Text preview for : HarmanKardon-HKTS5-6 actspk system.pdf part of Harman/Kardon HKTS5-6 active speakers system
Back to : HarmanKardon-HKTS5-6 acts | Home
harman/kardon
HKTS 5/HKTS 6
Home Theater Speaker System
SERVICE MANUAL
harman/kardon, Inc.
250 Crossways Park Dr.
Woodbury, New York 11797 Rev2 1/2004
HKTS5/HKTS6 harman/kardon
- CONTENTS -
BASIC SPECIFICATIONS.........................................................1
DETAILED SPECIFICATIONS ...............................................2
CONNECTIONS.......................................................................3
OPERATION ..........................................................................4
TROUBLESHOOTING..............................................................5
SUB-TS5/TS6 EXPLODED VIEW.................................................6
SUB-TS5/TS6 AMPLIFIER EXPLODED VIEW....... ..........................7
SUB-TS5/TS6 TEST PROCEDURE............................ ..................8
HKTS 5/HKTS 6 MECHANICAL/SATELLITE PARTS LIST...............9
HKTS 5/HKTS 6 PACKAGE........................................................10
SUB-TS5/ TS6 BLOCK DIAGRAM........................... ..................11
SUB- TS5/ TS6 PCB DRAWINGS.................................................12
SUB- TS5/ TS6 ELECTRICAL PARTS LIST ..................................15
SUB- TS5/ TS6 IC/TRANSISTOR PINOUTS.................................18
SUB- TS5/ TS6 SCHEMATICS....................................................19
HKTS 5/HKTS6 System Frequency Response
35Hz 20kHz (6dB)
Satellites Center Subwoofer SUB-TS5/TS6
Recommended Power Recommended Power Amplifier
10 70 watts 10 70 watts 100 watts RMS
Impedance Impedance Woofer
8 ohms nominal 8 ohms nominal 10" woofer, bass-reflex enclosure
Sensitivity Sensitivity Dimensions (H x W x D)
86dB @ 1 watt/1 meter 86dB @ 1 watt/1 meter 15-3/4" x 15-3/4" x 16-3/4"
Tweeter Tweeter (400mm x 400mm x 425mm)
One 1/2" dome, video-shielded One 1/2" dome, video- Weight
Midrange shielded 33.5 lb/15.2kg
One 3" driver, video-shielded Midrange
Dimensions (H x W x D) Dual 3" drivers, video-
4-5/8" x 3-1/8" x 3-3/4" shielded
(117mm x 79mm x 93mm) Dimensions (H x W x D)
Weight 3-1/2" x 7-5/8" x 3-3/4"
1.1 lb/0.5kg (89mm x 194mm x 93mm)
Weight
1.89 lb/0.86kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
HKTS5/HKTS6 harman/kardon
SUB-TS5/TS6 Amplifier 100w Powered Subwoofer Amplifier
LINE VOLTAGE Yes/No Hi/Lo Line Unit Notes
US 120vac/60Hz Yes 108-132 Vrms Normal Operation
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (Class AB, D, other) AB AB n/a External Sink required for Class AB
Load Impedance (speaker) 4 Ohms n/a Nominal Z-curve required
Rated Output Power 100 Watts 95 1 input driven
THD@ Rated Power 0.08 % 0.3 22k filter
THD @ 1 Watt 0.1 % 0.5 22k filter
DC Offset 10 mV-DC 20 @ Speaker Outputs
Damping factor >100 DF 50 Measured at speaker terminals, Output
power 90 Watts THD 0.1 %
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq. 1 input driven
SUB Input 135 mVrms ±2dB To Rated Power SUB input driven only
Signal to Noise
SNR-A-Weighted 100 dBA 90 rel. to rated power A-Weighting filter
SNR-unweighted 80 dBr 75 rel. to rated power 22k filter
SNR @ 1W-unweighted 60 dBr 55 rel. to 1W Output 22k filter
Residual Noise Floor 1.5 mVrms 2.5 Volume @max, using RMS reading
DMM/VOM (or A/P)
Residual Noise Floor 1 mVrms(max) 2 Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Input Impedance
SUB Line input >15 K ohms n/a Nominal
Filters
Low Pass (fixed or variable) fixed -- ±2dB
Slope & Q dB/Octave n/a
Subsonic filter (HPF) Hz ±2dB
Slope & Q dB/Octave n/a
Limiter (yes/no) YES -- n/a
Features
LFE Input YES functional BW Limited to 500 Hz
Phase Switch (yes/no) NO -- functional
Volume pot Taper (lin/log) log -- functional
ATO YES functional
Input Configuration
SUB Line level LFE functional Single RCA Input
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES -- functional
ATO Input Frequency 50 Hz functional
ATO Level 2 mV functional 2mV@50Hz into Line Input w/ 1 ch.
