Text preview for : Gemini-X1_2_3_4 pwramp.pdf part of Gemini X1, 2, 3 & 4 power amplifier
Back to : Gemini-X1_2_3_4 pwramp.pd | Home
SERVICE MANUAL
X1 / X2 / X3 / X4
PROFESSIONAL AMPLIFIERS
Diagrams................................................ Features, Operating Instructions................... Specifications........................................... Troubleshooting........................................ Parts List................................................. Schematics..............................................
Page 2 Page 3 Page 5 Page 6 Page 7 Page 20
Page 1
X1 / X2 / X3
17
X4
Page 2
INTRODUCTION
Congratulations on purchasing a Gemini Power Amplifier. This state of the art power arnplifier includes the latest features and is backed by a three year limited warranty. Prior to use, we suggest that you carefully read all the instructions.
Rear panel Input Section:
1/4" Phone lnput Jacks (1, 2): accept a balanced as well as an unbalanced line level signal. The unbalanced line uses a standard tip-sleeve connection. The tip is positive and the sleeve is negative or ground. The balanced line uses a tip-ring-sleeve connection. Tip is hot or positive (+), ring is cold or negative (-), and sleeve is shield or ground. Operation Mode Switch (3): switch is used to set the unit for Stereo mode, Parallel Mono mode or Mono Bridge mode.
FEATURES
· State of the art bi-polar output stage technology for the finest sound quality and reliability · High output power to drive professional loudspeakers without clipping · Comprehensive protection circuity (Short Circuit, DC, Thermal Cut-off, Sub/Ultrasonic Frequency Filters, Turn-on Delay, Main Fuse, Secondary DC Fuses) · Three modes of operation - stereo, parallel mono and mono bridge · Active 1/4" Jack balanced/unbalanced inputs · Ground lift switch for flexibility in installations · Signal LEDs and Clip LEDs for better control on X1, X2, X3 amplifers · Large VU-meters and Clip LEDs for better control on X4 amplifier · Efficient dual aluminum extrusion heatsink design with directly mounted output transistors for no-fault operation · Efficient air guide with front-to-rear airflow for thermal stability and reliability · Compact 2U well balanced enclosure (3U for X4 model) · Steel reinforced chassis construction for durability and longevity
AC Power Section:
Fuse (8): replace fuse with those of proper type and rating. Ground Lift Switch (4) is used to lift the ground from the chassis, see the Ground Lift Switch Instructions for more detail. AC Inlet (16) is used to attach the power cord to the unit. AC line voltage switch (17) allows reconfiguring amplifier for either 110-120V or 220-240V AC lines.
Output Section:
Disconnect unit from the AC power source before making any connections. Pay close attention to polarity (shown on the back of the unit) when connecting your speakers. Connecting your speaker systems using the wrong polarity will not damage your speakers, but will impact the quality of the sound (lack of bass and incorrect stereo image). Speaker Outputs (5,6,7): the speaker output connectors are 3-way binding posts that will accept a standard banana plug, spade lugs, or bare wire. Make sure that all the connections are clean when using bare wire connections. If any strands of wire from one connector touch the adjacent connector, the sound will distort, and your amplifier will overheat and go into protection mode. NOTE: Total speaker impedance must not be lower than 4 Ohm per channel for Stereo and Parallel Mono modes, and 8 Ohm for Mono Bridge mode.
WORDS TO THE WISE
1. Read all operating instructions before using this equipment. 2. To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please contact the Gemini Service Department or your authorized dealer to speak to a qualified Gemini Sound Products technician. 3. Be sure to allow adequate front and rear ventilation to avoid possible heat damage to your equipment. 4. Be sure that AC power is OFF and all level controls are set to MINIMUM before making connections. This will eliminate any chance of unexpected, loud audio transients that could damage your speaker systems.
Front Panel
Power Switch (9) : turns the unit on and off. Power LED (10): the power LED lights when the power is on. If the power LED does not light, refer to the troubleshooting guide. Signal LED (13): the signal LEDs for each channel show when a signal is present. In Mono Bridge mode, both the channel 1 LED and the channel 2 LED will light in unison. Clip LED (14): the amplifier has true clip LEDs to help you properly control the amplifier's output and achieve undistorted sound. The clip LEDs for each channel light when your signal level is so strong that the distortion occurs. The clip LED should not remain constantly on or flash repeatedly during operation. For clean sound reproduction, the clip LED should only light occasionally for an instant. If the LED remains on or flashes repeatedly, you will hear distorted sound that can be damaging to your speaker systems. If this occurs, reduce the signal level by lowering the input level control for the channel that is clipping or reduce the level at the source. If the clip LED lights when no signal is present, it may indicate an RF signal on the output which may cause damage to speakers (the RF signal will not be audible). Please note that when you are using the amplifier in the Mono Bridge mode, both clip LEDs of the bridged channels will operate simultaneously. Protect LED (11): when you first turn on the amplifier, the protect LEDs light briefly during a turn-on delay which indicates that the outputs are disconnected internally. There will be an audible click when the outputs reconnect and the protect LED will turn off. Otherwise, the protect LED indicates that there is a problem either in the amplifier's external connections, load or temperature conditions or its internal
In the USA: If you experience problems with this unit, please call 1 (732) 738-9003 for Gemini Customer Service.
Do not attempt to return this equipment to your dealer.
5. Be sure that AC power is OFF when changing modes of operation and when changing the position of the ground lift switch. 6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Operators of electronic equipment should in no way be in contact with water. 7. When connecting to AC power line be sure you haven't lost the ground connection by using an adapter or extension cord without a 3 prong plug. 8. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
CONNECTION, CONTROLS AND INDICATORS
Page 3
functions. If one of these situations occurs, the amplifier senses the problem and automatically switches into protection mode. The LED will light to warn you of the trouble and the amplifier will stop working. If this occurs, switch off the amplifier and refer to the Troubleshooting Guide. If the protect LED remains lit when resuming amplifier operation, do not use the amplifier and contact an authorized service technician. Level Controls (12,15): establish the input levels required for each channel. Only the Channel 1 Level Control (15) works in Mono Bridge mode.
remains on or flashes repeatedly, reduce the signal level by lowering the input level control for the channel that is clipping or reduce the level at the source.
Mono Bridge Operation
Follow these instructions to bridge the unit's output. Bridging the amplifier converts the unit to a monophonic or single channel amplifier. The amplifier can be used with 8 Ohm or higher loads only in Mono Bridge mode. This mode is used to provide a higher voltage with greater headroom to your speaker. Before setting your amplifier for Mono Bridge operation, make sure that your speaker can handle the high power level provided by the amplifier in Mono Bridge mode. CAUTION: VOLTAGE OVER 100 VOLTS MAY BE PRODUCED AT THE BRIDGE OUTPUT TERMINALS IN THIS MODE. 1. With the power off, set the OPERATION MODE SWITCH (3) to the BRIDGE position. 2. With the power off, connect your input cables to channel 1 input only using the 1/4" INPUT JACK (1) of channel 1. 3. Connect the loudspeaker to the BRIDGE SPEAKER OUTPUT (6) only. Be sure the polarity of your connection is correct. The total speaker load must be at least 8 Ohms or above. If you try to operate at less than 8 Ohms in the Mono Bridge mode, the amplifier will go into the protection mode and stop operation until you correct the load conditions. 4. With the CHANNEL 1 LEVEL CONTROL (15) set to zero (fully counterclockwise), switch the power on. Apply a signal to the input. The level of the input signal should be as high as you will ever need it to be. This way, it will be as high above the amplifier's noise floor as possible, ensuring an excellent performance and signal to noise ratio. Adjust the LEVEL CONTROL (15) for channel 1 to achieve the desired maximum listening level. Note, when the clip LEDs light, there is distortion present in the amplifier's output section. If a clip LED remains on or flashes repeatedly, reduce the signal level by lowering the input level control for channel 1 or reduce the level at the source. During Mono Bridge operation, the channel 2 level is inactive, however, both channels LEDs will flash simultaneously and show output conditions.
OPERATION
THE AMPLIFIER'S POWER MUST BE TURNED OFF WHEN CHANGING MODES OF OPERATION.
Stereo Operation
The unit has two channels for stereo operation. Each channel provides a separate and discrete signal at the speaker outputs according to the signal received at the inputs. The following instructions are for applications with 4 Ohm or 8 Ohm speakers of matched power ratings. 1. With the power off, set the OPERATION MODE SWITCH (3) to the STEREO position. 2. With the power off, connect your input cables to the channel 1 and 2 inputs using the 1/4" INPUT JACKS (1, 2) of each channel. 3. Connect the loudspeakers to the channel 1 and channel 2 SPEAKER OUTPUTS (5,7). THE TOTAL SPEAKER LOAD MUST BE AT LEAST 4 OHMS PER CHANNEL. If you try to operate at a lower impedance, the amplifier will go into protection mode and stop operation until you correct the load conditions. 4. With the LEVEL CONTROLS (12,15) of both channels set to zero (fully counterclockwise), turn the POWER SWITCH (9) on. Apply a signal to the input of the amplifier. The level of the input signal should be as high as you will ever need it to be. This way, it will be as high above the amplifier's noise floor as possible, ensuring an excellent performance and signal to noise ratio. Adjust the LEVEL CONTROLS for each channel to achieve the desired maximum listening level. Note, when the clip LEDs light, there is distortion present in the amplifier's output section. If a clip LED remains on or flashes repeatedly, reduce the signal level by lowering the input level control for the channel that is clipping or reduce the level at the source.
Using the Ground Lift Switch
Depending on your system configuration, sometimes applying the ground will create a quieter signal path. Sometimes lifting the ground can eliminate ground loops and hum to create a quieter signal path. 1. With the power amp on, listen to the system in idle mode (no signal present) with the ground applied (the GROUND LIFT SWITCH (4) in the left position). 2. Turn the power off before moving the GROUND LIFT SWITCH (4). Lift the ground by moving the GROUND LIFT SWITCH to the right, turn the power back on and listen to determine which position will provide a signal free of background noise and hum. Keep the GROUND LIFT SWITCH in the ground position if the noise level remains the same in either position. CAUTION: DO NOT TERMINATE THE AC GROUND ON THE POWER AMPLIFIER IN ANY WAY. TERMINATION OF THE AC GROUND CAN BE HAZARDOUS.
