Text preview for : HKTS7-8 sm.pdf part of HARMAN KARDON SUB-TS7 Amplifier Subwofer
Back to : HKTS7-8 sm.pdf | Home
harman/kardon
SUB-TS7(HKTS 7 SUBWOOFER) SUB-TS8(HKTS 8 SUBWOOFER)
SERVICE MANUAL
harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 10/2006
SUB-TS7/TS8
harman/kardon
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . . . . ........................................... . . . 1 DETAILED SPECIFICATIONS . . . . . . . . . . . . . .... . . . . . . . . ....................... 2 CONTROLS & CONNECTIONS............ . . . . . . . . . . . ................... ........... 4 SPEAKER CONNECTIONS.............................................. . . .. . .. . . . . . .. 6 OPERATION....... . . . . .. . . . . . . . .. ........................................................9 BASIC TROUBLESHOOTING GUIDE . . . . . . . . .......................................10 UNIT EXPLODED VIEW. . . . ............... ................ .. ............ . . .. .. .. . ... . 11 AMPLIFIER EXPLODED VIEW. . . . ..................... . .. ............ . . .. . . .. . ... . 12 TEST SET-UP AND PROCEDURE. . . . . . . . ...........................................13 HKTS7 TECH TIP HK2004-04... ...........................................................14 BLOCK DIAGRAM . . . . . . . . . . . . . .. . . . . . . .................. . . . . . . .. . . . . . . 15 PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ......... . ............. . . . . .. .. . . . . . 16 ELECTRICAL PARTS LIST ............. .... . .. . . . . ..................... . . .. .. . . . . 20 SEMICONDUCTOR PINOUTS . . . .. .. .. .. . . . .. . .................................... .24 HKTS7 SCHEMATIC DIAGRAM . . . . . .. .. ..............................................25 HKTS8 SCHEMATIC DIAGRAM . . . . . .. .. .. .. . . . .. . ............................... 28 HKTS7 PACKAGING. .. . . . . . . . . . . . . . .. . . . ................................................. 31 HKTS8 PACKAGING. .. . . . . . . . . . . . . . .. . . . ................................................. 32
SPECIFICATIONS
Amplifier Power (RMS) Driver Inputs 100 Watts 10" woofer, Bass Reflex Enclosure Stereo Line Level, dedicated Subwoofer (LFE) and Speaker Level with gold-plated binding posts Speaker Level with gold-plated binding posts 35Hz 120Hz (Filter switch ON) 35Hz 450Hz (Filter switch OFF) 18-7/8" x 13-3/8" x 13-3/8" 479mm x 340mm x 340mm 33 lb/15kg
Outputs Frequency Response
Dimensions (H x W x D)
Weight
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated.
1
SUB-TS7/TS8
SUB-TS7 100W Powered Sub/ Plate Amp SUB-TS8 100W Powered Sub/ Plate Amp
LINE VOLTAGE US 120vac/60Hz Parameter Amp Section Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power THD @ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity Input Frequency Line (L&R) Input SUB (LFE) Input Speaker/Hi Level Input Hi Level Max. Input Voltage Signal to Noise SNR-A-Weighted SNR-unweighted SNR rel. 1W-unweighted Residual Noise Floor AB 4 100 0.08 0.15 5 >100 n/a Ohms Watts % % mV-DC n/a n/a n/a 75 0.1 0.5 30 30 Yes/No Yes Nonimal Specification Hi/Lo Line 108-132 Unit Nom. 120 QA Test Limits Unit Vrms Conditions
harman/kardon
Notes Normal Operation Notes
Nominal 50 - 250 Hz, 1 input driven, limiter off 22k filter 22k filter @ Speaker Outputs Measured at amplifier board Measured at the speaker at speaker output terminals on the amp board.