driven
ATO Turn-on time 5 ms functional Amp connected and AC on, then input
signal applied
Auto Mute/ Turn-OFF Time 15 minutes functional T before muting, after signal is removed Auto turn of time (T) must be 10 > T <15
Power on Delay time 3 sec. functional AC Power Applied
Transients/Pops
ATO Transient 5 mV-peak 10 @ Speaker Outputs
Turn-on Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from ON to OFF
Efficiency
Stand-by Input Power 13 Watts 15 @ nom. line voltage Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
Power Cons.@rated power 185 Watts 195 @ nom. line voltage 100 Watts @ 4 Ohms nominal line voltage
Protection
Short Circuit Protection YES -- functional Direct short at output
Thermal Protection 65 deg. C -- functional @1/8 max unclipped Power Temperature rise should not exceed 35K
rise
DC Offset Protection YES -- functional DC present at Speaker Out leads Relay or crowbar (for driver/fire protection)
Line Fuse Rating 2.5 Amps 2.5 Type-T or Slo Blo External fuse with UL/SEMKO rated holder
2
HKTS5/HKTS6 harman/kardon
SPEAKER CONNECTIONS
Use the supplied RCA-type patch cord to
connect the line-level SUB or LFE output on
your receiver or amplifier to the SUB input
on the SUB-TS5 or SUB-TS6 subwoofer.
Connect the satellite and center speakers to
the corresponding speaker terminals on your
receiver or amplifier.
Make sure that you have configured your
surround sound processor for "Subwoofer
On." The front left, front right, center and
rear speakers should all be set to "Small."
When all connections have been made, plug Left Center Right
the AC power cord on the subwoofer into +
Front Front
an AC outlet. + +
SUBTS5/TS6
Subwoofer
Line-Level
SUB Input
Left Right
Front Front
SUB/LFE
Out
Left Right
Rear Center Rear
Left Right
Surround Surround
+ Receiver +
3
HKTS5/HKTS6 harman/kardon
OPERATION
Move the Master Power switch (marked When your receiver or amplifier is off, or is When the Auto/On switch TM is switched to
"Power" ”) to the "·" (On) position. The not sending program material to the sub- the "On" position, the subwoofer will
HKTS 5/6 subwoofer will automatically turn woofer, the subwoofer will be in Standby remain on, whether or not program material
itself on or go into Standby mode, depend- mode and the LED ¢ on the amp panel is playing.
ing on whether or not a signal is being sent will turn red. When the subwoofer senses an If you will be away from home for an
to the HKTS 5/6 by your receiver or surround audio signal, it will automatically turn itself extended period of time, or if the sub-
processor, and provided that the Auto/On on and the LED ¢ will turn green. If the woofer will not be used, switch the Master
switch TM is moved to the left so that it is subwoofer does not sense a signal after Power switch ” to the "Off" position.
in the "Auto" position. approximately twenty minutes, it will auto-
matically go into Standby mode.
TM £
¢
SUB-TS5/SUB-TS6
”
Volume
Volume can be adjusted using the
Subwoofer Level Control £, as shown
below.
Subwoofer Subwoofer
Level Level
MIN MAX MIN MAX
4
HKTS5/HKTS6 harman/kardon
TROUBLESHOOTING
If there is no sound from any of the If there is no sound from the center If there is no sound from the sur-
speakers: speaker: round speakers:
· Check that receiver/amplifier is on and a · Check all wires and connections between · Check all wires and connections between
source is playing. receiver/amplifier and speaker. Make sure receiver/amplifier and speakers. Make sure
· Check that the powered subwoofer is all wires are connected. Make sure none all wires are connected. Make sure none
plugged in and its Power switch ” is of the speaker wires are frayed, cut or of the speaker wires are frayed, cut or
switched on to the "·" position. punctured. punctured.
· Check all wires and connections between · If your receiver/processor is set in Dolby · Review proper operation of your
receiver/amplifier and speakers. Make sure Pro Logic* mode, make sure the center receiver/processor and its surround sound
all wires are connected. Make sure none speaker is not in phantom mode. features.
of the speaker wires are frayed, cut or · If your receiver/processor is set in Dolby · Make sure the movie or TV show you are
punctured. Digital or DTS mode, make sure the watching is recorded in a surround sound
· Review proper operation of your receiver/processor is configured so mode. If it is not, check to see whether your
receiver/amplifier. that the center speaker is enabled. receiver/processor has other surround
modes you may use.
