Denon-DNS3000 cd.pdf part of Denon DNS3000 Denon-DNS3000 cd.part1.rar, CD player text manual preview

Text preview for : Denon-DNS3000 cd.pdf part of Denon DNS3000 CD player

Back to : Denon-DNS3000 cd.part1.ra | Home

For U.S.A., Canada, Europe
& Japan model

Ver. 1
SERVICE MANUAL
MODEL DN-S3000
TABLE TOP SINGLE CD PLAYER

For purposes of improvement, specifications and
design are subject to change without notice.

Please use this service manual with referring to the
operating instructions without fail.

Some illustrations using in this service manual are
slightly different from the actual set.

16-11, YUSHIMA 3-CHOME, BUNKYOU-KU, TOKYO 113-0034 JAPAN

X0180V.01 DE/CDM 0308
DN-S3000 2

SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.

LASER RADIATION
Do not stare into beam or view directly with optical instruments, class 3A laser product.

500V

1M

(1)

(2)

(1)

(2)

2
DN-S3000 3

DISASSEMBLY
(Follow the procedure below in reverse order when reassembling.)

1. SLIP DISK, SLIP MAT
(1) Remove a screw and pull out Slip Disc and Slip Mat.

.

Washer
Slip Disc

Slip Mat

Slip Sheet

Anti-static Sheet

2. PLATTER
(1) Remove Belt from Motor Pully.
(2) Remove 3 screws and pull out Platter.

.

Platter
Belt

Motor Pully

3
DN-S3000 4

3. DRIVE UNIT
(1) Remove 4 screws and pull out Drive Unit.
(2) Disconnect Flat cable and Connector.
(3) Detach Drive Unit.

Drive Unit

71

71

Connector
Flat cable
Drive Unit

Note:
Do not pull out aslant to prevent Flat cable damage.
Do not fail to pull AC cord from wall outlet before disconnect the Flat cable and Connector.
If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger.

4. COVER UNIT
(1) Remove 5 screws and pull out Cover Unit.
(2) Disconnect Connectors.
(3) Detach Cover unit.

Cover unit

CX042

Connector CX101

CX041

Connector

CX031

Note:
Do not fail to pull AC cord from wall outlet before disconnect Connectors.
If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger.

4
DN-S3000 5

5. SENSOR AND SCALE UNITS OF PLATTER
(1) Remove 2 screws and pull out Sensor Cover and Sensor unit.
(2) Remove a E Ring.
(3) Pull out Scale unit.

E Ring

Sensor Cover
Scale unit

Sensor unit

6. SENSOR AND SCALE UNITS OF SLIP DISC
(1) Remove 2 screws and pull out Sensor Cover and Sensor unit.
(2) Remove a screw and pull out Scale unit.

Scale unit

Sensor Cover

Sensor unit

7. POWER PWB
(1) Remove 5 screw and pull out Power PWB.

Power PWB

5
DN-S3000 6

8. DSP PWB UNIT
(1) Remove 9 screws and pull out DSP PWB unit.

DSP PWB unit

9. DRIVE COVER
(1) Remove 4 screws and pull out Drive cover.

Drive cover

10. DRIVE
(1) Move Drive Rack in arrow direction through the Hole on the bottom chassis.
Loader frame comes out.
(2) Pull up Loader panel while pulling it towards front.
(3) Remove 4 screws and pull out Drive.

Drive

6
DN-S3000 7

BLOCK DIAGRAM

DN-S3000

-HB,F1,F2
GND,+5

D16~31
128M TFS0 LRCK analog out
AMP
SDRAM TCK0 BCLK D/A
ROM RAM ADRESS ADSP21065L TXD0A MAIN DIT PANEL
DRIVE 32bit BUS TXD0B digital out �com
Trans
AK4353
ATAPI DSP
INTERFACE SHOCK PROOF
MAIN DOUT

256fs
TXD1B CLOCK TMP86CM47U
ROM32k
LED out
RAM1k
RAM control TFS1 Key scan
BUS 16Bit Bus D0~D15 TCK1
VR in
ATAPI select TXD1A
interface
DMA
CONTROL

FLAG DISC

SENSOR
CPU DSP 32.0M 32.0M 5v
D0~15 BUS
ATAP interface FW PULSE PANEL
9V 5.0V Interface DISC RV PULSE DISC