Parallel Mono Operation
Follow these instructions for Parallel Mono Operation using a single input cable, and you will have the same monophonic signal on both the channel 1 and the channel 2 outputs. Each channel's output is controlled independently by that channel's level control. 1. With the power off, set the OPERATION MODE SWITCH (3) to the PARALLEL Mono position. 2. With the power off, connect your input cables to the channel 1 input only using the 1/ 4" INPUT JACK (1) of channel 1. 3. Connect the loudspeakers to the channel 1 and channel 2 SPEAKER OUTPUTS (5, 7). THE TOTAL SPEAKER LOAD MUST BE AT LEAST 4 OHMS PER CHANNEL. If you try to operate at less than 4 Ohms per channel, the amplifier will go into the protection mode and stop operation until you correct the load conditions. 4. With the LEVEL CONTROLS (12,15) set to zero (fully counterclockwise), switch the power on. Apply a signal to the input. The level of the input signal should be as high as you will ever need it to be. This way, it will be as high above the amplifier's noise floor as possible, ensuring an excellent performance and signal to noise ratio. Adjust the LEVEL CONTROLS for each channel to achieve the desired maximum listening level. Note, when the clip LEDs light, there is distortion present in the amplifier's output section. If a clip LED
Page 4
SPECIFICATIONS
X1 Output Power EIA: 1kHz @ 1% THD, Wrms Both Channels Driven 8 Both Channels Driven 4 Mono Bridge 8 Dynamic Headroom, dB: At8 At4 1.4 1.9 1.5 2.0 1.6 2.2 1.6 2.2 85 110 220 140 200 400 200 300 600 200 300 600 X2 X3 X4
Frequency Response ....................................................... 30 Hz - 50 kHz Total Harmonic Distortion ......... Iess than 0.05%, typical 0.02% at 1 kHz Signal to Noise ratio .......................... 100 dB below rated power @ 8 Damping factor .................................................... greater than 200 @ 8 Slew rate ..................................................................................... 20 V/µS Voltage gain, dB 28 30 32 32
Input Sensitivity (for rated power at 8 ) .................................... 1 Vrms Input Impedance Unbalanced .......................................................... 10 k Input Impedance Balanced .............................................................. 20 k Power consumption, W (at rated power at 4, both channels driven) AC Power Requirements ...... 110-120 V / 60 Hz and 220-240 V / 50 Hz Indicators ............................................................................. 1 Power LED 1 Protect LED 1 Signal LED per Channel (for X1, X2, X3) 1VU-meter per Channel (for X4) Cooling ...................................................... Fan, Front-to-Rear Forced Air Protection ........................................... Short Circuit, DC, Thermal Cut-off, Sub/Ultrasonic Frequency Filters, Turn-on Delay, Main Fuse, Secondary DC Fuses Connectors: Balanced/ Unbalanced lnputs .................................................... 1/4" Jack Speaker Outputs ..................................................... 5-way Binding Posts Dimensions: X1, X2, X3 ........................ 19"W x 10.75"D x 3.5"H (483 x 273 x 89 mm) X4 ................................. 19"W x 10.75"D x 5.25"H (483 x 273 x 133 mm) Weight 16.3 Ibs 17.8 Ibs 20.2 Ibs 21.6 Ibs 7.4 kg 8.1 kg 9.2 kg 9.8 kg 500 800 1200 1200
*Specifications and design are subject to change without notice for purpose of improvement
Page 5
TROUBLESHOOTING
SYMPTOM
UNIT DOES NOT PRODUCE SOUND. POWER LED DOES NOT LIGHT.
CAUSE
· POWER SWITCH NOT IN ON POSITION. · POWER CABLE NOT CONNECTED TO AMPLIFIER OR TO OUTLET. · AC OUTLET NOT ACTIVE. · MAIN AMPLIFIER FUSE DEFECTIVE
SOLUTION
· MOVE POWER SWITCH TO ON POSITION. · CONNECT POWER CABLE TO AC SUPPLY. · CHECK CONDITION OF OUTLET. · REPLACE AMPLIFIER MAIN POWER FUSE ON REAR PANEL WITH CORRECT TYPE AND RATING. · CHECK FOR PROPER FUNCTION OF INPUT SOURCE DEVICE. · CHECK INPUT CABLES AND CONNECTIONS. REPLACE QUESTIONABLE CABLES WITH KNOWN GOOD CABLES. · CHECK SPEAKER CABLES AND CONNECTIONS. REPLACE QUESTIONABLE CABLES WITH KNOWN GOOD CABLES. · CHECK OPERATING CONDITION AND STATUS OF SPEAKER SYSTEM (S). BE SURE THE LEVEL CONTROLS ARE PROPERLY SET.
POWER LED LIGHTS, BUT NO SOUND IS PRODUCED BY AMPLIFIER.
· NO INPUT SOURCE SIGNAL. · INPUT SOURCE NOT CONNECTED. · INPUT CONNECTING CABLE DEFECTIVE. · SPEAKER(S) NOT CONNECTED. · SPEAKER CABLE DEFECTIVE. · SPEAKER SYSTEM(S) INOPERATIVE. · AMPLIFIER'S LEVEL CONTROLS ARE SET TO ZERO
SOUND IS PRESENT BUT VOLUME IS TOO LOW EVEN THOUGH SOURCE DEVICE IS SET TO A HIGH LEVEL. LOUD 50/60 HZ OR 100/120 HZ HUM IS HEARD AT ALL TIMES THROUGH THE SPEAKER SYSTEMS.
· AMPLIFIER INPUT LEVEL CONTROLS ARE SET TOO LOW. · WRONG PIN CONNECTIONS IN CABLES. · IMPROPER OR DEFECTIVE GROUND CONNECTION AT INPUTS. IMPROPER OR DEFECTIVE GROUND AT INPUT SOURCE DEVICE(S). · IMPROPER OR DEFECTIVE GROUND CONNECTION ON AC OUTLET. · GROUND LOOP THROUGH AC LINE CONNECTION/RACK MOUNTING.
· ADJUST LEVEL CONTROLS AS PER INSTRUCTIONS. · USE CORRECT CABLES (AS SHOWN ON BACK OF UNIT). · CHECK FOR PROPER AC LINE GROUND ON POWER AMP AND ALL INPUT DEVICES. · CHECK INPUT CABLES FOR ALL SOURCE DEVICES AND SIGNAL PROCESSING AS WELL AS INPUT CABLES TO POWER AMPLIFIER. CHECK POSITION OF GROUND LIFT SWITCH AS PER INSTRUCTIONS FOR LIFTING THE GROUND. · NEVER LIFT THE AC LINE GROUND ON THE POWER AMPLIFIER. IF YOU ARE NOT TOTALLY FAMILIAR WITH GROUND LIFTING OR UNIFICATION PROCEDURES, DO NOT ATTEMPT THEM WITHOUT FIRST CONSULTING YOUR DEALER OR A QUALIFIED SOUND TECHNICIAN FOR MORE INFORMATION ON GROUNDING. IMPROPERLY DONE, SUCH PROCEDURES CAN POSE A SAFETY AND / OR FIRE HAZARD.
SOUND IS DISTORTED.
· DISTORTION OCCURRING IN SOURCE DEVICE. · INPUT LEVEL IS SET TOO HIGH.
· CHECK CLIP INDICATORS ON INPUT SOURCE DEVICES AND RESET LEVELS IF NECESSARY TO ELIMINATE DISTORTION. · ADJUST LEVEL CONTROLS AS PER INSTRUCTIONS.
PROTECT LED REMAINS LIT OR GOES ON AND OFF INTERMITTENTLY AFTER USING AMPLIFIER FOR A SHORT TIME.
· UNIT IS OPERATING AT EXCESSIVELY HIGH TEMPERATURE. · EXTREMELY LOW SPEAKER IMPEDANCE. · SHORT IN SPEAKER CONNECTORS, SPEAKER CABLE OR SPEAKER SYSTEM.
· CHECK THAT AMPLIFIER IS ADEQUATELY VENTILATED ON THE FRONT AND REAR PANELS WHERE THE AIR VENTS AND FANS ARE LOCATED. IF OVERHEATED, LET THE AMPLIFIER COOL DOWN BEFORE APPLYING AN INPUT SIGNAL. · CHECK THE POSITION OF OPERATION MODE SWITCH. BE SURE THAT THE SPEAKER CONNECTIONS ARE MADE IN ACCORDANCE WITH THE SWITCH SETTING. · VERIFY SPEAKER SYSTEM IMPEDANCES. BE SURE THE TOTAL SPEAKER SYSTEM IMPEDANCE IS AT LEAST 4 OHMS PER CHANNEL WHEN THE OPERATION MODE SWITCH IS IN THE STEREO POSITION OR PARALLEL MONO POSITION. IF THE SWITCH IS IN THE BRIDGE MODE, THE IMPEDANCE MUST BE AT LEAST 8 OHMS. IF YOU ARE NOT SURE OF YOUR TOTAL SPEAKER IMPEDANCE LOAD, CONTACT YOUR DEALER FOR MORE INFORMATION. · CHECK CONDITION OF SPEAKER CABLES. · IF USING BARE WIRE CONNECTIONS ON THE OUTPUTS OF THE AMPLIFIER, BE SURE THAT NO STRANDS FROM ONE CONNECTOR ARE TOUCHING ANY OTHER CONNECTOR.
FUSE BLOWS INTERMITTENTLY.
· SPEAKER LOAD IMPEDANCE IS TOO LOW. · TYPE OR RATING OF THE FUSE IS NOT CORRECT.
· CHECK FOR SHORTS ON THE OUTPUTS. · CHECK YOUR SPEAKER IMPEDANCE (INFO FROM DEALER). · CHECK THAT THE FUSE TYPE AND RATING IS CORRECT.
PROTECT LED STAYS ON WITH NO SPEAKERS CONNECTED AND WITH THE AMPLIFIER COOLED DOWN.
· FAILED AMPLIFIER.
