Text preview for : Crown-MA3600VZ pwramp.pdf part of Crown MA3600VZ power amplifier
Back to : Crown-MA3600VZ pwramp.pdf | Home
POWER AMPLIFIER
SERVICE MANUAL
Macro-Tech MA-3600VZ
Some models may be exported under the name Amcron®
© 2000 by Crown International, Inc., P.O. Box 1000, Elkhart, Indiana 46515-1000 U.S.A. Telephone: 219-294-8000. Trademark Notice: PIPTM, Grounded BridgeTM, and SmartAmpTM are trademarks and Amcron®, Crown®, Macro-Tech®, IOC®, ODEP® and IQ System® are registered trademarks of Crown International, Inc. Other trademarks are the property of their respective owners.
130366-1 11-00 Rev. A
MA-3600VZ Service Manual
130366-1 Rev. A
The information furnished in this manual does not include all of the details of design, production, or variations of the equipment. Nor does it cover every possible situation which may arise during installation, operation or maintenance. If you need special assistance beyond the scope of this manual, please contact the Crown Technical Support Group. Mail: P.O. Box 1000 Elkhart IN 46515-1000 Shipping: Plant 2 SW 1718 W. Mishawaka Road Elkhart IN 46517 Phone: (800) 342-6939 / (219) 294-8200 FAX: (219) 294-8301
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DISCONNECT POWER CORD BEFORE REMOVING REAR INPUT MODULE TO ACCESS GAIN SWITCH.
AVIS
Ŕ PRÉVENIR LE CHOC ÉLECTRIQUE N'ENLEVEZ PAS LES COUVERTURES. RIEN DES PARTIES UTILES Ŕ L'INTÉRIEUR. DÉBRANCHER LA BORNE AVANT D'OUVRIR LA MODULE EN ARRIČRE.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE!
WARNING
The lightning bolt triangle is used to alert the user to the risk of electric shock.
The exclamation point triangle is used to alert the user to important operating or maintenance instructions.
II
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
Revision History
Revision Number
Rev. A
Date
11-2000
Comments
Initial Printing
©2000 Crown International, Inc.
III
MA-3600VZ Service Manual
130366-1 Rev. A
This page intentionally left blank
IV
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
Table of Contents
1 Introduction............................................................................ 1-1
1.1 Introduction ...........................................................................................1-1 1.2 The Macro-Tech Series Amplifiers ........................................................1-1 1.3 Scope....................................................................................................1-1 1.4 Warranty................................................................................................1-1
2 Specifications ......................................................................... 2-1
2.1 Performance .........................................................................................2-1 2.2 Power ....................................................................................................2-1 2.3 Controls.................................................................................................2-1 2.4 Indicators ..............................................................................................2-1 2.5 Input/Output..........................................................................................2-2 2.6 Protection ..............................................................................................2-2 2.7 Construction..........................................................................................2-2
3 Theory of Operation .................................................................. 3-1
3.1 Overview ...............................................................................................3-1 3.2 Features ................................................................................................3-1 3.3 Front End Operation..............................................................................3-1 3.4 Voltage Amplification ............................................................................3-2 3.5 Grounded Bridge Topology ..................................................................3-2 3.6 Output Device Emulation Protection (ODEP)........................................3-4 3.7 VZ Power...............................................................................................3-4
4 Maintenance .......................................................................... 4-1
4.1 Cautions and Warnings........................................................................ 4-1 4.2 General Information ..............................................................................4-1 4.3 Test Procedures ...................................................................................4-1
5 Parts .................................................................................... 5-1
5.1 General Information .............................................................................5-1 5.2 Ordering and Receiving Parts ............................................................ 5-1 5.3 Mechanical Parts ..................................................................................5-1 5.4 Circuit Board Parts..............................................................................5-19
6 Schematic Diagrams ................................................................ 6-1
©2000 Crown International, Inc.
V
MA-3600VZ Service Manual
130366-1 Rev. A
This Page Intentionally Left Blank
VI
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
1 Introduction
1.1 Introduction
This manual contains complete service information on the Crown® MA-3600VZ power amplifier. It is designed to be used in conjunction with the Reference Manual; however, some important information is duplicated in this Service Manual in case the Reference Manual is not readily available. NOTE: THE INFORMATION IN THIS MANUAL IS INTENDED FOR USE BY AN EXPERIENCED TECHNICIAN ONLY!
feature balanced inputs with bridged and parallel monophonic capability. Specific features vary depending on model.
1.3 Scope
This Service Manual in intended to apply to all versions of the MA-3600VZ amplifier. The Parts Listings include parts specific for the US version and the European version (E17CE). For parts specific only to other versions contact the Crown Technical Support Group for help in finding part numbers.
1.4 Warranty
Each Reference Manual contains basic policies as related to the customer. In addition, it should be stated that this service documentation is meant to be used only by properly trained personnel. Because most Crown products carry a 3-Year Full Warranty (including round trip shipping within the United States), all warranty service should be referred to the Crown Factory or Authorized Warranty Service Center. See the applicable Reference Manual for warranty details. To find the location of the nearest Authorized Warranty Service Center or to obtain instructions for receiving Crown Factory Service, please contact the Crown Technical Support Group (within North America), or your Crown/Amcron Importer (outside North America). If you are an Authorized Warranty Service Center and have questions regarding the warranty of a product, please contact the Field Service Manager or the Technical Support Group.
1.2 The Macro-Tech Series Amplifiers
The Macro-Tech ® series is a complete family of amplifiers designed for pro sound reinforcement. Macro-Tech amplifiers are designed to provide enormous levels of pure, undistorted power in a rugged low-profile package, utilizing Crown's patented Grounded BridgeTM output topology. They also employ Crown's patented ODEP® protection circuitry, which keeps the amplifier working under extreme conditions that would shut down a lesser amplifier. The MA-3600VZ features Crown's PIPTM (Programmable Input Processor) expansion system. The PIP expansion system makes it easy to tailor the amplifier to a specific application. Providing high power amplification from 20 Hz to 20 kHz with minimum distortion, Macro-Tech series amplifiers
Crown Customer Service
Technical Support Group Factory Service Parts Department Mailing Address: P.O. Box 1000, Elkhart IN 46515 Shipping Address: Plant 2 S. W. 1718 W. Mishawaka Rd., Elkhart IN 46517 Phone: (219) 294-8200 Toll Free: (800) 342-6939 Fax: (219) 294-8301 http://www.crownaudio.com
©2000 Crown International, Inc.
Introduction 1-1
MA-3600VZ Service Manual
130366-1 Rev. A
Figure 1.1 MA-3600VZ Front and Rear Views
Introduction 1-2
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
2 Specifications
These specifications apply to 120 VAC units in stereo mode with 8 ohm loads and an input sensitivity of 26 dB unless otherwise specified. 120 VAC, 60 Hz Units: These units are equipped with transformers rated for 120 VAC, 60 Hz power. International Units: These units are equipped with transformers for either 100 VAC, 50/60 Hz, or 230 VAC, 50/60 Hz power.
2.1 Performance
Frequency Response: ±0.1 dB from 20 Hz to 20 kHz at 1 watt. Phase Response: ±10° from 10 Hz to 20 kHz at 1 watt. Signal-to-Noise Ratio: Greater than 105 dB below rated output (20 Hz to 20 kHz, A-weighted); 100 dB below rated output (20 Hz to 20 kHz, no weighting). Harmonic Distortion (THD): At rated output, less than 0.05% from 20 Hz to 1 kHz increasing linearly to less than 0.1% at 20 kHz. IM Distortion (IMD): Less than 0.05% from 368 milliwatts to full rated output. Damping Factor: Greater than 1,000 from 10 Hz to 400 Hz. Crosstalk: See Figure 2.1. Slew Rate: Greater than 30 volts per microsecond. Voltage Gain: (At maximum output) 20:1 ±3% or 26 dB ±0.25 dB at +26 dB sensitivity, and 124.6:1 ±12% or 41.9 dB ±1.0 dB at 0.775 volt sensitivity.