SENSOR
-HB,F1,F2 CPU SYSTEM URN TABLE DIR TURN TABLE

�9.0V TMP86CM47U CPU SERIAL 1 UART 5v TURN TABLE
micon SERIAL 2 UART X'EFFECT IN HB
SWITCHING
8M D0~D16 MN102H730F SERIAL 3 UART DRIVER X'EFFECT OUT
POWER SUPPLY
FRASH ADRESS 3.3-5V FADER FLT Driver FLT
memory
5.0V Ragurater 3.3V RAM10K ML9207
5.0V
adress
memo
4M
FRASH D/A
memory

CONTROL
motor
driver

Motor

7
DN-S3000 8

CONFIRMING THE SERVO
Required Measuring Implement
Reference disc (TCD784 or CO-74176)
1. What is Service Program
Service program is a special program intended for confirming servo functions etc.
2. Contents of Service Program
Switch on the power while pushing the PITCH BEND + button and SCRATCH MODE button at the same time. After actuating
the servo program, select an aiming process number with the SELECT knob, A button, B button, SAMP button, or SAMP B
button. Press the SELECT knob to execute the selected process, the process number is then displayed on the track indicator
of the display. To exit from the service program, just switch off the power.

Process No.
Function
(TRACK Contents
(Character-display)
Indication)
Check Version with JOG dial.
1. System com version No.: "Sys_XXXX "
com Version check 2. DSP soft version No.: "Dsp_XXXX "
01
(Version No.) 3. ATAPI com version No.: "Atapi_XXXX "
4. PANEL com version No.: "Panel_XXXX "
5. ROM drive mecha. com version No.: "Drive_XXXX "
OPEN/CLOSE
02 Performs open/close each time when the SELECT knob is pushed.
(Open Close)
ROM drive performs operation check when the SELECT knob is pushed, and
Drive Diagnostic indicates the operational result. If the disc holder open, it starts the operation check
03
(Drive_Diag) after closing. It indicates "Normal_End" if it ends normal. In case of error, ROM
drive error code is displayed in the character's lower portion as "E****".

Drive Data Read Starts continuous playback at its maximum reading speed from the beginning of
04 disc when the SELECT knob is pushed. It halts reading and stops if the knob is
(Data Read)
pushed again.

Turn the PLATTER to display the logging error codes in the occurred order.
("Error Data" is displayed.)
10 error logs are memorized at maximum.
Error Code Check
05 Kinds of Error Code, displayed
(Error Data)
Error Code Table (Appears only at Heat Run and Chucking Test function)
SELECT knob Pressing SELECT knob enters to data erase mode. ("Err Clear?" is displayed.)
If the SELECT knob is pushed again, the memorized error data are cleared.

Total time span of servo function that counted by the hour is displayed.
("Total Time" is displayed.)
Total Running Time The display time is less than 65535 hours.
06
(Total_Time) Note: No time is counted if powered down within 59 minutes.
Pressing SELECT knob enters to data erase mode. ("Time Clear?" is displayed.)
If the SELECT knob is pushed again, the memorized time data are cleared.
Starts automatic servo adjustment when the SELECT knob is pushed, and after
completing the adjustment, sort of the used disc is indicated. Data is selectable with
the PLATTER.
1. Disc check, CD/CD-RW
2. Focus gain data
Automatic 3. Focus balance data
07 Servo Adjustment 4. Focus offset data
call 5. Tracking gain data
6. Tracking balance data
7. Tracking offset data
8. PreAMP Tracking Sensor Gain
9. DSP Tracking Sensor Gain
10. PI offset

8
DN-S3000 9

Adjustment Value indication at
Adjustment Item
character portions.
1 Focus Gain 35 ~ 120
2 Focus Balance -20 ~ +20
3 Focus Offset -20 ~ +20
4 Tracking Gain 35 ~ 120
5 Tracking Balance -20 ~ +20
6 Tracking Offset -20 ~ +20
* Reference data.