· CONTACT THE GEMINI SERVICE DEPARTMENT OR YOUR AUTHORIZED DEALER TO SPEAK TO A QUALIFIED SERVICE TECHNICIAN. IN THE U.S.A. CALL TOLL FREE 1-800-476-8633
Page 6
PARTS LIST
PART# QUANTITY NAME
X-1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 012-029 021-463 031-048 022-861 041-446 041-449 151-131 003-111 003-612 003-748 047-496 049-206 153-217 196-127 255-200 157-996 156-089 1 1 1 2 2 1 1 2 2 6 3 4 1 3 1 1 1 PANEL CONTROL MAIN CHASSIS TOP COVER MOUNTING BRACKET HEAT SINK HEAT SINK (D) AIR GUIDE KNOB ROTARY (SMALL) SNAP RIVET LED HOUSING PCB SUPPORT PAD FOOT POLYFORM SERIAL NO:LABEL GIFT BOX OWNER'S MANUAL WARRANTY CARD
36 37 38 39 40
121-007A 110-138 111-046A 110-187A
10 6 2 2
41
111-044A
4
42 43 44 45 46 47 48 48-1 48-2 49 50 1 2 3 4 5 6
111-060 102-161 102-162 102-111 131-081 107-022A 131-074 142-008 143-008 170-363 262-328 262-329
1 9 1 2 1 4 4 2 2 1 1 1
099-232 099-233 099-234 099-238 095-057 099-167 099-169 099-014 099-214 190-062 160-044 160-052 160-009
2 2 2 2 3 1 1 1 1 1 1 1 1
LABEL-GREEN LABEL-RED LABEL-YELLOW UK LABEL VDE LABEL A LABEL V LABEL LABEL-MADE IN TAIWAN LABEL-MADE IN CHINA SILICON GEL PE BAG 160×250mm PE BAG 650×650mm PE BAG 23×30cm
BAND-HEAD TAPPING SCREW BTB-3 3×6(AB) BAND-HEAD TAPPING SCREW BTS-2 3×8(B) BAND-HEAD TAPPING SCREW BTS-3 3×6(AB) BAND-HEAD TAPPING SCREW/TWIN SCREW 3×12(AB) BAND-HEAD TAPPING SCREW ( "NUT" ) BTS-3 3×10(AB) PAN-HEAD TAPPING SCREW PTS-3 4×8(N) PAN-HEAD MACHINE SCREW 3×12(Y) PAN-HEAD MACHINE SCREW 4×18(Y) PAN-HEAD MACHINE SCREW PMS 5×8(B) NUT/WASHER3(B) BAND-HEAD MACHINE SCREW M4×15(AB) NUT (KNUT)4(B) PLAIN WASHER4(Y) SPRING WASHER4(Y) MASTER CARTON PRINTED CIRCUIT BOARD X4-1 PRINTED CIRCUIT BOARD X4-2 INTEGRATED CIRCUIT N JM4558DD INTEGRATED CIRCUIT OR BA15218 INTEGRATED CIRCUIT OR 5218A
074-163
2
Page 7
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
076-002 076-003 076-020 076-023
6
5
SILICON TRANSISTORS 2SC945 (Q)(P) SILICON TRANSISTORS OR 2SC1815 (Y)(GR) SILICON TRANSISTORS 2SA733 (Q)(P) SILICON TRANSISTORS OR 2SA1015 (GR)(Y)
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66
079-034 079-003 079-012 079-019 079-056 079-037
4 16 2 1 2 1
RECTIFIER DIODE 1N4004 OR SILICON DIODE 1N4148 ZENER DIODE 1/2W 12V (RD12EB,HZ12B2) ZENER DIODE 1/2W 5.6V (RD5.6EB2) ZENER DIODE 1/2 W 3.3V ZENER DIODE 1/2W 22V (RD22EB2,MTZ22B) LED (RED) 5 LED (YELLOW) 5 LED (GREEN) 5 ROTARY VR 10KA L:15MM SLIDE SWITCH 2P2C UL SLIDE SWITCH SLIDE SWITCH POWER SWITCH DC FAN 24V (80×80×25mm) 6.3PHONE JACK AC INLET (IEC SOCKET+FUSE) FUSE 20mm UL 6A AC250V FUSE 20mm VBS UTE 4A 250V FUSE 20mm VBS UTE 2A 250V 4P SPEAKER TERMINAL FUSE CLIP JH-6 POWER TRANSFORMER EI-86×65 COIL 1.3µH 1.0×9×9 1/2T AC CORD SVT AWG 18×3C VW-1 UL AC CORD 220V VDE AC CORD ARGENTINA AC CORD 230V BS
076-117
2
076-118
2
076-099 076-073 076-100 076-072 076-101 076-034
2
4
2
SILICON TRANSISTOR 2SA1943(O) OR (R) SILICON TRANSISTOR OR 2SA1429(O) OR (R) SILICON TRANSISTOR 2SC5200(O) OR (R) SILICON TRANSISTOR OR 2SD2155(O) OR (R) SILICON TRANSISTOR 2SA1837 SILICON TRANSISTOR OR 2SA1306 SILICON TRANSISTOR 2SC4793 SILICON TRANSISTOR OR 2SC3298(Y) SILICON TRANSISTOR 2SA1145(Y) OR (R) SILICON TRANSISTOR OR 2SA949(Y) OR (R) SILICON TRANSISTOR 2SC2705(Y) OR (O) SILICON TRANSISTOR OR 2SC2229(Y) OR (O) SILICON TRANSISTOR MPSA13 BRIDGE RECTIFIER KBPC804W RELAY SRET-202DP
080-085 080-110 080-086 071-220 081-023 081-030 081-041 083-099 001-613 092-078 092-105
4 1 3 2 1 1 1 1 1 2 1
100-058 100-063 100-064 161-172 161-109 059-232 147-024 093-370 093-371 093-410 093-369
2 1 1 1 4 1 2 1 1 1 1
076-102 076-037 076-134
4
1
086-019 086-512
1 1
Page 8
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93
073-506 063-005 062-023
2 1 4
METAL FILM RESISTORS 1/ 8W 10K 2% THERMISTOR PTH9M04BE222TS2F333 WIRE WOUND RESISTOR (CERAMIC) 3W 0.15 METAL FILM RESISTORS 2W 1.5K METAL FILM RESISTORS 1W 8.2 METAL FILM RESISTORS 1W 6.8K METAL FILM RESISTORS 1/ 4W 51.1K 1% METAL FILM RESISTORS 1/ 4W 1M 1% METAL FILM RESISTORS 1/ 4W 2.21K 1% CARBON FILM RESISTORS 1/4W 10 CARBON FILM RESISTORS 1/4W 62 CARBON FILM RESISTORS 1/4W 130 CARBON FILM RESISTORS 1/4W 300 CARBON FILM RESISTORS 1/4W 510 CARBON FILM RESISTORS 1/4W 2.2K CARBON FILM RESISTORS 1/4W 5.6K CARBON FILM RESISTORS 1/4W 16K CARBON FILM RESISTORS 1/4W 30K CARBON FILM RESISTORS 1/4W 68K ELECTROLYTIC CAPACITORS N.P 10µ/50V ELECTROLYTIC CAPACITORS N.P 100µ/10V ELECTROLYTIC CAPACITORS 100µ/16V
94 95 96 97 98 99
050-058 050-120 050-198
2 1 2
ELECTROLYTIC CAPACITORS 220µ/16V ELECTROLYTIC CAPACITORS 220µ/25V ELECTROLYTIC CAPACITORS 6800µ/50V CERAMIC CAPACITOR 0.01µ/500V CERAMIC CAPACITOR 22P/ 50V CERAMIC CAPACITOR 39 P/50V CERAMIC CAPACITOR 100P/50V CERAMIC CAPACITOR UL 0.0047µ/400V POLYESTER CERAMIC CAPACITOR 0.01µ/50V POLYESTER CERAMIC CAPACITOR 0.047µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/50V POLYESTER CERAMIC CAPACITOR 0.22µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/250V 12P(P=2.5mm), CONNECTOR BASE B2BXH-A
061-032 061-101 061-105 061-113 061-108 061-106
1 2 3 2 2 2
051-148 051-018
2 4 2 12 1
100 051-024 101 051-034 102 051-156 103 104 054-013 105 054-022 106 054-026 107 054-030 108 054-071 109 110 092-030
4 2 2 4 2
060-218 060-237 060-245 060-253 060-259
4 2 6 2 8
060-279 060-289 060-300 060-306 060-315
6 2 6 8 5
111 112 093-416
1
113 093-384 114 115 209-004
1
GROUND WIRE WITH RING TONGUE (GRN/YLW) 150mm GROUND WIRE WITH RING TONGUE (BLACK) 210mm LEAD WIRE (WHITE) UL1015#18AWG 6×6 310mm LEAD WIRE (RED) UL1015#18AWG 6×6 310mm
1
050-153 050-197 050-049
2 1 2
116 202-110
1
Page 9
117 118 060-703 119 060-703 120 060-703 121 060-703 122 060-703 123 060-703 124 060-703 125 126 146-509 127 128 190-075 129 190-230 130 190-063 131 132 003-605
PART#
QUANTITY
NAME
2 2 4 19 10 10 5
JUMPER WIRE 0.7 T/ 52mm P=5mm JUMPER WIRE 0.7 T/ 52mm P=6mm JUMPER WIRE 0.7 T/ 52mm P=7.5mm JUMPER WIRE 0.7 T/ 52mm P=10mm JUMPER WIRE 0.7 T/ 52mm P=12.5mm JUMPER WIRE 0.7 T/ 52mm P=15mm JUMPER WIRE 0.7 T/ 52mm P=20mm PIN CONNECTOR HEAT-SHRINK TUBING UL 28 35mm HEAT-SHRINK TUBING UL 35 35mm TUBE 1 30mm CABLE TIES CV-100