50 220 125 2.2 32
Hz mVrms mVrms Vrms Vrms
n/a 154 - 308 87 - 175 1.5 - 3.0 30
Nominal Freq. To Rated Power To Rated Power To Rated Power Nominal Freq., Min. Volume
Single input driven SUB (LFE) input driven only (20 dB below Line In), Single input driven
100 90 65 1.2
dB dB dB mVrms
85 80 60 3.0
relative to rated power relative to rated power relative to 1W Output Volume @max, using RMS reading DMM/VOM (or A/P) Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)
A-Weighting filter 22k filter 22k filter
Residual Noise Floor Input Impedance Line Input (L, R,LFE) Speaker/Hi Level Input Filters L&R Fixed Low-Pass Filter SUB (LFE) Low pass Filter Subsonic filter (HPF) 3rd Order Limiter THD at Max. Output Power Features Auto - On -Off Selection Switch Phase Switch Filter On/Off Switch Volume Pot Taper (Lin/Log) Speaker Out 2-Color LED power indicator Power Switch Fuse Holder Input Configuration Line In (L,R) SUB (LFE) Speaker/Hi Level In
0.8
mVrms
2.0
10K 4.7K
ohms ohms
n/a n/a
Nominal Nominal
170 270 28
Hz Hz Hz
150 - 200 @ -6dB ref. 100Hz 240 - 300 @ -3dB ref. 100Hz 22 - 28 @ -3dB ref. 30Hz
2nd order fixed 2nd order fixed 3rd order fixed
2.0
%
5.0
YES 0-180 YES LOG YES YES YES YES
deg
functional functional functional functional functional functional functional functional
Refer to ATO section
A Taper Binding post connector L&R Blue: On, Amber: Stand-by
YES YES
functional functional
Dual RCA jack RCA jack
YES
functional
Binding post connector L&R
Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level Line & SUB Input ATO Level Speaker in ATO Turn-on time ATO Turn-OFF Time Power on Delay time Transients/Pops ATO Transient Turn-on Transient
YES 50 4.0 40 5 15 3
Hz mV mV ms minutes sec.
functional n/a 2.0 - 6.0 25 - 55
Auto - on selection switch in Auto Auto - on selection switch in Auto Auto - on selection switch in Auto Auto - on selection switch in Auto Amp connected and AC on, then input functional signal applied Time before muting, after signal is 10 - 20 removed
functional AC Power Applied
5 50
mV-peak mV-peak
10 100
@ Speaker Outputs @ Speaker Outputs
AC Line cycled from OFF to ON
2
SUB-TS7/TS8
Parameter Turn-off Transient Efficiency Nonimal Specification 50 Unit mV-peak QA Test Conditions Limits 100 @ Speaker Outputs
harman/kardon
Notes AC Line cycled from ON to OFF
Stand-by Input Power Power Consumption @ rated powe Protection Short Circuit Protection
10 170
Watts Watts
12 200
@ nom. line voltage @ nom. line voltage
Maximum allowable input power under nominal input voltage and frequency, in stand-by mode (HOT or COLD operation). 100 Watts @ 4.0 ohms and nominal line voltage
YES
functional Direct short at output
Thermal Protection DC Offset Protection Primary Fuse Rating USA-Domestic (120V)
YES YES 2.5 Amps
functional functional DC present at Speaker Out leads n/a Type-T or Slo Blo
Amplifier should resume operation after short circuit condition is removed. Any user accessible metal parts should always remain at 65 degree C or less for domestic version or 55 degree C or less for EU version. Relay or crowbar (for driver/fire protection), User-replacable fuse with UL/SEMCO rated holder.
3
SUB-TS7/TS8
harman/kardon
SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
SUBWOOFER LEVEL
¡ TM
FILTER
ON OFF MIN MAX
£ ¢
ON AUTO REVERSE NORMAL SUB R L
R ISK OF ELEC TR IC SH O C K D O NO T OPE N
PHASE
C A U TIO N
§
LINE LEVEL IN
H I G H
L
WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE T 2.5A L/250 VOLT FUSE AVERTISSEMENT: UTILISEZ UN FUSIBLE DE RECHANGE DE MEME TYPE T 2.5A L/250V
¶
L E V E L
R
POWER
AC 120V~60Hz
· ª ,
OUT
IN
IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.
¡ Subwoofer-Level Control TM High-Cut (Low-Pass) Filter Switch £ Music-Sense On/Off Switch ¢ Phase Switch
Line-Level Subwoofer (SUB) Input § Line-Level Full-Range Inputs ¶ Speaker-Level Outputs · Speaker-Level Inputs
ª Master Power Switch , AC Power Cord
¡ Subwoofer-Level Control: Volume may be adjusted using the SubwooferLevel Control. Turn the control clockwise to increase the Subwfr volume, or counterclockwise to decrease it. TM High-Cut (Low-Pass) Filter Switch: Placing switch in the ON position activates circuitry that cuts out all audio input signals above 120Hz. This allows the Subwfr to focus its power on reproducing the lowfrequency portion of the signal, avoiding
inefficiency and distortion. Engage this filter when using the Speaker-Level Inputs ·, or when using the Line-Level Full-Range Inputs §, unless your receiver or processor processes its line-level output using a lowpass filter. The filter has no effect when the SUB Input is used. £ Music-Sense On/Off Switch: When placed in the AUTO position, and when the Master Power Switch ª is turned on, the Subwfr will automatically turn itself on or
place itself in the Standby mode, depending on whether it is receiving an audio signal. When this switch is placed in the ON position, the Subwfr will remain on, whether or not it is receiving an audio signal. An LED located on top of the Subwfr indicates whether the Subwfr is in the ON or STANDBY state when used with the MusicSense On/Off Switch £ in the AUTO position. The LED is lit blue to indicate that the Subwfr is receiving an audio signal
SUB-TS8 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
5
4
SUB-TS7/TS8
harman/kardon
SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