120 VAC International Units: Stereo mode with both channels driven: 1490 watts into 2 ohms. 1300 watts into 4 ohms. 985 watts into 8 ohms. Bridge-Mono mode: 2980 watts into 4 ohms. 2600 watts into 8 ohms. Parallel-Mono Mode 2980 watts into 1 ohm. 2600 watts into 2 ohms. 230 VAC International Units: Stereo mode with both channels driven: 1520 watts into 2 ohms. 1325 watts into 4 ohms. 965 watts into 8 ohms. Bridge-Mono mode: 2800 watts into 4 ohms. 2515 watts into 8 ohms. Parallel-Mono Mode 2910 watts into 1 ohm. 2565 watts into 2 ohms. Load Impedance: Rated for 16, 8, 4, and 2 ohm use only. Safe with all types of loads, even reactive ones. AC Power Requirements: 100 VAC, 50/60 Hz; 120 VAC, 50/60 Hz; and 230 VAC, 50/60 Hz units are available. 230 VAC, 50/60 Hz units can be used with 220 and 240 VAC. All versions draw 90 watts or less at idle. 100 and 120 VAC units can draw up to 30 amps of current; 230 VAC units can draw up to 15 amps. Refer to the back panel for your unit's specifications.
2.2 Power
Output Power: Note: Maximum average watts per channel (unless in Mono mode) at 1 kHz with 0.1% or less THD. 120 VAC, 60 Hz Units: Stereo mode with both channels driven: 1800 watts into 2 ohms. 1565 watts into 4 ohms. 1120 watts into 8 ohms. Bridge-Mono mode: 3505 watts into 4 ohms. 3140 watts into 8 ohms. Parallel-Mono mode: 3555 watts into 1 ohm. 3190 watts into 2 ohms. 100 VAC International Units: Stereo mode with both channels driven: 1460 watts into 2 ohms. 1300 watts into 4 ohms. 980 watts into 8 ohms. Bridge-Mono mode: 2835 watts into 4 ohms. 2625 watts into 8 ohms. Parallel-Mono Mode 2820 watts into 1 ohm. 2585 watts into 2 ohms.
2.3 Controls
Enable: A front panel push button used to turn the amplifier on and off. Level: A 31-position detented rotary attenuator for each channel located on the front panel used to control the output level. Stereo/Mono: A three-position back panel switch used to select Stereo, Bridge-Mono or Parallel-Mono operation. Sensitivity: A three-position switch located inside the PIP compartment used to select one of three input sensitivities for both channels: 0.775 volts or 1.4 volts for standard 1 kHz power or a voltage gain of 26 dB. Input Ground Lift: A two position back panel switch used to isolate the phone jack signal grounds from the chassis (AC) ground. Reset: A back panel button for each channel used to reset the corresponding power supply. 100 and 120 VAC units have 15 amp circuit breakers. 230 VAC units have 7.5 amp circuit breakers.
2.4 Indicators
Enable: This amber indicator is on when the amplifier is switched on to show that the low voltage power supply is operating. Signal / IOC: Two green indicators flash with medium intensity in sync with the amplifier's outputs to show signal pres-
©2000 Crown International, Inc.
Specifications 2-1
MA-3600VZ Service Manual
130366-1 Rev. A
ence. In the unlikely event the output waveform differs from that of the input by 0.05% or more, they flash brightly to indicate distortion. As sensitive distortion indicators they provide proof of performance. Note: It is normal for the Channel 2 IOC indicator to remain on in Parallel-Mono mode. ODEP: Each channel has a multifunction LED (light emitting diode) indicator that shows the channel's energy reserve status. Normally, the LEDs are brightly lit to show that reserve energy is available. An indicator will dim proportionally as the energy reserve for its channel decreases. In the rare event that a channel has no reserve energy, the indicator turns off and ODEP proportionally limits the channel's output drive level so the amplifier can continue safe operation even when conditions are severe.
2.7 Construction
Durable black powder coated steel chassis and aluminum front panel with Lexan overlay; specially designed "flowthrough" ventilation from front to side panels. Cooling: Forced-air with custom heat diffusers and patented circuitry to promote uniform dissipation. Dimensions: 19 inch (48.3 cm) standard rack mount (EIA Std. RS-310-B), 3.5 inch (8.9 cm) height, 16 inch (40.6 cm) depth behind mounting surface and 2.5 inches (6.4 cm) in front of mounting surface (see Figure 2.2). Approximate Weight: Center of gravity is 6 inches (15.2 cm) behind the front mounting surface. 120 VAC, 60 Hz Units: Net weight 55 lbs, 1.5 ounces (25.0 kg); shipping weight 63 lbs, 10 ounces (28.9 kg). 100 VAC International Units: Net weight 54 lbs, 5 ounces (24.7 kg); shipping weight 63 lbs, 0.5 ounces (28.6 kg). 120 VAC International Units: Net weight 55 lbs, 1.5 ounces (25.0 kg); shipping weight 63 lbs, 10 ounces (28.9 kg). 230 VAC International Units: Net weight 53 lbs, 6 ounces (24.2 kg); shipping weight 61 lbs, 15 ounces (28.1 kg).
2.5 Input/Output
Input Connector: Balanced Ľ-inch phone jacks on chassis and internal PIP connector. (Balanced 3-pin XLR connectors are provided on the P.I.P.-FX which is a standard feature.) Input Impedance: Nominally 20 k ohms, balanced. Nominally 10 K ohms, unbalanced. Input Sensitivity: Switchable between 0.775 V (unbalanced) for rated output or a fixed voltage gain of 26 dB. Output Connector: Color-coded dual binding posts (banana jacks). Output Impedance: Less than 10 milliohms in series with less than 2 microhenries. DC Output Offset: (Shorted input) ±10 millivolts. Output Signal; Stereo: Unbalanced, two-channel, Bridge-Mono: Balanced, single-channel. Channel 1 controls are active; Channel 2 controls are inactive and not removed from operation, Parallel-Mono: Unbalanced, single-channel. Channel 1 controls are active; Channel 2 controls are inactive but notremoved from operation.
dB
2.6 Protection
Macro-Tech amplifiers are protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature, chain destruction phenomena, input overload damage and high-frequency blow-ups. They also protect loudspeakers from input/output DC and turn-on/turn-off transients. If unreasonable operating conditions occur, the patented ODEP circuitry proportionally limits the drive level to protect the output devices, particularly in the case of elevated temperature. Transformer overheating results in a temporary shutdown of the offending channel. When it has cooled to a safe temperature, the transformer automatically resets itself. Controlled slew rate voltage amplifiers protect against RF burnouts, and input overload protection is provided by current-limiting resistance at the input. Turn On: The four second turn-on delay prevents dangerous turn-on transients. Turn-on occurs at zero crossing of the AC waveform, so power sequencers are rarely needed with multiple units. Note: The turn-on delay time may be changed. Contact Crown's Technical Support Group for details. Circuit Breaker: Circuit breaker current ratings vary based on the AC operating power.
100
TEF ®
1K FREQUENCY (Hz)
10 K
20 K
Figure 2.1 Typical Crosstalk
Figure 2.2 Dimensions
©2000 Crown International, Inc.
Specifications 2-2
130366-1 Rev. A
MA-3600VZ Service Manual
3 Theory of Operation
3.1 Overview
It should be noted that over time Crown makes improvements and changes to their products for various reasons. This manual is up to date as of the time of writing. For additional information regarding these amplifiers, refer to the applicable Technical Notes provided by Crown for this product. This section of the manual explains the general operation of a Macro-Tech 3600VZ power amplifier. Topics covered include Front End, Grounded Bridge, ODEP, and VZ supply. Due to variations in design from vintage to vintage (and similarities with other Crown products) the theory of operation remains simplified.
front panel and are of the rotary type. Front panel indicators let the user know the status of the low voltage power supply (enable), an ODEP indicator for each channel which shows the reserve energy status, and a SPI/IOC indicator for each channel which indicates signal output and distortion. In general, the packaging of this model is designed for maximum watt/price/weight/size value with user friendly features. For additional details refer to the specification section, or to the applicable Owner's Manual.
