUIDE) (HUNGARIAN/SLOVAK) (AEP)
Other accessories
2-673-164-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US,CND,AEP,UK,E,HK,AUS,JE) 2-673-164-21 INSTRUCTION (READ THIS FIRST) (FRENCH/ITALIAN)(CND,AEP) 2-673-164-31 INSTRUCTION (READ THIS FIRST) (SPANISH/PORTUGUESE)(AEP,E,AR,JE) 2-673-164-41 INSTRUCTION (READ THIS FIRST) (GERMAN/DUTCH) (AEP) 2-673-164-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE/SIMPLIFIED CHINESE)(E,HK,CH,JE) INSTRUCTION (READ THIS FIRST) (RUSSIAN)(AEP) INSTRUCTION (READ THIS FIRST) (ARABIC/PERSIAN)(E) INSTRUCTION (READ THIS FIRST) (KOREAN)(KR,JE) INSTRUCTION (READ THIS FIRST) (CZECH/POLISH) (AEP) 2-673-165-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN/SLOVAK)(AEP) 2-673-165-21 INSTRUCTION (READ THIS FIRST) (SWEDISH/FINNISH) (AEP) 2-673-165-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN/DANISH)(AEP) 2-673-164-61 2-673-164-71 2-673-164-81 2-673-164-91
2-673-167-21 INSTRUCTION (USER'S GUIDE) (SWEDISH/FINNISH) (AEP) 2-673-167-31 INSTRUCTION (USER'S GUIDE) (NORWEGIAN/DANISH) (AEP)
DSC-H2_L2 5-9
· Refer to page 5-1 for mark 0.
Ver. 1.1 2006. 06
AF-105
5-2. ELECTRICAL PARTS LIST
Ref. No. Part No. Description
CD-619
JK-306
Ref. No. Part No.
MS-307
Description
PL-045
ST-142
A-1176-913-A AF-105 FLEXIBLE BOARD, COMPLETE ****************************** (D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.) < DIODE > D001 Not supplied DIODE DOR5073 (AF LED) (D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.) < SWITCH > S001 1-762-805-21 SWITCH, PUSH (1 KEY) (LENS COVER OPEN) ************************************************************ A-1176-911-A CD-619 BOARD, COMPLETE ********************** (IC002 is not included in this COMPLETE board.) < CAPACITOR > C002 C004 C005 C006 C007 1-164-943-81 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < CONNECTOR > * CN001 1-816-057-51 CONNECTOR, FPC (ZIF)