Text preview for : 1999_sewing_machine_®_.pdf part of ELNA 6005 service manual sewing machine [printed in switzerland] - pag. 36
Back to : 1999_sewing_machine_®_.pd | Home
PDFMAILER.DE
Elna 6005 Heirloom Edition
SERVICE MANUAL
11/99
Printed in Switzerland
395902-42
PDFMAILER.DE
CONTENTS
WIRING AND ELECTRONIC CHECK Wiring diagram General trouble shooting procedure What to do when Electronic quick check 1 2 3-5 6-7
SERVICE ACCESS Face cover Top cover Belt cover Base plate Bed cover Front cover Rear cover 8 8 9 10 10 11 12
MECHANICAL ADJUSTMENT Needle centring Needle bar height Hook and feed timing Clearance Backlash of hook drive gear and lower shaft gear Feed dog height Needle bar swing sensor Upper and lower tension Stretch stitch feed balance Buttonhole Presser bar height and alignment 13 14 15 16 17 18 19 20 21 22 23
REPLACEMENT Threader plate C-Board and Fuse Transformer Receptacle A-Board K and F-Board DC Motor Buttonhole Upper shaft sensor Zigzag stepping motor Feed stepping motor 24 25 26 27 28 29 30 31 32 33 34
PDFMAILER.DE
1
Wiring Diagram
NAME OF ELECTRONIC PARTS AND WIRING Each connector should be connected as follows
A: B: C: D: E: F:
THREAD TENSION SWITCH BUTTONHOLE SENSOR UPPER SHAFT SENSOR SEWING LIGHT C-BOARD FEED STEPPING MOTOR
G: ZIGZAG STEPPING MOTOR H: DC MOTOR I: F-BOARD J: K-BOARD K: RECEPTACLE (SECONDARY) L: A-BOARD
PDFMAILER.DE
GENERAL TROUBLE SHOOTING PROCEDURE
2
MACHINE DOESN'T WORK WELL
PDFMAILER.DE
3
1. CONDITION Skipping stitches.
WHAT TO DO WHEN
CAUSE 1. Needle is not inserted properly. 2. Needle is bent or worn. 3. Incorrectly threaded. 4. Needle or thread is inappropriate for fabric being sewn. 5. Sewing on stretch fabric 6. Presser foot pressure is too weak. 7. Inappropriate needle bar height. 8. Inappropriate needle to hook timing. 9 Inappropriate needle to shuttle clearance. 2. Fabric not moving. 1. Presser foot pressure in too weak. HOW TO FIX 1. Insert the needle properly. 2. Change the needle. 3. Retread. 4. Use the recommended sewing needle and thread. 5. Use a No. 11 blue tip needle. 6. Adjust the presser bar level to make the pressure stronger. 7. See mechanical adjustment "Needle bar height" 8. See mechanical adjustment "Needle to shuttle timing". 9. See mechanical adjustment "Clearance between needle and hook". 1. Adjust the presser bar level to make the pressure stronger. 2. See mechanical adjustment "Feed dog height". 3. Raise the feed dog level. REFERENCE
Page 14
Page 15 Page 16
2. Incorrect feed dog height. 3. Feed dog is in down position. 4. Thread on bottom side 4. Make sure to bring both of fabric is jammed up. needle and bobbin. 5. Feed dog teeth are 5. Thread under the foot when worn. starting sewing. 3. Breaking upper thread. 1. Initial sewing speed is too fast. 2. Thread path is incorrect. 3. Needle is bent or dull. 4. Upper thread tension is too strong. 5. Needle size is inappropriate for fabric. 6. Needle eye is worn. 7. Needle hole in needle plate is worn or burred. 1. Incorrectly threaded bobbin. 2. Too much thread is around on the bobbin. 3. Lint is stuck inside the bobbin holder. 4. Thread quality is too low. 5. Thread is jamming around the bobbin. 1. Start with medium speed. 2. Use the proper thread path. 3. Replace with a new needle. 4. Adjust needle thread tension correctly. 5. Use appropriate needle for Fabric and thread in use. 6. Change the needle. 7. Repair the hole or replace the needle plate. 1. Thread bobbin correctly. 2. Adjust the position of stopper. 3. Clean the hook race 4. Change to a high quality sewing thread. 5. Clean out the jamming thread.