3.3 Front End Operation
The front end is comprised of three stages: Balanced Gain Stage (BGS), Variable Gain Stage (VGS), and the Error Amp. Figure 3.1 shows a simplified diagram of a typical front end with voltage amplification stages.
3.2 Features
Macro Tech amplifiers utilize numerous Crown innovations including grounded bridge and ODEP technologies. Cooling techniques make use of the what is essentially air conditioner technology. Air flows bottom to top, and front to side. Air flows a short distance across a wide heatsink. This type of air flow provides significantly better cooling than the "wind tunnel" technology used by many other manufacturers. Output transistors are of the metal can type rather than plastic case. This allows for a significantly higher thermal margin for the given voltage and current ratings. All devices used are tested and graded to ensure maximum reliability. Another electronic technique used is negative feedback. Almost all power amplifiers utilize negative feedback to control gain and provide stability, but Crown uses multiple nested feedback loops for maximum stability and greatly improved damping. Most Crown amplifiers have damping in excess of 1000 in the bass frequency range. This feedback, along with our compensation and ultra-low distortion output topology, makes Crown amplifiers superior. Features specific to the Macro Tech Series' include two seperate power transformers (one for each channel), a full time full speed fan which also serves as the low voltage transformer, slew rate limiting, and audio muting for delay or protective action. This amplifier can operate in either a Bridged or Parallel Mono mode as well as dual (stereo). A sensitivity switch allows selection of input voltage required for rated output. Level controls are mounted on the
©2000 Crown International, Inc.
3.3.1 Balanced Gain Stage (BGS)
Input to the amplifier is balanced. The shield may be isolated from chassis ground by an RC network to interrupt ground loops via the Ground Lift Switch. The non-inverting (hot) side of the balanced input is fed to the non-inverting input of the first op-amp stage. The inverting (negative) side of the balanced input is fed to the inverting input of the first op-amp stage. A potentiometer is provided for common mode rejection adjustment. Electrically, the BGS is at unity gain. (From an audio perspective, however, this stage actually provides +6dB gain if a fully balanced signal is placed on its input.) The BGS is a non-inverting stage. It's output is delivered to the Variable Gain Stage.
3.3.2 Variable Gain Stage (VGS)
From the output of the BGS, the signal goes to the VGS where gain is determined by the position of the Sensitivity Switch, and level is determined by the level control. VGS is an inverting stage with the input being fed to its op-amp stage. Because gain after this stage is fixed at 26dB (factor of 20), greater amplifier sensitivity is achieved by controlling the ratio of feedback to input resistance. The Sensitivity Switch sets the input impedance to this stage and varies the gain such that the overall amplifier gain is 26 dB, or is adjusted appropriately for 0.775V or 1.4V input to attain rated output.
3.3.3 Error Amp
The inverted output from the VGS is fed to the noninverting input of the Error Amp op-amp stage through
Theory of Operation 3-1
MA-3600VZ Service Manual
130366-1 Rev. A
an AC coupling capacitor and input resistor. Amplifier output is fed back via the negative feedback (NFb) loop resistor. The ratio of feedback resistor to input resistor fixes gain from the Error Amp input to the output of the amplifier at 26 dB. Diodes prevent overdriving the Error Amp. Because the Error Amp amplifies the difference between input and output signals, any difference in the two waveforms will produce a near open loop gain condition which in turn results in high peak output voltage. The output of the Error Amp, called the Error Signal (ES) drives the Voltage Translators.
Also tied into the Voltage Translator inputs are ODEP limiting transistors and control/protection transistors. The ODEP transistors steal drive as dictated by the ODEP circuitry (discussed later). The control/protection transistors act as switches to totally shunt audio to ground during the turn-on delay, or during a DC/LF or Fault protective action.
3.4.2 Last Voltage Amplifiers (LVAs)
The Voltage Translator stage channels the signal to the Last Voltage Amplifiers (LVA's) in a balanced configuration. The +LVA and -LVA, with their pushpull effect through the Bias Servo, drive the fully complementary output stage. The LVAs are configured as common emitter amplifiers. This configuration provides sufficient voltage gain and inverts the audio. The polarity inversion is necessary to avoid an overall polarity inversion from input jack to output jack, and it allows the NFb loop to control Error Amp gain by feeding back to its non-inverting input (with its polarity opposite to the output of the VGS). With the added voltage swing provided by the LVAs, the signal then gains current amplification through the Darlington emitter-follower output stage.
3.4 Voltage Amplification
The Voltage Translator stage separates the output of the Error Amp into balanced positive and negative drive voltages for the Last Voltage Amplifiers (LVAs), translating the signal from ground referenced ±15V to ±Vcc reference. LVAs provide the main voltage amplification and drive the High Side output stages. Gain from Voltage Translator input to amplifier output is a factor of 25.2.
3.4.1 Voltage Translators
A voltage divider network splits the Error Signal (ES) into positive and negative drive signals for the balanced voltage translator stage. These offset reference voltages drive the input to the Voltage Translator transistors. A nested NFb loop from the output of the amplifier mixes with the inverted signal riding on the offset references. This negative feedback fixes gain at the offset reference points (and the output of the Error Amp) at a factor of -25.2 with respect to the amplifier output. The Voltage Translators are arranged in a common base configuration for non-inverting voltage gain with equal gain. They shift the audio from the ±15V reference to VCC reference. Their outputs drive their respective LVA.
3.5 Grounded Bridge Topology
Figure 3.2 is a simplified example of the grounded bridge output topology. It consists of four quadrants of three deep Darlington (composite) emitter-follower stages per channel: one NPN and one PNP on the High Side of the bridge (driving the load), and one NPN and one PNP on the Low Side of the bridge (controlling the ground reference for the rails). The output stages are biased to operate class AB+B for ultra low distortion in the signal zero-crossing region and high efficiency.
+15V
BGS
VGS
Voltage Divider
Error Amp
Voltage Translators
Q100 Q121 Q101 Q102 Q103 Q122
+VCC
Q105
Audio Inputs
+ -
+ -
+ -
NPN Outputs (+HS) PNP Outputs (-HS)
Q110
-15V
ODEP
-+
Mute NFb Loop
-VCC
LVA's
Figure 3.1 Typical Amplifier Front End and Voltage Amplification Stages. Theory of Operation 3-2
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
3.5.1 High Side (HS)
The High Side (HS) of the bridge operates much like a conventional bipolar push-pull output configuration. As the input drive voltage becomes more positive, the HS NPN conducts and delivers positive voltage to the load. Eventually the NPN devices reach full conduction and +Vcc is across the load. At this time the HS PNP is biased off. When the drive signal is negative going, the HS PNP conducts to deliver -Vcc to the load and the HS NPN stage is off. The output of the +LVA drives the base of predriver device. Together, the predriver and driver form the first two parts of the three-deep Darlington and are biased class AB. They provide output drive through the bias resistor, bypassing the output devices, at levels below about 100mW. An RLC network between the predriver and driver provide phase shift compensation and limit driver base current to safe levels. Output devices are biased class B, just below cutoff. At about 100mW output they switch on to conduct high current to the load. Together with predriver and driver, the output device provide an overall class AB+B output. The negative half of the HS is almost identical to the positive half, except that the devices are PNP. One difference is that the PNP bias resistor is slightly greater in value so that PNP output devices run closer to the cutoff level under static (no signal) conditions. This is because PNP devices require greater drive current.
HS bias is regulated by Q18, the Bias Servo. Q18 is a Vbe multiplier which maintains approximately 3.3V Vce under static conditions. The positive and negative halves of the HS output are in parallel with this 3.3V. With a full base-emitter on voltage drop across predrivers and drivers, the balance of voltage results in approximately .35V drop across the bias resistors in the positive half, and about .5V across the bias resistor in the negative half. Q18 conduction (and thus bias) is adjustable. A diode string prevents excessive charge build up within the high conduction output devices when off. Flyback diodes shunt back-EMF pulses from reactive loads to the power supply to protect output devices from dangerous reverse voltage levels. An output terminating circuit blocks RF on output lines from entering the amplifier through its output connectors.