and is turned on, and the LED is lit amber to indicate that no signal is being received and the Subwfr is in Standby mode. When the Music-Sense On/Off Switch £ is in the ON position, the LED will be lit blue, whether or not an audio signal is present. When the Master Power Switch ª is turned off, the LED goes dark, no matter which position the Music-Sense On/Off Switch £ is in. ¢ Phase Switch: This switch determines whether the subwoofer's pistonlike action moves in and out in phase with the main speakers. If the speakers were to play out of phase, the sound waves produced by the subwoofer would be cancelled out, reducing bass response. This phenomenon depends in part on the relative placement of the speakers in the room. In most cases, the Phase Switch ¢ should be left in the NORMAL position. However, it does no harm to experiment with the Phase Switch ¢, and you may leave it in the position that maximizes bass response. Line-Level Subwoofer (SUB) Input: Connect the subwoofer output of a receiver with digital surround sound decoding, such as Dolby* Digital or DTS® to this input. This , input bypasses the Subwfr's internal crossover circuitry, and should only be used with a filtered signal. If your receiver does not have digital decoding, you should use the Line-Level Full-Range Inputs § instead. § Line-Level Full-Range Inputs: Connect the line-level subwoofer output or preamp output(s) of your receiver or amplifier to these inputs. If your receiver does not have a separate subwoofer output, use a Y-adapter (not supplied) to bridge the receiver's preamp output to the main amp input for that channel, and connect the long end of the adapter to the corresponding line-level input on the Subwfr. If your receiver has only a single subwoofer output, you may connect it to either the left or right line-level input on the Subwfr, and no Y-adapter is needed. ¶ Speaker-Level Outputs: If you are using the Speaker-Level Inputs · on the Subwfr, you should connect these bindingpost terminals to the front left and right speakers, remembering to maintain polarity by connecting the (+) terminal on the subwoofer to the (+) terminal on the speaker, and the () terminal on the subwoofer to the () terminal on the speaker. If you are not using the Speaker-Level Inputs ·, then connect your front left and right speakers directly to your receiver or amplifier. See pages 8 for further information on speaker connections. · Speaker-Level Inputs: Connect these binding-post terminals to the main left and right speaker terminals of your receiver or amplifier, if your receiver or amplifier does not have a line-level subwoofer output. Remember to maintain polarity by connecting the (+) terminal on the receiver/amplifier to the (+) terminal on the subwoofer, and the () terminal on the receiver/amplifier to the () terminal on the subwoofer. ª Master Power Switch: Place this switch in the "·" position to power-on the subwoofer. The Subwfr will then be either in the Standby mode or completely on, depending on the position of the MusicSense On/Off Switch £. , AC Power Cord: Make sure to plug this cord into an active, unswitched electrical outlet for proper operation of the Subwfr. The cord should not be plugged into the accessory outlets found on some audio components.
5
SUB-TS7/TS8
harman/kardon
SPEAKER CONNECTIONS
Dolby* Digital or DTS® (or Other Digital Surround Mode) Connection
USE THIS INSTALLATION METHOD FOR DOLBY DIGITAL, DTS OR OTHER DIGITAL SURROUND PROCESSORS: Use the line-level input jack marked SUB for the Low-Frequency Effects channel. Connect this jack to the subwoofer output or LFE output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure you've configured your surround sound processor for "Subwoofer On. The " front left, front right, center and surround speakers should all be set to "Small. " When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front Left SUB/LFE Out Surround Left Center Surround Right
Front Left
Center
Front Right
Subwoofer
LINE LEVEL IN SUB R L
Front Right
Surround Left
Surround Back
Surround Right
Receiver
Surround Back
10
SPEAKER CONNECTIONS
6
SUB-TS7/TS8
harman/kardon
SPEAKER CONNECTIONS
Dolby Pro Logic* (Non-Digital) Line Level
USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR IS EQUIPPED WITH A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Use the supplied RCA-type interconnect cable to connect the line-level subwoofer output on your receiver or amplifier to either the left or right Line-Level Full-Range Input § on the subwoofer. Use both the left and right inputs on the subwoofer if your receiver or processor has both left and right line-level outputs. In that case, you will need to supply a second interconnect cable. If your receiver is equipped with line-level outputs but does not have a separate subwoofer output, use a Y-adapter (not supplied) to bridge the receiver's preamp output to the main amp input for that channel, and connect the long end of the adapter to the corresponding line-level input on the Subwfr. IMPORTANT: Do not use the SUB Input on the subwoofer with Dolby Pro Logic processors. If your receiver/processor has a built-in lowpass-crossover filter for the subwoofer output, you may use the SUB Input to bypass the subwoofer's internal crossover. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround sound processor for "Subwoofer On. The front left, front right, center and " surround speakers should all be set to "Small. " When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front Left