X-2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 012-030 021-464 031-048 022-861 041-447 041-449 151-131 003-111 003-612 003-748 047-496 049-206 153-217 196-128 255-201 157-997 156-089 1 1 1 2 2 1 1 2 2 6 3 4 1 3 1 1 1 PANEL CONTROL MAIN CHASSIS TOP COVER MOUNTING BRACKET HEAT SINK HEAT SINK (D) AIR GUIDE KNOB ROTARY (SMALL) SNAP RIVET LED HOUSING PCB SUPPORT PAD FOOT POLYFORM SERIAL NO:LABEL GIFT BOX OWNER'S MANUAL WARRANTY CARD
4 2 1 2 2
099-232 099-233 099-234 099-238 095-057 099-167 099-169 099-014 099-214 190-062 160-044 160-052 160-009 121-007A 110-138 111-046A 110-187A
2 2 2 2 3 1 1 1 1 1 1 1 1 10 6 2 2
LABEL-GREEN LABEL-RED LABEL-YELLOW UK LABEL VDE LABEL A LABEL V LABEL LABEL-MADE IN TAIWAN LABEL-MADE IN CHINA SILICON GEL PE BAG 160×250mm PE BAG 650×650mm PE BAG 23×30cm BAND-HEAD TAPPING SCREW BTB-3 3×6(AB) BAND-HEAD TAPPING SCREW BTS-2 3×8(B) BAND-HEAD TAPPING SCREW BTS-3 3×6(AB) BAND-HEAD TAPPING SCREW/TWIN SCREW 3×12(AB)
Page 10
41
111-044A
4
42 43 44 45 46 47 48 48-1 48-2 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
111-060 102-161 102-162 102-111 131-081 107-022A 131-074 142-008 143-008 170-364 262-328 262-329 ICs 074-163
1 13 1 2 1 4 4 2 2
BAND-HEAD TAPPING SCREW ( "NUT" ) BTS-3 3×10(AB) PAN-HEAD TAPPING SCREW PTS-3 4×8(N) PAN-HEAD MACHINE SCREW 3×12(Y) PAN-HEAD MACHINE SCREW 4×18(Y) PAN-HEAD MACHINE SCREW PMS 5×8(B) NUT/WASHER3(B) BAND-HEAD MACHINE SCREW M4×15(AB) NUT (KNUT)4(B) PLAIN WASHER4(Y) SPRING WASHER4(Y) MASTER CARTON PRINTED CIRCUIT BOARD X4-1 PRINTED CIRCUIT BOARD X4-2 INTEGRATED CIRCUIT NJM4558DD INTEGRATED CIRCUIT OR BA15218 INTEGRATED CIRCUIT OR 5218A SILICON TRANSISTORS 2SC945 (Q)(P) SILICON TRANSISTORS OR 2SC1815 (Y)(GR) SILICON TRANSISTORS 2SA733 (Q)(P) SILICON TRANSISTORS OR 2SA1015 (GR)(Y)
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
076-072 076-101 076-034 076-102 076-037 076-056 076-060 076-114 076-057 076-061 076-115 076-134 1 4 4 4 2
1 1
SILICON TRANSISTOR OR 2SC3298(Y) SILICON TRANSISTOR 2SA1145(Y) OR (R) SILICON TRANSISTOR OR 2SA949(Y) OR (R) SILICON TRANSISTOR 2SC2705(Y) OR (O) SILICON TRANSISTOR OR 2SC2229(Y) OR (O) SILICON TRANSISTORS 2SA1516 (O)(R) SILICON TRANSISTORS OR 2SA1386 (O)(R) SILICON TRANSISTORS OR 2SA1962 (O)(R) SILICON TRANSISTORS 2SC3907 (O)(R) SILICON TRANSISTORS OR 2SC3519 (O)(R) SILICON TRANSISTORS OR 2SC5242 (O)(R) SILICON TRANSISTOR MPSA13 BRIDGE RECTIFIER KBPC1004W RELAY SRET-202DP RECTIFIER DIODE 1N4004 SILICON DIODE 1N4148 ZENER DIODE 1/2W 12V (RD12EB,HZ12B2) ZENER DIODE 1/2W 5.6V (RD5.6EB2) ZENER DIODE 1/2 W 3.3V ZENER DIODE 1/2W 22V (RD22EB2,MTZ22B) LED (RED) 5 LED (YELLOW) 5 LED (GREEN) 5
2
086-029 086-512 DIODES 079-034 079-003 079-012 079-019 079-056 079-037 LEDS 080-085 080-110 080-086
1 1 4 16 2 1 2 1
TRANSISTORS 076-002 6 076-003 076-020 076-023 5
4 1 3
076-099 076-073 076-100
2
4
SILICON TRANSISTOR 2SA1837 SILICON TRANSISTOR OR 2SA1306 SILICON TRANSISTOR 2SC4793
SWITCHES 071-220 2 081-023 1 081-030 1 081-041 1 083-099 1
ROTARY VR 10KA L:15MM SLIDE SWITCH 2P2C UL SLIDE SWITCH SLIDE SWITCH POWER SWITCH
Page 11
50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
001-613 092-078 092-105
1 2 1
DC FAN 24V (80×80×25mm) 6.3PHONE JACK AC INLET (IEC SOCKET +FUSE) FUSE 20mm UL 8A AC250V FUSE 20mm VBS UTE 6.3A 250V FUSE 20mm VBS UTE 3.15A 250V 4P SPEAKER TERMINAL FUSE CLIP JH-6 POWER TRANSFORMER EI-86×80 COIL 1.3µH 1.0×9×9 1/2T AC CORD SVT AWG 18×3C VW-1 UL AC CORD 220V VDE AC CORD ARGENTINA AC CORD 230V BS METAL FILM RESISTORS 1/8W 10K 2% THERMISTOR PTH9M04BE222TS2F333 WIRE WOUND RESISTOR (CERAMIC) 3W 0.22
79 80 81 82
100-056 100-071 100-068
2 1 1
83 84 85 86 87
CARBON FILM RESISTORS 060-218 4 CARBON FILM RESISTORS 1/4W 10 060-237 2 CARBON FILM RESISTORS 1/4W 62 060-245 6 CARBON FILM RESISTORS 1/4W 130 060-253 2 CARBON FILM RESISTORS 1/4W 300 060-259 8 CARBON FILM RESISTORS 1/4W 510 060-279 CARBON FILM RESISTORS 1/4W 2.2K 060-289 3 CARBON FILM RESISTORS 1/4W 5.6K 060-300 6 CARBON FILM RESISTORS 1/4W 16K 060-306 8 CARBON FILM RESISTORS 1/4W 30K 060-315 5 CARBON FILM RESISTORS 1/4W 68K ELECTROLYTIC CAPACITORS 050-153 2 ELECTROLYTIC CAPACITORS N.P 10µ/50V 050-197 1 ELECTROLYTIC CAPACITORS N.P 100µ/10V 050-049 2 ELECTROLYTIC CAPACITORS 100µ/16V 050-058 2 ELECTROLYTIC CAPACITORS 220µ/16V 050-120 1 ELECTROLYTIC CAPACITORS 220µ/25V 050-154 2 ELECTROLYTIC CAPACITORS 6800µ/63V CERAMIC CAPACITORS 051-148 2 CERAMIC CAPACITOR 0.01µ/500V 051-018 4 CERAMIC CAPACITOR 22P/ 50V 051-024 2 CERAMIC CAPACITOR 39 P/50V 051-034 12 CERAMIC CAPACITOR 100P/50V 051-156 1 CERAMIC CAPACITOR UL 0.0047µ/400V 4
161-172 161-109 059-233 147-024 093-370 093-371 093-410 093-369 073-506 063-005 062-024
1 4 1 2 1 1 1 1 2 1 8
88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103
72 73 74 75 76 77 78
METAL FILM RESISTORS 061-102 2 METAL FILM RESISTORS 2W 8.2 061-030 1 METAL FILM RESISTORS 2W 2.2K 061-031 3 METAL FILM RESISTORS 1W 10K 061-111 2 METAL FILM RESISTORS 1/4W 69.8K 1% 061-108 2 METAL FILM RESISTORS 1/4W 1M 1% 061-106 2 METAL FILM RESISTORS 1/4W 2.21K 1%
Page 12
PART#
QUANTITY
NAME
104 105 054-013 106 054-022 107 054-026 108 054-030 109 054-071 110 111 092-030
4 2 2 4 2
POLYESTER CERAMIC CAPACITOR 0.01µ/50V POLYESTER CERAMIC CAPACITOR 0.047µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/50V POLYESTER CERAMIC CAPACITOR 0.22µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/250V 2P(P=2.5mm), CONNECTOR BASE B2B-XH-A GROUND WIRE WITH RING TONGUE (GRN/YLW) 150mm GROUND WIRE WITH RING TONGUE (BLACK) 210mm LEAD WIRE (WHITE) UL1015#18AWG 6×6 310mm LEAD WIRE (RED) UL1015#18AWG 6×6 310mm JUMPER WIRE 0.7 T/ 52mm P=5mm JUMPER WIRE 0.7T/ 52mm P=6mm JUMPER WIRE 0.7T/ 52mm P=7.5mm JUMPER WIRE 0.7 T/ 52mm P=10mm JUMPER WIRE 0.7 T/ 52mm P=12.5mm JUMPER WIRE 0.7T/ 52mm P=15mm JUMPER WIRE 0.7 T/ 52mm P=20mm PIN CONNECTOR CABLE TIES CV-100