3.5.2 Low Side (LS)
The Low Side (LS) operates quite differently. The power supply bridge rectifier is not ground referenced, nor is the secondary of the main transformer. In other words, the high voltage power supply floats with respect to ground, but ±Vcc remain constant with respect to each other. This allows the power supply to deliver +Vcc and -Vcc from the same bridge rectifier and filter as a total difference in potential, regardless of their voltages with respect to ground. The LS uses inverted feedback from the HS output to control the ground reference for the rails (±Vcc). Both LS quadrants are arranged in a three-deep Darlington
+
+Vcc (Positive Rail)
Input signal
Load (speaker)
Inverting Op-amp LOW SIDE
HIGH SIDE
-Vcc (Negative Rail)
Figure 3.2 Grounded Bridge Output Topology
©2000 Crown International, Inc.
Theory of Operation 3-3
MA-3600VZ Service Manual
130366-1 Rev. A
and are biased AB+B in the same manner as the HS. When the amplifier output swings positive, the audio is fed to an op-amp stage where it is inverted. This inverted signal is delivered directly to the bases of the positive (NPN) and negative (PNP) LS predrivers. The negative drive forces the LS PNP devices on (NPN off). As the PNP devices conduct, Vce of the PNP Darlington drops. With LS device emitters tied to ground, -Vcc is pulled toward ground reference. Since the power supply is not ground referenced (and the total voltage from +Vcc to -Vcc is constant) +Vcc is forced higher above ground potential. This continues until, at the positive amplifier output peak, -Vcc = 0V and +Vcc equals the total power supply potential with a positive polarity. If, for example, the power supply produced a total of 70V from rail to rail (±35VDC measured from ground with no signal), the amplifier output would reach a positive peak of +70V. Conversely, during a negative swing of the HS output where HS PNP devices conduct, the op-amp would output a positive voltage forcing LS NPN devices to conduct. This would result in +Vcc swinging toward ground potential and -Vcc further from ground potential. At the negative amplifier output peak, +Vcc = 0V and -Vcc equals the total power supply potential with a negative polarity. Using the same example as above, a 70V supply would allow a negative output peak of -70V. In summary, a power supply which produces a total of 70VDC rail to rail (or ±35VDC statically) is capable of producing 140V peak-topeak at the amplifier output when the grounded bridge topology is used. The voltage used in this example are relatively close to the voltages of the PB-1/460CSL. The total effect is to deliver a peak to peak voltage to the speaker load which is twice the voltage produced by the power supply. Benefits include full utilization of the power supply (it conducts current during both halves of the output signal; conventional designs require two power supplies per channel, one positive and one negative), and never exposing any output device to more than half of the peak to peak output voltage (which does occur in conventional designs). Low side bias is established by a diode string which also shunts built up charges on the output devices. Bias is adjustable via potentiometer. Flyback diodes perform the same function as the HS flybacks. The output of the LS is tied directly to chassis ground via ground strap. Theory of Operation 3-4
3.6 Output Device Emulation Protection (ODEP)
To further protect the output stages, a specially developed ODEP circuit is used. It produces a complex analog output signal. This signal is proportional to the always changing safe-operatingarea margin of the output transistors. The ODEP signal controls the Voltage Translator stage by removing drive that may exceed the safe-operating-area of the output stage. ODEP senses output current by measuring the voltage dropped across LS emitter resistors. LS NPN current (negative amplifier output) and +Vcc are sensed, then multiplied to obtain a signal proportional to output power. Positive and negative ODEP voltages are adjustable via two potentiometers. Across ±ODEP are a PTC and a thermal sense (current source). The PTC is essentially a cutoff switch that causes hard ODEP limiting if heatsink temperature exceeds a safe maximum, regardless of signal level. The thermal sense causes the differential between +ODEP and ODEP to decrease as heatsink temperature increases. An increase in positive output signal output into a load will result in ODEP voltage dropping; an increase in negative output voltage and current will cause +ODEP voltage to drop. A complex RC network between the ±ODEP circuitry is used to simulate the thermal barriers between the interior of the output device die (immeasurable by normal means) and the time delay from heat generation at the die until heat dissipates to the thermal sensor. The combined effects of thermal history and instantaneous dynamic power level result in an accurate simulation of the actual thermal condition of the output transistors.
3.7 VZ Power
VZ means Variable Impedance and is the name of Crown's patented articulated power supply technology. It enables Crown to pack tremendous power into just 3˝ inches of vertical rack space.
3.7.1 Background
A power supply must be large enough to handle the maximum voltage and current necessary for the amplifier to drive its maximum rated power into a specified load. In the process of fulfilling this requirement conventional power supply designs produce excessive heat, are heavy, and take up precious real estate. It's no secret that heat is one of a power amplifiers worst enemies.
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
According to Ohm's Law, the bigger the power supply, the more heat the power transistors must dissipate. Also, the lower the resistance of the power transistors, the more voltage you can deliver to the load. But at the same time that you lower the resistance of the transistors, you increase the current passing through them, and again increase the amount of heat they must dissipate.
VZ POWER SUPPLY
+
POWER TRANSISTOR
VZ STAGE
SPEAKER LOAD
+
VZ STAGE
3.7.2 The VZ supply
An articulated power supply, like VZ, can circumvent much of this problem by reducing the voltage applied to the transistors when less voltage is required. Reducing the voltage reduces the heat. Since the amplifier runs cooler, you can safely pack more power into the chassis. The VZ supply is divided into segments to better match the voltage and current requirements of the power transistors. Remember that audio signals like music are complex waveforms. For music the average level is always much less than the peak level. This means a power supply does not need to produce full voltage all the time. The VZ supply is divided into two parts. When the voltage requirements are not high, it operates in a parallel mode to produce less voltage and more current (Figure 3.3). In this mode the power transistors stay cooler and are not forced to needlessly dissipate heat. This is the normal operating mode of the VZ power supply.
VZ POWER SUPPLY
POWER TRANSISTOR
Figure 3.4 VZ Supply in Series Mode
Sensing circuitry watches the voltage of the signal to determine when to switch modes. The switching circuitry is designed to prevent audible switching distortion to yield the highest dynamic transfer function--you hear only the music and not the amplifier. You get not only the maximum power with the maximum safety, you also get the best power matching to your load.
3.7.3 VZ Switch Control
The two halves of U03 form identical comparators that monitor the available voltage of DC supply V2 and compare it to the output voltage of the amplifier. When a positive going output voltage exceeds a predetermined ratio of the available supply voltage, U03 pin 1 produces a low voltage triggering U04. When triggered, the "Q" output of U04 changes from low to high driving the gates of FET's Q00, Q01, and Q02. The other half of U03 (pin 7) reacts to negative going output voltage. Both halves of U03 receive V2 and amplifier output voltage differentially. The time constant set by C18 and R16 on the input of U04 sets the maximum switch frequency of the supply. This time constant forces the supply to stay in the series mode regardless of amplifier condition for 200 ms. The reset pin of U04 (pin 4) forces the output of U04 low when FET damage conditions exist. C16 and C17 provide hysteresis around the comparators of U03 to insure stable operation. VZ Protection Circuit Protecting high current transistors can be troublesome in circuits that do not provide convenient current sample points. FETs Q00-Q02 fall into this class of problems, but protection has been designed based on the following two conditions being present at the same time:
POWER TRANSISTOR
+
SPEAKER LOAD
VZ STAGE
+
VZ STAGE
POWER TRANSISTOR
Figure 3.3 VZ Supply in Parallel Mode
When the voltage requirements are high the VZ supply switches to a series mode to produce the higher voltage and less current (Figure 3.4). The amplified output signal never misses a beat and gets full voltage when it needs it--not when it doesn't need it.