Center
Front Right
8 Subwoofer Line-Level R L
Front Left SUB/LFE Out Surround Left Center
Front Right
Surround Right
Surround Left
Surround Back
Surround Right
Receiver
Surround Back
SPEAKER CONNECTIONS 7
11
SUB-TS7/TS8
harman/kardon
SPEAKER CONNECTIONS
Dolby Pro Logic (Non-Digital) Speaker Level
USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR DOES NOT HAVE A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Connect your receiver or amplifier's front left and right speaker terminals to the left and right Speaker-Level Input · terminals on the Subwfr subwoofer that are marked "High Level In." Connect the left and right Speaker-Level Output ¶ terminals on the Subwfr subwoofer that are marked "High Level Out" to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifier's center and surround speaker terminals to the corresponding terminals on the back of your center and surround speakers. When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Surround Left
Front Left
Center
Front Right
SUB-TS8 Subwoofer
H I G H L E V E L
L
R
Front Left
Center
Front Right
Surround Back
Surround Right
Surround Left
Receiver
Surround Back
Surround Right
12
SPEAKER CONNECTIONS 8
SUB-TS7/TS8
harman/kardon
OPERATION
Move the Master Power Switch ª (marked Power) to the "·" (On) position. The Subwfr subwoofer will automatically turn itself on or go into Standby mode, depending on whether or not a signal is being sent to it by your receiver or surround processor, and provided that the MusicSense On/Off Switch £ is moved down so that it is in the AUTO position. When your receiver or amplifier is off, or is not sending program material to the subwoofer, the subwoofer will be in Standby mode and the LED Indicator on the top of the subwoofer will turn amber. When the subwoofer senses an audio signal, it will automatically turn itself on and the LED Indicator will turn blue. If the subwoofer does not sense a signal after approximately twenty minutes, it will automatically go into Standby mode. When the Music-Sense On/Off Switch £ is switched to the ON position, the subwoofer will remain on, whether or not program material is playing, and the LED Indicator will remain lit blue. If you'll be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power Switch ª to the OFF position. Volume Volume can be adjusted using the Subwoofer-Level Control ¡, as shown. Turn the control knob clockwise to increase the volume of the subwoofer, and counterclockwise to decrease the subwoofer's volume.
Subwoofer Level
Additional Bass Adjustments In addition to the volume adjustments described above, the Subwfr subwoofer includes a Phase Switch ¢ and a Filter Switch TM that can be used to adjust the bass response to suit your listening environment or taste. In most situations, the Phase Switch ¢ should be left in the NORMAL position. If you suspect that the subwoofer is playing out of phase with the other speakers, which would tend to diminish bass response, try placing this switch in the REVERSE position. There is no harm in experimenting, and you may return the switch to the NORMAL position at any time. If you rearrange your room and reposition the speakers, it would be a good idea to check whether they are in phase by flipping this switch. The High-Cut (Low-Pass) Filter Switch TM limits the frequencies of the audio signal inputted to the subwoofer to the low frequencies that the subwoofer reproduces best. This allows the subwoofer to perform more efficiently, and with superior bass reproduction, minimizing distortion that might occur if the subwoofer attempted to reproduce higher frequencies. This switch should be left in the ON position, except: 1. When the SUB Input is being used, in which case it has no effect, or 2. When the Speaker-Level Inputs · or the Line-Level Full-Range Inputs § are being used with a crossover or filter aboard the receiver or processor. In these two circumstances, place the switch in the OFF position.
MIN
MAX
Subwoofer Level
MIN
MAX
OPERATION 9
13
SUB-TS7/TS8
harman/kardon
TROUBLESHOOTING
SYMPTOM
If there is no sound from any of the speakers:
SOLUTION
· Check that receiver/amplifier is on and a source is playing. · Check that the powered subwoofer is plugged in and its Master Power Switch ª is switched on to the "·" position. · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured, or touching other wires. · Review proper operation of your receiver/amplifier.
If there is no sound coming · Check the "Balance" control on your receiver/amplifier. from one speaker: · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, and that no wires are touching each other. · In Dolby Digital or DTS mode, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place: i.e., the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved: i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www.harmankardon.com for further information. If there is no sound from the center speaker: · Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, ccut, punctured, or touching other wires. · If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. · If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled. · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured, or touching other wires. · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.
