Text preview for : HarmanKardon-SUBTS15 actsub.pdf part of Harman/Kardon SUBTS15 active subwoofer
Back to : HarmanKardon-SUBTS15 acts | Home
harman/kardon
(HKTS 15 SUBWOOFER)
SUB-TS15
SERVICE MANUAL
harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 2/2007
SUB-TS15
harman/kardon
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . . . . ........................................... . . . 1 DETAILED SPECIFICATIONS. . . . . . . . . . . . . .. . . . . . . . . ....................... ...2 PACKAGING. . . . . . . . . . . . . .. . . . . . . ........................... . . . . .. . .. .. .. . . . . 4 CONTROLS & CONNECTIONS . . . . . . . . . . . . . .. . . . . . . . . ....................... 5 SPEAKER CONNECTIONS.............................................. . . .. . .. . . . .. . . 7 OPERATION....... . . . . .. . . . . . . . .. .. . . . .. .. . . . . ....................................10 TEST PROCEDURE. . . . . . . . . . . ..........................................................11 UNIT EXPLODED VIEW. . . . ............... ................ .. ............ . . .. .. ... . ... . 12 AMPLIFIER EXPLODED VIEW. . . . ..................... . .. ............ . . .. . . .. . .... . 13 BLOCK DIAGRAM . . . . . . . . . . . . . .. . . . . . . .................. . . . . .. . .. . .. . . . . 14 DETAILED TROUBLESHOOTING...........................................................16 PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ......... . ............. . . . .. .. .. . .. . . . 17 ELECTRICAL PARTS LIST ............. .... . .. . . . ................................. ... . . 23 SEMICONDUCTOR PINOUTS . . . .. .. .. .. . . . .. . ...................................... .27 SCHEMATIC DIAGRAMS . . . . . . . . .. .. .. .. . . . .. . .................................... .28
SPECIFICATIONS
Amplifier Power (RMS) Driver Inputs Outputs Frequency Response External Trigger Input Voltage: Dimensions (H x W x D) Weight 100 Watts 10" (254mm) woofer, Bass Reflex Enclosure Stereo Line Level, dedicated Subwoofer (LFE) and Speaker Level with gold-plated binding posts Speaker Level with gold-plated binding posts 35Hz 120Hz (Filter switch ON) 35Hz 450Hz (Filter switch OFF) 3-30 Volts AC/DC 18-7/8" x 13-3/8" x 13-3/8" (479mm x 340mm x 340mm) 35.11 lb/15.8kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated.
1
SUB-TS15
SUB-TS15 100W Powered Sub/ Plate Amp
LINE VOLTAGE US 120vac/60Hz Parameter Amp Section Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power THD @ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity Input Frequency Line (L&R) Input SUB (LFE) Input Speaker/Hi Level Input Hi Level Max. Input Voltage Signal to Noise SNR-A-Weighted SNR-unweighted SNR rel. 1W-unweighted Residual Noise Floor Residual Noise Floor Input Impedance Line Input (L, R,LFE) Speaker/Hi Level Input Filters L&R Fixed Low-Pass Filter SUB (LFE) Low pass Filter Subsonic filter (HPF) 3rd Order Limiter THD at Max. Output Power Features Auto - On -Off Selection Switch Phase Switch Filter On/Off Switch Volume Pot Taper (Lin/Log) Speaker Out 2-Color LED power indicator Power Switch Fuse Holder Input Configuration Line In (L,R) SUB (LFE) Speaker/Hi Level In AB 4 100 0.08 0.15 5 >100 50 220 125 2.2 32 100 90 65 1.2 0.8 10K 4.7K 170 270 28 2.0 YES 0-180 YES LOG YES YES YES YES n/a Ohms Watts % % mV-DC n/a Hz mVrms mVrms Vrms Vrms dB dB dB mVrms mVrms ohms ohms Hz Hz Hz % n/a n/a 75 0.1 0.5 30 30 n/a 154 - 308 87 - 175 1.5 - 3.0 30 85 80 60 3.0 2.0 n/a n/a Yes/No Yes Nonimal Specification Hi/Lo Line 108-132 Unit Nom. 120 QA Test Limits Unit Vrms Conditions
harman/kardon
Notes Normal Operation Notes
Nominal 50 - 250 Hz, 1 input driven, limiter off 22k filter 22k filter @ Speaker Outputs Measured at amplifier board Nominal Freq. To Rated Power To Rated Power To Rated Power Nominal Freq., Min. Volume relative to rated power relative to rated power relative to 1W Output Volume @max, using RMS reading DMM/VOM (or A/P) Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) Nominal Nominal
Measured at the speaker at speaker output terminals on the amp board.
