Fostex-FD4 multitracker.pdf part of Fostex FD4 Fostex-FD4 multitracker.part1.rar, multitracker text manual preview

Text preview for : Fostex-FD4 multitracker.pdf part of Fostex FD4 multitracker

Back to : Fostex-FD4 multitracker.p | Home

Service Manual

Model

FD-4
DIGITAL MULTITRACKER

CAUTION: CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SOLT, FULLY INSERT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND.

The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

"WARNING"
"TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE."

SAFETY INSTRUCTIONS
1. 2. 3. 4. 5. Read instructions - All the safety and operating instructions should be read before the appliance is operated. Retain instructions - The safety and operating instructions should be retained for future reference. Heed warnings - All warnings on the appliance and in the operating instructions should be adhered to. Follow instructions - All operating and use instructions should be followed. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer. 9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarization - The precautions that should be taken so that the grounding or polarization means of an appliance is not defeated. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. Nonuse Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. Damage requiring Service - The appliance should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the appliance; or C. The appliance has been exposed to rain; or D. The appliance does not appear to operate normally or exhibits a marked changed in performance; or E. The appliance has been dropped, or the enclosure damaged. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

10.

11.

12.

6.

13. 14.

15.

7.

8.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

16.

17.

FD-4

TABLE OF CONTENTS 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. CONTROLS, INDICATORS AND CONNECTORS . . . . . . . . . . . 3. SOFTWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. SERVICE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. ERROR CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. INSTALLING 2.5" INTERNAL HARD DISK DRIVE . . . . . . . . . 7. EXPLODED VIEW, PCB ASSEMBLY AND PARTS LIST . . . . . 8. CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7 11 12 19 20 24 41

NOTES * Service mode, error code list, explode view, PCB assembly, parts list and circuit diagrams are given in this
manual to assist the service technician in maintaining the Model FD-4.

* The following accessories are supplied with FD-4 as the standard accessories.
Owner's manual : 8288414100 (for export model) : 8288415000 (for domestic model)

* Following is the packing material for the Model FD-4.
Carton, inner, FD-4 Packing, side, L, FD-4 Packing, side, R, FD-4 : 8228716000 : 8228440000 : 8228441000

CAUTION
! Parts marked with this sign are safety critical components. They must always be replaced with identical

components. Refer to the Fostex Parts List and ensure exact replacement.

3

FD-4

1. SPECIFICATIONS
RECORD & REPRODUCE Recording Medium Standard Sampling Frequency Quantization Emphasis Recording Time (mono track min.) Fs: 32 kHz Fs: 44.1 kHz Number of Tracks NORMAL / MASTERING MODE 1 MASTERING MODE 2 Number of simultaneous recording tracks Number of simultaneous playback tracks Number of tracks to be pasted at a time Recording Format Recording Mode External fixed / removable hard disk drive SCSI-2 or better 32 kHz, 44.1 kHz 12-bit nonlinear, 16-bit linear Not available About 33 min. / 100 MB (up to 24 hours) at maximum About 18 min. / 100 MB (up to 24 hours) at maximum 6 (4 + 2 additional tracks) 4 2 4 6 FDMS-3 NORMAL MODE (Fs: 32 kHz, 4 + 2 tracks, default) MASTERING MODE 1 (Fs: 44.1 kHz, 4 + 2 tracks) MASTERING MODE 2 (Fs: 44.1 kHz, 4 tracks)

ELECTRICAL (0 dBV = 1 V) · MIXER SECTION Reference Input Level MIC Impedance LINE Impedance RECORDER IN Impedance AUX RTN Impedance DATA IN Connector Format Reference Output Level STEREO Load impedance AUX SEND Load Impedance MONITOR Load impedance HEADPHONE DATA OUT Connector Format
4

-50, -30 dBV 20 k or more -10 dBV 20 k or more -10 dBV 20 k or more -20 dBV 8 k or more Square shape optical IEC consumer optical standard IEC 958 Part 3 -10 dBV 10 k or more -10 dBV 10 k or more -10 dBV 10 k or more 20 mW at maximum (Load: 16 ) 50 mW at maximum (Load: 50 ) Square shape optical IEC consumer optical standard IEC 958 Part 3

FD-4

ELECTRICAL (continued) SCSI DATA input / output Connector D-SUB 25-pin Protocol SCSI-2, unbalanced transfer method Transfer type Asynchronous Number of device to be connected 1 Fader / Knob Position at Reference Input / Output MASTER fader At 8 ~ 9 position (AUX RTN : -20 dBV / 1 kHz, AUX RTN VR: MAX. Adjust master fader for -10 dBV output at STEREO OUT.) MONITOR knob Adjust MONITOR knob for -10 dBV output at MONITOR OUTPUT. (MON SEL: ST+MON, MON) INPUT fader At 7 ~ 8 position (INPUT: -10 dBV / 1 kHz, EQ GAIN: 0, PAN: L (R). Adjust input fader for -10 dBV output at STEREO OUT.) Output Level INPUT (1 ~ 4) AUX SEND -10 dBV +0, -2 dB (INPUT: -10 dBV / 1 kHz, EQ GAIN: 0, PAN: L (R), AUX1, 2 VR: CH MAX, input fader: at 7 ~ 8 position.) INPUT (1 ~ 4) MONITOR -10 dBV ± 1 dB (INPUT: -10 dBV / 1 kHz, EQ GAIN: 0, PAN: L (R), MON VR: MON MAX, MON PAN: L (R), input fader: at 7 ~ 8 position.) Frequency Response INPUT (1 ~ 4) MONITOR 20 ~ 20 kHz +1, -3 dB (INPUT: -50 dBV) 20 ~ 20 kHz +1, -2 dB (INPUT: -10 dBV) INPUT (1 ~ 4) AUX SEND 20 ~ 20 kHz +1, -2 dB (INPUT: -10 dBV) AUX RTN MONITOR OUT 20 ~ 20 kHz +1, -2 dB (AUX RTN: -20 dBV) AUX RTN PHONES 80 ~ 20 kHz +1, -2 dB (AUX RTN: -20 dBV, at 20 mW / 16 ) EQ Characteristics High (12 kHz) & Low (80 Hz) +15 dB ± 3 dB at "+15" position -15 dB ± 3 dB at "-15" position Mid (200 Hz ~ 5 kHz) +15 dB ± 3 dB at "+15" position -15 dB ± 3 dB at "-15" position S/N INPUT INPUT LEVEL -50 dBV -38 dBV -10 dBV +2 dBV -50 dBV -38 dBV -10 dBV +2 dBV VR MIN OUTPUT LEVEL -10 dBV AUX SEND +2 dBV AUX SEND -10 dBV AUX SEND +2 dBV AUX SEND -10 dBV MONITOR +2 dBV MONITOR -10 dBV MONITOR +2 dBV MONITOR PHONES S/N UNWTD. 66 dB or more 78 dB or more 80 dB or more 92 dB or more 63 dB or more 75 dB or more 73 dB or more 85 dB or more AWTD. 68 dB or more 80 dB or more 82 dB or more 94 dB or more 65 dB or more 77 dB or more 75 dB or more 87 dB or more -75 dBV or less
5

INPUT 4

Residual Noise

FD-4

ELECTRICAL (continued) Distortion INPUT INPUT LEVEL -40 dBV 0 dBV 0 dBV -10 dBV -10 dBV OUTPUT LEVEL 0 dBV MONITOR 0 dBV MONITOR 0 dBV AUX SEND 0 dBV MONITOR 20 mW PHONES S/N UNWTD. 100 ~ 10 kHz 100 ~ 10 kHz 100 ~ 10 kHz 100 ~ 10 kHz 1 kHz AWTD. 0.05 % or less 0.05 % or less 0.05 % or less 0.05 % or less 0.10 % or less

AUX RTN

Crosstalk Click Noise Power on / off Other switching MIDI Controlling

60 dB or more / 1 kHz -20 dBV p-p or less -50 dBV p-p or less Operation check should be executed using the test mode with connecting the MIDI IN and OUT terminal.

· RECORDER SECTION Frequency Response Fs: 44.1 kHz Fs: 32 kHz Full Scale Output Level (Ref: -12dB) Dynamic Range Total Harmonic Distortion Fs: 44.1 kHz Fs: 32 kHz Channel Separation S/N Power Consumption JPN Others

20 ~ 20 kHz +1, -2 dB 20 ~ 14.5 kHz +1, -2 dB +2 dBV ± 1 dB (Fs: 32 kHz / 44.1 kHz) 88 dB or more (Fs: 32 kHz / 44.1 kHz) 0.02 % or less 0.08 % or less 80 dB or more / 1 kHz at max. recording level (Fs: 32 kHz / 44.1 kHz) 88 dB or more (A-WTD., Fs: 32 kHz / 44.1 kHz) 13 W +5, -20 % 15 W +5, -20 %

Specifications and appearance are subject to change without notice for product improvement.