X-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 012-031 021-465 031-048 022-861 041-448 041-449 151-131 003-111 003-612 003-748 047-496 049-206 153-217 196-129 255-202 157-998 156-089 1 1 1 2 2 1 1 2 2 6 3 4 1 3 1 1 1 PANEL CONTROL MAIN CHASSIS TOP COVER MOUNTING BRACKET HEAT SINK HEAT SINK (D) AIR GUIDE KNOB ROTARY (SMALL) SNAP RIVET LED HOUSING PCB SUPPORT PAD FOOT POLYFORM SERIAL NO:LABEL GIFT BOX OWNER'S MANUAL WARRANTY CARD
1
112 113 093-416
1
114 093-384 115 116 209-004
1
1
117 202-110
1
118 119 060-703 120 060-703 121 060-703 122 060-703 123 060-703 124 060-703 125 060-703 126 146-509 131 132 003-605
2 2 4 19 10 10 5 4 2
099-232 099-233 099-234 099-238 095-057 099-167 099-169 099-014 099-214 190-062 160-044 160-052 160-009 121-007A 110-138 111-046A 110-187A
2 2 2 2 3 1 1 1 1 1 1 1 1 10 6 2 2
LABEL-GREEN LABEL-RED LABEL-YELLOW UK LABEL VDE LABEL A LABEL V LABEL LABEL-MADE IN TAIWAN LABEL-MADE IN CHINA SILICON GEL PE BAG 160×250mm PE BAG 650×650mm PE BAG 23×30cm BAND-HEAD TAPPING SCREW BTB-3 3×6(AB) BAND-HEAD TAPPING SCREW BTS-2 3×8(B) BAND-HEAD TAPPING SCREW BTS-3 3×6(AB) BAND-HEAD TAPPING SCREW/TWIN SCREW 3×12(AB)
Page 13
43 44 45 46 47 48 48-1 48-2 49 50 1 2 3 4 5 6 7 8 9 10 11 50 12 13 14 15 16 17 18 19
102-161 102-162 102-111 131-081 107-022A 131-074 142-008 143-008 170-365 262-328 262-329
13 1 2 1 4 4 2 2 1 1 1
PAN-HEAD MACHINE SCREW 3×12(Y) PAN-HEAD MACHINE SCREW 4×18(Y) PAN-HEAD MACHINE SCREW PMS 5×8(B) NUT/WASHER3(B) BAND-HEAD MACHINE SCREW M4×15(AB) NUT (KNUT)4(B) PLAIN WASHER4(Y) SPRING WASHER4(Y) MASTER CARTON PRINTED CIRCUIT BOARD X4-1 PRINTED CIRCUIT BOARD X4-2 INTEGRATED CIRCUIT NJM4558DD INTEGRATED CIRCUIT OR BA15218 INTEGRATED CIRCUIT OR 5218A SILICON TRANSISTORS 2SC945 (Q)(P) SILICON TRANSISTORS OR 2SC1815 (Y)(GR) SILICON TRANSISTORS 2SA733 (Q)(P) SILICON TRANSISTORS OR 2SA1015 (GR)(Y) MASTER CARTON
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
076-073 076-100 076-072 076-101 076-034 2 4
SILICON TRANSISTOR OR 2SA1306 SILICON TRANSISTOR 2SC4793 SILICON TRANSISTOR OR 2SC3298(Y) SILICON TRANSISTOR 2SA1145(Y) OR (R) SILICON TRANSISTOR OR 2SA949(Y) OR (R) SILICON TRANSISTOR 2SC2705(Y) OR (O) SILICON TRANSISTOR OR 2SC2229(Y) OR (O) SILICON TRANSISTOR MPSA13 BRIDGE RECTIFIER KBPC1504W RELAY SRET-202DP RECTIFIER DIODE 1N4004 SILICON DIODE 1N4148 ZENER DIODE 1/2W 12V (RD12EB,HZ12B2) ZENER DIODE 1/2W 5.6V (RD5.6EB2) ZENER DIODE 1/2 W 3.3V ZENER DIODE 1/2W 22V (RD22EB2,MTZ22B)
076-102 076-037 076-134
4
1
086-030 086-512 079-034 079-003 079-012 079-019 079-056 079-037
1 1 4 16 2 1 2 1
074-163
2
076-002 076-003 076-020 076-023 170-365
6
37 38
5
1
076-117
4
076-118
4
076-099
2
SILICON TRANSISTOR 2SA1943(O) OR (R) SILICON TRANSISTOR OR 2SA1429(O) OR (R) SILICON TRANSISTOR 2SC5200(O) OR (R) SILICON TRANSISTOR OR 2SD2155(O) OR (R) SILICON TRANSISTOR 2SA1837
Page 14
39 40 41 42 43 44 45 46 47 48 49 50 51
76 080-085 080-110 080-086 071-220 081-023 081-030 081-041 083-099 001-613 092-078 4 1 3 2 1 1 1 1 1 2 LED (RED) 5 LED (YELLOW) 5 LED (GREEN) 5 ROTARY VR 10KA L:15MM SLIDE SWITCH 2P2C UL SLIDE SWITCH SLIDE SWITCH POWER SWITCH DC FAN 24V (80×80×25mm) 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
061-112 061-108 061-106
2 2 2
METAL FILM RESISTORS 1/ 4W 86.6K 1% METAL FILM RESISTORS 1/ 4W 1M 1% METAL FILM RESISTORS 1/ 4W 2.21K 1% CARBON FILM RESISTORS 1/4W 10 CARBON FILM RESISTORS 1/4W 62 CARBON FILM RESISTORS 1/4W 130 CARBON FILM RESISTORS 1/4W 300 CARBON FILM RESISTORS 1/4W 510 CARBON FILM RESISTORS 1/4W 2.2K CARBON FILM RESISTORS 1/4W 5.6K CARBON FILM RESISTORS 1/4W 16K CARBON FILM RESISTORS 1/4W 30K CARBON FILM RESISTORS 1/4W 68K ELECTROLYTIC CAPACITORS N.P 10µ/50V ELECTROLYTIC CAPACITORS N.P 100µ/10V ELECTROLYTIC CAPACITORS 100µ/16V ELECTROLYTIC CAPACITORS 220µ/25V ELECTROLYTIC CAPACITORS 220µ/16V ELECTROLYTIC CAPACITORS 6800µ/80V CERAMIC CAPACITOR 0.01µ/500V CERAMIC CAPACITOR 22P/ 50V CERAMIC CAPACITOR 39 / 50V
060-218 060-237 060-245 060-253 060-259
4 2 6 2 8
060-279 060-289 060-300 060-306 060-315
4 3 5 9 5
050-153 050-197 050-049 050-120 050-058 050-200
2 1 2 1 2 2
051-148
2 4 2
100 051-018 101 051-024
Page 15
102 051-034 103 051-156 104 105 054-013 106 054-022 107 054-026 108 054-030 109 054-071 110 111 092-030
12 1
CERAMIC CAPACITOR 100P/50V CERAMIC CAPACITOR UL 0.0047µ/400V POLYESTER CERAMIC CAPACITOR 0.01µ/50V POLYESTER CERAMIC CAPACITOR 0.047µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/50V POLYESTER CERAMIC CAPACITOR 0.22µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/250V 2P(P=2.5mm), CONNECTOR BASE B2B-XH-A GROUND WIRE WITH RING TONGUE (GRN/YLW) 150mm GROUND WIRE WITH RING TONGUE (BLACK) 210mm LEAD WIRE (WHITE) UL1015#18AWG 6×6 310mm LEAD WIRE (RED) UL1015#18AWG 6×6 310mm JUMPER WIRE 0.7 52mm P=5mm JUMPER WIRE 0.7 52mm P=6mm JUMPER WIRE 0.7 52mm P=7.5mm JUMPER WIRE 0.7 52mm P=10mm JUMPER WIRE 0.7 52mm P=12.5mm JUMPER WIRE 0.7 52mm P=15mm JUMPER WIRE 0.7 52mm P=20mm PIN CONNECTOR T/ T/ T/ T/ T/ T/ T/
127 128 190-075 129 190-230 130 190-063 131 132 003-605
PART#
2 1 2 2
4 2 2 4 2
HEAT-SHRINK TUBING UL 28 35mm HEAT-SHRINK TUBING UL 35 35mm TUBE 1 30mm CABLE TIES CV-100
NAME
QUANTITY
X-4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 012-034 021-466 031-048 022-863 022-031 041-448 041-449 151-131 003-111 003-612 003-748 047-496 049-206 153-217 196-133 255-206 257-003 156-089 099-232 099-233 099-234 099-238 095-057 099-167 099-169 099-014 099-214 190-062 160-044 160-052 160-009 1 1 1 2 2 2 1 1 2 2 4 3 4 1 3 1 1 1 2 2 2 2 3 1 1 1 1 1 1 1 1 PANEL CONTROL MAIN CHASSIS TOP COVER MOUNTING BRACKET VU METER BRACKET HEAT SINK HEAT SINK (D) AIR GUIDE KNOB ROTARY (SMALL) SNAP RIVET LED HOUSING PCB SUPPORT PAD FOOT POLYFORM SERIAL NO:LABEL GIFT BOX OWNER'S MANUAL WARRANTY CARD LABEL-GREEN LABEL-RED LABEL-YELLOW UK LABEL VDE LABEL A LABEL V LABEL LABEL-MADE IN TAIWAN LABEL-MADE IN CHINA SILICON GEL PE BAG 160×250mm PE BAG 650×650mm PE BAG 23×30cm
1
112 113 093-416
1
114 093-384 115 116 209-004
1
1
117 202-110
1
118 119 060-703 120 060-703 121 060-703 122 060-703 123 060-703 124 060-703 125 060-703 126 146-509
2 2 4 19 10 10 4 4
Page 16
36 37 38 39 40