3. TEST MODE
Process No.
Function
(TRACK Contents
(Character-display)
Indication)
Starting with the PLAY/PAUSE button, it repeats open/close of the tray and
playback.
Heat Run
A button - All tracks are played back if the track count is less than 20. Only the first and last
(H/R1_Normal)
tracks are played back if the tracks are more than 21. When any errors, it stops
and indicates error code (see Error Code Table).
Starting with the PLAY/PAUSE button, it repeats open/close of the tray, servo on,
Chucking Test and TOC read.
B button -
(H/R2_Tray) The display shows the number of the tray operation. When any errors, it stops and
indicates error code (see Error Code Table).
It starts system check when the PLAY/PAUSE button is pushed, and indicates the
status by performing plain operational check in the system .
1. Communication judge between the system com and DSP
2. DSP SDRAM write/read operation check
3. Communication judge between the system com and ATAPI com
SAMP System check
- 4. Communication judge between the ATAPI com and ROM drive
button (Sys._Check)
5. ROM drive operation check
After finishing the check, it indicates the result on the character display lower
portion.
When the 1. ~ 5. items are OK, their item numbers are indicated.
But if there is a NG item, its item number is not indicated.
Judges whether PLATTER can rotate at the specified rotating speed.
SAMP B
- The message "Platter_OK" is displayed on the character display if the rotating
button
speed meets the specification. Otherwise, "Platter_NG" is displayed.

4. Error Code Table (Appears only at Heat Run and Chucking Test function)
Error Code Contents
Automatic Adjustment Error
E1 00 Unable to detect disc
E1 01 Unable to adjust tracking offset
E1 03 Unable to adjust focus fine gain
E1 04 Unable to actuate focus
E1 05 Unable to actuate tracking
E1 06 Unable to adjust tracking fine gain
E2 02 Servo down during automatic adjustment
E3 00 Unable to read TOC
E4 00 Unable to close the disc holder in the regular time
E4 01 Unable to open the disc holder in the regular time
E5 00 Slide error

9
DN-S3000 10

Detailed error can be displayed by PLATTER when error occurs.

Error Indication
TR MIN SEC FRAM CHARACTER
Displays the track Displays the time at which error occurred. "H * * * * E ***"
No. in which error
occurred. Operation count Error code

5. System �com and DSP Version Upgrade
System �com and DSP can be upgraded in the following manner.

Version Upgrade Method
(1) Record the version upgrade software on a CD-R or CD-RW disc, only as one file with the format ISO9660 Mode-1.
The file name of the supplied version upgrade software should be used as is and this disc needs to finalize.
(2) After loading the disc made in above step 1, turn off the power. Then, turn on the power while pressing the NEXT TRACK
button and FAST SEARCH FWD ( ) button. The version upgrade starts with reading data of the disc.
(3) When you start version upgrade operation, messages "Version_Up" and "System&DSP" are displayed on the character dis-
play.
Recovery positions are turned on one by one from the left end according as the upgrade operation proceeds. When this op-
eration is completed, all recovery positions are turned on.
In case of some error or the power is turned off during the version upgrade, it may be impossible to operate at all thereafter.
Changing of IC502 on GU-3546 is necessary in this case, and software writing to IC502 should be done beforehand.
(4) When the upgrade is completed, the disk is ejected and operation returns to the normal mode.
(5) File name of the upgrade software indicates version numbers.
File name T3. * * * * * * . BIN

System com DSP version
version

6. ROM Drive (FG-5000) �com Version Upgrade
Drive (FG-5000) �com can be upgraded in the following manner.

Version Upgrade Method
(1) Record the version upgrade software on a CD-R or CD-RW disc, only as one file with the format ISO9660 Mode-1.
The file name of the supplied version upgrade software should be used as is and this disc needs to finalize.
(2) After turning on the power, load the disc made in above step 1 into the mecha. you want to upgrade the version.
(3) "Drive" and "Version UP?" are indicated in the character display. Press the CD EJECT button and remove the disc when not
upgrade the version.
(4) Press the PLAY/PAUSE to start the version upgrade. "Now Loading" is indicated.
(5) When the version upgrade is finished, "Complete" is indicated and the disc EJECT.
(6) Turn off the power once and turn on again after take out the disc.
The version upgrade ends in 20~30 seconds normally. If the power turned off underway or the version upgrade ends
abnormally, the drive may become malfunction. In such a case, version upgrade with PC will be needed.
(7) File name of the upgrade software indicates version number.
File name FG5K * * * * . BIN

Version number

10
DN-S3000 11

Only major semiconductors are shown, general semiconductors etc. are omitted to list.