Page 18
Page 20
4. Breaking bobbin thread.
PDFMAILER.DE
WHAT TO DO WHEN
CONDITION 5. Needle breaks. CAUSE 1. Needle is hitting the needle plate. 2. Needle is bent or worn. 3. Needle is hitting the hook. HOW TO FIX See mechanical adjustment "Needle position". Change the needle. See mechanical adjustment "Clearance between needle and hook. See mechanical adjustment "Zigzag synchronisation". Page 19 REFERENCE
4
4. The fabric moves while the needle is piercing it or the needle zigzag while in fabric. 5. Fabric is being pulled too strongly while sewing.
Guide the fabric gently while sewing.
6. Noisy operation.
1. Backlash between shuttle hook gear and lower shaft gear is too great. 2. Lower shaft gear is loose. 3. Inappropriate belt tension.
See mechanical adjustment "Backlash (lower shaft gear)".
Page 17
Eliminate the looseness.
See part removal and replacement "Driving motor (DC motor)". Oil all moving parts.
Page 30
4. Not enough oil.
7. Deformation pattern
1. Inappropriate feed balance. 2. Inappropriate zigzag synchronisation. 3. Upper thread tension is too strong.
See mechanical adjustment "Stretch stitch feed balance. See mechanical adjustment "Zigzag synchronisation". See mechanical adjustment "Needle thread tension".
Page 21
Page 19
Page 20
PDFMAILER.DE
5
A Operation 1
DIAGNOSIS CHART
Be cautious of sudden running of the machine when turning on the power switch. If nothing is happened on the machine when the power switch is turned on, turn off the power switch and check the following points: Step 1: Make sure that all of the connectors are connected properly. Disconnect the power supply cord from the machine and go to the Step 2. Step 2: Replace the machine socket, then turn the power switch on. If nothing is happened, turn off the power switch and go to the Step 3. Step 3: Replace the printed circuit board A, then turn the power switch on. If nothing is happened, turn off the power switch and go to the Step 4. Step 4: Replace the printed circuit board C, then turn the power switch on. If nothing is happened, turn off the power switch and go to the Step 5. Step 5: Replace the transformer unit, then turn the power switch on. If nothing is happened, turn off the power switch and go to the Step 6. Step 6: Replace the fuse. If lamp does not light up when turning on the power switch, turn off the power switch. Then check the following points: Step 1: Replace the lamp bulb, then turn on the power switch. If nothing is happened, turn off the power switch and no to the Step 2. Step 2: Replace the printed circuit board A. Then turn on the power switch. If LCD (Liquid Crystal Display) shows nothing when turning on the power switch, turn off the power switch and check the following points: Step 1: Replace the printed circuit board K. Then turn on the power switch, If nothing is happened, turn off the power Switch. and go to the Step 2. Step 2: Replace the printed circuit board A, Then turn on the power off the power switch. If machine continue to sew the same part of a stitch, turn off the power switch and check the following points: Step 1: Replace the printed circuit board A. Then turn on the power switch. If nothing is happened, turn off the power switch and go to the Step 2. Step 2: Replace the stepping motor for zigzag and/or feed. If nothing is happened, turn off the power switch and go to the Step 3. Step 3: Replace the lamp bulb.
Operation Preparation (Use diagnosis chart).
Preparation 1. Turn off the power switch. 2. Set the bobbin winder spindle to the left. 3. Raise the feed dog. 4. Shift the speed setting lever to the left. 5. Remove the presser foot and lift up the presser foot lever. 6. Move the needle bar to up position. 7. Connect the foot control to the machine.
If defect is found during the Step 01, turn off the power switch and take the following steps:
Step 1 Replace the printed circuit board F. Then check the machine. Step 2: Replace the printed circuit boards K. Then check the machine. Step 3: Replace the printed circuit boards A. Then check the machine.
If defect is found on the Step 02, turn off the power switch and take the following steps:
Step 1: Replace the printed circuit board F. Then check the machine. Step 2: Replace the printed circuit board K. Then check the machine. Step 3: Replace the printed circuit board A. Then check the machine. To proceed further step, press.
"M" button on correct condition. "C button on defect condition.
PDFMAILER.DE
DIAGNOSIS CHART
1. Step Step LCD, LED test. Test operation Turn on the power switch while pressing "REVERSE", AUOLOCK", THEN PRESS "1" within 2 seconds. 1.