6

FD-4

2. CONTROLS, INDICATORS & CONNECTORS
Rear Panel

Control Panel

AUX
0

AUX
0

AUX
0

AUX
0

AUX RTN

AUX1

AUX2

AUX1

AUX2

AUX1

AUX2

AUX1

AUX2

EQ
HIGH 0 HIGH

EQ
0 HIGH

EQ
0 HIGH

EQ
0 1

MID GAIN 0

+ MID GAIN

0

+ MID GAIN

0

+ MID GAIN

0

+ 2

0

10

MID SHIFT 300 200 LOW 0 900

+ MID SHIFT 2k 5k LOW 300

900

+ MID SHIFT 2k 5k 0 LOW 300

900

+ MID SHIFT 2k 5k 0 LOW 300

900

+

0

10

2k 5k

200

200

200 0

RECORD TRACK
1/L 2/R 3/L 4/R L R

-

+

-

+

-

+

-

+

MON
0

MON
0

MON
0

MON
0

MON SECTION
PREVIEW START IN OUT END

ADD. TRACK
DISP SEL SETUP TIME BASE SEL

IN

OUT

INPUT PAN

TRK1 PAN

INPUT

TRK2 PAN

INPUT

TRK3 PAN

INPUT

TRK4 MASTER

AUTO PUNCH AUTO RTN
HOLD/ 0 10 PGM SEL VARI PITCH AUTO RTN AUTO PLAY STORE EDIT UNDO/ REDO

CLIPBOARD
EXECUTE /YES EXIT /NO

MON L

MON R

MON L

MON R

MON L

MON R

MON L

MON R

PAN

PAN

PAN

PAN
EJECT

LOCATE

L

R

L

R

L

R

L

R SELECTOR L/R L/R+MON MON AUTO PUNCH CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END STOP PLAY SHIFT P. EDIT LOC MEM JOG SHUTTLE

INPUT SEL
INPUT OFF TRK 1

INPUT SEL
INPUT OFF TRK 2

INPUT SEL
INPUT OFF TRK 3

INPUT SEL
INPUT OFF TRK 4

1
10

2
10

3
10

4
10

L/R
10

RECORD

REWIND/

F FWD/

5

5

5

5

5

0

0

0

0

0

H M L

H M L DIGITAL MULTITRACKER

LEVEL

LEVEL

Front Panel
1 2 3 4

POWER R MON OUT L R ST OUT L 2
ACCESS

AUX SEND

SCSI 1 R

AUX RTN 2 MONO/L

DATA IN

DATA OUT R

PUNCH IN/OUT AUX RTN 1 MONO/L

MIDI IN 4 INSERT

MIDI OUT 3 INPUT 4

RECORDER IN R L INPUT 3

7

FD-4

Control Panel (Mixer Section)

AUX
0

AUX
0

AUX
0

AUX
0

AUX RTN

7
AUX1 AUX2 AUX1 AUX2 AUX1 AUX2 AUX1 AUX2

EQ
HIGH 0 HIGH

EQ
0 HIGH

EQ
0 HIGH

EQ
0 1

MID GAIN 0

+ MID GAIN

0

+ MID GAIN

0

+ MID GAIN

0

+ 2

0

10

8

-

+ 900 2k 5k 0 LOW MID SHIFT 300

900

+ MID SHIFT 2k 5k 0 LOW 300

900

+ MID SHIFT 2k 5k 0 LOW 300

900

+

0

10

6

MID SHIFT 300 200 LOW

2k 5k 0

200

200

200

-

+

-

+

-

+

-

+

MON
0

MON
0

MON
0

MON
0

MON SECTION

5
INPUT PAN TRK1 PAN INPUT TRK2 PAN INPUT TRK3 PAN INPUT TRK4 MASTER

4
MON L MON R MON L MON R MON L MON R MON L MON R 0 10

9
PAN PAN PAN PAN
L R L R L R L R SELECTOR L/R L/R+MON MON

3
INPUT SEL
INPUT

INPUT SEL
INPUT OFF TRK 2

INPUT SEL
INPUT OFF TRK 3

INPUT SEL
INPUT OFF TRK 4

2
1
10

OFF TRK 1

10

2
10

3
10

4
10

L/R
10

5

5

5

5

5

0

0

0

0

0

1

H M L

H M L

11 12

LEVEL

LEVEL

1. Input faders [1-4] 2. Input select switches [INPUT SEL (INPUT/OFF/TRK)] 3. Panpot knobs [PAN (L/R)] 4. Monitor panpot knobs [PAN (MON L/MON R)] 5. Monitor level control knob [MON (INPUT/TRK)] 6. Equalizer control knobs [EQ (HIGH/MID/LOW)] 7. AUX send knobs [AUX (AUX 1/AUX 2)]

8. AUX return knobs [AUX RTN (1, 2)] 9. Monitor master knob [MONITOR SECTION (MASTER)] 10. Monitor select switch [SELECTOR (L/R, L/R+MON, MON)] 11. Master fader [L/R] 12. Input level switches [LEVEL (H/M/L)]

8

FD-4

Control Panel (Recorder Section)

41 14 13 40 15 16
RECORD TRACK
1/L 2/R 3/L 4/R L R

37 38 34 33 35

17
ADD. TRACK

39
PREVIEW START IN OUT END

18
DISP SEL SETUP TIME BASE SEL EXECUTE /YES EXIT /NO

IN

OUT

36
HOLD/

AUTO PUNCH AUTO RTN
STORE EDIT UNDO/ REDO

CLIPBOARD

32 28 29 30 31 27 26

PGM SEL VARI PITCH AUTO RTN AUTO PLAY

EJECT

19 20 21 22 23 24 25

LOCATE

ACCESS

SHIFT

P. EDIT

LOC MEM

JOG

SHUTTLE

AUTO PUNCH RECORD

CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END STOP PLAY

REWIND/

F FWD/

DIGITAL MULTITRACKER

13. Record track select keys [RECORD TRACK (1/L, 2/R, 3/L, 4/R, L, R)] 14. LCD 15. Contrast adjustment knob 16. Display indication select key 17. Setup key [SETUP] 18. Time Base select key 19. Execute/Yes key [EXECUTE/YES] 20. Exit/No key [EXIT/NO/ EJECT ] 21. Access LED [ACCESS] 22. JOG dial [JOG/ SHUTTLE ] 23. Fast forward button [F FWD/ ] 24. Rewind button [REWIND/ ] 25. Play button [PLAY] 26. Stop button [STOP] 27. Record button [RECORD/ AUTO PUNCH ]

28. Shift key [ SHIFT ] 29. Vari Pitch key [VARI PITCH/ P.EDIT ] 30. Auto Return/Auto Play mode on/off key [AUTO RTN/AUTO PLAY] 31. Locate key [LOCATE/ LOC MEM ] 32. Hold/ key [HOLD/ ] 33. Store key [STORE] 34. Undo/Redo key [UNDO/REDO] 35. Edit key [EDIT] 36. Auto Return Start key [AUTO RTN START/ PREVIEW ] 37. Auto Return End key [AUTO RTN END/ PREVIEW ] 38. Auto Punch In key [AUTO PUNCH IN/ PREVIEW ] 39. Auto Punch Out key [AUTO PUNCH OUT/ PREVIEW ] 40. Clipboard In key [CLIPBOARD IN/ PREVIEW ] 41. Clipboard Out key [CLIPBOARD OUT/ PREVIEW ]

9

FD-4

Front Panel

1

2

1

2

3

4

1. Input jacks [1, 2, 3, 4] (Phone) 2. Headphone jack [PHONES] (TRS Phone)

Rear Panel

1

2

3

4

5

6

INPUT 4

INPUT 3

R MON OUT L

R

ST OUT

L

2

AUX SEND

1

R

AUX RTN 2 MONO/L

R

AUX RTN 1 MONO/L

4

INSERT

3

POWER

SCSI

DATA IN

DATA OUT

PUNCH IN/OUT

MIDI IN

MIDI OUT

RECORDER IN R L

15
1. 2. 3. 4. 5. 6.

14

13 12 11 10 9
8. 9. 10. 11. 12. 13. 14. 15.

8

7

Monitor Out jacks [MON OUT L, R] (RCA pin) Stereo Out jacks [ST. OUT L, R] (RCA pin) AUX Send jacks 1, 2 [AUX SEND 1, 2] (Phone) AUX Return jacks 1, 2 [AUX RTN 1, 2] (Phone) Insert jacks 3, 4 [INSERT 3, 4] (TRS Phone) Balanced input connectors 3, 4 [INPUT 3, 4] (Balanced XLR) 7. Recorder in jacks L, R [RECORDER IN L, R] (RCA pin)

MIDI OUT jack [MIDI OUT] (DIN 5-pin) MIDI IN jack [MIDI IN] (DIN 5-pin) Punch in/out jack [PUNCH IN/OUT] (Phone) Data output jack [DATA OUT] (OPTICAL) Data input jack [DATA IN] (OPTICAL) SCSI connector [SCSI] (D-SUB 25-pin) Power cable Power switch [POWER]

10

FD-4

3. SOFTWARE UPDATE
The FD-4 software can be updated through SCSI port. This means that unscrewing and opening up the FD-4 top panel is not necessary to change the EPROMs on the MAIN PCB assy. Please refer to the following explanation for correct software updating procedures.

3-1. Method of Sending Software from Fostex Japan
There are two ways of sending the FD-4 updated software. 1. Updated software in a removable media (e.g. floppy disk, zip disk, etc.) to be sent via airmail 2. Updated software as an attachment file to be sent via E-mail

3-2. Required Tools
The following tools/equipment are required to update the FD-4 software. 1. 2. 3. 4. IBM PC compatible computer with SCSI board Removable type SCSI drive Cable between the removable type SCSI drive and the SCSI board Cable between the removable type SCSI drive and the FD-4 (D-SUB 25-pin)

3-3. Software Updating Procedures
Presuming that the updated software is correctly sent and is copied into your computer. 1. 2. 3. 4. 5. 6. 7. Connect the removable type SCSI drive to the SCSI board. Insert the diskette to the removable type SCSI drive and format it by the computer (IBM PC format). Copy the updated software file to the removable type SCSI drive (diskette). Reconnect the removable type SCSI drive to the FD-4 SCSI port. In order to boot up the FD-4 system software, insert the diskette formatted by the FD-4. Eject the diskette by pressing the EXIT/NO key while holding down the SHIFT key. Insert the diskette with updated software file. The FD-4 LCD display shows "No Disk", "Initial..", "name of drive (e.g. ZIP 100)" and "FD4MOT" in order and comes to a standstill at the display below.
: Blinking

DIGITAL

SURE ?
SYNC OUT AUTO DRIVE SCSI A.PUNCH

8. Pressing the EXECUTE/YES key would update the software. The display shows "Loading!", "Writing!" and "Initial.." in order and automatically returns to the above condition again. This indicates that updating the software is completed. 9. Eject the diskette with updated software file and insert the diskette formatted by the FD-4. 10. Check the software version by the Service Mode. (For details, please refer to the section "4-2. Software/CPU version".)