If there is no sound coming from one If the system plays at low volumes · In Dolby Digital or DTS mode, make sure
speaker: but shuts off as volume is increased: your receiver/processor is configured so that
· Check the "Balance" control on your · Check all wires and connections between the surround speakers are enabled.
receiver/amplifier. receiver/amplifier and speakers. Make sure · Review the operation of your DVD player
· Check all wires and connections between all wires are connected. Make sure none and the jacket of your DVD to make sure
receiver/amplifier and speakers. Make sure of the speaker wires are frayed, cut or that the DVD features the desired Dolby
all wires are connected. Make sure none punctured. Digital or DTS mode, and that you have
of the speaker wires are frayed, cut or · If more than one pair of main speakers is properly selected that mode using both
punctured. being used, check the minimum impedance the DVD player's menu and the DVD
requirements of your receiver/amplifier. disc's menu.
· In Dolby* Digital or DTS® mode, make
sure that the receiver/processor is config-
ured so that the speaker in question is If there is low (or no) bass output:
enabled. · Make sure the SUB input of the SUB-TS5/6
· Turn off all electronics and switch the subwoofer and SUB or LFE output of your
speaker in question with one of the other receiver or amplifier are properly connected
speakers that is working correctly. Turn by the RCA-type patch cord.
everything back on, and determine whether · Make sure the connections to the Speaker
the problem is in the same place: i.e., the Inputs have the correct polarity (+ and ).
speaker that was working previously now · Make sure the subwoofer is plugged
has no sound and the speaker that was not into an active electrical outlet and its
working now sounds fine; or whether it has Power switch ” is switched on to the
moved: i.e., the speaker that was not work- "·" position.
ing still has no sound and the speaker that · Check the speaker setup (bass manage-
was working is still fine. If the problem is in ment) settings in your AVR receiver or
the same place, the source of the problem processor to make certain that the front,
is most likely with your receiver or amplifier, center and surround speakers are config-
and you should consult the owner's manual ured for "Small," and that the subwoofer is
for that product for further information. If the set for "Yes" or "On."
problem has followed the speaker, consult
your dealer for further assistance or, if
that is not possible, visit our Web site at
www.harmankardon.com for further
information.
5
HKTS5/HKTS6 harman/kardon
Ref. Part Number Description Qty
#1 Not For Sale HKTS5/HKTS6 Enclosure 1
#2 (HKTS5) sz5321 HK Logo 1
(HKTS6) sz5930 HK Logo 1
#3 25MF10DZB-DW02 10" woofer (DCR = 3.4 ohms ±10%) 1
#4 06-t4205012 Amplifier/woofer screw t4*20 15
#5 wi5448 Foot (bumper) 4
#6 06-t5345005 Foot screw 4
#7 wi5447 Rubber foot 4
#8 wi5600 Port Tube 1
#9 Not For Sale HKTS5/HKTS6 Amplifier Assembly 1
6
7
HKTS5/HKTS6 harman/kardon
HKTS 5/HKTS 6 TEST PROCEDURE
Equipment needed:
· Function/signal generator/sweep generator
· Integrated Amplifier
· Multimeter
· Speaker cables
· Single RCA cable
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the single SUB input.
2) On the front of the unit, turn the LEVEL control full counterclockwise.
3) Turn on generator, adjust to 150mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)
5) LED should now be Green; immediate bass response should be heard and felt from port tube opening.
6) Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cable.
Sweep Function
1) Follow steps 3-6 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any
other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
5) Caution: when re-connecting woofer wires, observe proper polarity, as Faston connectors are the same size;
red wire should connect to terminal with red dot.