6
2. Step Keys
3. Step Buttonhole.
Press the keys shown below in order. "Reverse, Auto-Lock, U/D, Twin Needle, Width -, Width +, Length -, Length +, Clear, Enter, TurnOver, Memory, Mode, and stitch patterns 1 to 0. 1. Pull down the 1 buttonhole lever. 2. Move the 2 buttonhole lever back and forth. 3
Correct condition Defect condition LCD shows (Special If the machine does not go to Mode). Test mode, replace the 2. LCD shows (Self-Check following parts in order and Start). recheck 3. Buzzer sounds. 1. Printed circuit board F 4. The 6 LED blinks. 2. Printed circuit board K Press Enter to the next test. 3. Printed circuit board A 4. Printed circuit board L 1. Buzzer sounds. If buzzer does not sound when 2. LCD shows (Key). you press the key, replace the 3. Each time you press the following parts in order and key, buzzer sounds. recheck. 4. It goes to the Step (3) 1. Printed circuit board F. automatically if in correct 2. Printed circuit board K. condition. 3. Printed circuit board A.
4. Step Bobbin winder switch.
1
2
5. Step Tension switch.
1
Shift the bobbin winder spindle to the right. Shift the bobbin winder spindle to the left. Turn the thread tension dial.
Buzzer sounds and LCD shows (BH Sensor L). LCD shows (BH Sensor H) when the sensor is closed. LCD shows (BH Sensor L). when the sensor is open. 1. Buzzer sounds each time and LCD shows (Spool).
If machine does not work properly, replace the following parts in order and recheck. 1. Buttonhole sensor. 2. Printed circuit board K. 3. Printed circuit board A.
If not working, replace the following parts in order and recheck. 1. Printed circuit board K. 2. Printed circuit board A. If not working, replace the following parts in order and recheck. 1. Printed circuit board K. 2. Printed circuit board A. 3. Printed circuit board L. If not working properly, replace the following parts in order and recheck. 1. Upper shaft sensor. 2. Printed circuit board A.
1 2 3
6. Step Upper shaft sensor.
1
Turn the balance 1 wheel toward you to move the needle 2 bar from the highest to the lowest position, then from the 3 lowest to the highest position. Turn the balance 1 wheel toward you to move the needle 2 bar from the highest to the lowest position. Then press "Reverse" key. Turn the balance 1 wheel toward you to move the needle 2 bar from the highest to the lowest position. Then press
7. Step Stepping motor for zigzag.
1
Buzzer sounds and LCD shows (Thread Tension). LED turns on when the dial is state "Auto". LED turns off when dial is turned from "Auto". Buzzer sounds and LCD shows (PH Sensor L,H). LCD shows (PH Sensor L,H), when the needle bar is moved from the lowest to the highest. LCD shows (PH Sensor H,L), when the needle bar is moved from the highest to the lowest. Buzzer sounds and LCD shows Zigzag motor. The stepping motor moves to the primary setting position.
If not working, replace the following parts in order and recheck. 1. Stepping motor for zigzag. 2. Printed circuit board A.
8. Step Stepping motor for feed.
1
Buzzer sounds and LCD shows (Feed motor). The stepping motor moves to the primary setting position. (feed at "O").
If not working properly, replace the following parts in order and recheck. 1. Stepping motor for feed. 2. Printed circuit board A.
PDFMAILER.DE
"Reverse" Key.
7
9. Step Step Foot control. 1
DIAGNOSIS CHART
Test operation Depress the foot control as far as it will go. Then release it. 1 2 Correct condition Buzzer sounds and LCD shows (controller). Buzzer sounds when the foot controller is depressed and released. Defect condition If not working properly, replace the following parts in order and recheck. 5. Foot control. 6. Machine socket. 7. Printed circuit board A. Buzzer sounds and LCD If not working properly, replace shows (Volume). the following parts in order Buzzer sounds at the and recheck. leftmost and the rightmost 1. Printed circuit board K. positions. 2. Printed circuit board A. Buzzer sounds and LCD If machine does not work shows (DC Motor). properly, replace the following The machine runs at low parts in order and recheck. speed, then at high speed 1 Buttonhole sensor. and stops at the highest 2 Printed circuit board K. position automatically. 3 Printed circuit board A.