©2000 Crown International, Inc.
Theory of Operation 3-5
MA-3600VZ Service Manual
130366-1 Rev. A
· Higher than normal on-state drain to source voltage · Gate drive present. When both of these conditions exist, a reasonable assumption can be made that the FETs are operating in an area that if sustained will cause damage to the FETs. These two conditions are detected by U05 pins 5 and 7. U05 detects gate drive to the FETs at pin 7. Pin 6 is a reference input with the reference voltage set by R22 in series with R19. U05 detects excessive source to drain voltage on the
FETs at pin 5. R17 in series with R18 forms a voltage divider to pin 5 of U05. The reference is set by a voltage divider formed by R29, R20, and R22. When both conditions are detected the outputs of U05 (pins 1 and 2) allow C20 to start charging through R23. After 20µS, C20 will be sufficiently charged to turn on the section of U05 whose output is pin 14, discharging C21. As C21 discharges, it turns on Q03 which pulls the non-inverting input low (pin 9). U05 pin 13 drives the reset pin of U04 low which removes gate drive from the FETs. This hysteresis makes the circuit auto-resetting. Every 10ms (set by C21 and R26) it will make another 20µs try at driving the FETs. R25 prevents Q03 from pulling the input of U05 below its negative supply.
+VCC DISPLAY PANEL POSITIVE HIGH SIDE OUTPUT STAGE NPN
VOLTAGE TRANSLATOR
LVA
BALANCED INPUTS
XLR
P.I.P. FX
A (ODEP) ODEP B (ODEP) BALANCE GAIN STAGE VARIABLE GAIN STAGE ERROR AMP
BIAS SERVO
CURRENT LIMIT OUTPUT
1/4" PHONE
VOLTAGE TRANSLATOR
LVA
NEGATIVE HIGH SIDE OUTPUT STAGE PNP -VCC
NFb +VCC A (ODEP)
POSITIVE LOW SIDE OUTPUT STAGE NPN
-1
BIAS NETWORK
INVERTING BRIDGE BALANCE NEGATIVE LOW SIDE OUTPUT STAGE PNP -VCC B (ODEP)
Figure 3.5 Typical Crown Grounded Bridge Amplifier Basic Block Diagram (One Channel Shown)
Theory of Operation 3-6
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
4 Maintenance
4.1 Cautions and Warnings
DANGER: The outputs of this amplifier can produce LETHAL energy levels! Be very careful when making connections. Do not attempt to change output wiring until the amplifier has been off at least 10 seconds. WARNING: This unit is capable of producing high sound pressure levels. Continued exposure to high sound pressure levels can cause permanent hearing impairment or loss. User caution is advised and ear protection is recommended when using at high levels. WARNING: Do not expose this unit to rain or moisture. WARNING: Only properly trained and qualified technicians should attempt to service this unit. There are no user serviceable parts inside. WARNING: When performing service checks with the power off, discharge the main power supply filter capacitors fully before taking any measurements or touching any electrical components. A 300-ohm 10-W resistor is recommended for this. Hold the resistor with pliers, as the resistor may become extremely hot. WARNING: Under load, with a sine wave signal at full power into both channels, the amplifier may draw in excess of 30 amperes from the AC service mains. WARNING: Do not change the position of the Mode Switch when the amplifier is turned on. If the position of this switch is changed while the amplifier is powered, transients may damage your speakers. WARNING: Heatsinks are not at ground potential. Simultaneously touching either heatsink and ground, or both heatsinks will cause electrical shock. CAUTION: Eye protection should be worn at all times when protective covers are removed and the amplifier is plugged in. CAUTION: Disconnect the power cord before installing or removing any cover or panel.
All tests assume that AC power is from a regulated AC source appropriate for the unit under test.. Test equipment includes an oscilloscope, a DMM, a signal generator, loads, and I.M.D. and T.H.D. noise test equipment.
4.3 Test Procedures
4.3.1 Standard Initial Conditions
Level controls fully clockwise. Stereo/Mono switch in Stereo. Sensitivity switch in 26 dB fixed gain position. Ambient Temperature: 20 to 30 degrees C. It is assumed, in each step, that conditions of the amplifier are per these initial conditions unless otherwise specified.
4.3.2 Test 1: DC Offset
Spec: 0 VDC, ±5 mV. Initial Conditions: Controls per standard, inputs shorted. Procedure: Measure DC voltage at the output connectors (rear panel). There is no adjustment for output offset. If spec is not met, there is an electrical malfunction. Slightly out of spec measurement is usually due to U104/U204 out of tolorance.
4.3.3 Test 2: Output Bias Adjustment
Spec: 310 ±10 mVDC. Initial Conditions: Controls per standard, heatsink temperature less than 40°C. Procedure: Measure DC voltages on the output PWA across R02, adjust R26 if necessary. Measure DC voltages on the output PWA across R21, adjust R23 if necessary. Repeat for second channel.
4.3.4 Test 3: ODEP Voltage Adjustment
Spec: Bias Per Chart, ±0.1V DC. Initial Conditions: Controls per standard, heatsink at room temperature 20 to 30°C (68 to 86°F). Note: This adjustment should normally be performed within 2 minutes of turn on from ambient (cold) conditions. If possible measure heatsink temperature, if not measure ambient room temperature. Use this information when referencing the chart on the following page.
4.2 General Information
The following test procedures are to be used to verify operation of this amplifier. DO NOT connect a load or inject a signal unless directed to do so by the procedure. These tests, though meant for verification and alignment of the amplifier, may also be very helpful in troubleshooting. For best results, tests should be performed in order.
©2000 Crown International, Inc.
Mantenance 4-1
MA-3600VZ Service Manual
130366-1 Rev. A
°F 66 68 70 72 74 76 77 78 80 82 84 86 88 90 92 94
°CV 18.9 20.0 21.1 22.2 23.3 24.4 25.0 25.6 26.7 27.8 28.9 30.0 31.1 32.2 33.3 34.4
ODEPV 11.31 11.26 11.20 11.14 11.09 11.03 11.00 10.97 10.91 10.86 10.80 10.74 10.69 10.63 10.57 10.51
+ODEP 11.31 11.26 11.20 11.14 11.09 11.03 11.00 10.97 10.91 10.86 10.80 10.74 10.69 10.63 10.57 10.51
4.3.6 Test 5: Common Mode Rejection
Spec at 1KHz: 70 dB. Initial Conditions: Sensitivity switch in 0.775V Procedure: No load. Inject a 0 dBu (.775VRMS) 1K Hz sine wave into each channel, one channel at a time, with inverting and non-inverting inputs shorted together (common mode). Adjust R512 for minimum A.C output of Channel 1, R612 for Channel 2. At the output measure less than 28 dBu (30.5mVRMS).
4.3.7 Test 6: Voltage Gain
Spec 26dB Gain: Gain of 20.0 ±3%. Spec 0.775V Sensitivity: ±12%. Spec 1.4V Sensitivity: ±12%. Initial Conditions: Controls per standard. Procedure: 8 ohm load connected. Inject a single ended 0.775 VAC 1 kHz sine wave with the Sensitivity Switch in the 26 dB position. Measure 15.5 VAC, ±0.3 VAC, at the amplifier output. Switch the Sensitivity Switch to the 0.775V position. Adjust the level of the input signal so that the output is at rated power. Measure 0.775 VAC ±12% at the amplifier input. Switch the sensitivity switch to the 1.4V position Measure 1.4 VAC, ±12%, at the amplifier input.
ODEP Procedure: Measure pin 6 of U100 and, if necessary, adjust R121 to obtain VODEP as specified above. Measure pin 6 of U200 and, if necessary, adjust R221 to obtain VODEP as specified above. +ODEP Procedure: Measure pin 6 of U103 and, if necessary, adjust R132 to obtain V+ODEP as specified above. Measure pin 6 of U203 and, if necessary, adjust R232 to obtain V+ODEP as specified above.