8
HKTS5/HKTS6 harman/kardon
MECHANICAL/SATELLITE PARTS LIST
Part number Description
SATELLITES
HKTS 5/SAT-TS5 Complete satellite loudspeaker
HKTS 6/SAT-TS6 Complete satellite loudspeaker
22PF48JA-FW02 Woofer for Sats
g255002 grille
sz5322 logo for HKTS 5/SAT-TS5
sz5928 logo for HKTS 6/SAT-TS6
xc255002 front enclosure
xd255000 back enclosure
wi0409 Wall-mount bracket for HKTS 5/SAT-TS5
wi5969 Wall-mount bracket for HKTS 6/SAT-TS6
CENTER
HKTS 5/CEN-TS5 Complete Center loudspeaker
HKTS 6/CEN-TS6 Complete Center loudspeaker
22PF48JA-DW06 Woofer for Center
g255003 grille
xc255001 front enclosure
xd255001 back enclosure
sz5371 logo for HKTS 5/CEN-TS5
sz5929 logo for HKTS 5/CEN-TS6
SUB-TS5/TS6 SUBWOOFER EXTERNAL & HKTS5/HKTS6 PACKAGING
25MF10DZB-DW02 10" woofer
wi5447 Rubber foot (4)
wi5448 foot (4)
sz5321 logo
ai5161 Owner's manual (HKTS5)
ai5262 Owner's manual (HKTS6)
wg5296 Outer carton (HKTS5)
wg5452 Outer carton (HKTS6)
at5073 warranty card
wp5215 Foam set
sal063-1 Wire set 20' (center)
sal5009 Wire set 40' (surround)
sal5020 Wire set 15' (front satellites)
sal5044 Single RCA cable
OPTIONAL: Floor Stands for HKTS 5/SAT-TS5 satellites - FSTS1
9
HKTS5/HKTS6
Packaging
5
HKTS5/HKTS6 harman/kardon
11
HKTS5/HKTS6 harman/kardon
12
HKTS5/HKTS6 harman/kardon
13
HKTS5/HKTS6 harman/kardon
14
HKTS5/HKTS6 harman/kardon
SUB-TS5/TS6 Electrical Parts List
PART NO. DESCRIPTION QTY Reference Designator
Resistors
11014152j26 RESISTOR 1.5K 1/4W ±5% CF 1 R265
11014472j26 RESISTOR 4.7K 1/4W ±5% CF 2 R147,150
11014681j26 RESISTOR 680 ohms 1/4W ±5% CF 2 R148,151
11016101j26 RESISTOR 100 ohms 1/6W ±5% CF 2 R120,215
11016102j26 RESISTOR 1K 1/6W ±5% CF 2 R124,254
11016103j26 RESISTOR 10K 1/6W ±5% CF 8 R134,230,232,235,237,240,260,264
11016105j26 RESISTOR 1M 1/6W ±5% CF 2 R143,259
11016123j26 RESISTOR 12K 1/6W ±5% CF 2 R135,139
11016124j26 RESISTOR 120K 1/6W ±5% CF 1 R233
11016151j26 RESISTOR 150 ohms 1/6W ±5% CF 1 R253
11016152j26 RESISTOR 1.5K 1/6W ±5% CF 6 R103,123,136,137,141,142
11016153j26 RESISTOR 15K 1/6W ±5% CF 5 R118,145,152,154,234
11016154j26 RESISTOR 150K 1/6W ±5% CF 2 R131,252
11016181j26 RESISTOR 180 ohms 1/6W ±5% CF 2 R111,114
11016182j26 RESISTOR 1.8K 1/6W ±5% CF 1 R153
11016183j26 RESISTOR 18K 1/6W ±5% CF 2 R238,262
11016205j26 RESISTOR 2.0M 1/6W ±5% CF 1 R257
11016223j26 RESISTOR 22K 1/6W ±5% CF 5 R128,129,133,255,263
11016332j26 RESISTOR 3.3K 1/6W ±5% CF 3 R106,107,144
11016392j26 RESISTOR 3.9K 1/6W ±5% CF 2 R105,108
11016393j26 RESISTOR 39K 1/6W ±5% CF 1 R126
11016470j26 RESISTOR 47 ohms 1/6W ±5% CF 4 R112,113,115,116
11016471j26 RESISTOR 470 ohms 1/6W ±5% CF 1 R140
11016472j26 RESISTOR 4.7K 1/6W ±5% CF 4 R110,125,130,258
11016473j26 RESISTOR 47K 1/6W ±5% CF 4 R101,219,250,251
11016560j26 RESISTOR 56 ohms 1/6W ±5% CF 1 R117
11016563j26 RESISTOR 56K 1/6W ±5% CF 1 R104
11016682j26 RESISTOR 6.8K 1/6W ±5% CF 1 R109
11010821jk1 RESISTOR 820 ohms 1W ±5% 1 R132
110122r2j15 RESISTOR 2.2 ohms 1/2W ±5% 1 R127
11016332j26 RESISTOR 3.3K 1/6W ±5% CF 1 R266