12 121-007A 110-138 111-046A 110-187A 14 6 2 2 BAND-HEAD TAPPING SCREW BTB-3 3×6(AB) BAND-HEAD TAPPING SCREW BTS-2 3×8(B) BAND-HEAD TAPPING SCREW BTS-3 3×6(AB) BAND-HEAD TAPPING SCREW/TWIN SCREW 3×12(AB) BAND-HEAD TAPPING SCREW ( "NUT" ) BTS-3 3×10(AB) PAN-HEAD TAPPING SCREW PTS-3 4×8(N) PAN-HEAD MACHINE SCREW 3×12(Y) PAN-HEAD MACHINE SCREW 4×18(Y) PAN-HEAD MACHINE SCREW PMS 5×8(B) NUT/WASHER3 (B) BAND-HEAD MACHINE SCREW M4×15(AB) NUT (KNUT)4 (B) PLAIN WASHER4 (Y) SPRING WASHER4 (Y) MASTER CARTON PRINTED CIRCUIT BOARD X4-1 PRINTED CIRCUIT BOARD X4-2 INTEGRATED CIRCUIT NJM4558DD INTEGRATED CIRCUIT OR BA15218 INTEGRATED CIRCUIT OR 5218A SILICON TRANSISTORS 2SA1358 SILICON TRANSISTORS OR 2SB631 SILICON TRANSISTORS 2SC945 (Q)(P) SILICON TRANSISTORS OR 2SC1815 (Y)(GR) 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
076-020 076-023
5
SILICON TRANSISTORS 2SA733 (Q)(P) SILICON TRANSISTORS OR 2SA1015 (GR)(Y)
076-117
4
41
111-044A
4
076-118
4
42 43 44 45 46 47 48 48-1 48-2 49 50 1 2 3 4 5 6 7 8 9 10 11
111-060 102-161 102-162 102-111 131-081 107-022A 131-074 142-008 143-008 170-360 262-328 262-329
1 13 1 2 1 4 4 2 2
076-099 076-073 076-100 076-072
2
4
SILICON TRANSISTOR 2SA1943(O) OR (R) SILICON TRANSISTOR OR 2SA1429(O) OR (R) SILICON TRANSISTOR 2SC5200(O) OR (R) SILICON TRANSISTOR OR 2SD2155(O) OR (R) SILICON TRANSISTOR 2SA1837 SILICON TRANSISTOR OR 2SA1306 SILICON TRANSISTOR 2SC4793 SILICON TRANSISTOR OR 2SC3298(Y) SILICON TRANSISTOR 2SA1145(Y) OR (R) SILICON TRANSISTOR OR 2SA949(Y) OR (R) SILICON TRANSISTOR 2SC2705(Y) OR (O) SILICON TRANSISTOR OR 2SC2229(Y) OR (O) SILICON TRANSISTOR MPSA13 BRIDGE RECTIFIER KBPC1504W RELAY SRET-202DP VU METER RECTIFIER DIODE 1N4004 SILICON DIODE 1N4148 ZENER DIODE 1/2W 12V (RD12EB,HZ12B2) ZENER DIODE 1/2W 5.6V (RD5.6EB2) ZENER DIODE 1/2 W 3.3V ZENER DIODE 1/2W 22V (RD22EB2,MTZ22B)
076-101 076-034 076-102 076-037 076-134
2
4
1 1
1
074-163
2
086-030 086-512 087-027 079-034 079-003 079-012 079-019 079-056 079-037
1 1 2 4 16 2 1 2 2
076-075 076-077 076-002 076-003
1
6
Page 17
42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77
080-085 080-110 080-086 071-220 081-023 081-030 081-041 083-099 001-613 092-078 092-105 100-070 100-070 100-072
4 1 1 2 1 1 1 1 1 2 1 2 1 1
LED (RED) 5 LED (YELLOW) 5 LED (GREEN) 5 ROTARY VR 10KA L:15MM SLIDE SWITCH 2P2C UL SLIDE SWITCH SLIDE SWITCH POWER SWITCH DC FAN 24V (80×80×25mm) 6.3 PHONE JACK AC INLET (IEC SOCKET+FUSE) FUSE 20mm RU UTE 10A 250V FUSE 20mm RU UTE 10A 250V (110V) FUSE 20mm VBS UTE 5A 250V (230V) 4P SPEAKER TERMINAL FUSE CLIP JH-6 POWER TRANSFORMER 86×95 COIL 1.3µH 1.0×9×9 1/2T AC CORD SVT AWG 18×3C VW-1 UL AC CORD 220V VDE AC CORD ARGENTINA AC CORD 230V BS METAL FILM RESISTORS 1/8W 10K 2% THERMISTOR PTH9M04BE222TS2F333 WIRE WOUND RESISTOR (CERAMIC) 3W 0.22 METAL FILM RESISTORS 3W 470 METAL FILM RESISTORS 3W 100 METAL FILM RESISTORS 2W 8.2 METAL FILM RESISTORS 2W 2.7K METAL FILM RESISTORS 1W 10K
78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
061-112 061-108 061-106
2 2 2
METAL FILM RESISTORS 1/4W 86.6K 1% METAL FILM RESISTORS 1/4W 1M 1% METAL FILM RESISTORS 1/4W 2.21K 1% CARBON FILM RESISTORS 1/4W 10 CARBON FILM RESISTORS 1/4W 62 CARBON FILM RESISTORS 1/4W 130 CARBON FILM RESISTORS 1/4W 180 CARBON FILM RESISTORS 1/4W 300 CARBON FILM RESISTORS 1/4W 510 CARBON FILM RESISTORS 1/4W 750 CARBON FILM RESISTORS 1/4W 2.2K CARBON FILM RESISTORS 1/4W 4.7K CARBON FILM RESISTORS 1/4W 5.6K CARBON FILM RESISTORS 1/4W 16K CARBON FILM RESISTORS 1/4W 30K CARBON FILM RESISTORS 1/4W 68K ELECTROLYTIC CAPACITORS N.P 10µ/50V ELECTROLYTIC CAPACITORS N.P 100µ/10V ELECTROLYTIC CAPACITORS 22µ/25V ELECTROLYTIC CAPACITORS 100µ/16V ELECTROLYTIC CAPACITORS 220µ/25V ELECTROLYTIC CAPACITORS 220µ/16V
060-218 060-237 060-245 060-248 060-253 060-259 060-263
4 3 6 2 2 8 2
161-172 161-109 059-234 147-024 093-370 093-371 093-410 093-369 073-506 063-005 062-024
1 4 1 2 1 1 1 1 2 1 8
060-279 060-287 060-289 060-300
6 2 3 6
060-306 060-315
9 5
050-153
2 1 2 2 1 2
061-110 061-114 061-102 061-104 061-031
1 1 2 1 3
100 050-197 101 050-036 102 050-049 103 050-120 104 050-058
Page 18
111 112 054-013 113 054-022 114 054-026 115 054-030 116 054-071 117 118 092-030
4 2 2 4 2
POLYESTER CERAMIC CAPACITOR 0.01µ/50V POLYESTER CERAMIC CAPACITOR 0.047µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/50V POLYESTER CERAMIC CAPACITOR 0.22µ/50V POLYESTER CERAMIC CAPACITOR 0.1µ/250V 2P(P=2.5mm), CONNECTOR BASE B2B-XH-A 4P CONNECTOR BASE B4B-XH-A 180° 4P CONNECTOR WITH WIRE XH-4P STRIP×3 210mm GROUND WIRE WITH RING TONGUE (GRN/YLW) 150mm GROUND WIRE WITH RING TONGUE (BLACK) 210mm LEAD WIRE (WHITE) UL1015#18AWG 6×6 310mm LEAD WIRE (RED) UL1015#18AWG 6×6 310mm JUMPER WIRE 0.7 T/ 52mm P=5mm JUMPER WIRE 0.7 T/ 52mm P=6mm JUMPER WIRE 0.7 T/ 52mm P=7.5mm JUMPER WIRE 0.7 T/ 52mm P=10mm JUMPER WIRE 0.7 T/ 52mm P=12.5mm JUMPER WIRE 0.7 T/ 52mm P=15mm JUMPER WIRE 0.7 T/ 52mm P=20mm
133 134 146-509 135 136 190-075 137 190-230 138 190-063 139 140 003-605
4 2 1 2 5
PIN CONNECTOR HEAT-SHRINK TUBING UL 28 35mm HEAT-SHRINK TUBING UL 35 35mm TUBE 1 30mm CABLE TIES CV-100
1
119 092-031 120 091-490
2 2
121 122 093-416
1
123 093-384 124 209-004
1 1
125 202-110
1
126 060-703 127 060-703 128 060-703 129 060-703 130 060-703 131 060-703 132 060-703
2 2 4 20 10 13 5
Page 19
8
3 RA1B 5 4 R30 51.1K1% 22pF D12 1N4148 C10 - 15V 3 100pF 6 7 5 R68 D18 1N4148 R51 0.15R3W5% RLY1A 3 L2 R28 510 D3 1N4148 R37 510 C37 0.1uF100V 4 Q18 2SA1943 C28 0.01 R61 30K D5 1N4148 D9 1N4004 R47 10 R42 0.15R3W5% 1 1.0uH 53 R1 C16 2.2K R27 30K R63 510 8R2 1W Left ch. OUTPUT J3A IC1B R8 68K R15 2.21K1% C11 100pF LD1 RED R13 300 Q2 2SC2705 Q23 2SC5200 Q27 2SC1815 R55 10 C34 0.01 R26 16K 130 RA1C 10K2% 6 C6 100pF 4 R29 1M1% D11 1N4004 C21 22pF 3 R64
1
2
5
X-1
C1 100pF +E 8 RA1D 7 ZD5 3.3V 0.5W R24 2.2K Q6 2SA1145 C32 100pF IC1A 4558DD C3 1 C23 Q26 2SC4793 10uF25V NP 10K2% Q5 2SA1015 R25 62
MAIN PCB
+ 15V
Left ch. INPUT 2 RA1A 1 2 T R S 10K2% 10K2% J1 TRS 1/4" BAL
D2
D6
1N4148
1N4148
Left ch. GAIN C20 0.22uF R14 16K 2 VR1 10KA
C17 0.22uF
R34 6,8K1W
LD3 GRN "SIGNAL"
LD4 RED "OL"
39pF