Single input driven SUB (LFE) input driven only (20 dB below Line In), Single input driven
A-Weighting filter 22k filter 22k filter
150 - 200 @ -6dB ref. 100Hz 240 - 300 @ -3dB ref. 100Hz 22 - 28 @ -3dB ref. 30Hz 5.0 functional functional functional functional functional functional functional functional
2nd order fixed 2nd order fixed 3rd order fixed
deg
Refer to ATO section A Taper Binding post connector L&R Blue: On, Amber: Stand-by
YES
YES YES
functional
functional functional
Dual RCA jack RCA jack
Binding post connector L&R
Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level Line & SUB Input ATO Level Speaker in ATO Turn-on time ATO Turn-OFF Time Power on Delay time Transients/Pops ATO Transient Turn-on Transient
YES 50 4.0 40 5 15 3 5 50
Hz mV mV ms minutes sec. mV-peak mV-peak
functional n/a 2.0 - 6.0 25 - 55
Auto - on selection switch in Auto Auto - on selection switch in Auto Auto - on selection switch in Auto Auto - on selection switch in Auto Amp connected and AC on, then input functional signal applied Time before muting, after signal is 10 - 20 removed
functional AC Power Applied 10 100 @ Speaker Outputs @ Speaker Outputs
AC Line cycled from OFF to ON
2
SUB-TS15
Nonimal Specification 50 QA Test Conditions Limits 100 @ Speaker Outputs
harman/kardon
Unit mV-peak Notes AC Line cycled from ON to OFF Maximum allowable input power under nominal input voltage and frequency, in stand-by mode (HOT or COLD operation). 100 Watts @ 4.0 ohms and nominal line voltage Amplifier should resume operation after short circuit condition is removed. Any user accessible metal parts should always remain at 65 degree C or less for domestic version or 55 degree C or less for EU version. Relay or crowbar (for driver/fire protection), User-replacable fuse with UL/SEMCO rated holder.
Parameter Turn-off Transient Efficiency
Stand-by Input Power Power Consumption @ rated powe Protection Short Circuit Protection
10 170
Watts Watts
12 200
@ nom. line voltage @ nom. line voltage
YES
functional Direct short at output
Thermal Protection DC Offset Protection Primary Fuse Rating USA-Domestic (120V)
YES YES 2.5 Amps
functional functional DC present at Speaker Out leads n/a Type-T or Slo Blo
3
SUB-TS15
harman/kardon
PACKAGE
Item
1 5 2 3 4
1 2
Description
Color Label Warranty Card Warranty Card Owner's Manual Packaging Packaging Non-woven Bag PE Bag Non-woven Bag PE Bag Cardboard Wall Mounting Bracket Mounting Plate Leather Coaster for Sats Metal Bracket (Center) Screw Bag for CEN Wall Bracket Terminal Cap 15ft RCA Signal Cable E 1 2 4 4 0
Part Number
Qty
1.0 1.0 1.0 1.0
1.0 1.0
405-000-00333-E 405-000-05033-E 406-000-05503-E
SAT 5
12 13 14 15 16 17 18 19 20 21 22 23 24
3 4 5 6 7 8 9 10
7
8
11 CEN 6 9 10
6
4.0 4.0 1.0 1.0 1.0
26
11 12 13 14
326-ABS-00108-0BAE 326-FE-00109-E
4.0
4.0 4.0
1.0
336-EVA-05405-0BAE
27
15 16 17 18 19
325-SPCC-05229-0BAE
371-000-05168-E
1.0 4.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
1.0
317-PS-00172-0BAE
370-000-05034-E
Speaker Cable 20ft. (Red) 370-000-05035-E Speaker Cable 20ft. (Grn) 370-000-05036-E Speaker Cable 20ft. (Wht) 370-000-05037-E Speaker Cable 12M (Gry) 370-000-05038-E Speaker Cable 12M (Blu) 370-000-05039-E
SUB
20
29 30
21 22 23 24 25
Screw Bag for S SAT Wall Bracket
Signal Cable for Trigger Inner Carton for Sat, Ctr
371-000-00360-E 165-54505501-e 401-000-00118-E 431-000-05919-E 431-000-05920-E
2
28 31
26 27 28 29 30 31 32
1.0
Top Packing Bottom Packing
Non-woven Bag PO Bag Dessicant Outer Carton
1.0 1.0 1.0 1.0 2.0
4 3 402-000-05679-E
1.0
32
.
371-000-05168-E: 2pcs Flat head, 10mm( screw Length ) x 8mm(Screw head Dim.) 371-000-00360-E: 2pcs Round head, 1/4"( screw Length ) x 10.5mm(Screw head Dim.)