4.3.8 Test 7: Phase Response
Spec: ±10° from 10 Hz to 20 kHz at 1 Watt. Initial Conditions: Controls per standard, 8 ohm load on each channel. Procedure: Inject a 1 kHz sine wave and adjust for 1 Watt output (2.8 VAC). Check input and output signals against each other, input and output signals must be within 10° of each other.
4.3.5 Test 4: AC Power Draw
Spec: 100 Watts maximum quiescent. Initial Conditions: Controls per standard. Procedure: With no input signal and no load, measure AC line wattage draw. If current draw is excessive, check for high AC line voltage or high bias voltage.
IN 1k ohm .047µf
OUT
Figure 4.1 Differentiator Circuit Figure 4.2 Differentiated wave form at current limit Mantenance 4-2
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
4.3.9 Test 8: Level Controls
Spec: Level controlled by level controls. Initial Conditions: Controls per standard. Procedure: No Load. Inject a 1 kHz sine wave. With level controls fully clockwise you should see full gain. As controls are rotated counterclockwise, observe similar gain reduction in each channel. When complete, return level controls to fully clockwise position.
Procedure: 8 ohm load on each channel. Inject a 20 kHz sine wave into the Channel 1 input and increase output level to 80 VAC. Measure less than 80 mVAC at the output of Channel 2. Inject a 20 kHz sine wave into the Channel 2 input and increase output level to 80 VAC. Measure less than 80 mVAC at the output of Channel 1.
4.3.13 Test 12: Output Power
Spec at 8 Ohm Stereo: 1125W at 0.1% THD. Spec at 4 Ohm Stereo: 1625W at 0.1% THD. Spec at 2 Ohm Stereo: 1800W at 0.1% THD. International 8 Ohm Stereo: 945W at 0.1% THD. International 4 Ohm Stereo: 1255W at 0.1% THD. International 2 Ohm Stereo: 1490W at 0.1% THD. Initial Conditions: Controls per standard. Procedure: Load each channel to 8 ohms. Inject a 1 kHz sine wave and measure at least 94.67 VAC at the output of each channel. Load each channel to 4 ohms. Inject a 1 kHz sine wave and measure at least 80.62 VAC. Load each channel to 2 ohms. Inject a 1 kHz sine wave and measure at least 60.00 VAC. All power measurements must be at less than 0.1% THD. For international units, calculate output voltage with above power specifications.
4.3.10 Test 9: Current Limit
Spec: Current Limit at 43 - 48 Amps Initial Conditions: Controls per standard. Procedure: Load each channel to 1 Ohm. Inject a 1 kHz differentiated (or 10% duty cycle) square wave. See figure 4.1. Increase output level until current limit occurs. Current limit should occur at 43 - 48 Amps (43-48 Vpk). Disregard waveform overshoot. Observe clean (no oscillations) current clipping. See Figure 4.2 for differentiated wave form at current limit.
4.3.11 Test 10: Slew Rate & 10 kHz Square Wave
Spec: 30 - 40 V/µS. Initial Conditions: Controls per standard. Procedure: Load each channel to 8 ohms. Inject a 10 kHz square wave to obtain 90 volts zero-to-peak at each output. Observe the slope of the square wave. It should typically measure 30 to 40 V/µS. Also, the square wave must not include overshoot, ringing, or any type of oscillation. See Figure 4.3 for typical 10 kHz square wave response.
4.3.14 Test 13: Reactive Loads
Spec: No oscillations. Safe with all types of loads. Initial Conditions: Controls per standard. Procedure Capacitive: Load each channel to 8 ohms in parallel with 2 µF. Inject a 20 kHz sine wave with 48 VAC output for 10 seconds. Procedure Inductive: Load each channel to 8 ohms in parallel with 159 µHenries. Inject a 1 kHz sine wave with 36 VAC output for 10 seconds.
4.3.12 Test 11: Crosstalk
Spec: -60dB at 20 kHz. Initial Conditions: Controls per standard. Terminate input of channel not driven with 600 ohms.
Figure 4.3 10 kHz square wave response
©2000 Crown International, Inc.
Figure 4.4 ODEP limiting wave form Mantenance 4-3
MA-3600VZ Service Manual
130366-1 Rev. A
Procedure Torture: Load each channel with the primary (red and black leads) of a PSU transformer (D 7040-5). Inject a 35 Hz sine wave for an output level of 89.5 Vrms, for 10 seconds. Procedure Short: Inject a 60 Hz sine wave with 30.0 VAC at the amplilfier output. After establishing signal, short the output for 10 seconds.
4.3.18 Test 17: Turn On Transients
Spec: No dangerous transients. Initial Conditions: Controls per standard. Procedure: From an off condition, turn on the amplifier and monitor the output noise at the time of turn on. Note: Turn on noise may increase significantly if the amplifier is cycled off and on.
4.3.15 Test 14: ODEP Limiting
Spec: ODEP Limiting occurs per the procedure. Either channel controls limiting in Parallel Mono Mode. Initial Conditions: Controls per standard; rag or other obstruction blocking fan so that it does not turn. Procedure: Load the amplifier to 2 ohms on each channel. Inject a 60 Hz sine wave and adjust for 30 Vrms at the output. After a few minutes observe a wave form similar to Figure 4.4. Both positive and negative alternations must show the distinctive waveform. There is no requirement of symmetry between positive and negative alternations. There is no requirement of uniformity from channel to channel. Remove the input signal from both channels and allow the amplifier to cool for a few minutes. Switch the amplifier to Parallel Mono and remove the load from Channel 1. Inject the signal into Channel 1 and observe that ODEP limiting occurs at the output of both channels. Remove the load from Channel 2, and install the load on Channel 1. Again, observe that both channels limit. Return all amplifier controls to standard initial conditions. Remove the fan obstruction.
4.3.19 Test 18: Turn Off Transients
Spec: No dangerous transients. Initial Conditions: Controls per standard. Procedure: From an on condition, turn off the amplifier and monitor the output noise at the time of turn off. Note: Turn off noise may increase significantly if the amplifier is cycled off and on.
4.3.20 Test 19: Intermodulation Distortion
Spec at 0 dB Output: 0.02%. Spec at 35 dB Output: 0.05%. Initial Conditions: Controls per standard. Procedure: Load each channel to 8 ohms. Inject a SMPTE standard IM signal (60 Hz and 7 kHz sine wave mixed at 4:1 ratio). Set the 60 Hz portion of the sine wave to 72 Volt RMS. Set the 7 kHz portion to 25%. With an IM analyzer measure less than 0.02% IMD. Repeat test at 35 dB (reference 72 Volt RMS, 60 Hz portion) and measure less than 0.05% IMD.
4.3.21 Test 20: High Line Cutout
Spec: 10% - 12% above nominal. Initial Conditions: Controls per standard. Procedure: Using an AC line variac, increase the line voltage until the unit goes into standby. The unit should fo into standby at 10% - 12% above the nominal (120V U.S. units).
4.3.16 Test 15: LF Protection
Spec: Amplifier mutes for low frequency. Initial Conditions: Controls per standard. Procedure: No load. Inject a 0.5 Hz, 10 volt peak-topeak, square wave, or a 1Hz, 17 volt peak-to-peak, sine wave into each channel and verify that each channel cycles into mute.
4.3.22 Post Testing
After completion of testing, if all tests are satisfactory, the amplifier controls should be returned to the positions required by customer. If conditions are unknown or unspecified, factory settings are as follows: Level Controls: 9 to 11 O'Clock. Sensitivity Switch: 0.775V U.S., 1.4V International. Stereo/Mono Switch: Stereo. Ground Lift: Lift. Power: Off.
4.3.17 Test 16: Signal to Noise Ratio
Spec: 100 dB below rated 8 ohm power 20 Hz to 20 kHz. 105 dB A-Weighted. Initial Conditions: 26dB Sensitivity. Short inputs. Procedure: Load each channel to 8 ohms. Measure less than 950 µV at the output of each channel (20 Hz-20 kHz bandpass filter).