If the system plays at low volumes but shuts off as volume is increased:
If there is low (or no) bass · Make sure the SUB ¡ or Line-Level Inputs § of the subwoofer and SUB or LFE output of your receiver output: or amplifier are properly connected by the RCA-type interconnect cable. · If you are using the Subwfr's Speaker-Level Inputs ·, check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut, punctured, or touching other wires; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals. · Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch ª is switched on to the "·" position. · Check the speaker setup (bass management) settings in your A/V receiver or processor to make certain that the front, center and surround speakers are configured for "Small," and that the subwoofer is set for "Yes" or "On." If there is no sound from the surround speakers: · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured, or touching other wires. · Review proper operation of your receiver/processor and its surround sound features. · Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use. · In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. · Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD player's menu and the DVD disc's menu.
14
TROUBLESHOOTING
10
SUB-TS7/TS8
harman/kardon
Ref# 1 2 3 4 5 6 7 8 9 10 11
Description Amplifier screw SUB-TS7/TS8 Amplifier Port Tube SUB-TS7/TS8 Cabinet Logo LED Grille Logo 10" woofer Woofer screw Foot Pad
Part Number 352-AM04020D210 Not for Sale Not for Sale Not for Sale 316-AG-00557 Not for Sale Not for Sale 316-AL-00553 25PF12DZB-DW01 352-FM04020D605 320-EVA-00057
Qty 10 1 1 1 1 1 1 1 1 5 4
11
SUB-TS7/TS8
harman/kardon
(See Mechanical Parts List on Pages 21-22)
12
SUB-TS7/TS8
harman/kardon
Test Set Up and Procedure
Equipment needed: · Function/signal generator/sweep generator · Integrated Amplifier · Multimeter · Speaker cables Initial Control Settings: · Power Switch OFF; Filter OFF · Level MIN (Full CCW) · Phase, Auto/On switches do not matter General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single, purple SUB input. 2) Turn on generator; adjust to 75mV, 50 Hz. 3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX) 4) LED should turn from Amber to Blue (on top of UUT); immediate and vigorous bass response should be heard and felt from port tube opening. 5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 7) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise. 8) LED should turn from Amber to Blue; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 6-8 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.0 ohms ±10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
13
SUB-TS7/TS8
harman/kardon
harman/kardon
For models: HKTS7 SUB (SUB-TS7)
TECH TIPS
TIP# HKTT2004-04
Troubleshooting tips and solutions to common service problems
Subject: Improved filter performance Instructions: Change four 1/6W ±5% CF Resistors in the PREAMP PCB of the HKTS 7 subwoofer amplifier. It is recommended this procedure be followed for every unit that has to be serviced, for any reason.
Designator R223 R224 R226 R227
Original value 51k 51k 27k 27k
New value 30k 30k 10k 12k
h/k part number 110-16303J26 110-16103j26 110-16123j26
NOTE: · · Lack of this modification is unlikely to generate a complant It will have no effect in applications when the SUB input is used, or when the sub amp is used with the FILTER switch in the OFF position.