10. Step Speed control lever.
1
11. Step Buttonhole.
1
Move the speed control lever from the leftmost position to the rightmost position. Press the Reverse button.
1 2
1 2
When the check is completed, LCD shows (SELF CHECK END). If the machine works properly, LCD shows (SELF CHECK OK). If not , LCD shows ( ERROR O ) then it shows the part to be replaced by the following letters: A Printed circuit board A D Driving motor P Upper shaft sensor Y Stepping motor for feed B Buttonhole sensor K Printed circuit board K R Machine socket C Foot control L Light bulb X Stepping motor for ZZ
PDFMAILER.DE
FACE AND TOP COVER
FACE COVER To remove 1. Remove the cap A and set screw B. 2. Remove the face plate D while pulling it toward you so that face plate hook C is released. To attach 1. Attach the face plate. 2. Tighten the set screw B and attach the cap A. TOP COVER To remove 1. Remove the set screw F. 2. Lift up the handle H and remove the set screw E. 3. Close the top cover lid G and pull the top cover to the back. To attach 1. Lift up the handle H and insert the top cover G from the back. 2. Tighten the set screws F and G.
8
PDFMAILER.DE
9
BELT COVER
To remove 1. Remove the cap A 2. Remove the screws B and D 3. Lift up the handle F and loosen the screws E To attach 1. Attach the belt cover C with the screws B, D and E 2. Attach the cap A
PDFMAILER.DE
BASE PLATE AND BED COVER
10
Base plate
To remove 1. Remove the screw A and 4 screws B 2. Remove the base plate C. To attach 1. Reverse this procedure
Bed cover
To remove 1. Remove the 2 screws D 2. Remove the bed cover E To attach Move the drop lever F to the left and attach the bed cover with the screws D.
PDFMAILER.DE
11
FRONT COVER
To remove 1. Remove the face cover, top cover, belt cover and bed cover (see pages 8, 9, and 10). 2. Remover the screw A and loosen the screws B, C, D, E, F and G. 3. Pull out the connector H and remove the front cover K. To attach Reverse this procedure
PDFMAILER.DE
REAR COVER
12
To remove 1. Remove the face cover, top cover, belt cover and bed cover (see pages 8, 9, and 10). 2. Loosen the screws A, B, C and D. 3. Remove the cap E and remove the screw F. 4. Remove the rear cover while pulling it toward you and pushing it to the left. Unhook the projection G and twist the rear cover to clear the presser bar lifter area. To attach Reverse this procedure.
PDFMAILER.DE
13
NEEDLE CENTRING
When selecting pattern N°. 1, the needle should be in centre position of needle slot in the needle plate, or when the needle swing is in maximum zigzag width, the distance between both sides of needle slot in the needle plate and the needle positions should be equal. If not, adjust as follows: 1. 2. 3. 4. 5. Turn on the power switch. Select pattern 1 or pattern 2 at maximum zigzag width. Loosen the screw A. Turn the eccentric pin B to adjust the needle centring. Tighten the screw A Check the hook timing after this adjustment.
Note:
PDFMAILER.DE
NEEDLE BAR HEIGHT
14
A regular needle #14 should be used for this adjustment. The distance between the upper edge of needle eye and the tip of shuttle hook should be in the range of 1.6 - 2.0 mm when the tip of shuttle hook meets the right side of the needle as the needle is moved up from its left and lowest position by turning the handwheel toward you. 1. 2. 3. 4. 5. Remove the needle plate and bobbin holder. Turn on the power switch and select pattern (no. 2). Turn the handwheel toward you until tip of shuttle hook meets the right side of the needle. Loosen the needle bar connecting stud set screw A. Adjust the height of the needle bar by moving the needle bar upward or downward without turning it. (Make sure the needle setting groove of the needle bar is in the front). 6. Tighten the set screw A. 7. Insert the bobbin holder and attach the needle plate.