4
SUB-TS15
harman/kardon
SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
¡ Subwoofer-Level Control TM High-Cut (Low-Pass) Filter Switch £ External Trigger Input ¢ Audio-Sense On/Off Switch
Phase Switch § Line-Level Subwoofer (SUB) Input ¶ Line-Level Full-Range Inputs · Speaker-Level Outputs
ª Speaker-Level Inputs , Master Power Switch / AC Power Cord
¡ Subwoofer-Level Control: Volume may be adjusted using the SubwooferLevel Control. Turn the control clockwise to increase the SUB-TS15's volume, or counterclockwise to decrease it. TM High-Cut (Low-Pass) Filter Switch: Placing this switch in the ON position activates circuitry that cuts out all audio input signals above 120Hz. This allows the SUBTS15 to focus its power on reproducing the low-frequency portion of the signal, avoiding
inefficiency and distortion. Engage this filter when using the Speaker-Level Inputs ª, or when using the Line-Level Full-Range Inputs ¶, unless your receiver or processor processes its line-level output using a lowpass filter. The filter has no effect when the SUB Input § is used. £ External Trigger Input: Use the supplied mini-plug cable to connect the trigger output of another compatible product to this jack. Whenever a trigger signal between
3 and 30 volts (AC or DC) is detected, the SUB-TS15 amplifier will turn on, even when the Audio-Sense feature has been activated by placing the Audio-Sense On/Off Switch ¢ in the AUTO position. The amplifier will remain on for about 1015 minutes without a trigger signal. ¢ Audio-Sense On/Off Switch: When placed in the AUTO position, and when the Master Power Switch , is turned on, the SUB-TS15 will automatically turn itself on or
5
SUB-TS15
harman/kardon
SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
place itself in the Standby mode, depending on whether it is receiving an audio signal. When this switch is placed in the ON position, the SUB-TS15 will remain on, whether or not it is receiving an audio signal. An LED located on top of the SUB-TS15 indicates whether the SUB-TS15 is in the ON or STANDBY state when used with the Audio-Sense On/Off Switch ¢ in the AUTO position. The LED is lit blue to indicate that the SUB-TS15 is receiving an audio signal and is turned on, and the LED is lit amber to indicate that no signal is being received and the SUB-TS15 is in Standby mode. When the Audio-Sense On/Off Switch ¢ is in the ON position, the LED will be lit blue, whether or not an audio signal is present. When the Master Power Switch , is turned off, the LED goes dark, no matter which position the Audio-Sense On/Off Switch ¢ is in. Phase Switch: This switch determines whether the SUB-TS15 subwoofer's pistonlike action moves in and out in phase with the main speakers. If the speakers were to play out of phase, the sound waves produced by the subwoofer would be cancelled out, reducing bass response. This phenomenon depends in part on the relative placement of the speakers in the room. In most cases, the Phase Switch should be left in the NORMAL position. However, it does no harm to experiment with the Phase Switch , and you may leave it in the position that maximizes bass response. § Line-Level Subwoofer (SUB) Input: Connect the subwoofer output of a receiver with digital surround sound decoding, such as Dolby® Digital or DTS,® to this input. This input bypasses the SUB-TS15's internal crossover circuitry, and should only be used with a filtered signal. If your receiver does not have digital decoding, you should use the Line-Level Full-Range Inputs ¶ instead. ¶ Line-Level Full-Range Inputs: Connect the line-level subwoofer output or preamp output(s) of your receiver or amplifier to these inputs. If your receiver does not have a separate subwoofer output, use a Y-adapter (not supplied) to bridge the receiver's preamp output to the main amp input for that channel, and connect the long end of the adapter to the corresponding line-level input on the SUB-TS15. If your receiver has only a single subwoofer output, you may connect it to either the left or right line-level input on the SUB-TS15, and no Y-adapter is needed. · Speaker-Level Outputs: If you are using the Speaker-Level Inputs ª on the SUB-TS15, you should connect these binding-post terminals to your front left and right speakers, remembering to maintain polarity by connecting the (+) terminal on the SUBTS15 subwoofer to the (+) terminal on the speaker, and the () terminal on the SUBTS15 subwoofer to the () terminal on the speaker. If you are not using the SpeakerLevel Inputs ª, then connect your front left and right speakers directly to your receiver or amplifier. See pages 9 through 12 for further information on speaker connections. ª Speaker-Level Inputs: If your receiver or amplifier does not have a line-level subwoofer output, connect these binding-post terminals to the main left and right speaker terminals of your receiver or amplifier. Remember to maintain polarity by connecting the (+) terminal on the receiver/amplifier to the (+) terminal on the SUB-TS15 subwoofer, and the () terminal on the receiver/amplifier to the () terminal on the SUB-TS15 subwoofer. , Master Power Switch: Place this switch in the "·" position to power-on the SUB-TS15 subwoofer. The SUB-TS15 will then be either in the Standby mode or completely on, depending on the position of the Audio-Sense On/Off Switch ¢. / AC Power Cord: Make sure to plug this cord into an active, unswitched electrical outlet for proper operation of the SUB-TS15. The cord should not be plugged into the accessory outlets found on some audio components.