R9 SW2 "Signal ground lift" R38 130 Q19 2SA1837 Q10 2SC2705 C30 100pF C7 510
Q13 2SA1015
R65 6.8K1W
0.047uF 1 7 6 4 8 C12 R32 30K
5
SW1B
3 6
D14
D13
0.047uF R10 510 Q11 2SC1815 R39 130
1N4148
1N4148 LD6 GRN "SIGNAL" -E R69 68K LD5 RED "OL"
8
3
4
1
8
POWER PCB 16K 1N4148 -E - 12V Y1 RED 7 BLK 2 Y3 RED X4 RED C45 0.01 C40 6800uF50V 1 ZD1 12V 0.5W 4 X6 BLK F1 6,3A R23 1.5K 2W Y2 C39 0.01 C5 220uF16V X3 RED 3 KBPS804 REC1
P3
R67 30K R35 R33 30K 130 Q15 2SA1837 Q8 2SC2705 C29 100pF C15 0.1 R36 130 Q9 2SC1815 C43 100uF10V NP Q30 2SC1815 Q31 2SC1815 C46 100uF16V D4 1N4148 D8 1N4004 RT1 PTC90F2
7
Page 20
SW1A "Stereo / Parallel mono / Bridge" C36 10uF25V NP 1 3 Q7 2SA1015 C31 100pF Q4 2SA1145 R21 62 4 ZD3 3.3V 0.5W R22 2.2K RA2C 10K2% C24 100pF C26 15 RA2D 16 C22 R12 16K Q28 2SC1815 22pF D16 1N4148 C33 0.01 + 15V C19 0.22uF 100pF 6 R6 16K 5 IC2B R4 68K R7 C14 2.2K R20 30K R11 2.21K1% C18 100pF D15 1N4148 LD2 RED R60 510 R53 0.15R3W5% 7 R16 300 Q1 2SC2705 C13 0.22uF 2 VR2 10KA 10K2% R18 51.1K1% R17 1M1% 130 C25 22pF 14 R54 13 SW1D Q25 2SC4793 2 R56 10 Q22 2SC5200 Right ch. INPUT 2 1 3 Right ch. GAIN J2 TRS 1/4" BAL RA2A 10K2% T R S RA2B 10K2% IC2A 4558DD C8 - 15V 100pF R19 510 D7 1N4148 9 6 12 R73 A D20 11 10 Q12 2SA1015 Q17 2SA1943 C27 0.01 R48 10 SW1C 39pF R45 510 R41 0.15R3W5% Y7 GRN X7 GRN 8 B C41 6800uF50V +E F2 6,3A
R66
68K
B +E R78 0/jumper R72 5.6K R70 6.8K1W Q29 2SA1015 D10 1N4004 R76 30K R75 68K R77 30K LD7 YEL "PROTECT" C44 220uF25V 2 R59 8R2 1W RLY1B 4 L1 1.0uH 62 2 A D19 C38 0.1uF100V 1 R74 16K 1N4148 12V RLY1C Q3 2SC3421 C42 100uF16V ZD2 12V 0.5W D21 1N4148 C4 220uF16V + 12V Right ch. OUTPUT J3B D22 1N4148 ZD7 5.6V 0.5W 2 LD8 GRN "POWER" R79 2.2K Q32 2SC3421
ZD6 22V 0.5W FAN 1 X5 Y4 1 FAN1 24V 0.13A
P1
SW3 SW-POWER
T1
P2
BRN
5
C101
C9 0.1
4A 115V / 3.15A 230V
BLU
F
L
4
3
E
R80 5.6K
Q33 MPSA13
ORG
N
SW4 VOLTAGE SELECTOR
115v
230v
-E
AC INLET
BLK
2
WHT
1
8
5
4
6
3
1
2
5
X-2
C1 100pF +E 8 RA1D 7 ZD5 3.3V 0.5W R24 2.2K Q6 2SA1145 C32 100pF 10K2% Q5 2SA1015 R25 62
MAIN PCB
+ 15V
Left ch. INPUT 2 RA1A 1 1 C23 R64 130 D12 1N4148 D2 C34 0.01 R55 10 Q23 2SC5242 R68 D18 1N4148 R51 0.22R3W5% RLY1A 3 L2 R28 510 D3 1N4148 R37 510 C37 0.1uF100V 4 R9 SW2 "Signal ground lift" C7 R38 130 Q19 2SA1837 Q10 2SC2705 C30 100pF R69 68K -E D14 D13 D9 1N4004 D5 1N4148 R61 30K 510 C28 0.01 R47 10 Q13 2SA1015 Q18 2SA1962 Q20 2SA1962 R65 10K1W R42 0.22R3W5% R43 0.22R3W5% 1 1.0uH 53 Left ch. OUTPUT J3A R52 0.22R3W5% R1 C16 2.2K R27 30K R63 510 8R2 2W R34 10K1W Q24 2SC5242 Q27 2SC1815 LD1 RED IC1B R8 68K R15 2.21K1% C11 100pF D11 1N4004 D6 Q26 2SC4793 R30 69.8K1% 22pF C10 - 15V 100pF 6 7 5 R13 300 R26 16K 1N4148 RA1C 10K2% C6 100pF R29 1M1% C21 22pF 4 3 2 C3 10uF25V NP T R S 3 RA1B 10K2% 10K2% J1 TRS 1/4" BAL
IC1A 4558DD
1N4148
Left ch. GAIN C20 0.22uF R14 16K 2 VR1 10KA
C17 0.22uF
Q2 2SC2705
LD3 GRN "SIGNAL"
LD4 RED "OL"
39pF
0.047uF 1 7 6 4 8 C12
5
SW1B
3 6
R32 30K
0.047uF R10 510 Q11 2SC1815 R39 130
1N4148
1N4148 LD6 GRN "SIGNAL" LD5 RED "OL"
SW1A "Stereo / Parallel mono / Bridge" C36 10uF25V NP 1 3 4 ZD3 3.3V 0.5W R22 2.2K Q4 2SA1145 RA2C 10K2% C24 100pF C26 15 RA2D 16 C22 R12 16K C33 0.01 Q28 2SC1815 22pF D16 1N4148 + 15V C19 0.22uF 3 100pF 6 R6 5 IC2B 1 R4 68K R7 C14 R19 510 2.2K R20 30K R11 2.21K1% C18 100pF D15 1N4148 LD2 RED R60 510 16K 7 R16 300 Q1 2SC2705 C13 0.22uF 2 VR2 10KA 4 10K2% R18 69.8K1% 130 R17 1M1% C25 22pF 14 R54 13 SW1D Q25 2SC4793 C31 100pF 2 Q7 2SA1015 R21 62
R66
68K
B +E R78 0/jumper R72 5.6K R70 10K1W Q29 2SA1015 D10 1N4004 R76 30K R75 68K R77 30K LD7 YEL "PROTECT" LD8 GRN "POWER" R79 2.2K Q32 2SC3421
8
8
POWER PCB 16K 1N4148 -E - 12V
P3
R67 30K R35 R33 30K 130 Q15 2SA1837 Q8 2SC2705 C29 100pF Q9 2SC1815 R36 130 C43 100uF10V NP Q30 2SC1815 Q31 2SC1815 C46 100uF16V D4 1N4148 D8 1N4004 RT1 PTC90F2
7
F 7 BLK 2 Y3 RED C40 6800uF63V 1 C15 0.1 ZD1 12V 0.5W X4 RED C45 0.01 4 F1 8A R23 2.2K 2W Y2 X6 BLK C39 0.01 C5 220uF16V
Y1 RED X3 RED 3 REC1 KBPS1004
Page 21
R56 10 Q22 2SC5242 Right ch. INPUT 2 1 3 Right ch. GAIN J2 TRS 1/4" BAL RA2A 10K2% T R S RA2B 10K2% IC2A 4558DD R53 0.22R3W5% C8 - 15V 100pF D7 1N4148 9 6 11 12 R73 A D20 10 Q12 2SA1015 Q17 2SA1962 C27 0.01 R48 10 SW1C 39pF R45 510 R41 0.22R3W5% Y7 GRN X7 GRN 8 B +E F2 8A C41 6800uF63V
ZD6 22V 0.5W FAN 1 C44 220uF25V Q21 2SC5242 R59 R50 0.22R3W5% 8R2 2W RLY1B 4 L1 R44 0.22R3W5% C38 0.1uF100V 1 Q16 2SA1962 R74 16K 1N4148 12V RLY1C Q3 2SC3421 C42 100uF16V ZD2 12V 0.5W 1.0uH 62 2 A D19 D21 1N4148 C4 220uF16V + 12V Right ch. OUTPUT J3B D22 1N4148 2 ZD7 5.6V 0.5W 2 X5 Y4 1 FAN1 24V 0.13A
P1
SW3 SW-POWER
T1
P2
BRN
5
C101
C9 0.1
6.3A 115V / 4A 230V
BLU
L
4
3
E
R80 5.6K
Q33 MPSA13
ORG
N
SW4 VOLTAGE SELECTOR
115v
230v
-E
AC INLET
BLK
2
WHT
1
8
3 RA1B
5
4
6
3
1
2
5
X-3
C1 100pF +E 8 RA1D 7 ZD5 3.3V 0.5W R24 2.2K Q6 2SA1145 C32 100pF 10K2% Q5 2SA1015 R25 62
MAIN PCB
+ 15V
Left ch. INPUT 2 RA1A 1 1 4 R30 86.6K1% 22pF D12 1N4148 C34 0.01 R55 10 Q23 2SC5200 R68 D18 1N4148 R51 0.22R3W5% RLY1A 3 L2 R28 510 D3 1N4148 R37 510 C37 0.1uF100V 4 R9 SW2 "Signal ground lift" C7 R38 130 Q19 2SA1837 Q10 2SC2705 C30 100pF R69 68K -E D14 D9 1N4004 D5 1N4148 R61 30K 510 C28 0.01 R47 10 Q13 2SA1015 Q18 2SA1943 Q20 2SA1943 R65 R42 0.22R3W5% R43 0.22R3W5% 1 1.0uH 53 Left ch. OUTPUT J3A R52 0.22R3W5% R1 C16 2.2K R27 30K R63 510 8R2 2W Q24 2SC5200 Q27 2SC1815 LD1 RED IC1B R8 68K R15 2.21K1% C11 100pF C10 - 15V 100pF 6 7 5 R13 300 R26 16K 130 RA1C 10K2% C6 100pF R29 1M1% C21 22pF D11 1N4004 D2 3 R64 C23 Q26 2SC4793 2 C3 10uF25V NP T R S 10K2% 10K2% J1 TRS 1/4" BAL
IC1A 4558DD
D6
1N4148
1N4148
Left ch. GAIN 2 VR1 10KA R14 16K
C20 0.22uF
C17 0.22uF
Q2 2SC2705
R34 10K1W
LD3 GRN "SIGNAL"
LD4 RED "OL"
39pF
10K1W
0.047uF 1 7 6 4 8 C12
5
SW1B
3 6
R32 30K
D13
0.047uF R10 510 Q11 2SC1815 R39 130
1N4148
1N4148 LD6 GRN "SIGNAL" LD5 RED "OL"
SW1A "Stereo / Parallel mono / Bridge" C36 10uF25V NP 1 3 4 ZD3 3.3V 0.5W R22 2.2K Q4 2SA1145 RA2C 10K2% C24 100pF C26 15 RA2D 16 D16 1N4148 C33 0.01 C22 R12 16K Q28 2SC1815 22pF + 15V C19 0.22uF
3
R66
68K
B +E Q32 2SC3421 R78 100R 2W
8
4
1
8