PDFMAILER.DE
15
HOOK AND FEED TIMING A regular needle B #14 should be used for this adjustment. Select pattern 2. Turn the handwheel toward you to position the needle bar from its lowest position, moving up approximately 2,30 mm to 2,60 mm. At this position, the tip of the hook should meet the right side of the needle. 1. 2. 3. 4. 5. Remove the needle plate and the bobbin holder. Turn on the power switch and select pattern 2. Remove the top cover, belt cover and bed cover (See pages 8, 9 and 10). Turn the handwheel toward you and set the needle bar to its lowest position. In this condition, the peg C on the feed lifting cam should be in its lowest position. If not: loosen the set screws A of upper shaft belt wheel. With the needle bar in its lowest position, hold the handwheel in place while turning the upper shaft belt to position the peg C on the feed lifting cam in its lowest position. Tighten the set screws A of upper shaft belt wheel Set the needle bar to its lowest position, fit the timing gauge 101360 in contact with the needle bar cradle, then loosen one of the lower shaft hook gear screw D. Turn the balance wheel slowly forwards until the gauge butts. In this position, the hook should be between the 2 positions illustrated Unscrew the second screw of lower shaft hook gear and adjust the position of the hook. Tighten the screws D, turn balance wheel several times and recheck the timing and refit the machine.
6. 7. 8. 9.
PDFMAILER.DE
CLEARANCE
The clearance between the needle and the point of hook should be +0.05 0.1 mm. If not, adjust as follows: 1. 2. 3. 4. 5. 6. 7. 8. Remove the needle plate and bobbin case. Replace the needle with master needle D. Turn on the power switch and select pattern 2. Loosen the set screws A, B, C and slightly loosen the hinge screw C. Turn the handwheel and adjust the clearance between the master needle and the point of shuttle hook in the left and right needle positions to +0.05 -0.1 mm by moving the shuttle hook set plate E up or down. Tighten the set screws A B and C. Replace the master needle D with the needle. Insert the bobbin case and attach the needle plate.
16
PDFMAILER.DE
17
BACKLASH OF HOOK DRIVE GEAR AND LOWER SHAFT GEAR
The backlash of the gears should be smooth and should be less than 0.8 mm when the point of the hook is under the feed dog. To 1. 2. 3. check: Turn the power switch off. Remove the needle plate and bobbin holder. Turn the handwheel slowly toward you until the tip of the shuttle hook A is between both ends B of feed dog. 4. Rotate the hook race clockwise and counter clockwise by finger. Check the play. It should be within 0.8 mm.
If there is more than 0.8 mm, adjust as follows: 1. Remove the bed cover and loosen the screw C. 2. Turn the lower shaft bushing D eccentric, in the direction E when the play at shuttle hook tip is too small. 3. Turn the lower shaft bushing D eccentric, in the direction F when the play at shuttle hook tip is too large. 4. Tighten the screw C securely after adjustment.
PDFMAILER.DE
FEED DOG HEIGHT
18
The highest position of the feed dog should be between 0.80 and 0.90 mm from the surface of the needle plate when the pressure dial is set at 3 and the presser foot is lowered. 1. 2. 3. 4. 5. 6. 7. Set the pressure dial at 3 and lower the presser foot. Turn on the power switch. Remove the bed cover (see page 10). Turn the balance wheel toward you to set the feed dog at the highest position. Loosen the screw A and the nut B. Adjust the feed dog height by turning the adjusting screw C. Tighten the nut B and the screw A.
PDFMAILER.DE
19
NEEDLE BAR SWING / SENSOR
NOTE: When the machine is set to maximum zigzag width, the needle should start to swing laterally between 6.3 to 7.5 mm above the needle plate. 1. 2. 3. · Remove the top cover (see page 1). Turn on the power. Select zigzag pattern no. 2 and set the zigzag width to maximum. Slowly turn the handwheel toward you until the needle starts to swing. If higher than 7.5 mm, loosen the screw C and turn the sensor disk F in direction A. · If lower than 6.3 mm, loosen the screw C and turn the sensor disk F in direction B. 4. Set the sensor disk F as close as possible to the sensors D (it should not touch the upper shaft sensor. Tighten the screw C. 5. Turn the handwheel several times toward you and recheck the start of the needle swing. 6. Fix the upper cover.
PDFMAILER.DE
UPPER AND LOWER TENSION
Check: Set the upper thread tension dials F to 3. The standard upper tension should be 75 - 90g when pulling the thread (cotton thread 50/3) in direction C.