CAUTION:
1. The diskette in which the updated software file is copied must be formatted by IBM PC computer, not by Macintosh. 2. If something wrong happens while updating the software (e.g. A blackout occurred while updating the software.), the FD-4 might not be able to boot up the system software inside the Flash ROM. In this case, please refer to the section "48. Flash ROM" (page 17).

11

FD-4

4. SERVICE MODE
There are various optional modes available in the FD-4 Service Mode. Please utilize them when servicing the unit.

4-1. Putting FD-4 into Service Mode
The way of putting the FD-4 into Service Mode is as follow. 1) Connect a SCSI device, insert the diskette formatted by the FD-4 and turn it on. 2) Turn on the power of FD-4. 3) While holding down the STOP button and SHIFT key, press the SETUP key. As shown below, by rotating the jog dial C.W. or C.C.W., various optional modes will be displayed in addition to the general SETUP menus. In order to select a certain optional mode, press the EXECUTE/YES key while its menu is displayed.

Format? Save PGM? Load PGM? DeviceID? Resolu? N/A Freeblock? Digi.out?
C.W. C.W. C.W.

Sign.Set? TempoSet? Version? DA Test?
C.W.

TitleEdit? Del. PGM? Click ? Disp.Test? SelfCheck? OfsetDisp? Preroll? SyncOut? FrameRate? MtcOffset?
: Service Mode N/A: Not Available

N/A

N/A
C.W.

Digi.in? RecProtct?

NOsEvent?

C.W.

C.W.

FlashROM? Init.Disk?

SlaveType? SlaveMode?

OfsetMode?

4-2. Flash ROM/CPU version
: Blinking

This mode is used to check the Flash ROM and CPU versions currently installed in the unit. In order to check the version number, press the "EXECUTE/ YES" key while "?" is blinking.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

: Blinking

The example on the left indicates that the Flash ROM version is V1.00 and its programming date is February 28, 1998. In this condition, by turning the jog dial C.W., the CPU version can be checked.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

12

FD-4

: Blinking

The example on the left indicates that the CPU version is V1.00 and its programming date is January 19, 1998.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

4-3. DA Test
: Blinking

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

This mode test the signal flow from the DATA INPUT jack to the D/A converter. A S/P DIF digital signal whose sampling frequency is the same as the one when formatting the diskette (MASTERING MODE 1, 2: 44.1kHz, NORMAL MODE: 32kHz) must be input to the DATA INPUT jack. To execute this test, press the EXECUTE/YES key while "?" is blinking.

: Blinking

DIGITAL

32kHz

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

If the FD-4 is in a normal condition, "32kHz or 44.1kHz" and "DIGITAL" will be lit solid. The odd (1 and 3) and even (2 and 4) channels indicate the L and R input level of S/P DIF digital signal fed to the DATA INPUT jack respectively. If the FD-4 is not in a normal condition, "32kHz or 44.1kHz" and "DIGITAL" will blink and the bargraph meter will not indicate any input level.

1

2

3

4

L

R

4-4. Display/Button Test
: Blinking

This mode tests if all the segments on the LCD display and the LEDs on the FD-4 top panel are correctly working or not. To execute this test, press the EXECUTE/YES key while "?" is blinking.

SYNC OUT CLK AUTO PLAY RTN

DRIVE SCSI A.PUNCH RHSL TAKE

MTC MIDI REMAIN LOC MTC ABS IN H BAR M

DIGITAL SLAVE

32kHz 44.1kHz 48kHz SETUP MTC OFFSET
CLK MB SF F % DF

If the FD-4 is in a normal condition, all the segments on the LCD display will lit solid and the LEDs on the top panel will start blinking. If the FD-4 is not in a normal condition, the faulty segments on the LCD display and/or LEDs on the top panel will remain unlit.

S

VARI PITCH TEMPO PGM

SURE ?
SYNC OUT CLK MTC AUTO PLAY RTN

COMPLETED!
DRIVE IDE SCSI A.PUNCH RHSL TAKE

13

FD-4

In this condition, if the EXECUTE/YES key is pressed one more time, the Button Test can be executed. The Button Test checks if each key/button and jog dial are working properly or not. The display on the left indicates that the RECORD button is pressed. ("K" stands for the Key and "J" the Jog dial.)

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

The display on the left indicates that the jog dial is turned C.W. The table below shows the relationship between the key/ button/jog dial and the corresponding numbers appear on the LCD display. In order to quit the Button Test, turn the jog dial C.W. or C.C.W. further after "J 020" or "J-19" is displayed respectively. Key/Button/Jog Dial RECORD STOP PLAY REWIND/ F FWD/ SHIFT VARI PITCH/ P.EDIT AUTO RTN/PLAY LOCATE/ LOC MEM HOLD/ STORE No. K01 K02 K03 K04 K05 K06 K07 K08 K09 K10 K11 Key/Button/Jog Dial EDIT UNDO/REDO EXECUTE/YES EXIT/NO/ EJECT AUTO RTN START AUTO PUNCH IN AUTO PUNCH OUT AUTO RTN END CLIPBOARD IN CLIPBOARD OUT DISP SEL No. K12 K13 K14 K15 K16 K17 K18 K19 K20 K21 K22 Key/Button/Jog Dial SETUP TIME BASE SEL RECORD TRACK 1/L RECORD TRACK 2/R RECORD TRACK 3/L RECORD TRACK 4/R RECORD TRACK 5/L RECORD TRACK 6/R JOG DIAL (C.W.) JOG DIAL (C.C.W.) No. K23 K24 K25 K25 K25 K25 K25 K25 J 00 ~ 20 J -00 ~ -19

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

4-5. Self Check
: Blinking

This mode automatically tests the following points in order. · SCSI bus · ATA bus · MIDI in/out circuit · S/P DIF digital signal (44.1kHz) · 32kHz digital signal · Vari-pitch circuit · A/D and D/A circuit (Input Monitor)

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

14

FD-4

INPUT 4 INPUT 3 AUX RTN 2 MONO/L

R MON OUT L

R

ST OUT

L

2

AUX SEND

1

R

R

AUX RTN 1 MONO/L

4

INSERT

3

POWER

SCSI

DATA IN

DATA OUT

PUNCH IN/OUT

MIDI IN

MIDI OUT

RECORDER IN R L

External SCSI Drive

Optical Cable

MIDI cable

Apply audio signal.

To start the Self Check mode, press the EXECUTE/YES key when "?" is blinking (condition indicated in the previous page). As shown in the left, "SelfCheck", "Initial..", name of connected SCSI drive (The example in the left shows that the ZIP drive is connected to the FD-4 SCSI port.) and "ATA Bus C (Check)" appear on the FD-4 LCD display in order. Since a 2.5" internal E-IDE hard disk drive is not installed in the FD-4, the Self Check mode comes to a standstill at "ATA Bus Check" test.
SYNC OUT CLK AUTO DRIVE SCSI A.PUNCH

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

In order to continue the Self Check mode, press the EXECUTE/YES key. If the FD-4 is in a good shape, "Check OK!" will be displayed and the FD-4 is automatically put into Input Monitor mode with all the RECORD TRACK LEDs and RECORD LED flashing after checking the points mentioned in the previous page. In this condition, if a signal is applied to the FD-4 RECORDER IN (L, R) jacks, its level can be monitored on the bargraph level meter. To quit the Self Check mode, press the EXIT/NO key when "Check OK!" is displayed.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

1

2

3

4

L

R

15

FD-4

The followings are examples of error message when the FD-4 is not working properly.

· SCSI function

· MIDI function

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

· Digital Signal in/out (Fs: 44.1kHz)
44.1kHz

· Digital Signal in/out (Fs: 32kHz)

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

· Vari-pitch function

VARI PITCH
SYNC OUT CLK AUTO DRIVE SCSI A.PUNCH

4-6. Offset Display
: Blinking

This mode determines if the offset value against a master machine should be displayed or not when the FD-4 is working as a slave machine. If you would like to turn ON the offset display, press the EXECUTE/YES key while "?" is blinking. (The default setting is "off".) Then, turn the jog dial C.W and press the EXECUTE/YES key. In order to display the offset value, select the "MTC" by the TIME BASE key and the "REMAINING TIME" as DISP SEL key. CAUTION: 1. There might be a case that the percentage display does not indicate "0.0%" exactly when the FD-4 is working as a slave machine and is synchronizing with a master machine. This is caused by a difference of internal clock between both machines but there is nothing wrong with it. 2. The two-digit numbers displayed in the right of percentage display ("05" in the left example) is only for software programming purpose.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

OFFSET
H M S DF SF

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

16

FD-4

4-7. Initializing Disk
This mode initializes an external SCSI device connected to the SCSI port or a 2.5" internal E-IDE hard disk drive. The disk drive currently connected can be initialized. After pressing the EXECUTE/YES key, "SURE?" will start blinking in the LCD display. In this condition, pressing the EXECUTE/YES key one more time would initialize the selected disk drive. This mode puts the disk back to the condition originally formatted and is equal to "Quick Format".