Mantenance 4-4
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5 Parts
5.1 General Information
Replacement parts for this Crown amplifier can be ordered from the Crown Parts Department. PART PRICES AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.
established, after which an amount due will be issued and shipment made upon receipt of payment. New parts returned for credit are subject to a restocking fee, and authorization from the Crown Parts Department must be obtained before returning parts for credit.
5.2.2 Shipment
Shipment will normally be made via UPS, or best other method unless you specify otherwise. Shipments are made to and from Elkhart, Indiana USA, only. Established accounts with Crown will receive shipment freight prepaid and will be billed. All others will receive shipment on a C.O.D. or prepayment (check or credit card) basis.
5.2 Ordering and Receiving Parts
When ordering parts, be sure to give the product model, and include a description and part number from the parts listing. Price quotes are available on request.
5.3 Mechanical Parts
This section includes a mechanical part list for this product. All serviceable parts and assemblies will have a Crown Part Number (CPN) listed in this chapter. The parts listed are current as of the date printed. Crown reserves the right to modify and improve its products for the benefit of its customers.
5.2.1 Terms
Normal terms are prepaid. Net-30 Days applies to only those having pre-established accounts with Crown. The Crown Parts Department does accept Visa or Master Card. If prepaying, the order must be packed and weighed before a total bill can be
Crown Customer Service
Technical Support Group Factory Service Parts Department Mailing Address: P.O. Box 1000, Elkhart IN 46515 Shipping Address: Plant 2 S. W. 1718 W. Mishawaka Rd., Elkhart IN 46517 Phone: (219) 294-8200 Toll Free: (800) 342-6939 Fax: (219) 294-8301 http://www.crownaudio.com
©2000 Crown International, Inc.
Parts 5-1
MA-3600VZ Service Manual
130366-1 Rev. A
14 13 12 11 10 15 16
25 8
9 17 7 18 19 4 3 2 5 20 21 23 22
6
1
24
Figure 5.1 Top Chassis Assembly
Parts 5-2
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.1 Top Chassis Assembly
Refer to Figure 5.1 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Not Pictured
1 1
Front Assembly Chassis
4 2 2 1 8 8 8 1 1 1 1 1 5 20 1 1 1
Heatsink Assembly Paper Shroud Channel 1 B-L Switch Assembly Power Transformer 120VAC 60Hz Domestic Power Transformer 230VAC 50Hz E17CE Transformer Plate #8 Nylon Shoulder Washer #8 Int Star Washer Screw, 8-32 x 2.75 MSCR PNHD Zinc Fan Assembly Top Cover Back Panel Assembly Fuse, 1A 3AG 1.25 x .25 Control PWA 1/4 PC BD Support star washer Screw, 6-32 x.31 TORX PNHD STAR Channel 2 B-L Switch Assembly Bottom Cover Insulator, 11 x 15 Transformer Cable Tie Mount
see Section 5.3.3 F12621-3 see Section 5.3.3 see Section 5.3.3 see Section 5.3.6 see Section 5.3.8 D 8867-0 see Section 5.3.5 D 8874-6 D8876-1 F12588-4 A10099-5 A10094-6 A10089-10844 see Section 5.3.7 see Section 5.3.7 F12544J6 see Section 5.3.4 A10285-10 see Section 5.4 C 6032-4 included with screw 103433-70605 see Section 5.3.6 F12609-8 D8249-1 C 6918-4
©2000 Crown International, Inc.
Parts 5-3
MA-3600VZ Service Manual
130366-1 Rev. A
9
10 11 7 8 6 5 4 3
6 5 3
2
2
14
13 12
1
Figure 5.2 Bottom Chassis Assembly
Parts 5-4
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.2 Bottom Chassis Assembly
Refer to Figure 5.2 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2
1 2
3 4 5 6 7 8 9 10 11 12 13 14
2 24 4 8 2 2 1 2 2 2 4 2
Chassis Pad, VZ Thru Hole Note: use CPN #D 7679-0 with Output PWB P10316-1 and earlier. Output PWA 6-32 x .312 Pan HD T15 Screw Driver Bracket Screw, 6-32 x.312 Torx Spacer, .75 Plastic Spacer, 1.0 Plastic Main PWA Screw, 8-18 x 1.375 PNHD MSCR Zinc Nylon Washer Board Support, Plastic Slip Collar Sil Pad, 1.12 x 5 60
see Section 5.3.1 D7839-0
See Section 5.4 A10315-1 D8300-2 103415-70605 C6914-3 C6913-5 See Section 5.4 A10109-10822 D4137-2 C6912-7 A10192-1 D8440-6
©2000 Crown International, Inc.
Parts 5-5
MA-3600VZ Service Manual
130366-1 Rev. A
20 19 12 24 10 9 17 13 18
15 16
14
21
13 12 6 7 23 8 9 10 25 24 11
26
22 28
1
5
4 27 3 2
Figure 5.3 Front Assembly
Parts 5-6
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.3 Front Assembly
Refer to Figure 5.3 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
2 2 2 2 1 2 1 1 2 2 2 2 2 2 1 2 3 3 3 1 1 1 1 2 5 1 2 8 1
Foam Filter Screw, #8 x 1.00 Type AB Flat HD Nylon Spacer Grille Clip Bottom Cover Knob Overlay Display Panel Handle Panel Cap Screw, #6-32 x .75 FLTHD TT End Cap Screw, 8-18 x 1.375 PNHD Screw, 4-40 x .37 Taptite Pan Display PWA 5KOhm Linear 31 Detent Pot 15MM Shaft Screw, 6-32 x .25 RDHD Washer, #6 Int Star Screw, 6-32 x ,437 Socket Cap Switch, DPST Pushbtn 6A 250VAC Chassis Lower Grille Extrusion Push Button, .75 Threaded Panel Cap Spacer Self-Stick Rubber Feet Insulator, 11 x 15 Transformer .5 x .136 Nylon Washer Velcro Tape Grille Assembly (includes Bottom Cover) Note: Old style grilles with the one-piece filter behind the grille are no longer available. If an older amplifier needs a new grille, the only option is to convert it to the new style by ordering CPN #M46504-3, which includes the bottom cover, grille extrusion, filters and necessary hardware. New grilles will not fit onto old bottom covers.
D7696-4 A10103-10816 A10101-12 A10173-1 F12609-8 D6265-9 D 9148-4 F12887-0 D8048J6 D8049J4 C10258-9 D8052J8 A10086-10824 C5961-5 See Section 5.4 C7280-8 A10086-10604 A10094-3 A10092-20607 C10180-5 see Section 5.3.1 D8752-4 D6013-3 F12647-8 C3342-0 D8249-1 A10101-5 D5796-6 M46504-3
©2000 Crown International, Inc.
Parts 5-7
MA-3600VZ Service Manual
130366-1 Rev. A
6
17
16 15 5 7
8 18
9 10 1
19 1
15
1 4 11 2 3 14 13 12 1
1
Figure 5.4 Back Panel Assembly
Parts 5-8
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.4 Back Panel Assembly
Refer to Figure 5.4 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
4 2 2 1 1 1 1 2 2 2 1 1 10 2 2 1 1 1 2
Dual Binding Post Screw, 8-32 x .37 RDHD MSCR #8 Int Star Washer, Black Standard PIP Assembly Power Cord, NEMA TT-30P Plug, Domestic Power Cord, HAR 230VAC 15A Plug, E17CE Strain Relief Edge Connector Circuit Breaker, 15A, Domestic Circuit Breaker, 8A, E17CE #4 Int Star Lockwasher Screw, 4-40 x .62 RDHD Jumper, 4 Position Ground Back Panel Washer, #6 Int Star Screw, 6-32 x .312 Pan HD T15 Taptite Aluminum Spacer PWB, PIP Interconnect Cable W/Terminals Daisy Ribbon Cable 2-Position Jumper
C10184-7 A10086-70806 A10094-5 See Section 5.3.9 D8247-5 D8844-9 C7315-2 C 6821-0 C10169-8 C10171-4 A10094-2 A10086-10410 D8855-5 F12864-9 A10094-3 C 9491-9 A10100-7 101240-1 D7623-8 D8573-4 F12812-8
©2000 Crown International, Inc.