Model SUB-TS7 SUB-TS7
Serial Number (120v) ME048503390 and below ME048503391 and above
Serial Number (230v) ME048708198 and below ME048708199 and above
Status In need of filter modification Modified by Factory
Action Change value of R223,224,226,227 None Required
14
SUB-TS7/TS8
harman/kardon
15
SUB-TS7/TS8
harman/kardon
16
SUB-TS7/TS8
harman/kardon
17
SUB-TS7/TS8
harman/kardon
18
SUB-TS7/TS8
harman/kardon
19
SUB-TS7/TS8
harman/kardon
SUB-TS7/TS8 120V Electrical parts list
Part number LIMITER PCB Resistors 110-16103j26 110-16153j26 110-16223j26 110-16333j26 110-16474j26 110-16751j26 110-16755j26 Capacitors 135-3226m50 135-3476m25 130-2f104z503 132-103j503 162-10059001 Semiconductors 190-16tl074cn 192-027c1815gr 197-131n4148 Miscellaneous 162-50159002 175-9f40hr2 PREAMP PCB Resistors 110-12472j52 110-16102j26 110-16103j26 110-16104j26 110-16105j26 110-16122j26 110-16124j26 110-16151j26 110-16154j26 110-16183j26 110-16203j26 110-16205j26 110-16223j26 110-16273j26 110-16472j26 110-16473j26 110-16512j26 110-16513j26 110-16752j26 110-16913j26 115-h503a102 Capacitors 129-a154j633 129-a224j633 130-2b221k503 130-2b470k503 130-2f104z503 Mylar capacitor 0.15U 63V ±5% MSC Mylar capacitor 0.22uF 63V ±5% MSC disk capacitor 220P 50V ±10% disk capacitor 47P 50V ±10% disk capacitor 0.1U 50V +80/-20% C221,C222, C218 C200,C204,C205,C207,C208,C210,C211,C212, C214,C220,C230,C237, C229, C232,C242,C244,C245,C246,C252,C254,C256, Resistor4.7K 1/2W ±5% CF 52mm Resistor 1K 1/6W ±5% CF 26mm Resistor 10K 1/6W ±5% CF 26mm Resistor 100K 1/6W ±5% CF 26mm Resistor 1M 1/6W ±5% CF 26mm Resistor 1.2K 1/6W ±5% CF 26mm Resistor 120K 1/6W ±5% CF 26mm Resistor 150 1/6W ±5% CF 26mm Resistor 150K 1/6W ±5% CF 26mm Resistor 18K 1/6W ±5% CF 26mm Resistor 20K 1/6W ±5% CF 26mm Resistor 2M 1/6W ±5% CF 26mm Resistor 22K 1/6W ±5% CF 26mm Resistor 27K 1/6W ±5% CF 26mm Resistor 4.7K 1/6W ±5% CF 26mm Resistor 47K 1/6W ±5% CF 26mm Resistor 5.1K 1/6W ±5% CF 26mm Resistor 51K 1/6W ±5% CF 26mm Resistor 7.5K 1/6W ±5% CF 26mm TA Resistor 91K 1/6W ±5% CF 26mm Variable resistor RV16AE-20B2-15K-A54-104(A50K) R201,R202, R213,R214,R215,R254,R209,R212,R216,R217, R218,R220,R221,R222,R225,R228,R229,R230, R232,R235,R240,R248,R260,R270, R231,R263,R266, R259, R265, R233, R253, R252, R262, R237,R238, R257, R247,R255,R256, R226,R227, R200,R207,R258, R219,R249,R250,R251,R264 R210,R211, R223,R224, R234, R203,R204,R205,R206, VR201 7PIN 150mm AWG26 UL 2468 connector 40PIN PITCH=2.54mm P302, I.C TL074CN ST QUAD OP-AMP+B78 Transistor 2SC1815GR NPN Diode1N4148 26mm U301, Q301,Q302, D301,D302, Elec. Capacitor 22U 50V ±20% Elec. Capacitor 47U 25V ±20% disk capacitor 0.1U 50V +80/-20% Mylar capacitor 0.01U 50V ±5% Single wire 50mm WHITE UL1007 AWG26 C301, C304, C305,C306, C302,C303, Resistor 10K 1/6W ±5% CF 26mm Resistor 15K 1/6W ±5% CF 26mm Resistor 22K 1/6W ±5% CF 26mm Resistor 33K 1/6W ±5% CF 26mm Resistor 470K 1/6W ±5% CF 26mm Resistor 750 1/6W ±5% CF 26mm Resistor 7.5M 1/6W ±5% CF 26mm R301,R303,R304,R308,R309,R314, R302, R310,R312, R305, R307, R311,R313, R306, Description Reference Designator
20
SUB-TS7/TS8