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

4-8. Flash ROM
: Blinking

This mode is used when copying the system software from EPROMs to Flash ROM. As mentioned in the section "SOFTWARE UPDATE", the FD-4 software inside the Flash ROM can be updated through SCSI port. However, if something wrong happens when updating the software (e.g. A blackout occurred while updating the software.), the FD-4 might not be able to boot up the system software inside the Flash ROM.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

In this case, the following procedures must be taken. 1. 2. 3. 4. Turn the switch S1 on the MAIN PCB assy to "EPROM" side. Mount and solder the EPROM sockets to "U31" and "U32" on the MAIN PCB assy. Plug the EPROMs into the sockets. Turn on the power of FD-4.

In this condition, the FD-4 is booted up using the system software inside the EPROMs. The next procedures to take are as follows. 1. Put the FD-4 into the Service Mode, select "FlashROM" and press EXECUTE/YES key. ("SURE?" is blinking.) 2. Press the EXECUTE/YES key one more time to copy the system software from EPROMs to Flash ROM. 3. Turn the switch S1 to "FLMEM" side. 4. In order to confirm that the FD-4 is booted up using the system software inside the Flash ROM, turn off the power, disconnect the EPROMs and turn the power back on again. 5. After the confirmation, update the system software inside the Flash ROM through SCSI port again.

4-9. Event Number
Individual Audio Files are continuously recorded in each track of program on the FD-4. However, the FD-4 disk management system allows to create a "no signal recorded" section between Audio Files. This "no signal recorded" section is handled as "Zero File". As shown in the diagram below, Audio Files and Zero Files will be alternately recorded on the FD-4 and each Audio File and Zero File are counted as individual "Event". Thus, the number of events on a certain track is calculated by summing up these Audio Files and Zero Files. Each track can accommodate up to 512 events but the FD-4 will not newly record events when the number of events reach 508.
: Recorded part (shortest length: 740msec, Fs=44.1kHz)

ABS 0

: Non-recorded part (shortest length: 740msec, Fs=44.1kHz)

ABS END

ABS 23h 59m

Audio File 1

Zero File 1

Audio File 2

Zero File 2

Audio File 3

Event No.

1

2

3

4

5

17

FD-4

: Blinking

SETUP

This Service Mode allows to check the Event Number recorded on each track in one program on the FD-4. In order to check, press the EXECUTE/YES key while "?" is blinking.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

The example in the left indicates that there are 3 events created on track 1. By turning the jog dial C.W., you can check the event number on track 2, 3, 4...
SETUP

SYNC OUT CLK MTC AUTO PLAY RTN

DRIVE IDE SCSI A.PUNCH RHSL TAKE

CAUTION: If a long recording and/or many editing is committed, the Event Number increases. If the Event Number is getting closer to its maximum limit (508), please save/load the data to/from an external DAT recorder or SCSI device. During save/load procedures, Audio Files can be optimized and as a result, the Event Number decreases.

4-10. Free Block Check
: Blinking

This mode is used to check the condition of the diskette inserted into an external SCSI drive connected to the FD-4. If the Free Block indicates a large number even after formatting the diskette and no signal is recorded, the diskette can be judged to be in a bad condition.

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

SYNC OUT CLK AUTO

DRIVE SCSI A.PUNCH

18

FD-4

5. ERROR CODE LIST
The chart below indicates the error code number and corresponding description. Since the error code list is basically designed for our engineers to improve the software, the description is quite technical. If you find the FD-4 with one of the error codes displayed, we encourage you to update the software first. In case updating the software does not solve the problem, we would like you to inform us about details.

FD-4 ERROR CODE LIST
ERROR CODE
1 3 9 10 11 12 14 15 16 20 21 22 30 31 32 35 36 38 40 41 42 45 52 60 61 62 63 64 96 97 99

DESCRIPTION
Audio File address breaks into System File. SCSI drive does not boot up correctly when in SCSI access operation. When saving system region sector, its address is registered in Free_block File during Free block File checking procedure. Link_pointer which links Audio File indicates smaller address (out of region) than Link_File address region in RAM. Link_pointer indicates larger address (out of region) than Link_File address region in RAM. "Pointer_addre" calculation of Link_Pointer is not correct. Link_Pointer during recording/reproducing indicates smaller address (out of region) than actual Link_File address region. Link_Pointer during recording/reproducing indicates larger address (out of region) than actual Link_File address region. "Pointer_addre" calculation of Link_Pointer during recording/reproducing is not correct. src_cash_load: Improper access of link address occurred while PASTE editing. bak_cash_load: Program link during PASTE/MOVE editing is incorrect. bak_cash_load: Imcompatibility problem occurred on program link during PASTE/MOVE editing. Error when executing MOVE editing. Improper Link Pointer. Error in "bak_cash_load" function. Error when executing MOVE editing. Improper Link Pointer. Error in "bak_cash_load" function. Error when executing MOVE editing. Improper Link Pointer. Error in "bak_cash_load" function. Backup_Save:Error occurred when saving data to SCSI device. Backup_Load: Error occurred when loading data from SCSI device. Displayed in Test Mode only. SCSI device cannot be recognized during initial test. dis_cah_load: Improper access occurred when recording/reproducing. dis_cah_load: Improper access occurred when recording/reproducing. dis_cah_load: Improper access occurred when recording/reproducing. get_non_des_block: Remaining disk capacity is insufficient. non_des_cash_save_sub: Improper access occurred when recording/reproducing. remake_free_block: There was improper access to program management region. remake_free_block: There was improper access to program management region. remake_free_block: Number of manageable events exceeds limit. remake_free_block: There was improper access to program management region. remake_free_block: There is an overlapping section in program management region. There was improper access to program management region. There was improper access to program management region when saving System File. There was improper access when fading in/out.

19

FD-4

6. INSTALLING 2.5" INTERNAL HARD DISK DRIVE
The Model 9045 and a 2.5" E-IDE hard disk drive installing procedures are explained below.

Model 9045 Contents
· Bracket, HD, FD-4 (P/N: 8221234000) x 2 · Connector, PI, header, 50P, AMPMOD (P/N: 8245314000) x 1 · Cable, flat, 2P, L150 (P/N: 8276292015) x 1 · Cable assy, flat, 50P, P1.0, AMPMOD, L150 (P/N: 8277465015) x 1 · 14 x screws (P 3 x 4 CZn)

Installing Procedures
1) Loosen 14 x screws (BBT 3 x 8 BZn) which fix the FD-4 Top Panel section to the Bottom Panel section. 2) Remove the following cables from the connectors on the MAIN PCB assy. · 9-pin cable to the J3 (coming from MIXER A PCB assy) · 9-pin cable to the J7 (coming from DISPLAY PCB assy) · 7-pin cable to the J10 (coming from MIXER A PCB assy)
Top Panel section

MAIN PCB assy Bottom Panel section

7- J10 pin 9- J3 pin 9- J7 pin

BBT 3x8 BZn

BBT 3x8 BZn

20

FD-4

3) Remove the MAIN PCB assy by loosening the following screws. · 5 x screws (B 3 x 6 CZn) fixing the PCB assy from top · 6 x screws (BBT 3x8 BZn) fixing the PCB from rear · 2 x Fix-Stand fixing the D-SUB 25-pin connector 4) Mount and solder the 50-pin connector and 2-pin cable. (Before soldering, you might need to remove the soldering by a solder remover.)

Cable, flat, 2P, L150

Connector, PI, header, 50P, AMPMOD

nl E ar ge d w ie V of M IN A C P B as sy
B 3 x 6 CZn

M A IN P C B
BBT 3 x 8 BZn

as sy
Fix-Stand

21

FD-4

5) Put back the MAIN PCB assy to the Bottom Panel section by tightening the following screws. · 5 x screws (B 3 x 6 CZn) fixing the PCB assy from top · 6 x screws (BBT 3x8 BZn) fixing the PCB from rear · 2 x Fix-Stand fixing the D-SUB 25-pin connector 6) Using 4 x screws (P 3 x 4 CZn), fix the HD Bracket to a 2.5" E-IDE hard disk drive. 7) Using 4 x screws (P 3 x 4 CZn), fix the 2.5" E-IDE hard disk drive/HD bracket to the Bottom Panel section. (During the above procedures 6) and 7), adjust the tightening position of screws to the HDD and to the bottom panel so that screws are not bothered from each other.)
B 3 x 4 CZn

B 3 x 4 CZn

B3x6 CZn

ve E Dri -ID k E is 5" D 2. ard H
B 3 x 4 CZn
1 2 49 50

Bracket, HD, FD-4 B 3 x 4 CZn

BBT 3 x 8 BZn

Fix-Stand

M A IN C P B as sy

22

FD-4

8) Connect the 50-pin flat cable between J12 of MAIN PCB assy and the HDD connectors. When connecting, in order to connect pins straight, do not twist or turn the cable. (Pin-1 of J12 (RED) must go to Pin-1 of HDD connectors.) 9) Connect the following cables from the connectors on the MAIN PCB assy. · 9-pin cable to the J3 (coming from MIXER A PCB assy) · 9-pin cable to the J7 (coming from DISPLAY PCB assy) · 7-pin cable to the J10 (coming from MIXER A PCB assy) 10) Tighten 14 x screws (BBT 3 x 8 BZn) which fix the FD-4 Top Panel section to the Bottom Panel section.