20
Adjust the upper tension: 1. Set the thread tension dial F to 3. 2. Open the face plate and adjust the thread tension by turning the thread tension screw D in the direction of A for loosen the tension B for tighten the tension 3. Close the face plate. Check: The correct factory setting of the lower thread tension is 9 to 11 g, measured with a cotton thread no 50/3. Adjust the lower tension: 1. Turn the screw E to adjust the lower tension in direction to A for loosen the tension B for tighten the tension.
PDFMAILER.DE
21
STRETCH STITCH FEED BALANCE
When pattern "8" is sewn with the feed balancing dial at the standard setting mark, figure D, the stitch pattern should be as shown below. 1. 2. 3. 4. 5. 6. see
Turn on the power switch while pushing the reverse button, and then select the pattern No. 8 within 2.5 seconds. "CHECK PATTERN (8) will appear in the screen. Set the feed balancing dial D at the standard setting mark. Sew the pattern "8" (The machine will stop automatically after sewing eight stitch pattern). Remove the base (see page 10). Adjust the stretch stitch feed balance by turning the adjusting screw in the direction A or B. Attach the base.
PDFMAILER.DE
BUTTONHOLE
22
A) BUTTONHOLE LEVER GUIDE 1. Attach the automatic buttonhole foot R. 2. Loosen the set screw A and leave the clearance of 2.9 mm between the spring holder C and slider B by moving the buttonhole lever guide C in this condition the buttonhole lever E should touch the spring holder C slightly. 3. Tighten the set screw A. B. BUTTONHOLE SENSOR 1. Turn the power switch on while pressing the reverse button, and then press BH1 at once. "BH SENSOR H or L" will appear in the screen. 2. Lower the buttonhole lever E. Then leaves the clearance of 1.6mm between the slider B and spring holder C. 3. Loosen the set screw G and move the buttonhole sensor base plate F from the right to left slowly. At the position where the screen message changes from "BH SENSOR L" to "BH SENSOR H", tighten the set screw G. 4. When the clearance between the spring holder C and slider B is: * 1.4 mm, the screen shows "BH SENSOR H". * 1.8 mm, the screen shows "BH SENSOR L".
PDFMAILER.DE
23
PRESSER BAR HEIGHT AND ALIGNMENT
To check: 1. Raise the presser foot lever B. 2. The distance between the zigzag foot A and the needle plate C should be 6.0 mm. If the height is greater or less than 6 mm, adjust as follows. To adjust: 1. Remove the face cover (see page 8). 2. Raise the presser foot lever B and loosen the screw D on the presser bar holder E. 3. Adjust the distance between the zigzag foot A and the needle plate C to 6.0 mm. 4. Tighten the screw D securely. Note: When you tighten the screw D, make sure that both sides of the zigzag foot A are paralleled with the feed dog slits G. 5. Attach the face cover.
PDFMAILER.DE
THREADER PLATE
24
When the hook of the threader plate is damaged, change or adjust the part as follows. To change the threader plate: 1. Raise the needle to its highest position and lower the threader knob A to its lowest position. 2. Loosen the screw B and remove the threader plate (Fig. A). To change the needle threader: 1. If the hook of the threader plate F touches left or right side, loosen the screw D and adjust the hook position (Fig. B). 2. If the hook of the threader plat F touches the top or bottom side of the needle hole, loosen the screw E and adjust the hook position (Fig. C).
PDFMAILER.DE
25
C-BOARD AND FUSE
To remove: 1. Remove the front cover (see page 11). 2. Take off the rear cover (see page 12). 3. Pull out 4 connectors D, E, F and G. 4. Remove the 3 screws A. 5. Take off the c-board case unit B. To attach: 6. Reverse this procedure. To change the fuse 1. After removing the c-board case unit B, remove the 5 screws H, I, J, K and L to pull out the c-board C. 2. Replace the fuse M in the fuse holder N on c-board. If fuse F1 (125V-2.5A) is blown Transformer or C-board is damaged. If fuse F2 (250V-3.15A) is blown Too much power is on the DC motor when the uppershaft, lower shaft or hook race has heavy torque.
PDFMAILER.DE
TRANSFORMER
26
To remove: 1. Remove the front cover (see page 11). 2. Remove the A-board (see page 28). 3. Remove the C-board case (see page 25). 4. Detach the connectors A and B. 5. Remove the screws C and D. 6. Take out the transformer F. To attach: 1. Set the rear side of the transformer F on the supporter E. 2. Tighten the screws C and D. 3. Reconnect connectors A and B. 4. Replace C-board case unit, A-board and the front cover.