1. IC's
Note : Abbreviation ahead of IC No. indicates the name of P.W.B., etc.

DS : DSP P.W.B.
PA : PANEL P.W.B.
CD : CD-ROM P.W.B.
ADSP-21065L (DS: IC401)
208 157

1 156

TOP VIEW

52 105

53 104
ADSP-21065L Terminal Function
Pin Symbol Symbol
Port Name I/O DET Ext Ini Res Function
No. (IC301) (IC401)
1 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
2 RFS0 YLRCK YLRCK I -- IPu -- H Receive frame sync (LRCK) signal (Serial port IN 0)
3 GND GND GND -- -- -- -- -- GND
4 RCLK0 YBCK YBCK I -- -- -- -- Receive frame sync (BCK) signal (Serial port IN 0)
5 DR0A ADDATA ADDATA I -- IPu -- H Data receive A (serial port IN 0)
6 DR0B I -- IPu -- H Data receive B (serial port IN 0)
7 TFS0 YLRCK YLRCK I -- IPu -- H Send frame sync (LRCK) signal (Serial port OUT 0)
8 TCLK0 YBCK YBCK I -- -- -- -- Send frame sync (BCK) signal (Serial port OUT 0)
9 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
10 GND GND GND -- -- -- -- -- GND
11 DT0A MOUT1 MOUT2 O -- IPu -- H Data send A (Serial port OUT 0)
12 DTOB DOUT1 DOUT2 O -- IPu -- H Data send B (Serial port OUT 0)
13 RFS1 LRCK1 LRCK2 I -- IPu -- H Receive frame sync (LRCK) signal (Serial port IN 1)
14 GND GND GND -- -- -- -- -- GND
15 RCLK1 BCK1 BCK2 I -- -- L -- Receive frame sync (BCK) signal (Serial port IN 1)
16 DR1A SAMP2 SAMP1 I -- IPu -- H Data receive A (serial port IN 1)
17 DR1B I -- IPu -- H Data receive B (serial port IN 1)
18 TFS1 LRCK2 LRCK1 I/O -- IPu -- H Send frame sync (LRCK) signal (Serial port OUT 1)
19 TCLK1 BCK2 BCK1 I/O -- -- -- -- Send frame sync (BCK) signal (Serial port OUT 1)
20 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
21 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
22 DT1A SOUT1 SOUT2 O -- IPu -- H Data send A (Serial port OUT 1)
23 DT1B SAMP1 SAMP2 O -- IPu -- H Data send B (Serial port OUT 1)
24 PWM_EVENT1 I/O -- Pd -- L PWM1 output
25 GND GND GND -- -- -- -- -- GND
26 PWM_EVENT0 I/O -- Pd -- L PWM0 output
27 BR1_ I -- Pu -- H Multi-processing bus request 1
28 BR2_ I -- Pu -- H Multi-processing bus request 1
29 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
30 CLKIN I -- -- -- -- Clock input
31 XTAL_ O -- -- -- -- X'tal oscillator pin
32 VDD VDD VDD -- -- -- -- -- Power (+3.3V)