7- J10 pin 9- J3 pin

RED 9- J7
pin

Cable assy, flat, 50P, P1.0, AMPMOD, L150

BBT 3 x 8 BZn

BBT 3 x 8 BZn

23

FD-4

7. EXPLODED VIEW, PCB ASSEMBLY AND PARTS LIST
FD-4 OVERALL EXPLODED VIEW & PARTS LIST
Ref. No. 1 2 3 4 5 6 7 8 9 10 ! 11 12 13 14 15 16 17 18 19 20 ! 21 Part No. 8212 6100 00 8212 6090 00 8221 2290 00 8274 1240 00 8216 6641 00 8226 2370 00 8274 1220 00 8226 2230 01 8274 1360 00 8274 1370 00 8274 1380 00 8204 0820 00 8221 2270 00 8274 1230 00 8226 2380 00 8216 6670 00 8226 1601 03 8226 2390 01 8207 0005 00 8207 0120 00 8276 8351 00 8276 0030 00 8276 0060 00 8276 8790 00 22 23 24 25 26 27 28 29 30 31 8207 0084 00 8207 0084 01 8253 4620 01 8216 6650 00 8216 6361 00 8242 2340 13 8276 9140 06 8276 8720 14 8276 3750 09 8207 0117 01 8277 3530 15 Description Window, LCD, FD-4 Panel, top, FD-4 Panel, bottom, FD-4 PCB assy, XLR, FD-4 Shield, mixer, FD-4 Button assy, control, FD-4 PCB assy, Mixer A, FD-4 Knob, volume, C PCB assy, Display, FD-4 PCB assy, Main, FD-4 PCB assy, Power, FD-4 Plate, mounting, B Bracket, jack, FD-4 PCB assy, Jack, FD-4 Knob, jog, FD-4 Sheet, jog, FD-4 Knob, slide, N4.5 Knob, fader, N4.5 Cord, holder Foot, FF-822 Cord, power, CSA, non integral, USA/CND Cord, power, JPN Cord, power, EUR Cord, power, BS, 2C, PHE-8, UK Bushing, 2271 (Except CND) Bushing, 3P31, CND SW, P, Power, SDDJF1-A-2 Sheet, isolation, power, FD-4 Cushion, battery, PD-4/FD-4 Filter, EMI, ferrite, core, HF70RH16x28x10 Tube, UL, black, L60 Tube, UL, clear, 16, L140 Cable assy, earth lug, D3, L90 Cord holder, CS-1 Cable assy, earth lug, D3-D3, #20, L150 Ref. No. 32
! !

33 34 35

Part No. Description 8277 3530 20 Cable assy, earth lug, D3-D3, #20, L200 8274 1390 00 PCB assy, AC In, FD-4 8239 0007 08 Fuse, 20, TDLY, 0.8A, 250V 8216 6361 01 Cushion, button, FD-4

24

FD-4

FD-4 OVERALL EXPLODED VIEW

25

26

FD-4

FD-4 PCB PATTERN DRAWING
· Parts Side of MAIN PCB assy

· Foil Side of MAIN PCB assy

FD-4

27

FD-4

· MIXER A, JACK and XLR PCB assys

28

FD-4

· DISPLAY PCB assy

29

30

FD-4

· POWER and AC IN PCB assys

FD-4

FD-4 Parts List
· MAIN PCB assy
Ref. No. B001 Part No. Description 8274 1370 00 PCB Assy, Main, FD-4 8251 5191 00 Plain PCB, Main, FD-4 ICs Description ST, analog, regulator, NJM78M05DLA N/A QFP, digital, gate array, ASPI ST, digital, 74HCU04 QFP, digital, SCSI, M86604L SOP, digital, SCSI, term, BH9595FP-Y ST, digital, VCO, TC9246F Opt., photo coupler, PC900 ST, digital, 74HC14 ST, analog, reset, NJM2103M ST, digital, driver, DTC114EK QFP, digital, CPU, main, FD-4, mask, SH7042, F28 N/A ST, digital, driver, DTA114EK ST, digital, 74HC32 N/A ST, digital, 74HC157 TSOP, digital, Flash ROM, M29F400T90, SGS N/A SOJ, digital, DRAM, HM5118160AJ-7 N/A ST, analog, op amp, NJM2115M (TEI) ST, digital, AD, AK5351 ST, digital, DA, AK4321 N/A ST, analog, NJM4560M N/A ST, digital, driver, DTC114EK ST, digital, driver, DTA114EK ST, digital, 74HC04 Ref. No. R001, 002 R003, 004 R005~007 R008 R009 R010 R011 R012 R013 R014 R015 R016 R017 R018 R019 R020 R021~25 R026, 027 R028 R029 R030 R031 R032 R033 R034 R035 R036 R037, 038 R039 R040 R041 R042 R043, 044 R045~048 R049 R050 R051 R052 R053, 054 R061 R062~065 R066 R067 R068 R069 R070 R071 RESISTORs Part No. Description 8230 5001 01 ST, carbon, 1/10W, 100, 5% N/A 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5005 62 ST, carbon, 1/10W, 5.6k, 5% 8230 5003 32 ST, carbon, 1/10W, 3.3k, 5% 8230 5002 22 ST, carbon, 1/10W, 2.2k, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5001 05 ST, carbon, 1/10W, 1M, 5% 8230 5000 00 ST, carbon, 1/10W, 0, 5% 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5001 05 ST, carbon, 1/10W, 1M, 5% 8230 5000 00 ST, carbon, 1/10W, 0, 5% 8230 5004 72 ST, carbon, 1/10W, 4.7k, 5% N/A 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5000 00 ST, carbon, 1/10W, 0, 5% N/A 8230 5004 72 ST, carbon, 1/10W, 4.7k, 5% 8230 5001 52 ST, carbon, 1/10W, 1.5k, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5002 24 ST, carbon, 1/10W, 220k, 5% N/A 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5007 51 ST, carbon, 1/10W, 750, 5% 8230 5001 04 ST, carbon, 1/10W, 100k, 5% 8230 5007 51 ST, carbon, 1/10W, 750, 5% 8230 5002 03 ST, carbon, 1/10W, 20k, 5% 8230 5001 22 ST, carbon, 1/10W, 1.2k, 5% 8230 5005 61 ST, carbon, 1/10W, 560, 5% 8230 5001 22 ST, carbon, 1/10W, 1.2k, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5001 02 ST, carbon, 1/10W, 1k, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% N/A N/A 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5001 52 ST, carbon, 1/10W, 1.5k, 5% N/A 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5002 22 ST, carbon, 1/10W, 2.2k, 5% 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 31

Ref. No. U001, 002 U003, 004 U005 U006 U007 U008 U009, 010 U011 U012 U013 U014 U015 U016~019 U020~023 U024 U025~028 U029 U030 U031, 032 U033 U034, 035 U101, 201 U151 U152, 252 U352, 452 U153, 253 U353, 453 U901, 902 U903 U904

Part No. 8236 5403 01

8236 0818 00 8236 5610 04 8236 0828 00 8236 0829 00 8236 5034 00 8234 0199 00 8236 5600 14 8236 5025 00 8236 5701 01 8236 0838 01

8236 5704 01 8236 5600 32 8236 5601 57 8236 0840 11

8236 0831 00

8236 5050 11 8236 5407 00 8236 5408 00 8236 7207 00 8236 5701 01 8236 5704 01 8236 5600 04

Ref. No. D001 D002 D003~006 D007

DIODEs Part No. Description 8234 1050 00 VF, SCHOTTKY, EK13 N/A 8234 5028 00 ST, DAN202K 8234 7506 00 ST, RB400D

FD-4

Ref. No. R072 R073 R074~076 R077 R078 R079~082 R083~086 R087 R088~090 R091 R092~094 R095, 096 R097 R098, 099 R151 R152 R101, 201 R102, 202 R103, 203 R104, 204 R105, 205 R106, 206 R107, 207 R108, 208 R109, 209 R111~411 R511~811 R112~412 R512~812 R113~413 R513~813 R114~414 R514~814 R161, 261 R361, 461 R901 R902 R903 R904, 905 R906, 907 R908, 909 R910, 911 R912 R913

RESISTORs Description N/A 8230 5000 00 ST, carbon, 1/10W, 0, 5% 8230 5002 21 ST, carbon, 1/10W, 220, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% N/A 8230 5001 03 ST, carbon, 1/10W, 10k, 5% N/A 8230 5001 03 ST, carbon, 1/10W, 10k, 5% N/A 8230 5001 02 ST, carbon, 1/10W, 1k, 5% 8230 5001 05 ST, carbon, 1/10W, 1M, 5% N/A 8230 5001 00 ST, carbon, 1/10W, 10, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5002 03 ST, carbon, 1/10W, 20k, 5% 8230 5001 23 ST, carbon, 1/10W, 12k, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5003 31 ST, carbon, 1/10W, 330, 5% 8230 5003 31 ST, carbon, 1/10W, 330, 5% N/A N/A 8230 5001 04 ST, carbon, 1/10W, 100k, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% N/A 8230 5001 03 ST, carbon, 1/10W, 10k, 5% N/A 8230 5002 72 ST, carbon, 1/10W, 2.7k, 5% N/A 8230 5001 04 ST, carbon, 1/10W, 100k, 5% N/A 8230 5001 00 ST, carbon, 1/10W, 10, 5% N/A N/A 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5002 21 ST, carbon, 1/10W, 220, 5% 8230 5001 01 ST, carbon, 1/10W, 100, 5% 8230 5001 03 ST, carbon, 1/10W, 10k, 5% 8230 5001 02 ST, carbon, 1/10W, 1k, 5% N/A 8230 5001 03 ST, carbon, 1/10W, 10k, 5% N/A Part No.