11020331jk2 RESISTOR 330 ohms 2W ±5% 1 R146
11020331jk3 RESISTOR 330 ohms 2W ±5% 1 R149
11350r10j20 CEMENT RESISTOR 0.1 ohms 5W ±5% 2 R121,122
11403302m0 POT 3K 0.3W ±20% 1 R138
115h503a101 VARIABLE RESISTOR D16 50K/1 A 1 VR201
15
HKTS5/HKTS6 harman/kardon
PART NO. DESCRIPTION QTY Reference Designator
Capacitors
1302b101k503 100pf 50V ±10% 1 C220
1302b102k503 1000pf 50V ±10% 1 C116
1302b221k503 220pf 50V ±10% 2 C212,230
1302f104z503 0.1uf 50V +80/-20% 9 C108,113,115,119,232,236,237,240,241
1303f473m503 0.047uf 50V ±20% 1 C106
130sl470k503 47pf 50V +350/-1000 ±10% 1 C229
132104j503 0.1uf 50V ±5% 4 C107,221,222,224
132223ja03 0.022uf 100V ±5% 4 C124,125,126,128
132473j503 0.047uf 50V ±5% 1 C223
1353105m50 1uf 50V 3 C105,112,228
1353106m50 10uf 50V 2 C219,231
1353107m16 100uf 16V 6 C109,117,120,234,238,242
1353226m50 22uf 50V 2 C114,118
1353227m10 220uf 10V 2 C129,130
1353227m16 220uf 16V 2 C111,233
1353476m25 47uf 25V 1 C103
1302g472md00 4700pf 400V ±20% 1
132223ja03 0.022uf 100V ±5% 2 C123,127
1353107m16 100uf 16V 1 C110
1353226m50 22uf 50V 1 C225
1354688m50 6800uf/50V 2 C121,122
Semiconductors
192027c1815gr 2SC1815GR NPN TRANS 8 Q102,111,112,113,118,206,207,208
192028a1015gr 2SA1015GR PNP TRANS 2 Q114,116
1921672n5551 2N5551 NPN TRANS 2 Q103,109
1921682n5401 2N5401 PNP TRANS 2 Q104,110
197131n4148 1N4148 9 D101,103,105,108,206,207,208,214,215
19915000335 3.3V 1/2W ZENER 2 D102,205
19915000625 6.2V 1/2W ZENER 2 D106,107
19915001605 16V 1/2W ZENER 1 D109
19016tl074cn TL074CN QUAD OP-AMP 1 U202
192011d669a 2SD669A NPN TRANS 1 Q106
192012b649a 2SB649A PNP TRANS 1 Q105
192021c1815gr 2SC1815GR NPN TRANS 2 Q101,115
192021tip35c TIP35C NPN TRANS 1 Q107
192022tip36c TIP36C PNP TRANS 1 Q108
192201d882y KSD882Y NPN TRANS 1 Q117
192202b772y KSB772Y PNP TRANS 1 Q119
19006m4558d OPA 4558D DUAL OP-AMP 2 U101,203
16
HKTS5/HKTS6 harman/kardon
PART NO. DESCRIPTION QTY Reference Designator
19510204hgw LED 204HGW 1 D209
19700kbl405 4A 500V KBL405 BRIDGE 1 D110
197101n4002 1N4002 1 D104
Miscellaneous
171udhss124d 5A 24V UDH-SS124D RELAY 1 RY101
1740rcb242vpg JACK RCB 1 JK203
180tms7210v SWITCH SLIDE MS7210V 1 SW201
150e8604107 TRANSFORMER 1
152u602015 LINE CORD SVT FT-2 6FT 1
154u25006t0 FUSE 2.5A 250V 20mm 1 FS101
155520020 FUSE HOLDER R3-11 1
180pbr12c11s PUSH SW BR12C11S 1 SW101
LIMITER PCB
11016103j26 RESISTOR 10K 1/6W ±5% CF 7 R301,302,303,304,308,309,314
11016223j26 RESISTOR 22K 1/6W ±5% CF 2 R310,312
11016333j26 RESISTOR 33K 1/6W ±5% CF 1 R305
11016474j26 RESISTOR 470K 1/6W ±5% CF 1 R307
11016751j26 RESISTOR 750 ohms 1/6W ±5% CF 2 R311,313
11016755j26 RESISTOR 7.5M 1/6W ±5% CF 1 R306
1302f104z503 0.1uf 50V +80/-20% 2 C305,306
132103j503 0.01uf 50V ±5% 2 C302,3
1353226m50 22uf 50V ±20% 1 C301
1353476m25 47uf 25V ±20% 1 C304
192027c1815gr 2SC1815GR B91 2 Q301,302
197131n4148 1N4148 2 D301,302
1759f40hr2 40PIN PITCH=2.54mm HR2*4 0.15 P301
19016tl074cn TL074CN QUAD OP-AMP 1 U301
17
HKTS5/HKTS6 harman/kardon
18
HKTS5/HKTS6 harman/kardon
19
HKTS5/HKTS6 harman/kardon
20
HKTS5/HKTS6 harman/kardon
21