11
DN-S3000 12

Pin Symbol Symbol
Port Name I/O DET Ext Ini Res Function
No. (IC301) (IC401)
33 GND GND GND -- -- -- -- -- GND
34 SDCLK1 O -- Pd -- L SDRAM clock enable 1
35 GND GND GND -- -- -- -- -- GND
36 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
37 SDCLK0 I/O -- -- -- -- SDRAM clock enable 0
38 DMAR1_ I -- Pu H H DMA request 1
39 DMAR2_ I -- Pu H H DMA request 2
40 HBR_ I -- Pu -- H Host bus request (BOOT)
41 GND GND GND -- -- -- -- -- GND
42 RAS_ I/O -- Pu H H SDRAM row access strobe
43 CAS_ I/O -- Pu H H SDRAM column access strobe
44 SDWE_ I/O -- Pu H H SDRAM write enable
45 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
46 DQM O -- -- -- -- SDRAM data mask
47 SDCKE I/O -- -- H -- SDRAM clock enable
48 SDA10 O -- Pd L L SDRAM A10
49 GND GND GND -- -- -- -- -- GND
50 DMAG1_ O -- -- H -- DMA ground 1
51 DMAG2_ O -- -- H -- DMA ground 2
52 HBG_ O -- -- H -- Host bus ground (BOOT)
53 BMSTR O -- -- H -- Bus master output (H out)
54 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
55 CS_ I -- -- L L Chip select (BOOT)
56 SBTS_ I -- Pu H H Extend bus three state
57 GND GND GND -- -- -- -- -- GND
58 WR_ I/O -- -- -- -- Memory write strobe
59 RD_ I/O -- -- -- -- Memory read strobe
60 GND GND GND -- -- -- -- -- GND
61 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
62 GND GND GND -- -- -- -- -- GND
63 REDY O -- -- -- -- Host bus ACK
64 SW_ I/O -- -- -- -- Sync type write select
65 CPA_ I/O -- -- -- -- Core priority access
66 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
67 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
68 GND GND GND -- -- -- -- -- GND
69 ACK I/O -- -- -- -- Memory ACK
70 MS0_ I/O -- Pu H H Memory select 0
71 MS1_ I/O -- -- -- -- Memory select 1
72 GND GND GND -- -- -- -- -- GND
73 GND GND GND -- -- -- -- -- GND
74 MS2_ I/O -- -- -- -- Memory select 2
75 MS3_ I/O -- -- -- -- Memory select 3
76 FLAG11 DMABSY1 DMABSY2 O -- Pu -- H General flag 11 (In DMA flag L: DMA)
77 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
78 FLAG10 SAMPCOP SAMPCOPY I/O -- Pu -- H General flag 10 (In SAMPLER copy flag)
79 FLAG9 JOGB1 JOGB2 I -- -- -- -- General flag 9 (JOG turning direction detect signal B)
80 FLAG8 JOGA1 JOGA2 I -- -- -- -- General flag 8 (JOG turning direction detect signal A)
81 GND GND GND -- -- -- -- -- GND
82 DATA0 I/O -- -- -- -- Ext. bus data 0
83 DATA1 I/O -- -- -- -- Ext. bus data 1
84 DATA2 I/O -- -- -- -- Ext. bus data 2
85 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
86 DATA3 I/O -- -- -- -- Ext. bus data 3
87 DATA4 I/O -- -- -- -- Ext. bus data 4
88 DATA5 I/O -- -- -- -- Ext. bus data 5
89 GND GND GND -- -- -- -- -- GND
90 DATA6 I/O -- -- -- -- Ext. bus data 6
91 DATA7 I/O -- -- -- -- Ext. bus data 7
92 DATA8 I/O -- -- -- -- Ext. bus data 8
93 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
94 GND GND GND -- -- -- -- -- GND

12
DN-S3000 13

Pin Symbol Symbol
Port Name I/O DET Ext Ini Res Function
No. (IC301) (IC401)
95 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
96 DATA9 I/O -- -- -- -- Ext. bus data 9
97 DATA10 I/O -- -- -- -- Ext. bus data 10
98 DATA11 I/O -- -- -- -- Ext. bus data 11
99 GND GND GND -- -- -- -- -- GND
100 DATA12 I/O -- -- -- -- Ext. bus data 12
101 DATA13 I/O -- -- -- -- Ext. bus data 13
102 NC -- -- -- -- -- NC
103 NC -- -- -- -- -- NC
104 DATA14 I/O -- -- -- -- Ext. bus data 14
105 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
106 GND GND GND -- -- -- -- -- GND
107 DATA15 I/O -- -- -- -- Ext. bus data 15
108 DATA16 I/O -- -- -- -- Ext. bus data 16
109 DATA17 I/O -- -- -- -- Ext. bus data 17
110 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
111 DATA18 I/O -- -- -- -- Ext. bus data 18
112 DATA19 I/O -- -- -- -- Ext. bus data 19
113 DATA20 I/O -- -- -- -- Ext. bus data 20
114 GND GND GND -- -- -- -- -- GND
115 NC -- -- -- -- -- NC
116 DATA21 I/O -- -- -- -- Ext. bus data 21
117 DATA22 I/O -- -- -- -- Ext. bus data 22
118 DATA23 I/O -- -- -- -- Ext. bus data 23
119 GND GND GND -- -- -- -- -- GND
120 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
121 DATA24 I/O -- -- -- -- Ext. bus data 24
122 DATA25 I/O -- -- -- -- Ext. bus data 25
123 DATA26 I/O -- -- -- -- Ext. bus data 26
124 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
125 GND GND GND -- -- -- -- -- GND
126 DATA27 I/O -- -- -- -- Ext. bus data 27
127 DATA28 I/O -- -- -- -- Ext. bus data 28
128 DATA29 I/O -- -- -- -- Ext. bus data 29
129 GND GND GND -- -- -- -- -- GND
130 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
131 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
132 DATA30 I/O -- -- -- -- Ext. bus data 30
133 DATA31 I/O -- -- -- -- Ext. bus data 31
134 FLAG7 DFLG12 DFLG22 I/O -- Pu -- H General flag 7 (RESERVE)
135 GND GND GND -- -- -- -- -- GND
136 FLAG6 DFLG11 DFLG21 I/O -- Pu -- H General flag 6 (RESERVE)
137 FLAG5 DTIMB1 DTIMB2 O -- -- -- -- General flag 5 (Pulse output for generating monitor play time)
138 FLAG4 DTIMA1 DTIMA2 O -- -- -- -- General flag 4 (Pulse output for generating main play time)
139 GND GND GND -- -- -- -- -- GND
140 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
141 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
142 NC -- -- -- -- -- NC
143 ID1 I -- -- L L Multi-processing ID1 (Single processor: 0)
144 ID0 I -- -- L L Multi-processing ID2 (Single processor: 0)
145 EMU_ EMU1_ EMU2_ O -- -- -- -- Emulation status
146 TD0 TD01 TD02 O -- -- -- -- Test data output (JTAG)
147 TRST_ TRST1_ TRST2_ I -- IPu -- H Test reset (JTAG)
148 TDI TDI1 TDI2 I -- Pd -- L Test data input (JTAG)
149 TMS TMS1 TMS2 I -- IPu -- H Test mode select (JTAG)
150 GND GND GND -- -- -- -- -- GND
151 TCK TCK1 TCK2 I -- Pu -- H Test clock (JTAG)
152 BSEL I -- -- H H EPROM boot select (Boot by EPROM: 1)
153 BMS_ BMS1_ BMS2_ I -- -- H H Boot memory select (Host processor boot: 1)
154 GND GND GND -- -- -- -- -- GND
155 GND GND GND -- -- -- -- -- GND
156 VDD VDD VDD -- -- -- -- -- Power (+3.3V)