Ref. No. C001 C002 C003 C004 C005~007 C008 C009, 010 C011 C012, 013 C014 C015 C016, 017 C018 C019 C020 C021 C022~025 C026 C027 C028 C029 C030 C031, 032 C033, 034 C035, 036 C037~040

CAPACITORs ALU = Electrolytic type CER = Ceramic type Part No. Description N/A 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F N/A 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F N/A 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F N/A 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F N/A 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5004 71 ST, CER, 50V, 470pF, 5%, CC20SL 8233 5001 01 ST, CER, 50V, 100pF, 5%, CC20SL N/A 8233 5004 71 ST, CER, 50V, 470pF, 5%, CC20SL 8233 5002 20 ST, CER, 50V, 22pF, 5%, CC20SL 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8233 5002 20 ST, CER, 50V, 22pF, 5%, CC20SL 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R

32

FD-4

Ref. No. C041~045 C046 C047 C048 C049~051 C052 C053~056 C057 C058 C059 C060 C061, 062 C063 C064 C065 C066 C067 C068~070 C071 C072 C073 C074, 075 C076 C077 C078 C079~087

Part No. 8232 1431 06 8233 5021 04 8232 1431 06 8233 5041 03 8233 5001 50

8233 5041 03 8233 5094 74 8232 1431 06 8233 5021 04 8233 5041 03 8232 1431 06 8233 5002 21 8233 5044 73 8233 5041 03 8233 5001 21 8233 5021 04 8233 5041 03 8232 1461 05 8233 5041 03 8233 5003 30 8233 5041 03 8233 5001 01 8233 5004 71

Description N/A VT, ALU, 16V, 10µF, 20%, SME-VB ST, CER, 50V, 0.1µF, +80, CC20F VT, ALU, 16V, 10µF, 20%, SME-VB ST, CER, 25V, 0.01µF, 10%, CC20R ST, CER, 50V, 15pF, 5%, CC20SL N/A ST, CER, 25V, 0.01µF, 10%, CC20R ST, CER, 25V, 0.47µF, 20%, KC30E VT, ALU, 16V, 10µF, 20%, SME-VB ST, CER, 50V, 0.1µF, +80, CC20F ST, CER, 25V, 0.01µF, 10%, CC20R VT, ALU, 16V, 10µF, 20%, SME-VB ST, CER, 50V, 220pF, 5%, CC20SL ST, CER, 25V, 0.047µF, 10%, CC20R ST, CER, 25V, 0.01µF, 10%, CC20R ST, CER, 50V, 120pF, 5%, CC20SL ST, CER, 50V, 0.1µF, +80, CC20F ST, CER, 25V, 0.01µF, 10%, CC20R VT, ALU, 50V, 1µF, 20%, SME-VB ST, CER, 25V, 0.01µF, 10%, CC20R ST, CER, 50V, 33pF, 5%, CC20SL ST, CER, 25V, 0.01µF, 10%, CC20R ST, CER, 50V, 100pF, 5%, CC20SL ST, CER, 50V, 470pF, 5%, CC20SL N/A

Ref. No. C088 C089, 090 C091 C092 C093, 094 C095 C096~100 C101~104 C151 C152 C153 C154 C155 C156 C157 C158, 159 C101, 201 C102, 202 C103, 203 C104, 204 C105, 205 C106, 206 C107, 207 C108, 208 C111~411 C511~811 C112~412 C512~812 C113, 213 C313, 413 C114, 214

Part No. Description 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F N/A 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB N/A 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8233 5001 01 ST, CER, 50V, 100pF, 5%, CC20SL 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R N/A N/A 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8233 5021 04 ST, CER, 50V, 0.1µF, +80, CC20F 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R N/A 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8233 5001 52 ST, CER, 50V, 0.0015µF, 5%, CC20R 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 8276 0020 02 Wire, jumper, IPS-1041-2, F5 8276 0020 02 Wire, jumper, IPS-1041-2, F5 N/A N/A 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB N/A 8233 5006 81 ST, CER, 50V, 680pF, 5%, CC20SL N/A 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R N/A 8233 5041 03 ST, CER, 25V, 0.01µF, 10%, CC20R 33

FD-4

Ref. No. C314, 414 C115~815 C116~416 C516~816 C161~461 C162, 262 C362, 462 C163, 263 C363, 463 C164, 264 C364, 464 C165, 265 C166, 266 C366, 466 C167, 267 C367, 467 C901, 902 C903 C904 C905 C906 C907, 908 C909 C910 C911 C912 C913

Part No.

8232 1434 76

8233 5041 03

8232 1434 76

8233 5041 03

8232 1431 06

8233 5041 03

8233 5041 03 8232 1431 06 8233 5041 03 8233 5021 04

8233 5041 03

8230 5000 00 8233 5003 30 8232 1441 07

Description N/A N/A VT, ALU, 16V, 47µF, 20%, SME-VB N/A N/A ST, CER, 25V, 0.01µF, 10%, CC20R N/A VT, ALU, 16V, 47µF, 20%, SME-VB N/A ST, CER, 25V, 0.01µF, 10%, CC20R N/A N/A VT, ALU, 16V, 10µF, 20%, SME-VB N/A ST, CER, 25V, 0.01µF, 10%, CC20R N/A N/A ST, CER, 25V, 0.01µF, 10%, CC20R VT, ALU, 16V, 10µF, 20%, SME-VB ST, CER, 25V, 0.01µF, 10%, CC20R ST, CER, 50V, 0.1µF, +80, CC20F N/A ST, CER, 25V, 0.01µF, 10%, CC20R N/A Resistor, ST, carbon, 1/10W, 0, 5% ST, CER, 50V, 33pF, 5%, CC20SL VT, ALU, 25V, 100µF, 20%, SME-VB

Ref. No. J004 J005 J006 J007 J008 J009 J010 J011, 012 J101, 201 L001~003 L004 L005 L006 L007, 008 L009 L010, 011 L012 L013, 014 L015, 016 L017~021 L022 L101~201 L102~402 L502~802 L103~403 L503~803 S001 X001 X002 X003 X004

Ref. No. E1401 E1402 J001, 002 J003

MISCELLANEOUS Part No. Description 8245 1580 11 Connector, PI, socket, IC, 32P N/A N/A 8245 1711 09 Connector, PI, jack, 8283, 9P, WHT

Part No. Description 8245 3170 00 Connector, opt., TX178 8245 3180 00 Connector, opt., RX178 8245 3120 05 Connector, PL, jack, D-SUB, 25P, 70057-025, EMIFIL 8245 1711 09 Connector, PI, jack, 8283, 9P, WHT 8245 2980 00 Connector, PL, jack, phone, LGR4609-7000 8245 4200 00 Connector, jack, DIN5P, YKF51-5053 8245 1711 07 Connector, PI, jack, 8283, 7P, WHT N/A 8245 2850 00 Connector, PL, jack, RCA, 1P, YKB11-0923, W/S 8276 9130 00 Wire, jumper, isolation, 1/4 type 8242 1962 23 Coil, PVT, 22µH, LF5.0S N/A 8242 1962 23 Coil, PVT, 22µH, LF5.0S 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T N/A 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T N/A 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T N/A 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T N/A 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T N/A 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T N/A 8253 4570 02 Switch, slide, 1-2, nonshortening, SSSS91 8256 1700 01 Resonator, ST, XTL, 22.579 MHZ, FUP-FBB3AFUJICOM 8256 1700 03 Resonator, ST, XTL, 16.384MHz, FUP-FBB3A 8256 1790 01 Resonator, PT, CER, 7.000MHz, F5, EFOEN N/A

34

FD-4

Ref. No. Part No. Y3301 8216 5950 00 Y3302 W001, 002 W003 8276 7320 30

Description Shield, RCA N/A N/A Cable assy, 8P, 8263WHT5395, #22, L300 W004~008 N/A W101, 201 N/A W102, 202 8230 5000 00 Resistor, ST, carbon, 1/10W, 0, 5%

· MIXER A PCB assy
Ref. No. B001 Part No. Description 8274 1220 00 PCB Assy, Mixer A, FD-4 8251 9672 01 Plain PCB, Mixer A, FD-4 ICs Description SIP, analog, NJM2068LD SIP, analog, NJM4558L SIP, analog, NJM2068LD SIP, analog, NJM4556AL SIP, analog, NJM4558L SIP, analog, NJM4558L SIP, analog, NJM2068LD SIP, analog, NJM4558L SIP, analog, NJM4558L PT, digital, driver, DTC143TS

Ref. No. U001, 002 U003, 004 U005 U006 U301 U302 U401 U302, 402 U503~803 U510~810

Part No. 8236 0366 00 8236 0342 02 8236 0366 00 8236 0352 03 8236 0342 02 8236 0342 02 8236 0366 00 8236 0342 02 8236 0342 02 8236 0781 07

Ref. No. R001, 002 R010 R011~013 R150, 250 R151, 251 R152, 252 R153, 253 R155, 255 R156, 256 R157, 257 R158, 258 R160, 260 R161, 261 R162, 262 R163, 263

RESISTORs Part No. Description 8230 1504 79 VT, carbon, 1/2W, 4.7, 5% 8240 2540 00 Pot, PI, SL45, 50kAA, NS-4502GVP, L20 8240 2530 00 Pot, PI, RT12, 30kAA, EVJY00, L20 8230 1388 23 HT, carbon, 1/4W, 82k, 5% 8230 1382 03 HT, carbon, 1/4W, 20k, 5% 8230 1384 73 HT, carbon, 1/4W, 47k, 5% 8230 1381 04 HT, carbon, 1/4W, 100k, 5% 8230 1388 23 HT, carbon, 1/4W, 82k, 5% 8230 1381 03 HT, carbon, 1/4W, 10k, 5% 8230 1381 03 HT, carbon, 1/4W, 10k, 5% 8230 1381 03 HT, carbon, 1/4W, 10k, 5% 8230 1388 23 HT, carbon, 1/4W, 82k, 5% 8230 1381 04 HT, carbon, 1/4W, 100k, 5% 8230 1388 23 HT, carbon, 1/4W, 82k, 5% 8230 1382 03 HT, carbon, 1/4W, 20k, 5%

