Text preview for : Bose-901-I&II equal.pdf part of Bose 901I & II equalizer
Back to : Bose-901-I&II equal.pdf | Home
® ®
©1998 Bose Corporation
Service Manual
Contents
Safety Information ............................................................................................................................ 3 Specifications ................................................................................................................................... 4 Technical Description ................................................................................................................... 5-6 Figure 1. Equalizer Controls Response Charts ................................................................................ 6 Disassemble/Assembly Procedure ............................................................................................. 7-8 Figure 2. Staple Location ................................................................................................................. 7 Figure 3. Staple Removal Tool ......................................................................................................... 7 Figure 4. Wiring Diagram ................................................................................................................. 7 Figure 5. Top Cover .......................................................................................................................... 9 Figure 6. Front Panel Assembly ....................................................................................................... 9 Figure 7. Indicator Lens Assembly ................................................................................................... 9 Test Procedure .......................................................................................................................... 10-11 Figure 8. Test Set-Up ..................................................................................................................... 10 Part List ........................................................................................................................................... 12 Part List Notes ................................................................................................................................ 12 Figure 9. 901 I Schematic Diagram................................................................................................ 13 Figure 10. 901 II Schematic Diagram ............................................................................................. 14 Figure 11. 901 Schematic Diagram (first production run) ............................................................... 15
PROPRIETARY INFORMATION THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF BOSE® CORPORATION WHICH IS BEING FURNISHED ONLY FOR THE PURPOSE OF SERVICING THE IDENTIFIED BOSE PRODUCT BY AN AUTHORIZED BOSE SERVICE CENTER OR OWNER OF THE BOSE PRODUCT, AND SHALL NOT BE REPRODUCED OR USED FOR ANY OTHER PURPOSE.
2
SAFETY INFORMATION
1. Parts that have special safety characteristics are identified by the symbol on schematics or by special notes on the parts list. Use only replacement parts that have critical characteristics recommended by the manufacturer. 2. Make leakage current or resistance measurements to determine that exposed parts are acceptably insulated from the supply circuit before returning the unit to the customer. Use the following checks to perform these measurements: A. Leakage Current Hot Check-With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 "Leakage Current for Appliances" and Underwriters Laboratories (UL) 1492 (71). With the unit AC switch first in the ON position, then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the unit (antennas, handle bracket, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milliamp. Reverse the unit power cord plug in the outlet and repeat test. ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE UNIT TO THE CUSTOMER. B. Insulation Resistance Test Cold Check-(1) Unplug the power supply and connect a jumper wire between the two prongs of the plug. (2) Turn on the power switch of the unit. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and each exposed metallic cabinet part on the unit. When the exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 Megohms. When there is no return path to the chassis, the reading must be "infinite". If it is not within the limits specified, there is the possibility of a shock hazard, and the unit must be repaired and rechecked before it is returned to the customer.
CAUTION: THE BOSE® 901 I and II EQUALIZERS CONTAIN NO USER-SERVICEABLE PARTS. TO PREVENT WARRANTY INFRACTIONS, REFER SERVICE TO WARRANTY SERVICE STATIONS OR FACTORY SERVICE.
3
SPECIFICATIONS
901 Series I and II Speaker
Dimensions: Weight: Nominal Impedance: 20-9/16" W x 12-3/4" H x 12-7/8" D 33 lbs 8 ohms
Percentages of Direct and Reflected Sound Radiation
Power radiated by reflection: Power radiated directly: Power Handling: 89% 11% Continuous sine wave @ any frequency: Minimum amplifier power: Peak power (less than 5 seconds): Maximum amplifier power: 50 Watts 25 Watts 400 Watts 270 Watts rms @8 ohms
Damping Factor:
Any amplifier with a damping factor of 40 or higher (must follow the speaker wire recommendation in the Owner's Guide) Nominal driver diameter: Maximum driver excursion: Nominal driver impedance: Weight of each ceramic magnet: 4-1/2" ± 1/4" 8 ohms 9.6 ounces
Driver Complement:
901 Active Equalizer
Dimensions: Input Impedance: Output Impedance: Minimum Load Impedance: Maximum Output Voltage: Maximum Gain: 2-13/16" H x 9-1/4" W x 6-3/4" D 150k ohms Less than 100 ohms
5k ohms
4.0 Volts 18 dB @ 35 Hz
4
TECHNICAL DESCRIPTION