13
DN-S3000 14

Pin Symbol Symbol
Port Name I/O DET Ext Ini Res Function
No. (IC301) (IC401)
157 RESET_ DRES_ DRES_ I -- -- H L DSP reset signal
158 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
159 GND GND GND -- -- -- -- -- GND
160 ADDR23 I/O -- -- -- -- Ext. bus address 23
161 ADDR22 I/O -- -- -- -- Ext. bus address 22
162 ADDR21 I/O -- -- -- -- Ext. bus address 21
163 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
164 ADDR20 I/O -- -- -- -- Ext. bus address 20
165 ADDR19 I/O -- -- -- -- Ext. bus address 19
166 ADDR18 I/O -- -- -- -- Ext. bus address 18
167 GND GND GND -- -- -- -- -- GND
168 GND GND GND -- -- -- -- -- GND
169 ADDR17 I/O -- -- -- -- Ext. bus address 17
170 ADDR16 I/O -- -- -- -- Ext. bus address 16
171 ADDR15 I/O -- -- -- -- Ext. bus address 15
172 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
173 ADDR14 I/O -- -- -- -- Ext. bus address 14
174 ADDR13 I/O -- -- -- -- Ext. bus address 13
175 ADDR12 I/O -- -- -- -- Ext. bus address 12
176 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
177 GND GND GND -- -- -- -- -- GND
178 ADDR11 I/O -- -- -- -- Ext. bus address 11
179 ADDR10 I/O -- -- -- -- Ext. bus address 10 (SDRAM: Connects SDA10)
180 ADDR9 I/O -- -- -- -- Ext. bus address 9
181 GND GND GND -- -- -- -- -- GND
182 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
183 ADDR8 I/O -- -- -- -- Ext. bus address 8
184 ADDR7 I/O -- -- -- -- Ext. bus address 7
185 ADDR6 I/O -- -- -- -- Ext. bus address 6
186 GND GND GND -- -- -- -- -- GND
187 GND GND GND -- -- -- -- -- GND
188 ADDR5 I/O -- -- -- -- Ext. bus address 5
189 ADDR4 I/O -- -- -- -- Ext. bus address 4
190 ADDR3 I/O -- -- -- -- Ext. bus address 3
191 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
192 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
193 ADDR2 I/O -- -- -- -- Ext. bus address 2
194 ADDR1 I/O -- -- -- -- Ext. bus address 1
195 ADDR0 I/O -- -- -- -- Ext. bus address 0
196 GND GND GND -- -- -- -- -- GND
197 FLAG0 DR_/W1 DR_/W2 I/O -- -- -- -- General flag 0 (Command read write select)
198 FLAG1 DACK1_ DACK2_ I/O -- -- -- -- General flag 1
199 FLAG2 DBSY1 DBSY2 I/O -- -- -- -- General flag 2
200 VDD VDD VDD -- -- -- -- -- Power (+3.3V)
201 FLAG3 DFLG10 DFLG20 I/O -- Pu -- H General flag 3 (RESERVE)
202 NC -- -- -- -- -- --
203 NC -- -- -- -- -- --
204 GND GND GND -- -- -- -- -- GND
205 IRQ0_ DREQ1 DREQ2 I -- Pu -- H Interrupt request input 0 (SYS mcom interface)
206 IRQ1_ DREQ1_ DREQ2_ I -- Pu -- L Interrupt request input 1 (SYS mcom interface)
207 IRQ2_ JOGINT1 JOGINT2 I -- -- -- -- Interrupt request input 2 (JOG turning speed detect signal)
208 NC -- -- -- -- -- NC