6
SUB-TS15
harman/kardon
SPEAKER CONNECTIONS
Dolby ® Digital or DTS® (or Other Digital Surround Mode) Connection
USE THIS INSTALLATION METHOD FOR DOLBY DIGITAL, DTS OR OTHER DIGITAL SURROUND PROCESSORS: Use the line-level input jack marked SUB § for the Low-Frequency Effects channel. Connect this jack to the subwoofer output or LFE output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure you've configured your surround sound processor for "Subwoofer On. The " front left, front right, center and surround speakers should all be set to "Small. " When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front Left SUB/LFE Out Surround Left Center Surround Right
Front Left +
Center +
Front Right +
SUB-TS15 Subwoofer
LINE LEVEL IN SUB R L
Front Right
Surround Left +
Receiver
Surround Right +
7
SUB-TS15
harman/kardon
SPEAKER CONNECTIONS
Dolby Pro Logic® (Non-Digital) Line Level
USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR IS EQUIPPED WITH A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Use the supplied RCA-type interconnect cable to connect the line-level subwoofer output on your receiver or amplifier to either the left or right Line-Level Full-Range Input ¶ on the SUB-TS15 subwoofer. Use both the left and right inputs on the subwoofer if your receiver or processor has both left and right line-level outputs. In that case, you will need to supply a second interconnect cable. If your receiver is equipped with line-level outputs but does not have a separate subwoofer output, use a Y-adapter (not supplied) to bridge the receiver's preamp output to the main amp input for that channel, and connect the long end of the adapter to the corresponding line-level input on the SUB-TS15. IMPORTANT: Do not use the SUB Input § on the subwoofer with Dolby Pro Logic processors. If your receiver/processor has a built-in lowpass-crossover filter for the subwoofer output, you may use the SUB Input § to bypass the subwoofer's internal crossover. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround sound processor for "Subwoofer On. The front left, front right, center and " surround speakers should all be set to "Small. " When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front Left +
Center +
Front Right +
SUB-TS15 Subwoofer Line-Level R L
Front Left SUB/LFE Out Surround Left Center
Front Right
Surround Right
Surround Left +
Receiver
Surround Right +
8 SPEAKER CONNECTIONS 11
SUB-TS15
harman/kardon
SPEAKER CONNECTIONS
Dolby Pro Logic (Non-Digital) Speaker Level
USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR DOES NOT HAVE A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Connect your receiver or amplifier's front left and right speaker terminals to the left and right Speaker-Level Input ª terminals on the SUB-TS15 subwoofer that are marked "High Level In." Connect the left and right Speaker-Level Output · terminals on the SUB-TS15 subwoofer that are marked "High Level Out" to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifier's center and surround left and right speaker terminals to the corresponding terminals on the back of your center, and surround left and right speakers. When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front Left
Center
+
+
Front Right
+
SUB-TS15 Subwoofer
H I G H L E V E L
L
R
Receiver
Front Left Center Front Right
Surround Left
Surround Right
Surround Left
Surround Right
+
+
9
SUB-TS15
harman/kardon
OPERATION
Move the Master Power Switch , (marked Power) to the "·" (On) position. The SUB-TS15 subwoofer will automatically turn itself on or go into Standby mode, depending on whether or not a signal is being sent to it by your receiver or surround processor, and provided that the AudioSense On/Off Switch ¢ is moved down so that it is in the AUTO position. When your receiver or amplifier is off, or is not sending program material to the subwoofer, the subwoofer will be in Standby mode and the LED Indicator on the top of the subwoofer will turn amber. When the subwoofer senses an audio signal, it will automatically turn itself on and the LED Indicator will turn blue. If the subwoofer does not sense a signal after approximately twenty minutes, it will automatically go into Standby mode. When the Audio-Sense On/Off Switch ¢ is switched to the ON position, the subwoofer will remain on, whether or not program material is playing, and the LED Indicator will remain lit blue. If your receiver, processor or amplifier is equipped with a compatible trigger output, you may connect it to the SUB-TS15's External Trigger Input £. When you turn on your component, if you have set it up correctly, it will send an electrical trigger signal to the SUB-TS15, which will cause the subwoofer to turn itself on, even when the Audio-Sense On/Off Switch ¢ has been placed in the AUTO position and no audio signal is detected. The trigger signal must be between 3 and 30 volts, although it may be an AC or DC signal, and an AC signal may be 50Hz or 60Hz. If you'll be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power Switch , to the OFF position. Volume Volume can be adjusted using the Subwoofer-Level Control ¡, as shown. Turn the control knob clockwise to increase the volume of the subwoofer, and counterclockwise to decrease the subwoofer's volume.
Subwoofer Level
Additional Bass Adjustments In addition to the volume adjustments described above, the SUB-TS15 subwoofer includes a Phase Switch and a Filter Switch TM that can be used to adjust the bass response to suit your listening environment or taste. In most situations, the Phase Switch should be left in the NORMAL position. If you suspect that the subwoofer is playing out of phase with the other speakers, which would tend to diminish bass response, try placing this switch in the REVERSE position. There is no harm in experimenting, and you may return the switch to the NORMAL position at any time. If you rearrange your room and reposition the speakers, it would be a good idea to check whether they are in phase by flipping this switch. The High-Cut (Low-Pass) Filter Switch TM limits the frequencies of the audio signal inputted to the subwoofer to the low frequencies that the subwoofer reproduces best. This allows the subwoofer to perform more efficiently, and with superior bass reproduction, minimizing distortion that might occur if the subwoofer attempted to reproduce higher frequencies. This switch should be left in the ON position, except: 1. When the SUB Input § is being used, in which case it has no effect, or 2. When the Speaker-Level Inputs ª or the Line-Level Full-Range Inputs ¶ are being used with a crossover or filter aboard the receiver or processor. In these two circumstances, place the switch in the OFF position.
