Text preview for : SharpServiceModes.pdf part of Sharp Service modes Service modes Sharp
Back to : SharpServiceModes.pdf | Home
CTV990504 TELEVISION TECHNICAL BULLETIN
Month of Issue: May 1999 Classification: White Page 1 of 7
MODELS
BCTVA Chassis CW100 Chassis DECO-5 Chassis S3B Chassis
4BS-C Chassis CS Chassis 4BS-B Chassis
CA1 Chassis D3000 Chassis 4BS-A Chassis
CA10 Chassis DECO-4 Chassis 5BS- A Chassis
To assist with the adjustments of the above chassis, the list below details how to enter the various service modes. BCTVA Chassis
66AS06H, DV5932H, DV5935H, DV5937H and DV6635H
1. 2. 3. 4. 5. Connect a test pattern to the antenna terminal Tune to this signal Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit SERVICE SOFTWARE will appear on the screen Remove the jumper wire
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units
CTV990504 TELEVISION TECHNICAL BULLETIN
4BS-C Chassis
DV5940H, DV6640H and 66AS05H
1. 2. 3. 4. 5. Connect a test pattern to the antenna terminal Tune to this signal Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Text Unit SERVICE SOFTWARE will appear on the screen Remove the jumper wire
Month of Issue: May 1999 Classification: White Page 2 of 7
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
CA1 Chassis
37DM23H, 37DT25H, 37ET35H, 37EM33H and 51DT25H
1. 2. 3. 4. 5. 6. 7. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed, turn the mains on When the set starts up it will be in service mode Release the two buttons
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control.
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units
CTV990504 TELEVISION TECHNICAL BULLETIN
CA10 Chassis
51DS02H, 51DS03H, 51DS05H, 59DS03H, 59DS05H, 59ES03H, 59ES05H, 59ESD7H, 66DS03H, 66DS05H, 66ES05H and 66ESD7H
1. 2. 3. 4. 5. 6. 7. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed, turn the mains on When the set starts up it will be in service mode Release the two buttons
Month of Issue: May 1999 Classification: White Page 3 of 7
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
CS Chassis
51CS03H, 51CS05H, 59CS03H, 59CS05H, 59CSD8H, 66CS03H, 66CS05H and 66CSD8H
1. 2. 3. 4. 5. 6. 7. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed, turn the mains on When the set starts up it will be in service mode Release the two buttons
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
CW100 Chassis
66DW18H and 76DW18H
1. 2. 3. 4. 5. 6. 7. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed, turn the mains on When the set starts up it will be in service mode Release the two buttons
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units
CTV990504 TELEVISION TECHNICAL BULLETIN
D3000 Chassis
DV51083H, DV5903H, DV59083H, DV6603H and DV66083H
1. 2. 3. 4. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver on Press the service switch (S1401) located on the Video PWB
Month of Issue: May 1999 Classification: White Page 4 of 7
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode
4BS-B Chassis
DV5165H and DV5180H
1. 2. 3. 4. 5. 6. 7. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed, turn the mains on When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen Release the two buttons
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units
CTV990504 TELEVISION TECHNICAL BULLETIN
DECO-4 and Deco-5 Chassis's
DV5105H (DECO-4) DV5107H, DV5132H and DV5135H (DECO-5)
Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver on Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen 1. 2. 3. 4.
Month of Issue: May 1999 Classification: White Page 5 of 7
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units
CTV990504 TELEVISION TECHNICAL BULLETIN
4BSA Chassis
DV3760H, DV3770H and DV5161H
1. 2. 3. 4. 5. 6. Connect a test pattern to the antenna terminal Tune to this signal Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB Press the MODE button on the remote control 'SERV' will appear on the screen Remove the jumper wire
Month of Issue: May 1999 Classification: White Page 6 of 7
To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode.
5BSA Chassis
37AM12H, 37AM23H, 37AT25H and 51AT15H
1. 2. 3. 4. 5. 6. 7. Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed, turn the mains on When the set starts up it will be in service mode - 'SERV' appears on the screen Release the two buttons
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units
CTV990504 TELEVISION TECHNICAL BULLETIN
S3B Chassis DV3750H, DV3751H, DV5131H and DV5150H 1. 2. 3. 4. 5. 6. Connect a test pattern to the antenna terminal Tune to this signal Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB Press the MODE button on the remote control 'SERV' will appear on the screen Remove the jumper wire
Month of Issue: May 1999 Classification: White Page 7 of 7
Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp Electronics (UK) Limited
Reference AVW060599/1 Revision 1 White Carry out as required, Yellow Carry out as required and whenever the unit comes in for service, Red Carry out on all units