14
DN-S3000 15

M5705Q (CD: IC501)

XSAWRCVCO

XSPDOFTR2

XSPLLFTR2
AVDD5_PL
XSVR_PLL
XSFTROPI

XSPDIREF
XSFDIREF
XSVREFO

XRSDCLK
AVSS_PL

XRCASJ
XRRASJ
XTPLCK

XRD(10)

XRD(11)
XTSLRF

XRA(10)
XRA(11)

XRWEJ
XSFDO

XROEJ

XRD(7)
XRD(8)
XRD(6)

XRD(9)
XRD(5)

XRD(4)
XRA(3)
XRA(2)
XRA(1)
XRA(0)
XRA(4)
XRA(5)
XRA(6)

XRA(7)

XRA(8)
XRA(9)
GND

GND

GND
VDD

VDD

VDD
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
AVSS-DS 1 132 XRD(3)
XSRFIN 2 131 XRD(12)
XSIPIN 3 130 GND
AVDD5-DS 4 129 XRD(2)
XSDSSLV 5 128 XRD(13)
XSRSLINT 6 127 XRD(1)
VDD 7 126 XRD(14)
XSAWRC 8 125 XRD(0)
XSRFGC 9 124 XRD(15)
XSEFGC 10 123 XHD(7)
XSFOCUS 11 122 XHD(8)
XSTRACK 12 121 XHD(6)
XSSLEG 13 120 XHD(9)
AVDD5-DA 14 119 XHD(5)
XSMOTOR 15 118 XHD(10)
AVSS-DA 16 117 XHD(4)
XSRFRPLP 17 116 XHD(11)
XSTELP 18 115 VDD
XSVREF2 19 114 XHD(3)
XSRFRP 20 113 XHD(12)
XSTEXI 21 112 XHD(2)
AVSS-AD 22 111 XHD(13)
XSTEI 23 110 GND
XSFEI 24 109 XHD(1)
XSAEI 25 108 XHD(14)
AVDD5-AD 26 107 XHD(0)
XSSBAD 27 106 XHD(15)
GND 28 105 XHDRQ
XSDFCT 29 104 XHIOWJ
XSCSJ 30 103 XHIORJ
XSCLK 31 102 XHIORDY
XSDATA 32 101 XHDACKJ
XSLDC 33 100 XHINT
XSFGIN 34 99 XHCS16J
XSSPDON 35 98 XHA(1)
XSFLAG(3) 36 97 XHPDIAGJ
XSFLAG(2) 37 96 XHA(0)
XSFLAG(1) 38 95 XHA(2)
XSFLAG(0) 39 94 XHCS1J
XMP1_7 40 93 XHCS3J
XMP1_6 41 92 XHDASPJ
GND 42 91 XMA(15)
NC 43 90 XMA(14)
XMP1_4 44 89 XMA(13)
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
XMP1_3
XMFSCSJ
XMP1_2
XGPIO(2)
XMP1_1
XMRSTJ
XGPO(1)
XGPO(0)
XCRSTJ
XMPSENJ
VDD
XMALE
XMP1_0
VDD
XOSC1
XOSC2
GND
XMD(0)
XMD(1)
XMD(2)
XMD(3)
XMD(4)
XMD(5)
XMD(6)
XMD(7)
XMCSJ
XMRDJ
XMWRJ
XMINT1J
XMA(11)
XMA(10)
VDD
XMA(9)
XMA(8)