MIN
MAX
Subwoofer Level
MIN
MAX
10
SUB-TS15
harman/kardon
Test Set Up and Procedure
Equipment needed: · Function/signal generator/sweep generator · Integrated Amplifier · Multimeter · Speaker cables Initial Control Settings: · Power Switch OFF; Filter OFF · Level MIN (Full CCW) · Phase, Auto/On switches do not matter General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single, purple SUB input. 2) Turn on generator; adjust to 75mV, 50 Hz. 3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX) 4) LED should turn from Amber to Blue (on top of UUT); immediate and vigorous bass response should be heard and felt from port tube opening. 5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 7) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise. 8) LED should turn from Amber to Blue; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 6-8 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.0 ohms ±10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
11
SUB-TS15
harman/kardon
12
SUB-TS15
harman/kardon
13
SUB-TS15
harman/kardon
14
SUB-TS15
harman/kardon
15
SUB-TS15
harman/kardon
SUB-TS15 (UL) AMP Troubleshooting Flow Chart
AMP no signal out no yes DC voltage check ±Vcc yes Check+/-15VDC yes LED light green or red LED light green Check U202 pin14 signal
yes yes
Check Fuse,Transformer, D110, etc yes
no Check Q117,118,119,D109 etc yes LED red Check,Q206,Q207,U203 etc
yes yes
no
Check U201 pin14 signal
no
CheckU201,U202,VR201 VR202. etc
no Check limiter board C304
Check U301,R343,R344 , C340,Q301,Q302, etc
yes yes Test R121,R122 signal yes Check RY101,D102,Q113,Q114 etc yes no Check U101,Q115,Q116,R138 etc yes yes Check P102 signal The Amp Ass'y OK, END Set R138 to R140'S Voltage is 0.51VDC yes Check ,+VCC& -VCC no DC voltage no yes Check Q107,Q108,Q105, Q106,Q103,Q104,U101,etc Check J123,J124 etc
16
SUB-TS15
harman/kardon
17
SUB-TS15
harman/kardon
18
SUB-TS15
harman/kardon
19
SUB-TS15
harman/kardon
20
SUB-TS15
harman/kardon
21
SUB-TS15
harman/kardon
22
SUB-TS15
harman/kardon
SUB-TS15 120V Electrical parts list
Part number Description Qty Reference Designator
MAIN/POWER PCB
Resistors 110-10821jk2-e 110-122r2j15-e 110-20331jk2-e 113-50r10j10-e 114-03302m0-e 110-14472j26-e 110-14681j26-e 110-16101j26-e 110-16102j26-e 110-16103j26-e 110-16105j26-e 110-16123j26-e 110-16152j26-e 110-16153j26-e 110-16154j26-e 110-16181j26-e 110-16182j26-e 110-16223j26-e 110-16332j26-e 110-16392j26-e 110-16393j26-e 110-16470j26-e 110-16471j26-e 110-16472j26-e 110-16473j26-e 110-16560j26-e 110-16563j26-e 110-16682j26-e Capacitors 130-2b102k503-e 130-3f104z503-e 130-3f473m503-e 130-sl101k503-e 132-104j503-e 132-223ja03-e 135-3105m50-e 135-3107m16-e 135-3226m50-e 135-3227m10-e 135-3227m16-e 135-3476m25-e 130-3f472md00-e 132-223ja03-e 135-3107m16-e 135-4688m50-e Semiconductors 192-027c1815gr-e 192-028a1015gr-e 192-1572n5551-e 192-1582n5401-e 197-631n4148-e 199-65000333g-e 199-65000623g-e Transistor 2SC1815GR NPN Transistor 2SA1015GR PNP Transistor 2N5551 NPN Transistor 2N5401 AI-PNP 350V DIODE 500mW 75V 1N4148 Panjit (RoHS) ZENER DIODE GDZJ3.3A 500mW 3.3V 2% 26mm (RoHS) ZENER DIODE GDZJ6.2B 500mW 6.2V 26mm 2% (RoHS) 5 2 2 2 4 1 2 Q102,Q111,Q112,Q113,Q118 Q114,Q116 Q103,Q109 Q104,Q110 D101,D103,D105,D108 D102 D106,D107 DISC Capacitor 1000P 50V ±10% (RoHS) DISC Capacitor 0.1U 50V +80/-20% (RoHS) DISC Capacitor 0.047U 50V ±20% (RoHS) DISC Capacitor 100P 50V SL ±10% (RoHS) MYLAR Capacitor 0.1U 50V ±5% (RoHS) MYLAR Capacitor 0.022uF 100V ±5% (RoHS) Electrolytic CAP. 1U 50V ±20% (RoHS) Electrolytic CAP. 100uF 16V ±20% (RoHS) Electrolytic CAP. 22U 50V ±20% (RoHS) Electrolytic CAP. 220U 10V ±20% (RoHS) Electrolytic CAP. 220U 16V ±20% (RoHS) Electrolytic CAP. 47U 25V ±20% (RoHS) DISC Capacitor 4700P 400V ± 20% safe rule long crus (RoHS) MYLAR Capacitor 0.022uF 100V ±5% (RoHS) Electrolytic CAP. 100uF 16V ±20% (RoHS) Electrolytic CAP. 6800U/50V ±20% D25X45mm (RoHS) 1 4 1 2 1 4 2 3 2 2 1 1 1 2 1 2 C116 C108,C113,C115,C119 C106 C139,C140 C107 C124,C125,C126,C128 C105,C112 C109,C117,C120 C114,C118 C129,C130 C111 C103 for Power Switch SW100 C123,C127 C110 C121,C122 Resistor 820 1W ±5% jam crus and shaping 10mm (RoHS) Resistor 2.2 1/2W ±5% prone short crus 15mm (RoHS) Resistor 330 2W ±5% jam crus and shaping 5mm (RoHS) cement Resistor 0.1 5W ±5% standing (RoHS) semi-fixed Resistor 3K 0.3W ±20% (RoHS) Resistor 4.7K 1/4W ±5% CF 26mm (RoHS) Resistor 680 1/4W ±5% CF 26mm (RoHS) Resistor 100 1/6W ±5% CF 26mm Resistor 1K 1/6W ±5% CF 26mm (RoHS) Resistor 10K 1/6W ±5% CF 26mm (RoHS) Resistor 1M 1/6W ±5% CF 26mm (RoHS) Resistor 12K 1/6W ±5% CF 26mm (RoHS) Resistor 1.5K 1/6W ±5% CF 26mm (RoHS) Resistor 15K 1/6W ±5% CF 26mm (RoHS) Resistor 150K 1/6W ±5% CF 26mm (RoHS) Resistor 180 1/6W ±5% CF 26mm (RoHS) Resistor 1.8K 1/6W ±5% CF 26mm (RoHS) Resistor 22K 1/6W ±5% CF 26mm (RoHS) Resistor 3.3K 1/6W ±5% CF 26mm (RoHS) Resistor 3.9K 1/6W ±5% CF 26mm (RoHS) Resistor 39K 1/6W ±5% CF 26mm (RoHS) Resistor 47 1/6W ±5% CF 26mm (RoHS) Resistor 470 1/6W ±5% CF 26mm (RoHS) Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) Resistor 47K 1/6W ±5% CF 26mm (RoHS) Resistor 56 1/6W ±5% CF 26mm (RoHS) Resistor 56K 1/6W ±5% CF 26mm (RoHS) Resistor 6.8K 1/6W ±5% CF 26mm (RoHS) 1 1 2 2 1 2 2 1 1 1 1 2 6 4 1 2 1 3 3 2 1 4 1 3 1 1 1 1 R132 R127 R146,R149 R121,R122 R138 R147,R150 R148,R151 R120 R124 R134 R143 R135,R139 R103,R123,R136,R137,R141,R142 R118,R145,R152,R154 R131 R111,R114 R153 R128,R129,R133 R106,R107,R144 R105,R108 R126 R112,R113,R115,R116 R140 R110,R125,R130 R101 R117 R104 R109
23
SUB-TS15
Part number Description Qty Reference Designator
harman/kardon
MAIN/POWER PCB
199-65001603g-e 190-06m4558d-e 192-021tip35c-e 192-022tip36c-e 192-027c1815gr-e 192-201d882y-e 192-202b772y-e 192-991d669a-e 192-992b649t-e 197-00kbl405-e 197-101n4002-e Miscellaneous 162-10202001-e 171-udhss124d-e 175-1c07v01-e 175-1d02v01-e 175-1d03v01-e 193-3m2520-e 323-AL-00020-0LAE 351-AM03014A094-E 352-AM03008D040-E 361-FE-00051-0LAE 361-NYL-00054-0LAE single wire 26AWG 1007 200mm RED 3mm (RoHS) relay 5A 24V UDH-SS124D (RoHS) WIRE CONNECTOR & BASE 7PIN PITCH=2.5mm (RoHS) WIRE CONNECTOR & BASE 2PIN PITCH=3.96mm (RoHS) WIRE CONNECTOR & BASE 3 PIN PITCH=3.96mm JST-VH (RoHS * INSULATOR TO-3P 25x20mm (RoHS) HEAT SINK 65*32*31 aluminium color M3*14 machine screw electrical black (RoHS) 3*8 B type ping screw electrical black (RoHS) TRANSISTOR stator 14.2*8.0*5.2t=1.6mm (RoHS) TRANSISTOR insulating mat (SW06002) (RoHS) 1 1 1 1 1 2 1 1 4 1 2 ZENER DIODE GDZJ16C 500mW 16V 26mm 2% (RoHS) I.C. OPA 4558D Dual Op-Amp Transistor TIP35C NPN Transistor TIP36C PNP Transistor 2SC1815GR NPN Transistor KSD882Y NPN Transistor KSB772Y PNP TransistorHI-SINCERITY HSD669A NPN Transistor HSB649T PNP bridge rectifier 4A 500V KBL405 (RoHS) diode 1N4002TB (RoHS) 1 1 1 1 2 1 1 1 1 1 1 D109 U101 Q107 Q108 Q101,Q115 Q117 Q119 Q106 Q105 D110 D104
RY101 P101 P102 P103 for Q107,Q108
PREAMP PCB