PDFMAILER.DE
27
RECEPTACLE
To remove: 1. Remove the front cover and the rear cover (see page 11 and 12). 2. Remove the C-Board case unit C (see page 25). Move it so that the connectors can be pulled out. 3. Pull out connectors A and B. 4. Remove the 2 screws E. To attach: 1. Reverse this procedure.
PDFMAILER.DE
A BOARD
28
To remove: 1. Remove the front cover (see page 11). 2. Pull out the 8 connectors A, B, C, D, E, F, G and H. 3. Remove the 3 screws J. 4. Take off the A-Board. 5. Install a new A-Board and reverse this procedure.
PDFMAILER.DE
29
K AND F BOARD
To remove: 1. Remove the front cover (see page 11). 2. Remove the 7 screws for the printed circuit board F and 2 screws for the printed circuit board K. 3. Pull out the connectors of the printed circuit boards F or K, and then remove the printed circuit boards F or K.
To attach: 1. Insert the connectors of the printed circuit boards F or K. 2. Insert the lever into the groove B of speed control lever A as shown below. 3. Attach the printed circuit board K with the 7 screws, and then attach the printed circuit board F with the 2 screws. 4. Attach the front cover.
PDFMAILER.DE
DC MOTOR
30
To remove: 1. Remove the front cover (see page 11). Move the front cover so that you can pull out the driving motor connector. 2. Remove the receptacle (See page 27). 3. Remove the belt. 4. Removes screw A and remove cord guide B. 5. Pull out the motor connector from the A-board. 6. Remove screws C and D. 7. Take out the motor. To attach: 1. Set the motor in machine and replace screws C and D. 2. Snap the motor connector into the a-board. 3. Attach cord guide B using screw A. 4. Replace the motor belt. 5. Move the motor mounting bracket E by applying approximately 300 g pressure in the middle of the belt, it should deflect 7 to 9 mm when set properly. 6. Tighten screw C and D. 7. Replace the front cover.
PDFMAILER.DE
31
BUTTONHOLE SENSOR
To remove: 1. Remove the front cover (see page 11). Move it so that the connectors can be pulled out. 2. Remove the screw A, then remove the buttonhole sensor B from the sensor plate C. 3. Pull out the connector of buttonhole sensor D from the k-board. 4. Pull out the cord of buttonhole sensor from the cord guide E and then remove the buttonhole sensor B. To attach: 1. Attach the buttonhole sensor B with screw A. Pull the sensor forward so that it touches the setting plate. Make sure it doesn't touch the buttonhole shield plate F, see illustration. 2. Pass the cord as illustrated and attach the front cover. After replacing the buttonhole sensor, sew a few buttonholes. If something is abnormal, adjust the "Buttonhole lever" (see page 22).
PDFMAILER.DE
UPPER SHAFT SENSOR
32
To remove: 1. Remove the front cover (see page 11). 2. Pull out the 8 connectors from the A-board. 3. Remove the 3 screws A and remove the A circuit board E. 4. Push the holders B and remove the upper shaft sensor C. To attach: 1. Attach the new upper shaft sensor C unit into the setting plate. After replacing the upper shaft sensor unit, make sure it doesn't touch the upper shaft shield plate D. 2. Attach the front cover.
PDFMAILER.DE
33
ZIGZAG STEPPING MOTOR
To remove: 1. Remove the C-board case unit and receptacle unit (see page 25 and 27). 2. Remove the 3 screws A and the A-board setting plate. 3. Remove the 2 screws B, 2 screws C and remove the motor D. To attach: 1. Reverse this procedure.
PDFMAILER.DE
FEED STEPPING MOTOR
To remove: 1. Remove the front cover (see page 11). 2. Remove the receptacle unit (see page 27). 3. Pull out the feed stepping motor connector from the A-circuit board. 4. Remove the snap ring B and the 2 screws A. 5. Remove the feed stepping motor C together with feed rod D.
34
To attach: 1. Slide the feed rod D onto the feed arm pin F. 2. Then attach the feed stepping motor by tightening the 2 screws A, tighten the 2 screws at the spot that where the feed arm moves smoothly. 3. Attach the snap ring B. 4. Attach the receptacle and the front cover. 5. Adjust the Stretch stitch feed balance (see page 20).