Parts 5-9
MA-3600VZ Service Manual
130366-1 Rev. A
12 13 9 8 10 11
6 7 14
LEFT
5 4
3
15 2
16
1
Figure 5.5 Channel 1 Bi-Level Switch Assembly
Parts 5-10
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.5 Channel 1 (Left) Bi-Level Switch Assembly
Refer to Figure 5.5 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Not Pictured Not Pictured
7 1 2 4 1 4 4 2 2 1 4 4 2 3 4 1 1 1
Screw, 6-32 x .25 Socket Cap PWA, B-L Switch Clamp, TO-220 Bi-Level #6 Int Star Washer Left Shelf Screw, 4-40 x .25 RDHD #4 Int Star Lockwasher #8 Belleville Washer 8 x 32 Hex Nut PWA, CH1 B-L Bridge Screw, 6.32 x.25 Ind Hex Washer, #6 Int Star Bridge, 35A 400V Nylon Hex Spacer Capacitor, 6900uF 100V Elec. Insulator, 1.5 x .75 (Orange) Insulator, 1.5 x 1.25 (Gray) Channel 1 Bi-Level Switch Assembly Note: for units built before September, 1995 use CPN#M46663-7 Switch Assembly.
A10092-20604 See Section 5.4 D8301-1 A10094-4 Same as #1 125238-1 A10086-10404 A10094-2 A10098-3 A10102-6 See Section 5.4 A10107-70604 A10094-3 C10246-4 A10608-10 D7595-8 C9539-5 D8480-2 M46562-1
©2000 Crown International, Inc.
Parts 5-11
MA-3600VZ Service Manual
130366-1 Rev. A
11 10 9
12 13
RIGHT
8
7 6
5
4
3 14 2 16 1 15
Figure 5.6 Channel 2 Bi-Level Switch Assembly
Parts 5-12
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.6 Channel 2 (Right) Bi-Level Switch Assembly
Refer to Figure 5.6 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Not Pictured Not Pictured
1 1 7 2 4 4 2 1 2 2 4 4 4 4 3 1 1 1
Right Shelf PWA, B-L Switch Screw, 6-32 x .25 Socket Cap Clamp, TO-220 Bi-Level #6 Int Star Washer Capacitor, 6900uF 100V Elec. Bridge, 35A 400V PWA, CH2 B-L Bridge #8 Belleville Washer 8 x 32 Hex Nut Screw, 4-40 x .25 RDHD #4 Int Star Lockwasher Screw, 6.32 x.25 Ind Hex Washer, #6 Int Star Nylon Hex Spacer Insulator, 1.5 x .75 (Orange) Insulator, 1.5 x 1.25 (Gray) Channel 2 Bi-Level Switch Assembly Note: for units built before September, 1995 use CPN #M46662-9 Switch Assembly.
125238-1 See Section 5.4 A10092-20604 D8301-1 A10094-4 Same as #3 D7595-8 C10246-4 See Section 5.4 A10098-3 A10102-6 A10086-10404 A10094-2 A10107-70604 A10094-3 A10608-10 C9539-5 D8480-2 M46561-3
©2000 Crown International, Inc.
Parts 5-13
MA-3600VZ Service Manual
130366-1 Rev. A
5.3.7 Fan Assembly
Refer to Figure 5.7 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6
2 1 2 1 1 1 1
Screw, 6-32 x 5/16 FLTHD Fan Bracket Screw, 6-32 x .312 Pan HD T15 Taptite Transmotor, 120V, Domestic Transmotor, 240V, E17CE Fan Blace, 4.5 Inch CCW Label, 1A Fuse Replacement
C 7062-0 D8439-8 C 9491-9 H43076-1 H43358-3 C 9938-9 D8671-6
Figure 5.7 Fan Assembly Parts 5-14
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.8 Heatsink Assembly
(Channel 1 and 2 are Identical) Refer to Figure 5.8 for Exploded View
Item Quantity Description Part # (CPN)
1 2 3 4 5 6 7
24 12 12 2 2 2 2
Screw, 6-32 x .312 Pan HD T15 Taptite NPN Power Transistor PNP Power Transistor PTC LM234Z Thermal Sense Heatsink Silpad, 2.87 x 14.57 Note: use CPN #D6280-8 with Output PWB P10316-1 or earlier. Teflon Tubing
C 9491-9 C 8187-4 C 8188-2 D 8774-8 C 5826-0 M21322J8 D 7796-2
Not Pictured
126508-1
4
3
2 1
7 6
5
Figure 5.8 Heatsink Assembly
©2000 Crown International, Inc.
Parts 5-15
MA-3600VZ Service Manual
130366-1 Rev. A
Figure 5.9 Standard PIP Assembly
Parts 5-16
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.3.9 Standard PIP Assembly
Refer to Figure 5.9 for Exploded View
Item
Quantity
Description
Part # (CPN)
1 2 3 4 5 6 7 8 9
1 1 2 2 2 4 2 2 2
PIP-FX Panel PWB, PIP-FX/BB w/GND Lift Female XLR Connector Screw, #8 x 1/4 #6 PNHD Cap, .01uF 100V Axial Cer Screw, M3 x .5 x 7 MM PNHD Resistor, 22.0 Ohm .5W 5% #8 Int. Star Lockwasher Screw, 8-32 x .37 RDHD MSCR
M21176J8 128266-1 C 8163-5 C 7161-0 C 6806-1 A10330-9 A10266-2202 A10094-5 A10086-70806
©2000 Crown International, Inc.
Parts 5-17
MA-3600VZ Service Manual
130366-1 Rev. A
This Page Intentionally Left Blank
Parts 5-18
©2000 Crown International, Inc.
130366-1 Rev. A
MA-3600VZ Service Manual
5.4 Circuit Board Parts
This section includes electrical parts lists for this product. All serviceable parts and assemblies will have a Crown Part Number (CPN) listed in this section. The parts listed are current as of the date printed. Crown reserves the right to modify and improve its products for the benefit of its customers. Please note: where reference designations are listed as "installed on next assembly," the CPN (Crown Part Number) for the associated part may be found in Section 5.2, Mechanical Parts.
Q43382-3 Main PWA with Quad-Mute on D 8920-7 PWB. Not reverse compatible. For schematic see J0675-9.
Control PWAs:
Q42859-1 Control PWA on P10291-6 PWB. For schematic see J0454-9. Q43124-9 Control PWA on D 8172-5 PWB. For schematic see J0560-3. Q43296-5 Control PWA on D 8543-7 PWB. For schematic see J0643-7. Q43363-3 Control PWA on D 8696-3 PWB. For schematic see J0643-7 REV C. Q43364-1 Control PWA on D 8696-3 PWB. For schematic see J0643-7 REV C.
5.4.1 Circuit Board and Schematic Part Numbers
The schematics referenced and provided are representative only. There may be slight variations between amplifier to amplifier. These schematics are intended to be used for troubleshooting purposes only. Note on circuit board designations: Crown circuit boards are referenced with a PWA and/or PWB part number. PWA stands for Printed Wire Assembly. This is the completed circuit board with all components assembled. PWB stands for Printed Wire Board. This is the circuit board only, without components.
Output PWAs: (left and right are identical)
Q42893-0 Output PWA on P10316-1 PWB. For schematic see J0464-8. Q43100-9 Output PWA on P10373-2 PWB. Use Q43387-2 as service replacement. For schematic see J0547-0. Q43318-7 Output PWA on P10423-5 PWB. Use Q43387-2 as service replacement. For schematic see J0675-9. Q43387-2 Output PWA on P10423-5 PWB. For schematic see J0675-9.
Display PWAs:
Q42851-8 Display PWA on D 7617-0 PWB. For schematic see J0456-4. Q43314-6 Display PWA on D 8572-6 PWB. For schematic see J0456-4. Q43440-9 Display PWA on D 8897-7 PWB. For sch