The Bose® 901 speakers represent a fundamental advance in realistic home music reproduction. The unique acoustic design of the speakers provide sound distribution in accurate simulation of live sound. The Active Equalizer provides unprecedented accuracy and control of frequency response characteristics. Each speaker contains nine high compliance, full range speakers with high energy magnets to allow large excursions without audible distortion on any program material. The speakers are acoustically coupled to eliminate audible resonances. The 901 speakers can be used with any high quality amplifier. Its efficiency enables operation with moderately powered amplifiers, yet it can be used with the highest powered amplifiers to reproduce undistorted orchestral peaks at high volume levels. The Bose 901 Active Equalizer is a highly sophisticated electronic console containing ten transistors and more than a hundred components to equalize accurately the stereo response for the effects of radiation impedances, speaker characteristics, enclosure dimensions and even for the presence of the fashion fabric grille cloth. This equalization to flat power radiation is achieved with absolutely no audible distortion of any music or speech signals. Active equalization of the signal before the power amplifier is far superior to passive equalization after the amplifier because it avoids the need to handle high power and does not require the iron-core inductors that introduce distortion in passive equalizers. In addition, it is feasible to use many more elements in an active network to provide much greater accuracy in equalization than is practical in the passive network. The Active Equalizer does much more than just equalize. In addition to providing the flat acoustic output of the Bose 901, the Active Equalizer offers the choice of nineteen additional contours that can be selected from the front panel. This gives the listener the flexibility to exercise his own taste in compensating for recording techniques, listening room characteristics and the other variables described above. As an example of what is possible through active equalization, the equalizer panel contains a switch marked "BELOW 40", which reduces turntable rumble and other low frequency disturbances through a unique filter design that provides a uniform attenuation below 40 Hz while causing no audible deviations above 50 Hz. The rumble is removed without removing the life of the bass along with it.
5
TECHNICAL DESCRIPTION
Figure 1. Equalizer Controls Response Charts 6
DISASSEMBLE/ASSEMBLY PROCEDURE
1. Grille Removal 901 Speaker Disassembly/Assembly 3. Driver Removal 3.1 Perform procedure 1. 3.2 Remove the screws that secure the defective driver. 3.3 Lift the driver out of the cabinet and cut the speaker wire as close to the driver terminals as possible. 4. Driver Replacement 4.1 Connect the speaker wires to the new driver. Refer to Figure 4 for the wire diagram. 4.2 Place the new driver and gasket into the cabinet and secure it in place. 4.3 Perform procedure 2.
1.1 Locate the staples that secure the front or rear grille assembly. Refer to Figures 2 and 3 for the staple placement and tool for removing the staples. 1.2 When removing the front grille assembly, note the placement of the cut out in the grille backing. 2. Grille Replacement 2.1 Place the front grille assembly over the front of the speaker. Note the cut out in the grille backing, be sure to align the cut out with the driver ( on late versions the front grille assembly had two cut outs so the grille placement would not be a factor when reassembling the speaker). Secure using new staples or small finishing nails. 2.2 Place the rear grille assembly on to the speaker and secure using new staples or small finishing nails.
Figure 2. Staple Location
Flat Blade Screwdriver
Machined to a Hook
Figure 3. Staple Removal Tool 7
Figure 4. Wiring Diagram
DISASSEMBLE/ASSEMBLY PROCEDURE
901 EQ Disassembly/Assembly 5. PCB Removal Note: Refer to figures 5 and 6 for the following procedures. 5.1 Perform procedure 1. 1. Top Cover Removal 5.2 Remove the four screws that secure 1.1 Turn the unit over (top down) and the PCB to the chassis and lift the PCB out. remove the four screws located at each of 6. PCB Replacement the corners. 1.2 Flip the unit back over and remove the top cover. 2. Top Cover Replacement 2.1 Align the top cover with the front panel (there is a groove in the top cover for the front panel to slide into). 2.2 Flip the unit over and secure the top cover using the screws that had been removed. 3. Front Panel Removal Note: The series II EQ has a red indicator lens. Refer to Figure 7. for removal. 3.1 Perform procedure 1. 3.2 Remove the treble control knob using an Allen Wrench to loosen the set screw. 3.3 Remove the nut holding the treble control to the chassis. 3.4 Remove the small nut on the inside of the chassis that secures the front panel to the chassis. 4. Front Panel Replacement 4.1 Align the front panel screw with the chassis. 4.2 Secure the front panel to the chassis. 4.3 Secure the treble control to the chassis and replace the control knob. 4.4 Perform procedure 2. 6.1 Place the PCB into the chassis and secure it to the chassis. 6.2 Perform procedure 2. 7. Treble Control Removal 7.1 Perform procedure 3. 7.2 Remove the wires form the control, make note of the placement of the wires. 8. Treble Control Replacement 8.1 Solder the wires onto the control. 8.2 Place the control into the chassis and secure it in place. 8.3 Perform procedure 4. 9. Switch Removal 9.1 Perform procedure 3. 9.2 Remove the wires from the switch, make note of the placement of the wires. 9.3 Remove the rivets that secure the switch to the chassis, using a drill. 10. Switch Replacement 10.1 Secure the new switch to the chassis using rivets or screws. 10.2 Solder the wires to the switch. 10.3 Perform procedure 4.