POWER PCB 30K 1N4148 -E - 12V Y1 REC1
3
P3 X3 RED KBPS1204 C5 220uF16V X6 BLK F1 2 Y3 RED C40 6800uF80V
1
R67 30K R35 R33 30K 130 Q15 2SA1837 Q8 2SC2705 C29 100pF C15 0.1 R36 130 Q9 2SC1815 C43 100uF10V NP Q30 2SC1815 Q31 2SC1815 C46 100uF16V D4 1N4148 D8 1N4004 RT1 PTC90F2
7
Page 22
2 Q7 2SA1015 C31 100pF R21 62 13 14 R18 86.6K1% 130 R17 1M1% C25 22pF R54 SW1D Q25 2SC4793 10K2% 100pF 6 R6 5 IC2B R4 68K R11 2.21K1% R7 C14 R19 510 2.2K R20 30K C18 100pF D15 1N4148 LD2 RED R60 510 R53 0.22R3W5% 16K 7 R16 300 C13 0.22uF 2 VR2 10KA R56 10 Q22 2SC5200 Right ch. INPUT 2 1 3 Right ch. GAIN J2 TRS 1/4" BAL RA2A 10K2% T R S RA2B 10K2% IC2A 4558DD Q1 2SC2705 C8 - 15V 100pF D7 1N4148 9 6 11 12 R73 A D20 10 Q17 2SA1943 Q12 2SA1015 C27 0.01 R48 10 SW1C 39pF R45 510 R41 0.22R3W5% RED 7 10A 4 R23 2.7K 2W C39 0.01 Y2 BLK X4 RED C45 0.01 ZD1 12V 0.5W Y7 GRN X7 GRN 8 B C41 6800uF80V +E F2 10A
R72
5.6K R70 10K1W Q29 2SA1015 D10 1N4004 R76 30K R75 68K R77 30K LD7 YEL "PROTECT" LD8 GRN "POWER"
R79 5.6K
ZD6 22V 0.5W FAN 1 C44 220uF25V Q21 2SC5200 R59 R50 0.22R3W5% 8R2 2W RLY1B 4 L1 R44 0.22R3W5% C38 0.1uF100V 1 Q16 2SA1943 R74 16K 1N4148 ZD2 12V 0.5W 12V RLY1C Q3 2SC3421 C42 100uF16V 1.0uH 62 2 A D19 D21 1N4148 C4 220uF16V + 12V Right ch. OUTPUT J3B D22 1N4148 2 ZD7 5.6V 0.5W 2 X5 Y4 1 FAN1 24V 0.13A
P1
SW3 SW-POWER
T1
P2
BRN
5
C101
C9 0.1
10A 115V / 6.3A 230V
BLU
F
L
4
3
E
R80 5.6K
Q33 MPSA13
ORG
N
SW4 VOLTAGE SELECTOR
115v
230v
-E
AC INLET
BLK
2
WHT
1
C1 +E 10K2% 7 D1 R31 2.2K C2 22uF25V 4.7K R5 180 R2 ZD5 3.3V 0.5W R24 2.2K Q6 2SA1145 C32 100pF 1N4148 IC1A 4558DD C3 1 C23 R64 130 D12 1N4148 D2 C34 0.01 R55 10 Q23 2SC5200 R68 D18 1N4148 R51 0.22R3W5% RLY1A 3 L2 R28 510 D3 1N4148 R37 510 C37 0.1uF100V 4 Q13 2SA1015 C28 0.01 R61 30K D5 1N4148 D9 1N4004 R47 10 Q18 2SA1943 Q20 2SA1943 R65 10K1W D17 R71 1N4148 D14 2.2K R62 4.7K R58 180 ZD4 22V 0.5W R42 0.22R3W5% R43 0.22R3W5% 1 1.0uH 53 Left ch. OUTPUT J3A R52 0.22R3W5% R1 C16 2.2K R27 30K R63 510 8R2 2W R34 10K1W Q24 2SC5200 Q27 2SC1815 LD1 RED IC1B R8 68K R15 2.21K1% C11 100pF D11 1N4004 R30 86.6K1% 22pF C10 R26 16K 1N4148 R29 1M1% C21 22pF Q26 2SC4793 10uF25V NP Q5 2SA1015 R25 62
100pF
MAIN PCB
8 RA1D
X1 R3 750 2 1
+ 15V
Left ch. INPUT
3 RA1B
10K2%
5
RA1C 10K2% 3 100pF 6 7 5 R13 300
C6 100pF
6
4
1
2
5
X-4
Left ch. GAIN C20 0.22uF R14 16K 2 VR1 10KA C17 0.22uF Q2 2SC2705 LD4 RED "OL" R49 470R 3W Q14 2SA1358 R40 62 39pF R46 16K R57 750 C35 22uF25V 5 R32 30K 6 Q19 2SA1837 Q10 2SC2705 C30 100pF R69 68K -E 130 7 8 SW1B R38 1N4148 LD5 RED "OL" Q11 2SC1815 R39 130 C36 10uF25V NP +E Q7 2SA1015 R21 62 C31 100pF Q4 2SA1145 R72 5.6K R70 10K1W R78 100R 3W R79 5.6K R66 68K B Q32 2SC4793 ZD3 3.3V 0.5W R22 2.2K RA2C 10K2% C24 100pF C26 15 RA2D 16 C22 C33 0.01 R12 16K Q28 2SC1815 22pF D16 1N4148 + 15V C19 0.22uF 3 100pF 6 R6 5 IC2B 1 R4 68K R7 C14 R19 510 2.2K R20 30K L1 D7 1N4148 R45 510 R41 0.22R3W5% R44 0.22R3W5% C38 0.1uF100V 1 Q12 2SA1015 Q17 2SA1943 C27 0.01 R67 30K R35 R33 30K 130 Q15 2SA1837 6 Q8 2SC2705 C29 100pF Q9 2SC1815 R73 30K 7 Y1 RED Y2 BLK Y3 RED X4 RED X6 BLK C39 0.01 F1 2 C45 0.01 1 4 10A X3 RED REC1 3 KBPS1204 R23 2.7K 2W C5 220uF16V D20 A 1N4148 -E - 12V R36 130 C43 100uF10V NP Q30 2SC1815 Q31 2SC1815 C46 100uF16V D4 1N4148 D8 1N4004 Q33 MPSA13 R80 5.6K RT1 PTC90F2 R48 10 Q16 2SA1943 R74 16K 1N4148 8 12V RLY1C ZD2 12V 0.5W 1.0uH R11 2.21K1% C18 100pF D15 1N4148 LD2 RED R60 510 16K 7 R16 300 Q1 2SC2705 C13 0.22uF 2 VR2 10KA 4 10K2% R18 86.6K1% R17 1M1% 130 C25 22pF 14 R54 Q25 2SC4793 D10 1N4004 R76 30K R75 68K R77 30K LD7 YEL "PROTECT" R56 10 Q22 2SC5200 Q21 2SC5200 R59 R53 0.22R3W5% R50 0.22R3W5% 8R2 2W RLY1B 4 62 2 A D19 D21 1N4148 Right ch. OUTPUT J3B D22 1N4148 C44 220uF25V 13 SW1D Q29 2SA1015 LD8 GRN "POWER" ZD6 22V 0.5W 8 IC2A 4558DD Right ch. GAIN 1 3 2 ZD7 5.6V 0.5W C8 - 15V 100pF 39pF 7 C42 100uF16V T1 -E C40 6800uF80V ZD1 12V 0.5W C15 0.1 Gemini Sound Products Corp. 8 Germak Dr., Carteret, NJ 07001, USA Phone 732-969-9000 Fax 732-969-9090 POWER AMPLIFIER P-8 8 Y7 GRN X7 GRN B C41 6800uF80V +E F2 10A
2 RA1A
10K2%
1
2
8
3
J1 TRS 1/4" BAL
4
3
T R S
4
- 15V
X2 1
R9
SW2
510
2
"Signal ground lift"
C7
3
0.047uF
3
1
4
6
4
C12
0.047uF
R10
510
SW1A "Stereo / Parallel mono / Bridge"
1
3
2
Page 23
4
FAN 1
X5
Right ch. INPUT
2
J2 TRS 1/4" BAL
T R S
RA2A
10K2%
RA2B 10K2%
+ 12V
9
SW1C
11
10
C4 220uF16V
12
C9 Q3 2SC4793 0.1
P1
SW3 SW-POWER
P2
BRN
5
C101 0.0047/400V
POWER PCB
P3
10A 115V / 6.3A 230V
BLU
F
L
4
3
E
ORG
N
SW4 VOLTAGE SELECTOR
115v
230v
AC INLET
BLK
2
WHT
1
X-4
Size A2 Scale
FCSM No.
DWG No. SCHEMATIC: MAIN PCB Sheet 1 of 1
Rev 0
In the USA: If you experience problems with this unit, call 1 (732) 738-9003 for Gemini Customer Service.
Do not attempt to return this equipment to your dealer.
Parts of the design of this product may be protected by worldwide patents. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. Gemini Sound Products Corp. shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual. No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written permission of Gemini Sound Products Corp. It is recommended that all maintenance and service on this product is performed by Gemini Sound Products Corp. or its authorized agents. Gemini Sound Products Corp. will not accept liability for loss or damage caused by maintenance or repair performed by unauthorized personnel.
Worldwide Headquarters · 120 Clover Place, Edison, NJ 08818 · USA Tel: (732) 738-9003 · Fax: (732) 738-9006
France · G.S.L. France · 11, Avenue Leon Harmel, Z.I. Antony, 92160 Antony, France Tel: + 33 (0) 1 55 59 04 70 · Fax: + 33 (0) 1 55 59 04 80 Germany · Gemini Sound Products GmbH · Ottostrasse 6, 85757 Karlsfeld, Germany Tel: 08131 - 39171-0 · Fax: 08131 - 39171-9 UK · Gemini Sound Products · Unit C4 Hazleton Industrial Estate, Waterlooville, UK P08 9JU Tel: 087 087 00880 · Fax: 087 087 00990 Spain · Gemini Sound Products S.A. · Mino, 112, Nave 1, 08223 Terrassa, Barcelona, Spain Tel: 011-34-93-736-34-00 · Fax: 011-34-93-736-34-01
© Gemini Sound Products Corp. 2001
All Rights Reserved
Page 24