Resistors 110-12472j52-e 110-16102j26-e 110-16103j26-e 110-16104j26-e 110-16105j26-e 110-16113j26-e 110-16122j26-e 110-16123j26-e 110-16124j26-e 110-16152j26-e 110-16183j26-e 110-16203j26-e 110-16223j26-e 110-16303j26-e 110-16472j26-e 110-16473j26-e 110-16474j26-e 110-16475j26-e 110-16512j26-e 110-16684j26-e 110-16752j26-e 110-16913j26-e 116-169091f26-e 115-h503a102-e 116-201001j5vx-e Capacitors 129-a154j633-e METALIZE CAP. 0.15U 63V ±5% MSC (RoHS) 2 C221,C222 Resistor 4.7K 1/2W ±5% CF 52mm (RoHS) Resistor 1K 1/6W ±5% CF 26mm (RoHS) Resistor 10K 1/6W ±5% CF 26mm (RoHS) Resistor 100K 1/6W ±5% CF 26mm (RoHS) Resistor 1M 1/6W ±5% CF 26mm (RoHS) Resistor 11K 1/6W ±5% 26mm (RoHS) Resistor 1.2K 1/6W ±5% CF 26mm (RoHS) Resistor 12K 1/6W ±5% CF 26mm (RoHS) Resistor 120K 1/6W ±5% CF 26mm (RoHS) Resistor 1.5K 1/6W ±5% CF 26mm (RoHS) Resistor 18K 1/6W ±5% CF 26mm (RoHS) Resistor 20K 1/6W ±5% CF 26mm (RoHS) Resistor 22K 1/6W ±5% CF 26mm (RoHS) Resistor 30K 1/6W ±5% CF 26mm (RoHS) Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) Resistor 47K 1/6W ±5% CF 26mm (RoHS) Resistor 470K 1/6W ±5% CF 26mm (RoHS) Resistor 4.7M 1/6W ±5% CF 26mm (RoHS) Resistor 5.1K 1/6W ±5% CF 26mm (RoHS) Resistor 680K 1/6W CF 26mm (RoHS) Resistor 7.5K 1/6W ±5% CF 26mm TA (RoHS) Resistor 91K 1/6W ±5% CF 26mm (RoHS) metal film Resistor 9.09K 1/6W±1% MF 26mm (RoHS) variable Resistor RV16AE-20B2-15K-A54-104(A50K) LEVEL metalized oxide film Resistor 1K 2W ±5% 5mm (RoHS) 2 6 19 5 1 1 1 1 1 1 1 2 6 2 3 2 1 1 2 1 1 4 1 1 1 R201,R202 R213,R214,R215,R254,R253,R304 R209,R212,R216,R217,R218,R220,R221, R222,R225,R228,R229,R230,R232,R235, R240,R248,R260,R270,R226 R231,R263,R266,R257,R300 R259 R268 R265 R227 R233 R302 R262 R237,R238 R247,R255,R256,R249,R250,R261 R223,R224 R200,R207,R258 R219,R264 R251 R303 R210,R211 R252 R234 R203,R204,R205,R206 R301 VR201 R267
24
SUB-TS15
Part number Description
harman/kardon
Qty Reference Designator
PREAMP PCB
129-a224j633-e 130-2b103k503-e 130-2b221k503-e 130-3f104z503-e 132-183j503-e 132-223ja03-e 132-473j503-e 132-563j503-e 132-823j503-e 135-3105m50-e 135-3106m50-e 135-3107m16-e 135-3226m50-e 135-3475m16-e 135-3107m50-e 135-3227m50-e Semiconductors 192-027c1815gr-e 197-631n4148-e 199-65000513g-e 190-06m4558d-e 190-06m4558ld-e 190-16tl074cn-e 197-141n4004-e 190-05ps25051-e Miscellaneous 162-50122004-e 162-5014d008-e 162-a016d001-e 174-0rca313v-e 174-20810360g-e 174-6ej3556agp-e 175-1b08v01-e 180-tms7210v-e 362-FE-00041-0LAE drop-out line 120mm RED/WHT 2PIN (RoHS) WIRE 2468#26AWG RED/WHT length 140mm (RoHS) mixing wire UL1007 160/80mm#26 (RoHS) RCA JACK RCA-313G V/R/W (RoHS) jack SPK JK BP 8PIN (RoHS) SH0810360G US1.35 PHONE JACK EJ3556A-GP (RoHS) WIRE CONNECTOR & BASE 8 PIN PITCH=2.0mm(RoHS) SWITCH SLIDE 6PIN MS7210V (RoHS) PCB support 11.75*8.5*12.5H (RoHS) 1 1 1 1 1 1 1 3 2 D209 P1-P2 W202 JK201 JK202 JK203 W202 SW201,SW202,SW203 Transistor 2SC1815GR NPN DIODE 500mW 75V 1N4148 Panjit (RoHS) ZENER DIODE GDZJ5.1B 500mW 5.1V 2% ROHM 1N5231B(RoHS I.C. OPA 4558D dual inline (RoHS) I.C. NJRC NJM4558LD singlerow inline (RoHS) Dual Op-amp I.C TL074CN ST Quad Op-Amp *DIODE 1N4004 shaping short crus (RoHS) photoelectric coupler PS2505-1 NEC (RoHS) 4 13 1 1 1 2 4 1 Q201,Q207,Q208,Q206 D201,D202,D203,D204,D205,D206,D207, D208,D214,D215,D216,D301,D302 D213 U203 U204 U201,U202 D217,D218,D219,D220 U1 METALIZE CAP. 0.22uF 63V ±5% MSC (RoHS) DISC Capacitor 0.01u 50V ±10% (RoHS) DISC Capacitor 220P 50V ±10% (RoHS) DISC Capacitor 0.1U 50V +80/-20% (RoHS) MYLAR Capacitor 0.018uF 50V ±5% (RoHS) MYLAR Capacitor 0.022uF 100V ±5% (RoHS) MYLAR Capacitor 0.047U 50V ±5% (RoHS) MYLAR Capacitor 0.056U 50V ±5% (RoHS) MYLAR Capacitor 0.056U 50V ±5% (RoHS) Electrolytic CAP. 1U 50V ±20% (RoHS) Electrolytic CAP. 10uF 50V ±20% (RoHS) Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic CAP. 100uF 16V ±20% (RoHS) CAP. 22U 50V ±20% (RoHS) CAP.4.7U 16V ±20% (RoHS) CAP. 100U 50V ±20% (RoHS) CAP. 220uF 50V ±20% (RoHS) 1 1 12 8 1 1 1 1 1 1 12 1 1 1 1 1 C218 C238 C200,C204,C205,C207,C208,C210,C211, C212,C214,C220,C230,C237 C232,C242,C244,C245,C246,C252,C254, C256 C223 C215 C224 C216 C217 C228 C201,C202,C206,C213,C219,C231,C241, C243,C251,C253,C248,C247 C234 C225 C233 C301 C300