Ref. No. R164, 264 R165, 265 R166, 266 R167, 267 R168, 268 R170, 270 R171, 271 R172, 272 R173, 273 R501, 601 R502, 602 R503, 603 R504, 604 R701, 801 R702, 802 R703, 803 R704, 804 R705, 805 R706, 806 R707, 807 R708, 808 R709, 809 R710, 810 R711, 811 R512~812 R513~813 R514~814 R515~815 R516~816 R517~817 R518~818 R519~819 R520~820 R521~821 R522~822 R523~823 R524~824 R525~825 R526~826 R527~827 R528~828 R529~829 R530~830 R531~831 R532~832 R533~833 R534~834 R535~835 R536~836

Part No. 8230 1382 04 8230 1381 03 8230 1381 03 8230 1382 00 8230 1381 01 8230 1381 01 8230 1382 73 8230 1382 73 8230 1381 04 8230 1381 01 8230 1381 04 8230 1381 01 8230 1381 04 8230 1381 04 8230 1382 04 8230 1382 04 8230 1382 03 8230 1382 03 8230 1382 02 8230 1382 02 8230 1382 04 8230 1382 04 8230 1381 01 8230 1382 02 8230 1382 04 8230 1389 12 8230 1381 03 8230 1381 03 8230 1381 03 8230 1382 02 8230 1382 02 8230 1381 32 8230 1381 32 8230 1389 12 8230 1389 12 8230 1382 73 8230 1382 73 8230 1383 63 8230 1383 63 8230 1382 73 8230 1383 63 8230 1383 63 8230 1382 73 8230 1382 73 8230 1383 63 8230 1383 63 8230 1382 20

Description HT, carbon, 1/4W, 200k, 5% HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 20, 5% N/A HT, carbon, 1/4W, 100, 5% HT, carbon, 1/4W, 100, 5% HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 100k, 5% HT, carbon, 1/4W, 100, 5% HT, carbon, 1/4W, 100k, 5% HT, carbon, 1/4W, 100, 5% HT, carbon, 1/4W, 100k, 5% HT, carbon, 1/4W, 100k, 5% HT, carbon, 1/4W, 200k, 5% HT, carbon, 1/4W, 200k, 5% HT, carbon, 1/4W, 20k, 5% HT, carbon, 1/4W, 20k, 5% HT, carbon, 1/4W, 2k, 5% HT, carbon, 1/4W, 2k, 5% HT, carbon, 1/4W, 200k, 5% HT, carbon, 1/4W, 200k, 5% HT, carbon, 1/4W, 100, 5% HT, carbon, 1/4W, 2k, 5% HT, carbon, 1/4W, 200k, 5% HT, carbon, 1/4W, 9.1k, 5% HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 2k, 5% HT, carbon, 1/4W, 2k, 5% HT, carbon, 1/4W, 1.3k, 5% HT, carbon, 1/4W, 1.3k, 5% HT, carbon, 1/4W, 9.1k, 5% HT, carbon, 1/4W, 9.1k, 5% N/A HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 36k, 5% HT, carbon, 1/4W, 36k, 5% HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 36k, 5% HT, carbon, 1/4W, 36k, 5% HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 27k, 5% HT, carbon, 1/4W, 36k, 5% HT, carbon, 1/4W, 36k, 5% HT, carbon, 1/4W, 22, 5%

35

FD-4

Ref. No. R537~837 R540~840 R541~841 R542~842 R543~843 R544~844 R545~845 R546~846 R547~847 R548~848

Part No. Description 8230 1382 20 HT, carbon, 1/4W, 22, 5% 8240 2500 00 Pot., PI, SL45, 50kA, NS-4502VP, L20 8240 2680 00 Pot., PI, RT09, 10kB, CC, EVUF3A, L20 8240 2700 00 Pot., PI, RT12, 50kCC, EVJY00, L20 8240 2510 00 Pot., PI, RT09, 50kB, CC, EVUF3A, L20 8240 2510 00 Pot., PI, RT09, 50kB, CC, EVUF3A, L20 8240 2510 00 Pot., PI, RT09, 50kB, CC, EVUF3A, L20 8240 2510 00 Pot., PI, RT09, 50kB, CC, EVUF3A, L20 8240 2490 00 Pot., PI, RT12, 100kB, CC CT, EVJ02J, L20 8240 2830 00 Pot., PI, RT12, 20kB, CC CT, EVJ02J, L20 CAPACITORs ALU = Electrolytic type CER = Ceramic type PES=Mylar type Part No. Description 8232 1431 07 VT, ALU, 16V, 100µF, 20%, SME-VB 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 1432 27 VT, ALU, 16V, 220µF, 20%, SME-VB 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8012 20 VT, CER, 50V, 22pF, 5%, SL 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB

Ref. No. C160, 260 C161, 261 C162, 262 C163, 263 C164, 264 C165, 265 C166, 266 C167, 267 C170, 270 C171, 271 C172, 272 C172, 273 C501, 601 C502, 602 C503, 603 C504, 604 C510~810 C511~811 C512~812 C513~813 C514~814 C515~815 C516~816 C517~817 C518~818 C519~819 C520~820 C521~821 C522~822 C530, 730 C531, 731 C532, 732 C533, 733 C534~834

Ref. No. C001, 002 C003~006 C007, 008 C009 C140, 240 C141, 241 C142, 242 C143, 243 C144, 244 C145, 245 C146, 246 C150, 250 C151, 251 C152, 252 C153, 253 C154, 254 C155, 255

Part No. Description 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8232 1422 27 VT, ALU, 10V, 220µF, 20%, SME-VB 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8014 71 VT, CER, 50V, 470pF, 5%, SL 8232 8014 71 VT, CER, 50V, 470pF, 5%, SL 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 9012 23 VT, PES, 50V, 0.022µF, 5%, AMZ 8232 9011 03 VT, PES, 50V, 0.01µF, 5%, AMZ 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 8011 01 VT, CER, 50V, 100pF, 5%, SL 8232 9016 82 VT, PES, 50V, 0.0068µF, 5%, AMZ 8232 9016 82 VT, PES, 50V, 0.0068µF, 5%, AMZ 8232 9011 53 VT, PES, 50V, 0.015µF, 5%, AMZ 8232 8012 20 VT, CER, 50V, 22pF, 5%, SL 8232 8012 20 VT, CER, 50V, 22pF, 5%, SL 8232 1424 76 VT, ALU, 10V, 47µF, 20%, SME-VB 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF

36

FD-4

Ref. No. C535~835 C701, 801 C702, 802 C703, 803 C704, 804 C705, 805 C706, 806 C707, 807 C708, 808

Part No. 8232 8181 04 8232 8011 01 8232 8011 01 8232 1421 07 8232 1421 07 8232 8011 00 8232 8011 00 8232 1424 76

Description VT, CER, 25V, 0.1µF, +80, YF VT, CER, 50V, 100pF, 5%, SL VT, CER, 50V, 100pF, 5%, SL VT, ALU, 10V, 100µF, 20%, SME-VB VT, ALU, 10V, 100µF, 20%, SME-VB VT, CER, 50V, 10pF, 5%, SL VT, CER, 50V, 10pF, 5%, SL N/A VT, ALU, 10V, 47µF, 20%, SME-VB

· JACK PCB assy
Ref. No. B001 Ref. No. Q001~006 R001~006 R007~012 J010 Part No. Description 8274 1230 00 PCB Assy, JACK, FD-4 8251 9672 02 Plain PCB, JACK, FD-4 Part No. Description 8234 1434 03 Transistor, VT, NPN, 2SC2878A/B 8230 1381 02 Resistor, HT, carbon, 1/4W, 1k, 5% 8230 1381 03 Resistor, HT, carbon, 1/4W, 10k, 5% 8245 1711 08 Connector, PI, jack, 8P, 8283, WHT 8245 1711 09 Connector, PI, jack, 9P, 8283, WHT 8245 2620 01 Connector, PL, jack, RCA, 2P, BLK 8245 2980 00 Connector, PL, jack, phone, LGR4609-7000 N/A Wire, jumper, F5 Wire, jumper, F7.5 Wire, jumper, F10 Wire, jumper, F12.5

Ref. No. E601 E602 E603 J001 J021 J022 J023 J501~801 S001 S701, 801 S502~802 W001 W002 W010 W011 W012

MISCELLANEOUS Part No. Description Wire, jumper, F5 Wire, jumper, F10 Wire, jumper, F15 8245 2980 00 Connector, PL, jack, phone, LGR4609-7000 8245 1711 05 Connector, PI, jack, 8283, 5P, WHT 8245 1711 03 Connector, PI, jack, 8283, 3P, WHT 8245 1712 03 Connector, PI, jack, 8283, 3P, RED 8245 2980 00 Connector, PL, jack, phone, LGR4609-7000 8253 6550 16 SW, PI, slide, 4-3, non-shortening, SSSF0, L09 8253 6550 13 Switch, PI, slide, 2-3, non-shortening, SSSF0, L09 8253 6550 13 Switch, PI, slide, 2-3, non-shortening, SSSF0, L09 8276 7770 20 Cable assy, 7P, WHTMT/F-MT/BS, L200 8276 7790 30 Cable assy, 9P, WHTMT/F-MT/BS, L300 8276 7780 20 Cable assy, 8P, WHTMT/F-MT/BS, L200 8276 7790 20 Cable assy, 9P, WHTMT/F-MT/BS, L200 8277 4530 40 Cable assy, shiled 2C, 6P, WHT8283-9073, L400

J011 J031, 032 J033~040 L001~006 E101 E102 E103 E104

· XLR PCB assy
Ref. No. B001 Ref. No. J001, 002 J003 Part No. Description 8274 1240 00 PCB Assy, XLR, FD-4 8251 9672 03 Plain PCB, XLR, FD-4 Part No. Description 8245 2680 03 Connector, PL, XLR 31, 3P, NC3FAH20 8245 1721 06 Connector, PL, jack, 8283, 6P, WHT