Part number PREAMP PCB 132-183j503 132-223ja03 132-473j503 132-563j503 132-823j503 135-3105m50 135-3106m50 135-3107m16 135-3226m50 135-3227m16 Semiconductors 192-027c1815gr 197-131n4148 199-15000335 162-50332003 190-06m4558d 190-16tl074cn Miscellaneous 162-a016d001 174-0rca313v 174-20810360g 175-1b08v01 180-tms7210v 362-FE-00041 MAIN PCB Resistors 110-14472j26 110-14681j26 110-16101j26 110-16102j26 110-16103j26 110-16105j26 110-16123j26 110-16152j26 110-16153j26 110-16154j26 110-16181j26 110-16182j26 110-16223j26 110-16332j26 110-16392j26 110-16393j26 110-16470j26 110-16471j26 110-16472j26 110-16473j26 110-16560j26 110-16563j26 110-16682j26 110-10821jk2 110-122r2j15 110-20331jk2 113-50r10j10 114-03302m0 Resistor 4.7K 1/4W ±5% CF 26mm Resistor 680 1/4W ±5% CF 26mm Resistor 100 1/6W ±5% CF 26mm Resistor 1K 1/6W ±5% CF 26mm Resistor 10K 1/6W ±5% CF 26mm Resistor 1M 1/6W ±5% CF 26mm Resistor 12K 1/6W ±5% CF 26mm Resistor 1.5K 1/6W ±5% CF 26mm Resistor 15K 1/6W ±5% CF 26mm Resistor 150K 1/6W ±5% CF 26mm Resistor 180 1/6W ±5% CF 26mm Resistor 1.8K 1/6W ±5% CF 26mm Resistor 22K 1/6W ±5% CF 26mm Resistor 3.3K 1/6W ±5% CF 26mm Resistor 3.9K 1/6W ±5% CF 26mm Resistor 39K 1/6W ±5% CF 26mm Resistor 47 1/6W ±5% CF 26mm Resistor 470 1/6W ±5% CF 26mm Resistor 4.7K 1/6W ±5% CF 26mm Resistor 47K 1/6W ±5% CF 26mm Resistor 56 1/6W ±5% CF 26mm Resistor 56K 1/6W ±5% CF 26mm Resistor 6.8K 1/6W ±5% CF 26mm Resistor 820 1W ±5% Resistor 2.2 1/2W ±5% Resistor 330 2W ±5% 5mm Cermemt resistor 0.1 5W ±5% Variable resistor 3K 0.3W ±20% R147,R150, R148,R151, R120, R124, R134, R143, R135,R139, R103,R123,R136,R137,R141,R142, R118,R145,R152,R154, R131, R111,R114 R153, R128,R129,R133, R106,R107,R144 R105,R108, R126, R112,R113,R115,R116, R140, R110,R125,R130, R101, R117, R104, R109, R132, R127, R146,R149, R121,R122, R138, wire assembly UL1007 160/80mm#26 RCA JACK RCA-313G V/R/W SPK JK BP 8PIN connector 8 PIN PITCH=2.0mm SWITCH SLIDE 6PIN MS7210V PCB bracket 11.75*8.5*12.5H JK201, JK202, SW201,SW202,SW203, Transistor 2SC1815GR NPN Diode 1N4148 26mm ZENER diode 3.3V 1/2W 52mm 2PIN 330mm RED/GREEN LED I.C. OPA 4558D Dual Op-Amp I.C TL074CN ST Quad Op-Amp Mylar capacitor 0.018uF 50V ±5% Mylar capacitor 0.022uF 100V ±5% Mylar capacitor 0.047U 50V ±5% Mylar capacitor 0.056U 50V ±5% Mylar capacitor 0.082U 50V ±5% elec. capacitor 1U 50V ±20% Elec. Capacitor 10uF 50V ±20% Elec. Capacitor 100uF 16V ±20% Elec. Capacitor 22U 50V ±20% Elec. Capacitor 220U 16V ±20% Description Reference Designator
harman/kardon
C223, C215, C224, C216, C217, C228, C201,C202,C206,C213,C219,C231,C241,C243, C251,C253, C234, C225, C233,
Q201,Q206,Q207,Q208, D201,D202,D203,D204,D205,D206,D207,D208, D214,D215,D216, D213, D209, U203, U201,U202,
21
SUB-TS7/TS8
Part number MAIN PCB Semiconductors 192-027c1815gr 192-028a1015gr 192-1672n5551 192-1682n5401 197-131n4148 199-15000335 199-15000625 199-15001605 192-021c1815gr 192-021tip35c 192-022tip36c 192-201d882y 192-202b772y 192-991d669a 192-992b649t 197-00kbl405 197-101n4002 190-06m4558d Capacitors 130-2b102k503 130-2f104z503 130-3f473m503 130-sl101k503 132-104j503 132-223ja03 135-3105m50 135-3107m16 135-3226m50 135-3227m10 135-3227m16 135-3476m25 130-3f472md00 132-223ja03 135-3107m16 135-4688m50 Miscellaneous 171-udhss124d 175-1c07v01 175-1d02v01 175-1d03v01 193-3m2520 relay 5A 24V UDH-SS124D connector 7PIN PITCH=2.5mm connector 2PIN PITCH=3.96mm connector 3 PIN PITCH=3.96mm Insulator TO-3P 25x20mm RY101, P101, P102, P103, for Q107,Q108, disk capacitor 1000P 50V ±10% disk capacitor 0.1U 50V +80/-20% disk capacitor 0.047U 50V ±20% disk capacitor 100P 50V SL ±10% Mylar capacitor 0.1U 50V ±5% Mylar capacitor 0.022uF 100V ±5% elec. Capacitor 1U 50V ±20% Elec. Capacitor 100uF 16V ±20% Elec. Capacitor 22U 50V ±20% Elec. Capacitor 220U 10V ±20% Elec. Capacitor 220U 16V ±20% Elec. Capacitor 47U 25V ±20% disk capacitor 4700P 400V ± 20% Mylar capacitor 0.022uF 100V ±5% Elec. Capacitor 100uF 16V ±20% Elec. Capacitor 6800U/50V ±20% C116, C108,C113,C115,C119, C106, C139,C140, C107, C124,C125,C126,C128, C105,C112, C109,C117,C120, C114,C118, C129,C130, C111, C103, for Power Switch C123,C127, C110, C121,C122, Transistor 2SC1815GR NPN Transistor 2SA1015GR PNP Transistor 2N5551 NPN Transistor 2N5401 AI-PNP 350V Diode 1N4148 26mm ZENER diode 3.3V 1/2W 52mm ZENER diode 6.2V 1/2W 52mm ZENER diode 16V 1/2W 52mm Transistor 2SC1815GR NPN Transistor TIP35C NPN Transistor TIP36C PNP Transistor KSD882Y NPN Transistor KSB772Y PNP TransistorHI-SINCERITY HSD669A NPN Transistor HSB649T PNP bridge diode 4A 500V KBL405 Diode 1N4002 I.C. OPA 4558D Dual Op-Amp Q102,Q111,Q112,Q113,Q118 Q114,Q116, Q103,Q109, Q104,Q110, D101,D103,D105,D108, D102, D106,D107, D109, Q101,Q115, Q107, Q108, Q117, Q119, Q106, Q105, D110, D104, U101, Description Reference Designator
harman/kardon
MISCELLANEOUS/MECHANICAL 323-AL-00020 351-AM03014A094 352-AM03008D040 361-FE-00051 361-NYL-00054 150-e8604107 152-u602015 154-u25006t0 155-520020 162-10082007 162-a040d001 176-wjce1 180-pbr12c11s 302-AL-00435-0BA HEAT SINK 65*32*31 SCREW M3*14 BLK SCREW 3*8 B type Transistor holder 14.2*8.0*5.2 Transistor Insulator (SW06002) Power Transformer EI-86 60Hz 120V TT0869906580 AC Line cord SVT FT-2 fuse 2.5A 250V 20mm fuse holder R3-11 WIRE RED 18AWG 80mm Speaker cable #1015 400mm 991110-00 terminal CE-1 Power switch PUSH BR12C11S Alum. Back panel 270*215*2.5T HKTS7 Alum. Back panel 270*215*2.5T HKTS8
22
SUB-TS7/TS8
Part number Description Reference Designator
harman/kardon
MISCELLANEOUS/MECHANICAL 306-ABS-00004 311-ABS-00028 320-RUB-00033 323-AL-00019 333-EVA-00096 333-EVA-00097 333-EVA-00132 333-EVA-00133 333-EVA-00188 333-EVA-00220 335-NYL-00002 350-EM04012D024 351-AM03008A079 351-HM04016A218 352-AM03010D063 352-AM03010D065 354-GM04002 362-FE-00013 REAR CABINET 268*213*102 A.B.S UL knob 46077-W P.V.C. Rubber pad 25*21*4t HEAT SINK 117.5*60*25 EVA (Gasket) 213*15*2.0mm EVA (Gasket) 213*15*1.0t EVA (Gasket) 238*15*2.0mm EVA (Gasket) 238*15*1.0t EVA (Gasket) 170x5x1t EVA (Gasket) 225*15*1t UL bushing 4K-4 NO-BB SCREW 4 *12 BLK SCREW M3*8 BLK SCREW M4*16 SCREW 3*10 B type SCREW 3*10 P type M4 NUT BLK PCB bracket L TYPE t=1.6mm
R-4
R/C-4 BRKT-2,PCB TO BRKT-4 R-4 R/P-6,R/P TO H/S-2 -2,RCA JK-1 R-4
23
SUB-TS7/TS8
harman/kardon
24
SUB-TS7/TS8
harman/kardon
25
SUB-TS7/TS8
harman/kardon
HKTS7
26
SUB-TS7/TS8
harman/kardon
HKTS7
27
SUB-TS7/TS8
harman/kardon
HKTS8
28
SUB-TS7/TS8
harman/kardon
HKTS8
29
SUB-TS7/TS8
harman/kardon
HKTS8
30
SUB-TS7/TS8
harman/kardon
HKTS7
31
SUB-TS7/TS8
harman/kardon
HKTS 8
®
OWNER'S MANUAL 406-000-05108 WARRANTY CARD 405-000-00333 COLOR CODE 413-000-05097 FOAM PACKING 431-00005154 WIRES: GREEN 20FT CENTER 370-000-05002 WHITE 20FT FRONT SATS 370-000-00092 RED 20FT 370-000-00265 GREY 40FT REAR SATS 370-000-00264 BLUE 40FT REAR SATS 370-000-00256 PURPLE RCA SUB CABLE 370-000-00261 BROWN 40FT REAR SATS 370-000-00257
Packaging
SATELLITES (5) HKTS 8 SAT-1 FOAM PACKING 431-00005153
CENTER CHANNEL HKTS 8 CEN-1 MOUNTING BRACKETS (5) 326-ABS-00108 SAT/CENTER CARTON 401-000-05023 SCREW PACKAGE (1 SET) 371-000-05048 MOUTING PLATES (5) 326-FE-00109 TERMINAL COVER (5) 317-PS-00172 PLASTIC BAG
HKTS 8 SUBWOOFER (SUB TS8)
CLOTH
PACKING 431-000-05037 OUTER CARTON 402-000-05185
32