LIMITER PCB
Resistors 110-16103j26-e 110-16153j26-e 110-16223j26-e 110-16333j26-e 110-16474j26-e 110-16751j26-e 110-16755j26-e Capacitors 135-3226m50-e 135-3476m25-e 130-3f104z503-e Electrolytic CAP. 22U 50V ±20% (RoHS) Electrolytic CAP. 47U 25V ±20% (RoHS) DISC Capacitor 0.1U 50V +80/-20% (RoHS) 1 1 2 C301 C304 C305,C306 Resistor 10K 1/6W ±5% CF 26mm (RoHS) Resistor 15K 1/6W ±5% CF 26mm (RoHS) Resistor 22K 1/6W ±5% CF 26mm (RoHS) Resistor 33K 1/6W ±5% CF 26mm (RoHS) Resistor 470K 1/6W ±5% CF 26mm (RoHS) Resistor 750 1/6W ±5% CF 26mm (RoHS) Resistor 7.5M 1/6W ±5% CF 26mm (RoHS) 6 1 2 1 1 2 1 R301,R303,R304,R308,R309,R314 R302 R310,R312 R305 R307 R311,R313 R306
25
SUB-TS15
Part number Description Qty Reference Designator
harman/kardon
LIMITER PCB
132-103j503-e Semiconductors 190-16tl074cn-e 192-027c1815gr-e 197-631n4148-e Miscellaneous 175-9f40hr2-e 162-10059001-e 162-50159002-e WIRE CONNECTOR & BASE 40PIN PITCH=2.54mm HR2*40 (RoHS) single wire 50mm WHITE UL1007 AWG26 6:6 (RoHS) 1 WIRE 7PIN 150mm AWG26 UL 2468 (RoHS) 1 *I.C TL074CN ST QUAD OP-AMP *Transistor 2SC1815GR NPN Diode1N4148 26mm 1 2 2 U301 Q301,Q302 D301,D302 MYLAR Capacitor 0.01uF 50V ±5% (RoHS) 2 C302,C303
P302
MISCELLANEOUS/MECHANICAL
150-e8604107-e Power transformer EI-86 60Hz 120V TT0869906580 152-u602015-e power cord joint SVT FT-2 6FT bi-insulation (RoHS) 154-u25006t0-e fuse 2.5A 250V 20mm (RoHS) 155-520020-e fuse holder R3-11 (RoHS) 162-10082007-e WIRE RED 18AWG 80mm 8mm#1015 (RoHS) 162-5020d006-e WIRE UL2468 200mm 2.5mmpitch RED/WHT (RoHS) 162-a0452001-e WIRE UL1007 #16 450mm #110/ #205 0.5T (RoHS) 176-wjce1-e dead end CE-1 (RoHS) 180-pbr12c11s-e power PUSH BR12C11S (RoHS) POWER ON-OFF 302-AL-00435-1BFE aluminium backboard 270*215*2.5T anode blackening (RoHS) 306-ABS-00004-0BAE rear housing REAR CABINET 268*213*102 A.B.S UL (RoHS) 311-ABS-00028-0BAE plastic KNOB 46077-W soft material P.V.C. (RoHS) LEVEL 320-RUB-00033-0BAE RUBBER PAD 25*21*4t glue on back (RoHS) 323-AL-00106-0BBE HEAT SINK 117.5*71.5*25 anode blackening (RoHS) 333-EVA-00096-0BAE EVA pad wide sides213*15*2.0mm (RoHS) 333-EVA-00097-0BAE EVA pad wide sides213*15*1.0t (RoHS) 333-EVA-00121-0BAE 8PIN BB EVA (RoHS) 333-EVA-00132-0BAE EVA pad long sides238*15*2.0mm (RoHS) 333-EVA-00133-0BAE EVA pad long sides238*15*1.0t (RoHS) 333-EVA-00188-0BAE EVA pad 170x5x1t glue on back (RoHS) 333-EVA-00220-0BAE EVA pad length sides225*15*1t UL (RoHS) 333-EVA-00866-0BAE EVA 48*18*1.5T (RoHS) 335-NYL-00002-0BAE WIRE CLIP 4K-4 NO-BB(RoHS) 335-NYL-05015-0BAE power cord fixed button SB4F-2 black (RoHS) 350-EM04012D024-E 4*12 wood screw electrical black (RoHS) 351-AM03008A079-E M3*8 machine screw electrical black (RoHS) 351-HM04016A218-E M4*16 machine screw electrical black (RoHS) 352-AM03008D040-E 3*8 B type ping screw electrical black (RoHS) 352-AM03010D063-E 3*10 B type ping screw electrical black (RoHS) 352-AM03010D065-E 3*10 P type ping screw electrical black (RoHS) 354-GM04002-E M4 nut with gear pad electrical black (RoHS) 362-FE-00013-0LAE PCB support L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS) 1 1 1 1 1 1 1 1 1 1 1 1 4 1 2 2 1 2 2 1 1 1 1 1 4 8 4 6 2 3 4 2
SW100
26
SUB-TS15
harman/kardon
27
SUB-TS15
harman/kardon
28
SUB-TS15
harman/kardon
29
SUB-TS15
harman/kardon
30