8
Figure 5. Top Cover
Figure 6. Front Panel Assembly
Figure 7. Indicator Lens Assembly
901 I EQ
901 II EQ
9
TEST PROCEDURE
901 I and II speaker Test 2.2 Reduce the amplifier output to 10 Volts 1. Rub and Tick Test and continue sweeping the signal from 75 Hz to 15 kHz. Listen for any buzzes, rattles, 1.1 Apply a 10 Hz, 25 Volts rms signal and other extraneous noises. Dress any (with the use of an amplifier) to the speaker wires that might be the cause of the noise. terminals. Refer to Figure 8. No extraneous noises such as rubbing, scraping, or ticking 3. Phase Test should be heard. 2. Sweep Test 2.1 Apply a 25 Volt signal, and slowly sweep the oscillator from 10 Hz to 75 Hz. There should be no loud extraneous noises. If there are any loud buzzes or distortion, replace any defective driver. 3.1 Using a 6 to 12 Volt dc supply. Connect the positive (+) wire to the positive terminal and the negative (-) wire to the negative terminal on the speaker. Check that all drives are in phase, all drivers should move outward. If one or more drivers move inward the wiring should be checked. Refer to Figure 4.
Figure 8. Test Set-Up 901 I and II Equalizer Test 1. Gain Test Note: The switches should be pushed in at the top and the treble contour rotary switch should be on the dot. 1.1 Apply a 200 Hz, 500 mV signal to the input. 1.2 Reference a dB meter to the input signal applied. 1.3 Increase the input voltage to 4.25 Volts for the series I EQ and 5 Volts for the series II. The response should be 18 dB for the series I, and 19 dB for the series II ±3 dB. 10 2. Frequency Response Test 2.1 Apply a 200 Hz, 500 mV signal to the input. 2.2 Reference a dB meter to the output. 2.3 Refer to the frequency response table on the following page for the response test.
TEST PROCEDURE
Frequency Response Table Frequency 20 Hz 20 Hz 60 Hz 60 Hz 1 kHz 5 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 12 kHz 20 kHz Below 40 Switch OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF Treble Decrease Switch OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF Treble Contour normal (dot) normal (dot) normal (dot) normal (dot) normal (dot) normal (dot) normal (dot) normal (dot) number 1 number 2 number 3 number 4 number 5 normal (dot) Response Response Tolerance dB dB dB 901 I 901 II 14.8 dB 19 dB ±3 dB 9 dB 9.5 dB ±3 dB 9.2 dB 9.4 dB ±3 dB 8 dB 7.8 dB ±3 dB .2 dB .1 dB ±3 dB 2.2 dB 4 dB ±3 dB 9 dB 12.3 dB ±3 dB 6.9 dB 8.1 dB ±3 dB 2.7 dB 7 dB ±3 dB 3.2 dB 7.8 dB ±3 dB 7.3 dB --±3 dB --15.6 dB ±3 dB 12.4 dB 18.5 dB ±3 dB 12.9 dB 13.8 dB ±3 dB
11
PART LIST
Item Number ------------901 Speaker Part List Description Part Number Driver 103342 Grille, Front 103514-03 Grille, Rear 103512-03 Grille, Front , Ebony 103514-02 Knurled Nut 100424-1 Fuse Kit (External) 108938-3 901 EQ Part List Description Transformer 110V, 220V Power Switch Rocker Switch Rotary Switch Lens Housing, 110V Indicator Lens Front Panel Line Cord, 110V Line Cord, 220V Knob, Treble Contuor 10k ohm Resistor Transistor Diode Note 4 4 4 4
Reference Designator T1 S5 S1, 3, 4 S2 ------------R1 Q1-5, Q51-57 D1, 2
Part Number 100099 100399 100400 100420 116327 103460 100416-1 111672 113608 103457 102537 102437-2 100259-1
Note 3 3
3 Series II 3 3 for 220V
PART LIST NOTES
1. This part is not normally available from Customer Service. Approval from the Field Service Manager is required before ordering. 2. The individual parts located on the PCB are listed in the Electrical Part List. 3. This part is critical for safety purposes. Failure to use a substitute replacement with the same safety characteristics as the recommended replacement part might create shock, fire, and or other hazards. 4. These parts are no longer available.
12
Figure 9. 901 I Schematic Diagram 13
Figure 10. 901 II Schematic Diagram 14
Figure 11. 901 Schematic Diagram (first production run) 15