37

FD-4

· DISPLAY PCB assy
Ref. No. B001 Part No. Description 8274 1360 00 PCB Assy, Display, FD-4 8251 5181 00 Plain PCB, Display, FD-4 ICs Part No. Description 8236 0835 01 QFP, digital, CPU, FD4-display N/A 8236 0836 00 QFP, digital, LCD driver, HD44780U 8256 1760 00 Module, display, LCD, FD-4 N/A 8256 1770 00 Module, jog, SIM-026MT TRANSISTORs Part No. Description 8234 1008 02 VT, PNP, 2SA1150Y DIODEs Part No. Description 8234 5007 00 HT, 1SS136 N/A 8234 5007 00 HT, 1SS136 N/A 8234 5007 00 HT, 1SS136 N/A 8234 5007 00 HT, 1SS136 N/A 8234 0100 00 Opt., V, LED, ORG, GL-2HD6 N/A 8234 0100 00 Opt., V, LED, ORG, GL-2HD6 8234 0191 00 Opt., V, LED, GRN, GL-2EG6 N/A 8234 0191 00 Opt., V, LED, GRN, GL-2EG6 N/A RESISTORs Description Wire, jumper, F10 8230 1381 01 HT, carbon, 1/4W, 100, 5% 8230 1381 05 HT, carbon, 1/4W, 1M, 5% 8230 1382 04 HT, carbon, 1/4W, 200k, 5% Wire, jumper, F5 8230 1381 02 HT, carbon, 1/4W, 1k, 5% 8240 1510 04 Pot., PI, RT09, 5kB, L20, 4 knob, RK09K113 8230 1381 04 HT, carbon, 1/4W, 100k, 5% Part No.

Ref. No. U001 U002 U003 U004 U005 U006

Ref. No. R018~019 R020 R021, 022 R023~030 R031~036 R037, 038 R039, 040 R041~043

Part No. 8230 1381 03 8230 1381 04 8230 1381 03 8230 1382 23 8230 1381 11

Description HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 100k, 5% HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 22k, 5% HT, carbon, 1/4W, 110, 5% N/A 8230 1381 02 HT, carbon, 1/4W, 1k, 5% 8230 1388 23 HT, carbon, 1/4W, 82k, 5% CAPACITORs ALU = Electrolytic type CER = Ceramic type Part No. Description 8232 1431 06 VT, ALU, 16V, 10µF, 20%, SME-VB 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 1451 06 VT, ALU, 35V, 10µF, 20%, SME-VB 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF N/A 8232 8014 71 VT, CER, 50V, 470pF, 5%, SL 8232 8063 30 VT, CER, 50V, 33pF, 5%, NPO 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF N/A 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 8031 03 VT, CER, 50V, 0.01µF, +80, YF MISCELLANEOUS Part No. Description N/A Wire, jumper, F5 Wire, jumper, F7.5 Wire, jumper, F10 Wire, jumper, F12.5 Wire, jumper, F20 Wire, jumper, F30 8239 1160 00 Lamp, 5V, 75mA 8253 1350 02 SW, PT, tact, SOR-112HS N/A 8253 1350 02 SW, PT, tact, SOR-112HS N/A 8253 1350 02 SW, PT, tact, SOR-112HS N/A 8253 1350 02 SW, PT, tact, SOR-112HS N/A 8276 7790 55 Cable assy, 9P, WHTMT/F-MT/BS, L550 N/A

Ref. No. C001 C002 C003 C004 C005, 006 C007~009 C010, 011 C012 C013 C014 C015, 016

Ref. No. Q001, 002

Ref. No. D001~008 D007, 008 D009~014 D015, 016 D017, 018 D019, 020 D021~036 D037~040 D041~046 D047, 048 D049 D050, 051 D052 D053, 054 D055, 056

Ref. No. R001 R002~007 R008 R009 R010 R011~015 R016 R017

Ref. No. E101 E501 E502 E503 E504 E505 E506 L001, 002 S001~006 S007, 008 S009~014 S015, 016 S017, 018 S019, 020 S021~036 S037~040 W001 W002

38

FD-4

Ref. No. W003 X001 Y1001 Y1002 Y1003 Y1004 Y1005 Y1006 Y1007 Y1008

Part No. 8256 1340 03 8207 0100 10 8207 0100 11 8207 0100 13 8207 0100 14 8212 6110 00 8207 0100 09 8207 0100 12

Description N/A Resonator, PF, CER, 8.00MHz, F5, EFOEN Spacer, LED, 10 Spacer, LED, 11 Spacer, LED, 13 Spacer, LED, 14 N/A Plate, reflect, LCD, FD-4 Spacer, LED, 9 Spacer, LED, 12

Ref. No. R006 R007 R008, 009

Part No. 8230 1381 03 8230 1384 71 8230 1381 03

Description HT, carbon, 1/4W, 10k, 5% HT, carbon, 1/4W, 470, 5% HT, carbon, 1/4W, 10k, 5%

Ref. No. C001 C002 C003 C004 C005, 006 C007 C008 C009~012 C013 C014 C015, 016 C017~020 C023~026

· POWER PCB assy
Ref. No. Part No. Description 8274 1380 00 PCB Assy, Power Supply, FD-4 8251 9691 01 Plain PCB, Power Supply, FD-4 ICs Description V, analog, power, MIP163 Opt., H, photo coupler, ON3171 220, analog, regulator, 7812FA 220, analog, regulator, NJM7912FA VT, analog, regulator, AN1431T

B001

Ref. No. U001 U002 U003 U004 U005

Part No. 8236 5410 03 8234 1081 00 8236 0321 05 8236 0348 05 8236 5409 00

CAPACITORs ALU = Electrolytic type CER = Ceramic type PES=Mylar type Part No. Description N/A 8232 3491 03 VT, PES, 630V, 0.01µF, 10%, ECQ-EKF 8232 8011 00 VT, CER, 50V, 10pF, 5%, SL 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 3542 22 VT, CER, 250V, 0.0022µF, 20%, ECK-ZNS 8232 3533 91 VT, CER, 500V, 390pF, 10%, ECK-ZHT 8232 8181 04 VT, CER, 25V, 0.1µF, +80, YF 8232 8031 03 VT, CER, 50V, 0.01µF, +80, YF 8232 3241 07 VT, ALU, 400V, 100µF, 20%, SMH-VNSN, D25.4 8232 0964 76 V, ALU, 25V, 47µF, 20%, SME-VB 8232 3584 77 VT, ALU, 25V, 470µF, , 20%, LXV, D10 8232 3583 37 VT, ALU, 25V, 330µF, , 20%, LXV, D10 N/A

Ref. No. D001 D002 D003 D004 D005, 006

DIODEs Part No. Description 8234 1077 00 Stack, 600VAC, 1.5A, D2SBA60 8234 1079 00 HT, 80V, 0.2A, MA171 8234 1078 00 HT, 600V, 1.0A, D1N60 8234 1080 00 V, 200V, 5.0A, MA649 8234 1084 00 VT, SCHOTTKY, EK03W RESISTORs Part No. Description 8230 1251 04 H, metal, 2W, 100k, 5%, RSS 8230 1386 29 HT, carbon, 1/4W, 6.2, 5% 8230 1243 30 HT, metal, 1/2W, 33, 5%, RSS 8230 1387 50 HT, carbon, 1/4W, 75, 5%

Ref. No. R001 R002, 003 R004 R005

MISCELLANEOUS Part No. Description 8245 0530 08 Connector, PI, jack, 8263, 8P, WHT L001 N/A L002 8242 2501 03 Coil, PVT, 10µH, 2A, ELC L003 8242 2491 93 Filter, line, 19mH, 0.5A, ELF15N005 T001 8242 2480 00 Transformer, sw power, 27SF11, FD-4 W001~006 N/A W007 8277 4711 10 Cable assy, 250RECEPSIN1.8, BRN, L100 W008 N/A Y501 N/A Y502 8207 0015 00 Heat sink, 16PB16, L25, B Y503 Screw, P3 x 6, CZn Ref. No. J001

39

FD-4

· AC IN PCB assy
Ref. No. B101 Ref. No. C001 Part No. Description 8274 1390 00 PCB Assy, AC In, FD-4 8251 9691 02 Plain PCB, AC In, FD-4

Part No. Description 8232 3521 04 Capacitor, V, PES, 250VAC, 0.1µF, 20%, ECQ-UMV C021, 022 8232 3542 22 Capacitor, V, CER, 250V, 0.0022µF, 20%, ECK-ZNS E101 8239 0002 00 Holder, PI, fuse, S-N5057 L001 8242 2491 02 Filter, line, 1mH, 2.2A, ELF15N022 W001, 002 8245 5430 00 Terminal, IPS-5007 W003 8277 4711 10 Cable assy, 250RECEPSIN1.8, BRN, L100 W004 8277 4722 10 Cable assy, 1P, SIN1.8-SIN1.8, WHT, L100

Abbreviation T: F: P: V: H: I: Taping device Forming device Penetrate mount Vertical mount Horizontal mount I form

L: L form QFP: Quad Flat Package SOP: Small Outline Package SIP: Single In-line Package SOJ: Small Outline with J leads 220: TO-220 type

40

BLOCK DIAGRAM

MASTER PAN L L R STEREO OUT

INPUT1 -10dBV INPUT FADER

INPUT SEL INPUT OFF TRK1

EQ
R AUX1

8. CIRCUIT DIAGRAMS

AUX SEND 1 2 AUX2 MON L MON MON R TRK1 TRK1 REC MUTE1 MON SEL ST ST+MON MON MON L R TRK2 REC MUTE2 PHONES LO GAIN INPUT MID GAIN SHIFT HI GAIN

MON OUT